12-61 photocoupler high sensitivity type photocoupler ltv-715f series ordering information part number package safety standard approval application part number ltv-715f ltv-715fm ltv-715fs LTV-715FS-TA LTV-715FS-TA1 ltv715f-v ltv715fm-v ltv715fs-v ltv715fsta-v ltv715fsta1-v 6-pin dip 6-pin (leads with 0.4" spacing) 6-pin (lead bends for surface mount) 6-pin (tape and reel packaging of type i) 6-pin (tape and reel packaging of type ii) 6-pin dip 6-pin (leads with 0.4" spacing) 6-pin (lead bends for surface mount) 6-pin (tape and reel packaging of type i) 6-pin (tape and reel packaging of type ii) ul approved nemko approved csa approved demko approved fimko approved semko approved vde approved ltv - 715f ltv - 715f features low collector dark current ( i ceo : max. 10 -6 a at v ce = 10v ) current transfer ratio ( ctr : min. 600% at i f = 1ma, v ce = 2v ) high input-output isolation voltage ( v iso = 5,000vrms ) response time ( t r : typ. 60 s at v ce = 2v, i c = 10ma, r l = 100 ) ul approved ( no. e113898 ) csa approved ( no. ca91533-1 ) fimko approved ( no. 202944 ) nemko approved ( no. p98101737 ) demko approved ( no. 307925 ) semko approved ( no. 9833170/01 ) vde approved ( no. 094722 ) options available : - leads with 0.4" (10.16mm) spacing (m type) - lead bends for surface mounting (s type) - tape and reel of type i for smd (add "-ta" suffix) - tape and reel of type ii for smd (add "-ta1" suffix) - vde 0884 approvals (add "-v" suffix) applications 1. system appliances, measuring instruments 2. copiers, automatic vending machines 3. signal transmission between circuits of different poten- tials and impedances package dimensions notes : 1. year date code. 2. 2-digit work week. 3. factory code shall be marked (z taiwan, y thailand). 4. all dimensions are in millimeters (inches). 5. tolerance is 0.25mm (.010") unless otherwise noted. 6. specifications are subject to change without notice.
12-62 *1. ac for 1 minute, r.h. = 40 ~ 60% isolation voltage shall be measured using the following method. (1) short between anode and cathode on the primary side and between collector and emitter on the secondary side. (2) the isolation voltage tester with zero-cross circuit shall be used. (3) the waveform of applied voltage shall be a sine wave. *2. for 10 seconds ratings and characteristics absolute maximum ratings (ta=25 parameter symbol rating unit input output total power dissipation operating temperature s torage temperature *1.isolation voltage *2.soldering temperature forward current reverse voltage power dissipation collector-emitter voltage emitter-collector voltage collector current collector power dissipation i f v r p v ceo v eco i c p c p tot v iso t opr t stg t sol 50 6 70 35 6 80 150 170 5,000 -25~+100 -40~+125 260 ma v mw v v ma mw mw vrms parameter symbol min. typ. max. unit conditions input output transfer characteristics forward voltage reverse current terminal capacitance collector dark current collector-emitter breakdown voltage emitter-collector breakdown voltage collector current *1 current transfer ratio collector-emitter saturation voltage isolation resistance floating capacitance cut-off frequency response time (rise) response time (fall) v f i r c t i ceo bv ceo bv eco i c ctr v ce(sat) r iso c f f c t r t f 35 6 6 600 5 10 10 1.2 30 1 10 11 0.6 6 60 53 1.4 10 250 10 -6 75 7500 1 1 250 250 v a pf a v v ma % v pf khz s s *1 ctr= 100% i c i f i f =10ma v r =4v v=0, f=1khz v ce =10v, i f =0 i c =0.1ma i f =0 i e =10 a i f =0 i f =1ma v ce =2v i f =20ma i c =5ma dc500v 40~60%r.h. v=0, f=1mh z v ce =2v, i c =2ma r l =100 , -3db v ce =2v, i c =10ma r l =100 electrical / optical characteristics (ta=25 )
12-63 photocoupler typical electrical/optical characteristic curves (25 ambient temperature unless otherwise noted)
12-64
|
