View P645HW01V0_2508051.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 2/32 2008 all rights reserved no reproduction and redistribution allowed rev.1.1 date: 2009/01/16 product functional specification 65" full hd color tft-lcd module model name: p645hw01 v0 () preliminary specification (*) final specification note: this specification is subject to change witho ut notice. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 3/32 2008 all rights reserved no reproduction and redistribution allowed contents no contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specification 3.1 signal electriacl characteristics 3.2 signal interface connector 3.3 signal timing specification 3.4 signal timing waveform 3.5 color input data reference 3.6 back light power specification 3.7 power sequence 4 optical specification 5 mechanical characteristics 6 packing 7 reliability test 8 international standard 9 precautions www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 4/32 2008 all rights reserved no reproduction and redistribution allowed record of revision rev. data page items new description remark 0.1 2008/04/08 -- first release n/a 0.2 2008/09/04 all model name g645hw01 v0 p645hw01 v0 5 general information update tbd items 7 signal electrical characteristics update tbd it ems 12 signal timing specification update timing tabl e 15 backlight power specification update electrica l specification 19 power sequence update the sequence table 21 optical specification update tbd items 24, 25 2d drawing update 2d drawing 26~28 packing update: package information pallet information panel label carton label 29 reliability test update: vibration test drop test 1.0 2009/01/16 6 wet bulb figure correct the boundary 12 timing table (de only mode) update all min. data 15 backlight power specification update electrical spe cification max i ddb : 17.5a 17 truth table revise the definition of fb1, fb2 21 optical specification contrast ratio 2000 2500 24, 25 2d drawing update 2d drawing 1.1 2009/02/23 25 2d drawing update 2d drawing (rear) 28 panel label update panel label www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 5/32 2008 all rights reserved no reproduction and redistribution allowed 1. general description this specification applies to the 65 inch color tft -lcd module p645hw01 v0. this lcd module has a tft active matrix type liquid crystal panel 1920x1080 p ixels, and diagonal size of 64.5 inch. this module supports full hd mode (non-interlace). each pixel is divided into red, green, and blue sub -pixels or dots which are arranged in vertical stri pes. gray scale or the brightness of the sub-pixel color is d etermined by 10-bit gray scale signal for each dot. the p645hw01 v0 has been designed to apply the 10-b it 2-channel lvds interface method. it is intended to support displays where high brightness, wide viewin g angle, and high color depth are important. the p645hw01 v0 is rohs verified which can be disti nguished on panel label. general information items specification unit note active screen size 64.53 inches diagonal display area 1428.48 (h) x 803.52 (v) mm outline dimension 1482.4( v h www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 6/32 2008 all rights reserved no reproduction and redistribution allowed 2. absolute maximum ratings the followings are maximum values which, if exceede d, may cause faulty operation or damage to the unit : item symbol min. max unit note logic/lcd drive voltage v cc -0.3 +14.0 v [1] input voltage of signal v in -0.3 +4.0 v [1] blu input voltage v ddb -0.3 +27.0 v [1] blu brightness control voltage v blon -0.3 +7.0 v [1] operating temperature t op 0 +50 c [2] operating humidity h op 10 90 %rh [2] storage temperature t st -20 +60 c [2] storage humidity h st 10 90 %rh [2] panel surface temperature t sur -- +65 c [2] open lamp feedback voltage vfb -0.3 +3.6 v note [1]: if operate over spec but under absolute m aximum rating, duration must be < 50ms. note [2]: maximum wet-bulb should be 39c and no co ndensation. the relative humidity must not exceed 80% non-condensing at temperatures of 40c o r less. at temperatures greater than 40c, the wet bulb temperature must not exceed 39c . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 7/32 2008 all rights reserved no reproduction and redistribution allowed 3. electrical specification the p645hw01 v0 requires two power inputs. one is e mployed to power the lcd electronics and to drive t he tft array and liquid crystal. the second input is t o power the inverter, which can power the ccfl. 3.1 signal electrical characteristics (ta = 25 2c) value parameter symbol min. typ. max unit note power supply input voltage v cc 10.8 12.0 13.2 v power supply input current i cc 2.0 a [2] power consumption p cc 24.0 watt [2] inrush current i rush -- -- 4.0 a [3] differential input high threshold voltage v th -- -- +100.0 mv [4] differential input low threshold voltage v tl -100.0 -- -- mv [4] lvds interface common input voltage v cim 1.10 1.25 1.40 v input high threshold voltage v ih (high) 2.4 -- 3.3 v cmos interface input low threshold voltage v il (low) 0 -- 0.7 v note: 1. the check pattern is base on white pattern. the rip ple voltage should be controlled under 10% of v cc . 2. v cc = 12.0v, f v = 60hz, f clk = 74.58mhz, 25c, v cc duration time = 470s, test pattern: full white pa ttern 3. measurement condition: rising time=470 www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 8/32 2008 all rights reserved no reproduction and redistribution allowed 4. measurement of lvds differential voltage is shown a s following: vth vcim vtl 0v 5. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module has a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 9/32 2008 all rights reserved no reproduction and redistribution allowed 3.2 signal interface connections lcd lvds connector (51pin): jae fi-re51s-hf pin # signal name description note 1 vcc operating voltage supply, +12v dc regulated 2 vcc operating voltage supply, +12v dc regulated 3 vcc operating voltage supply, +12v dc regulated 4 vcc operating voltage supply, +12v dc regulated 5 vcc operating voltage supply, +12v dc regulated 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground power 10 r1_0- lvds channel 1, signal 0- 11 r1_0+ lvds channel 1, signal 0+ 12 r1_1- lvds channel 1, signal 1- 13 r1_1+ lvds channel 1, signal 1+ 14 r1_2- lvds channel 1, signal 2- 15 r1_2+ lvds channel 1, signal 2+ 16 gnd ground 17 r1_clk- lvds channel 1, clock - 18 r1_clk+ lvds channel 1, clock + 19 gnd ground 20 r1_3- lvds channel 1, signal 3- 21 r1_3+ lvds channel 1, signal 3+ 22 r1_4- lvds channel 1, signal 4- 23 r1_4+ lvds channel 1, signal 4+ 24 gnd ground lvds channel 1 25 r2_0- lvds channel 2, signal 0- 26 r2_0+ lvds channel 2, signal 0+ 27 r2_1- lvds channel 2, signal 1- 28 r2_1+ lvds channel 2, signal 1+ 29 r2_2- lvds channel 2, signal 2- 30 r2_2+ lvds channel 2, signal 2+ 31 gnd ground 32 r2_clk- lvds channel 2, clock - 33 r2_clk+ lvds channel 2, clock + 34 gnd ground 35 r2_3- lvds channel 2, signal 3- lvds channel 2 www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 10/32 2008 all rights reserved no reproduction and redistribution allowed 36 r2_3+ lvds channel 2, signal 3+ 37 r2_4- lvds channel 2, signal 4- 38 r2_4+ lvds channel 2, signal 4+ 39 gnd ground 40 nc no connect (auo internal use only) 41 nc no connect (auo internal use only) 42 nc no connect (auo internal use only) 43 nc no connect (auo internal use only) 44 nc no connect (auo internal use only) 45 lvds_sel open/high(3.3v) for ns, low(gnd) for je ida default: ns 46 nc no connect (auo internal use only) 47 nc no connect (auo internal use only) 48 nc no connect (auo internal use only) 49 nc no connect (auo internal use only) 50 nc no connect (auo internal use only) 51 nc no connect (auo internal use only) note [1]: all gnd (ground) pins should be connected together and should also be connected to the lcd?s metal frame. note [2]: all v cc (power input) pins should be connected together. note [3]: all nc (no connection) pins should be ope n without voltage input. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 11/32 2008 all rights reserved no reproduction and redistribution allowed lvds_sel= open/high(3.3v) ns rx_clk+ rx_clk- rx_0+ rx_0- rx_1+ rx_1- rx_2+ rx_2- rx_3+ rx_3- rx_4+ rx_4- g0 r5 r4 r3 r2 r1 r0 r0 g0 b1 b0 g5 g4 g3 g2 g1 g1 b1 de vs hs b5 b4 b3 b2 b2 de na b7 b6 g7 g6 r7 r6 r6 na na b9 b8 g9 g8 r9 r8 r8 na current cycle next cycle previous cycle (x=1~2) lvds_sel = low(gnd) jeida rx_clk+ rx_clk- rx_0+ rx_0- rx_1+ rx_1- rx_2+ rx_2- rx_3+ rx_3- rx_4+ rx_4- g4 r9 r8 r7 r6 r5 r4 r4 g4 b5 b4 g9 g8 g7 g6 g5 g5 b5 de vs hs b9 b8 b7 b6 b6 de na b3 b2 g3 g2 r3 r2 r2 na na b1 b0 g1 g0 r1 r0 r0 na current cycle next cycle previous cycle (x=1~2) www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 12/32 2008 all rights reserved no reproduction and redistribution allowed 3.3 signal timing specification this is the signal timing required at the input of the user connector. all of the interface signal tim ing should be satisfied with the following specifications for its proper operation. timing table (de only mode) signal item symbol min. typ. max unit period t v 1120 1130 1135 t h active t disp (v) 1080 vertical section blanking t blk (v) 40 50 55 t h period t h 1050 1100 1110 t clk active t disp (h) 960 horizontal section blanking t blk (h) 90 140 150 t clk period tclk 18.09 13.41 12.61 ns clock frequency f clk 55.27 74.58 79.37 mhz vertical frequency frequency f v 47 60 63 hz horizontal frequency frequency f h 52.64 67.8 71.51 khz note [1]: display position is specific by the rise of de signal only. horizontal display position is specified by the fal ling edge of 1st dclk right after the rise of de, is displayed on the left edge of the screen. vertical display position is specified by the rise of de after a ?low? level period equivalent to eight times of horizontal period. the 1st data corr esponding to one horizontal line after the rise of enab is displayed at the top line of screen . note [2]: if a period of de ?high? is less than 192 0 dclk or less than 1080 lines, the rest of the screen displays black. note [3]: the display position does not fit to the screen if a period of de ?high? and the effective d ata period do not synchronize with each other. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 13/32 2008 all rights reserved no reproduction and redistribution allowed 3.4 signal timing waveform www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 14/32 2008 all rights reserved no reproduction and redistribution allowed 3.5 color input data reference the brightness of each primary color (red, green, a nd blue) is based on the 10-bit gray scale data inp ut for the color; the higher the binary input, the brighter th e color. the table below provides a reference for c olor versus data input. color data reference input color data red green blue msb lsb msb lsb msb lsb color r9 r8 r7 r6 r5 r4 r3 r2 r1 r0 g9 g8 g7 g6 g5 g4 g3 g2 g1 g0 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : red(254) 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(255) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 : green(254) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 green green(255) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 : blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 blue blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 15/32 2008 all rights reserved no reproduction and redistribution allowed 3.6 backlight power specification electrical specification (ta=255 o c, turn-on after 60mins, v ddb =24v) specification item symbol min. typ. max unit note 1 input voltage v ddb 21.6 24.0 26.4 v 2 input current i ddb -- 16.5 17.5 a [1] 3 input power p ddb -- 396 watt [1] 4 inrush current i dd_rush -- -- 24 a [2] 5 output frequency f bl 42 khz on 2.0 3.3 5.0 v 6 on/off control voltage v blon off 0 -- 0.8 v 7 on/off control current i blon 0 -- 2.0 ma max 3 -- 3.3 v 8 dimming control voltage v dim min 0 -- 0.8 v 9 dimming control current i dim 0 -- 2.0 ma 10 dimming frequency f dim 180 hz max 3.3 v 11 external pwm control voltage v epwm min 0 v 12 external pwm control current i epwm 0 -- 2.0 ma 13 external pwm duty ratio d epwm 30 -- 100 % [3] 14 external pwm frequency f epwm 180 hz h 2.0 -- 3.3 v 15 feedback signal voltage fb1, fb2 l 0 -- 0.8 v note [1]: the specification value is under v dim = 3.3v, epwm = open or high note [2]: measurement condition: rising time = 20ms (v ddb : 10% 90%) note [3]: if operation below 20% dimming duty, (a) function is okay and no backlight shut down, (b) uniformity, lifetime, and flicker do not guaran tee. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 16/32 2008 all rights reserved no reproduction and redistribution allowed inverter interface connection cn1 of master board: s14b-ph-sm3-tb (jst) or compatible pinzfz symbolz descriptionz 1z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 2z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 3z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 4z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 5z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 6z gndz groundz 7z gndz groundz 8z gndz groundz 9z gndz groundz 10z gndz groundz 11z ncz nozconnectz(auozinternalzusezonly)z 12z v blon z backlightzon/off:z open/high(+3.3v)zforzblzon,zlow(gnd)zforzblzoffz 13z pdim z[1] z external pwm dimming control input: open/high (3.3v/100% duty) for 100% lum internal pwm: open/high%b3.3v/100i%dutyc%for%100i%lum;%gnd%for%30 i% 14% pdim% % selection %[2] % high (3.3v): internal pwm dimming low%bgndc/open:%external%pwm%dimming% % note%[1]:%pdim%is%pwm%duty%control%input%for%[3.3v% ttl%level%signal.%this%input%signal%is% continuous%pulse%signal%with%[3.3v]%ttl%level%signa l%spec.%if%this%is%open%or%[3.3v]%100i% duty%bi.e.%[3.3v]%dc%levelc]%back%light%should%perf orm%100i%luminance.% % duty%ratio%of% this%input%signal%should%be%proportional%relationsh ip%in%certain%range%of%control%without%any% www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 17/32 2008 all rights reserved no reproduction and redistribution allowed kind of inherent side effect like waterfall effect on screen. guaranteed duty range and dimming ratio should be specified with supplementar y measurement result. note [2]: 14 pin is selection pin for back light di mming control method; if this pin is connected to open/low(gnd) pdim input of 13th pin should have logic level dut y signal for pwm duty control. if this pin is connected to high (3.3v) pdim input of 13th pin should have external voltag e to control (3.3v/100% duty gnd/30%duty). cn10 of master board: s3b-zr-sm3a-tf (jst) z notez[1]:z lamp status feedback signal: % % truth%table% lamp%status% bfb1%]%fb2c% normal% bl%]%lc% 1%lamp%open% bh%]%lc% 2~3%lamps%open% bl%]%hc% shut%down% bh%]%hc% %% % % % pin%no% symbol % description% note% 1% fb1% feedback%pin%1%bsensor%open%lamp%signalc% [1] % 2% fb2% feedback%pin%2%bsensor%open%lamp%signalc% [1] % 3% gnd% ground% % lamps % mcu% slaver%1 % mcu% master% mcu% slaver%2 % ??? % ??? % ??? % fb1 % fb2% www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 18/32 2008 all rights reserved no reproduction and redistribution allowed cn1 of slaver board: s12b-ph-sm3-tb (jst) or compatible z pinzfz symbolz descriptionz 1z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 2z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 3z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 4z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 5z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 6z v ddb z operatingzvoltagezsupply,z+24vzdczregulatedz 7z gndz groundz 8z gndz groundz 9z gndz groundz 10z gndz groundz 11z gndz groundz 12z gndz groundz z notez[1]:zallzgndz(ground)zpinszforzeachzconnectorz shouldzbezconnectedztogetherzandzshouldzalsozbez connectedztozthezlcd?szmetalzframe.z notez[2]:zallzv ddb z(powerzinput)zpinszforzeachzconnectorzshouldzbezco nnectedztogether.z z zz www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 19/32 2008 all rights reserved no reproduction and redistribution allowed 3.7 power sequence power sequence of lcd 10% 90% 90% 10% t1 t2 t3 t4 t5 t6 t7 lamp on valid data power supply for lcd signal backlight values parameter min. typ. max. unit t1 0.5 -- 30 ms t2 5 -- 50 ms t3 500 -- -- ms t4 100 -- -- ms t5 5 -- 50 ms t6 -- -- 30 ms t7 1000 -- -- ms note [1]: apply the lamp voltage within the lcd ope rating range. when the backlight turns on before the lcd operation or the lcd turns off before the b acklight turns off, the display may momentarily become abnormal. caution : the above on/off sequence should be applied to av oid abnormal function in the display. in case of handling, make sure to turn off the power w hen you plug the cable into the input connector or pull the cable out of the connector. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 20/32 2008 all rights reserved no reproduction and redistribution allowed power sequence of inverter values parameter min. typ. max. unit t1 20 -- -- ms t2 500 -- -- ms t3 250 -- -- ms t4 0 -- -- ms t5 1 -- 50 ms t6 -- -- 10 ms www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 21/32 2008 all rights reserved no reproduction and redistribution allowed 4. optical specification optical characteristics are determined after the un it has been ?on? and stable for approximately 60 mi nutes in a dark environment at 25c. the values specified are at an approximate distance 50cm from the lcd surfac e at a viewing angle of and equal to 0. test condition: (ta=255 o c, turn-on after 60mins) values parameter symbol min. typ. max unit notes contrast ratio cr 2000 2500 -- [1], [2] surface luminance (white) l wh 550 700 -- cd/m 2 [1], [3] luminance variation white(9p) -- -- 1.3 [4] response time (average) t r -- 8 -- ms [1],[5] (gray to gray) color coordinates (cie 1931) red r x 0.64 [1] r y 0.33 [1] green g x 0.29 [1] g y 0.60 [1] blue b x 0.15 [1] b y 0.06 [1] white w x 0.28 [1] w y typ.-0.03 0.29 typ.+0.03 [1] viewing angle (contrast ratio>10) x axis, right( =0) r -- 89 -- degree [1], [6] x axis, left( =180) l -- 89 -- degree [1], [6] y axis, up( =90) u -- 89 -- degree [1], [6] y axis, down ( =270) d -- 89 -- degree [1], [6] www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 22/32 2008 all rights reserved no reproduction and redistribution allowed note [1]: the values of contrast ratio, surface lum inance, response time, color coordinates, and viewi ng angle are measured at center point of display area. note [2]: contrast ratio (cr) is defined mathematic ally as: note [3]: surface luminance is luminance value at c enter point of display area, 50cm from the surface with all pixels displaying white. note [4]: the variation in surface luminance, white(9p) is defined as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/minimum(l on1 , l on2 ,?l on9 ) note [5]: response time t r is the average time required for display transitio n by switching the input signal for five luminance ratio (0%, 25%, 50%, 75%, 100% brightness matrix) and is based on f v = 60hz to optimize. contrast ratio (cr) = brightness of 'full white' state brightness of 'full black' state 1 2 3 4 5 6 7 8 v h v/6 v/2 h/2 h/6 9 www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 23/32 2008 all rights reserved no reproduction and redistribution allowed note [6]: viewing angle is the angle at which the c ontrast ratio is greater than 10. the angles are de termined for the horizontal (or x-axis) and the vertical (or y-a xis) with respect to the z-axis which is normal to the lcd surface. 5. mechanical characteristics the contents provide general mechanical characteris tics for the model p645hw01 v0. detailed mechanical drawings are shown in the following pages. horizontal (typ.) 1482.4 mm vertical (typ.) 862.0 mm outline dimension depth (typ.) 58.9 mm (with inverter) horizontal (typ.) 814.6 mm bezel opening area vertical (typ.) 1440.6 mm horizontal 803.52 mm active display area vertical 1428.48 mm weight 30 kg (max) www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 24/32 2008 all rights reserved no reproduction and redistribution allowed 2d drawing (front) www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 25/32 2008 all rights reserved no reproduction and redistribution allowed 2d drawing (rear) www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 26/32 2008 all rights reserved no reproduction and redistribution allowed packing package information h tape 5cs modules 1pcs module/esd bag cushion top module 5 pcs / 1 carton cushion down c ushion set www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 27/32 2008 all rights reserved no reproduction and redistribution allowed pallet information by air cargo: (2 x 1) x 1 layers, one pallet put 2 boxes, total 10 pcs module. dimension: 1140 x 1660 x 1160mm by sea: (2 x 1) x 2 layers, one pallet put 2 boxes, stack 2 layers, total 20 pcs module. (40hq) dimension: 1140 x 1660 x 2320mm pallet dimension: 1140 x 1660 x 138mm www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 28/32 2008 all rights reserved no reproduction and redistribution allowed panel label carton label www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 29/32 2008 all rights reserved no reproduction and redistribution allowed 6. reliability test no test item q'ty condition 1 high temperature storage 3 pcs ta = 60c, 300hr j udge 2 low temperature storage 3 pcs ta = -20c, 300hr j udge 3 high temperature operation 3 pcs ta = 50c, 300hr judge 4 low temperature operation 3 pcs ta = -5c , 300hr judge 5 vibration test (non-operating) 3 pcs waveform: random vibration level: 1.5g rms bandwidth: 10-300hz duration: x, y, z 30min one time each direction 6 shock test (non-operating) 3 pcs shock level: 30g waveform: sine wave, 11ms direction: www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 30/32 2008 all rights reserved no reproduction and redistribution allowed 7. international standard 7.1 safety (1) ul60065,2003, underwriters laboratories, inc. ( auo file number : e204356) audio, video and similar electronic apparatus, safety requirement (2) ul60950-1,2003, underwriters laboratories, (auo file number : e204356) standard for safety of information technology e quipment including electrical business equipment (3) en60065 (4) en60950 (5) iec 60065, european committee for electro techn ical standardization (cenelec) audio, video and similar electronic apparatus, safe ty requirement (6) iec 60950-1: european committee for electrotechnical standardiza tion (cenelec) european standard for safety of information technol ogy equipment including electrical business equipment 7.2 emc (1) ansi c63.4 ?methods of measurement of radio-noi se emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 (2) c.i.s.p.r ?limits and methods of measurement of radio interface characteristics of information technology equipment.? international special commit tee on radio interference. (3) en 55022 ?limits and methods of measurement of radio interface characteristics of information technology equipment.? european committee for elect rotechnical standardization. (cenelec), 1998 www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 31/32 2008 all rights reserved no reproduction and redistribution allowed 8. precautions please pay attention to the followings when you use this tft lcd module. 8.1 mounting precautions (1) you must mount a module using holes arranged on back or edge side of panel. (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit br eak by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than hb pe ncil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosm etics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials l ike chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front/rear polarizer. do not use ace tone, toluene and alcohol because they cause chemic al damage to the polarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 8.2 operating precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage: v=200mv (over and under shoot voltage) (2) response time depends on the temperature. (in l ower temperature, it becomes longer.) (3) brightness of ccfl depends on the temperature. (in lower temperature, it becomes lower.) and in lo wer temperature, response time (required time that brig htness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperatu re change. condensation makes damage to polarizer o r electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference sha ll be done by system manufacturers. grounding and shieldi ng methods may be important to minimize the interface. www..net
model name: p645hw01 v0 product specification ?copyright au optronics corp. p645hw 01 v0 page 32/32 2008 all rights reserved no reproduction and redistribution allowed 8.3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through w rist band etc. and don?t touch interface pin direct ly. 8.4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 8.5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the temperature between 5c and 35c at normal humidity . (2) the polarizer surface should not come in contac t with any other object. it is recommended that the y be stored in the container in which they were shipped. 8.6 handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape. when the protection film i s peeled off, static electricity is generated between the fi lm and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded a nd with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of flue still on the bezel after the p rotection film is peeled off. (3) you can remove the glue easily. when the glue r emains on the bezel or its vestige is recognized, p lease wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexan e. 8.7 operating condition in pid application (1) if the continuous static display is required, p eriodically inserting a motion picture is strongly recommended. (2) recommend to periodically change the background color and background image. (3) recommend not to continuously operate over 18 h ours a day. (4) recommend to adopt one of the following actions after long time display. i. running the screen saver (motion picture or blac k pattern) ii. power off the system for a while (5) try not to run the lcd in a closed environment. suitable venting on the system cover would be help ful for cooling. (6) it is better to adapt active cooling with fans for long time displaying, especially for high luminance lcd model. www..net

▲Up To Search▲

Price & Availability of P645HW01V0

	To Download P645HW01V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .