View LD1117AXX33_3277261.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/16 october 2003 n low dropout voltage (1.15v typ. @ i out =1a,25c) n very low quiescent current (5 ma typ. @ 25c) n output current up to 1a n fixed output voltage of: 1.8v, 2.5v, 2.85v, 3.3v, 5.0v n adjustable version availability (v rel = 1.25v) n internal current and thermal limit n only 10 f for stability n available in 2% (at 25c) and 4% in full temperature range n high supply voltage rejection: (80db typ. at 25c) n temperature range: 0c to 125c description the ld1117a is a low drop voltage regulator able to provide up to 1a of output current, available even in adjustable version (vref=1.25v). concerning fixed versions, are offered the following output voltages: 1.8v, 2.5v, 2.85v, 3.3v and 5.0v. the 2.85v type is ideal for scsi-2 lines active termination. the device is supplied in: sot-223, dpak and to-220. the surface mount packages optimize the thermal characteristics even offering a relevant space saving effect. high efficiency is assured by npn pass transistor. only a very common 10f minimum capacitor is needed for stability. only chip trimming allows the regulator to reach a very tight output voltage tolerance, within 2% at 25 c. ld1117a series low drop fixed and adjustable positive voltage regulators block diagram sot-223 dpak to-220
ld1117a series 2/16 absolute maximum ratings absolute maximum ratings are those values beyond which damage to the device may occur. functional operation under these condition is not implied. over the above suggested max power dissipation a short circuit could definitively damage the device. thermal data application circuit (for other fixed output voltages) symbol parameter2 value unit v in dc input voltage 10 v p tot power dissipation 12 w t stg storage temperature range -40 to +150 c t op operating junction temperature range 0 to +125 c symbol parameter to-220 sot-223 dpak unit r thj-case thermal resistance junction-case 3 15 8 c/w r thj-amb thermal resistance junction-ambient 50 c/w
ld1117a series 3/16 connection diagram (top view) note: the tab is connected to the v out . ordering codes sot-223 dpak to-220 output voltage ld1117as18tr ld1117adt18tr ld1117av18 1.8 v ld1117as25tr ld1117adt25tr ld1117av25 2.5 v ld1117as28tr ld1117adt28tr ld1117av28 2.85 v ld1117as33tr ld1117adt33tr ld1117av33 3.3 v ld1117as50tr ld1117adt50tr ld1117av50 5 v ld1117ast-r ld1117adt-r ld1117av adjustable from 1.25 to 15 v sot-223 dpak to-220
ld1117a series 4/16 electrical characteristics of ld1117a#18 (refer to the test circuits, t j = 0 to 125c, c o =10f,c i = 10 f unless otherwise specified) electrical characteristics of ld1117a#25 (refer to the test circuits, t j = 0 to 125c, c o =10f,c i = 10 f unless otherwise specified) symbol parameter test conditions min. typ. max. unit v o output voltage v i = 3.8 v i o =10ma t j = 25c 1.764 1.8 1.836 v v o output voltage i o =0to1a v i = 3.3 to 8 v 1.728 1.872 v d v o line regulation v i = 3.3 to 8 v i o = 0 ma 1 6 mv d v o load regulation v i = 3.3 v i o = 0 to 1 a 1 10 mv d v o temperature stability 0.5 % d v o long term stability 1000 hrs, t j = 125c 0.3 % v i operating input voltage i o = 100 ma 10 v i d quiescent current v i 8v i o = 0 ma 5 10 ma i o output current v i -v o =5v t j = 25c 1000 ma en output noise voltage b =10hz to 10khz t j = 25c 100 m v svr supply voltage rejection i o = 40 ma f = 120hz v i -v o =3v v ripple =1v pp 60 80 db v d dropout voltage i o = 100 ma 1 1.10 v i o = 500 ma 1.05 1.15 i o = 1 a 1.15 1.30 d v o(pwr) thermal regulation t a = 25c 30ms pulse 0.08 0.2 %/w symbol parameter test conditions min. typ. max. unit v o output voltage v i = 4.5 v i o =10ma t j = 25c 2.45 2.5 2.55 v v o output voltage i o =0to1a v i = 3.9 to 8 v 2.4 2.6 v d v o line regulation v i = 3.9 to 8 v i o = 0 ma 1 6 mv d v o load regulation v i = 3.9 v i o = 0 to 1 a 1 10 mv d v o temperature stability 0.5 % d v o long term stability 1000 hrs, t j = 125c 0.3 % v i operating input voltage i o = 100 ma 10 v i d quiescent current v i 10 v i o = 0 ma 5 10 ma i o output current v i -v o =5v t j = 25c 1000 1200 ma en output noise voltage b =10hz to 10khz t j = 25c 100 m v svr supply voltage rejection i o = 40 ma f = 120hz v i -v o =3v v ripple =1v pp 60 80 db v d dropout voltage i o = 100 ma 1 1.10 v i o = 500 ma 1.05 1.15 i o = 1 a 1.15 1.30 d v o(pwr) thermal regulation t a = 25c 30ms pulse 0.08 0.2 %/w
ld1117a series 5/16 electrical characteristics of ld1117a#28 (refer to the test circuits, t j = 0 to 125c, c o =10f,c i = 10 f unless otherwise specified) electrical characteristics of ld1117a#33 (refer to the test circuits, t j = 0 to 125c, c o =10f,c i = 10 f unless otherwise specified) symbol parameter test conditions min. typ. max. unit v o output voltage v i = 4.85 v i o =10ma t j = 25c 2.793 2.85 2.907 v v o output voltage i o =0to1a v i = 4.25 to 10 v 2.736 2.964 v d v o line regulation v i = 4.25 to 8 v i o = 0 ma 1 6 mv d v o load regulation v i = 4.25 v i o = 0 to 1 a 1 10 mv d v o temperature stability 0.5 % d v o long term stability 1000 hrs, t j = 125c 0.3 % v i operating input voltage i o = 100 ma 10 v i d quiescent current v i 10 v i o = 0 ma 4.5 10 ma i o output current v i -v o =5v t j = 25c 1000 1200 ma en output noise voltage b =10hz to 10khz t j = 25c 100 m v svr supply voltage rejection i o = 40 ma f = 120hz v i -v o =3v v ripple =1v pp 60 75 db v d dropout voltage i o = 100 ma 1 1.10 v i o = 500 ma 1.05 1.15 i o = 1 a 1.15 1.30 d v o(pwr) thermal regulation t a = 25c 30ms pulse 0.08 0.2 %/w symbol parameter test conditions min. typ. max. unit v o output voltage v i = 5.3 v i o =10ma t j = 25c 3.234 3.3 3.366 v v o output voltage i o =0to1a v i = 4.75 to 10 v 3.168 3.432 v d v o line regulation v i = 4.75 to 8 v i o = 0 ma 1 6 mv d v o load regulation v i = 4.75 v i o = 0 to 1 a 1 10 mv d v o temperature stability 0.5 % d v o long term stability 1000 hrs, t j = 125c 0.3 % v i operating input voltage i o = 100 ma 10 v i d quiescent current v i 10 v i o = 0 ma 5 10 ma i o output current v i -v o =5v t j = 25c 1000 1200 ma en output noise voltage b =10hz to 10khz t j = 25c 100 m v svr supply voltage rejection i o = 40 ma f = 120hz v i -v o =3v v ripple =1v pp 60 75 db v d dropout voltage i o = 100 ma 1 1.10 v i o = 500 ma 1.05 1.15 i o = 1 a 1.15 1.30 d v o(pwr) thermal regulation t a = 25c 30ms pulse 0.08 0.2 %/w
ld1117a series 6/16 electrical characteristics of ld1117a#50 (refer to the test circuits, t j = 0 to 125c, c o =10f,c i = 10 f unless otherwise specified) electrical characteristics of ld1117a (adjustable) (refer to the test circuits, t j =0to 125c, c o =10f,c i = 10 f unless otherwise specified) symbol parameter test conditions min. typ. max. unit v o output voltage v i =7v i o =10ma t j = 25c 4.9 5 5.1 v v o output voltage i o =0to1a v i = 6.4 to 10 v 4.8 5.2 v d v o line regulation v i = 6.4 to 8 v i o = 0 ma 1 6 mv d v o load regulation v i = 6.4 v i o = 0 to 1 a 1 10 mv d v o temperature stability 0.5 % d v o long term stability 1000 hrs, t j = 125c 0.3 % v i operating input voltage i o = 100 ma 10 v i d quiescent current v i 10 v i o = 0 ma 5 10 ma i o output current v i -v o =5v t j = 25c 1000 1200 ma en output noise voltage b =10hz to 10khz t j = 25c 100 m v svr supply voltage rejection i o = 40 ma f = 120hz v i -v o =3v v ripple =1v pp 60 80 db v d dropout voltage i o = 100 ma 1 1.10 v i o = 500 ma 1.05 1.15 i o = 1 a 1.15 1.30 d v o(pwr) thermal regulation t a = 25c 30ms pulse 0.08 0.2 %/w symbol parameter test conditions min. typ. max. unit v o output voltage v i = 5.3 v i o =10ma t j = 25c 1.225 1.25 1.275 v v o output voltage i o =0to1a v i = 2.75 to 10 v 1.2 1.3 v d v o line regulation v i = 2.75 to 8 v i o = 0 ma 1 6 mv d v o load regulation v i = 2.75 v i o = 0 to 1 a 1 10 mv d v o temperature stability 0.5 % d v o long term stability 1000 hrs, t j = 125c 0.3 % v i operating input voltage i o = 100 ma 10 v i d quiescent current v i 8v i o = 0 ma 5 10 ma i o output current v i -v o =5v t j = 25c 1000 1200 ma en output noise voltage b =10hz to 10khz t j = 25c 100 m v svr supply voltage rejection i o = 40 ma f = 120hz v i -v o =3v v ripple =1v pp 60 80 db v d dropout voltage i o = 100 ma 1 1.10 v i o = 500 ma 1.05 1.15 i o = 1 a 1.15 1.30 d v o(pwr) thermal regulation t a = 25c 30ms pulse 0.08 0.2 %/w
ld1117a series 7/16 typical applications figure 1 : negative supply figure 2 : active terminator for scsi-2 bus figure 3 : circuit for increasing output voltage
ld1117a series 8/16 figure 4 : voltage regulator with reference figure 5 : battery backed-up regulated supply
ld1117a series 9/16 figure 6 : post-regulated dual supply
ld1117a series 10/16 ld1117a adjustable: application note the ld1117a adjustable has a thermal stabilized 1.250.012v reference voltage between the out and adj pins. i adj is 60a typ. (120a max.) and d i adj is 1a typ. (5a max.). r1 is normally fixed to 120 w . from figure 7 we obtain: v out =v ref +r2(i adj +i r1 )=v ref +r2(i adj +v ref /r1) = v ref (1 + r2 / r1) + r2 x i adj . in normal application r2 value is in the range of few kohm, so the r2 x i dj product could not be considered in the v out calculation; then the above expression becomes: v out =v ref (1 + r2 / r1). in order to have the better load regulation it is important to realize a good kelvin connection of r1 and r2 resistors. in particular r1 connection must be realized very close to out and adj pin, while r2 ground connection must be placed as near as possible to the negative load pin. ripple rejection can be improved by introducing a 10f electrolytic capacitor placed in parallel to the r2 resistor (see fig.8). figure 7 : adjustable output voltage application figure 8 : adjustable output voltage application with improved ripple rejection
ld1117a series 11/16 dim. mm. mils min. typ max. min. typ. max. a 1.8 70.9 a1 0.02 0.1 0.8 3.9 b 0.6 0.7 0.8523.627.633.5 b1 2.9 3 3.15 114.2 118.1 124.0 c 0.24 0.26 0.35 9.4 10.2 13.8 d 6.3 6.5 6.7 248.0 255.9 263.8 e 2.3 90.6 e1 4.6 181.1 e 3.3 3.5 3.7 129.9 137.8 145.7 h 6.7 7 7.3 129.9 137.8 145.7 v 10? sot-223 mechanical data 0046067/h 10?
ld1117a series 12/16 dim. mm. inch min. typ max. min. typ. max. a 2.2 2.4 0.086 0.094 a1 0.9 1.1 0.035 0.043 a2 0.03 0.23 0.001 0.009 b 0.64 0.9 0.025 0.035 b2 5.2 5.4 0.204 0.212 c 0.45 0.6 0.017 0.023 c2 0.48 0.6 0.019 0.023 d 6 6.2 0.236 0.244 e 6.4 6.6 0.252 0.260 g 4.4 4.6 0.173 0.181 h 9.35 10.1 0.368 0.397 l2 0.8 0.031 l4 0.6 1 0.023 0.039 dpak mechani cal data 0068772-b
ld1117a series 13/16 dim. mm. inch min. typ max. min. typ. max. a 4.40 4.60 0.173 0.181 c 1.23 1.32 0.048 0.051 d 2.40 2.72 0.094 0.107 d1 1.27 0.050 e 0.49 0.70 0.019 0.027 f 0.61 0.88 0.024 0.034 f1 1.14 1.70 0.044 0.067 f2 1.14 1.70 0.044 0.067 g 4.95 5.15 0.194 0.203 g1 2.4 2.7 0.094 0.106 h2 10.0 10.40 0.393 0.409 l2 16.4 0.645 l4 13.0 14.0 0.511 0.551 l5 2.65 2.95 0.104 0.116 l6 15.25 15.75 0.600 0.620 l7 6.2 6.6 0.244 0.260 l9 3.5 3.93 0.137 0.154 dia. 3.75 3.85 0.147 0.151 to-220 mechanical dat a p011c
ld1117a series 14/16 dim. mm. inch min. typ max. min. typ. max. a 180 7.086 c 12.8 13.0 13.2 0.504 0.512 0.519 d 20.2 0.795 n 60 2.362 t 14.4 0.567 ao 6.73 6.83 6.93 0.265 0.269 0.273 bo 7.32 7.42 7.52 0.288 0.292 0.296 ko 1.78 2 0.070 0.078 po 3.9 4.0 4.1 0.153 0.157 0.161 p 7.9 8.0 8.1 0.311 0.315 0.319 tape & reel sot223 mechanical data
ld1117a series 15/16 dim. mm. inch min. typ max. min. typ. max. a 330 12.992 c 12.8 13.0 13.2 0.504 0.512 0.519 d 20.2 0.795 n 60 2.362 t 14.4 0.567 ao 6.80 6.90 7.00 0.268 0.272 0.2.76 bo 10.40 10.50 10.60 0.409 0.413 0.417 ko 2.55 2.65 2.75 0.100 0.104 0.105 po 3.9 4.0 4.1 0.153 0.157 0.161 p 7.9 8.0 8.1 0.311 0.315 0.319 tape & reel dpak-ppak mechanical data
ld1117a series 16/16 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result f rom its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specificati ons mentioned in this publication are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectronics. the st logo is a registered trademark of stmicroelectronics all other names are the property of their respective owners ? 2003 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states. http://www.st.com

▲Up To Search▲

Price & Availability of LD1117AXX33

	To Download LD1117AXX33 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .