View AAT1149_1803590.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 1 switchreg ? general description the AAT1149 switchreg is a 3.0mhz step-down converter with an input voltage range of 2.7v to 5.5v and output voltage as low as 1.0v. it is opti- mized to react quickly to load variations and oper- ate with a tiny 0603 inductor that is only 1mm tall. the AAT1149 output voltage is programmable via external feedback resistors. it can deliver 400ma of load current while maintaining a low 45 a no load quiescent current. the 3.0mhz switching frequen- cy minimizes the size of external components while keeping switching losses low. the AAT1149 maintains high efficiency throughout the operating range, which is critical for portable applications. the AAT1149 is available in a pb-free, space-saving 2.0x2.1mm sc70jw-8 package and is rated over the -40c to +85c temperature range. features ? ultra-small 0603 inductor (height = 1mm) ?v in range: 2.7v to 5.5v ?v out adjustable from 1.0v to v in ? 400ma max output current ? up to 98% efficiency ?45 a no load quiescent current ? 3.0mhz switching frequency ?70 s soft start ? fast load transient ? over-temperature protection ? current limit protection ? 100% duty cycle low-dropout operation ?<1 a shutdown current ? sc70jw-8 package ? temperature range: -40c to +85c applications ? cellular phones ? digital cameras ? handheld instruments ? microprocessor / dsp core / io power ? pdas and handheld computers ? usb devices typical application l1 1.8h c1 4.7f r1 118k r2 59k v out = 1.8v v in = 3.6v c2 4.7f en fb in lx agnd pgnd pgnd pgnd AAT1149 u1
pin descriptions pin configuration sc70jw-8 (top view) pin # symbol function 1 en enable pin. 2 fb feedback input pin. this pin is connected to an external resistive divider for an adjustable output. 3 in input supply voltage for the converter. 4 lx switching node. connect the inductor to this pin. it is internally connected to the drain of both high- and low-side mosfets. 5 agnd non-power signal ground pin. 6, 7, 8 pgnd main power ground return pins. connect to the output and input capacitor return. AAT1149 3mhz fast transient 400ma step-down converter 2 1149.2006.11.1.0 fb in lx pgnd pgnd pgnd agnd en 1 2 3 45 6 7 8
absolute maximum ratings 1 thermal information symbol description value units p d maximum power dissipation 2, 3 625 mw ja thermal resistance 2 160 c/w symbol description value units v in input voltage to gnd 6.0 v v lx lx to gnd -0.3 to v in + 0.3 v v fb fb to gnd -0.3 to v in + 0.3 v v en en to gnd -0.3 to 6.0 v t j operating junction temperature range -40 to 150 c t lead maximum soldering temperature (at leads, 10 sec) 300 c AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 3 1. stresses above those listed in absolute maximum ratings may cause permanent damage to the device. functional operation at c ondi- tions other than the operating conditions specified is not implied. only one absolute maximum rating should be applied at any one time. 2. mounted on an fr4 board. 3. derate 6.25mw/c above 25c.
AAT1149 3mhz fast transient 400ma step-down converter 4 1149.2006.11.1.0 electrical characteristics 1 v in = 3.6v, t a = -40c to +85c, unless otherwise noted. typical values are t a = 25c. symbol description conditions min typ max units step-down converter v in input voltage 2.7 5.5 v v in rising 2.7 v v uvlo uvlo threshold hysteresis 100 mv v in falling 1.8 v v out output voltage tolerance i out = 0 to 400ma, -3.0 3.0 % v in = 2.7v to 5.5v v out adjustable output voltage range 1.0 v in v i q quiescent current no load 45 70 a i shdn shutdown current v en = gnd 1.0 a i lim p-channel current limit 600 ma r ds(on)h high side switch on resistance 0.45 r ds(on)l low side switch on resistance 0.40 i lxleak lx leakage current v in = 5.5v, v lx = 0 to v in , 1 a v en = gnd v linereg line regulation v in = 2.7v to 5.5v 0.1 %/v v out out threshold voltage accuracy 0.6v output, no load 591 600 609 mv t a = 25c i out out leakage current 0.6v output 0.2 a t s start-up time from enable to output 70 s regulation f osc oscillator frequency t a = 25c 3.0 mhz t sd over-temperature shutdown threshold 140 c t hys over-temperature shutdown hysteresis 15 c en v en(l) enable threshold low 0.6 v v en(h) enable threshold high 1.4 v i en input low current v in = v out = 5.5v -1.0 1.0 a 1. the AAT1149 is guaranteed to meet performance specifications over the -40c to +85c operating temperature range and is assu red by design, characterization, and correlation with statistical process controls.
typical characteristics AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 5 switching frequency vs. input voltage input voltage (v) frequency variation (%) -4 -3 -2 -1 0 1 2 2.5 3 3.5 4 4.5 5 5. 5 v out = 1.1v v out = 1.8v v out = 3v no load quiescent current vs. input voltage input voltage (v) supply current (a) 0 10 20 30 40 50 60 70 2.5 3 3.5 4 4.5 5 5.5 6 85 c -40 c 25 c load regulation (v out = 1.8v; l = 2.2h) load current (ma) output error (%) -1.00 -0.75 -0.50 -0.25 0.00 0.25 0.50 0.75 1.00 0.1 1 10 100 100 0 v in = 2.7v v in = 4.2v v in = 3v v in = 3.6v v in = 5v efficiency vs. load current (v out = 1.8v; l = 2.2h) load current (ma) efficiency (%) 50 60 70 80 90 100 0.1 1 10 100 100 0 v in = 4.2v v in = 2.7v v in = 3.6v v in = 5v v in = 3v load regulation (v out = 3v; l = 3h) load current (ma) output error (%) -1.00 -0.75 -0.50 -0.25 0.00 0.25 0.50 0.75 1.00 0.1 1 10 100 1000 v in = 4.2v v in = 5v v in = 3.3v efficiency vs. load current (v out = 3v; l = 3h) load current (ma) efficiency (%) 50 60 70 80 90 100 0.1 1 10 100 1000 v in = 3.3v v in = 4.2v v in = 5v
AAT1149 3mhz fast transient 400ma step-down converter 6 1149.2006.11.1.0 typical characteristics line transient (v out = 1.8; 400ma load; no feedforward capacitor) time (50s/div) input voltage (top) (v) output voltage (bottom) (v) 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 1.74 1.76 1.78 1.80 1.82 1.84 1.86 1.88 1.90 line regulation (v out = 1.1v) input voltage (v) accuracy (%) -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 2.5 3 3.5 4 4.5 5 5.5 6 1ma 0ma 600ma 400ma line regulation (v out = 1.8v) input voltage (v) accuracy (%) -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 2.5 3 3.5 4 4.5 5 5.5 6 400ma 600ma 0ma 100ma line regulation (v out = 3v) input voltage (v) accuracy (%) -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 2.5 3 3.5 4 4.5 5 5. 5 0ma 400ma 100ma 1ma 600ma 300ma output voltage error vs. temperature (v in = 3.6v; v o = 1.8v; i out = 400ma) temperature ( c) output error (%) -2.0 -1.0 0.0 1.0 2.0 -40 -20 0 20 40 60 80 100 switching frequency variation vs. temperature temperature ( c) variation (%) -10 -8 -6 -4 -2 0 2 4 6 8 10 -40 -20 0 20 40 60 80 100 120
typical characteristics AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 7 p-channel r ds(on) vs. input voltage input voltage (v) r ds(on) (m ) 300 350 400 450 500 550 600 650 700 750 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 25 c 120 c 100 c 85 c n-channel r ds(on) vs. input voltage input voltage (v) r ds(on) (m ) 300 350 400 450 500 550 600 650 700 750 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 25 c 120 c 100 c 85 c load transient (v out = 1.1v; c ff = 100pf) time (50s/div) load and inductor current (bottom) (a) output voltage (top) (v) 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 1ma 400ma load transient (v out = 1.1v; no feedforward capacitor) time (50s/div) load and inductor current (bottom) (a) output voltage (top) (v) 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 1ma 400ma line transient (v out = 1.8; c ff = 100pf) time (20s/div) input voltage (top) (v) output voltage (bottom) (v) 1.78 1.79 1.80 1.81 1.82 1.83 1.84 1.85 1.86 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 line transient (v out = 1.8; no load; no feedforward capacitor) time (50s/div) input voltage (top) (v) output voltage (bottom) (v) 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 1.78 1.80 1.82 1.84 1.86 1.88 1.90 1.92 1.94
typical characteristics AAT1149 3mhz fast transient 400ma step-down converter 8 1149.2006.11.1.0 soft start (v out = 1.8v; c ff = 100pf) time (50s/div) inductor current (bottom) (250ma/div) enable and output voltage (top) (v) -1.50 -1.00 -0.50 0.00 0.50 1.00 1.50 2.00 2.50 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 soft start (v out = 1.8v; no feedforward capacitor) time (50s/div) inductor current (bottom) (250ma/div) enable and output voltage (top) (v) -4.00 -3.00 -2.00 -1.00 0.00 1.00 2.00 3.00 4.00 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 load transient (v out = 1.8v; c ff = 100pf) time (50s/div) load and inductor current (bottom) (a) output voltage (top) (v) 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 400ma 1ma load transient (v out = 1.8v; no feedforward capacitor) time (50s/div) load and inductor current (bottom) (a) output voltage (top) (v) 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 400ma 1ma load transient (v out = 1.8v; c ff = 100pf) time (50s/div) load and inductor current (bottom) (a) output voltage (top) (v) 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 10ma 400ma load transient (v out = 1.8v; no feedforward capacitor) time (50s/div) load and inductor current (bottom) (a) output voltage (top) (v) 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 0.00 0.25 0.75 1.00 1.25 1.50 1.75 2.00 10ma 400ma
typical characteristics AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 9 soft start (v out = 1.1v; no feedforward capacitor) time (20s/div) inductor current (bottom) (250ma/div) enable and output voltage (top) (v) -0.50 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 -0.75 -0.50 -0.25 0.00 0.25 0.50 0.75 1.00 1.25 soft start (v out = 3v; no feedforward capacitor) time (50s/div) inductor current (bottom) (250ma/div) enable and output voltage (top) (v) -4.00 -3.00 -2.00 -1.00 0.00 1.00 2.00 3.00 4.00 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
AAT1149 3mhz fast transient 400ma step-down converter 10 1149.2006.11.1.0 functional block diagram functional description the AAT1149 is a high performance 400ma 3.0mhz monolithic step-down converter. it minimizes exter- nal component size, enabling the use of a tiny 0603 inductor that is only 1mm tall, and optimizes effi- ciency over the complete load range. apart from the small bypass input capacitor, only a small l-c filter is required at the output. typically, a 1.8 h inductor and a 4.7 f ceramic capacitor are recommended (see table of values). only three external power components (c in , c out , and l) are required. output voltage is programmed with external feedback resistors, ranging from 1.0v to the input voltage. an additional feed-forward capacitor can also be added to the external feed- back to provide improved transient response (see figure 4). at dropout, the converter duty cycle increases to 100% and the output voltage tracks the input volt- age minus the r ds(on) drop of the p-channel high- side mosfet. the input voltage range is 2.7v to 5.5v. the con- verter efficiency has been optimized for all load conditions, ranging from no load to 400ma. the internal error amplifier and compensation pro- vides excellent transient response, load, and line regulation. soft start eliminates any output voltage overshoot when the enable or the input voltage is applied. en lx err . amp logic dh dl pgnd in agnd voltage reference input fb
AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 11 control loop the AAT1149 is a peak current mode step-down converter. the current through the p-channel mosfet (high side) is sensed for current loop control, as well as short circuit and overload pro- tection. a fixed slope compensation signal is added to the sensed current to maintain stability for duty cycles greater than 50%. the peak current mode loop appears as a voltage-programmed current source in parallel with the output capacitor. the output of the voltage error amplifier programs the current mode loop for the necessary peak switch current to force a constant output voltage for all load and line conditions. internal loop compen- sation terminates the transconductance voltage error amplifier output. for the adjustable output, the error amplifier reference is fixed at 0.6v. soft start / enable soft start limits the current surge seen at the input and eliminates output voltage overshoot. when pulled low, the enable input forces the AAT1149 into a low-power, non-switching state. the total input current during shutdown is less than 1 a. current limit and over-temperature protection for overload conditions, the peak input current is limited. to minimize power dissipation and stresses under current limit and short-circuit conditions, switching is terminated after entering current limit for a series of pulses. switching is terminated for seven consecutive clock cycles after a current limit has been sensed for a series of four consecutive clock cycles. thermal protection completely disables switching when internal dissipation becomes excessive. the junction over-temperature threshold is 140c with 15c of hysteresis. once an over-temperature or over-current fault conditions is removed, the output voltage automatically recovers. under-voltage lockout internal bias of all circuits is controlled via the in input. under-voltage lockout (uvlo) guarantees sufficient v in bias and proper operation of all inter- nal circuitry prior to activation. applications information inductor selection the step-down converter uses peak current mode control with slope compensation to maintain stability for duty cycles greater than 50%. the output induc- tor value must be selected so the inductor current down slope meets the internal slope compensation requirements. table 1 displays suggested inductor values for various output voltages. manufacturer's specifications list both the inductor dc current rating, which is a thermal limitation, and the peak current rating, which is determined by the saturation characteristics. the inductor should not show any appreciable saturation under normal load conditions. some inductors may meet the peak and average current ratings yet result in excessive loss- es due to a high dcr. always consider the losses associated with the dcr and its effect on the total converter efficiency when selecting an inductor. the 1.8 h cdrh2d09 series inductor selected from sumida has a 131m dcr and a 400ma sat- uration current rating. at full load, the inductor dc loss is 21mw which gives a 2.8% loss in efficiency for a 400ma, 1.8v output. input capacitor select a 4.7 f to 10 f x7r or x5r ceramic capac- itor for the input. to estimate the required input capacitor size, determine the acceptable input rip- ple level (v pp ) and solve for c. the calculated value varies with input voltage and is a maximum when v in is double the output voltage. c in(min) = 1 ?? - esr 4 f s ?? v pp i o ?? 1 - = for v in = 2 v o ?? v o v in v o v in 1 4 ?? 1 - ?? v o v in c in = v o v in ?? - esr f s ?? v pp i o
AAT1149 3mhz fast transient 400ma step-down converter 12 1149.2006.11.1.0 table 1: inductor values. configuration output voltage typical inductor value 1v, 1.2v 1.0 h to 1.2 h 0.6v adjustable with 1.5v, 1.8v 1.5 h to 1.8 h external feedback 2.5v 2.2 h to 2.7 h 3.3v 3.3 h always examine the ceramic capacitor dc voltage coefficient characteristics when selecting the prop- er value. for example, the capacitance of a 10 f, 6.3v, x5r ceramic capacitor with 5.0v dc applied is actually about 6 f. the maximum input capacitor rms current is: the input capacitor rms ripple current varies with the input and output voltage and will always be less than or equal to half of the total dc load current. for v in = 2 v o the term appears in both the input voltage ripple and input capacitor rms current equations and is a maximum when v o is twice v in . this is why the input voltage ripple and the input capacitor rms current ripple are a maximum at 50% duty cycle. the input capacitor provides a low impedance loop for the edges of pulsed current drawn by the AAT1149. low esr/esl x7r and x5r ceramic capacitors are ideal for this function. to minimize stray inductance, the capacitor should be placed as closely as possible to the ic. this keeps the high frequency content of the input current local- ized, minimizing emi and input voltage ripple. the proper placement of the input capacitor (c2) can be seen in the evaluation board layout in figure 1. a laboratory test set-up typically consists of two long wires running from the bench power supply to the evaluation board input voltage pins. the induc- tance of these wires, along with the low-esr ceramic input capacitor, can create a high q net- work that may affect converter performance. this problem often becomes apparent in the form of excessive ringing in the output voltage during load transients. errors in the loop phase and gain meas- urements can also result. since the inductance of a short pcb trace feeding the input voltage is significantly lower than the power leads from the bench power supply, most applications do not exhibit this problem. in applications where the input power source lead inductance cannot be reduced to a level that does not affect the converter performance, a high esr tantalum or aluminum electrolytic should be placed in parallel with the low esr, esl bypass ceramic. this dampens the high q network and stabilizes the system. output capacitor the output capacitor limits the output ripple and provides holdup during large load transitions. a 4.7 f to 10 f x5r or x7r ceramic capacitor typi- cally provides sufficient bulk capacitance to stabi- lize the output during large load transitions and has the esr and esl characteristics necessary for low output ripple. the output voltage droop due to a load transient is dominated by the capacitance of the ceramic out- ?? 1 - ?? v o v in v o v in i o rms(max) i 2 = ?? 1 - = d (1 - d) = 0.5 2 = ?? v o v in v o v in 1 2 ?? i rms = i o 1 - ?? v o v in v o v in
AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 13 put capacitor. during a step increase in load cur- rent, the ceramic output capacitor alone supplies the load current until the loop responds. within two or three switching cycles, the loop responds and the inductor current increases to match the load current demand. the relationship of the output volt- age droop during the three switching cycles to the output capacitance can be estimated by: once the average inductor current increases to the dc load level, the output voltage recovers. the above equation establishes a limit on the minimum value for the output capacitor with respect to load transients. the internal voltage loop compensation also limits the minimum output capacitor value to 4.7 f. this is due to its effect on the loop crossover frequency (bandwidth), phase margin, and gain margin. increased output capacitance will reduce the crossover frequency with greater phase margin. the maximum output capacitor rms ripple current is given by: figure 1: AAT1149 evaluation board figure 2: exploded view of evaluation top side. board top side. figure 3: AAT1149 evaluation board bottom side. 1 23 v out (v in(max) - v out ) rms(max) i l f s v in(max) = c out = 3 i load v droop f s
AAT1149 3mhz fast transient 400ma step-down converter 14 1149.2006.11.1.0 dissipation due to the rms current in the ceramic output capacitor esr is typically minimal, resulting in less than a few degrees rise in hot-spot temperature. feedback resistor selection resistors r1 and r2 of figure 4 program the output to regulate at a voltage higher than 0.6v. to limit the bias current required for the external feedback resis- tor string while maintaining good noise immunity, the minimum suggested value for r2 is 59k . although a larger value will further reduce quiescent current, it will also increase the impedance of the feedback node, making it more sensitive to external noise and interference. table 2 summarizes the resistor values for various output voltages with r2 set to either 59k for good noise immunity or 221k for reduced no load input current. the AAT1149, combined with an external feedfor- ward capacitor (c3 in figure 4), delivers enhanced transient response for extreme pulsed load appli- cations. the addition of the feedforward capacitor typically requires a larger output capacitor c1 for stability. table 2: feedback resistor values. r2 = 59k r2 = 221k v out (v) r1 (k )r1 0.9 29.4 113k 1.0 39.2 150k 1.1 49.9 187k 1.2 59.0 221k 1.3 68.1 261k 1.4 78.7 301k 1.5 88.7 332k 1.8 118 442k 1.85 124 464k 2.0 137 523k 2.5 187 715k 3.3 267 1.00m figure 4: AAT1149 evaluation board schematic. ?? ?? r1 = -1 r2 = - 1 59k = 88.5k v out v ref ?? ?? 1.5v 0.6v l1 4.7 f c1 4.7 f c2 v out v in gnd gnd 1 2 3 enable lx en 1 out 2 in 3 lx 4 agnd 5 pgnd 6 pgnd 7 pgnd 8 AAT1149 u1 r1 59k r2 c3
AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 15 thermal calculations there are three types of losses associated with the AAT1149 step-down converter: switching losses, conduction losses, and quiescent current losses. conduction losses are associated with the r ds(on) characteristics of the power output switching devices. switching losses are dominated by the gate charge of the power output switching devices. at full load, assuming continuous conduction mode (ccm), a simplified form of the losses is given by: i q is the step-down converter quiescent current. the term t sw is used to estimate the full load step- down converter switching losses. for the condition where the step-down converter is in dropout at 100% duty cycle, the total device dis- sipation reduces to: since r ds(on) , quiescent current, and switching losses all vary with input voltage, the total losses should be investigated over the complete input voltage range. given the total losses, the maximum junction tem- perature can be derived from the ja for the sc70jw-8 package which is 160c/w. layout the suggested pcb layout for the AAT1149 is shown in figures 1, 2, and 3. the following guide- lines should be used to help ensure a proper layout. 1. the input capacitor (c2) should connect as close- ly as possible to in (pin 3) and pgnd (pins 6-8). 2. c1 and l1 should be connected as closely as possible. the connection of l1 to the lx pin should be as short as possible. 3. the feedback trace or fb pin (pin 2) should be separate from any power trace and connect as closely as possible to the load point. sensing along a high-current load trace will degrade dc load regulation. if external feedback resistors are used, they should be placed as closely as possible to the fb pin (pin 2) to minimize the length of the high impedance feedback trace. 4. the resistance of the trace from the load return to the pgnd (pins 6-8) should be kept to a minimum. this will help to minimize any error in dc regulation due to differences in the poten- tial of the internal signal ground and the power ground. a high density, small footprint layout can be achieved using an inexpensive, miniature, non- shielded, high dcr inductor, as shown in figure 5. figure 5: minimum footprint evaluation board using 2.0x1.25x1.0mm inductor. t j(max) = p total ja + t amb p total = i o 2 r ds(on)h + i q v in p total i o 2 (r ds(on)h v o + r ds(on)l [v in - v o ]) v in = + (t sw f s i o + i q ) v in
AAT1149 3mhz fast transient 400ma step-down converter 16 1149.2006.11.1.0 step-down converter design example specifications v o = 1.8v @ 400ma (adjustable using 0.6v version), pulsed load i load = 300ma v in = 2.7v to 4.2v (3.6v nominal) f s = 3.0mhz t amb = 85c 1.8v output inductor (use 2.2 h; see table 1) for taiyo yuden inductor cbc2518t2r2m, 2.2 h, dcr = 130m . 1.8v output capacitor v droop = 0.1v 1 23 1 1.8v (4.2v - 1.8v) 2.2 h 3.0mhz 4.2v 23 rms i l1 f s v in(max) = 3 i load v droop f s 3 0.3a 0.1v 3.0mhz c out = = = 3.0 f; use 4.7f = 45marms (v o ) (v in(max) - v o ) = p esr = esr i rms 2 = 5m (45ma) 2 = 10 w v o v o 1.8 v 1.8v i l1 = ? 1 - = ? 1 - = 156ma l1 ? f s v in 2.2 h ? 3.0mhz 4.2v i pkl1 = i o + i l1 = 0.4a + 0.078a = 0.478a 2 p l1 = i o 2 ? dcr = 0.4a 2 ? 130m = 21mw ? ? ? ? ? ? ? ? l1 = 1 ? v o = 1 ? 1.8v = 1.8 h sec a sec a
AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 17 input capacitor input ripple v pp = 25mv AAT1149 losses t j(max) = t amb + ja p loss = 85 c + (160 c/w) 140mw = 107 c p total + (t sw f s i o + i q ) v in i o 2 (r ds(on)h v o + r ds(on)l [v in -v o ] ) v in = = + (5ns 3mhz 0.4a + 70 a) 4.2v = 140m w 0.4 2 (0.725 1.8v + 0.7 [4.2v - 1.8v]) 4.2v i o rms i p = esr i rms 2 = 5m (0.2a) 2 = 0.2mw 2 = = 0.2arms c in = = = 1.45 f; use 2.2 f 1 ?? - esr 4 f s ?? v pp i o 1 ?? - 5m 4 3.0mhz ?? 25mv 0.4a
AAT1149 3mhz fast transient 400ma step-down converter 18 1149.2006.11.1.0 table 3: evaluation board component values. table 4: typical surface mount inductors. part number/ inductance rated dcr size (mm) manufacturer type ( h) current (ma) ( ) lxwxh 0.77 660 110 0603 brc1608 1.0 520 180 (h max = 1mm) 1.5 410 300 taiyo yuden 1.5 600 200 0805 brl2012 2.2 550 250 (h max = 1mm) 3.3 450 350 cbc2518 1.0 1000 80 2.5x1.8x1.8 wire wound chip 2.2 890 130 1.2 590 97.5 1.5 520 110 sumida cdrh2d09 1.8 480 131 3.2x3.2x1.0 shielded 2.5 440 150 3.0 400 195 1.0 485 300 murata lqh2mcn4r7m02 1.5 445 400 2.0x1.6x0.95 unshielded 2.2 425 480 3.3 375 600 0.68 980 31 0.82 830 54 coiltronics sd3118 1.2 720 75 3.15x3.15x1.2 shielded 1.5 630 104 2.2 510 116 3.3 430 139 adjustable version r2 = 59k r2 = 221k 1 (0.6v device) v out (v) r1 (k ) r1 (k ) l1 ( h) 1.0 39.2 150 1.0 1.2 59.0 221 1.2 1.5 88.7 332 1.5 1.8 118 442 1.8 2.5 187 715 2.2 3.3 267 1000 3.3 1. for reduced quiescent current, r2 = 221k .
table 5: surface mount capacitors. manufacturer part number value voltage temp. co. case murata grm219r61a475ke19 4.7 f 10v x5r 0805 murata grm21br60j106ke19 10 f 6.3v x5r 0805 murata grm185r60j475m 4.7 f 6.3v x58 0603 AAT1149 3mhz fast transient 400ma step-down converter 1149.2006.11.1.0 19
AAT1149 3mhz fast transient 400ma step-down converter 20 1149.2006.11.1.0 advanced analogic technologies, inc. 830 e. arques avenue, sunnyvale, ca 94085 phone (408) 737-4600 fax (408) 737-4611 1. contact sales for other voltage options. 2. xyy = assembly and date code. 3. sample stock is generally held on part numbers listed in bold . ordering information package information sc70jw-8 all dimensions in millimeters. output voltage 1 package marking 2 part number (tape and reel) 3 0.6; adj 1.0 sc70jw-8 rgxyy AAT1149ijs-0.6-t1 ? advanced analogic technologies, inc. analogictech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an analogictech pr oduct. no circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. analogictech reserves the right to make changes to their products or specifi cations or to discontinue any product or service without notice. customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information b eing relied on is current and complete. all products are sold sub- ject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. analogictech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with anal ogictech?s standard warranty. testing and other quality con- trol techniques are utilized to the extent analogictech deems necessary to support this warranty. specific testing of all param eters of each device is not necessarily performed. analogictech and the analogictech logo are trademarks of advanced analogic technologies incorporated. all other brand and produ ct names appearing in this document are regis- tered trademarks or trademarks of their respective holders. 0.225 0.075 0.45 0.10 0.05 0.05 2.10 0.30 2.00 0.20 7 3 4 4 1.75 0.10 0.85 0.15 0.15 0.05 1.10 max 0.100 2.20 0.20 0.048ref 0.50 bsc 0.50 bsc 0.50 bsc all analogictech products are offered in pb-free packaging. the term ?pb-free? means semiconductor products that are in compliance with current rohs standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. for more information, please visit our website at http://www.analogictech.com/pbfree.

▲Up To Search▲

Price & Availability of AAT1149

	To Download AAT1149 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .