pin configurations 8-pin to-99 8-pin dip rev. a information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of analog devices. a pin programmable precision voltage reference ad584* features four programmable output voltages: 10.000 v, 7.500 v, 5.000 v, 2.500 v laser-trimmed to high accuracies no external components required trimmed temperature coefficient: 5 ppm/ 8 c max, 0 8 c to +70 8 c (ad584l) 15 ppm/ 8 c max, C55 8 c to +125 c (ad584t) zero output strobe terminal provided two terminal negative reference capability (5 v & above) output sources or sinks current low quiescent current: 1.0 ma max 10 ma current output capability mil-std-883 compliant versions available general description the ad584 is an eight-terminal precision voltage reference of- fering pin-programmable selection of four popular output volt- ages: 10.000 v, 7.500 v, 5.000 v and 2.500 v. other output voltages, above, below or between the four standard outputs, are available by the addition of external resistors. input voltage may vary between 4.5 and 30 volts. laser wafer trimming (lwt) is used to adjust the pin-pro- grammable output levels and temperature coefficients, resulting in the most flexible high precision voltage reference available in monolithic form. in addition to the programmable output voltages, the ad584 offers a unique strobe terminal which permits the device to be turned on or off. when the ad584 is used as a power supply reference, the supply can be switched off with a single, low- power signal. in the off state the current drain by the ad584 is reduced to about 100 m a. in the on state the total supply current is typically 750 m a including the output buffer amplifier. the ad584 is recommended for use as a reference for 8-, 10- or 12-bit d/a converters which require an external precision refer- ence. the device is also ideal for all types of a/d converters of up to 14-bit accuracy, either successive approximation or inte- grating designs, and in general can offer better performance than that provided by standard self-contained references. the ad584j, k and l are specified for operation from 0 c to +70 c; the ad584s and t are specified for the C55 c to +125 c range. all grades are packaged in a hermetically sealed eight-terminal to-99 metal can; the ad584 j and k are also available in an 8-pin plastic dip. * protected by u.s. patent no. 3,887,863; re 30,586 one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 617/329-4700 fax: 617/326-8703 product highlights 1. the flexibility of the ad584 eliminates the need to design- in and inventory several different voltage references. fur- thermore one ad584 can serve as several references simultaneously when buffered properly. 2. laser trimming of both initial accuracy and temperature co- efficient results in very low errors over temperature without the use of external components. the ad584lh has a maxi- mum deviation from 10.000 volts of 7.25 mv from 0 c to +70 c. 3. the ad584 can be operated in a two-terminal zener mode at 5 volts output and above. by connecting the input and the output, the ad584 can be used in this zener con- figuration as a negative reference. 4. the output of the ad584 is configured to sink or source currents. this means that small reverse currents can be tol- erated in circuits using the ad584 without damage to the reference and without disturbing the output voltage (10 v, 7.5 v and 5 v outputs). 5. the ad584 is available in versions compliant with mil- std-883. refer to the analog devices military products databook or current ad584/883b data sheet for detailed specifications.
ad584Cspecifications model ad584j ad584k ad584l min typ max min typ max min typ max units output voltage tolerance maximum error 1 for nominal outputs of: 10.000 v 6 30 6 10 6 5 mv 7.500 v 6 20 6 8 6 4 mv 5.000 v 6 15 6 6 6 3 mv 2.500 v 6 7.5 6 3.5 6 2.5 mv output voltage change maximum deviation from +25 c value, t min to t max 2 10.000 v, 7.500 v, 5.000 v outputs 30 15 5 ppm/ c 2.500 v output 30 15 10 ppm/ c differential temperature coefficients between outputs 5 3 3 ppm/ c quiescent current 0.75 1.0 0.75 1.0 0.75 1.0 ma temperature variation 1.5 1.5 1.5 m a/ c turn-on settling time to 0.1% 200 200 200 m s noise (0.1 hz to 10 hz) 50 50 50 m v p-p long-term stability 25 25 25 ppm/1000 hrs short-circuit current 30 30 30 ma line regulation (no load) 15 v v in 30 v 0.002 0.002 0.002 %/v (v out +2.5 v) v in 15 v 0.005 0.005 0.005 %/v load regulation 0 i out 5 ma, all outputs 20 50 20 50 20 50 ppm/ma output current v in 3 v out +2.5 v source @ +25 c 101010ma source t min to t max 555ma sink t min to t max 555ma temperature range operating 0 +70 0 +70 0 +70 c storage C65 +175 C65 +175 C65 +175 c package option 3 to-99 (h-08a) ad584jh ad584kh ad584lh plastic (n-8) ad584jn AD584KN rev. a C2C metalization photograph dimensions shown in inches and (mm). notes 1 at pin 1. 2 calculated as average over the operating temperature range. 3 h = hermetic metal can; n = plastic dip. specifications subject to change without notice. specifications shown in boldface are tested on all production units at final electrical test. results from those tests are used to calculate outgoing quality levels. all min and max specifications are guaranteed, although only those shown in boldface are tested on all production units. absolute maximum ratings input voltage v in to ground . . . . . . . . . . . . . . . . . . . . . . . 40 v power dissipation @ +25 c . . . . . . . . . . . . . . . . . . . . 600 mw operating junction temperature range . . . . C55 c to +125 c lead temperature (soldering 10 sec) . . . . . . . . . . . . . +300 c thermal resistance junction-to-ambient (h-08a) . . . . . . . . . . . . . . . . 150 c/w (@ v in = +15 v and 25 8 c)
ad584 model ad584s ad584t min typ max min typ max units output voltage tolerance maximum error 1 for nominal outputs of: 10.000 v 6 30 6 10 mv 7.500 v 6 20 6 8 mv 5.000 v 6 15 6 mv 2.500 v 6 7.5 6 3.5 mv output voltage change maximum deviation from +25 c value, t min to t max 2 10.000 v, 7.500 v, 5.000 v outputs 30 15 ppm/ c 2.500 v output 30 20 ppm/ c differential temperature coefficients between outputs 5 3 ppm/ c quiescent current 0.75 1.0 0.75 1.0 ma temperature variation 1.5 1.5 m a/ c turn-on settling time to 0.1% 200 200 m s noise (0.1 hz to 10 hz) 50 50 m v p-p long-term stability 25 25 ppm/1000 hrs short-circuit current 30 30 ma line regulation (no load) 15 v v in 30 v 0.002 0.002 %/v (v out +2.5 v) v in 15 v 0.005 0.005 %/v load regulation 0 i out 5 ma, all outputs 20 50 20 50 ppm/ma output current v in 3 v out +2.5 v source @ +25 c1010ma source t min to t max 55ma sink t min to t max 55ma temperature range operating C55 +125 C55 +125 c storage C65 +175 C65 +175 c package option to-99 (h-08a) ad584sh ad584th notes 1 at pin 1. 2 calculated as average over the operating temperature range. specifications subject to change without notice. specifications shown in boldface are tested on all production units at final electrical test. results from those tests are used to calculate outgoing quality levels. all min and max specifications are guaranteed, although only those shown in boldface are tested on all production units. rev. a C3C
ad584 rev. a C4C range will be about 20 v even for large values of r1. r2 should not be omitted; its value should be chosen to limit the output to a value which can be tolerated by the load circuits. if r2 is zero, adjusting r1 to its lower limit will result in a loss of control over the output voltage. if precision voltages are required to be set at levels other than the standard outputs, the 20% absolute toler- ance in the internal resistor ladder must be accounted for. alternatively, the output voltage can be raised by loading the 2.5 v tap with r3 alone. the output voltage can be lowered by connecting r4 alone. either of these resistors can be a fixed resistor selected by test or an adjustable resistor. in all cases the resistors should have a low temperature coefficient to match the ad584 internal resistors, which have a negative t.c. less than 60 ppm/ c. if both r3 and r4 are used, these resistors should have matched temperature coefficients. when only small adjustments or trims are required, the circuit of figure 2 offers better resolution over a limited trim range. the circuit can be programmed to 5.0 v, 7.5 v or 10 v and ad- justed by means of r1 over a range of about 200 mv. to trim the 2.5 v output option, r2 (figure 2) can be reconnected to the bandgap reference (pin 6). in this configuration, the adjust- ment should be limited to 100 mv in order to avoid affecting the performance of the ad584. figure 2. output trimming figure 3. schematic diagram applying the ad584 with power applied to pins 8 and 4 and all other pins open, the ad584 will produce a buffered nominal 10.0 v output between pins 1 and 4 (see figure 1). the stabilized output voltage may be reduced to 7.5 v, 5.0 v or 2.5 v by connecting the program- ming pins as follows: output voltage pin programming 7.5 v join the 2.5 v and 5.0 v pins (2) and (3) 5.0 v connect the 5.0 v pin (2) to the output pin (1). 2.5 v connect the 2.5 v pin (3) to the output pin (1). the options shown above are available without the use of any additional components. multiple outputs using only one ad584, are also possible by simply buffering each voltage pro- gramming pin with a unity-gain noninverting op amp. figure 1. variable output options the ad584 can also be programmed over a wide range of out- put voltages, including voltages greater than 10 v, by the ad- dition of one or more external resistors. figure 1 illustrates the general adjustment procedure, with approximate values given for the internal resistors of the ad584. the ad584 may be modeled as an op amp with a noninverting feedback connection, driven by a high stability 1.215 volt bandgap reference (see fig- ure 3 for schematic). when the feedback ratio is adjusted with external resistors, the output amplifier can be made to multiply the reference voltage by almost any convenient amount, making popular outputs of 10.24 v, 5.12 v, 2.56 v or 6.3 v easy to obtain. the most general adjustment (which gives the greatest range and poorest resolution) uses r1 and r2 alone (see figure 1). as r1 is ad- justed to its upper limit the 2.5 v pin 3 will be connected to the output, which will reduce to 2.5 v. as r1 is adjusted to its lower limit, the output voltage will rise to a value limited by r2. for example, if r2 is about 6 k w , the upper limit of the output
ad584 rev. a C5C performance over temperature each ad584 is tested at three temperatures over the C55 c to +125 c range to ensure that each device falls within the maxi- mum error band (see figure 4) specified for a particular grade (i.e., s and t grades); three-point measurement guarantees per- formance within the error band from 0 c to +70 c (i.e., j, k, or l grades). the error band guaranteed for the ad584 is the maximum deviation from the initial value at +25 c. thus, given the grade of the ad584, the designer can easily determine the maximum total error from initial tolerance plus temperature variation. for example, for the ad584t, the initial tolerance is l0 mv and the error band is 15 mv. hence, the unit is guar- anteed to be 10.000 volts 25 mv from C55 c to +125 c. figure 4. typical temperature characteristic output current characteristics the ad584 has the capability to either source or sink current and provide good load regulation in either direction, although it has better characteristics in the source mode (positive current into the load). the circuit is protected for shorts to either posi- tive supply or ground. the output voltage vs. output current characteristics of the device is shown in figure 5. source current is displayed as negative current in the figure; sink current is positive. note that the short circuit current (i.e., zero volts out- put) is about 28 ma; when shorted to +15 volts, the sink cur- rent goes to about 20 ma. figure 5. ad584 output voltage vs. sink and source current dynamic performance many low power instrument manufacturers are becoming in- creasingly concerned with the turn-on characteristics of the components being used in their systems. fast turn-on compo- nents often enable the end user to keep power off when not needed, and yet respond quickly when the power is turned on for operation. figure 6 displays the turn-on characteristic of the ad584. figure 6a is generated from cold-start operation and represents the true turn-on waveform after an extended period with the supplies off. the figure shows both the coarse and fine transient characteristics of the device; the total settling time to within 10 millivolt is about 180 m s, and there is no long ther- mal tail appearing after the point. figure 6. output settling characteristic noise filtering the bandwidth of the output amplifier in the ad584 can be re- duced to filter the output noise. a capacitor ranging between 0.01 m f and 0.1 m f connected between the cap and v bg termi- nals will further reduce the wideband and feedthrough noise in the output of the ad584, as shown in figure 8. however, this will tend to increase the turn-on settling time of the device so ample warm-up time should be allowed. figure 7. additional noise filtering with an external capacitor figure 8. spectral noise density and total rms noise vs. frequency
ad584 rev. a C6C using the strobe terminal the ad584 has a strobe input which can be used to zero the output. this unique feature permits a variety of new applica- tions in signal and power conditioning circuits. figure 9 illustrates the strobe connection. a simple npn switch can be used to translate a ttl logic signal into a strobe of the output. the ad584 operates normally when there is no current drawn from pin 5. bringing this terminal low, to less than 200 mv, will allow the output voltage to go to zero. in this mode the ad584 should not be required to source or sink cur- rent (unless a 0.7 v residual output is permissible). if the ad584 is required to sink a transient current while strobed off, the strobe terminal input current should be limited by a 100 w resistor as shown in figure 9. the strobe terminal will tolerate up to 5 m a leakage and its driver should be capable of sinking 500 m a continuous. a low leakage open collector gate can be used to drive the strobe ter- minal directly, provided the gate can withstand the ad584 out- put voltage plus one volt. figure 9. use of the strobe terminal precision high current supply the ad584 can be easily connected to a power pnp or power darlington pnp device to provide much greater output current capability. the circuit shown in figure 10 delivers a precision 10 volt output with up to 4 amperes supplied to the load. the 0.1 m f capacitor is required only if the load has a significant capacitive component. if the load is purely resistive, improved high frequency supply rejection results from removing the capacitor. figure 10. high current precision supply the ad584 can also use an npn or darlington npn transistor to boost its output current. simply connect the 10 v output ter- minal of the ad584 to the base of the npn booster and take the output from the booster emitter as shown in figure 11. the 5.0 v or 2.5 v pin must connect to the actual output in this con- figuration. variable or adjustable outputs (as shown in figures 1 and 2) may be combined with +5.0 v connection to obtain out- puts above +5.0 v. the ad584 as a current limiter the ad584 represents an alternative to current limiter diodes which require factory selection to achieve a desired current. use of current limiting diodes often results in temperature coeffi- cients of 1%/ c. use of the ad584 in this mode is not limited to a set current limit; it can be programmed from 0.75 ma to 5 ma with the insertion of a single external resistor (see figure 12). of course, the minimum voltage required to drive the con- nection is 5 volts. figure 11. npn output current booster figure 12. a two-component precision current limiter negative reference voltages from an ad584 the ad584 can also be used in a two-terminal zener mode to provide a precision C10 volt, C7.5 volt or C5.0 volt reference. as shown in figure 13, the v in and v out terminals are con- nected together to the positive supply (in this case, ground). the ad584 common pin is connected through a resistor to the negative supply. the output is now taken from the common pin instead of v out . with 1 ma flowing through the ad584 in this mode, a typical unit will show a 2 mv increase in output level over that produced in the three-terminal mode. note also that the effective output impedance in this connection increases from 0.2 w typical to 2 w . it is essential to arrange the output load and the supply resistor, r s , so that the net current through the ad584 is always between 1 ma and 5 ma (between 2 ma and 5 ma for operation beyond +85 c). the temperature character-
ad584 rev. a C7C istics and long-term stability of the device will be essentially the same as that of a unit used in the standard three-terminal mode. figure 13. two-terminal C5 volt reference the ad584 can also be used in a two-terminal mode to develop a positive reference. v in and v out are tied together and to the positive supply through an appropriate supply resistor. the per- formance characteristics will be similar to those of the negative two-terminal connection. the only advantage of this connection over the standard three-terminal connection is that a lower pri- mary supply can be used, as low as 0.5 volts above the desired output voltage. this type of operation will require considerable attention to load and primary supply regulation to be sure the ad584 always remains within its regulating range of 1 ma to 5 ma (2 ma to 5 ma for operation beyond 85 c). 10 volt reference with multiplying cmos d/a or a/d converters the ad584 is ideal for application with the entire ad7520 series of 10- and 12-bit multiplying cmos d/a converters, especially for low power applications. it is equally suitable for the ad7574 8-bit a/d converter. in the standard hook-up as shown in figure 14, the standard output voltages are inverted by the amplifier/dac configuration to produce converted volt- age ranges. for example, a +10 v reference produces a 0 v to C10 v range. if an ad308 amplifier is used, total quiescent sup- ply current will typically be 2 ma. the ad584 will normally be used in the C10 volt mode with the ad7574 to give a 0 volt to +10 volt adc range. this is shown in figure 16. bipolar out- put applications and other operating details can be found in the data sheets for the cmos products. figure 14. low power 10-bit cmos dac application precision d/a converter reference the ad562, like many d/a converters, is designed to operate with a +10 volt reference element (figure 15). in the ad562, this 10 volt reference voltage is converted into a reference cur- rent of approximately 0.5 ma via the internal 19.95 k w resistor (in series with the external 100 w trimmer). the gain tempera- ture coefficient of the ad562 is primarily governed by the tem- perature tracking of the 19.95 k w resistor and the 5k/10k span resistors; this gain t.c. is guaranteed to 3 ppm/ c. thus, using the ad584l (at 5 ppm/ c) as the 10 volt reference guarantees a figure 15. precision 12-bit d/a converter
ad584 rev. a C8C maximum full scale temperature coefficient of 8 ppm/ c over the commercial range. the 10 volt reference also supplies the normal 1 ma bipolar offset current through the 9.95k bipolar offset resistor. the bipolar offset t.c. thus depends only on the t.c. matching of the bipolar offset resistor to the input refer- ence resistor and is guaranteed to 3 ppm/ c. figure 17 demon- strates the flexibility of the ad584 applied to another popular d/a configuration. figure 16. ad584 as negative 10 volt reference for cmos adc figure 17. current output 8-bit d/a c473eC10C6/86 printed in u.s.a. outline dimensions dimensions shown in inches and (mm). to-99 (h) package plastic dip (n) package
|
