PC956L0NSZ PC956L0NSZ absolute maximum ratings outline dimensions (unit : mm) parameter symbol rating unit forward current i f 25 ma ma reverse voltage input output v r 5v v power dissipation p45 output current supply voltage output voltage power dissipation 100 15 mw mw v o p o i o v v cc v iso (rms) kv operating temperature t opr ? 55 to + 125 ? 40 to + 100 ? 0.5 to + 35 ? 0.5 to + 35 c c storage temperature isolation voltage t stg *4 *3 *2 *1 *5 soldering temperature t sol 270 5.0 c (t a = 25 c) *1 when ambient temperature goes above 70 c, the power dissipation goes down at 0.45ma/ c *2 when ambient temperature goes above 70 c, the power dissipation goes down at 0.8mw/ c *3 when ambient temperature goes above 70 c, the power dissipation goes down at 1.8mw/ c *4 40 to 60%rh, ac for 1minute *5 for 10s 1. programmable controller 2. inverter features applications high speed and high cmr ? opic photocoupler 1. high resistance to noise (cmr:min. 15kv/ s) 2. high speed response (t phl :max. 400ns, t plh :max. 550ns) 3. standard dip type 4. isolation voltage (v iso (rms) = 5.0kv) 5. recognized by ul, file no. e64380 primary side mark : 0 to 13 ? 2.54 0.25 6.5 0.5 0.85 0.2 1.2 0.3 9.66 0.5 3.5 0.5 7.62 0.3 3.05 0.5 3.4 0.5 0.5 0.1 0.5 typ. 0.26 0.1 8 7 pc956l 6 5 1 8 7 6 5 1 2 3 4 2 3 4 1 2 3 4 5 6 7 8 ? ?pic?optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and signal- processing circuit integrated onto a single chip. internal connection diagram amp. nc anode cathode nc v l gnd v o v cc voltage regulator ? vde (vde0884) approved type is also available as an option notice in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occ ur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before usin g any sharp device. internet internet address for electronic components group http://sharp-world.com/ecg/
PC956L0NSZ parameter symbol unit input v a supply voltage low level output current high level supply current t a = 25 ? c, v r = 0, f = 1mhz pf output v ol v cc i ol high level output current i oh i cch low level supply current i ccl ma ma transfer characteristics "high low" threshold input current isolation resistance floating capacitance internal pull-up resistance i fhl r iso c f r l ma ? pf k ? t plh ns t phl ns propagation delay difference between any two parts ? tw ns distortion of pulse width t psk ns instantaneous common mode rejection voltage "output : high level" t a = 25 ? c, i f = 0, v cc = 15v, c l = 100pf, v cm = 1.5kv (p-p) , r l = 20k ? , v o > 3.0v, short circuit between pin and t a = 25 ? c, i f = 10ma, v cc = 15v, c l = 100pf, v cm = 1.5kv (p-p) , r l = 20k ? , v o < 1.0v, short circuit between pin and pin instantaneous common mode rejection voltage "output : low level" cm l kv/ s t a = 25 ? c, i f = 10ma t a = 25 ? c, v r = 5v min. ? ? ? 5 10 10 ? 14 30 270 ? ? 150 ? ? ? ? 15 max. 10 250 1.3 1.3 5 ? 1 25 450 450 ? 1.95 400 550 conditions "low high" propagation time "high low" propagation time *8 *8 *7 *9 *9 response time cmr cm h ? i f = 10ma, v o = 0.6v i f = 0, v cc = v o i f = 10ma, i o = 2.4ma i f = 0, v o = open i f = 10ma, v o = open v o = 0.8v, r l = 20k ? , v cc = 15v short circuit between pin and pin t a = 25 ? c, dc500v, 40 to 60%rh t a = 25 ? c, v = 0, f = 1mhz t a = 25 ? c i f = 10ma (t phl ), i f = 0 (t plh ), v cc = 15v, r l = 20k ? , c l = 100pf v thlh = 2.0v, v thhl = 1.5v short circuit between pin and typ. ? v 4.5 35 ? 60 v ? 0.6 0.3 0.6 ma 4.4 ? 9 a ? 50 5 0.8 1.5 10 11 0.6 20 190 200 1.6 210 400 kv/ s 15 ? 30 ? 30 (unless otherwise specified t a =? 40 to + 100 ? c, v cc = 4.5 to 35v) low level output voltage forward voltage reverse current terminal capacitance v f i r c t *6 it shall connect a by-pass capacitor of 0.01 f or more between v cc (pin 8 ) and gnd (pin 5 ) near the device, when it measures the transfer characteristics and the output side characteristics *7 distortion of pulse width ? tw = | t phl ? t plh | *8 refer to fig.1 *9 refer to fig.2 7 7 8 7 8 7 8 8 pin pin electro-optical characteristics *6 recommended operating conditions parameter symbol min. max. unit forward current output voltage operating temperature ma v supply voltage i f v o v cc t opr c 10 4.5 ? 40 0 20 35 100 35 v
PC956L0NSZ 0 120 p 0 25 50 70 100 125 100 80 60 20 40 45 power dissipation p, p o (mw) p o ? 40 ambient temperature t a ( ? c) fig.3 forward current vs. ambient temperature fig.4 power dissipation vs. ambient temperature 5 10 25 20 15 0 125 100 70 50 25 0 ? 40 ambient temperature t a ( ? c) forward current i f (ma) fig.2 test circuit for cm h and cm l 1.5kv 0v v cm cm h ,v o cm l ,v o (i f = 0ma) (i f = 10ma) sw is a sw is b v cc v o (min.) v o (max.) v ol v cm +? a b r l gnd c l 0.1 f i f v o v cc amp. voltage regulator t phl t plh t f 90% 10% i f r l gnd c l 0.1 f v ol v thlh v thhl 10ma 0ma i f v o v o v cc 47 ? amp. voltage regulator t r fig.1 test circuit for t phl and t plh
PC956L0NSZ output current i o (ma) 0 15 10 5 05 15 10 20 forward current i f (ma) v o = 0.6v t a =? 40 ? c t a = 25 ? c t a = 100 ? c fig.5 output current vs. forward current forward voltage v f (v) forward current i f (ma) 1 10 100 0.1 1.00 1.20 1.40 1.60 1.80 2.00 t a = 75 ? c t a = 50 ? c t a = 25 ? c t a = 0 ? c t a = 100 ? c t a =? 20 ? c t a =? 40 ? c fig.6 forward current vs. forward voltage relative output current i o (%) 60 120 70 100 110 80 90 ? 40 0 ? 20 60 80 40 20 100 ambient temperature t a ( ? c) i f = 10ma v o = 0.6v i o = 100% at t a = 25 ? c threshold input current i fhl (ma) 0.0 5.0 2.0 3.0 4.0 ? 40 0 ? 20 60 80 40 20 100 ambient temperature t a ( ? c) v cc = 15v v o = 0.8v r l = 20k ? 1.0 fig.7 relative output current vs. ambient temperature fig.8 threshold input current vs. ambient temperature supply current i cch , i ccl (ma) 0.0 1.6 0.6 0.4 0.2 1.2 1.4 0.8 1.0 ? 40 0 ? 20 60 80 40 20 100 ambient temperature t a ( ? c) v cc = 35v v o = open i cch :i f = 0ma i ccl :i f = 10ma i ccl i cch fig.10 supply current vs. ambient temperature low level output voltage v ol (v) 0.0 0.6 0.3 0.4 0.5 ? 40 0 ? 20 60 80 40 20 100 ambient temperature t a ( ? c) v cc = 4.5v i f = 10ma i o = 2.4ma 0.2 0.1 fig.9 low level output voltage vs. ambient temperature
PC956L0NSZ propagation delay time t phl , t plh ( s) 0 2.0 0.2 0.4 1.8 0.6 0.8 1.0 1.2 1.4 1.6 ? 40 0 ? 20 60 80 40 20 100 ambient temperature t a ( ? c) i f = 10ma v cc = 15v c l = 100pf r l = 20k ? t plh t phl fig.11 propagation delay time vs. ambient temperature propagation delay time t phl , t plh ( s) 0 2.0 0.2 0.4 1.8 0.6 0.8 1.0 1.2 1.4 1.6 load resistance r l (k ? ) i f = 10ma v cc = 15v c l = 100pf t plh t phl 0 5 10 15 20 25 30 35 40 45 50 fig.12 propagation delay time vs. load resistance propagation delay time t phl , t plh ( s) 0 2.0 0.2 0.4 1.8 0.6 0.8 1.0 1.2 1.4 1.6 0 100 50 300 350 400 450 250 200 150 500 load capacitance c l (pf) i f = 10ma v cc = 15v r l = 20k ? t plh t phl propagation delay time t phl , t plh ( s) 0 2.0 0.2 0.4 1.8 0.6 0.8 1.0 1.2 1.4 1.6 010 52530 20 15 35 supply voltage v cc (v) i f = 10ma c l = 100pf r l = 20k ? t plh t phl fig.13 propagation delay time vs. load capacitance fig.14 propagation delay time vs. supply voltage propagation delay time t phl , t plh ( s) 0 2.0 0.2 0.4 1.8 0.6 0.8 1.0 1.2 1.4 1.6 04 2101618 14 12 8 620 forward current i f (ma) t plh t phl v cc = 15v c l = 100pf r l = 20k ? fig.15 propagation delay time vs. forward current
notice the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: - - - personal computers - - - office automation equipment - - - telecommunication equipment [terminal] - - - test and measurement equipment - - - industrial control - - - audio visual equipment - - - consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: - - - transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - traffic signals - - - gas leakage sensor breakers - - - alarm equipment - - - various safety devices, etc. (iii)sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - space applications - - - telecommunication equipment [trunk lines] - - - nuclear power control equipment - - - medical and other life support equipment (e.g., scuba). if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp devices. this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. contact and consult with a sharp representative if there are any questions about the contents of this publication.
|
