View PI3A412EZLE_961148.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PI3A412E
0.5, 3.3V, Quad SPDT Analog Switch with Enable
Features
* CMOS Technology for Bus and Analog Applications * Low On-Resistance: 0.5 (+2.7V Supply) * Wide VCC Range: +1.65V to +4.2V 10% * ICC = 0.3A @ TA = +25C * Rail-to-Rail switching throughout Signal Range * Fast Switching Speed: 20ns max. at 3.3V * High Off Isolation: -65dB @ 100 kHz * Crosstalk Rejection: -65dB @ 100 kHz * Extended Industrial Temperature Range: -40C to 85C * Packaging ( Pb-free & Green): - 16-contact TQFN (ZL16), 2.5mm x 2.5mm - 16-contact TQFN (ZH16), 3.0mm x 3.0mm
Description
The PI3A412E is a Quad single-pole double-throw (SPDT) CMOS switch with enable. It can be used as an analog switch or as a lowdelay bus switch. Specified over a wide operating power supply voltage range, +1.65V to +4.2V, the switch has an On-Resistance of 0.5 at 2.7V. Control inputs, A0 to EN, tolerates input drive signals up to 5V, independent of supply voltage.
Block Diagram / Pin Configuration (top view)
COM1
NO1
NC4
VCC
Applications
* Cell Phones * PDAs * Portable Instrumentation * Battery Powered Communications * Computer Peripherals * Audio & Video Signal Routing * PCMCIA Cards * Modems * Hard Drives * JTAG Testing
16 15 14 13 12 11
NC1 A0 NO2 COM2
1 2
COM4 NO4 EN NC3
GND
3 4 5 6 7 8 10 9
NC2
GND
NO3
COM3
Pin Description
Pin # 4, 8, 12, 16 1, 5, 9, 13 3, 7, 11, 15 10 2 6 14
Note : 1. X = 1, 2, 3, or 4
Function Table
Name COMX NCX NOX EN A0 GND VCC Description Common Output / Data Port Data Port (normally connect) Data Port (normally open) Enable Logic Input Control Ground Positive Power Supply EN 1 0 0 A0 X 0 1 Function No Switch Connected, All I/O = Hi-Z NCx Connected to COMx NOx Connected to COMx
Note : 1. X = 1, 2, 3, or 4.
06-0322
1
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable Absolute Maximum Ratings
Voltages Referenced to GND VCC .................................................................... -0.5V to +4.6V VNC, VNO, VCOM (1) ....................................-0.5V to V+ +0.3V .................................................or 30mA, whichever occurs first Current (any terminal)................................................... 400mA Peak Current (Pulsed at 1ms, 10% duty cycle)................................... 500mA
Thermal Information
Continuous Power Dissipation 16-pin Tin TQFN (derate 7.1mW/C above +70C) ........... 0.5W Storage Temperature ........................................ -65C to +150C Lead Temperature (soldering, 10s) ................................. +300C
Note 1: Signals on NC, NO, COM, or EN1, A0 exceeding VCC or GND are clamped by internal diodes. Limit forward diode current to 30mA.
Caution: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied.
Electrical Specifications - Single +4.2V Supply
(VCC = +4.2V 10%, GND = 0V, VIH = 1.4V, VIL = 0.7V) (TA = -40C to +85C) Parameter Analog Switch Analog Signal Range (3) On Resistance On-Resistance Match Between Channels(4) On-Resistance Flatness(5) Off Leakage Current(6) On Leakage Current
(6)
Symbol VANALOG RON RON RFLAT(ON) INO(OFF), or INC(OFF) ICOM(ON)
Conditions
Min.(1) 0
Typ. (2)
Max. (1) Units VCC V
VCC = 4.0V, ICOM = 100mA, VNC = +1.5V VCC = 4.0V, ICOM = 100mA, VNC = 0.8V, 2.0V VCC = 4.4V, VNO or VNC = 0.3V, 3.3V VCC = 4.4V, VNO or VNC = 0.3V, 3.3V -200 -200
0.4 0.01 0.06
0.5 0.03 0.15 200 nA 200
Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are TA = 25C, VCC = 4.2V unless otherwise specified. 3. Guaranteed by design. 4. RON = RON match between channels 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25C.
06-0322
2
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable Electrical Specifications - Single +4.2V Supply
(VCC = +4.2V 10%, GND = 0V, VIH = 1.4V, VIL = 0.7V) (TA = -40C to +85C) Description Logic Input Input High Voltage Input Low Voltage Input Current with Voltage High Input Current with Voltage Low Dynamic Turn-On Time Turn-Off Time Break-Before-Make Charge Injection(3) Off Isolation(4) Cross Talk
(5)
Parameters
Test Conditions
Min.(1)
Typ.(2)
Max.(1)
Units
VIH VIL IAH IAL
Guaranteed logic High Level Guaranteed logic Low Level VA = 1.4V, all others = 0.5V VA = 0.5V, all other = 1.4V
1.4 0.7 -1 -1 1 1
V A
tON tOFF tBBM Q OIRR XTALK f3db CNO(OFF) CNC(OFF) CON
VCC = 4.2V, VNO = 2.0V, Figure 1 & 2 VNO = 1.5V, RL = 50, CL = 35pF, See Figure 3 CL = 1nF, VGEN = 0V, RGEN = 0, Figure 4 RL = 50, f = 100 kHz, Figure 5 RL = 50, f = 100 kHz, Figure 6 See Test Circuit Figure 9 f = 1 MHz, Figure 7 f = 1 MHz, Figure 8 1
20 12 12 100 -65
25 15 ns 15 pC
dB -65 40 45 45 150 pF MHz
3dB Bandwidth Off Capacitance Off Capacitance On Capacitance Supply Power-Supply Range Positve Supply Current
VCC ICC VCC = 4.4V, VCOM = 0V or VCC
1.5
4.6 0.4
V A
Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are VCC = 4.2V unless otherwise specified. 3. Guaranteed by design. 4. Off Isolation = 20log10 [ VCOM / (VNO or VNC) ]. See Figure 4. 5. Between any two switches. See Figure 5.
06-0322
3
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable Electrical Specifications - Single +3.3V Supply
(VCC = +3.3V 10%, GND = 0V, VIH = 1.3V, VIL = 0.5V) (TA = -40C to +85C) Parameter Analog Switch Analog Signal Range (3) On Resistance On-Resistance Match Between Channels(4) On-Resistance Flatness(5) Off Leakage Current(6) On Leakage Current
(6)
Symbol VANALOG RON RON RFLAT(ON) INO(OFF), or INC(OFF) ICOM(ON)
Conditions
Min.(1) 0
Typ. (2)
Max. (1) Units VCC V
VCC = 2.7V, ICOM = 100mA, VNC = +1.5V VCC = 2.7V, ICOM = 100mA, VNC = 0.8V, 2.0V VCC = 3.6V, VNO or VNC = 0.3V, 3.3V VCC = 3.6V, VNO or VNC = 0.3V, 3.3V -150 -150
0.5 0.02 0.05
0.65 0.05 0.15 150 nA 150
Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are VCC = 3.3V unless otherwise specified. 3. Guaranteed by design. 4. RON = RON match between channels 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25C.
06-0322
4
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable Electrical Specifications - Single +3.3V Supply
(VCC = +3.3V 10%, GND = 0V, VIH = 1.3V, VIL = 0.5V) (TA = -40C to +85C) Description Logic Input Input High Voltage Input Low Voltage Input Current with Voltage High Input Current with Voltage Low Dynamic Turn-On Time Turn-Off Time Break-Before-Make Charge Injection(3) Off Isolation(4) Cross Talk
(5)
Parameters
Test Conditions
Min.(1)
Typ.(2)
Max.(1)
Units
VIH VIL IAH IAL
Guaranteed logic High Level Guaranteed logic Low Level VA = 1.4V, all others = 0.5V VA = 0.5V, all other = 1.4V
1.3 0.5 -1 -1 1
V
A 1
tON tOFF tBBM Q OIRR XTALK f3db CNO(OFF) CNC(OFF) CON
VCC = 3.3V, VNO = 2.0V, Figure 1 & 2 VNO = 1.5V, RL = 50, CL = 35pF, See Figure 3 CL = 1nF, VGEN = 0V, RGEN = 0, Figure 4 RL = 50, f = 100 kHz, Figure 5 RL = 50, f = 100 kHz, Figure 6 See Test Circiut Figure 9 f = 1 MHz, Figure 7 f = 1 MHz, Figure 8 1
20 12 12 100 -65
25 15 ns 15 pC
dB -65 40 45 45 150 pF MHz
3dB Bandwidth Off Capacitance Off Capacitance On Capacitance Supply Power-Supply Range Positve Supply Current
VCC ICC VCC = 3.6V, VCOM = 0V or VCC
1.5
4.6 0.3
V A
Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are TA = 25C, VCC = 3.3V unless otherwise specified. 3. Guaranteed by design. 4. Off Isolation = 20log10 [ VCOM / (VNO or VNC) ]. See Figure 4. 5. Between any two switches. See Figure 5.
06-0322
5
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable Test Circuits and Timing Diagrams
VCC VCC NO RL 50 GND
VCOM
COMx
VOUT CL
35pF
A LOGIC INPUT
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
Notes: Unused BX inputs must be grounded.
Figure 1. AC Test Circuit
Logic Input
VIH VIL Off 50% On VOUT Off tOFF 90% tON Logic Input Waveforms inverted for Switches that have opposite logic 1.5V for 3.3V Supply 90%
tr < 5ns tf < 5ns
Switch Output 0V
Figure 2. AC Waveforms
VIN
NO COM NC RL A
50
VOUT CL
35pF
Logic Input V OUT
50%
0.9 x V OUT t BBM
Logic Input
Figure 3. Break Before Make Interval Timing
06-0322
6
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable
RGEN
NO or NC
COM VOUT CL 1nF
Logic Input
OFF
ON
OFF V OUT
VGEN A Logic Input
Q = (V OUT )(CL )
Figure 4. Charge Injection Test
VCC 10nF
10nF
VCC
50 COM VCC Logic Input 0V or VIH
Signal Generator
50 NC NO
VCC COM 50
Signal Generator
NO or NC GND RL 50 A
Analyzer
Analyzer
GND RL 50
A
CL = 5pF
CL = 5pF
Figure 5. Off Isolation
Figure 6. Crosstalk
VCC 10nF
VCC 10nF
COM Capacitance Meter f = 1 MHz NC
VCC Logic Input 0V or VIH
Capacitance Meter f = 1 MHz
NO or NC
VCC Logic Input 0V or VIH
A
A COM GND
GND
Figure 7. Channel Off Capacitance
Figure 8. Channel On Capacitance
06-0322
7
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable
VCC 10nF
50 NC Signal Generator A Logic Input 0V or VIH
VCC COM 50
ANALYZER
GND
Figure 9. Bandwidth
06-0322
8
PS8804B
12/06/06
PI3A412E 0.5, 3.3V, Quad SPDT Analog Switch with Enable
Ordering Information
Ordering Code PI3A412EZLE PI3A412EZHE Package Code ZL ZH Package Description Pb-free & Green, 16-contact TQFN Pb-free & Green, 16-contact TQFN
Notes: * Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ * E = Pb-free and Green * Adding X suffix = Tape/Reel
Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com
06-0322
9
PS8804B
12/06/06

▲Up To Search▲

Price & Availability of PI3A412EZLE

	To Download PI3A412EZLE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .