Part Number Hot Search : 
PDTB1 C3510 SBR8210R BA8206F CS3390 ISP1212A 1N5461A 475M0
Product Description
Full Text Search
 

To Download ADM690A Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 a
Microprocessor Supervisory Circuits ADM690A/ADM692A/ADM802L/M/ADM805L/M
FUNCTIONAL BLOCK DIAGRAM
VBATT BATTERY SWITCHOVER VCC VOUT
FEATURES Precision Supply Voltage Monitor 4.65 V ADM690A/ADM802L/ADM805L 4.40 V ADM692A/ADM802M/ADM805M Reset Assertion Down to 1 V V CC Reset Timeout--200 ms Watchdog Timer--1.6 s 100 A Quiescent Supply Current Automatic Battery Backup Power Switching Voltage Monitor for Power Fail 2% Power Fail Accuracy on ADM802L/M Space-Saving MicroSOIC Package (ADM690A) APPLICATIONS Microprocessor Systems Computers Controllers Intelligent Instruments
4.65V*
RESET GENERATOR
RESET (RESET)
WATCHDOG INPUT (WDI)
WATCHDOG TRANSITION DETECTOR (1.6s)
POWER FAIL INPUT (PFI) 1.25V
ADM690A ADM692A ADM802L ADM802M ADM805L ADM805M
POWER FAIL OUTPUT (PFO)
*4.4V FOR ADM692A/ADM802M/ADM805M ( ) = ADM805L/M ONLY
GENERAL DESCRIPTION
The ADM690A/ADM692A/ADM802L/M/ADM805L/M family of supervisory circuits offers complete single chip solutions for power supply monitoring and battery control functions in microprocessor systems. These functions include P reset, backup battery switchover, watchdog timer, and power failure warning. The ADM690A/ADM692A/ADM802L/M/ADM805L/M are available in 8-pin packages and provide: 1. Power-on reset output during power-up, power-down and brownout conditions. The RESET output remains operational with VCC as low as 1 V. 2. Battery backup switching for CMOS RAM, CMOS microprocessor or other low power devices. 3. A reset pulse if the optional watchdog timer has not been toggled within 1.6 seconds. 4. A 1.25 V threshold detector for power fail warning, low battery detection, or to monitor a power supply other than +5 V. On the ADM690A/ADM802L/ADM805L the reset voltage threshold is 4.65 V. On the ADM692A/ADM802M/ ADM805M, the reset voltage threshold is 4.40 V. The ADM802L/ADM802M guarantee power fail accuracies to 2%.
The ADM805L/M provides an active high reset output, RESET instead of RESET. The family of products is fabricated using an advanced epitaxial CMOS process combining low power consumption and high reliability. RESET assertion is guaranteed with VCC as low as 1 V. They provide a pin-compatible upgrade for the MAX690A/ MAX692A/MAX802L/MAX802M/MAX805L All parts are available in 8-pin DIP and SOIC packages. The ADM690A is also available in a new space-saving microSOIC package.
REV. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 617/329-4700 World Wide Web Site: http://www.analog.com Fax: 617/326-8703 (c) Analog Devices, Inc., 1996
ADM690A/ADM692A/ADM802L/M/ADM805L/M-SPECIFICATIONS
(VCC = 4.75 V to 5.5 V (ADM690A/ADM802L/ADM805L), VCC = 4.5 V to 5.5 V, (ADM692A/ADM802M/ADM805M), VBATT = +2.8 V, TA = TMIN to TMAX unless otherwise noted)
Parameter
1
Min
Typ
Max 5.5 100 1.0 +0.02
Units V A A A V V V V mV mV mV
Test Conditions/Comments
VCC/VBATT OPERATION VCC Operating Voltage Range 1.0 Supply Current (Excludes IOUT) Supply Current in Battery Backup Mode Battery Standby Current (+ = Discharge, - = Charge) -0.1 VOUT Output Voltage VCC - 0.02 VCC - 0.5 VOUT in Battery Backup Mode Battery Switchover Threshold Battery Switchover Hysteresis RESET THRESHOLD Reset Voltage Threshold ADM690A, ADM802L, ADM805L ADM692A, ADM802M, ADM805M ADM802L ADM802M Reset Threshold Hysteresis Reset Timeout Delay RESET Output Voltage VBATT - 0.05
70 0.05
VCC = 0 V, VBATT = 2.8 V 5.5 V > VCC > VBATT + 0.2 V IOUT = 5 mA IOUT = 50 mA IOUT = 250 mA IOUT = 250 A, VCC < VBATT - 0.2 V Power Up Power Down
VCC - 0.01 VCC - 0.05 VCC - 0.02 VBATT - 0.002 20 -20 40
4.5 4.25 4.55 4.30 140 VCC - 1.5 0.8 VCC - 1.5
4.65 4.4
4.75 4.5 4.7 4.45 280 0.4 0.3
40 200
RESET Output Voltage
0.4 WATCHDOG TIMER Watchdog Timeout Period WDI Input Pulse Width WDI Input Threshold Logic Low Logic High WDI Input Current POWER FAIL DETECTOR PFI Input Threshold PFI Input Current PFO Output Voltage
NOTES 1 Either VCC or VBATT can be 0 V if the other > +2.0 V. Specifications subject to change without notice.
V V V V mV ms V V V V V V s ns V V A A V V nA V V
TA = 25C, VCC Falling TA = 25C, VCC Falling ISOURCE = 800 A ISINK = 3.2 mA ISINK = 100 A, VCC = 1 V ISOURCE = 4 A, VCC = 1.1 V ADM805L/M, ISOURCE = 800 A ADM805L/M, ISINK = 3.2 mA
1.0 50
1.6
2.25
VIL = 0.4, VIH = 0.8 (VCC)
0.8 3.5 10 -10 1.20 1.225 -25 VCC - 1.5 1.25 1.25 0.01 1.30 1.275 +25 0.4
WDI = VCC WDI = 0 V ADM690A, ADM692A, ADM805L/M ADM802L/M ISOURCE = 800 A ISINK = 3.2 mA
-2-
REV. 0
ADM690A/ADM692A/ADM802L/M/ADM805L/M
ABSOLUTE MAXIMUM RATINGS*
(TA = +25C unless otherwise noted)
ORDERING GUIDE
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +6 V VBATT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +6 V All Other Inputs . . . . . . . . . . . . . . . . . . -0.3 V to VCC + 0.3 V Input Current VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mA VBATT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Power Dissipation, N-8 DIP . . . . . . . . . . . . . . . . . . . 400 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 120C/W Power Dissipation, SO-8 SOIC . . . . . . . . . . . . . . . . . 500 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 110C/W Operating Temperature Range Industrial (A Version) . . . . . . . . . . . . . . . . -40C to +85C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . +300C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220C Storage Temperature Range . . . . . . . . . . . . -65C to +150C ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >4 kV
*Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended periods of time may affect device reliability.
Model ADM690AAN ADM690AARN ADM690AARM ADM692AAN ADM692AARN ADM802LAN ADM802LARN ADM802MAN ADM802MARN ADM805LAN ADM805LARN ADM805MAN ADM805MARN
Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C
PIN CONFIGURATIONS
VOUT 1 VCC 2 GND 3 PFI 4 ADM690A ADM692A ADM802L ADM802M ADM805L ADM805M
TOP VIEW (Not to Scale)
Package Option N-8 SO-8 RM-8 N-8 SO-8 N-8 SO-8 N-8 SO-8 N-8 SO-8 N-8 SO-8
8 VBATT 7 RESET (RESET) 6 WDI 5 PFO
PIN FUNCTION DESCRIPTION
Mnemonic VCC VBATT VOUT GND PFI PFO RESET
Function Power Supply Input: +5 V Nominal. Backup Battery Input. As VCC falls below the reset threshold and below VBATT by 20 mV, VBATT will be switched to VOUT. On power-up as VCC rises to 20 mV above VBATT, VOUT will be switched back to VCC. Output Voltage. When VCC is above the reset threshold, VOUT is connected to VCC through an on chip switch. When VCC is below the reset threshold, the higher of VCC or VBATT is connected to VOUT. 0 V. Ground reference for all signals. Power Fail Comparator Input. If PFI is less than 1.25 V, the power fail output PFO goes low. If unused, PFI should be connected to VCC or GND. Power Fail Comparator Output. If PFI is less than 1.25 V, the power fail output PFO goes low. Logic Output. RESET goes low if 1. VCC falls below the Reset Threshold 2. The watchdog timer is not serviced within its timeout period (1.6 seconds) The reset threshold is typically 4.65 V for the ADM690A/ADM802L/ADM805L and 4.4 V for the ADM692A/ ADM802M/ADM805M. RESET remains low for 200 ms after VCC returns above the threshold. RESET also goes low for 200 ms if the watchdog timer is enabled but not serviced within its timeout period. Active high RESET output (ADM805L/M only). This is the inverse of RESET. The asserted (high) level is VCC or VBATT whichever is higher. Watchdog Input. WDI is a three level input. If WDI remains either high or low for longer than 1.6 s, (RESET) (RESET) is activated. The timer resets with each transition on the WDI line. The watchdog timer may be disabled if WDI is left floating or is connected to a high impedance three stated logic output.
RESET WDI
REV. 0
-3-
ADM690A/ADM692A/ADM802L/M/ADM805L/M Typical Performance Curves
3
5.00 4.98
2.75 ROUT = 9.3
4.96 4.88 ROUT = 0.53
VOUT - V
2.5
VOUT - V
4.92 4.9
2.25
4.88 4.86
2 10 20 30 40 IOUT - mA 50 60 70
4.84 20 50 100 IOUT - mA 150 200
Figure 1. Output Voltage vs. Load Current in Battery Backup
Figure 4. Output Voltage vs. Load Current in Normal Operation
TA = +25 C 5V
100 90
100 90
PFO
PFO
1.3V PFI 1.2V
10 0%
10 0%
0V 1.2V
200mV
2s
1.3V PFI
200mV
2s
Figure 2. Power Fail Comparator Response Time L H
Figure 5. Power Fail Comparator Response Time H L
TA = +25 C 5V VCC
100 90
100
4V
90
RESET
10 0%
10 0%
1V
10s
1V
400ms
Figure 3. ADM690A RESET Response Time
Figure 6. RESET Output Voltage vs. VCC
-4-
REV. 0
ADM690A/ADM692A/ADM802L/M/ADM805L/M
VBATT BATTERY SWITCHOVER VCC
+5V VCC
VOUT
0V VOUT
4.65V*
RESET GENERATOR
RESET (RESET)
0V +5V RESET
3.0V
tRS
WATCHDOG INPUT (WDI)
WATCHDOG TRANSITION DETECTOR (1.6s)
POWER FAIL INPUT (PFI) 1.25V
ADM690A ADM692A ADM802L ADM802M ADM805L ADM805M
POWER FAIL OUTPUT (PFO)
0V +5V RESET 3.0V 0V +5V PFO 0V VBATT = PFI = 3.0V
*4.4V FOR ADM692A/ADM802M/ADM805M ( ) = ADM805L/M ONLY
Figure 7. Functional Block Diagram
POWER FAIL RESET, RESET
Figure 8. Timing Diagram
BATTERY SWITCHOVER SECTION
RESET is an active low output which provides a RESET signal to the microprocessor whenever VCC is at an invalid level. When VCC falls below the reset threshold, the RESET output is forced low. The nominal reset voltage threshold is 4.65 V (ADM690A/ ADM802L/ADM805L or 4.4 V ADM692A/ADM802M/ ADM805M. On power-up RESET will remain low for 200 ms after VCC rises above the reset threshold. This allows time for the power supply and microprocessor to stabilize. On power-down, the RESET output remains low with VCC as low as 1 V. This ensures that the microprocessor is held in a stable shutdown condition. The guaranteed minimum and maximum thresholds are as follows: ADM690A/ADM802L/ADM805L: 4.5 V and 4.75 V ADM692A: 4.25 V and 4.5 V. ADM802L: 4.55 V and 4.7 V ADM802M: 4.3 V and 4.45 V The ADM805L and ADM805M contain an active high reset output. This is the complement of RESET and is intended for processors requiring an active high RESET signal. The guaranteed minimum and maximum thresholds for the ADM805 are: ADM805L: 4.5 V and 4.75 V ADM805M: 4.25 V and 4.5 V.
Watchdog Timer RESET, RESET
During normal operation with VCC higher than the reset threshold, VCC is internally switched to VOUT via an internal PMOS transistor switch. This switch has a typical on-resistance of less than 1 and can supply up to 100 mA at the VOUT terminal. Once VCC falls below the reset threshold, the higher of VCC or VBATT is switched to VOUT. This means that VBATT connects to VOUT only when VCC is below the reset threshold and VBATT is greater than VCC. VOUT is normally used to drive a RAM memory bank which may require instantaneous currents of greater than 100 mA. If this is the case, then a bypass capacitor should be connected to VOUT. The capacitor will provide the peak current transients to the RAM. A capacitance value of 0.1 F or greater may be used. A 9 MOSFET switch connects the VBATT input to VOUT during battery backup. This MOSFET has very low input-tooutput differential (dropout voltage) at the low current levels required for battery backup of CMOS RAM or other low power CMOS circuitry. The supply current in battery backup is typically 0.05 A. Typically 3 V batteries are used as the backup supply. High value capacitors, either standard electrolytic or the farad size double layer capacitors, can also be used for short-term memory back up. A small charging current of typically 10 nA (0.1 A max) flows out of the VBATT terminal. This current is useful for maintaining rechargeable batteries in a fully charged condition. This extends the life of the back up battery by compensating for its self discharge current. Also note that this current poses no problem when lithium batteries are used for back up since the maximum charging current (0.1 A) is safe for even the smallest lithium cells. If the battery-switchover section is not used, VBATT should be connected to GND and VOUT should be connected to VCC.
The watchdog timer circuit monitors the activity of the microprocessor in order to check that it is not stalled in an indefinite loop. An output line on the processor is used to toggle the Watchdog Input (WDI) line. If this line is not toggled within 1.6 seconds, a RESET pulse is generated. The watchdog timeout period restarts with each transition on the WDI pin. To ensure that the watchdog timer does not time out, either a high-to-low or low-to-high transition on the WDI pin must occur at or less than the minimum timeout period. If WDI remains permanently either high or low, reset pulses will be issued after each timeout period (1.6 s). The watchdog monitor can be deactivated by floating the Watchdog Input (WDI) or by connecting it to midsupply.
REV. 0
-5-
ADM690A/ADM692A/ADM802L/M/ADM805L/M
Table I. Input and Output Status in Battery Backup Mode
INPUT POWER R1 1.25V (PFO) TO P NMI
Signal VOUT RESET RESET PFI PFO WDI
Status VOUT is connected to VBATT via an internal PMOS switch. Logic low. Logic high (ADM805L, ADM805M). The open circuit output voltage is equal to VOUT. The power fail comparator is disabled Logic low. The watchdog timer is disabled
PFI R2 R3
5V
PFO
Power Fail Comparator
The power fail comparator is an independent comparator that may be used to monitor the input power supply. The comparator's inverting input is internally connected to a 1.25 V reference voltage. The noninverting input is available at the PFI input. This input may be used to monitor the input power supply via a resistive divider network. When the voltage on the PFI input drops below 1.25 V, the comparator output (PFO) goes low indicating a power failure. For early warning of power failure the comparator may be used to monitor the preregulator input simply by choosing an appropriate resistive divider network. The PFO output can be used to interrupt the processor so that a shutdown procedure is implemented before the power is lost.
INPUT POWER R1
0V 0V VL VIN VH
VH = 1.25 1+
R2+R3 R2 x R3
1.25
R1
VL = 1.25+R1
R2
-
VCC-1.25 R3
VMID= 1.25
R1+R2 R2
Figure 10. Adding Hysteresis to the Power Fail Comparator
TYPICAL APPLICATIONS
1.25V POWER FAIL INPUT
(PFO)
POWER FAIL OUTPUT
R2
Figure 9. Power Fail Comparator
Adding Hysteresis to the Power Fail Comparator
Figure 11 shows a typical power monitoring, battery backup application. VOUT powers the CMOS RAM. Under normal operating conditions with VCC present, VOUT is internally connected to VCC. If a power failure occurs, VCC will decay and VOUT will be switched to VBATT thereby maintaining power for the CMOS RAM. A RESET pulse is also generated when VCC falls below the reset threshold.
UNREGULATED DC R1 VOUT PFI R2 VBATT + BATTERY GND RESET PFO WDI CMOS RAM POWER P SYSTEM P RESET P NMI I/O LINE +5V VCC P POWER
For increased noise immunity, hysteresis may be added to the power fail comparator. Since the comparator circuit is noninverting, hysteresis can be added simply by connecting a resistor between the PFO output and the PFI input as shown in Figure 10. When PFO is low, resistor R3 sinks current from the summing junction at the PFI pin. When PFO is high, resistor R3 sources current into the PFI summing junction. This results in differing trip levels for the comparator. Further noise immunity may be achieved by connecting a capacitor between PFI and GND.
Figure 11. Typical Application Circuit
The watchdog timer input (WDI) monitors an I/O line from the P system. This line must be toggled once every 1.6 seconds to verify correct software execution. Failure to toggle the line indicates that the P system is not correctly executing its program and may be tied up in an endless loop. If this happens, a reset pulse is generated to initialize the processor.
-6-
REV. 0
ADM690A/ADM692A/ADM802L/M/ADM805L/M
If the watchdog timer is not needed, the WDI input should be left floating. The Power Fail Input, PFI, monitors the input power supply via a resistive divider network. The voltage on the PFI input is compared with a precision 1.25 V internal reference. If the input voltage drops below 1.25 V, a power fail output (PFO) signal is generated. This warns of an impending power failure and may be used to interrupt the processor so that the system may be shut down in an orderly fashion. The resistors in the sensing network are ratioed to give the desired power fail threshold voltage VT. VT = (1.25 R1/R2) + 1.25 V R1/R2 = (VT/1.25) - 1
Alternate Watchdog Input Drive Circuits Operation Without a Backup Supply
If a backup power source is not used, VBATT should be connected to GND and VOUT should be connected to VCC.
Replacing the Backup Battery
The backup battery may be replaced without any danger of spurious resetting when VCC is present. Since VCC is above the reset threshold, a reset will not occur even if VBATT is floating while a replacement battery is being inserted. This differs from older generation products where leakage currents flowing out VBATT could cause spurious resetting during battery replacement.
Ps With Bidirectional RESET
The watchdog feature can be enabled and disabled under program control by driving WDI with a 3-state buffer. When three-stated, the WDI input will float thereby disabling the watchdog timer.
High Capacity Backup Capacitors
In order to prevent contention for microprocessors with a bidirectional reset line, a current limiting resistor should be inserted between the ADM69xA/ADM80xx RESET output pin and the P reset pin. This will limit the current to a safe level if there are conflicting output reset levels. A suitable resistor value is 4.7 k. If the reset output is required for other uses, then it should be buffered as shown in Figure 13.
BUFFERED RESET +5V
High capacity (0.1 F or greater) capacitors may be used as a backup power source. A typical application is shown in Figure 12.
+5V
VCC
ADM690A ADM692A ADM802L ADM802M
VCC VOUT TO STATIC RAM
P
RESET GND
VBATT 0.1F + GND RESET RESET* TO P
RESET GND
Figure 13. Bidirectional Reset
*FOR ADM805L/ADM805M ONLY
Figure 12. High Capacity Capacitor
REV. 0
-7-
ADM690A/ADM692A/ADM802L/M/ADM805L/M
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Pin Plastic DIP (N-8)
0.430 (10.92) 0.348 (8.84)
8 5
0.280 (7.11) 0.240 (6.10) 0.325 (8.25) 0.060 (1.52) 0.015 (0.38) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93)
1
4
PIN 1 0.210 (5.33) MAX
0.130 0.160 (4.06) (3.30) MIN 0.115 (2.93) 0.022 (0.558) 0.100 0.070 (1.77) SEATING PLANE 0.014 (0.356) (2.54) 0.045 (1.15) BSC
0.015 (0.381) 0.008 (0.204)
8-Lead SOIC (SO-8)
0.1968 (5.00) 0.1890 (4.80)
8 1 5 4
0.1574 (4.00) 0.1497 (3.80)
0.2440 (6.20) 0.2284 (5.80)
PIN 1 0.0098 (0.25) 0.0040 (0.10)
0.0688 (1.75) 0.0532 (1.35)
0.0196 (0.50) x 45 0.0099 (0.25)
SEATING PLANE
0.0500 0.0192 (0.49) (1.27) 0.0138 (0.35) BSC
0.0098 (0.25) 0.0075 (0.19)
8 0
0.0500 (1.27) 0.0160 (0.41)
8-Lead MicroSOIC (RM-8)
0.122 (3.10) 0.114 (2.90)
8
5
0.122 (3.10) 0.114 (2.90)
1 4
0.199 (5.05) 0.187 (4.75)
PIN 1 0.0256 (0.65) BSC 0.120 (3.05) 0.112 (2.84) 0.006 (0.15) 0.002 (0.05) SEATING PLANE 0.018 (0.46) 0.008 (0.20) 0.043 (1.09) 0.037 (0.938) 0.011 (0.28) 0.003 (0.08) 33 27 0.027 (0.68) 0.015 (0.38) 0.120 (3.05) 0.112 (2.84)
-8-
REV. 0
PRINTED IN U.S.A.
C2197-12-10/96


▲Up To Search▲   

 
Price & Availability of ADM690A

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X