62 nte electronics, inc. voice (973) 748 ? 5089 fax (973) 748 ? 6224 http://www.nteinc.com features ? replaces slow blow glass cartridge fuse ? .250? (6.35mm) quick connect terminals ? snap ? in mounting ? visual trip indicator ? push button to reset breaker nte type no. current rating amps typical resistance ohms r59 ? 0.25a 0.25 14.0 r59 ? 0.5a 0.50 3.55 r59 ? 1a 1.0 0.89 r59 ? 2a 2.0 0.17 r59 ? 3a 3.0 0.069 r59 ? 4a 4.0 0.043 r59 ? 5a 5.0 0.030 r59 ? 6a 6.0 0.026 r59 ? 7a 7.0 0.017 r59 ? 8a 8.0 0.016 r59 ? 10a 10.0 0.011 r59 ? 12a 12.0 0.009 r59 ? 15a 15.0 0.007 r59 ? 20a 20.0 0.007 trip times 0.25 to 2 amp types 3.0 to 20 amp types rated load trip times rated load trip times 100% no trip 100% no trip 175% trip in 1 hour 135% trip in 1 hour 200% 4.5 to 28.0 sec. 200% 2.2 to 15.0 sec. 400% 1.0 to 6.5 sec. 400% 0.55 to 1.8 sec. 600% 0.4 to 4.0 sec. 600% 0.27 to 0.7 sec. 800% 0.17 to 0.45 sec. 1000% 0.12 to 0.3 sec. r59 series thermal circuit breaker, fuse holder type d41 1.535 (38.99) max .325 (8.26) max .760 (19.31) max .760 (19.31) max .540 (13.72) max .625 (15.88) max .370 (9.4) .190 (4.83) .625 ? .635 (15.88 ? 16.13) .625 ? .635 (15.88 ? 16.13) .625 ? .635 (15.88 ? 16.13) .570 ? .575 (14.48 ? 14.61) .540 ? .550 (13.77 ? 13.97) recommended panel cutouts recommended panel thickness: .032 ? .062 (.813 ? 1.574) electrical specifications electrical characteristics (@ 25 c) calibration: will continuously carry 100% of rating. 0.25 to 2 amp types: may trip between 101% and 174%, but must trip at 175% of rating within one hour at +25 c 3.0 to 20 amp types: may trip between 101% and 134%, but must trip at 135% of rating within one hour at +25 c maximum operating voltages: 32 vdc; 250 vac, @ 50/60 hz dielectric strength: 1500vac rms resettable overload capacity: 0.25 to 2 amp types: six times rated current 3.0 to 20 amp types: ten times rated current reset time: 0.25 to 2 amp types: 180 seconds max. 3.0 to 20 amp types: 10 to 60 seconds typ. interrupt capacity: 1000 amps @ 250 vac, 50/60 hz. and 32 vdc in accordance with ul standard 1077 mechanical characteristics termination: .250 (6.35) quick connect terminals note: soldering to terminals is not recommended. mounting: snaps into panel from front (see recommended panel cutouts) weight: 0.35 ozs. (10 g) approx.
|
