View BU18TA2WHFV_2669558.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/29 www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. cmos ldo regulators fo r portable equipments 1ch 200ma cmos ldo regulators bu?? ta2wnvx series, bu ?? ta2whfv series description bu ta2wnvx /hfv series is high-performance full cmos regulator with 200-ma output, which is mounted on microminiature package sson004x1216 (1.2 mm ? 1.6 mm ? 0.6 mm) &hvsof5(1.6mm ? 1.6mm ? 0.6mm). it has excellent noise characteristics and load responsiveness characteri stics despite its low circuit current consumption of 40 a. it is most appropriate for various applications such as power supplies for logic ic, rf, and camera modules. microminiature package sson004x1216 & hvsof5 with built-i n heatsink is adopted for the package, which contributes to the space-saving design of the set. features 1) high-accuracy output voltage of ? 1% ( ? 25 mv on 1.5-v & 1.8-v products 2) high ripple rejection: 70 db (typ., 1 khz, vout ? 1.8 v)) 3) compatible with small ceramic capacitor (c in =co=1.0 f) 4) low current consumption: 40 a 5) on/off control of output voltage 6) with built-in overcurrent protection circuit and overheat protection circuit 7) with built-in output discharge circuit 8) adopting microminiature power package sson004x1216 applications battery-powered portable equipment, etc. line up 200 ma bu ta2wnvx / hfv series product name 1.5 1.8 2.5 2.6 2.7 2 .8 2.85 2.9 3.0 3.1 3.2 3.3 3.4 package bu ta2wnvx sson004x1216 bu ta2whfv hvsof5 model name: bh ta2w a b symbol contents a specification of output voltage output voltage (v) output voltage (v) output voltage (v) 15 1.5v(typ.) 28 2.8v(typ.) 32 3.2v(typ.) 18 1.8v(typ.) 2j 2.85v(typ.) 33 3.3v(typ.) 25 2.5v(typ.) 29 2.9v(typ.) 34 3.4v(typ.) 26 2.6v(typ.) 30 3.0v(typ.) - - 27 2.7v(typ.) 31 3.1v(typ.) - - b package nvx :sson004x1216 hfv :hvsof5 no.11020ect01
technical note 2/29 bu?? ?? ? ? ? ? ? ?
technical note 3/29 bu?? ?? ? ?
technical note 4/29 bu?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. block diagram, recommended circuit diagram, and pin configuration diagram bu ta2wnvx(sson004x1216) pin no. symbol function 1 vout voltage output 2 gnd grounding 3 stby on/off control of output voltage (high: on, low: off) 4 vin power input bu ta2whfv(hvsof5) pin no. symbol function 1 stby on/off control of output voltage (high:on, low:off) 2 gnd grounding 3 vin power input 4 vout voltage output 5 n.c. no connect bh ta2wnvx fig.1 recommended circuit diagram recommended ceramic capacitor for cin & co murata manufacturing co., ltd. grm188b11a105ka61d 12 43 1 2 3 4 5 1 cin vin vin gnd stby vout vout co vref ocp stby discharge vstb y 4/3 2 1/4 3/1
technical note 5/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig.4 stability area characteristics (example) input/output terminal equi valent circui t schematic 1pin (vout) 2pin (gnd) 3pin (stby) 4pin (vin) v in stby fig. input/output equivalent circuit about input/outp ut capacitor it is recommended to place a capaci tor as close as possible to the pins between the input terminal and gnd or between the output terminal and gnd. the capacitor between the input terminal and gnd becomes valid when source impedance increases or when wiring is long. the larger the capacity of the out put capacitor between the output terminal and gnd is, the better t he stability and characteristics in output load fluctuation become. however, please check the status of actual implementation. ce ramic capacitors generally have variation, temperature characteri stics, and direct current bias characteristics and the capacity value also decreases with time depending on the usage conditions. it is recommended to select a ceramic capacitor upon inquiring about detailed data of the related manufacturer. about the equivalent series resistance (esr) of a ceramic capacitor capacitors generally have esr (equivalent series resistance) and it operates stably in the esr-iout area shown on the right. since ceramic capacitors, tantalum capacito rs, electrolytic capacitors, etc. generally have different esr, please check the esr of the capacitor to be used and use it within the stability area range shown in the right graph for evaluati on of the actual application. vout v in fig.3 capacity ? bias characteristics capacity value of ceramic capacitor - dc bias characteristics ( example ) -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 00.511.522.533.54 dc bias voltage [v] capacitance change [%] 10-v withstand voltag e b1char acter istics grm 188b11a105ka61d 10-v withstand voltag e b characteristics 6.3-v withstand voltag e b char acter istics 4-v withstand voltag e x6s characteristics 10-v withstand voltag e f char acter istics 10- v withstand voltag e f char acter istics 0.01 0.1 1 10 100 0 50 100 150 200 iout [ma] esr [ ? ] stability area unstable area
technical note 6/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 5 output voltage fig. 6 line regulation fig. 14 vout vs. temp reference data bu15ta2wnvx / hfv (ta=25oc unless otherwise specified.) fig. 7 circuit current ignd fig. 8 circuit current ignd fig. 9 st by input current fig. 10 iout - ignd fig. 16 ignd vs. temp (stby) fig. 15 ignd vs. temp fig. 11 load regulation fig. 13 stby threshold fig. 12 ocp threshold 0.0 0.3 0.6 0.9 1.2 1.5 1.8 00.511.522.533.544.555.5 vin voltage (v) output voltage (v) io=0ua io=100ua io=50ma io=200ma temp=25c vin = stby 1.45 1.46 1.47 1.48 1.49 1.50 1.51 1.52 1.53 1.54 1.55 1.25 1.35 1.45 1.55 1.65 1.75 1.85 1.95 2.05 2.15 2.25 vin voltage (v) output voltage (v) io=0ua io= 100ua io=50ma io=200ma temp= 25c vin = stby 0 20 40 60 80 100 00.511.522.533.544.555.5 vin voltage (v) gnd current (ua) temp=-40c temp=25c temp=85c io=0ua vin = stby 0 20 40 60 80 100 120 140 00.511.522.533.544.555.5 vin voltage (v) gnd current (ua) io=200ma vin = stby temp=-40c temp=25c temp=85c 0 2 4 6 8 10 00.51 1.522.533.54 4.555.5 stby voltage (v) stby current (ua) vin = stby temp=85c temp=25c temp=- 40c 40 50 60 70 80 90 100 110 120 0 0.05 0.1 0.15 0.2 output current (a) gnd current (ua) vin = 3.5v stby = 1.5v temp=85c temp=25c temp=-40c 1.45 1.46 1.47 1.48 1.49 1.50 1.51 1.52 1.53 1.54 1.55 0 0.05 0.1 0.15 0.2 output current (a) output voltage (v) vin = 3.5v stby = 1.5v temp=-40c temp=25c temp=85c 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 0.00 0.10 0.20 0.30 0.40 0.50 0.60 output current (a) output voltage (v) vin=5.5v temp=25c stby = 1.5v vin=3.5v vin=2.5v 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 0 0.5 1 1.5 stby voltage (v) output voltage (v) temp=85c temp=25c temp=-40c 1.45 1.46 1.47 1.48 1.49 1.50 1.51 1.52 1.53 1.54 1.55 -40 -15 10 35 60 85 temp (c) output voltage (v) vin= 3.5v stby=1.5v io=0.1ma 0.00 10.00 20.00 30.00 40.00 50.00 -40 -15 10 35 60 85 temp ( c) input current (ua) vin=3.5v stby=1.5v io=0ma -0.100 0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 -40 -15 10 35 60 85 temp ( c) gnd current (ua) vin=3.5v stby=0v
technical note 7/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 19 output noise spectral density vs. freq. reference data bu15ta2wnvx /hfv (ta=25oc unless otherwise specified.) fig. 18 ripple rejection vs. vin (iout=10 ma) fig. 17 ripple rejection vs. freq. fig. 24 load response current pulse=10 khz fig. 25 load response current pulse=10 khz fig. 20 load response fig. 21 load response fig. 22 load response fig. 23 load response 0 10 20 30 40 50 60 70 80 0.1 1 10 100 1000 frequency (khz) ripple rejection (db) vin= 3.5v io=10ma ta = 25 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.1 1 10 100 frequency f [khz] output noise density [v/hz] co=1.0f cin=1.0f iout=10ma temp=25 0 10 20 30 40 50 60 70 80 2.5 3.5 4.5 5.5 input voltage vin[v] ripple rejection [db] co=1.0f cin=none iout=10ma temp=25 f=100khz f=10khz f=1khz f =0.1khz
technical note 8/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. reference data bu15ta2wnvx / hfv (ta=25oc unless otherwise specified.) fig. 29 startup time iout = 200 ma fig. 30 startup time (stby=vin) iout = 0 ma fig. 28 startup time iout = 0 ma fig. 32 discharge time iout = 0 ma fig. 33 vin response iout = 10 ma fig. 31 startup time (stby=vin) iout = 200ma fig. 26 load response current pulse=100 khz fig. 27 load response current pulse=100 khz
technical note 9/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 34 output voltage fig. 35 line regulation fig. 43 vout vs temp reference data bu18ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 36 circuit current ignd fig. 38 stby input current fig. 39 iout - ignd fig. 45 ignd vs temp (stby) fig. 44 ignd vs temp fig. 40 load regulation fig. 42 stby threshold fig. 41 ocp threshold fig. 37 circuit current ignd 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 00.511.522.533.544.555.5 vin voltage (v) output voltage (v) io=0ua io= 100ua io=50ma io=200ma temp=25c vin = stby 0 20 40 60 80 100 00.511.522.533.544.555.5 vin voltage (v) gnd current (ua) temp=-40c temp=25c temp=85c io=0ua vin = stby 0 20 40 60 80 100 120 140 00.511.522.533.544.555.5 vin voltage (v) gnd current (ua) io=200ma vin = stby temp=-40c temp=25c temp=85c 0 2 4 6 8 10 00.51 1.522.533.54 4.555.5 stby voltage (v) stby current (ua) vin = stby temp=85c temp=25c temp=-40c 1.75 1.76 1.77 1.78 1.79 1.80 1.81 1.82 1.83 1.84 1.85 0 0.05 0.1 0.15 0.2 output current (a) output voltage (v) vin = 3.5v stby = 1.5v temp=-40c temp=25c temp=85c 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 0.00 0.10 0.20 0.30 0.40 0.50 0.60 output current (a) output voltage (v) vin=5.5v temp=25c stby = 1.5v vin=3.5v vin=2.5v 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 00.5 11.5 stby voltage (v) output voltage (v) temp=85c temp=25c temp=-40c 1.75 1.76 1.77 1.78 1.79 1.80 1.81 1.82 1.83 1.84 1.85 -40 -15 10 35 60 85 temp (c) output voltage (v) vin= 3.5v stby=1.5v io=0.1ma 0.00 10.00 20.00 30.00 40.00 50.00 -40 -15 10 35 60 85 temp (c) input current (ua) vin=3.5v stby=1.5v io=0ma -0.100 0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 -40 -15 10 35 60 85 temp (c) gnd current (ua) vin=3.5v stby=0v 1.75 1.76 1.77 1.78 1.79 1.80 1.81 1.82 1.83 1.84 1.85 1.75 1.85 1.95 2.05 2.15 2.25 2.35 vin voltage (v) output voltage (v) io=0ua io= 100ua io=50ma io=200ma temp=25c vin = stby 40 50 60 70 80 90 100 110 120 0 0.05 0.1 0.15 0.2 output current (a) gnd current (ua) vin = 3.5v stby = 1.5v temp=85c temp=25c temp= - 40c
technical note 10/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 46 ripple rejection vs freq. fig. 47 ripple rejection vs vin fig. 48 output noise spectrl density vs freq. reference data bu18ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 49 load response fig. 51 load response fig. 52 load response fig. 50 load response fig. 53 load response current pulse=10khz fig. 54 load response current pulse=10khz ? 0 10 20 30 40 50 60 70 80 0.1 1 10 100 1000 frequency (khz) ripple rejection (db) vin= 3.5v io=10ma ta = 25 0 10 20 30 40 50 60 70 80 2.5 3.5 4.5 5.5 input voltage vin[v] ripple rejection [db] co=1.0f cin=none iout=10ma temp=25 f=100khz f=10khz f=1khz f=0.1khz 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.1 1 10 100 frequency f [khz] output noise density [v/hz] co=1.0f cin=1.0f iout=10ma temp=25
technical note 11/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. reference data bu18ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 55 load response current pulse=100khz fig. 56 load response current pulse=100khz fig. 57 start up time iout = 0ma fig. 58 start up time iout = 200ma fig. 59 start up time (stby=vin) iout = 0ma fig. 61 discharge time iout = 0ma fig. 62 vin response iout = 10ma fig. 60 start up time(stby=vin) iout = 200ma ?
technical note 12/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 63 output voltage fig. 64 line regulation fig. 72 vout vs temp 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0 0.05 0.1 0.15 0.2 output current (a) dropout voltage (v) vin=0.98*vout stby=1.5v temp.=-40c temp.=25c temp.=85c reference data bu25ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 65 circuit current ignd fig. 67 stby input current fig. 68 iout - ignd fig. 74 ignd vs temp (stby) fig. 73 ignd vs temp fig. 69 load regulation fig. 71 stby threshold fig. 70 ocp threshold fig. 66 dropout voltage 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 00.511.522.533.544.555.5 vin voltage (v) output voltage (v) io=0ua io=100ua io=50ma io=200ma temp.=25c vin=stby 2.45 2.46 2.47 2.48 2.49 2.50 2.51 2.52 2.53 2.54 2.55 2.4 2.5 2.6 2.7 2.8 2.9 3 vin voltage (v) output voltage (v) io=0ua io=100ua io=50ma io=200ma temp.=25c vin=stby 0 20 40 60 80 100 00.511.522.533.544.555.5 vin voltage (v) gnd current (ua) temp.=-40c temp.=25c temp.=85c io=0ua vin=stby 0 2 4 6 8 10 00.51 1.522.533.54 4.555.5 stby voltage (v) stby current (ua) temp.=85c temp.=25c temp.=- 40c 40 50 60 70 80 90 100 110 120 0 0.05 0.1 0.15 0.2 output current (a) gnd current (ua) temp.=85c temp.=25c temp.=-40c 0.00 0.50 1.00 1.50 2.00 2.50 3.00 0 0.1 0.2 0.3 0.4 0.5 0.6 output current (a) output voltage (v) vin=5.5v vin=3.5v vin=3.0v temp.=25c stby=1.5v 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 00.5 11.5 stby voltage (v) output voltage (v) temp.=85c temp.=25c temp.=-40c 2.45 2.46 2.47 2.48 2.49 2.50 2.51 2.52 2.53 2.54 2.55 -40 -15 10 35 60 85 temp. (c) output voltage (v) vin=3.5v stby=1.5v io=0.1ma 0.00 10.00 20.00 30.00 40.00 50.00 -40 -15 10 35 60 85 temp. ( c) gnd current (ua) vin= 3.5v stby=1.5v io=0ma -0.100 0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 -40 -15 10 35 60 85 temp. (c) gnd current (ua) vin=3.5v stby=0v 2.45 2.46 2.47 2.48 2.49 2.50 2.51 2.52 2.53 2.54 2.55 0 0.05 0.1 0.15 0.2 output current (a) output voltage (v) vin=3.5v stby=1.5v temp.=-40c temp.=25c temp.= 85c
technical note 13/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 75 ripple rejection vs freq. fig. 76 ripple rejection vs vin fig. 77 output noise spectrl density vs freq. reference data bu25ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 78 load response fig. 80 load response fig. 81 load response fig. 79 load response fig. 82 load response current pulse=10khz fig. 83 load response current pulse=10khz iout=0ma 100m a iout=100m a 0m a ? ? 0 10 20 30 40 50 60 70 80 0.1 1 10 100 1000 frequency (khz) ripple rejection (db) vin= 3.5v io=10ma ta = 25 0 10 20 30 40 50 60 70 80 2.5 3.5 4.5 5.5 input voltage vin[v] ripple rejection [db] co=1.0f cin=none iout=10ma temp=25 f=100khz f=10khz f =1khz f=0.1khz 0 0.2 0.4 0.6 0.8 1 1.2 0.1 1 10 100 frequency f [khz] output noise density [v/hz] co=1.0f cin=1.0f iout=10ma temp=25
technical note 14/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. reference data bu25ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 84 load response current pulse=100khz fig. 85 load response current pulse=100khz fig. 86 start up time iout = 0ma fig. 87 start up time iout = 200ma fig. 88 start up time (stby=vin) iout = 0ma fig. 90 discharge time iout = 0ma fig. 91 vin response iout = 10ma fig. 89 start up time(stby=vin) iout = 200ma ? ?
technical note 15/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 92 output voltage fig. 93 line regulation fig. 101 vout vs temp reference data bu28ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 94 circuit current ignd fig. 96 stby input current fig. 97 iout - ignd fig. 103 ignd vs temp (stby) fig. 102 ignd vs temp fig. 98 load regulation fig. 100 stby threshold fig. 99 ocp threshold fig. 95 dropout voltage 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 00.511.522.533.544.555.5 vin voltage (v) output voltage (v) temp.=25c io=0ua io= 100ua io=50ma io=200ma vin = stby 2.75 2.76 2.77 2.78 2.79 2.80 2.81 2.82 2.83 2.84 2.85 2.7 2.8 2.9 3 3.1 3.2 vin voltage (v) output voltage (v) temp.=25c io=0ua io=100ua io=50ma io=200ma vin = stby 0 20 40 60 80 100 00.511.522.533.544.555.5 vin voltage (v) gnd current (ua) temp.=-40c temp.=25c temp.=85c io=0ua vin = stby 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0 0.05 0.1 0.15 0.2 output current (a) dropout voltage (v) vi n= 0.98 x vout st by = 1.5v t emp. = -40c temp.=25c temp.=85c 0 2 4 6 8 10 00.511.522.5 33.544.555.5 stby voltage (v) stby current (ua) temp.=85c temp.=25c t emp. = -40c vin = stby 40 50 60 70 80 90 100 110 120 0 0.05 0.1 0.15 0.2 output currnt (a) gnd current (ua) vin = 3.8v stby = 1.5v t emp. = 85c temp.=25c t emp. = -40c 2.75 2.76 2.77 2.78 2.79 2.80 2.81 2.82 2.83 2.84 2.85 0 0.05 0.1 0.15 0.2 output currnt (a) output voltage (v) temp.=-40c temp.=25c temp.=85c vin = 3.8v stby = 1.5v 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 0 0.1 0.2 0.3 0.4 0.5 0.6 output current (a) output voltage (v) vin=5.5v stby = 1.5v vin=3.8v vin=3.3v temp=25c 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 00.5 11.5 stby voltage (v) output voltage (v) vin=3.8v temp.=85c temp.=25c temp.=-40c 2.75 2.76 2.77 2.78 2.79 2.80 2.81 2.82 2.83 2.84 2.85 -40 -15 10 35 60 85 temp. (c) output voltage (v) vin= 3.8v stby=1.5v io=0.1ma 0.00 10.00 20.00 30.00 40.00 50.00 -40 -15 10 35 60 85 temp. ( c) gnd current (ua) vin=3.8v stby=1.5v io=0ma -0.100 0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 -40 -15 10 35 60 85 temp. (c) gnd current (ua) vin= 3.8v stby=0v
technical note 16/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 104 ripple rejection vs freq. fig. 105 ripple rejection vs vin fig. 106 output noise spectrl density vs freq. reference data bu28ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 107 load response fig.109 load response fig. 110 load response fig. 108 load response fig. 111 load response current pulse=10khz fig. 112 load response current pulse=10khz ? ? 0 10 20 30 40 50 60 70 80 0.1 1 10 100 1000 frequency (khz) ripple rejection (db) vin= 3.8v io=10ma ta = 25 0 10 20 30 40 50 60 70 80 2.8 3.8 4.8 input voltage vin[v] ripple rejection [db] f=100khz f=10khz f=1khz f=0.1khz co=1.0f cin=none iout=10ma temp=25 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 0.1 1 10 100 frequency f [khz] output noise density [v/hz] co=1.0f cin=1.0f iout=10ma temp=25
technical note 17/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. reference data bu28ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 113 load response current pulse=100khz fig. 114 load response current pulse=100khz fig. 115 start up time iout = 0ma fig. 116 start up time iout = 200ma fig. 117 start up time (stby=vin) iout = 0ma fig. 119 discharge time iout = 0ma fig.120 vin response iout = 10ma fig. 118 start up time(stby=vin) iout = 200ma ? ?
technical note 18/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 121 output voltage fig. 122 line regulation fig. 130 vout vs temp reference data bu30ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 123 circuit current ignd fig. 125 stby input current fig. 126 iout - ignd fig. 132 ignd vs temp (stby) fig. 131 ignd vs temp fig. 127 load regulation fig. 129 stby threshold fig.128 ocp threshold fig. 124 dropout voltage 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 00.511.522.533.544.555.5 vin voltage (v) output voltage (v) temp.=25c io=0ua io=100ua io=50ma io=200ma vin=stby 2.95 2.96 2.97 2.98 2.99 3.00 3.01 3.02 3.03 3.04 3.05 2.9 3 3.1 3.2 3.3 3.4 3.5 vin voltage (v) output voltage (v) temp.=25c io=0ua io=100ua io=50ma io=200ma vin=stb y 0 20 40 60 80 100 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 vin voltage (v) gnd current (ua) io=0ua temp.=- 40c temp.=25c temp.=85c vin=stby 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0 0.05 0.1 0.15 0.2 output current (a) dropout voltage (v) vin= 0.98*vout stby=1.5v temp.=-40c temp.= 25c temp.=85c 0 2 4 6 8 10 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 stby voltage (v) stby current (ua) temp.=85c temp.=25c temp.=- 40c vin=stby 40 50 60 70 80 90 100 110 120 0 0.05 0.1 0.15 0.2 output current (a) gnd current (ua) temp.=85c temp.=25c temp=-40c 2.95 2.96 2.97 2.98 2.99 3.00 3.01 3.02 3.03 3.04 3.05 0 0.05 0.1 0.15 0.2 output current (a) output voltage (v) vin=4.0v stby=1.5v temp.=-40c temp.=25c temp.=85c 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 0 0.1 0.2 0.3 0.4 0.5 0.6 output current (a) output voltage (v) vin=5.5v vin=4.0v vin=3.5v temp.=25c stby=1.5v 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 00.5 11.5 stby voltage (v) output voltage (v) vin = 4.0v temp.=85c temp.=25c temp.=-40c 2.95 2.96 2.97 2.98 2.99 3.00 3.01 3.02 3.03 3.04 3.05 -40 -15 10 35 60 85 temp. (c) output voltage (v) vin=4.0v stby=1.5v io=0.1ma 0.00 10.00 20.00 30.00 40.00 50.00 -40 -15 10 35 60 85 temp. ( c) input current (a) vin= 4.0v stby=1.5v io=0ma -0.100 0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 -40 -15 10 35 60 85 temp. ( c) input current (a) vin=4.0v stby=0v io=0ma
technical note 19/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 133 ripple rejection vs freq. fig. 134 ripple rejection vs vin fig. 135 output noise spectrl density vs freq. reference data bu30ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 136 load response fig. 138 load response fig. 139 load response fig. 137 load response fig. 140 load response current pulse=10khz fig. 141 load response current pulse=10khz 0 10 20 30 40 50 60 70 80 0.1 1 10 100 1000 frequency (khz) ripple rejection (db) vin= 4.0v io=10ma ta = 25 0 10 20 30 40 50 60 70 80 345 input voltage vin[v] ripple rejection [db] f=100khz f=10khz f=1khz f=0.1khz co=1.0f cin=none iout=10ma temp=25 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 0.1 1 10 100 frequency f [khz] output noise density [v/hz] co=1.0f cin=1.0f iout=10ma temp=25
technical note 20/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. reference data bu30ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 142 load response current pulse=100khz fig. 143 load response current pulse=100khz fig. 144 start up time iout = 0ma fig. 145 start up time iout = 200ma fig. 146 start up time (stby=vin) iout = 0ma fig. 148 discharge time iout = 0ma fig. 149 vin response iout = 10ma fig. 147 start up time(stby=vin) iout = 200ma
technical note 21/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 150 output voltage fig. 151 line regulation fig. 159 vout vs temp reference data bu33ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 152 circuit current ignd fig. 154 stby input current fig. 155 iout - ignd fig. 161 ignd vs temp (stby) fig. 160 ignd vs temp fig. 156 load regulation fig. 158 stby threshold fig. 157 ocp threshold fig. 153 dropout voltage 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 00.511.522.533.544.555.5 vin voltage (v) output voltage (v) io=0ua io=100ua io=50ma io=200ma temp.=25c vin = stby 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 3.2 3.3 3.4 3.5 3.6 3.7 vin voltage (v) output voltage (v) io=0ua io=100ua io=50ma io=200ma temp=25c vin = stby 0 20 40 60 80 100 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 vin voltage (v) gnd current (ua) temp.=-40c temp.=25c temp.=85c io=0ua vin = stby 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0 0.05 0.1 0.15 0.2 output current (a) dropout voltage (v) vin=0.98 x vout stby = 1.5v temp.=-40c temp.=25c temp.=85c 0 2 4 6 8 10 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 v stby voltage (v) stby current (ua) vin = stby temp.=85c temp.=25c temp.=-40c 40 50 60 70 80 90 100 110 120 0 0.05 0.1 0.15 0.2 output current (a) gnd current (ua) vin = 4.3v stby = 1.5v temp.=85c temp.=25c temp.=-40c 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 0 0.05 0.1 0.15 0.2 output current (a) output voltage (v) vin = 4.3v stby = 1.5v temp.=-40c temp.=25c temp.=85c 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 0 0.1 0.2 0.3 0.4 0.5 0.6 output current (a) output voltage (v) vin=5.5v stby = 1.5v temp=25 vin=4.3v vin=3.8v 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 00.5 11.5 stby voltage (v) output voltage (v) vin= 4.3v temp.=85c temp.=25c temp.=-40c 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 -40 -15 10 35 60 85 temp. (c) output voltage (v) vin= 4.3v stby=1.5v io=0.1ma 0.00 10.00 20.00 30.00 40.00 50.00 -40 -15 10 35 60 85 temp. ( c) gnd current (ua) vin=4.3v stby=1.5v io=0ma -0.100 0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 -40 -15 10 35 60 85 temp. ( c) gnd current (ua) vin=4.3v stby=0v
technical note 22/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. fig. 162 ripple rejection vs freq. fig. 163 ripple rejection vs vin fig. 164 output noise spectrl density vs freq. reference data bu33ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 165 load response fig. 167 load response fig. 168 load response fig. 166 load response fig. 169 load response current pulse=10khz fig. 170 load response current pulse=10khz 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 0.1 1 10 100 frequency f [khz] o utput noise density [ v/ hz] co=1.0f cin=1.0f iout=10ma temp=25 0 10 20 30 40 50 60 70 80 3.3 4.3 5.3 input voltage vin[v] ripple rejection [db] f=100khz f=10khz f=1khz f=0.1khz co=1.0f cin=none iout=10ma temp=25 0 10 20 30 40 50 60 70 80 0.1 1 10 100 1000 frequency (khz) ripple rejection (db) vin= 4.3v io=10ma ta = 25
technical note 23/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. reference data bu33ta2wnvx / hfv (unless otherwise specified, ta=25 ) fig. 171 load response current pulse=100khz fig. 172 load response current pulse=100khz fig. 173 start up time iout = 0ma fig. 174 start up time iout = 200ma fig. 175 start up time (stby=vin) iout = 0ma fig. 177 discharge time iout = 0ma fig. 178 vin response iout = 10ma fig. 176 start up time(stby=vin) iout = 200ma
technical note 24/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. about power dissipation (pd) as for power dissipation, an approximate es timate of the heat reduction characteri stics and internal power consumption of ic are shown, so please use these for reference. since power dissipation changes substantially depending on the implementation conditions (board size, board thickness, metal wiring rate, number of layers and through holes, etc.), it is recommended to measure pd on a set board. exceeding the power dissipation of ic may lead to deterioration of the original ic performance, such as causing operation of the thermal shutdown circuit or reducti on in current capability. therefore, be sure to prepare sufficient margin within power dissipation for usage. calculation of the maximum inter nal power consumption of ic (p max ) p max =(v in -v out )i out (max.) (v in : input voltage v out : output voltage i out (max): maximum output current) measurement conditions evaluation board 1 (single-side board) evaluation board 2 (double-side board) layout of board for measurement (unit: mm) ic implementation position top layer (top view) top layer (top view) bottom layer (top view) bottom layer (top view) measurement state with board implemented (wind speed 0 m/s) with board implemented (wind speed 0 m/s) board material glass epoxy resin (single-side board) glass epoxy resin (double-side board) board size 40 mm x 40 mm x 0.8 mm 40 mm x 40 mm x 0.8 mm wiring rate top layer metal (gnd) wiring rate: approx. 25% metal (gnd) wiring rate: approx. 25% bottom layer metal (gnd) wiring rate: approx 0% metal (gnd) wiring rate: approx 25% through hole 0 holes diameter 0.5 mm ? 12 holes power dissipation 1100 mw 1250 mw thermal resistance ja=91 /w ja=80 /w 40 20 40 20 40 40 20 40 20 40 20 40 20 40
technical note 25/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. sson004x1216 hvsof5 * please design the margin so that p max becomes is than pd (p max ? pd) within the usage temperature range. - standard rohm board - size: 70 mm ? 70 mm ? 1.6 mm material: glass epoxy board 0 500 1000 1500 0 25 50 75 100 125 ta ( ) pd (mw) evaluation board 2 (double-side board) evaluation board 1 (single-side board) standard rohm board 1250 mw 1100 mw 220 mw fig.179 sson004x1216 power dissipation heat reduction characteristics (reference) fig.180 hvsof5 power dissipation heat reduction characteristics (reference) * please design the margin so that p max becomes is than pd (p max ? pd) within the usage temperature range. pdw)
technical note 26/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. device type & mark a xx output voltage package sson004x1216 hvsof5 15 1.5v typ. aa ba 18 1.8v typ. ab bb 25 2.5v typ. ac bd 26 2.6v typ. ad be 27 2.7v typ. ae bf 28 2.8v typ. af bg 2j 2.85v typ. ag bh 29 2.9v typ. ah bj 30 3.0v typ. aj bk 31 3.1v typ. ak bl 32 3.2v typ. al bm 33 3.3v typ. am bn 34 3.4v typ. an bp device type : buxx ta2wnvx a device type : buxx ta2whfv a sson004x1216 hvsof5
technical note 27/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. sson004x1216 hvsof5 m a rk lot no. mark lot no.
technical note 28/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. notes for use ? about absolute maximum rating breakage may occur when absolute maximum ratings such as applied voltage and operating temperature range are exceeded. short mode or open mode cannot be specified at o ccurrence of a break, so please prepare physical safety measures (e.g., fuse) if such special mode in which the absolute maximum rating is exceeded can be assumed. ? about gnd potential please be sure that the potential of the gnd terminal is the lowest in any operating condition. ? about thermal design please provide thermal design with sufficient margin, taking power dissipation (pd) in actual usage conditions into consideration. ? about short between pins and misattachment please be careful regarding the ic direction and misalignment at attachment onto a printed ci rcuit board. misattachment may cause a break of ic. short caused by foreign matter be tween outputs, output and power supply, or gnds may also lead to a break. ? about operation in a strong electromagnetic field please note that usage in a strong electr omagnetic field may cause malfunction. ? about common impedance please give due consideration to wiring of the power sour ce and gnd by reducing common-mode ripple or making ripple as small as possible (e.g., making the wiring as thick and short as possible, or reducing ripple by l ? c), etc. ? about stby terminal voltage set stby terminal voltage to 0.3 v or less to put each channel into a standby state and to 1.5 v or more to put each channel into an operating state. do not fix stby terminal voltage to 0.3 v or more and 1.5 v or less or do not lengthen the transition time. this may cause malf unction or failure. when shorting the vin terminal and stby terminal for usage, the status will be ?stby=vin low? at turning the power off, and dischar ge of the vout terminal cannot operate, which means voltage may remain for a certain time in the vo ut terminal. since turning the power on again in this state may cause overshoot, turn the power on for use af ter the vout terminal is completely discharged. ? about overcurrent protection circuit output has a built-in overcurrent protection circuit, which prevents ic break at load short. note that this protection circuit is effective for prevention of breaks due to unexpected accidents. please avoid us age by which the protection circuit operates continuously. ? about thermal shutdown output is off when the thermal circuit operates since a tem perature protection circuit is built in to prevent thermal breakdown. however, it recovers when the temperature returns to a certain temperature. the thermal circuit operates at emergency such as overheating of ic. sinc e it is prepared to prevent ic breakdown, please do not use it in a state in which protection works. about reverse current for applications on which reverse current is assumed to flow into ic, it is recommended to prepare a path to let the current out by putting a bypass diode between the v in -v out terminals. about testing on a set board when connecting a capacitor to a terminal with low impedance for testing on a set board, please be sure to discharge for each process since ic may be stressed. as a countermeasure against static electricit y, prepare grounding in the assembly process and take sufficient care in transportation and storage. in addition, when connecting a capacitor to a jig in a testing process, please do so after turning the power off and remove it after turning the power off. fig.181 example of bypass diode connection reverse current vin gnd stby out
technical note 29/29 bu ?? ta2wnvx series, bu ?? ta2whfv series www.rohm.com 2011.01 - rev.c ? 2011 rohm co., ltd. all rights reserved. ordering part number b u 1 5 t a 2 w n v x - t r part no. output voltage lineup shutdown swich w : includes switch package nvx : sson004x1216 hfv : hvsof5 packaging and forming specification tr: embossed tape and reel 15: 1.5v 18: 1.8v 25: 2.5v 26: 2.6v 27: 2.7v 28: 2.8v 2j: 2.85v 29: 2.9v 30: 3.0v 31: 3.1v 32: 3.2v 33: 3.3v 34: 3.4v (unit : mm) sson004x1216 s 0.08 s 3 4 2 1 1pin mark 1.2 0.1 0.65 0.1 0.75 0.1 1.6 0.1 0.2 0.1 0.8 0.1 0.6max (0.12) 0.02 +0.03 - 0.02 0.2 +0.05 - 0.04 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand 5000pcs tr () direction of feed reel 1pin (unit : mm) hvsof5 s 0.08 m 0.1 s 4 3 2 1 5 (0.05) 1.6 0.05 1.0 0.05 1.6 0.05 1.2 0.05 (max 1.28 include burr) 45 32 1 (0.8) (0.91) (0.3) (0.41) 0.2max 0.13 0.05 0.22 0.05 0.6max 0.5 0.02 +0.03 ?0.02 direction of feed reel ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand 3000pcs tr () 1pin
r1120 a www.rohm.com ? 2011 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes no copying or reproduction of this document, in part or in whole, is permitted without the consent of rohm co.,ltd. the content specied herein is subject to change for improvement without notice. the content specied herein is for the purpose of introducing rohm's products (hereinafter "products"). if you wish to use any such product, please be sure to refer to the specications, which can be obtained from rohm upon request. examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. great care was taken in ensuring the accuracy of the information specied in this document. however, should you incur any damage arising from any inaccuracy or misprint of such information, rohm shall bear no responsibility for such damage. the technical information specied herein is intended only to show the typical functions of and examples of application circuits for the produc ts. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm and other parties. rohm shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. the products specied in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, ofce-automation equipment, commu- nication devices, electronic appliances and amusement devices). the products specied in this document are not designed to be radiation tolerant. while rohm always makes efforts to enhance the quality and reliability of its products, a product may fail or malfunction for a variety of reasons. please be sure to implement in your equipment using the products safety measures to guard against the possibility of physical injury, re or any other damage caused in the event of the failure of any product, such as derating, redundancy, re control and fail-safe designs. rohm shall bear no responsibility whatsoever for your use of any product outside of the prescribed scope or not in accordance with the instruction manual. the products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel- controller or other safety device). rohm shall bear no responsibility in any way for use of any of the products for the above special purposes. if a product is intended to be used for any such special purpose, please contact a rohm sales representative before purchasing. if you intend to export or ship overseas any product or technology specied herein that may be controlled under the foreign exchange and the foreign trade law, you will be required to obtain a license or permit under the law.

▲Up To Search▲

Price & Availability of BU18TA2WHFV

	To Download BU18TA2WHFV Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .