upa801t npn silicon high frequency transistor ? small package style: 2 ne856 die in a 2 mm x 1.25 mm package ? low noise figure: nf = 1.2 db typ at 1 ghz ? high gain: |s 21e | 2 = 9.0 db typ at 1 ghz ? high collector current: 100ma features outline dimensions (units in mm) package outline s06 (top view) description nec's upa801t is two npn high frequency silicon epitaxial transistors encapsulated in an ultra small 6 pin smt package. each transistor is independently mounted and easily config- ured for either dual transistor or cascode operation. the high f t , low voltage bias and small size make this device ideally suited for pager and other hand-held wireless applications. notes: 1.pulsed measurement, pulse width 350 s, duty cycle 2 %. 2.the emitter terminal should be connected to the ground terminal of the 3 terminal capacitance bridge. for tape and reel version use part number upa801t-t1, 3k per reel. . note: pin 3 is identified with a circle on the bottom of the package. pin out 1. collector transistor 1 2. emitter transistor 1 3. collector transistor 2 4. emitter transistor 2 5. base transistor 2 6. base transistor 1 part number upa801t package outline s06 symbols parameters and conditions units min typ max i cbo collector cutoff current at v cb = 10 v, i e = 0 a 1.0 i ebo emitter cutoff current at v eb = 1 v, i c = 0 a 1.0 h fe 1 forward current gain at v ce = 3 v, i c = 7 ma 70 120 250 f t gain bandwidth at v ce = 3 v, i c = 7 ma ghz 3.0 4.5 cre 2 feedback capacitance at v cb = 3 v, i e = 0, f = 1 mhz pf 0.7 1.5 |s 21e | 2 insertion power gain at v ce = 3 v, i c = 7 ma, f = 1 ghz db 7 9 nf noise figure at v ce = 3 v, i c = 7 ma, f = 1 ghz db 1.2 2.5 h fe1 /h fe2 h fe ratio: h fe1 = smaller value of q 1 or q 2 0.85 h fe2 = larger value pf q 1 or q 2 electrical characteristics (t a = 25 c) california eastern laboratories 2.1 0.1 1.25 0.1 0 ~ 0.1 0.15 0.9 0.1 0.7 2.0 0.2 0.65 1.3 1 2 3 4 5 6 0.2 (all leads) +0.10 - 0.05
note: 1. operation in excess of any one of these parameters may result in permanent damage. symbols parameters units ratings v cbo collector to base voltage v 20 v ceo collector to emitter voltage v 12 v ebo emitter to base voltage v 3 i c collector current ma 100 p t total power dissipation 1 die mw 110 2 die mw 200 t j junction temperature c 150 t stg storage temperature c -65 to +150 absolute maximum ratings 1 (t a = 25 c) upa801t total power dissipation vs. ambient temperature collector current vs. base to emitter voltage total power dissipation, p t (mw) ambient temperature, t a ( c) base to emitter voltage, v be (v) collector current, i c (ma) collector current vs. collector to emitter voltage collector to emitter voltage, v ce (v) collector current, i c (ma) typical performance curves (t a = 25 c) 200 100 0 50 100 150 2 elements in total per element 20 0.5 1.0 10 0 v ce = 3 v 25 20 15 10 5 0510 l b =160 a 140 a 120 a 100 a 80 a 60 a 40 a 20 a dc current gain, h fe dc current gain vs. collector current collector current, i c (ma) 200 100 50 20 10 0.5 1 5 10 50 v ce = 3 v
upa801t typical performance curves (t a = 25 c) gain bandwidth product vs. collector current insertion power gain vs. collector current gain bandwidth product, f t (ghz) collector current, i c (ma) collector current, i c (ma) collector to base voltage, v cb (v) feed back capacitance, c re (pf) insertion power gain vs. frequency noise figure (db) noise figure vs. collector current feed back capacitance vs. collector to base voltage frequency, f (ghz) collector current, i c (ma) insertion power gain, is 21e i 2 (db) insertion power gain, is 21e i 2 (db) 20 10 5 2 1 0.5 1 5 10 50 v ce = 3 v f = 1 ghz 15 10 5 0 0.5 1 5 10 50 100 v ce = 3 v f = 1 ghz 6 4 2 0 0.5 1.0 5.0 10 50 100 v ce = 3 v f = 1 ghz 24 20 16 12 4 8 0 0.1 0.2 0.5 1.0 2.0 5.0 v ce = 3 v lc = 7 ma 5.0 2.0 1.0 0.5 0.2 0.1 12 51020 50 f = 1 mhz
upa801t typical scattering parameters (t a = 25 c) v ce = 3 v, i c = 3 ma, z 0 = 50 ? ? ? ? ? frequency s 11 s 21 s 12 s 22 (ghz) mag ang mag ang mag ang mag ang 0.10 .899 -30.5 5.578 153.7 .042 69.0 .923 -17.3 0.20 .808 -60.0 5.327 134.4 .069 54.5 .793 -29.2 0.30 .723 -86.7 4.877 119.6 .084 46.0 .679 -36.4 0.40 .660 -106.2 4.341 108.1 .093 41.1 .604 -39.5 0.50 .610 -125.9 3.883 98.5 .098 38.8 .550 -42.0 0.60 .583 -138.6 3.388 90.9 .102 37.4 .613 -44.2 0.70 .560 -150.0 3.046 84.3 .106 37.8 .487 -45.9 0.80 .547 -159.4 2.741 78.5 .108 38.1 .468 -47.9 0.90 .538 -167.4 2.498 73.4 .112 39.5 .455 -49.9 1.00 .535 -174.4 2.287 68.9 .116 41.0 .444 -52.3 1.10 .534 179.3 2.111 64.6 .120 43.0 .435 -54.7 1.20 .533 173.4 1.965 60.2 .125 45.1 .429 57.2 1.30 .533 168.3 1.830 56.3 .131 46.7 .424 -59.9 1.40 .534 163.2 1.721 52.7 .139 48.3 .422 -62.8 1.50 .538 158.7 1.620 49.2 .146 49.8 .417 -65.7 1.60 .542 154.3 1.544 45.7 .155 51.3 .414 -68.8 1.70 .545 150.0 1.464 42.7 .164 52.4 .415 -72.0 1.80 .548 146.1 1.396 39.5 .174 53.0 .412 -75.3 1.90 .552 142.0 1.336 36.6 .187 53.7 .411 -78.8 2.00 .556 138.3 1,280 33.6 .199 54.1 .411 -82.3 upa801t v ce = 3 v, i c = 1 ma, z 0 = 50 ? ? ? ? ? frequency s 11 s 21 s 12 s 22 (ghz) mag ang mag ang mag ang mag ang 0.10 .967 -22.9 1.935 159.9 .045 74.0 .978 -9.2 0.20 .930 -45.8 1.968 143.1 .083 60.1 .931 -17.4 0.30 .884 -67.1 1.938 129.1 .108 48.9 .870 -23.2 0.40 .842 -86.9 1.827 117.2 .125 39.4 .822 -28.0 0.50 .801 -103.1 1.748 106.7 .134 32.6 .779 -31.9 0.60 .771 -117.0 1.576 97.4 .137 27.1 .749 -35.3 0.70 .742 -130.0 1.498 89.2 .137 22.9 .722 -38.4 0.80 .722 -141.2 1.403 81.9 .134 20.0 .702 -41.3 0.90 .706 -151.1 1.326 75.6 .129 18.5 .690 -44.4 1.00 .696 -159.9 1.242 69.6 .124 17.8 .680 -47.4 1.10 .689 -167.7 1.169 64.5 .118 18.1 .671 -50.4 1.20 .685 -174.9 1.102 59.6 .112 19.8 .666 -53.6 1.30 .681 178.7 1.030 55.3 .106 23.5 .660 -56.9 1.40 .681 172.6 .979 50.9 .103 28.0 .658 -60.4 1.50 .683 166.8 .925 47.2 .100 33.6 .654 -64.0 1.60 .684 161.4 .884 43.6 .102 40.4 .651 -67.6 1.70 .684 156.1 .842 40.4 .107 47.5 .651 -71.5 1.80 .686 151.4 .804 37.3 .115 53.5 .649 -75.1 1.90 .689 146.6 .773 34.6 .127 57.9 .646 -79.2 2.00 .690 142.1 .738 32.3 .141 62.1 .646 -83.0
upa801t typical scattering parameters (t a = 25 c) frequency s 11 s 21 s 12 s 22 (ghz) mag ang mag ang mag ang mag ang v ce = 3 v, i c = 5 ma, z 0 = 50 ? ? ? ? ? 0.10 .819 -38.9 8.934 148.0 .038 65.8 .868 -23.6 0.20 .701 -73.4 8.007 127.6 .060 53.1 .687 -36.7 0.30 .608 -102.3 6.898 112.6 .072 47.6 .560 -42.4 0.40 .549 -123.6 5.819 101.8 .079 45.2 .483 -45.4 0.50 .511 -139.6 4.970 93.5 .086 45.7 .434 -47.2 0.60 .494 -151.0 4.255 86.9 .093 46.5 .402 -48.6 0.70 .481 -160.8 3.750 81.4 .099 47.2 .379 -49.9 0.80 .475 -168.6 3.328 76.3 .107 48.9 .361 -51.5 0.90 .472 -175.7 3.004 72.0 .113 49.7 .350 -53.4 1.00 .471 178.2 2.734 67.7 .122 50.9 .340 -55.4 1.10 .473 172.8 2.522 64.0 .130 51.6 .332 -57.3 1.20 .474 167.6 2.355 60.2 .139 52.3 .328 59.7 1.30 .474 162.9 2.176 56.7 .148 53.1 .322 -62.3 1.40 .477 158.4 2..038 53.2 .158 53.3 .319 -65.2 1.50 .481 154.4 1.921 49.8 .168 53.7 .315 -68.2 1.60 .484 150.3 1.818 46.7 .177 53.3 .313 -70.9 1.70 .489 146.5 1.726 43.9 .190 53.3 .312 -73.9 1.80 .490 142.9 1.647 40.6 .200 53.0 .312 -77.2 1.90 .495 139.3 1.578 37.6 .212 52.7 .309 -80.8 2.00 .501 136.0 1.505 35.0 .223 52.0 .309 -84.0 v ce = 3 v, i c = 7 ma, z 0 = 50 ? ? ? ? ? frequency s 11 s 21 s 12 s 22 (ghz) mag ang mag ang mag ang mag ang 0.10 .750 -45.7 11.858 144.0 .035 63.3 .816 -28.5 0.20 .618 -84.9 10.093 122.3 .053 53.2 .609 -41.8 0.30 .528 -114.5 8.219 107.7 .054 50.6 .481 -46.7 0.40 .483 -134.3 6.684 97.9 .073 50.6 .411 -49.1 0.50 .459 -148.5 5.565 90.5 .081 50.7 .365 -50.5 0.60 .447 -158.8 4.737 84.6 .089 52.3 .337 -51.5 0.70 .441 -167.4 4.134 79.7 .098 53.5 .337 -51.5 0.80 .439 -174.4 3.653 75.2 .107 54.2 .300 -54.2 0.90 .437 179.2 3.283 71.1 .117 54.9 .290 -55.9 1.00 .437 173.7 2.978 67.2 .126 55.6 .281 -57.9 1.10 .440 168.6 2.732 63.7 .136 55.8 .275 -59.8 1.20 .443 163.9 2.533 60.0 .147 55.3 .270 -52.3 1.30 .444 159.6 2.357 66.6 .158 55.4 .267 -64.7 1.40 .449 155.5 2.216 53.4 .169 55.3 .264 -67.5 1.50 .450 151.6 2.077 50.3 .180 54.7 .259 -70.5 1.60 .455 147.9 1.972 47.4 .192 64.5 .258 -73.3 1.70 .459 144.3 1.868 44.3 .202 53.9 .256 -76.3 1.80 .462 140.9 1.789 41.3 .214 53.0 .255 -79.6 1.90 .466 137.5 1.702 38.4 .226 52.3 .253 -83.0 2.00 .470 134.4 1.635 36.1 .238 51.5 .253 -86.4 part number quantity packaging UPA801T-T1-A 3000 tape & reel ordering information
upa801t units parameter units time seconds capacitance farads inductance henries resistance ohms voltage volts current amps model range frequency: 0.1 to 3.0 ghz bias: v ce = 1 v to 5 v, i c = 1 ma to 10 ma date: 12/98 note: this nonlinear model utilized the latest data available. see our design parameter library at www.cel.com for this data. nonlinear model (1) gummel-poon model parameters q1, q2 parameters q1, q2 is 6e-16 mjc 0.55 bf 120 xcjc 0.3 nf 0.98 cjs 0 vaf 10 vjs 0.75 ikf 0.08 mjs 0 ise 32e-16 fc 0.5 ne 1.93 tf 12e-12 br 12 xtf 6 nr 0.991 vtf 10 var 3.9 itf 0.2 ikr 0.17 ptf 0 isc 0 tr 1e-9 nc 2 eg 1.11 re 0.38 xtb 0 rb 4.16 xti 3 rbm 3.6 kf 1.56e-18 irb 1.96e-4 af 1.49 rc 2 cje 2.8e-12 vje 1.3 mje 0.5 cjc 1.1e-12 vjc 0.7 bjt nonlinear model parameters (1)
upa801t exclusive north american agent for rf, microwave & optoelectronic semiconductors california eastern laboratories ?headquarters ?4590 patrick henry drive ?santa clara, ca 95054-1817 ?(408) 988-3500 ?telex 34-6393 ?fax (408) 988-0279 24-hour fax-on-demand: 800-390-3232 (u.s. and canada only) ?internet: http://www.cel.com 9/99 data subject to change without notice nonlinear model schematic model range frequency: 0.1 to 3.0 ghz bias: v ce = 1 v to 5 v, i c = 1 ma to 10 ma date: 12/98 pin_1 pin_2 pin_3 pin_4 pin_5 pin_6 0.07 pf ccepkg2 ccbpkg2 0.6 nh 0.07 pf cce2 ccb2 0.07 pf cce1 0.1 pf 0.82 nh 0.6 nh 0.05 nh 0.65 nh q1 q2 ccbpkg1 ccb1 le1 lb1 lb 0.05 nh lb 0.05 nh le c_b2e2 0.05 pf c_b1b2 0.05 pf lb2 le2 c_c1b2 0.1 pf lc 0.05 nh lc 0.05 nh le 0.05 nh c_e1c2 c_c1e1 0.05 pf 0.05 pf c_e1b2 0.1 pf 0.1 pf 0.06 pf 0.1 pf life support applications these nec products are not intended for use in life support devices, appliances, or systems where the malfunction of these prod ucts can reasonably be expected to result in personal injury. the customers of cel using or selling these products for use in such applications do so at their own risk and agree to fully indemnify cel for all damages resulting from such improper use or sale.
4590 patrick henry drive santa clara, ca 95054-1817 telephone: (408) 919-2500 facsimile: ( 408 ) 988-0279 subject: compliance with eu directives cel certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of european union (eu) directive 2002/95/ec restriction on use of hazardous substances in electrical and electronic equipment (rohs) and the requirements of eu directive 2003/11/ec restriction on penta and octa bde. cel pb-free products have the same base part number with a suffix added. the suffix ? indicates that the device is pb-free. the ?z suffix is used to designate devices containing pb which are exempted from the requirement of rohs directive (*). in all cases the devices have pb-free terminals. all devices with these suffixes meet the requirements of the rohs directive. this status is based on cel? understanding of the eu directives and knowledge of the materials that go into its products as of the date of disclosure of this information. restricted substance per rohs concentration limit per rohs (values are not yet fixed) concentration contained in cel devices -a -az lead (pb) < 1000 ppm not detected (*) mercury < 1000 ppm not detected cadmium < 100 ppm not detected hexavalent chromium < 1000 ppm not detected pbb < 1000 ppm not detected pbde < 1000 ppm not detected if you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. important information and disclaimer: information provided by cel on its website or in other communications concerting the substan ce content of its products represents knowledge and belief as of the date that it is provided. cel bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. efforts are underway t o better integrate information from third parties. cel has taken and continues to take reasonable steps to provide representative and ac curate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. cel and ce l suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall cel? liability arising out of such information exceed the total purchase price of the cel part(s) at issue s old by cel to customer on an annual basis. see cel terms and conditions for additional clarification of warranties and liability.
|
