|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
56F8367/56F8167 Data Sheet Preliminary Technical Data 56F8300 16-bit Digital Signal Controllers MC56F8367 Rev. 3.0 09/2005 freescale.com Document Revision History Version History Rev 0 Rev 1.0 Rev 2.0 Description of Change Pre-release, Alpha customers only Initial Public Release Added output voltage maximum value and note to clarify in Table 10-1.; also removed overall life expectancy note, since life expectancy is dependent on customer usage and must be determined by reliability engineering. Clarified value and unit measure for Maximum allowed PD in Table 10-3. Corrected note about average value for Flash Data Retention in Table 10-4. Added new RoHS-compliant orderable part numbers in Table 13-1. Added 160MAPBGA information, TA equation updated in Table 10-4 and additional minor edits throughout data sheet Rev 3.0 Please see http://www.freescale.com for the most current Data Sheet revision. 56F8367 Technical Data, Rev. 3.0 2 Freescale Semiconductor Preliminary 56F8367/56F8167 General Description Note: Features in italics are NOT available in the 56F8167 device. * Up to 60 MIPS at 60MHz core frequency * DSP and MCU functionality in a unified, C-efficient architecture * Access up to 4MB of off-chip program and 32MB of data memory * Chip Select Logic for glueless interface to ROM and SRAM * 512KB of Program Flash * 4KB of Program RAM * 32KB of Data Flash * 32KB of Data RAM * 32KB Boot Flash * Up to two 6-channel PWM modules * Four 4-channel, 12-bit ADCs OCR_DIS RSTO EMI_MODE EXTBOOT 5 VPP 2 VCAP 4 VDD 7 VSS 6 Digital Reg VDDA 2 Analog Reg VSSA RESET 6 3 4 6 3 4 4 4 5 4 4 PWM Outputs Current Sense Inputs or GPIOC Fault Inputs PWM Outputs Current Sense Inputs or GPIOD Fault Inputs AD0 AD1 VREF AD0 AD1 * Configuration shown for on-chip 2.5V regulator * Temperature Sensor * Up to two Quadrature Decoders * Optional on-chip regulator * Up to two FlexCAN modules * Two Serial Communication Interfaces (SCIs) * Up to two Serial Peripheral Interfaces (SPIs) * Up to four general-purpose Quad Timers * Computer Operating Properly (COP) / Watchdog * JTAG/Enhanced On-Chip Emulation (OnCETM) for unobtrusive, real-time debugging * Up to 76 GPIO lines * 160-pin LQFP Package and 160 MAPBGA PWMA JTAG/ EOnCE Port 16-Bit 56800E Core Low Voltage Supervisor Bit Manipulation Unit PWMB Program Controller and Hardware Looping Unit Address Generation Unit Data ALU 16 x 16 + 36 -> 36-Bit MAC Three 16-bit Input Registers Four 36-bit Accumulators ADCA PAB PDB CDBR CDBW Memory ADCB Program Memory 256K x 16 Flash 2K x 16 RAM Boot ROM 16K x 16 Flash R/W Control XDB2 XAB1 XAB2 External Address Bus Switch 6 2 8 4 3 External Data Bus Switch A0-5 or GPIOA8-13 A6-7 or GPIOE2-3 A8-15 or GPIOA0-7 GPIOB0-3 (A16-19) GPIOB4 (A20, prescaler_clock) GPIOB5-7 (A21-23, clk0-3**) D0-6 or GPIOF9-15 D7-15 or GPIOF0-8 WR RD GPIOD2-5 or CS4 -7 PS / CS0 (GPIOD8) DS / CS1 (GPIOD9) Temp_Sense Quadrature Decoder 0 or Quad Timer A or GPIOC Quadrature Decoder 1 or Quad Timer B or SPI1 or GPIOC Quad Timer C or GPIOE Quad Timer D or GPIOE FlexCAN Data Memory 16K x 16 Flash 4K x 16 Flash 4 PDB CDBR CDBW External Bus Interface Unit PAB System Bus Control 7 9 4 IPBus Bridge (IPBB) Decoding Peripherals Clock resets Bus Control 4 2 Peripheral Device Selects RW Control IPAB IPWDB IPRDB GPIO or EMI CS or FlexCAN2 GPIOD0 (CS2 or CAN2_TX) GPIOD1 (CS3 or CAN2_RX) 4 2 PLL SPI0 or GPIOE 4 SCI1 or GPIOD 2 SCI0 or GPIOE 2 COP/ Watchdog Interrupt Controller System O Integration R Module CLKO P O Clock Generator S C XTAL EXTAL **See Table 2-2 for explanation IRQA IRQB CLKMODE 56F8367/56F8167 Block Diagram 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 3 Table of Contents Part 1: Overview . . . . . . . . . . . . . . . . . . . . . . . 5 1.1. 1.2. 1.3. 1.4. 1.5. 1.6. 56F8367/56F8167 Features . . . . . . . . . . . . . 5 Device Description . . . . . . . . . . . . . . . . . . . . 7 Award-Winning Development Environment . 9 Architecture Block Diagram . . . . . . . . . . . . . 10 Product Documentation . . . . . . . . . . . . . . . . 14 Data Sheet Conventions . . . . . . . . . . . . . . . 14 Part 8: General Purpose Input/Output (GPIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 8.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 132 8.2. Memory Maps . . . . . . . . . . . . . . . . . . . . . . 132 8.3. Configuration. . . . . . . . . . . . . . . . . . . . . . . 132 Part 9: Joint Test Action Group (JTAG) . 137 9.1. 56F8367 Information . . . . . . . . . . . . . . . . . 137 Part 2: Signal/Connection Descriptions . . . 15 2.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.2. Signal Pins . . . . . . . . . . . . . . . . . . . . . . . . . 18 Part 10: Specifications . . . . . . . . . . . . . . . 137 10.1. General Characteristics . . . . . . . . . . . . . .137 10.2. DC Electrical Characteristics . . . . . . . . . . 141 10.3. AC Electrical Characteristics . . . . . . . . . . 145 10.4. Flash Memory Characteristics . . . . . . . . . 145 10.5. External Clock Operation Timing . . . . . . 146 10.6. Phase Locked Loop Timing . . . . . . . . . . .146 10.7. Crystal Oscillator Timing . . . . . . . . . . . . . 147 10.8. External Memory Interface Timing . . . . . .147 10.9. Reset, Stop, Wait, Mode Select, and Interrupt Timing . . . . . . . . . . . . . . . . . . . . . 150 10.10. Serial Peripheral Interface (SPI) Timing . 152 10.11. Quad Timer Timing . . . . . . . . . . . . . . . . 156 10.12. Quadrature Decoder Timing . . . . . . . . . . 156 10.13. Serial Communication Interface (SCI) Timing . . . . . . . . . . . . . . . . 157 10.14. Controller Area Network (CAN) Timing . 158 10.15. JTAG Timing . . . . . . . . . . . . . . . . . . . . . 158 10.16. Analog-to-Digital Converter (ADC) Parameters . . . . . . . . . . . . 160 10.17. Equivalent Circuit for ADC Inputs . . . . . .163 10.18. Power Consumption . . . . . . . . . . . . . . . 163 Part 3: On-Chip Clock Synthesis (OCCS) . . 38 3.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 38 3.2. External Clock Operation . . . . . . . . . . . . . . 38 3.3. Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Part 4: Memory Operating Modes (MEM) . . 40 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. 4.7. 4.8. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . Program Map. . . . . . . . . . . . . . . . . . . . . . . . Interrupt Vector Table . . . . . . . . . . . . . . . . . Data Map . . . . . . . . . . . . . . . . . . . . . . . . . . Flash Memory Map . . . . . . . . . . . . . . . . . . . EOnCE Memory Map . . . . . . . . . . . . . . . . . Peripheral Memory Mapped Registers . . . . Factory Programmed Memory . . . . . . . . . . 40 41 42 46 46 48 49 79 Part 5: Interrupt Controller (ITCN) . . . . . . . . 80 5.1. 5.2. 5.3. 5.4. 5.5. 5.6. 5.7. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 80 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Functional Description . . . . . . . . . . . . . . . . . 80 Block Diagram . . . . . . . . . . . . . . . . . . . . . . 82 Operating Modes . . . . . . . . . . . . . . . . . . . . 82 Register Descriptions . . . . . . . . . . . . . . . . . 83 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Part 11: Packaging . . . . . . . . . . . . . . . . . . . 165 11.1. 56F8367 Package and Pin-Out Information 165 11.2. 56F8167 Package and Pin-Out Information 172 Part 6: System Integration Module (SIM) . 110 6.1. 6.2. 6.3. 6.4. 6.5. 6.6. 6.7. 6.8. 6.9. Overview . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Modes . . . . . . . . . . . . . . . . . . . Operating Mode Register . . . . . . . . . . . . . Register Descriptions . . . . . . . . . . . . . . . . Clock Generation Overview. . . . . . . . . . . . Power Down Modes Overview . . . . . . . . . Stop and Wait Mode Disable Function . . . Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 110 111 111 112 126 127 128 128 Part 12: Design Considerations . . . . . . . . 176 12.1. Thermal Design Considerations . . . . . . . . 176 12.2. Electrical Design Considerations . . . . . . . 177 12.3. Power Distribution and I/O Ring 12.4. Implementation . . . . . . . . . . . . . . . . . . . . . 178 Part 13: Ordering Information . . . . . . . . . 179 Part 7: Security Features . . . . . . . . . . . . . . 129 7.1. Operation with Security Enabled . . . . . . . . 129 7.2. Flash Access Blocking Mechanisms . . . . . 129 56F8367 Technical Data, Rev. 3.0 4 Freescale Semiconductor Preliminary 56F8367/56F8167 Features Part 1 Overview 1.1 56F8367/56F8167 Features 1.1.1 * * * * * * * * * * * * * * Core Efficient 16-bit 56800E family controller engine with dual Harvard architecture Up to 60 Million Instructions Per Second (MIPS) at 60MHz core frequency Single-cycle 16 x 16-bit parallel Multiplier-Accumulator (MAC) Four 36-bit accumulators, including extension bits Arithmetic and logic multi-bit shifter Parallel instruction set with unique DSP addressing modes Hardware DO and REP loops Three internal address buses and one external address bus Four internal data buses and one external data bus Instruction set supports both DSP and controller functions Controller-style addressing modes and instructions for compact code Efficient C compiler and local variable support Software subroutine and interrupt stack with depth limited only by memory JTAG/EOnCE debug programming interface 1.1.2 Differences Between Devices Table 1-1 outlines the key differences between the 56F8367 and 56F8167 devices. Table 1-1 Device Differences Feature Guaranteed Speed Program RAM Data Flash PWM CAN Quad Timer Quadrature Decoder Temperature Sensor Dedicated GPIO 56F8367 60MHz/60 MIPS 4KB 32KB 2x6 2 4 2x4 1 -- 56F8167 40MHZ/40MIPS Not Available Not Available 1x6 Not Available 2 1x4 Not Available 7 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 5 1.1.3 * * * Memory Harvard architecture permits as many as three simultaneous accesses to program and data memory Flash security protection feature On-chip memory, including a low-cost, high-volume Flash solution -- 512KB of Program Flash -- 4KB of Program RAM -- 32KB of Data Flash -- 32KB of Data RAM -- 32KB of Boot Flash Note: Features in italics are NOT available in the 56F8167 device. * Off-chip memory expansion capabilities provide a simple method for interfacing additional external memory and/or peripheral devices -- Access up to 4MB of external program memory or 32MB of external data memory -- Chip select logic for glueless interface to ROM and SRAM EEPROM emulation capability * 1.1.4 * Peripheral Circuits Pulse Width Modulator: -- In the 56F8367, two Pulse Width Modulator modules, each with six PWM outputs, three Current Sense inputs, and three Fault inputs; fault-tolerant design with dead time insertion; supports both center-aligned and edge-aligned modes -- In the 56F8167, one Pulse Width Modulator module, with six PWM outputs, three Current Sense inputs, and three Fault inputs; fault-tolerant design with dead time insertion; supports both center-aligned and edge-aligned modes Note: Features in italics are NOT available in the 56F8167 device. * * Four 12-bit, Analog-to-Digital Converters (ADCs), which support four simultaneous conversions with quad, 4-pin multiplexed inputs; ADC and PWM modules can be synchronized through Timer C, channels 2 and 3 Quadrature Decoder: -- In the 56F8367, two four-input Quadrature Decoders or two additional Quad Timers -- In the 56F8167, one four-input Quadrature Decoder, which works in conjunction with Quad Timer A Temperature Sensor can be connected, on the board, to any of the ADC inputs to monitor the on-chip temperature Quad Timer: -- In the 56F8367, four dedicated general-purpose Quad Timers totaling six dedicated pins: Timer C with two pins and Timer D with four pins -- In the 56F8167, two general-purpose Quad Timers; Timer A works in conjunction with Quadrature Decoder 0 or GPIO and Timer C works in conjunction with GPIO * * * Up to two FlexCAN (CAN Version 2.0 B-compliant ) modules with 2-pin port for transmit and receive 56F8367 Technical Data, Rev. 3.0 6 Freescale Semiconductor Preliminary Device Description * * Two Serial Communication Interfaces (SCIs), each with two pins (or four additional GPIO lines) Up to two Serial Peripheral Interfaces (SPIs), both with configurable 4-pin port (or eight additional GPIO lines) -- In the 56F8367, SPI1 can also be used as Quadrature Decoder 1, Quad Timer B or GPIO -- In the 56F8167, SPI1 can alternately be used only as GPIO Computer Operating Properly (COP) / Watchdog timer Two dedicated external interrupt pins Up to 76 General Purpose I/O (GPIO) pins External reset input pin for hardware reset External reset output pin for system reset Integrated Low-Voltage Interrupt Module JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, processor speed-independent debugging Software-programmable, Phase Lock Loop (PLL)-based frequency synthesizer for the core clock * * * * * * * * 1.1.5 * * * * * * Energy Information Fabricated in high-density CMOS with 5V-tolerant, TTL-compatible digital inputs On-board 3.3V down to 2.6V voltage regulator for powering internal logic and memories; can be disabled On-chip regulators for digital and analog circuitry to lower cost and reduce noise Wait and Stop modes available ADC smart power management Each peripheral can be individually disabled to save power 1.2 Device Description The 56F8367 and 56F8167 are members of the 56800E core-based family of controllers. Each combines, on a single chip, the processing power of a Digital Signal Processor (DSP) and the functionality of a microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because of its low cost, configuration flexibility, and compact program code, the 56F8367 and 56F8167 are well-suited for many applications. The device includes many peripherals that are especially useful for motion control, smart appliances, steppers, encoders, tachometers, limit switches, power supply and control, automotive control (56F8367 only), engine management, noise suppression, remote utility metering, industrial control for power, lighting, and automation applications. The 56800E core is based on a Harvard-style architecture consisting of three execution units operating in parallel, allowing as many as six operations per instruction cycle. The MCU-style programming model and optimized instruction set allow straightforward generation of efficient, compact DSP and control code. The instruction set is also highly efficient for C/C++ Compilers to enable rapid development of optimized control applications. The 56F8367 and 56F8167 support program execution from internal or external memories. Two data operands can be accessed from the on-chip data RAM per instruction cycle. These devices also provide two external dedicated interrupt lines and up to 76 General Purpose Input/Output (GPIO) lines, depending on peripheral configuration. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 7 1.2.1 56F8367 Features The 56F8367 controller includes 512KB of Program Flash and 32KB of Data Flash (each programmable through the JTAG port) with 4KB of Program RAM and 32KB of Data RAM. It also supports program execution from external memory. A total of 32KB of Boot Flash is incorporated for easy customer inclusion of field-programmable software routines that can be used to program the main Program and Data Flash memory areas. Both Program and Data Flash memories can be independently bulk erased or erased in page sizes. Program Flash page erase size is 1KB. Boot and Data Flash page erase size is 512 bytes. The Boot Flash memory can also be either bulk or page erased. A key application-specific feature of the 56F8367 is the inclusion of two Pulse Width Modulator (PWM) modules. These modules each incorporate three complementary, individually programmable PWM signal output pairs (each module is also capable of supporting six independent PWM functions, for a total of 12 PWM outputs) to enhance motor control functionality. Complementary operation permits programmable dead time insertion, distortion correction via current sensing by software, and separate top and bottom output polarity control. The up-counter value is programmable to support a continuously variable PWM frequency. Edge-aligned and center-aligned synchronous pulse width control (0% to 100% modulation) is supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors); both BDC and BLDC (Brush and Brushless DC motors); SRM and VRM (Switched and Variable Reluctance Motors); and stepper motors. The PWMs incorporate fault protection and cycle-by-cycle current limiting with sufficient output drive capability to directly drive standard optoisolators. A "smoke-inhibit", write-once protection feature for key parameters is also included. A patented PWM waveform distortion correction circuit is also provided. Each PWM is double-buffered and includes interrupt controls to permit integral reload rates to be programmable from 1 to 16. The PWM modules provide a reference output to synchronize the Analog-to-Digital Converters through two channels of Quad Timer C. The 56F8367 incorporates two Quadrature Decoders capable of capturing all four transitions on the two-phase inputs, permitting generation of a number proportional to actual position. Speed computation capabilities accommodate both fast- and slow-moving shafts. An integrated watchdog timer in the Quadrature Decoder can be programmed with a time-out value to alarm when no shaft motion is detected. Each input is filtered to ensure only true transitions are recorded. This controller also provides a full set of standard programmable peripherals that include two Serial Communications Interfaces (SCIs); two Serial Peripheral Interfaces (SPIs); and four Quad Timers. Any of these interfaces can be used as General Purpose Input/Outputs (GPIOs) if that function is not required. Two Flex Controller Area Network (FlexCAN) interfaces (CAN Version 2.0 B-compliant) and an internal interrupt controller are a part of the 56F8367. 1.2.2 56F8167 Features The 56F8167 controller includes 128KB of Program Flash, programmable through the JTAG port, with 8KB of Data RAM. It also supports program execution from external memory. A total of 8KB of Boot Flash is incorporated for easy customer inclusion of field-programmable software routines that can be used to program the main Program Flash memory area, which can be independently 56F8367 Technical Data, Rev. 3.0 8 Freescale Semiconductor Preliminary Award-Winning Development Environment bulk erased or erased in pages. Program Flash page erase size is 1KB. Boot Flash page erase size is 512 bytes and the Boot Flash memory can also be either bulk or page erased. A key application-specific feature of the 56F8167 is the inclusion of one Pulse Width Modulator (PWM) module. This module incorporates three complementary, individually programmable PWM signal output pairs and can also support six independent PWM functions to enhance motor control functionality. Complementary operation permits programmable dead time insertion, distortion correction via current sensing by software, and separate top and bottom output polarity control. The up-counter value is programmable to support a continuously variable PWM frequency. Edge-aligned and center-aligned synchronous pulse width control (0% to 100% modulation) is supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors); both BDC and BLDC (Brush and Brushless DC motors); SRM and VRM (Switched and Variable Reluctance Motors); and stepper motors. The PWM incorporates fault protection and cycle-by-cycle current limiting with sufficient output drive capability to directly drive standard optoisolators. A "smoke-inhibit", write-once protection feature for key parameters is also included. A patented PWM waveform distortion correction circuit is also provided. Each PWM is double-buffered and includes interrupt controls to permit integral reload rates to be programmable from 1 to 16. The PWM module provides reference outputs to synchronize the Analog-to-Digital Converters through two channels of Quad Timer C. The 56F8167 incorporates a Quadrature Decoder capable of capturing all four transitions on the two-phase inputs, permitting generation of a number proportional to actual position. Speed computation capabilities accommodate both fast- and slow-moving shafts. An integrated watchdog timer in the Quadrature Decoder can be programmed with a time-out value to alert when no shaft motion is detected. Each input is filtered to ensure only true transitions are recorded. This controller also provides a full set of standard programmable peripherals that include two Serial Communications Interfaces (SCIs); two Serial Peripheral Interfaces (SPIs); and two Quad Timers. Any of these interfaces can be used as General Purpose Input/Outputs (GPIOs) if that function is not required. An internal interrupt controller is also a part of the 56F8167. 1.3 Award-Winning Development Environment Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use component-based software application creation with an expert knowledge system. The CodeWarrior Integrated Development Environment is a sophisticated tool for code navigation, compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards will support concurrent engineering. Together, PE, CodeWarrior and EVMs create a complete, scalable tools solution for easy, fast, and efficient development. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 9 1.4 Architecture Block Diagram Note: Features in italics are NOT available in the 56F8167 device and are shaded in the following figures. The 56F8367/56F8167 architecture is shown in Figure 1-1 and Figure 1-2. Figure 1-1 illustrates how the 56800E system buses communicate with internal memories, the external memory interface and the IPBus Bridge. Table 1-2 lists the internal buses in the 56800E architecture and provides a brief description of their function. Figure 1-2 shows the peripherals and control blocks connected to the IPBus Bridge. The figures do not show the on-board regulator and power and ground signals. They also do not show the multiplexing between peripherals or the dedicated GPIOs. Please see Part 2, Signal/Connection Descriptions, to see which signals are multiplexed with those of other peripherals. Also shown in Figure 1-2 are connections between the PWM, Timer C and ADC blocks. These connections allow the PWM and/or Timer C to control the timing of the start of ADC conversions. The Timer C channel indicated can generate periodic start (SYNC) signals to the ADC to start its conversions. In another operating mode, the PWM load interrupt (SYNC output) signal is routed internally to the Timer C input channel as indicated. The timer can then be used to introduce a controllable delay before generating its output signal. The timer output then triggers the ADC. To fully understand this interaction, please see the 56F8300 Peripheral User Manual for clarification on the operation of all three of these peripherals. 56F8367 Technical Data, Rev. 3.0 10 Freescale Semiconductor Preliminary Architecture Block Diagram 5 JTAG / EOnCE Boot Flash pdb_m[15:0] pab[20:0] Program Flash Program RAM cdbw[31:0] 56800E CHIP TAP Controller 24 EMI 16 10 Address Data Control TAP Linking Module xab1[23:0] xab2[23:0] Data RAM External JTAG Port cdbr_m[31:0] xdb2_m[15:0] Data Flash IPBus Bridge To Flash Control Logic NOT available on the 56F8167 device. IPBus Flash Memory Module Figure 1-1 System Bus Interfaces Note: Flash memories are encapsulated within the Flash Memory (FM) Module . Flash control is accomplished by the I/O to the FM over the peripheral bus, while reads and writes are completed between the core and the Flash memories. The primary data RAM port is 32 bits wide. Other data ports are 16 bits. Note: 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 11 To/From IPBus Bridge CLKGEN (OSC/PLL) Interrupt Controller Low Voltage Interrupt Timer A POR & LVI 4 4 Quadrature Decoder 0 Timer D System POR SIM COP Reset RESET Timer B COP 4 Quadrature Decoder 1 SPI 1 FlexCAN FlexCAN2 13 2 2 PWMA GPIO A GPIO B GPIO C GPIO D GPIO E GPIO F 4 2 2 13 SYNC Output PWMB SYNC Output ch3i ch2i Timer C ch3o ch2o 2 ADCB SPI 0 SCI 0 SCI 1 IPBus 8 ADCA TEMP_SENSE 8 1 NOT available on the 56F8167 device. Note: ADC A and ADC B use the same voltage reference circuit with VREFH, VREFP, VREFMID, VREFN, and VREFLO pins. Figure 1-2 Peripheral Subsystem 56F8367 Technical Data, Rev. 3.0 12 Freescale Semiconductor Preliminary Architecture Block Diagram Table 1-2 Bus Signal Names Name pdb_m[15:0] cdbw[15:0] pab[20:0] Function Program Memory Interface Program data bus for instruction word fetches or read operations. Primary core data bus used for program memory writes. (Only these 16 bits of the cdbw[31:0] bus are used for writes to program memory.) Program memory address bus. Data is returned on pdb_m bus. Primary Data Memory Interface Bus cdbr_m[31:0] Primary core data bus for memory reads. Addressed via xab1 bus. cdbw[31:0] xab1[23:0] Primary core data bus for memory writes. Addressed via xab1 bus. Primary data address bus. Capable of addressing bytes1, words, and long data types. Data is written on cdbw and returned on cdbr_m. Also used to access memory-mapped I/O. Secondary Data Memory Interface xdb2_m[15:0] Secondary data bus used for secondary data address bus xab2 in the dual memory reads. xab2[23:0] Secondary data address bus used for the second of two simultaneous accesses. Capable of addressing only words. Data is returned on xdb2_m. Peripheral Interface Bus IPBus [15:0] Peripheral bus accesses all on-chip peripherals registers. This bus operates at the same clock rate as the Primary Data Memory and therefore generates no delays when accessing the processor. Write data is obtained from cdbw. Read data is provided to cdbr_m. 1. Byte accesses can only occur in the bottom half of the memory address space. The MSB of the address will be forced to 0. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 13 1.5 Product Documentation The documents in Table 1-2 are required for a complete description and proper design with the 56F8367/56F8167 devices. Documentation is available from local Freescale distributors, Freescale semiconductor sales offices, Freescale Literature Distribution Centers, or online at http://www.freescale.com. Table 1-3 Chip Documentation Topic DSP56800E Reference Manual 56F8300 Peripheral User Manual 56F8300 SCI/CAN Bootloader User Manual 56F8367/56F8167 Technical Data Sheet Errata Description Detailed description of the 56800E family architecture, and 16-bit controller core processor and the instruction set Detailed description of peripherals of the 56F8300 devices Detailed description of the SCI/CAN Bootloaders 56F8300 family of devices Electrical and timing specifications, pin descriptions, and package descriptions (this document) Details any chip issues that might be present Order Number DSP56800EERM MC56F8300UM MC56F83xxBLUM MC56F8367 MC56F8367E MC56F8167E 1.6 Data Sheet Conventions This data sheet uses the following conventions: OVERBAR This is used to indicate a signal that is active when pulled low. For example, the RESET pin is active when low. A high true (active high) signal is high or a low true (active low) signal is low. A high true (active high) signal is low or a low true (active low) signal is high. Signal/Symbol PIN PIN PIN PIN Logic State True False True False Signal State Asserted Deasserted Asserted Deasserted Voltage1 VIL/VOL VIH/VOH VIH/VOH VIL/VOL "asserted" "deasserted" Examples: 1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications. 56F8367 Technical Data, Rev. 3.0 14 Freescale Semiconductor Preliminary Introduction Part 2 Signal/Connection Descriptions 2.1 Introduction The input and output signals of the 56F8367 and 56F8167 are organized into functional groups, as detailed in Table 2-1 and as illustrated in Figure 2-1. In Table 2-2, each table row describes the signal or signals present on a pin. Table 2-1 Functional Group Pin Allocations Number of Pins in Package Functional Group 56F8367 Power (VDD or VDDA) Power Option Control Ground (VSS or VSSA) Supply Capacitors1 & VPP PLL and Clock Address Bus Data Bus Bus Control Interrupt and Program Control Pulse Width Modulator (PWM) Ports Serial Peripheral Interface (SPI) Port 0 Serial Peripheral Interface (SPI) Port 1 Quadrature Decoder Port 02 Quadrature Decoder Port 13 Serial Communications Interface (SCI) Ports2 CAN Ports Analog to Digital Converter (ADC) Ports Timer Module Ports JTAG/Enhanced On-Chip Emulation (EOnCE) Temperature Sense Dedicated GPIO 2. Alternately, can function as Quad Timer pins 3. Pins in this section can function as Quad Timer, SPI #1, or GPIO 56F8167 9 1 7 6 4 24 16 10 6 13 4 4 4 -- 4 -- 21 2 5 -- 7 9 1 7 6 4 24 16 10 6 26 4 -- 4 4 4 2 21 6 5 1 -- 1. If the on-chip regulator is disabled, the VCAP pins serve as 2.5V VDD_CORE power inputs 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 15 Power Power Power Ground Ground VDD_IO VDDA_OSC_PLL VDDA_ADC VSS VSSA_ADC OCR_DIS 7 1 1 6 1 1 4 2 1 1 1 1 6 2 8 8 1 1 1 1 7 9 1 1 1 1 1 1 1 PHASEA0 (TA0, GPIOC4) PHASEB0 (TA1, GPIOC5) INDEX0 (TA2, GPIOC6) HOME0 (TA3, GPIOC7) SCLK0 MOSI0 (GPIOE5) MISO0 (GPIOE6) SS0 (GPIOE7) PHASEA1(TB0, SCLK1, GPIOC0) PHASEB1 (TB1, MOSI1, GPIOC1) INDEX1 (TB2, MISO1, GPIOC2) HOME1 (TB3, SS1, GPIOC3) PWMA0 - 5 ISA0 - 2 (GPIOC8 - 10) FAULTA0 - 3 Quadrature Decoder 0 or Quad Timer A 56F8367 1 1 1 1 1 1 1 1 6 3 4 Other Supply Ports PLL and Clock *VCAP1 - VCAP4 VPP1 & VPP2 CLKMODE EXTAL XTAL CLKO A0 - A5 (GPIOA8 - 13) A6 - A7 (GPIOE2 - 3) A8 - A15 (GPIOA0 - 7) GPIOB0 - 7 (A16 - 23) GPIOB4 (A20, prescaler_clock) GPIOB5 (A21, SYS_CLK) GPIOB6 (A22, SYS_CLK2) GPIOB7 (A23, oscillator_clock) SPI0 or GPIO Quadrature Decoder 1 or Quad Timer B or SPI 1 or GPIO External Address Bus or GPIO PWMA 6 3 4 PWMB0 - 5 ISB0 - 2 (GPIOD10 - 12) FAULTB0 - 3 PWMB External Data Bus D0 - D6 (GPIOF9 - 15) D7 - D15 (GPIOF0 - 8) RD WR PS/CS0 (GPIODF8) 8 5 8 ANA0 - 7 VREF ANB0 - 7 ADCA ADCB External Bus Control 1 Temp_Sense Temperature Sense DS/CS1 (GPIOFD9) GPIOD0 (CS2, CAN2_TX) GPIOD1 (CS3, CAN2_RX) GPIOD2 - 5 (CS4 - 7) 1 1 1 4 1 1 1 1 1 1 1 1 1 2 4 1 1 CAN_RX CAN_TX FlexCAN SCI 0 or GPIO SCI 1 or GPIOD TXD0 (GPIOE0) RXD0 (GPIOE1) TXD1 (GPIOD6) RXD1 (GPIOD7) TCK TMS TDI TDO TRST TC0 - 1 (GPIOE8 - 9) TD0 - 3 (GPIOE10 - 13) Quad Timer C and D or GPIO 1 1 1 1 1 1 IRQA IRQB EXTBOOT EMI_MODE RESET RSTO INTERRUPT/ PROGRAM CONTROL JTAG/ EOnCE Port * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. Figure 2-1 56F8367 Signals Identified by Functional Group1 (160-pin LQFP) 1. Alternate pin functionality is shown in parenthesis; pin direction/type shown is the default functionality. 56F8367 Technical Data, Rev. 3.0 16 Freescale Semiconductor Preliminary Introduction Power Power Power Ground Ground VDD_IO VDDA_ADC VDDA_OSC_PLL VSS VSSA_ADC OCR_DIS 7 1 1 6 1 1 4 2 1 1 1 1 6 2 8 4 1 1 1 1 7 9 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 1 1 1 PHASEA0 (TA0, GPIOC4) PHASEB0 (TA1, GPIOC5) INDEX0 (TA2, GPIOC6) HOME0 (TA3, GPIOC7) Quadrature Decoder 0 or Quad Timer A or GPIO 56F8167 1 1 1 1 1 1 1 1 SCLK0 MOSI0 (GPIOE5) MISO0 (GPIOE6) SS0 (GPIOE7) (SCLK1, GPIOC0) (MOSI1, GPIOC1) (MISO1, GPIOC2) (SS1, GPIOC3) SPI0 or GPIO Other Supply Ports PLL and Clock *VCAP1 - VCAP4 VPP1 & VPP2 CLKMODE EXTAL XTAL CLKO A0 - A5 (GPIOA8 - 13) A6 - A7 (GPIOE2 - 3) A8 - A15 (GPIOA0 - 7) GPIOB0 - 3 (A16 - 19) GPIOB4 (A20, prescaler_clock) GPIOB5 (A21, SYS_CLK) GPIOB6 (A22, SYS_CLK2) GPIOB7 (A23, oscillator_clock) SPI 1 or GPIO External Address Bus or GPIO 3 (GPIOC8 - 10) GPIO 6 3 4 8 5 8 PWMB0 - 5 ISB0 - 2 (GPIOD10 - 12) FAULTB0 - 3 PWMB or GPIO External Data Bus or GPIO D0 - D6 (GPIOF9 - 15) D7 - D15 (GPIOF0 - 8) RD ANA0 - 7 VREF ANB0 - 7 ADCA ADCB External Bus Control or GPIO WR PS (CS0, GPIOD8) DS (CS1, GPIOD9) GPIOD0 - 5 (CS2 - 7) TXD0 (GPIOE0) RXD0 (GPIOE1) TXD1 (GPIOD6) RXD1 (GPIOD7) TCK TMS TDI TDO TRST SCI 0 or GPIO 2 4 TC0 - 1 (GPIOE8 - 9) (GPIOE10 - 13) QUAD TIMER C or GPIO SCI 1 or GPIO 1 1 1 1 1 1 IRQA IRQB EXTBOOT EMI_MODE RESET RSTO INTERRUPT / PROGRAM CONTROL JTAG/ EOnCE Port * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. Figure 2-2 56F8167 Signals Identified by Functional Group1 (160-pin LQFP) 1. Alternate pin functionality is shown in parenthesis; pin direction/type shown is the default functionality. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 17 2.2 Signal Pins After reset, each pin is configured for its primary function (listed first). Any alternate functionality must be programmed. Note: Signals in italics are NOT available in the 56F8167 device. Note: The 160 Map Ball Grid Array is not available in the 56F8167 device. If the "State During Reset" lists more than one state for a pin, the first state is the actual reset state. Other states show the reset condition of the alternate function, which you get if the alternate pin function is selected without changing the configuration of the alternate peripheral. For example, the A8/GPIOA0 pin shows that it is tri-stated during reset. If the GPIOA_PER is changed to select the GPIO function of the pin, it will become an input if no other registers are changed. Note: LQFP Pin numbers and MBGA Ball numbers do not always correlate in Table 2-2. Please contact factory for exact correlation. Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO VDDA_ADC VDDA_OSC_ PLL Pin No. 1,16 31,42 77,96 134 Ball No. Type State During Reset Signal Description F4,K5 E5,K7 E9,K10 F11 Supply I/O Power -- This pin supplies 3.3V power to the chip I/O interface and also the Processor core throught the on-chip voltage regulator, if it is enabled. 114 C14 Supply ADC Power -- This pin supplies 3.3V power to the ADC modules. It must be connected to a clean analog power supply. Oscillator and PLL Power -- This pin supplies 3.3V power to the OSC and to the internal regulator that in turn supplies the Phase Locked Loop. It must be connected to a clean analog power supply. VSS -- These pins provide ground for chip logic and I/O drivers. 92 K13 Supply VSS VSS VSS VSS VSS VSS 27,41 74,80 125 160 J4,K11 G11,E7 J11,E6 Supply 56F8367 Technical Data, Rev. 3.0 18 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name VSSA_ADC OCR_DIS Pin No. 115 Ball No. Type State During Reset Signal Description D12 Supply ADC Analog Ground -- This pin supplies an analog ground to the ADC modules. Input On-Chip Regulator Disable -- Tie this pin to VSS to enable the on-chip regulator Tie this pin to VDD to disable the on-chip regulator This pin is intended to be a static DC signal from power-up to shut down. Do not try to toggle this pin for power savings during operation. 91 K14 Input VCAP1* VCAP2* VCAP3* VCAP4* 62 144 95 15 K8 E8 H11 G4 Supply Supply VCAP1 - 4 -- When OCR_DIS is tied to VSS (regulator enabled), connect each pin to a 2.2F or greater bypass capacitor in order to bypass the core logic voltage regulator, required for proper chip operation. When OCR_DIS is tied to VDD (regulator disabled), these pins become VDD_CORE and should be connected to a regulated 2.5V power supply. Note: This bypass is required even if the chip is powered with an external supply. * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. VPP1 VPP2 CLKMODE 141 2 99 A7 C2 H12 Input Input Clock Input Mode Selection -- This input determines the function of the XTAL and EXTAL pins. 1 = External clock input on XTAL is used to directly drive the input clock of the chip. The EXTAL pin should be grounded. 0 = A crystal or ceramic resonator should be connected between XTAL and EXTAL. EXTAL 94 J12 Input Input External Crystal Oscillator Input -- This input can be connected to an 8MHz external crystal. Tie this pin low if XTAL is driven by an external clock source. Input Input VPP1 - 2 -- These pins should be left unconnected as an open circuit for normal functionality. XTAL 93 K12 Input/ Output Chip-drive Crystal Oscillator Output -- This output connects the internal crystal n oscillator output to an external crystal. If an external clock is used, XTAL must be used as the input and EXTAL connected to GND. The input clock can be selected to provide the clock directly to the core. This input clock can also be selected as the input clock for the on-chip PLL. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 19 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name CLKO Pin No. 3 Ball No. Type State During Reset Signal Description D3 Output Tri-Stated Clock Output -- This pin outputs a buffered clock signal. Using the SIM CLKO Select Register (SIM_CLKOSR), this pin can be programmed as any of the following: disabled, CLK_MSTR (system clock), IPBus clock, oscillator output, prescaler clock and postscaler clock. Other signals are also available for test purposes. See Part 6.5.7 for details. A0 154 C3 Output Tri-stated Address Bus -- A0 - A5 specify six of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A0 - A5 and EMI control signals are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (GPIOA8) A1 (GPIOA9) A2 (GPIOA10) A3 (GPIOA11) A4 (GPIOA12) A5 (GPIOA13) A6 10 E3 Input/ Output Input Port A GPIO -- These six GPIO pins can be individually programmed as input or output pins. After reset, the default state is Address Bus. 11 E4 To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOA_PUR register. Example: GPIOA8, clear bit 8 in the GPIOA_PUR register. 12 F2 13 F1 14 F3 17 G1 Output Tri-stated Address Bus -- A6 - A7 specify two of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A6 - A7 and EMI control signals are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (GPIOE2) A7 (GPIOE3) 18 G3 Schmitt Input/ Output Input Port E GPIO -- These two GPIO pins can be individually programmed as input or output pins. After reset, the default state is Address Bus. To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOE_PUR register. Example: GPIOE2, clear bit 2 in the GPIOE_PUR register. 56F8367 Technical Data, Rev. 3.0 20 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name A8 Pin No. 19 Ball No. Type State During Reset Signal Description G2 Output Tri-stated Address Bus-- A8 - A15 specify eight of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A8 - A15 and EMI control signals are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (GPIOA0) A9 (GPIOA1) A10 (GPIOA2) A11 (GPIOA3) A12 (GPIOA4) A13 (GPIOA5) A14 (GPIOA6) A15 (GPIOA7) 20 H1 Schmitt Input/ Output Input Port A GPIO -- These eight GPIO pins can be individually programmed as input or output pins. After reset, the default state is Address Bus. 21 H2 To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOA_PUR register. Example: GPIOA0, clear bit 0 in the GPIOA_PUR register. 22 H4 23 H3 24 J1 25 J2 26 J3 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 21 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name GPIOB0 Pin No. 33 Ball No. Type State During Reset Input Signal Description L1 Schmitt Input/ Output Output Port B GPIO -- These four GPIO pins can be programmed as input or output pins. (A16) GPIOB1 (A17) GPIOB2 (A18) GPIOB3 (A19) 34 L3 Tri-stated Address Bus -- A16 - A19 specify one of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A16 - A19 and EMI control signals are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. After reset, the startup state of GPIOB0 - GPIOB3 (GPIO or address) is determined as a function of EXTBOOT, EMI_MODE and the Flash security setting. See Table 4-4 for further information on when this pin is configured as an address pin at reset. In all cases, this state may be changed by writing to GPIOB_PER. To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOB_PUR register. 35 L2 36 M1 GPIOB4 37 M2 Schmitt Input/ Output Output Input Port B GPIO -- These four GPIO pins can be programmed as input or output pins. (A20) Tri-stated Address Bus -- A20 - A23 specify one of the address lines for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), A20-A23 and EMI control signals are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (prescaler_ clock) GPIOB5 (A21) (SYS_CLK) GPIOB6 (A22) (SYS_CLK2 ) GPIOB7 (A23) (oscillator_ clock) 46 N4 Output Output Clock Outputs -- can be used to monitor the prescaler_clock, SYS_CLK, SYS_CLK2 or oscillator_clock on GPIOB4 through GPIOB7, respectively. After reset, the default state is GPIO. 47 P3 These pins can also be used to extend the external address bus to its full length or to view any of several system clocks. In these cases, the GPIO_B_PER can be used to individually disable the GPIO. The CLKOSR register in the SIM ( see Part 6.5.7) can then be used to choose between address and clock functions. 48 M4 56F8367 Technical Data, Rev. 3.0 22 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name D0 Pin No. 70 Ball No. Type State During Reset Signal Description P10 Input/ Output Tri-stated Data Bus -- D0 - D6 specify part of the data for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), D0-D6 are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (GPIOF9) D1 (GPIOF10) D2 (GPIOF11) D3 (GPIOF12) D4 (GPIOF13) D5 (GPIOF14) D6 (GPIOF15) 71 N10 Input/ Output Input Port F GPIO -- These seven GPIO pins can be individually programmed as input or output pins. After reset, these pins default to the EMI Data Bus function. 83 P14 To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOF_PUR register. Example: GPIOF9, clear bit 9 in the GPIOF_PUR register. 86 L13 88 L14 89 L12 90 L11 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 23 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name D7 Pin No. 28 Ball No. Type State During Reset Signal Description K1 Input/ Output Tri-stated Data Bus -- D7 - D15 specify part of the data for external program or data memory accesses. Depending upon the state of the DRV bit in the EMI bus control register (BCR), D7 - D15 are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (GPIOF0) D8 (GPIOF1) D9 (GPIOF2) D10 (GPIOF3) D11 (GPIOF4) D12 (GPIOF5) D13 (GPIOF6) D14 (GPIOF7) D15 (GPIOF8) RD 29 K3 Input/ Output Input Port F GPIO -- These nine GPIO pins can be individually programmed as input or output pins. At reset, these pins default to Data Bus functionality. 30 K2 To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOF_PUR register. Example: GPIOF0, clear bit 0 in the GPIOF_PUR register. 32 K4 149 A5 150 A4 151 B5 152 C4 153 A3 52 P5 Output Tri-stated Read Enable -- RD is asserted during external memory read cycles. When RD is asserted low, pins D0 - D15 become inputs and an external device is enabled onto the data bus. When RD is deasserted high, the external data is latched inside the device. When RD is asserted, it qualifies the A0 - A23, PS, DS, and CSn pins. RD can be connected directly to the OE pin of a static RAM or ROM. Depending upon the state of the DRV bit in the EMI bus control register (BCR), RD is tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. To deactivate the internal pull-up resistor, set the CTRL bit in the SIM_PUDR register. 56F8367 Technical Data, Rev. 3.0 24 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name WR Pin No. 51 Ball No. Type State During Reset Signal Description L4 Output Tri-stated Write Enable -- WR is asserted during external memory write cycles. When WR is asserted low, pins D0 - D15 become outputs and the device puts data on the bus. When WR is deasserted high, the external data is latched inside the external device. When WR is asserted, it qualifies the A0 - A23, PS, DS, and CSn pins. WR can be connected directly to the WE pin of a static RAM. Depending upon the state of the DRV bit in the EMI bus control register (BCR), WR is tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. To deactivate the internal pull-up resistor, set the CTRL bit in the SIM_PUDR register. PS (CS0) 53 N6 Output Tri-stated Program Memory Select -- This signal is actually CS0 in the EMI, which is programmed at reset for compatibility with the 56F80x PS signal. PS is asserted low for external program memory access. Depending upon the state of the DRV bit in the EMI bus control register (BCR), CS0 is tri-stated when the external bus is inactive. CS0 resets to provide the PS function as defined on the 56F80x devices. (GPIOD8) Input/ Output Input Port D GPIO -- This GPIO pin can be individually programmed as an input or output pin. To deactivate the internal pull-up resistor, clear bit 8 in the GPIOD_PUR register. DS (CS1) 54 L5 Outpu Tri-stated Data Memory Select -- This signal is actually CS1 in the EMI, which is programmed at reset for compatibility with the 56F80x DS signal. DS is asserted low for external data memory access. Depending upon the state of the DRV bit in the EMI bus control register (BCR), CS1 is tri-stated when the external bus is inactive. CS1 resets to provide the DS function as defined on the 56F80x devices. (GPIOD9) Input/ Outputt Input Port D GPIO -- This GPIO pin can be individually programmed as an input or output pin. To deactivate the internal pull-up resistor, clear bit 9 in the GPIOD_PUR register. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 25 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name GPIOD0 Pin No. 55 Ball No. Type State During Reset Input Signal Description P6 Input/ Output Output Port D GPIO -- This GPIO pin can be individually programmed as an input or output pin. (CS2) Tri-stated Chip Select -- CS2 may be programmed within the EMI module to act as a chip select for specific areas of the external memory map. Depending upon the state of the DRV bit in the EMI Bus Control Register (BCR), CS2 is tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (CAN2_TX) Open Drain Output Output FlexCAN2 Transmit Data -- CAN output. At reset, this pin is configured as GPIO. This configuration can be changed by setting bit 0 in the GPIO_D_PER register. Then change bit 4 in the SIM_GPS register to select the desired peripheral function. To deactivate the internal pull-up resistor, clear bit 0 in the GPIOD_PUR register. GPIOD1 56 L6 Schmitt Input/ Output Output Input Port D GPIO -- This GPIO pin can be individually programmed as an input or output pin. (CS3) Tri-stated Chip Select -- CS3 may be programmed within the EMI module to act as a chip select for specific areas of the external memory map. Depending upon the state of the DRV bit in the EMI Bus Control Register (BCR), CS3 is tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. (CAN2_RX) Schmitt Input Input FlexCAN2 Receive Data -- This is the CAN input. This pin has an internal pull-up resistor. At reset, this pin is configured as GPIO. This configuration can be changed by setting bit 1 in the GPIO_D_PER register. Then change bit 5 in the SIM_GPS register to select the desired peripheral function. To deactivate the internal pull-up resistor, clear bit 1 in the GPIOD_PUR register. 56F8367 Technical Data, Rev. 3.0 26 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name GPIOD2 Pin No. 57 Ball No. Type State During Reset Input Signal Description K6 Input/ Output Output Port D GPIO -- These four GPIO pins can be individually programmed as input or output pins. (CS4) GPIOD3 (CS5) GPIOD4 (CS6) GPIOD5 (CS7) 58 N7 Tri-stated Chip Select -- CS4 - CS7 may be programmed within the EMI module to act as chip selects for specific areas of the external memory map. Depending upon the state of the DRV bit in the EMI bus control register (BCR), CS4 - CS7 are tri-stated when the external bus is inactive. Most designs will want to change the DRV state to DRV = 1 instead of using the default setting. At reset, these pins are configured as GPIO. To deactivate the internal pull-up resistor, clear the appropriate GPIO bit in the GPIOD_PUR register. Example: GPIOD2, clear bit 2 in the GPIOD_PUR register. 59 P7 60 L7 TXD0 (GPIOE0) 4 B1 Output Input/ Output Tri-stated Transmit Data -- SCI0 transmit data output Input Port E GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI output. To deactivate the internal pull-up resistor, clear bit 0 in the GPIOE_PUR register. RXD0 (GPIOE1) 5 D2 Input Input/ Output Input Input Receive Data -- SCI0 receive data input Port E GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI output. To deactivate the internal pull-up resistor, clear bit 1 in the GPIOE_PUR register. TXD1 (GPIOD6) 49 P4 Output Input/ Output Tri-stated Transmit Data -- SCI1 transmit data output Input Port D GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI output. To deactivate the internal pull-up resistor, clear bit 6 in the GPIOD_PUR register. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 27 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name RXD1 (GPIOD7) Pin No. 50 Ball No. Type State During Reset Input Input Signal Description N5 Input Input/ Output Receive Data -- SCI1 receive data input Port D GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCI input. To deactivate the internal pull-up resistor, clear bit 7 in the GPIOD_PUR register. TCK 137 D8 Schmitt Input Input, Test Clock Input -- This input pin provides a gated clock to pulled low synchronize the test logic and shift serial data to the JTAG/EOnCE internally port. The pin is connected internally to a pull-down resistor. Input, pulled high internally Test Mode Select Input -- This input pin is used to sequence the JTAG TAP controller's state machine. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. To deactivate the internal pull-up resistor, set the JTAG bit in the SIM_PUDR register. TMS 138 A8 Schmitt Input TDI 139 B8 Schmitt Input Input, pulled high internally Test Data Input -- This input pin provides a serial input data stream to the JTAG/EOnCE port. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. To deactivate the internal pull-up resistor, set the JTAG bit in the SIM_PUDR register. TDO 140 D7 Output Tri-stated Test Data Output -- This tri-stateable output pin provides a serial output data stream from the JTAG/EOnCE port. It is driven in the shift-IR and shift-DR controller states, and changes on the falling edge of TCK. Input, pulled high internally Test Reset -- As an input, a low signal on this pin provides a reset signal to the JTAG TAP controller. To ensure complete hardware reset, TRST should be asserted whenever RESET is asserted. The only exception occurs in a debugging environment when a hardware device reset is required and the JTAG/EOnCE module must not be reset. In this case, assert RESET, but do not assert TRST. To deactivate the internal pull-up resistor, set the JTAG bit in the SIM_PUDR register. TRST 136 D9 Schmitt Input 56F8367 Technical Data, Rev. 3.0 28 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name PHASEA0 Pin No. 155 Ball No. Type State During Reset Input Signal Description A2 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Phase A -- Quadrature Decoder 0, PHASEA input (TA0) Input TA0 -- Timer A, Channel 0 (GPIOC4) Input Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is PHASEA0. To deactivate the internal pull-up resistor, clear bit 4 of the GPIOC_PUR register. PHASEB0 156 B4 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input Phase B -- Quadrature Decoder 0, PHASEB input (TA1) Input TA1 -- Timer A, Channel (GPIOC5) Input Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is PHASEB0. To deactivate the internal pull-up resistor, clear bit 5 of the GPIOC_PUR register. INDEX0 157 A1 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input Index -- Quadrature Decoder 0, INDEX input (TA2) Input TA2 -- Timer A, Channel 2 (GPOPC6) Input Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is INDEX0. To deactivate the internal pull-up resistor, clear bit 6 of the GPIOC_PUR register. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 29 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name HOME0 Pin No. 158 Ball No. Type State During Reset Input Signal Description B3 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Home -- Quadrature Decoder 0, HOME input (TA3) Input TA3 -- Timer A, Channel 3 (GPIOC7) Input Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is HOME0. To deactivate the internal pull-up resistor, clear bit 7 of the GPIOC_PUR register. SCLK0 146 A6 Schmitt Input/ Output Schmitt Input/ Output Input SPI 0 Serial Clock -- In the master mode, this pin serves as an output, clocking slaved listeners. In slave mode, this pin serves as the data clock input. Port E GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is SCLK0. To deactivate the internal pull-up resistor, clear bit 4 in the GPIOE_PUR register. (GPIOE4) Input MOSI0 148 D4 Input/ Output Tri-stated SPI 0 Master Out/Slave In -- This serial data pin is an output from a master device and an input to a slave device. The master device places data on the MOSI line a half-cycle before the clock edge the slave device uses to latch the data. Input Port E GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is MOSI0. To deactivate the internal pull-up resistor, clear bit 5 in the GPIOE_PUR register. (GPIOE5) Input/ Output 56F8367 Technical Data, Rev. 3.0 30 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name MISO0 Pin No. 147 Ball No. Type State During Reset Input Signal Description B6 Input/ Output SPI 0 Master In/Slave Out -- This serial data pin is an input to a master device and an output from a slave device. The MISO line of a slave device is placed in the high-impedance state if the slave device is not selected. The slave device places data on the MISO line a half-cycle before the clock edge the master device uses to latch the data. Port E GPIO -- This GPIO pin can be individually programmed as an input or output pin. After reset, the default state is MISO0. To deactivate the internal pull-up resistor, clear bit 6 in the GPIOE_PUR register. (GPIOE6) Input/ Output Input SS0 145 D5 Input Input SPI 0 Slave Select -- SS0 is used in slave mode to indicate to the SPI module that the current transfer is to be received. Port E GPIO -- This GPIO pin can be individually programmed as input or output pin. After reset, the default state is SS0. To deactivate the internal pull-up resistor, clear bit 7 in the GPIOE_PUR register. (GPIOE7) Input/ Output Input PHASEA1 6 C1 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input Phase A1 -- Quadrature Decoder 1, PHASEA input for decoder 1. (TB0) Input TB0 -- Timer B, Channel 0 (SCLK1) Input SPI 1 Serial Clock -- In the master mode, this pin serves as an output, clocking slaved listeners. In slave mode, this pin serves as the data clock input. To activate the SPI function, set the PHSA_ALT bit in the SIM_GPS register. For details, see Part 6.5.8. Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. In the 56F8367, the default state after reset is PHASEA1. In the 56F8167, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 0 in the GPIOC_PUR register. (GPIOC0) Schmitt Input/ Output Input 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 31 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name PHASEB1 Pin No. 7 Ball No. Type State During Reset Input Signal Description D1 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Phase B1 -- Quadrature Decoder 1, PHASEB input for decoder 1. (TB1) Input TB1 -- Timer B, Channel 1 (MOSI1) Tri-stated SPI 1 Master Out/Slave In -- This serial data pin is an output from a master device and an input to a slave device. The master device places data on the MOSI line a half-cycle before the clock edge the slave device uses to latch the data. To activate the SPI function, set the PHSB_ALT bit in the SIM_GPS register. For details, see Part 6.5.8. Input Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. In the 56F8367, the default state after reset is PHASEB1. In the 56F8167, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 1 in the GPIOC_PUR register. (GPIOC1) Schmitt Input/ Output INDEX1 8 E2 Schmitt Input Schmitt Input/ Output Schmitt Input/ Output Input Index1 -- Quadrature Decoder 1, INDEX input (TB2) Input TB2 -- Timer B, Channel 2 (MISO1) Input SPI 1 Master In/Slave Out -- This serial data pin is an input to a master device and an output from a slave device. The MISO line of a slave device is placed in the high-impedance state if the slave device is not selected. The slave device places data on the MISO line a half-cycle before the clock edge the master device uses to latch the data. To activate the SPI function, set the INDEX_ALT bit in the SIM_GPS register. For details, see Part 6.5.8. Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. In the 56F8367, the default state after reset is INDEX1. In the 56F8167, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 2 in the GPIOC_PUR register. (GPIOC2) Schmitt Input/ Output Input 56F8367 Technical Data, Rev. 3.0 32 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name HOME1 Pin No. 9 Ball No. Type State During Reset Input Signal Description E1 Schmitt Input Schmitt Input/ Output Schmitt Input Home -- Quadrature Decoder 1, HOME input (TB3) Input TB3 -- Timer B, Channel 3 (SS1) Input SPI 1 Slave Select -- In the master mode, this pin is used to arbitrate multiple masters. In slave mode, this pin is used to select the slave. To activate the SPI function, set the HOME_ALT bit in the SIM_GPS register. For details, see Part 6.5.8. Port C GPIO -- This GPIO pin can be individually programmed as an input or output pin. In the 56F8367, the default state after reset is HOME1. In the 56F8167, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear bit 3 in the GPIOC_PUR register. (GPIOC3) Schmitt Input/ Output Input PWMA0 PWMA1 PWMA2 PWMA3 PWMA4 PWMA5 ISA0 73 75 76 78 79 81 126 M11 P12 N11 M12 P13 N12 A11 Output Tri-State PWMA0 - 5 -- These are six PWMA outputs. Schmitt Input Input ISA0 - 2 -- These three input current status pins are used for top/bottom pulse width correction in complementary channel operation for PWMA. Port C GPIO -- These GPIO pins can be individually programmed as input or output pins. In the 56F8367, these pins default to ISA functionality after reset. (GPIOC8) ISA1 (GPIOC9) ISA2 (GPIOC10) 127 C11 Schmitt Input/ Output Input 128 D11 In the 56F8167, the default state is not one of the functions offered and must be reconfigured. To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOC_PUR register. For details, see Part 6.5.8. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 33 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name FAULTA0 FAULTA1 FAULTA2 Pin No. 82 84 85 Ball No. Type State During Reset Input Signal Description N13 N14 M13 Schmitt Input FAULTA0 - 2 -- These three fault input pins are used for disabling selected PWMA outputs in cases where fault conditions originate off-chip. To deactivate the internal pull-up resistor, set the PWMA0 bit in the SIM_PUDR register. For details, see Part 6.5.8. FAULTA3 87 M14 Schmitt Input Input FAULTA3 -- This fault input pin is used for disabling selected PWMA outputs in cases where fault conditions originate off-chip. To deactivate the internal pull-up resistor, set the PWMA1 bit in the SIM_PUDR register. See Part 6.5.6 for details. PWMB0 PWMB1 PWMB2 PWMB3 PWMB4 PWMB5 ISB0 38 39 40 43 44 45 61 N1 P1 N2 N3 P2 M3 N8 Output Tri-State PWMB0 - 5 -- Six PWMB output pins. Schmitt Input Input ISB0 - 2 -- These three input current status pins are used for top/bottom pulse width correction in complementary channel operation for PWMB. Port D GPIO -- These GPIO pins can be individually programmed as input or output pins. At reset, these pins default to ISB functionality. (GPIOD10) ISB1 (GPIOD11) ISB2 (GPIOD12) FAULTB0 FAULTB1 FAULTB2 FAULTB3 ANA0 ANA1 ANA2 ANA3 63 L8 Schmitt Input/ Output Input 64 P8 To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOD_PUR register. For details, see Part 6.5.8. Schmitt Input Input FAULTB0 - 3 -- These four fault input pins are used for disabling selected PWMB outputs in cases where fault conditions originate off-chip. To deactivate the internal pull-up resistor, set the PWMB bit in the SIM_PUDR register. For details, see Part 6.5.8. Input Input ANA0 - 3 -- Analog inputs to ADC A, channel 0 67 68 69 72 100 101 102 103 N9 L9 L10 P11 G13 H13 G12 F13 56F8367 Technical Data, Rev. 3.0 34 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name ANA4 ANA5 ANA6 ANA7 VREFH Pin No. 104 105 106 107 113 Ball No. Type State During Reset Input Signal Description F12 H14 G14 E13 D14 Input ANA4 - 7 -- Analog inputs to ADC A, channel 1 Input Input VREFH -- Analog Reference Voltage High. VREFH must be less than or equal to VDDA_ADC. VREFP, VREFMID & VREFN -- Internal pins for voltage reference which are brought off-chip so they can be bypassed. Connect to a 0.1F low ESR capacitor. VREFP VREFMID VREFN VREFLO 112 111 110 109 D13 E14 F14 E12 Input/ Output Input/ Output Input Input VREFLO -- Analog Reference Voltage Low. This should normally be connected to a low-noise VSS. ANB0 - 3 -- Analog inputs to ADC B, channel 0 ANB0 ANB1 ANB2 ANB3 ANB4 ANB5 ANB6 ANB7 TEMP_SEN SE 116 117 118 119 120 121 122 123 108 C13 B14 C12 B13 A14 A13 B12 A12 E11 Input Input Input Input ANB4 - 7 -- Analog inputs to ADC B, channel 1 Output Output Temperature Sense Diode -- This signal connects to an on-chip diode that can be connected to one of the ADC inputs and used to monitor the temperature of the die. Must be bypassed with a 0.01F capacitor. FlexCAN Receive Data -- This is the CAN input. This pin has an internal pull-up resistor. To deactivate the internal pull-up resistor, set the CAN bit in the SIM_PUDR register. CAN_RX 143 B7 Schmitt Input Input CAN_TX 142 D6 Open Drain Output Open Drain Output FlexCAN Transmit Data -- CAN output 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 35 Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name TC0 Pin No. 133 Ball No. Type State During Reset Input Signal Description A9 Schmitt Input/ Output Schmitt Input/ Output TC0 -- Timer C, Channel 0 and 1 (GPIOE8) TC1 (GPIOE9) 135 B9 Input Port E GPIO -- These GPIO pins can be individually programmed as input or output pins. At reset, these pins default to Timer functionality. To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOE_PUR register. TD0 129 B10 Schmitt Input/ Output Schmitt Input/ Output Input TD0 - 3-- Timer D, Channels 0, 1, 2 and 3 (GPIOE10) TD1 (GPIOE11) TD2 (GPIOE12) TD3 (GPIOE13) IRQA IRQB 130 A10 Input Port E GPIO -- These GPIO pins can be individually programmed as input or output pins. At reset, these pins default to Timer functionality. 131 D10 To deactivate the internal pull-up resistor, clear the appropriate bit of the GPIOE_PUR register. See Part 6.5.6 for details. 132 E10 65 66 K9 P9 Schmitt Input Input External Interrupt Request A and B -- The IRQA and IRQB inputs are asynchronous external interrupt requests during Stop and Wait mode operation. During other operating modes, they are synchronized external interrupt requests, which indicate an external device is requesting service. They can be programmed to be level-sensitive or negative-edge triggered. To deactivate the internal pull-up resistor, set the IRQ bit in the SIM_PUDR register. See Part 6.5.6 for details. 56F8367 Technical Data, Rev. 3.0 36 Freescale Semiconductor Preliminary Signal Pins Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA Signal Name RESET Pin No. 98 Ball No. Type State During Reset Input Signal Description J14 Schmitt Input Reset -- This input is a direct hardware reset on the processor. When RESET is asserted low, the device is initialized and placed in the reset state. A Schmitt trigger input is used for noise immunity. When the RESET pin is deasserted, the initial chip operating mode is latched from the EXTBOOT pin. The internal reset signal will be deasserted synchronous with the internal clocks after a fixed number of internal clocks. To ensure complete hardware reset, RESET and TRST should be asserted together. The only exception occurs in a debugging environment when a hardware device reset is required and the JTAG/EOnCE module must not be reset. In this case, assert RESET but do not assert TRST. Note: The internal Power-On Reset will assert on initial power-up. To deactivate the internal pull-up resistor, set the RESET bit in the SIM_PUDR register. See Part 6.5.6 for details. RSTO 97 J13 Output Output Reset Output -- This output reflects the internal reset state of the chip. External Boot -- This input is tied to VDD to force the device to boot from off-chip memory (assuming that the on-chip Flash memory is not in a secure state). Otherwise, it is tied to ground. For details, see Table 4-4. Note: When this pin is tied low, the customer boot software should disable the internal pull-up resistor by setting the XBOOT bit of the SIM_PUDR; see Part 6.5.6. EXTBOOT 124 B11 Schmitt Input Input EMI_MODE 159 B2 Schmitt Input Input External Memory Mode -- This input is tied to VDD in order to enable an extra four address lines, for a total of 20 address lines out of reset. This function is also affected by EXTBOOT and the Flash security mode. For details, see Table 4-4. If a 20-bit address bus is not desired, then this pin is tied to ground. Note: When this pin is tied low, the customer boot software should disable the internal pull-up resistor by setting the EMI_MODE bit of the SIM_PUDR; see Part 6.5.6. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 37 Part 3 On-Chip Clock Synthesis (OCCS) 3.1 Introduction Refer to the OCCS chapter of the 56F8300 Peripheral User Manual for a full description of the OCCS. The material contained here identifies the specific features of the OCCS design. Figure 3-1 shows the specific OCCS block diagram to reference in the OCCS chapter of the 56F8300 Peripheral User Manual. CLKMODE XTAL MUX Crystal OSC EXTAL ZSRC Prescaler CLK PLLCID FREF PLLDB PLL FOUT x (1 to 128) FEEDBACK PLLCOD / (1,2,4,8) MSTR_OSC Prescaler /2 FOUT/2 Postscaler / (1,2,4,8) Postscaler CLK MUX SYS_CLK2 Source to SIM Bus Interface & Control Bus Interface Lock Detector Loss of Reference Clock Detector LCK Loss of Reference Clock Interrupt Figure 3-1 OCCS Block Diagram 3.2 External Clock Operation The system clock can be derived from an external crystal, ceramic resonator, or an external system clock signal. To generate a reference frequency using the internal oscillator, a reference crystal or ceramic resonator must be connected between the EXTAL and XTAL pins. 3.2.1 Crystal Oscillator The internal oscillator is also designed to interface with a parallel-resonant crystal resonator in the frequency range specified for the external crystal in Table 10-13. A recommended crystal oscillator circuit is shown in Figure 3-2. Follow the crystal supplier's recommendations when selecting a crystal, since crystal parameters determine the component values required to provide maximum stability and reliable start-up. The crystal and associated components should be mounted as near as possible to the EXTAL and XTAL pins to minimize output distortion and start-up stabilization time. 56F8367 Technical Data, Rev. 3.0 38 Freescale Semiconductor Preliminary External Clock Operation Crystal Frequency = 4 - 8MHz (optimized for 8MHz) EXTAL XTAL RZ CLKMODE = 0 EXTAL XTAL RZ Sample External Crystal Parameters: Rz = 750 K Note: If the operating temperature range is limited to below 85oC (105oC junction), then Rz = 10 Meg CL1 CL2 Figure 3-2 Connecting to a Crystal Oscillator Note: The OCCS_COHL bit must be set to 1 when a crystal oscillator is used. The reset condition on the OCCS_COHL bit is 0. Please see the COHL bit in the Oscillator Control (OSCTL) register, discussed in the 56F8300 Peripheral User Manual. 3.2.2 Ceramic Resonator (Default) It is also possible to drive the internal oscillator with a ceramic resonator, assuming the overall system design can tolerate the reduced signal integrity. A typical ceramic resonator circuit is shown in Figure 3-3. Refer to the supplier's recommendations when selecting a ceramic resonator and associated components. The resonator and components should be mounted as near as possible to the EXTAL and XTAL pins. 2 Terminal EXTAL XTAL RZ Resonator Frequency = 4 - 8MHz (optimized for 8MHz) 3 Terminal EXTAL XTAL RZ Sample External Ceramic Resonator Parameters: Rz = 750 K CL1 CL2 C1 C2 CLKMODE = 0 Figure 3-3 Connecting a Ceramic Resonator Note: The OCCS_COHL bit must be set to 0 when a ceramic resonator is used. The reset condition on the OCCS_COHL bit is 0. Please see the COHL bit in the Oscillator Control (OSCTL) register, discussed in the 56F8300 Peripheral User Manual. 3.2.3 External Clock Source The recommended method of connecting an external clock is given in Figure 3-4. The external clock source is connected to XTAL and the EXTAL pin is grounded. When using an external clock source, set the OCCS_COHL bit high as well. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 39 XTAL External Clock EXTAL VSS Note: When using an external clocking source with this configuration, the input "CLKMODE" should be high and the COHL bit in the OSCTL register should be set to 1. Figure 3-4 Connecting an External Clock Register 3.3 Registers When referring to the register definitions for the OCCS in the 56F8300 Peripheral User Manual, use the register definitions without the internal Relaxation Oscillator, since the 56F8367/56F8167 do NOT contain this oscillator. Part 4 Memory Operating Modes (MEM) 4.1 Introduction The 56F8367 and 56F8167 devices are 16-bit motor-control chips based on the 56800E core. These parts use a Harvard-style architecture with two independent memory spaces for Data and Program. On-chip RAM and Flash memory are used in both spaces. This chapter provides memory maps for: * * Program Address Space including the Interrupt Vector Table Data Address Space including the EOnCE Memory and Peripheral Memory Maps On-chip memory sizes for each device are summarized in Table 4-1. Flash memories' restrictions are identified in the "Use Restrictions" column of Table 4-1. Note: Data Flash and Program RAM are NOT available on the 56F8167 device. Table 4-1 Chip Memory Configurations On-Chip Memory Program Flash Data Flash 56F8367 512KB 32KB 56F8167 512KB -- Use Restrictions Erase/Program via Flash interface unit and word writes to CDBW Erase/Program via Flash interface unit and word writes to CDBW. Data Flash can be read via one of CDBR or XDB2, but not both simultaneously None None Erase/Program via Flash Interface unit and word to CDWB Program RAM Data RAM Program Boot Flash 4KB 32KB 32KB -- 32KB 32KB 56F8367 Technical Data, Rev. 3.0 40 Freescale Semiconductor Preliminary Program Map 4.2 Program Map The operating mode control bits (MA and MB) in the Operating Mode Register (OMR) control the Program memory map. At reset, these bits are set as indicated in Table 4-2. Table 4-4 shows the memory map configurations that are possible at reset. After reset, the OMR MA bit can be changed and will have an effect on the P-space memory map, as shown in Table 4-3. Changing the OMR MB bit will have no effect. Table 4-2 OMR MB/MA Value at Reset OMR MB = Flash Secured State1, 2 0 0 1 1 OMR MA = EXTBOOT Pin 0 1 0 1 Chip Operating Mode Mode 0 - Internal Boot; EMI is configured to use 16 address lines; Flash Memory is secured; external P-space is not allowed; the EOnCE is disabled Not valid; cannot boot externally if the Flash is secured and will actually configure to 00 state Mode 0 - Internal Boot; EMI is configured to use 16 address lines Mode 1 - External Boot; Flash Memory is not secured; EMI configuration is determined by the state of the EMI_MODE pin 1. This bit is only configured at reset. If the Flash secured state changes, this will not be reflected in MB until the next reset. 2. Changing MB in software will not affect Flash memory security. Table 4-3 Changing OMR MA Value During Normal Operation OMR MA 0 1 Chip Operating Mode Use internal P-space memory map configuration Use external P-space memory map configuration - If MB = 0 at reset, changing this bit has no effect. The device's external memory interface (EMI) can operate much like the 56F80x family's EMI, or it can be operated in a mode similar to that used on other products in the 56800E family. Initially, CS0 and CS1 are configured as PS and DS, in a mode compatible with earlier 56800 devices. Eighteen address lines are required to shadow the first 192K of internal program space when booting externally for development purposes. Therefore, the entire complement of on-chip memory cannot be accessed using a 16-bit 56800-compatible address bus. To address this situation, the EMI_MODE pin can be used to configure four GPIO pins as Address[19:16] upon reset (Software reconfiguration of the highest address lines [A20-23] is required if the full address range is to be used.) The EMI_MODE bit also affects the reset vector address, as provided in Table 4-4. Additional pins must be configured as address or chip select signals to access addresses at P: $10 0000 and above. Note: Program RAM is NOT available on the 56F8167 device. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 41 Table 4-4 Program Memory Map at Reset Mode 0 (MA = 0) Begin/End Address Internal Boot Internal Boot 16-Bit External Address Bus P:$1F FFFF P:$10 0000 P:$0F FFFF P:$05 0000 P:$04 FFFF P:$04 F800 P:$04 F7FF P:$04 4000 P:$04 3FFF P:$04 0000 Mode 11 (MA = 1) External Boot EMI_MODE = 02,3 16-Bit External Address Bus EMI_MODE = 14 20-Bit External Address Bus External Program Memory6 External Program Memory5 External Program Memory5 On-Chip Program RAM 4KB Reserved 92KB Boot Flash 32KB COP Reset Address = 04 0002 Boot Location = 04 0000 Internal Program Flash8 256KB Boot Flash 32KB (Not Used for Boot in this Mode) Internal Program Flash 256KB Internal Program Flash 128KB External Program Memory COP Reset Address = 00 0002 Boot Location = 00 0000 External Program Memory COP Reset Address = 04 00027 Boot Location = 04 00007 P:$03 FFFF P:$02 0000 P:$01 FFFF P:$01 0000 P:$00 FFFF P:$00 0000 Internal Program Flash8 256KB 1. If Flash Security Mode is enabled, EXTBOOT Mode 1 cannot be used. See Security Features, Part 7. 2. This mode provides maximum compatibility with 56F80x parts while operating externally. 3. "EMI_MODE = 0" when EMI_MODE pin is tied to ground at boot up. 4. "EMI_MODE = 1" when EMI_MODE pin is tied to VDD at boot up. 5. Not accessible in reset configuration, since the address is above P:$00 FFFF. The higher bit address/GPIO (and/or chip selects) pins must be reconfigured before this external memory is accessible. 6. Not accessible in reset configuration, since the address is above P:$0F FFFF. The higher bit address/GPIO (and/or chip selects) pins must be reconfigured before this external memory is accessible. 7. Booting from this external address allows prototyping of the internal Boot Flash. 8. Two independent program flash blocks allow one to be programmed/erased while executing from another. Each block must have its own mass erase. 4.3 Interrupt Vector Table Table 4-5 provides the reset and interrupt priority structure, including on-chip peripherals. The table is organized with higher-priority vectors at the top and lower-priority interrupts lower in the table. The priority of an interrupt can be assigned to different levels, as indicated, allowing some control over interrupt priorities. All level 3 interrupts will be serviced before level 2, and so on. For a selected priority level, the lowest vector number has the highest priority. 56F8367 Technical Data, Rev. 3.0 42 Freescale Semiconductor Preliminary Interrupt Vector Table The location of the vector table is determined by the Vector Base Address (VBA) register. Please see Part 5.6.11 for the reset value of the VBA. In some configurations, the reset address and COP reset address will correspond to vector 0 and 1 of the interrupt vector table. In these instances, the first two locations in the vector table must contain branch or JMP instructions. All other entries must contain JSR instructions. Note: PWMA, FlexCAN, Quadrature Decoder 1, and Quad Timers B and D are NOT available on the 56F8167 device. Table 4-5 Interrupt Vector Table Contents1 Peripheral Vector Number Priority Level Vector Base Address + Interrupt Function Reserved for Reset Overlay2 Reserved for COP Reset Overlay2 core core core core core core 2 3 4 5 6 7 3 3 3 3 1-3 1-3 P:$04 P:$06 P:$08 P:$0A P:$0C P:$0E Illegal Instruction SW Interrupt 3 HW Stack Overflow Misaligned Long Word Access OnCE Step Counter OnCE Breakpoint Unit 0 Reserved core core core 9 10 11 1-3 1-3 1-3 P:$12 P:$14 P:$16 OnCE Trace Buffer OnCE Transmit Register Empty OnCE Receive Register Full Reserved core core core core core 14 15 16 17 18 2 1 0 0-2 0-2 P:$1C P:$1E P:$20 P:$22 P:$24 SW Interrupt 2 SW Interrupt 1 SW Interrupt 0 IRQA IRQB Reserved LVI PLL FM FM FM 20 21 22 23 24 0-2 0-2 0-2 0-2 0-2 P:$28 P:$2A P:$2C P:$2E P:$30 Low-Voltage Detector (power sense) PLL FM Access Error Interrupt FM Command Complete FM Command, data and address Buffers Empty Reserved 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 43 Table 4-5 Interrupt Vector Table Contents1 (Continued) Peripheral FLEXCAN FLEXCAN FLEXCAN FLEXCAN GPIOF GPIOE GPIOD GPIOC GPIOB GPIOA Vector Number 26 27 28 29 30 31 32 33 34 35 Priority Level 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 Vector Base Address + P:$34 P:$36 P:$38 P:$3A P:$3C P:$3E P:$40 P:$42 P:$44 P:$46 FLEXCAN Bus Off FLEXCAN Error FLEXCAN Wake Up FLEXCAN Message Buffer Interrupt GPIO F GPIO E GPIO D GPIO C GPIO B GPIO A Reserved SPI1 SPI1 SPI0 SPI0 SCI1 SCI1 38 39 40 41 42 43 0-2 0-2 0-2 0-2 0-2 0-2 P:$4C P:$4E P:$50 P:$52 P:$54 P:$56 SPI 1 Receiver Full SPI 1 Transmitter Empty SPI 0 Receiver Full SPI 0 Transmitter Empty SCI 1 Transmitter Empty SCI 1 Transmitter Idle Reserved SCI1 SCI1 DEC1 DEC1 DEC0 DEC0 45 46 47 48 49 50 0-2 0-2 0-2 0-2 0-2 0-2 P:$5A P:$5C P:$5E P:$60 P:$62 P:$64 SCI 1 Receiver Error SCI 1 Receiver Full Quadrature Decoder #1 Home Switch or Watchdog Quadrature Decoder #1 INDEX Pulse Quadrature Decoder #0 Home Switch or Watchdog Quadrature Decoder #0 INDEX Pulse Reserved TMRD TMRD TMRD TMRD TMRC TMRC TMRC TMRC TMRB 52 53 54 55 56 57 58 59 60 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 P:$68 P:$6A P:$6C P:$6E P:$70 P:$72 P:$74 P:$76 P:$78 Timer D, Channel 0 Timer D, Channel 1 Timer D, Channel 2 Timer D, Channel 3 Timer C, Channel 0 Timer C, Channel 1 Timer C, Channel 2 Timer C, Channel 3 Timer B, Channel 0 Interrupt Function 56F8367 Technical Data, Rev. 3.0 44 Freescale Semiconductor Preliminary Interrupt Vector Table Table 4-5 Interrupt Vector Table Contents1 (Continued) Peripheral TMRB TMRB TMRB TMRA TMRA TMRA TMRA SCI0 SCI0 Vector Number 61 62 63 64 65 66 67 68 69 Priority Level 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 Vector Base Address + P:$7A P:$7C P:$7E P:$80 P:$82 P:$84 P:$86 P:$88 P:$8A Timer B, Channel 1 Timer B, Channel 2 Timer B, Channel 3 Timer A, Channel 0 Timer A, Channel 1 Timer A, Channel 2 Timer A, Channel 3 SCI 0 Transmitter Empty SCI 0 Transmitter Idle Reserved SCI0 SCI0 ADCB ADCA ADCB ADCA PWMB PWMA PWMB PWMA core FLEXCAN2 FLEXCAN2 FLEXCAN2 FLEXCAN2 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 0-2 -1 0-2 0-2 0-2 0-2 P:$8E P:$90 P:$92 P:$94 P:$96 P:$98 P:$9A P:$9C P:$9E P:$A0 P:$A2 P:$A4 P:$A6 P:$A8 P:$AA SCI 0 Receiver Error SCI 0 Receiver Full ADC B Conversion Compete / End of Scan ADC A Conversion Complete / End of Scan ADC B Zero Crossing or Limit Error ADC A Zero Crossing or Limit Error Reload PWM B Reload PWM A PWM B Fault PWM A Fault SW Interrupt LP FlexCAN Bus Off FlexCAN Error FlexCAN Wake Up FlexCAN Message Buffer Interrupt Interrupt Function 1. Two words are allocated for each entry in the vector table. This does not allow the full address range to be referenced from the vector table, providing only 19 bits of address. 2. If the VBA is set to $0200 (or VBA = 0000 for Mode 1, EMI_MODE = 0), the first two locations of the vector table are the chip reset addresses; therefore, these locations are not interrupt vectors. 2. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 45 4.4 Data Map Note: Data Flash is NOT available on the 56F8167 device. Table 4-6 Data Memory Map1 Begin/End Address X:$FF FFFF X:$FF FF00 X:$FF FEFF X:$01 0000 X:$00 FFFF X:$00 F000 X:$00 EFFF X:$00 8000 X:$00 7FFF X:$00 4000 X:$00 3FFF X:$00 0000 EX = 02 EOnCE 256 locations allocated External Memory On-Chip Peripherals 4096 locations allocated External Memory On-Chip Data Flash 32KB On-Chip Data RAM 32KB3 EX = 1 EOnCE 256 locations allocated External Memory On-Chip Peripherals 4096 locations allocated External Memory 1. All addresses are 16-bit Word addresses, not byte addresses. 2. In the Operation Mode Register (OMR). 3. The Data RAM is organized as an 8K x 32-bit memory to allow single-cycle, long-word operations. 4.5 Flash Memory Map Figure 4-1 illustrates the Flash Memory (FM) map on the system bus. The Flash Memory is divided into three functional blocks. The Program and boot memories reside on the Program Memory buses. They are controlled by one set of banked registers. Data Memory Flash resides on the Data Memory buses and is controlled separately by its own set of banked registers. The top nine words of the Program Memory Flash are treated as special memory locations. The content of these words is used to control the operation of the Flash Controller. Because these words are part of the Flash Memory content, their state is maintained during power down and reset. During chip initialization, the content of these memory locations is loaded into Flash Memory control registers, detailed in the Flash Memory chapter of the 56F8300 Peripheral User Manual. These configuration parameters are located between $03_FFF7 and $03_FFFF. 56F8367 Technical Data, Rev. 3.0 46 Freescale Semiconductor Preliminary Flash Memory Map Program Memory BOOT_FLASH_START + $3FFF Data Memory FM_BASE + $14 BOOT_FLASH_START = $04_0000 PROG_FLASH_START + $03_FFFF 32KB Boot Configure Field FM_PROG_MEM_TOP = $01_FFFF Banked Registers Unbanked Registers FM_BASE + $00 DATA_FLASH_START + $3FFF 256KB Program 32KB DATA_FLASH_START + $0000 BLOCK 1 Odd (2 Bytes) $02_0003 BLOCK 1 Even (2 Bytes) $02_0002 BLOCK 1 Odd (2 Bytes) $02_0001 BLOCK 1 Even (2 Bytes) $02_0000 PROG_FLASH_START + $02_0000 PROG_FLASH_START + $01_FFFF Note: Data Flash is NOT available in the 56F8167 device. 256KB Program BLOCK 0 Odd (2 Bytes) $00_0003 BLOCK 0 Even (2 Bytes) $00_0002 BLOCK 0 Odd (2 Bytes) $00_0001 BLOCK 0 Even (2 Bytes) $00_0000 PROG_FLASH_START = $00_0000 Figure 4-1 Flash Array Memory Maps Table 4-7 shows the page and sector sizes used within each Flash memory block on the chip. Note: Data Flash is NOT available on the 56F8167 device. Table 4-7 Flash Memory Partitions Flash Size Program Flash Data Flash Boot Flash 512KB 32KB 32KB Sectors 16 16 4 Sector Size 16K x 16 bits 1024 x 16 bits 4K x 16 bits Page Size 1024 x 16 bits 256 x 16 bits 512 x 16 bits Please see 56F8300 Peripheral User Manual for additional Flash information. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 47 4.6 EOnCE Memory Map Table 4-8 EOnCE Memory Map Address Register Acronym Reserved X:$FF FF8A OESCR External Signal Control Register Reserved X:$FF FF8E OBCNTR Breakpoint Unit [0] Counter Reserved X:$FF FF90 X:$FF FF91 X:$FF FF92 X:$FF FF93 X:$FF FF94 X:$FF FF95 X:$FF FF96 X:$FF FF97 X:$FF FF98 X:$FF FF99 X:$FF FF9A X:$FF FF9B X:$FF FF9C X:$FF FF9D X:$FF FF9E X:$FF FF9F :X:$FF FFA0 OBMSK (32 bits) -- OBAR2 (32 bits) -- OBAR1 (24 bits) -- OBCR (24 bits) -- OTB (21-24 bits/stage) -- OTBPR (8 bits) OTBCR OBASE (8 bits) OSR OSCNTR (24 bits) -- OCR (bits) Breakpoint 1 Unit [0] Mask Register Breakpoint 1 Unit [0] Mask Register Breakpoint 2 Unit [0] Address Register Breakpoint 2 Unit [0] Address Register Breakpoint 1 Unit [0] Address Register Breakpoint 1 Unit [0] Address Register Breakpoint Unit [0] Control Register Breakpoint Unit [0] Control Register Trace Buffer Register Stages Trace Buffer Register Stages Trace Buffer Pointer Register Trace Buffer Control Register Peripheral Base Address Register Status Register Instruction Step Counter Instruction Step Counter Control Register Reserved X:$FF FFFC X:$FF FFFD X:$FF FFFE X:$FF FFFF OCLSR (8 bits) OTXRXSR (8 bits) OTX / ORX (32 bits) OTX1 / ORX1 Core Lock / Unlock Status Register Transmit and Receive Status and Control Register Transmit Register / Receive Register Transmit Register Upper Word Receive Register Upper Word Register Name 56F8367 Technical Data, Rev. 3.0 48 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers 4.7 Peripheral Memory Mapped Registers On-chip peripheral registers are part of the data memory map on the 56800E series. These locations may be accessed with the same addressing modes used for ordinary Data memory, except all peripheral registers should be read/written using word accesses only. Table 4-9 summarizes base addresses for the set of peripherals on the 56F8367 and 56F8167 devices. Peripherals are listed in order of the base address. The following tables list all of the peripheral registers required to control or access the peripherals. Note: Features in italics are NOT available on the 56F8167 device. Table 4-9 Data Memory Peripheral Base Address Map Summary Peripheral External Memory Interface Timer A Timer B Timer C Timer D PWM A PWM B Quadrature Decoder 0 Quadrature Decoder 1 ITCN ADC A ADC B Temperature Sensor SCI #0 SCI #1 SPI #0 SPI #1 COP PLL, OSC GPIO Port A GPIO Port B GPIO Port C GPIO Port D GPIO Port E GPIO Port F EMI TMRA TMRB TMRC TMRD PWMA PWMB DEC0 DEC1 ITCN ADCA ADCB TSENSOR SCI0 SCI1 SPI0 SPI1 COP CLKGEN GPIOA GPIOB GPIOC GPIOD GPIOE GPIOF Prefix Base Address X:$00 F020 X:$00 F040 X:$00 F080 X:$00 F0C0 X:$00 F100 X:$00 F140 X:$00 F160 X:$00 F180 X:$00 F190 X:$00 F1A0 X:$00 F200 X:$00 F240 X:$00 F270 X:$00 F280 X:$00 F290 X:$00 F2A0 X:$00 F2B0 X:$00 F2C0 X:$00 F2D0 X:$00 F2E0 X:$00 F300 X:$00 F310 X:$00 F320 X:$00 F330 X:$00 F340 Table Number 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-21 4-22 4-23 4-24 4-25 4-26 4-27 4-28 4-29 4-30 4-31 4-32 4-33 4-34 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 49 Table 4-9 Data Memory Peripheral Base Address Map Summary (Continued) Peripheral SIM Power Supervisor FM FlexCAN FlexCAN2 SIM LVI FM FC FC2 Prefix Base Address X:$00 F350 X:$00 F360 X:$00 F400 X:$00 F800 X:$00 FA00 Table Number 4-35 4-36 4-37 4-38 4-39 Table 4-10 External Memory Integration Registers Address Map (EMI_BASE = $00 F020) Register Acronym CSBAR 0 Address Offset $0 Register Description Chip Select Base Address Register 0 Reset Value 0x0004 = 64K when EXTBOOT = 0 or EMI_MODE = 0 0x0008 = 1M when EMI_MODE = 1 (Selects entire program space for SC0) CSBAR 1 $1 Chip Select Base Address Register 1 0x0004 = 64K when EMI_MODE = 0 0x0008 = 1M when EMI_MODE = 1 (Selects A0 - 19 addressable data space for CS1) CSBAR 2 CSBAR 3 CSBAR 4 CSBAR 5 CSBAR 6 CSBAR 7 CSOR 0 $2 $3 $4 $5 $6 $7 $8 Chip Select Base Address Register 2 Chip Select Base Address Register 3 Chip Select Base Address Register 4 Chip Select Base Address Register 5 Chip Select Base Address Register 6 Chip Select Base Address Register 7 Chip Select Option Register 0 0x5FCB programmed for chip select for program space, word wide, read and write, 11 waits 0x5FAB programmed for chip select for data space, word wide, read and write, 11 waits CSOR 1 $9 Chip Select Option Register 1 CSOR 2 CSOR 3 CSOR 4 CSOR 5 CSOR 6 CSOR 7 $A $B $C $D $E $F Chip Select Option Register 2 Chip Select Option Register 3 Chip Select Option Register 4 Chip Select Option Register 5 Chip Select Option Register 6 Chip Select Option Register 7 56F8367 Technical Data, Rev. 3.0 50 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-10 External Memory Integration Registers Address Map (Continued) (EMI_BASE = $00 F020) Register Acronym CSTC 0 CSTC 1 CSTC 2 CSTC 3 CSTC 4 CSTC 5 CSTC 6 CSTC 7 BCR Address Offset $10 $11 $12 $13 $14 $15 $16 $17 $18 Register Description Chip Select Timing Control Register 0 Chip Select Timing Control Register 1 Chip Select Timing Control Register 2 Chip Select Timing Control Register 3 Chip Select Timing Control Register 4 Chip Select Timing Control Register 5 Chip Select Timing Control Register 6 Chip Select Timing Control Register 7 Bus Control Register 0x016B sets the default number of wait states to 11 for both read and write accesses Reset Value Table 4-11 Quad Timer A Registers Address Map (TMRA_BASE = $00 F040) Register Acronym TMRA0_CMP1 TMRA0_CMP2 TMRA0_CAP TMRA0_LOAD TMRA0_HOLD TMRA0_CNTR TMRA0_CTRL TMRA0_SCR TMRA0_CMPLD1 TMRA0_CMPLD2 TMRA0_COMSCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRA1_CMP1 TMRA1_CMP2 TMRA1_CAP TMRA1_LOAD TMRA1_HOLD TMRA1_CNTR TMRA1_CTRL TMRA1_SCR $10 $11 $12 $13 $14 $15 $16 $17 Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 51 Table 4-11 Quad Timer A Registers Address Map (Continued) (TMRA_BASE = $00 F040) Register Acronym TMRA1_CMPLD1 TMRA1_CMPLD2 TMRA1_COMSCR Address Offset $18 $19 $1A Register Description Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRA2_CMP1 TMRA2_CMP2 TMRA2_CAP TMRA2_LOAD TMRA2_HOLD TMRA2_CNTR TMRA2_CTRL TMRA2_SCR TMRA2_CMPLD1 TMRA2_CMPLD2 TMRA2_COMSCR $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRA3_CMP1 TMRA3_CMP2 TMRA3_CAP TMRA3_LOAD TMRA3_HOLD TMRA3_CNTR TMRA3_CTRL TMRA3_SCR TMRA3_CMPLD1 TMRA3_CMPLD2 TMRA3_COMSCR $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Table 4-12 Quad Timer B Registers Address Map (TMRB_BASE = $00 F080) Quad Timer B is NOT available in the 56F8167 device Register Acronym TMRB0_CMP1 TMRB0_CMP2 TMRB0_CAP TMRB0_LOAD TMRB0_HOLD 52 Address Offset $0 $1 $2 $3 Register Description Compare Register 1 Compare Register 2 Capture Register Load Register $4 Hold Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-12 Quad Timer B Registers Address Map (Continued) (TMRB_BASE = $00 F080) Quad Timer B is NOT available in the 56F8167 device Register Acronym TMRB0_CNTR TMRB0_CTRL TMRB0_SCR TMRB0_CMPLD1 TMRB0_CMPLD2 TMRB0_COMSCR Address Offset $5 $6 $7 $8 $9 $A Register Description Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRB1_CMP1 TMRB1_CMP2 TMRB1_CAP TMRB1_LOAD TMRB1_HOLD TMRB1_CNTR TMRB1_CTRL TMRB1_SCR TMRB1_CMPLD1 TMRB1_CMPLD2 TMRB1_COMSCR $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRB2_CMP1 TMRB2_CMP2 TMRB2_CAP TMRB2_LOAD TMRB2_HOLD TMRB2_CNTR TMRB2_CTRL TMRB2_SCR TMRB2_CMPLD1 TMRB2_CMPLD2 TMRB2_COMSCR $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRB3_CMP1 TMRB3_CMP2 $30 $31 Compare Register 1 Compare Register 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 53 Table 4-12 Quad Timer B Registers Address Map (Continued) (TMRB_BASE = $00 F080) Quad Timer B is NOT available in the 56F8167 device Register Acronym TMRB3_CAP TMRB3_LOAD TMRB3_HOLD TMRB3_CNTR TMRB3_CTRL TMRB3_SCR TMRB3_CMPLD1 TMRB3_CMPLD2 TMRB3_COMSCR Address Offset $32 $33 $34 $35 $36 $37 $38 $39 $3A Register Description Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Table 4-13 Quad Timer C Registers Address Map (TMRC_BASE = $00 F0C0) Register Acronym TMRC0_CMP1 TMRC0_CMP2 TMRC0_CAP TMRC0_LOAD TMRC0_HOLD TMRC0_CNTR TMRC0_CTRL TMRC0_SCR TMRC0_CMPLD1 TMRC0_CMPLD2 TMRC0_COMSCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRC1_CMP1 TMRC1_CMP2 TMRC1_CAP TMRC1_LOAD TMRC1_HOLD TMRC1_CNTR TMRC1_CTRL TMRC1_SCR $10 $11 $12 $13 $14 $15 $16 $17 Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register 56F8367 Technical Data, Rev. 3.0 54 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-13 Quad Timer C Registers Address Map (Continued) (TMRC_BASE = $00 F0C0) Register Acronym TMRC1_CMPLD1 TMRC1_CMPLD2 TMRC1_COMSCR Address Offset $18 $19 $1A Register Description Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRC2_CMP1 TMRC2_CMP2 TMRC2_CAP TMRC2_LOAD TMRC2_HOLD TMRC2_CNTR TMRC2_CTRL TMRC2_SCR TMRC2_CMPLD1 TMRC2_CMPLD2 TMRC2_COMSCR $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRC3_CMP1 TMRC3_CMP2 TMRC3_CAP TMRC3_LOAD TMRC3_HOLD TMRC3_CNTR TMRC3_CTRL TMRC3_SCR TMRC3_CMPLD1 TMRC3_CMPLD2 TMRC3_COMSCR $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 55 Table 4-14 Quad Timer D Registers Address Map (TMRD_BASE = $00 F100) Quad Timer D is NOT available in the 56F8167 device Register Acronym TMRD0_CMP1 TMRD0_CMP2 TMRD0_CAP TMRD0_LOAD TMRD0_HOLD TMRD0_CNTR TMRD0_CTRL TMRD0_SCR TMRD0_CMPLD1 TMRD0_CMPLD2 TMRD0_COMSCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRD1_CMP1 TMRD1_CMP2 TMRD1_CAP TMRD1_LOAD TMRD1_HOLD TMRD1_CNTR TMRD1_CTRL TMRD1_SCR TMRD1_CMPLD1 TMRD1_CMPLD2 TMRD1_COMSCR $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRD2_CMP1 TMRD2_CMP2 TMRD2_CAP TMRD2_LOAD TMRD2_HOLD TMRD2_CNTR TMRD2_CTRL TMRD2_SCR $20 $21 $22 $23 $24 $25 $26 $27 Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register 56F8367 Technical Data, Rev. 3.0 56 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-14 Quad Timer D Registers Address Map (Continued) (TMRD_BASE = $00 F100) Quad Timer D is NOT available in the 56F8167 device Register Acronym TMRD2_CMPLD1 TMRD2_CMPLD2 TMRD2_COMSCR Address Offset $28 $29 $2A Register Description Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Reserved TMRD3_CMP1 TMRD3_CMP2 TMRD3_CAP TMRD3_LOAD TMRD3_HOLD TMRD3_CNTR TMRD3_CTRL TMRD3_SCR TMRD3_CMPLD1 TMRD3_CMPLD2 TMRD3_COMSCR $30 $31 $32 $33 $34 $35 $36 $37 $38 $39 $3A Compare Register 1 Compare Register 2 Capture Register Load Register Hold Register Counter Register Control Register Status and Control Register Comparator Load Register 1 Comparator Load Register 2 Comparator Status and Control Register Table 4-15 Pulse Width Modulator A Registers Address Map (PWMA_BASE = $00 F140) PWMA is NOT available in the 56F8167 device Register Acronym PWMA_PMCTL PWMA_PMFCTL PWMA_PMFSA PWMA_PMOUT PWMA_PMCNT PWMA_PWMCM PWMA_PWMVAL0 PWMA_PWMVAL1 PWMA_PWMVAL2 PWMA_PWMVAL3 PWMA_PWMVAL4 PWMA_PWMVAL5 PWMA_PMDEADTM Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C Control Register Fault Control Register Fault Status Acknowledge Register Output Control Register Counter Register Counter Modulo Register Value Register 0 Value Register 1 Value Register 2 Value Register 3 Value Register 4 Value Register 5 Dead Time Register Register Description 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 57 Table 4-15 Pulse Width Modulator A Registers Address Map (Continued) (PWMA_BASE = $00 F140) PWMA is NOT available in the 56F8167 device Register Acronym PWMA_PMDISMAP1 PWMA_PMDISMAP2 PWMA_PMCFG PWMA_PMCCR PWMA_PMPORT PWMA_PMICCR Address Offset $D $E $F $10 $11 $12 Register Description Disable Mapping Register 1 Disable Mapping Register 2 Configure Register Channel Control Register Port Register PWM Internal Correction Control Register Table 4-16 Pulse Width Modulator B Registers Address Map (PWMB_BASE = $00 F160) Register Acronym PWMB_PMCTL PWMB_PMFCTL PWMB_PMFSA PWMB_PMOUT PWMB_PMCNT PWMB_PWMCM PWMB_PWMVAL0 PWMB_PWMVAL1 PWMB_PWMVAL2 PWMB_PWMVAL3 PWMB_PWMVAL4 PWMB_PWMVAL5 PWMB_PMDEADTM PWMB_PMDISMAP1 PWMB_PMDISMAP2 PWMB_PMCFG PWMB_PMCCR PWMB_PMPORT PWMB_PMICCR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 Control Register Fault Control Register Fault Status Acknowledge Register Output Control Register Counter Register Counter Modulo Register Value Register 0 Value Register 1 Value Register 2 Value Register 3 Value Register 4 Value Register 5 Dead Time Register Disable Mapping Register 1 Disable Mapping Register 2 Configure Register Channel Control Register Port Register PWM Internal Correction Control Register Register Description 56F8367 Technical Data, Rev. 3.0 58 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-17 Quadrature Decoder 0 Registers Address Map (DEC0_BASE = $00 F180) Register Acronym DEC0_DECCR DEC0_FIR DEC0_WTR DEC0_POSD DEC0_POSDH DEC0_REV DEC0_REVH DEC0_UPOS DEC0_LPOS DEC0_UPOSH DEC0_LPOSH DEC0_UIR DEC0_LIR DEC0_IMR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D Register Description Decoder Control Register Filter Interval Register Watchdog Time-out Register Position Difference Counter Register Position Difference Counter Hold Register Revolution Counter Register Revolution Hold Register Upper Position Counter Register Lower Position Counter Register Upper Position Hold Register Lower Position Hold Register Upper Initialization Register Lower Initialization Register Input Monitor Register Table 4-18 Quadrature Decoder 1 Registers Address Map (DEC1_BASE = $00 F190) Quadrature Decoder 1 is NOT available in the 56F8167 device Register Acronym DEC1_DECCR DEC1_FIR DEC1_WTR DEC1_POSD DEC1_POSDH DEC1_REV DEC1_REVH DEC1_UPOS DEC1_LPOS DEC1_UPOSH DEC1_LPOSH DEC1_UIR DEC1_LIR DEC1_IMR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D Register Description Decoder Control Register Filter Interval Register Watchdog Time-out Register Position Difference Counter Register Position Difference Counter Hold Register Revolution Counter Register Revolution Hold Register Upper Position Counter Register Lower Position Counter Register Upper Position Hold Register Lower Position Hold Register Upper Initialization Register Lower Initialization Register Input Monitor Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 59 Table 4-19 Interrupt Control Registers Address Map (ITCN_BASE = $00 F1A0) Register Acronym IPR 0 IPR 1 IPR 2 IPR 3 IPR 4 IPR 5 IPR 6 IPR 7 IPR 8 IPR 9 VBA FIM0 FIVAL0 FIVAH0 FIM1 FIVAL1 FIVAH1 IRQP 0 IRQP 1 IRQP 2 IRQP 3 IRQP 4 IRQP 5 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 Register Description Interrupt Priority Register 0 Interrupt Priority Register 1 Interrupt Priority Register 2 Interrupt Priority Register 3 Interrupt Priority Register 4 Interrupt Priority Register 5 Interrupt Priority Register 6 Interrupt Priority Register 7 Interrupt Priority Register 8 Interrupt Priority Register 9 Vector Base Address Register Fast Interrupt Match Register 0 Fast Interrupt Vector Address Low 0 Register Fast Interrupt Vector Address High 0 Register Fast Interrupt Match Register 1 Fast Interrupt Vector Address Low 1 Register Fast Interrupt Vector Address High 1 Register IRQ Pending Register 0 IRQ Pending Register 1 IRQ Pending Register 2 IRQ Pending Register 3 IRQ Pending Register 4 IRQ Pending Register 5 Reserved ICTL $1D Interrupt Control Register Reserved IPR10 $1F Interrupt Priority Register 10 56F8367 Technical Data, Rev. 3.0 60 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-20 Analog-to-Digital Converter Registers Address Map (ADCA_BASE = $00 F200) Register Acronym ADCA_CR 1 ADCA_CR 2 ADCA_ZCC ADCA_LST 1 ADCA_LST 2 ADCA_SDIS ADCA_STAT ADCA_LSTAT ADCA_ZCSTAT ADCA_RSLT 0 ADCA_RSLT 1 ADCA_RSLT 2 ADCA_RSLT 3 ADCA_RSLT 4 ADCA_RSLT 5 ADCA_RSLT 6 ADCA_RSLT 7 ADCA_LLMT 0 ADCA_LLMT 1 ADCA_LLMT 2 ADCA_LLMT 3 ADCA_LLMT 4 ADCA_LLMT 5 ADCA_LLMT 6 ADCA_LLMT 7 ADCA_HLMT 0 ADCA_HLMT 1 ADCA_HLMT 2 ADCA_HLMT 3 ADCA_HLMT 4 ADCA_HLMT 5 ADCA_HLMT 6 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A $1B $1C $1D $1E $1F Register Description Control Register 1 Control Register 2 Zero Crossing Control Register Channel List Register 1 Channel List Register 2 Sample Disable Register Status Register Limit Status Register Zero Crossing Status Register Result Register 0 Result Register 1 Result Register 2 Result Register 3 Result Register 4 Result Register 5 Result Register 6 Result Register 7 Low Limit Register 0 Low Limit Register 1 Low Limit Register 2 Low Limit Register 3 Low Limit Register 4 Low Limit Register 5 Low Limit Register 6 Low Limit Register 7 High Limit Register 0 High Limit Register 1 High Limit Register 2 High Limit Register 3 High Limit Register 4 High Limit Register 5 High Limit Register 6 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 61 Table 4-20 Analog-to-Digital Converter Registers Address Map (Continued) (ADCA_BASE = $00 F200) Register Acronym ADCA_HLMT 7 ADCA_OFS 0 ADCA_OFS 1 ADCA_OFS 2 ADCA_OFS 3 ADCA_OFS 4 ADCA_OFS 5 ADCA_OFS 6 ADCA_OFS 7 ADCA_POWER ADCA_CAL Address Offset $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Register Description High Limit Register 7 Offset Register 0 Offset Register 1 Offset Register 2 Offset Register 3 Offset Register 4 Offset Register 5 Offset Register 6 Offset Register 7 Power Control Register ADC Calibration Register Table 4-21 Analog-to-Digital Converter Registers Address Map (ADCB_BASE = $00 F240) Register Acronym ADCB_CR 1 ADCB_CR 2 ADCB_ZCC ADCB_LST 1 ADCB_LST 2 ADCB_SDIS ADCB_STAT ADCB_LSTAT ADCB_ZCSTAT ADCB_RSLT 0 ADCB_RSLT 1 ADCB_RSLT 2 ADCB_RSLT 3 ADCB_RSLT 4 ADCB_RSLT 5 ADCB_RSLT 6 ADCB_RSLT 7 ADCB_LLMT 0 ADCB_LLMT 1 Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 Register Description Control Register 1 Control Register 2 Zero Crossing Control Register Channel List Register 1 Channel List Register 2 Sample Disable Register Status Register Limit Status Register Zero Crossing Status Register Result Register 0 Result Register 1 Result Register 2 Result Register 3 Result Register 4 Result Register 5 Result Register 6 Result Register 7 Low Limit Register 0 Low Limit Register 1 56F8367 Technical Data, Rev. 3.0 62 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-21 Analog-to-Digital Converter Registers Address Map (Continued) (ADCB_BASE = $00 F240) Register Acronym ADCB_LLMT 2 ADCB_LLMT 3 ADCB_LLMT 4 ADCB_LLMT 5 ADCB_LLMT 6 ADCB_LLMT 7 ADCB_HLMT 0 ADCB_HLMT 1 ADCB_HLMT 2 ADCB_HLMT 3 ADCB_HLMT 4 ADCB_HLMT 5 ADCB_HLMT 6 ADCB_HLMT 7 ADCB_OFS 0 ADCB_OFS 1 ADCB_OFS 2 ADCB_OFS 3 ADCB_OFS 4 ADCB_OFS 5 ADCB_OFS 6 ADCB_OFS 7 ADCB_POWER ADCB_CAL Address Offset $13 $14 $15 $16 $17 $18 $19 $1A $1B $1C $1D $1E $1F $20 $21 $22 $23 $24 $25 $26 $27 $28 $29 $2A Register Description Low Limit Register 2 Low Limit Register 3 Low Limit Register 4 Low Limit Register 5 Low Limit Register 6 Low Limit Register 7 High Limit Register 0 High Limit Register 1 High Limit Register 2 High Limit Register 3 High Limit Register 4 High Limit Register 5 High Limit Register 6 High Limit Register 7 Offset Register 0 Offset Register 1 Offset Register 2 Offset Register 3 Offset Register 4 Offset Register 5 Offset Register 6 Offset Register 7 Power Control Register ADC Calibration Register Table 4-22 Temperature Sensor Register Address Map (TSENSOR_BASE = $00 F270) Temperature Sensor is NOT available in the 56F8167 device Register Acronym TSENSOR_CNTL Address Offset $0 Control Register Register Description 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 63 Table 4-23 Serial Communication Interface 0 Registers Address Map (SCI0_BASE = $00 F280) Register Acronym SCI0_SCIBR SCI0_SCICR Address Offset $0 $1 Register Description Baud Rate Register Control Register Reserved SCI0_SCISR SCI0_SCIDR $3 $4 Status Register Data Register Table 4-24 Serial Communication Interface 1 Registers Address Map (SCI1_BASE = $00 F290) Register Acronym SCI1_SCIBR SCI1_SCICR Address Offset $0 $1 Register Description Baud Rate Register Control Register Reserved SCI1_SCISR SCI1_SCIDR $3 $4 Status Register Data Register Table 4-25 Serial Peripheral Interface 0 Registers Address Map (SPI0_BASE = $00 F2A0) Register Acronym SPI0_SPSCR SPI0_SPDSR SPI0_SPDRR SPI0_SPDTR Address Offset $0 $1 $2 $3 Register Description Status and Control Register Data Size Register Data Receive Register Data Transmitter Register Table 4-26 Serial Peripheral Interface 1 Registers Address Map (SPI1_BASE = $00 F2B0) Register Acronym SPI1_SPSCR SPI1_SPDSR SPI1_SPDRR SPI1_SPDTR Address Offset $0 $1 $2 $3 Register Description Status and Control Register Data Size Register Data Receive Register Data Transmitter Register 56F8367 Technical Data, Rev. 3.0 64 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-27 Computer Operating Properly Registers Address Map (COP_BASE = $00 F2C0) Register Acronym COPCTL COPTO COPCTR Address Offset $0 $1 $2 Control Register Time Out Register Counter Register Register Description Table 4-28 Clock Generation Module Registers Address Map (CLKGEN_BASE = $00 F2D0) Register Acronym PLLCR PLLDB PLLSR Address Offset $0 $1 $2 Control Register Divide-By Register Status Register Reserved SHUTDOWN OSCTL $4 $5 Shutdown Register Oscillator Control Register Register Description Table 4-29 GPIOA Registers Address Map (GPIOA_BASE = $00 F2E0) Register Acronym GPIOA_PUR GPIOA_DR GPIOA_DDR GPIOA_PER GPIOA_IAR GPIOA_IENR GPIOA_IPOLR GPIOA_IPR GPIOA_IESR GPIOA_PPMODE GPIOA_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 3FFF 0 x 0000 0 x 0000 0 x 3FFF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 3FFF -- 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 65 Table 4-30 GPIOB Registers Address Map (GPIOB_BASE = $00 F300) Register Acronym GPIOB_PUR GPIOB_DR GPIOB_DDR GPIOB_PER Address Offset $0 $1 $2 $3 Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Reset Value 0 x 00FF 0 x 0000 0 x 0000 0 x 000F for 20-bit EMI address at reset. 0 x 0000 for all other cases. See Table 4-4 for details. GPIOB_IAR GPIOB_IENR GPIOB_IPOLR GPIOB_IPR GPIOB_IESR GPIOB_PPMODE GPIOB_RAWDATA $4 $5 $6 $7 $8 $9 $A Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 -- Table 4-31 GPIOC Registers Address Map (GPIOC_BASE = $00F310) Register Acronym GPIOC_PUR GPIOC_DR GPIOC_DDR GPIOC_PER GPIOC_IAR GPIOC_IENR GPIOC_IPOLR GPIOC_IPR GPIOC_IESR GPIOC_PPMODE GPIOC_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 07FF 0 x 0000 0 x 0000 0 x 07FF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 07FF -- 56F8367 Technical Data, Rev. 3.0 66 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-32 GPIOD Registers Address Map (GPIOD_BASE = $00 F320) Register Acronym GPIOD_PUR GPIOD_DR GPIOD_DDR GPIOD_PER GPIOD_IAR GPIOD_IENR GPIOD_IPOLR GPIOD_IPR GPIOD_IESR GPIOD_PPMODE GPIOD_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register -- Reset Value 0 x 1FFF 0 x 0000 0 x 0000 0 x 1FC0 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 Table 4-33 GPIOE Registers Address Map (GPIOE_BASE = $00 F330) Register Acronym GPIOE_PUR GPIOE_DR GPIOE_DDR GPIOE_PER GPIOE_IAR GPIOE_IENR GPIOE_IPOLR GPIOE_IPR GPIOE_IESR GPIOE_PPMODE GPIOE_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x 3FFF 0 x 0000 0 x 0000 0 x 3FFF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 3FFF -- 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 67 Table 4-34 GPIOF Registers Address Map (GPIOF_BASE = $00 F340) Register Acronym GPIOF_PUR GPIOF_DR GPIOF_DDR GPIOF_PER GPIOF_IAR GPIOF_IENR GPIOF_IPOLR GPIOF_IPR GPIOF_IESR GPIOF_PPMODE GPIOF_RAWDATA Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A Register Description Pull-up Enable Register Data Register Data Direction Register Peripheral Enable Register Interrupt Assert Register Interrupt Enable Register Interrupt Polarity Register Interrupt Pending Register Interrupt Edge-Sensitive Register Push-Pull Mode Register Raw Data Input Register Reset Value 0 x FFFF 0 x 0000 0 x 0000 0 x FFFF 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x 0000 0 x FFFF -- Table 4-35 System Integration Module Registers Address Map (SIM_BASE = $00 F350) Register Acronym SIM_CONTROL SIM_RSTSTS SIM_SCR0 SIM_SCR1 SIM_SCR2 SIM_SCR3 SIM_MSH_ID SIM_LSH_ID SIM_PUDR Address Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 Control Register Reset Status Register Software Control Register 0 Software Control Register 1 Software Control Register 2 Software Control Register 3 Most Significant Half JTAG ID Least Significant Half JTAG ID Pull-up Disable Register Reserved SIM_CLKOSR SIM_GPS SIM_PCE SIM_ISALH SIM_ISALL SIM_PCE2 $A $B $C $D $E $F Clock Out Select Register Quad Decoder 1 / Timer B / SPI 1 Select Register Peripheral Clock Enable Register I/O Short Address Location High Register I/O Short Address Location Low Register Peripheral Clock Enable Register 2 Register Description 56F8367 Technical Data, Rev. 3.0 68 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-36 Power Supervisor Registers Address Map (LVI_BASE = $00 F360) Register Acronym LVI_CONTROL LVI_STATUS Address Offset $0 $1 Control Register Status Register Register Description Table 4-37 Flash Module Registers Address Map (FM_BASE = $00 F400) Register Acronym FMCLKD FMMCR Address Offset $0 $1 Register Description Clock Divider Register Module Control Register Reserved FMSECH FMSECL $3 $4 Security High Half Register Security Low Half Register Reserved Reserved FMPROT FMPROTB $10 $11 Protection Register (Banked) Protection Boot Register (Banked) Reserved FMUSTAT FMCMD $13 $14 User Status Register (Banked) Command Register (Banked) Reserved Reserved FMOPT 0 $1A 16-Bit Information Option Register 0 Hot temperature ADC reading of Temperature Sensor; value set during factory test 16-Bit Information Option Register 1 Not used 16-Bit Information Option Register 2 Room temperature ADC reading of Temperature Sensor; value set during factory test FMOPT 1 FMOPT 2 $1B $1C 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 69 Table 4-38 FlexCAN Registers Address Map (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8167 device Register Acronym FCMCR Address Offset $0 Register Description Module Configuration Register Reserved FCCTL0 FCCTL1 FCTMR FCMAXMB $3 $4 $5 $6 Control Register 0 Register Control Register 1 Register Free-Running Timer Register Maximum Message Buffer Configuration Register Reserved FCRXGMASK_H FCRXGMASK_L FCRX14MASK_H FCRX14MASK_L FCRX15MASK_H FCRX15MASK_L $8 $9 $A $B $C $D Receive Global Mask High Register Receive Global Mask Low Register Receive Buffer 14 Mask High Register Receive Buffer 14 Mask Low Register Receive Buffer 15 Mask High Register Receive Buffer 15 Mask Low Register Reserved FCSTATUS FCIMASK1 FCIFLAG1 FCR/T_ERROR_CNTRS $10 $11 $12 $13 Error and Status Register Interrupt Masks 1 Register Interrupt Flags 1 Register Receive and Transmit Error Counters Register Reserved Reserved Reserved FCMB0_CONTROL FCMB0_ID_HIGH FCMB0_ID_LOW FCMB0_DATA FCMB0_DATA FCMB0_DATA FCMB0_DATA $40 $41 $42 $43 $44 $45 $46 Message Buffer 0 Control / Status Register Message Buffer 0 ID High Register Message Buffer 0 ID Low Register Message Buffer 0 Data Register Message Buffer 0 Data Register Message Buffer 0 Data Register Message Buffer 0 Data Register Reserved FCMSB1_CONTROL FCMSB1_ID_HIGH FCMSB1_ID_LOW $48 $49 $4A Message Buffer 1 Control / Status Register Message Buffer 1 ID High Register Message Buffer 1 ID Low Register 56F8367 Technical Data, Rev. 3.0 70 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8167 device Register Acronym FCMB1_DATA FCMB1_DATA FCMB1_DATA FCMB1_DATA Address Offset $4B $4C $4D $4E Register Description Message Buffer 1 Data Register Message Buffer 1 Data Register Message Buffer 1 Data Register Message Buffer 1 Data Register Reserved FCMB2_CONTROL FCMB2_ID_HIGH FCMB2_ID_LOW FCMB2_DATA FCMB2_DATA FCMB2_DATA FCMB2_DATA $50 $51 $52 $53 $54 $55 $56 Message Buffer 2 Control / Status Register Message Buffer 2 ID High Register Message Buffer 2 ID Low Register Message Buffer 2 Data Register Message Buffer 2 Data Register Message Buffer 2 Data Register Message Buffer 2 Data Register Reserved FCMB3_CONTROL FCMB3_ID_HIGH FCMB3_ID_LOW FCMB3_DATA FCMB3_DATA FCMB3_DATA FCMB3_DATA $58 $59 $5A $5B $5C $5D $5E Message Buffer 3 Control / Status Register Message Buffer 3 ID High Register Message Buffer 3 ID Low Register Message Buffer 3 Data Register Message Buffer 3 Data Register Message Buffer 3 Data Register Message Buffer 3 Data Register Reserved FCMB4_CONTROL FCMB4_ID_HIGH FCMB4_ID_LOW FCMB4_DATA FCMB4_DATA FCMB4_DATA FCMB4_DATA $60 $61 $62 $63 $64 $65 $66 Message Buffer 4 Control / Status Register Message Buffer 4 ID High Register Message Buffer 4 ID Low Register Message Buffer 4 Data Register Message Buffer 4 Data Register Message Buffer 4 Data Register Message Buffer 4 Data Register Reserved FCMB5_CONTROL FCMB5_ID_HIGH FCMB5_ID_LOW $68 $69 $6A Message Buffer 5 Control / Status Register Message Buffer 5 ID High Register Message Buffer 5 ID Low Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 71 Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8167 device Register Acronym FCMB5_DATA FCMB5_DATA FCMB5_DATA FCMB5_DATA Address Offset $6B $6C $6D $6E Register Description Message Buffer 5 Data Register Message Buffer 5 Data Register Message Buffer 5 Data Register Message Buffer 5 Data Register Reserved FCMB6_CONTROL FCMB6_ID_HIGH FCMB6_ID_LOW FCMB6_DATA FCMB6_DATA FCMB6_DATA FCMB6_DATA $70 $71 $72 $73 $74 $75 $76 Message Buffer 6 Control / Status Register Message Buffer 6 ID High Register Message Buffer 6 ID Low Register Message Buffer 6 Data Register Message Buffer 6 Data Register Message Buffer 6 Data Register Message Buffer 6 Data Register Reserved FCMB7_CONTROL FCMB7_ID_HIGH FCMB7_ID_LOW FCMB7_DATA FCMB7_DATA FCMB7_DATA FCMB7_DATA $78 $79 $7A $7B $7C $7D $7E Message Buffer 7 Control / Status Register Message Buffer 7 ID High Register Message Buffer 7 ID Low Register Message Buffer 7 Data Register Message Buffer 7 Data Register Message Buffer 7 Data Register Message Buffer 7 Data Register Reserved FCMB8_CONTROL FCMB8_ID_HIGH FCMB8_ID_LOW FCMB8_DATA FCMB8_DATA FCMB8_DATA FCMB8_DATA $80 $81 $82 $83 $84 $85 $86 Message Buffer 8 Control / Status Register Message Buffer 8 ID High Register Message Buffer 8 ID Low Register Message Buffer 8 Data Register Message Buffer 8 Data Register Message Buffer 8 Data Register Message Buffer 8 Data Register Reserved FCMB9_CONTROL FCMB9_ID_HIGH FCMB9_ID_LOW $88 $89 $8A Message Buffer 9 Control / Status Register Message Buffer 9 ID High Register Message Buffer 9 ID Low Register 56F8367 Technical Data, Rev. 3.0 72 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8167 device Register Acronym FCMB9_DATA FCMB9_DATA FCMB9_DATA FCMB9_DATA Address Offset $8B $8C $8D $8E Register Description Message Buffer 9 Data Register Message Buffer 9 Data Register Message Buffer 9 Data Register Message Buffer 9 Data Register Reserved FCMB10_CONTROL FCMB10_ID_HIGH FCMB10_ID_LOW FCMB10_DATA FCMB10_DATA FCMB10_DATA FCMB10_DATA $90 $91 $92 $93 $94 $95 $96 Message Buffer 10 Control / Status Register Message Buffer 10 ID High Register Message Buffer 10 ID Low Register Message Buffer 10 Data Register Message Buffer 10 Data Register Message Buffer 10 Data Register Message Buffer 10 Data Register Reserved FCMB11_CONTROL FCMB11_ID_HIGH FCMB11_ID_LOW FCMB11_DATA FCMB11_DATA FCMB11_DATA FCMB11_DATA $98 $99 $9A $9B $9C $9D $9E Message Buffer 11 Control / Status Register Message Buffer 11 ID High Register Message Buffer 11 ID Low Register Message Buffer 11 Data Register Message Buffer 11 Data Register Message Buffer 11 Data Register Message Buffer 11 Data Register Reserved FCMB12_CONTROL FCMB12_ID_HIGH FCMB12_ID_LOW FCMB12_DATA FCMB12_DATA FCMB12_DATA FCMB12_DATA $A0 $A1 $A2 $A3 $A4 $A5 $A6 Message Buffer 12 Control / Status Register Message Buffer 12 ID High Register Message Buffer 12 ID Low Register Message Buffer 12 Data Register Message Buffer 12 Data Register Message Buffer 12 Data Register Message Buffer 12 Data Register Reserved FCMB13_CONTROL FCMB13_ID_HIGH FCMB13_ID_LOW $A8 $A9 $AA Message Buffer 13 Control / Status Register Message Buffer 13 ID High Register Message Buffer 13 ID Low Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 73 Table 4-38 FlexCAN Registers Address Map (Continued) (FC_BASE = $00 F800) FlexCAN is NOT available in the 56F8167 device Register Acronym FCMB13_DATA FCMB13_DATA FCMB13_DATA FCMB13_DATA Address Offset $AB $AC $AD $AE Register Description Message Buffer 13 Data Register Message Buffer 13 Data Register Message Buffer 13 Data Register Message Buffer 13 Data Register Reserved FCMB14_CONTROL FCMB14_ID_HIGH FCMB14_ID_LOW FCMB14_DATA FCMB14_DATA FCMB14_DATA FCMB14_DATA $B0 $B1 $B2 $B3 $B4 $B5 $B6 Message Buffer 14 Control / Status Register Message Buffer 14 ID High Register Message Buffer 14 ID Low Register Message Buffer 14 Data Register Message Buffer 14 Data Register Message Buffer 14 Data Register Message Buffer 14 Data Register Reserved FCMB15_CONTROL FCMB15_ID_HIGH FCMB15_ID_LOW FCMB15_DATA FCMB15_DATA FCMB15_DATA FCMB15_DATA $B8 $B9 $BA $BB $BC $BD $BE Message Buffer 15 Control / Status Register Message Buffer 15 ID High Register Message Buffer 15 ID Low Register Message Buffer 15 Data Register Message Buffer 15 Data Register Message Buffer 15 Data Register Message Buffer 15 Data Register Reserved Table 4-39 FlexCAN2 Registers Address Map (FC2_BASE = $00 FA00) FlexCAN2 is NOT available in the 56F8167 device Register Acronym FC2MCR Address Offset $0 Register Description Module Configuration Register Reserved FC2CTL0 FC2CTL1 FC2TMR FC2MAXMB FC2IMASK2 FC2RXGMASK_H $3 $4 $5 $6 $7 $8 Control Register 0 Register Control Register 1 Register Free-Running Timer Register Maximum Message Buffer Configuration Register Interrupt Masks 2 Register Receive Global Mask High Register 56F8367 Technical Data, Rev. 3.0 74 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-39 FlexCAN2 Registers Address Map (Continued) (FC2_BASE = $00 FA00) FlexCAN2 is NOT available in the 56F8167 device Register Acronym FC2RXGMASK_L FC2RX14MASK_H FC2RX14MASK_L FC2RX15MASK_H FC2RX15MASK_L Address Offset $9 $A $B $C $D Register Description Receive Global Mask Low Register Receive Buffer 14 Mask High Register Receive Buffer 14 Mask Low Register Receive Buffer 15 Mask High Register Receive Buffer 15 Mask Low Register Reserved FC2STATUS FC2IMASK1 FC2IFLAG1 FC2R/T_ERROR_CNTRS $10 $11 $12 $13 Error and Status Register Interrupt Masks 1 Register Interrupt Flags 1 Register Receive and Transmit Error Counters Register Reserved FC2IFLAG 2 $1B Interrupt Flags 2 Register Reserved FC2MB0_CONTROL FC2MB0_ID_HIGH FC2MB0_ID_LOW FC2MB0_DATA FC2MB0_DATA FC2MB0_DATA FC2MB0_DATA $40 $41 $42 $43 $44 $45 $46 Message Buffer 0 Control / Status Register Message Buffer 0 ID High Register Message Buffer 0 ID Low Register Message Buffer 0 Data Register Message Buffer 0 Data Register Message Buffer 0 Data Register Message Buffer 0 Data Register Reserved FC2MSB1_CONTROL FC2MSB1_ID_HIGH FC2MSB1_ID_LOW FC2MB1_DATA FC2MB1_DATA FC2MB1_DATA FC2MB1_DATA $48 $49 $4A $4B $4C $4D $4E Message Buffer 1 Control / Status Register Message Buffer 1 ID High Register Message Buffer 1 ID Low Register Message Buffer 1 Data Register Message Buffer 1 Data Register Message Buffer 1 Data Register Message Buffer 1 Data Register Reserved FC2MB2_CONTROL FC2MB2_ID_HIGH FC2MB2_ID_LOW $50 $51 $52 Message Buffer 2 Control / Status Register Message Buffer 2 ID High Register Message Buffer 2 ID Low Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 75 Table 4-39 FlexCAN2 Registers Address Map (Continued) (FC2_BASE = $00 FA00) FlexCAN2 is NOT available in the 56F8167 device Register Acronym FC2MB2_DATA FC2MB2_DATA FC2MB2_DATA FC2MB2_DATA Address Offset $53 $54 $55 $56 Register Description Message Buffer 2 Data Register Message Buffer 2 Data Register Message Buffer 2 Data Register Message Buffer 2 Data Register Reserved FC2MB3_CONTROL FC2MB3_ID_HIGH FC2MB3_ID_LOW FC2MB3_DATA FC2MB3_DATA FC2MB3_DATA FC2MB3_DATA $58 $59 $5A $5B $5C $5D $5E Message Buffer 3 Control / Status Register Message Buffer 3 ID High Register Message Buffer 3 ID Low Register Message Buffer 3 Data Register Message Buffer 3 Data Register Message Buffer 3 Data Register Message Buffer 3 Data Register Reserved FC2MB4_CONTROL FC2MB4_ID_HIGH FC2MB4_ID_LOW FC2MB4_DATA FC2MB4_DATA FC2MB4_DATA FC2MB4_DATA $60 $61 $62 $63 $64 $65 $66 Message Buffer 4 Control / Status Register Message Buffer 4 ID High Register Message Buffer 4 ID Low Register Message Buffer 4 Data Register Message Buffer 4 Data Register Message Buffer 4 Data Register Message Buffer 4 Data Register Reserved FC2MB5_CONTROL FC2MB5_ID_HIGH FC2MB5_ID_LOW FC2MB5_DATA FC2MB5_DATA FC2MB5_DATA FC2MB5_DATA $68 $69 $6A $6B $6C $6D $6E Message Buffer 5 Control / Status Register Message Buffer 5 ID High Register Message Buffer 5 ID Low Register Message Buffer 5 Data Register Message Buffer 5 Data Register Message Buffer 5 Data Register Message Buffer 5 Data Register Reserved FC2MB6_CONTROL FC2MB6_ID_HIGH FC2MB6_ID_LOW $70 $71 $72 Message Buffer 6 Control / Status Register Message Buffer 6 ID High Register Message Buffer 6 ID Low Register 56F8367 Technical Data, Rev. 3.0 76 Freescale Semiconductor Preliminary Peripheral Memory Mapped Registers Table 4-39 FlexCAN2 Registers Address Map (Continued) (FC2_BASE = $00 FA00) FlexCAN2 is NOT available in the 56F8167 device Register Acronym FC2MB6_DATA FC2MB6_DATA FC2MB6_DATA FC2MB6_DATA Address Offset $73 $74 $75 $76 Register Description Message Buffer 6 Data Register Message Buffer 6 Data Register Message Buffer 6 Data Register Message Buffer 6 Data Register Reserved FC2MB7_CONTROL FC2MB7_ID_HIGH FC2MB7_ID_LOW FC2MB7_DATA FC2MB7_DATA FC2MB7_DATA FC2MB7_DATA $78 $79 $7A $7B $7C $7D $7E Message Buffer 7 Control / Status Register Message Buffer 7 ID High Register Message Buffer 7 ID Low Register Message Buffer 7 Data Register Message Buffer 7 Data Register Message Buffer 7 Data Register Message Buffer 7 Data Register Reserved FC2MB8_CONTROL FC2MB8_ID_HIGH FC2MB8_ID_LOW FC2MB8_DATA FC2MB8_DATA FC2MB8_DATA FC2MB8_DATA $80 $81 $82 $83 $84 $85 $86 Message Buffer 8 Contro l /Status Register Message Buffer 8 ID High Register Message Buffer 8 ID Low Register Message Buffer 8 Data Register Message Buffer 8 Data Register Message Buffer 8 Data Register Message Buffer 8 Data Register Reserved FC2MB9_CONTROL FC2MB9_ID_HIGH FC2MB9_ID_LOW FC2MB9_DATA FC2MB9_DATA FC2MB9_DATA FC2MB9_DATA $88 $89 $8A $8B $8C $8D $8E Message Buffer 9 Control / Status Register Message Buffer 9 ID High Register Message Buffer 9 ID Low Register Message Buffer 9 Data Register Message Buffer 9 Data Register Message Buffer 9 Data Register Message Buffer 9 Data Register Reserved FC2MB10_CONTROL FC2MB10_ID_HIGH FC2MB10_ID_LOW $90 $91 $92 Message Buffer 10 Control / Status Register Message Buffer 10 ID High Register Message Buffer 10 ID Low Register 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 77 Table 4-39 FlexCAN2 Registers Address Map (Continued) (FC2_BASE = $00 FA00) FlexCAN2 is NOT available in the 56F8167 device Register Acronym FC2MB10_DATA FC2MB10_DATA FC2MB10_DATA FC2MB10_DATA Address Offset $93 $94 $95 $96 Register Description Message Buffer 10 Data Register Message Buffer 10 Data Register Message Buffer 10 Data Register Message Buffer 10 Data Register Reserved FC2MB11_CONTROL FC2MB11_ID_HIGH FC2MB11_ID_LOW FC2MB11_DATA FC2MB11_DATA FC2MB11_DATA FC2MB11_DATA $98 $99 $9A $9B $9C $9D $9E Message Buffer 11 Control / Status Register Message Buffer 11 ID High Register Message Buffer 11 ID Low Register Message Buffer 11 Data Register Message Buffer 11 Data Register Message Buffer 11 Data Register Message Buffer 11 Data Register Reserved FC2MB12_CONTROL FC2MB12_ID_HIGH FC2MB12_ID_LOW FC2MB12_DATA FC2MB12_DATA FC2MB12_DATA FC2MB12_DATA $A0 $A1 $A2 $A3 $A4 $A5 $A6 Message Buffer 12 Control / Status Register Message Buffer 12 ID High Register Message Buffer 12 ID Low Register Message Buffer 12 Data Register Message Buffer 12 Data Register Message Buffer 12 Data Register Message Buffer 12 Data Register Reserved FC2MB13_CONTROL FC2MB13_ID_HIGH FC2MB13_ID_LOW FC2MB13_DATA FC2MB13_DATA FC2MB13_DATA FC2MB13_DATA $A8 $A9 $AA $AB $AC $AD $AE Message Buffer 13 Control / Status Register Message Buffer 13 ID High Register Message Buffer 13 ID Low Register Message Buffer 13 Data Register Message Buffer 13 Data Register Message Buffer 13 Data Register Message Buffer 13 Data Register Reserved FC2MB14_CONTROL FC2MB14_ID_HIGH FC2MB14_ID_LOW $B0 $B1 $B2 Message Buffer 14 Control / Status Register Message Buffer 14 ID High Register Message Buffer 14 ID Low Register 56F8367 Technical Data, Rev. 3.0 78 Freescale Semiconductor Preliminary Factory Programmed Memory Table 4-39 FlexCAN2 Registers Address Map (Continued) (FC2_BASE = $00 FA00) FlexCAN2 is NOT available in the 56F8167 device Register Acronym FC2MB14_DATA FC2MB14_DATA FC2MB14_DATA FC2MB14_DATA Address Offset $B3 $B4 $B5 $B6 Register Description Message Buffer 14 Data Register Message Buffer 14 Data Register Message Buffer 14 Data Register Message Buffer 14 Data Register Reserved FC2MB15_CONTROL FC2MB15_ID_HIGH FC2MB15_ID_LOW FC2MB15_DATA FC2MB15_DATA FC2MB15_DATA FC2MB15_DATA $B8 $B9 $BA $BB $BC $BD $BE Message Buffer 15 Control / Status Register Message Buffer 15 ID High Register Message Buffer 15 ID Low Register Message Buffer 15 Data Register Message Buffer 15 Data Register Message Buffer 15 Data Register Message Buffer 15 Data Register Reserved 4.8 Factory Programmed Memory The Boot Flash memory block is programmed during manufacturing with a default Serial Bootloader program. The Serial Bootloader application can be used to load a user application into the Program and Data Flash (NOT available in the 56F8167 device) memories of the device. The 56F83xx SCI/CAN Bootloader User Manual (MC56F83xxBLUM) provides detailed information on this firmware. An application note, Production Flash Programming (AN1973), details how the Serial Bootloader program can be used to perform production Flash programming of the on-board Flash memories as well as other potential methods. Like all the Flash memory blocks, the Boot Flash can be erased and programmed by the user. The Serial Bootloader application is programmed as an aid to the end user, but is not required to be used or maintained in the Boot Flash memory. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 79 Part 5 Interrupt Controller (ITCN) 5.1 Introduction The Interrupt Controller (ITCN) module is used to arbitrate between various interrupt requests (IRQs), to signal to the 56800E core when an interrupt of sufficient priority exists, and what address to jump in order to service this interrupt. 5.2 Features The ITCN module design includes these distinctive features: * * * * Programmable priority levels for each IRQ Two programmable Fast Interrupts Notification to SIM module to restart clocks out of Wait and Stop modes Drives initial address on the address bus after reset For further information, see Table 4-5, Interrupt Vector Table Contents. 5.3 Functional Description The Interrupt Controller is a slave on the IPBus. It contains registers allowing each of the 86 interrupt sources to be set to one of four priority levels, excluding certain interrupts of fixed priority. Next, all of the interrupt requests of a given level are priority encoded to determine the lowest numerical value of the active interrupt requests for that level. Within a given priority level, 0 is the highest priority, while number 85 is the lowest. 5.3.1 Normal Interrupt Handling Once the ITCN has determined that an interrupt is to be serviced and which interrupt has the highest priority, an interrupt vector address is generated. Normal interrupt handling concatenates the VBA and the vector number to determine the vector address. In this way, an offset is generated into the vector table for each interrupt. 5.3.2 Interrupt Nesting Interrupt exceptions may be nested to allow an IRQ of higher priority than the current exception to be serviced. The following tables define the nesting requirements for each priority level. Table 5-1 Interrupt Mask Bit Definition SR[9]1 0 0 1 1 SR[8]1 0 1 0 1 Permitted Exceptions Priorities 0, 1, 2, 3 Priorities 1, 2, 3 Priorities 2, 3 Priority 3 Masked Exceptions None Priority 0 Priorities 0, 1 Priorities 0, 1, 2 1. Core status register bits indicating current interrupt mask within the core. 56F8367 Technical Data, Rev. 3.0 80 Freescale Semiconductor Preliminary Functional Description Table 5-2. Interrupt Priority Encoding IPIC_LEVEL[1:0]1 00 01 01 11 Current Interrupt Priority Level No Interrupt or SWILP Priority 0 Priority 1 Priorities 2 or 3 Required Nested Exception Priority Priorities 0, 1, 2, 3 Priorities 1, 2, 3 Priorities 2, 3 Priority 3 1. See IPIC field definition in Part 5.6.30.2 5.3.3 Fast Interrupt Handling Fast interrupts are described in the DSP56800E Reference Manual. The interrupt controller recognizes fast interrupts before the core does. A fast interrupt is defined (to the ITCN) by: 1. Setting the priority of the interrupt as level 2, with the appropriate field in the IPR registers 2. Setting the FIMn register to the appropriate vector number 3. Setting the FIVALn and FIVAHn registers with the address of the code for the fast interrupt When an interrupt occurs, its vector number is compared with the FIM0 and FIM1 register values. If a match occurs, and it is a level 2 interrupt, the ITCN handles it as a fast interrupt. The ITCN takes the vector address from the appropriate FIVALn and FIVAHn registers, instead of generating an address that is an offset from the VBA. The core then fetches the instruction from the indicated vector adddress and if it is not a JSR, the core starts its fast interrupt handling. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 81 5.4 Block Diagram Priority Level any0 Level 0 82->7 Priority Encoder 7 INT1 2->4 Decode INT VAB CONTROL IPIC any3 Level 3 Priority Level 82->7 Priority Encoder IACK SR[9:8] PIC_EN INT82 2->4 Decode 7 Figure 5-1 Interrupt Controller Block Diagram 5.5 Operating Modes The ITCN module design contains two major modes of operation: * * Functional Mode The ITCN is in this mode by default. Wait and Stop Modes During Wait and Stop modes, the system clocks and the 56800E core are turned off. The ITCN will signal a pending IRQ to the System Integration Module (SIM) to restart the clocks and service the IRQ. An IRQ can only wake up the core if the IRQ is enabled prior to entering the Wait or Stop mode. Also, the IRQA and IRQB signals automatically become low-level sensitive in these modes even if the control register bits are set to make them falling-edge sensitive. This is because there is no clock available to detect the falling edge. A peripheral which requires a clock to generate interrupts will not be able to generate interrupts during Stop mode. The FlexCAN module can wake the device from Stop mode, and a reset will do just that, or IRQA and IRQB can wake it up. 56F8367 Technical Data, Rev. 3.0 82 Freescale Semiconductor Preliminary Register Descriptions 5.6 Register Descriptions A register address is the sum of a base address and an address offset. The base address is defined at the system level and the address offset is defined at the module level. The ITCN peripheral has 24 registers. Table 5-3 ITCN Register Summary (ITCN_BASE = $00F1A0) Register Acronym IPR0 IPR1 IPR2 IPR3 IPR4 IPR5 IPR6 IPR7 IPR8 IPR9 VBA FIM0 FIVAL0 FIVAH0 FIM1 FIVAL1 FIVAH1 IRQP0 IRQP1 IRQP2 IRQP3 IRQP4 IRQP5 Base Address + $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F $10 $11 $12 $13 $14 $15 $16 Register Name Interrupt Priority Register 0 Interrupt Priority Register 1 Interrupt Priority Register 2 Interrupt Priority Register 3 Interrupt Priority Register 4 Interrupt Priority Register 5 Interrupt Priority Register 6 Interrupt Priority Register 7 Interrupt Priority Register 8 Interrupt Priority Register 9 Vector Base Address Register Fast Interrupt 0 Match Register Fast Interrupt 0 Vector Address Low Register Fast Interrupt 0 Vector Address High Register Fast Interrupt 1 Match Register Fast Interrupt 1 Vector Address Low Register Fast Interrupt 1 Vector Address High Register IRQ Pending Register 0 IRQ Pending Register 1 IRQ Pending Register 2 IRQ Pending Register 3 IRQ Pending Register 4 IRQ Pending Register 5 Reserved ICTL $1D Interrupt Control Register Reserved IPR10 $1F Interrupt Priority Register 10 5.6.32 5.6.30 Section Location 5.6.1 5.6.2 5.6.3 5.6.4 5.6.5 5.6.6 5.6.7 5.6.8 5.6.9 5.6.10 5.6.11 5.6.12 5.6.13 5.6.14 5.6.15 5.6.16 5.6.17 5.6.18 5.6.19 5.6.20 5.6.21 5.6.22 5.6.23 Note: The IPR10 is NOT available in the 56F8167 device. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 83 Add. Register Offset Name $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F IPR0 IPR1 IPR2 IPR3 IPR4 IPR5 IPR6 IPR7 IPR8 IPR9 R W R W R W R 15 0 0 14 0 0 13 12 11 10 9 0 0 8 0 0 7 0 0 6 0 0 5 0 4 0 3 0 2 0 1 0 0 0 BKPT_U0 IPL 0 0 STPCNT IPL 0 0 RX_REG IPL 0 0 TX_REG IPL IRQB IPL FCBOFF IPL GPIOB IPL SCI1_XMIT IPL TRBUF IPL IRQA IPL 0 0 FMCBE IPL GPIOD FMCC IPL GPIOE IPL SPI1_XMIT IPL FMERR IPL GPIOF IPL SPI1_RCV IPL SCI1_RCV IPL TMRD2 IPL TMRB2 IPL 0 0 LOCK IPL FCMSGBUF IPL 0 0 LVI IPL FCWKUP IPL 0 0 0 0 IPL W R SPI0_RCV IPL W FCERR IPL GPIOA IPL SCI1_TIDL IPL 0 0 GPIOC IPL SPI0_XMIT IPL R W R W R W DEC1_XIRQ IPL DEC1_HIRQ IPL TMRC0 IPL TMRA0 IPL TMRD3 IPL TMRB3 IPL SCI1_RERR IPL TMRD1 IPL TMRB1 IPL SCI0_TIDL IPL PWMB_RL IPL TMRD0 IPL TMRB0 IPL SCI0_XMIT IPL ADCA_ZC IPL DEC0_XIRQ IPL DEC0_HIRQ IPL TMRC2 IPL TMRA2 IPL ADCA_CC IPL TMRC1 IPL TMRA1 IPL ADCB_CC IPL TMRC3 IPL TMRA3 IPL ABCB_ZC IPL R SCI0_RCV IPL SCI0_RERR IPL W R PWMA F IPL PWMB F IPL W 0 0 0 0 0 0 0 PWMA_RL IPL R VBA W R VBA0 W R FIVAL0 W R FIVAH0 W R FIM1 W R FIVAL1 W VECTOR BASE ADDRESS 0 0 0 0 0 FAST INTERRUPT 0 FAST INTERRUPT 0 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 FAST INTERRUPT 0 VECTOR ADDRESS HIGH FAST INTERRUPT 1 FAST INTERRUPT 1 VECTOR ADDRESS LOW Figure 5-2 ITCN Register Map Summary 56F8367 Technical Data, Rev. 3.0 84 Freescale Semiconductor Preliminary Register Descriptions Add. Register Offset Name $10 $11 $12 $13 $14 $15 FIVAH1 IRQP0 IRQP1 IRQP2 IRQP3 IRQP4 R W R W R W R W R W R W R W Reserved $1D ICTL Reserved $1F IPR10 R W R W 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 3 2 1 0 FAST INTERRUPT 1 VECTOR ADDRESS HIGH 1 PENDING [16:2] PENDING [32:17] PENDING [48:33] PENDING [64:49] PENDING [80:65] $16 IRQP5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PENDING [81] INT IPIC VAB INT_DIS 1 IRQB IRQA STATE STATE IRQB EDG IRQA EDG 0 0 0 0 0 0 0 0 FLEXCAN2 MSGBUG IPL FLEXCAN2 WKUP IPL FLEXCAN2 ERR IPL FLEXCAN2 BOFF IPL = Reserved Figure 5-2 ITCN Register Map Summary 5.6.1 Interrupt Priority Register 0 (IPR0) 15 0 Base + $0 Read Write RESET 14 0 13 12 11 10 9 0 8 0 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 0 BKPT_U0IPL 0 0 0 0 STPCNT IPL 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-3 Interrupt Priority Register 0 (IPR0) 5.6.1.1 5.6.1.2 Reserved--Bits 15-14 EOnCE Breakpoint Unit 0 Interrupt Priority Level (BKPT_U0 IPL)-- Bits13-12 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority levels for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 85 * 11 = IRQ is priority level 3 5.6.1.3 EOnCE Step Counter Interrupt Priority Level (STPCNT IPL)-- Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.1.4 Reserved--Bits 9-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 5.6.2 Interrupt Priority Register 1 (IPR1) Base + $1 Read Write RESET 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 4 3 2 1 0 RX_REG IPL TX_REG IPL TRBUF IPL Figure 5-4 Interrupt Priority Register 1 (IPR1) 5.6.2.1 5.6.2.2 Reserved--Bits 15-6 EOnCE Receive Register Full Interrupt Priority Level (RX_REG IPL)--Bits 5-4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.2.3 EOnCE Transmit Register Empty Interrupt Priority Level (TX_REG IPL)--Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 56F8367 Technical Data, Rev. 3.0 86 Freescale Semiconductor Preliminary Register Descriptions 5.6.2.4 EOnCE Trace Buffer Interrupt Priority Level (TRBUF IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 1 10 = IRQ is priority level 2 11 = IRQ is priority level 3 5.6.3 Interrupt Priority Register 2 (IPR2) 15 14 13 12 11 10 9 8 7 6 5 0 FMCBE IPL 0 0 FMCC IPL 0 0 FMERR IPL 0 0 LOCK IPL 0 0 LVI IPL 0 0 0 0 Base + $2 Read Write RESET 4 0 3 2 1 0 IRQB IPL 0 0 IRQA IPL 0 0 Figure 5-5 Interrupt Priority Register 2 (IPR2) 5.6.3.1 Flash Memory Command, Data, Address Buffers Empty Interrupt Priority Level (FMCBE IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.2 Flash Memory Command Complete Priority Level (FMCC IPL)-- Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.3 Flash Memory Error Interrupt Priority Level (FMERR IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 87 5.6.3.4 PLL Loss of Lock Interrupt Priority Level (LOCK IPL)--Bits 9-8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.5 Low Voltage Detector Interrupt Priority Level (LVI IPL)--Bits 7-6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.6 5.6.3.7 Reserved--Bits 5-4 External IRQ B Interrupt Priority Level (IRQB IPL)--Bits 3-2 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.3.8 External IRQ A Interrupt Priority Level (IRQA IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. It is disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4 Interrupt Priority Register 3 (IPR3) Base + $3 Read GPIOD IPL GPIOE IPL GPIOFIPL FCMSGBUF IPL 0 0 FCWKUP IPL 0 0 FCERR IPL 0 0 FCBOFF IPL 0 0 0 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 Write RESET 0 0 0 0 0 0 Figure 5-6 Interrupt Priority Register 3 (IPR3) 56F8367 Technical Data, Rev. 3.0 88 Freescale Semiconductor Preliminary Register Descriptions 5.6.4.1 GPIOD Interrupt Priority Level (GPIOD IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.2 GPIOE Interrupt Priority Level (GPIOE IPL)--Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.3 GPIOF Interrupt Priority Level (GPIOF IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.4 FlexCAN Message Buffer Interrupt Priority Level (FCMSGBUF IPL)-- Bits 9-8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.5 FlexCAN Wake Up Interrupt Priority Level (FCWKUP IPL)--Bits 7-6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 89 5.6.4.6 FlexCAN Error Interrupt Priority Level (FCERR IPL)-- Bits 5-4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.7 FlexCAN Bus Off Interrupt Priority Level (FCBOFF IPL)-- Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.4.8 Reserved--Bits 1-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 5.6.5 Interrupt Priority Register 4 (IPR4) 15 14 13 12 11 10 9 0 Base + $4 Read Write RESET 8 0 7 0 6 0 5 4 3 2 1 0 SPI0_RCV IPL 0 0 SPI1_XMIT IPL 0 0 SPI1_RCV IPL 0 0 GPIOA IPL 0 0 0 0 0 0 GPIOB IPL 0 0 GPIOC IPL 0 0 Figure 5-7 Interrupt Priority Register 4 (IPR4) 5.6.5.1 SPI0 Receiver Full Interrupt Priority Level (SPI0_RCV IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.2 SPI1 Transmit Empty Interrupt Priority Level (SPI1_XMIT IPL)-- Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 56F8367 Technical Data, Rev. 3.0 90 Freescale Semiconductor Preliminary Register Descriptions * * 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.3 SPI1 Receiver Full Interrupt Priority Level (SPI1_RCV IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.4 5.6.5.5 Reserved--Bits 9-6 GPIOA Interrupt Priority Level (GPIOA IPL)--Bits 5-4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.6 GPIOB Interrupt Priority Level (GPIOB IPL)--Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.5.7 GPIOC Interrupt Priority Level (GPIOC IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 91 5.6.6 Interrupt Priority Register 5 (IPR5) 15 14 13 12 11 10 9 8 7 0 Base + $5 Read Write RESET 6 0 5 4 3 2 1 0 DEC1_XIRQ IPL 0 0 DEC1_HIRQ IPL 0 0 SCI1_RCV IPL 0 0 SCI1_RERR IPL 0 0 SCI1_TIDL IPL 0 0 SCI1_XMIT IPL 0 0 SPI0_XMIT IPL 0 0 0 0 Figure 5-8 Interrupt Priority Register 5 (IPR5) 5.6.6.1 Quadrature Decoder 1 INDEX Pulse Interrupt Priority Level (DEC1_XIRQ IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.2 Quadrature Decoder 1 HOME Signal Transition or Watchdog Timer Interrupt Priority Level (DEC1_HIRQ IPL)--Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.3 SCI1 Receiver Full Interrupt Priority Level (SCI1_RCV IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.4 SCI1 Receiver Error Interrupt Priority Level (SCI1_RERR IPL)--Bits 9-8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 92 Freescale Semiconductor Preliminary Register Descriptions 5.6.6.5 5.6.6.6 Reserved--Bits 7-6 SCI1 Transmitter Idle Interrupt Priority Level (SCI1_TIDL IPL)--Bits 5-4 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.7 SCI1 Transmitter Empty Interrupt Priority Level (SCI1_XMIT IPL)-- Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.6.8 SPI0 Transmitter Empty Interrupt Priority Level (SPI_XMIT IPL)-- Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7 Interrupt Priority Register 6 (IPR6) 15 14 13 12 11 10 9 8 7 6 5 0 TMRC0 IPL 0 0 TMRD3 IPL 0 0 TMRD2 IPL 0 0 TMRD1 IPL 0 0 TMRD0 IPL 0 0 0 0 Base + $6 Read Write RESET 4 0 3 2 1 0 DEC0_XIRQ IPL 0 0 DEC0_HIRQ IPL 0 0 Figure 5-9 Interrupt Priority Register 6 (IPR6) 5.6.7.1 Timer C, Channel 0 Interrupt Priority Level (TMRC0 IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * 00 = IRQ disabled (default) 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 93 * * * 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.2 Timer D, Channel 3 Interrupt Priority Level (TMRD3 IPL)--Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.3 Timer D, Channel 2 Interrupt Priority Level (TMRD2 IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.4 Timer D, Channel 1 Interrupt Priority Level (TMRD1 IPL)--Bits 9-8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.5 Timer D, Channel 0 Interrupt Priority Level (TMRD0 IPL)--Bits 7-6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.6 5.6.7.7 Reserved--Bits 5-4 Quadrature Decoder 0, INDEX Pulse Interrupt Priority Level (DEC0_XIRQ IPL)--Bits 3-2 56F8367 Technical Data, Rev. 3.0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. 94 Freescale Semiconductor Preliminary Register Descriptions They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.7.8 Quadrature Decoder 0, HOME Signal Transition or Watchdog Timer Interrupt Priority Level (DEC0_HIRQ IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8 Interrupt Priority Register 7 (IPR7) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read TMRA0 IPL TMRB3 IPL 0 0 TMRB2 IPL 0 0 TMRB1 IPL 0 0 TMRB0 IPL 0 0 TMRC3 IPL 0 0 TMRC2 IPL 0 0 TMRC1 IPL 0 0 Base + $7 Write RESET 0 0 Figure 5-10 Interrupt Priority Register (IPR7) 5.6.8.1 Timer A, Channel 0 Interrupt Priority Level (TMRA0 IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.2 Timer B, Channel 3 Interrupt Priority Level (TMRB3 IPL)--Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 95 5.6.8.3 Timer B, Channel 2 Interrupt Priority Level (TMRB2 IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.4 Timer B, Channel 1 Interrupt Priority Level (TMRB1 IPL)--Bits 9-8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.5 Timer B, Channel 0 Interrupt Priority Level (TMRB0 IPL)--Bits 7-6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.6 Timer C, Channel 3 Interrupt Priority Level (TMRC3 IPL)--Bits 5-4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.8.7 Timer C, Channel 2 Interrupt Priority Level (TMRC2 IPL)--Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 96 Freescale Semiconductor Preliminary Register Descriptions 5.6.8.8 Timer C, Channel 1 Interrupt Priority Level (TMRC1 IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9 Interrupt Priority Register 8 (IPR8) 15 14 13 12 11 0 Base + $8 Read Write RESET 10 0 9 8 7 6 5 4 3 2 1 0 SCI0_RCV IPL 0 0 SCI0_RERR IPL 0 0 SCI0_TIDL IPL 0 0 SCI0_XMIT IPL 0 0 TMRA3 IPL 0 0 TMRA2 IPL 0 0 TMRA1 IPL 0 0 0 0 Figure 5-11 Interrupt Priority Register 8 (IPR8) 5.6.9.1 SCI0 Receiver Full Interrupt Priority Level (SCI0_RCV IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.2 SCI0 Receiver Error Interrupt Priority Level (SCI0_RERR IPL)-- Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.3 5.6.9.4 Reserved--Bits 11-10 SCI0 Transmitter Idle Interrupt Priority Level (SCI0_TIDL IPL)--Bits 9-8 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 97 * * 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.5 SCI0 Transmitter Empty Interrupt Priority Level (SCI0_XMIT IPL)-- Bits 7-6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.6 Timer A, Channel 3 Interrupt Priority Level (TMRA3 IPL)--Bits 5-4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.7 Timer A, Channel 2 Interrupt Priority Level (TMRA2 IPL)--Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.9.8 Timer A, Channel 1 Interrupt Priority Level (TMRA1 IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 98 Freescale Semiconductor Preliminary Register Descriptions 5.6.10 Interrupt Priority Register 9 (IPR9) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PWMA_F IPL 0 0 PWMB_F IPL 0 0 Base + $9 PWMA_RL IPL 0 0 PWM_RL IPL 0 0 ADCA_ZC IPL ABCB_ZC IPL 0 0 0 0 ADCA_CC IPL 0 0 ADCB_CC IPL 0 0 RESET Figure 5-12 Interrupt Priority Register 9 (IPR9) 5.6.10.1 PWM A Fault Interrupt Priority Level (PWMA_F IPL)--Bits 15-14 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.2 PWM B Fault Interrupt Priority Level (PWMB_F IPL)--Bits 13-12 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.3 Reload PWM A Interrupt Priority Level (PWMA_RL IPL)--Bits 11-10 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.4 Reload PWM B Interrupt Priority Level (PWMB_RL IPL)--Bits 9-8 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 99 5.6.10.5 ADC A Zero Crossing or Limit Error Interrupt Priority Level (ADCA_ZC IPL)--Bits 7-6 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 0. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.6 ADC B Zero Crossing or Limit Error Interrupt Priority Level (ADCB_ZC IPL)--Bits 5-4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.7 ADC A Conversion Complete Interrupt Priority Level (ADCA_CC IPL)--Bits 3-2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.10.8 ADC B Conversion Complete Interrupt Priority Level (ADCB_CC IPL)--Bits 1-0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 56F8367 Technical Data, Rev. 3.0 100 Freescale Semiconductor Preliminary Register Descriptions 5.6.11 Vector Base Address Register (VBA) 15 0 Base + $A Read Write RESET 14 0 13 0 12 11 10 9 8 7 6 5 4 3 2 1 0 VECTOR BASE ADDRESS 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-13 Vector Base Address Register (VBA) 5.6.11.1 5.6.11.2 Reserved--Bits 15-13 Interrupt Vector Base Address (VECTOR BASE ADDRESS)-- Bits 12-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. The contents of this register determine the location of the Vector Address Table. The value in this register is used as the upper 13 bits of the interrupt Vector Address Bus (VAB[20:0]). The lower eight bits are determined based upon the highest-priority interrupt. They are then appended onto VBA before presenting the full VAB to the 56800E core; see Part 5.3.1 for details. 5.6.12 Fast Interrupt 0 Match Register (FIM0) 15 0 Base + $B Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 5 4 3 2 1 0 FAST INTERRUPT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-14 Fast Interrupt 0 Match Register (FIM0) 5.6.12.1 5.6.12.2 Reserved--Bits 15-7 Fast Interrupt 0 Vector Number (FAST INTERRUPT 0)--Bits 6-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This value determines which IRQ will be a Fast Interrupt 0. Fast interrupts vector directly to a service routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table first; see Part 5.3.3. IRQs used as fast interrupts must be set to priority level 2. Unexpected results will occur if a fast interrupt vector is set to any other priority. Fast interrupts automatically become the highest-priority level 2 interrupt, regardless of their location in the interrupt table, prior to being declared as fast interrupt. Fast interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each IRQ, refer to Table 4-5. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 101 5.6.13 Fast Interrupt 0 Vector Address Low Register (FIVAL0) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write FAST INTERRUPT 0 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Base + $C RESET Figure 5-15 Fast Interrupt 0 Vector Address Low Register (FIVAL0) 5.6.13.1 Fast Interrupt 0 Vector Address Low (FIVAL0)--Bits 15-0 The lower 16 bits of the vector address are used for Fast Interrupt 0. This register is combined with FIVAH0 to form the 21-bit vector address for Fast Interrupt 0 defined in the FIM0 register. 5.6.14 Fast Interrupt 0 Vector Address High Register (FIVAH0) 15 0 Base + $D Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 3 2 1 0 FAST INTERRUPT 0 VECTOR ADDRESS HIGH 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-16 Fast Interrupt 0 Vector Address High Register (FIVAH0) 5.6.14.1 5.6.14.2 Reserved--Bits 15-5 Fast Interrupt 0 Vector Address High (FIVAH0)--Bits 4-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. The upper five bits of the vector address are used for Fast Interrupt 0. This register is combined with FIVAL0 to form the 21-bit vector address for Fast Interrupt 0 defined in the FIM0 register. 5.6.15 Fast Interrupt 1 Match Register (FIM1) 15 0 Base + $E Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 5 4 3 2 1 0 FAST INTERRUPT 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-17 Fast Interrupt 1 Match Register (FIM1) 5.6.15.1 5.6.15.2 Reserved--Bits 15-7 Fast Interrupt 1 Vector Number (FAST INTERRUPT 1)--Bits 6-0 This bit field is reserved or not implemented. It is read as 0, but cannot be modified by writing. This value determines which IRQ will be a Fast Interrupt 1. Fast interrupts vector directly to a service routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table first; see Part 5.3.3. IRQs used as fast interrupts must be set to priority level 2. Unexpected results will occur if a fast interrupt vector is set to any other priority. Fast interrupts automatically become the 56F8367 Technical Data, Rev. 3.0 102 Freescale Semiconductor Preliminary Register Descriptions highest-priority level 2 interrupt, regardless of their location in the interrupt table, prior to being declared as fast interrupt. Fast interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each IRQ, refer to Table 4-5. 5.6.16 Fast Interrupt 1 Vector Address Low Register (FIVAL1) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write Base + $F FAST INTERRUPT 1 VECTOR ADDRESS LOW 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RESET Figure 5-18 Fast Interrupt 1 Vector Address Low Register (FIVAL1) 5.6.16.1 Fast Interrupt 1 Vector Address Low (FIVAL1)--Bits 15-0 The lower 16 bits of vector address are used for Fast Interrupt 1. This register is combined with FIVAH1 to form the 21-bit vector address for Fast Interrupt 1 defined in the FIM1 register. 5.6.17 Fast Interrupt 1 Vector Address High Register (FIVAH1) 15 0 Base + $10 Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 3 2 1 0 FAST INTERRUPT 1 VECTOR ADDRESS HIGH 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 5-19 Fast Interrupt 1 Vector Address High Register (FIVAH1) 5.6.17.1 5.6.17.2 Reserved--Bits 15-5 Fast Interrupt 1 Vector Address High (FIVAH1)--Bits 4-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. The upper five bits of vector address are used for Fast Interrupt 1. This register is combined with FIVAL1 to form the 21-bit vector address for Fast Interrupt 1 defined in the FIM1 register. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 103 5.6.18 IRQ Pending 0 Register (IRQP0) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 Base + $11 Read Write RESET PENDING [16:2] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-20 IRQ Pending 0 Register (IRQP0) 5.6.18.1 IRQ Pending (PENDING)--Bits 16-2 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. * * 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.18.2 Reserved--Bit 0 This bit is reserved or not implemented. It is read as 1 and cannot be modified by writing. 5.6.19 IRQ Pending 1 Register (IRQP1) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [32:17] $Base + $12 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-21 IRQ Pending 1 Register (IRQP1) 5.6.19.1 IRQ Pending (PENDING)--Bits 32-17 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. * * 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.20 IRQ Pending 2 Register (IRQP2) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [48:33] Base + $13 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-22 IRQ Pending 2 Register (IRQP2) 5.6.20.1 IRQ Pending (PENDING)--Bits 48-33 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. 56F8367 Technical Data, Rev. 3.0 104 Freescale Semiconductor Preliminary Register Descriptions * * 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.21 IRQ Pending 3 Register (IRQP3) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [64:49] Base + $14 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-23 IRQ Pending 3 Register (IRQP3) 5.6.21.1 IRQ Pending (PENDING)--Bits 64-49 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. * * 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.22 IRQ Pending 4 Register (IRQP4) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read Write PENDING [80:65] Base + $15 RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-24 IRQ Pending 4 Register (IRQP4) 5.6.22.1 IRQ Pending (PENDING)--Bits 80-65 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 81. * * 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.23 IRQ Pending 5 Register (IRQP5) 15 1 Base + $16 Read Write RESET 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1 6 1 5 1 4 3 2 1 0 PENDING[85:81] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 5-25 IRQ Pending Register 5 (IRQP5) 5.6.23.1 Reserved--Bits 96-86 This bit field is reserved or not implemented. The bits are read as 1 and cannot be modified by writing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 105 5.6.23.2 IRQ Pending (PENDING)--Bits 81-85 This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2 through 85. * * 0 = IRQ pending for this vector number 1 = No IRQ pending for this vector number 5.6.24 5.6.25 5.6.26 5.6.27 5.6.28 5.6.29 5.6.30 Reserved--Base + 17 Reserved--Base + 18 Reserved--Base + 19 Reserved--Base + 1A Reserved--Base + 1B Reserved--Base + 1C ITCN Control Register (ICTL) 15 INT Base + $1D Read Write RESET 14 IPIC 13 12 11 10 9 VAB 8 7 6 5 INT_DIS 4 1 3 IRQB STATE 2 IRQA STATE 1 IRQB EDG 0 0 IRQA EDG 0 0 0 0 1 0 0 0 0 0 0 0 1 1 1 Figure 5-26 ITCN Control Register (ICTL) 5.6.30.1 * * Interrupt (INT)--Bit 15 This read-only bit reflects the state of the interrupt to the 56800E core. 0 = No interrupt is being sent to the 56800E core 1 = An interrupt is being sent to the 56800E core 5.6.30.2 Interrupt Priority Level (IPIC)--Bits 14-13 These read-only bits reflect the state of the new interrupt priority level bits being presented to the 56800E core at the time the last IRQ was taken. This field is only updated when the 56800E core jumps to a new interrupt service routine. Note: * * * * Nested interrupts may cause this field to be updated before the original interrupt service routine can read it. 00 = Required nested exception priority levels are 0, 1, 2, or 3 01 = Required nested exception priority levels are 1, 2, or 3 10 = Required nested exception priority levels are 2 or 3 11 = Required nested exception priority level is 3 56F8367 Technical Data, Rev. 3.0 106 Freescale Semiconductor Preliminary Register Descriptions 5.6.30.3 Vector Number - Vector Address Bus (VAB)--Bits 12-6 This read-only field shows the vector number (VAB[7:1]) used at the time the last IRQ was taken. This field is only updated when the 56800E core jumps to a new interrupt service routine. Note: Nested interrupts may cause this field to be updated before the original interrupt service routine can read it. 5.6.30.4 * * Interrupt Disable (INT_DIS)--Bit 5 This bit allows all interrupts to be disabled. 0 = Normal operation (default) 1 = All interrupts disabled 5.6.30.5 5.6.30.6 5.6.30.7 5.6.30.8 Reserved--Bit 4 IRQB State Pin (IRQB STATE)--Bit 3 IRQA State Pin (IRQA STATE)--Bit 2 IRQB Edge Pin (IRQB Edg)--Bit 1 This bit field is reserved or not implemented. It is read as 1 and cannot be modified by writing. This read-only bit reflects the state of the external IRQB pin. This read-only bit reflects the state of the external IRQA pin. This bit controls whether the external IRQB interrupt is edge- or level-sensitive. During Stop and Wait modes, it is automatically level-sensitive. * * 0 = IRQB interrupt is a low-level sensitive (default) 1 = IRQB interrupt is falling-edge sensitive 5.6.30.9 IRQA Edge Pin (IRQA Edg)--Bit 0 This bit controls whether the external IRQA interrupt is edge- or level-sensitive. During Stop and Wait modes, it is automatically level-sensitive. * * 0 = IRQA interrupt is a low-level sensitive (default) 1 = IRQA interrupt is falling-edge sensitive 5.6.31 5.6.32 Reserved--Base + $1E Interrupt Priority Register 10 (IPR10) 15 0 Base + $1F Read Write RESET 14 0 13 0 12 11 10 0 0 0 9 0 8 0 7 6 5 4 3 2 1 0 FLEXCAN2_ MSGBUF IPL 0 0 FLEXCAN2_ WKUP IPL 0 0 FLEXCAN2_ ERR IPL 0 0 FLEXCAN2_ BOFF IPL 0 0 0 0 0 1 0 0 0 0 Note: This register is NOT available in the 56F8167 device. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 107 5.6.32.1 5.6.32.2 Reserved--Bits 15 - 8 FlexCAN2 Message Buffer Interrupt Priority Level (FlexCAN2_MSGBUF IPL)--Bits 7 - 6 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.32.3 FlexCAN2 Wake Up Interrupt Priority Level (FlexCAN2_WKUP IPL)-- Bits 5 - 4 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.32.4 FlexCAN2 Error Interrupt Priority Level (FlexCAN2_ERR IPL)--Bits 3 - 2 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.6.32.5 FlexCAN2 Bus-Off Interrupt Priority Level (FlexCAN2_BOFF IPL)-- Bits 1 - 0 This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2. They are disabled by default. * * * * 00 = IRQ disabled (default) 01 = IRQ is priority level 0 10 = IRQ is priority level 1 11 = IRQ is priority level 2 5.7 Resets 5.7.1 Reset Handshake Timing 56F8367 Technical Data, Rev. 3.0 108 Freescale Semiconductor Preliminary The ITCN provides the 56800E core with a reset vector address whenever RESET is asserted. The reset Resets vector will be presented until the second rising clock edge after RESET is released. 5.7.2 ITCN After Reset After reset, all of the ITCN registers are in their default states. This means all interrupts are disabled, except the core IRQs with fixed priorities: * * * * * * * * Illegal Instruction SW Interrupt 3 HW Stack Overflow Misaligned Long Word Access SW Interrupt 2 SW Interrupt 1 SW Interrupt 0 SW Interrupt LP These interrupts are enabled at their fixed priority levels. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 109 Part 6 System Integration Module (SIM) 6.1 Overview The SIM module is a system catchall for the glue logic that ties together the system-on-chip. It controls distribution of resets and clocks and provides a number of control features. The system integration module is responsible for the following functions: * * * * * * * Reset sequencing Clock generation & distribution Stop/Wait control Pull-up Enables for Selected Peripherals System status registers Registers for software access to the JTAG ID of the chip Enforcing Flash security These are discussed in more detail in the sections that follow. 6.2 Features The SIM has the following features: * * * Flash security feature prevents unauthorized access to code/data contained in on-chip Flash memory Power-saving clock gating for peripheral Three power modes (Run, Wait, Stop) to control power utilization -- Stop mode shuts down 56800E core, system clock, peripheral clock, and PLL operation -- Stop mode entry can optionally disable PLL and Oscillator (low power vs. fast restart); must be done explicitly -- Wait mode shuts down the 56800E core, and unnecessary system clock operation -- Run mode supports full part operation * * * * * * * Controls to enable/disable the 56800E core WAIT and STOP instructions Calculates base delay for reset extension based upon POR or RESET operations. Reset delay will be either 3 x 32 clocks for reset, except for POR, which is 221 clock cycles. Controls reset sequencing after reset Software-initiated reset Four 16-bit registers reset only by a Power-On Reset usable for general purpose software control System Control Register Registers for software access to the JTAG ID of the chip 56F8367 Technical Data, Rev. 3.0 110 Freescale Semiconductor Preliminary Operating Modes 6.3 Operating Modes Since the SIM is responsible for distributing clocks and resets across the chip, it must understand the various chip operating modes and take appropriate action. These are: * Reset Mode, which has two submodes: -- POR and RESET operation The 56800E core and all peripherals are reset. This occurs when the internal POR is asserted or the RESET pin is asserted. -- COP reset and software reset operation The 56800E core and all peripherals are reset. The MA bit within the OMR is not changed. This allows the software to determine the boot mode (internal or external boot) to be used on the next reset. * * Run Mode This is the primary mode of operation for this device. In this mode, the 56800E controls chip operation Debug Mode The 56800E is controlled via JTAG/EOnCE when in debug mode. All peripherals, except the COP and PWMs, continue to run. COP is disabled and PWM outputs are optionally switched off to disable any motor from being driven; see the PWM chapter in the 56F8300 Peripheral User Manual for details. Wait Mode In Wait mode, the core clock and memory clocks are disabled. Optionally, the COP can be stopped. Similarly, it is an option to switch off PWM outputs to disable any motor from being driven. All other peripherals continue to run. Stop Mode When in Stop mode, the 56800E core, memory, and most peripheral clocks are shut down. Optionally, the COP and CAN can be stopped. For lowest power consumption in Stop mode, the PLL can be shut down. This must be done explicitly before entering Stop mode, since there is no automatic mechanism for this. The CAN (along with any non-gated interrupt) is capable of waking the chip up from Stop mode, but is not fully functional in Stop mode. * * 6.4 Operating Mode Register Bit Type RESET 15 NL R/W 0 0 0 0 0 0 0 14 13 12 11 10 9 8 CM R/W 0 7 XP R/W 0 6 SD R/W 0 5 R R/W 0 4 SA R/W 0 3 EX R/W 0 2 0 1 MB R/W 0 MA R/W X 0 X Figure 6-1 OMR The reset state for MB and MA will depend on the Flash secured state. See Part 4.2 and Part 7 for detailed information on how the Operating Mode Register (OMR) MA and MB bits operate in this device. For all other bits, see the DSP56800E Reference Manual. Note: The OMR is not a Memory Map register; it is directly accessible in code through the acronym OMR. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 111 6.5 Register Descriptions Table 6-1 SIM Registers (SIM_BASE = $00 F350) Address Offset Base + $0 Base + $1 Base + $2 Base + $3 Base + $4 Base + $5 Base + $6 Base + $7 Base + $8 Address Acronym SIM_CONTROL SIM_RSTSTS SIM_SCR0 SIM_SCR1 SIM_SCR2 SIM_SCR3 SIM_MSH_ID SIM_LSH_ID SIM_PUDR Register Name Control Register Reset Status Register Software Control Register 0 Software Control Register 1 Software Control Register 2 Software Control Register 3 Most Significant Half of JTAG ID Least Significant Half of JTAG ID Pull-up Disable Register Reserved Base + $A Base + $B Base + $C Base + $D Base + $E Base + $F SIM_CLKOSR SIM_GPS SIM_PCE SIM_ISALH SIM_ISALL SIM_PCE2 CLKO Select Register GPIO Peripheral Select Register Peripheral Clock Enable Register I/O Short Address Location High Register I/O Short Address Location Low Register Peripheral Clock Enable Register 2 6.5.7 6.5.8 6.5.9 6.5.10 6.5.10 6.5.11 Section Location 6.5.1 6.5.2 6.5.3 6.5.3 6.5.3 6.5.3 6.5.4 6.5.5 6.5.6 56F8367 Technical Data, Rev. 3.0 112 Freescale Semiconductor Preliminary Register Descriptions Add. Offset $0 $1 $2 $3 $4 $5 $6 $7 $8 Register Name SIM_ CONTROL SIM_ RSTSTS SIM_SCR0 SIM_SCR1 SIM_SCR2 SIM_SCR3 SIM_MSH_ ID SIM_LSH_ID SIM_PUDR Reserved R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W 15 0 0 14 0 0 13 0 0 12 0 0 11 0 0 10 0 0 9 0 0 8 0 0 7 0 0 6 5 4 SW RST 3 2 1 0 EMI_ ONCE MODE EBL0 0 SWR STOP_ DISABLE POR WAIT_ DISABLE 0 0 COPR EXTR FIELD FIELD FIELD FIELD 0 1 0 0 1 0 0 0 1 0 0 0 0 0 0 1 0 1 0 1 0 0 0 0 1 1 0 0 1 1 1 0 1 0 0 0 1 0 PWMA 1 CAN EMI_ RESET MODE IRQ XBOOT PWMB PWMA 0 CTRL JTAG $A $B $C $D $E $F SIM_ CLKOSR SIM_GPS SIM_PCE SIM_ISALH SIM_ISALL SIM_PCE2 0 0 0 0 0 0 0 0 0 0 0 0 A23 0 A22 0 A21 0 A20 0 CLKDIS D1 SCI1 1 D0 SCI0 1 C3 SPI1 1 CLKOSEL C2 SPI0 1 C1 PWM B C0 PWM A EMI 1 ADCB 1 ADCA 1 CAN 1 DEC1 1 DEC0 1 TMRD TMRC TMRB TMRA 1 1 1 1 ISAL[23:22] ISAL[21:6] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CAN2 = Reserved Figure 6-2 SIM Register Map Summary 6.5.1 SIM Control Register (SIM_CONTROL) 15 0 Base + $0 Read Write RESET 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 5 4 SW RST 0 3 2 1 0 EMI_ ONCE MODE EBL 0 0 STOP_ DISABLE 0 0 WAIT_ DISABLE 0 0 0 0 0 0 0 0 0 0 0 Figure 6-3 SIM Control Register (SIM_CONTROL) 6.5.1.1 Reserved--Bits 15-7 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 113 6.5.1.2 EMI_MODE (EMI_MODE)--Bit 6 This bit reflects the current (non-clocked) state of the EMI_MODE pin. During reset, this bit, coupled with the EXTBOOT signal, is used to initialize address bits [19:16] either as GPIO or as address. These settings can be explicitly overwritten using the appropriate GPIO peripheral enable register at any time after reset. In addition, this pin can be used as a general purpose input pin after reset. * * 0 = External address bits [19:16] are initially programmed as GPIO 1 = When booted with EXTBOOT = 1, A[19:16] are initially programmed as address. If EXTBOOT is 0, they are initialized as GPIO. 6.5.1.3 * * OnCE Enable (OnCE EBL)--Bit 5 0 = OnCE clock to 56800E core enabled when core TAP is enabled 1 = OnCE clock to 56800E core is always enabled 6.5.1.4 6.5.1.5 * * * * Software Reset (SW RST)--Bit 4 Stop Disable (STOP_DISABLE)--Bits 3-2 This bit is always read as 0. Writing a 1 to this bit will cause the part to reset. 00 - Stop mode will be entered when the 56800E core executes a STOP instruction 01 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be reprogrammed in the future 10 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be changed by resetting the device 11 - Same operation as 10 6.5.1.6 * * * * Wait Disable (WAIT_DISABLE)--Bits 1-0 00 - Wait mode will be entered when the 56800E core executes a WAIT instruction 01 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be reprogrammed in the future 10 - The HawkV2 WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only be changed by resetting the device 11 - Same operation as 10 6.5.2 SIM Reset Status Register (SIM_RSTSTS) Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this register. Base + $1 Read Write RESET 0 0 0 0 0 0 0 0 0 0 15 0 14 0 13 O 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 SWR 4 COPR 3 EXTR 2 POR 1 0 0 0 0 0 Figure 6-4 SIM Reset Status Register (SIM_RSTSTS) 56F8367 Technical Data, Rev. 3.0 114 Freescale Semiconductor Preliminary Register Descriptions 6.5.2.1 6.5.2.2 Reserved--Bits 15-6 Software Reset (SWR)--Bit 5 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. When 1, this bit indicates that the previous reset occurred as a result of a software reset (write to SW RST bit in the SIM_CONTROL register). This bit will be cleared by any hardware reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit will clear it. 6.5.2.3 COP Reset (COPR)--Bit 4 When 1, the COPR bit indicates the Computer Operating Properly (COP) timer-generated reset has occurred. This bit will be cleared by a Power-On Reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit will clear it. 6.5.2.4 External Reset (EXTR)--Bit 3 If 1, the EXTR bit indicates an external system reset has occurred. This bit will be cleared by a Power-On Reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit position will clear it. Basically, when the EXTR bit is 1, the previous system reset was caused by the external RESET pin being asserted low. 6.5.2.5 Power-On Reset (POR)--Bit 2 When 1, the POR bit indicates a Power-On Reset occurred some time in the past. This bit can only be cleared by software or by another type of reset. Writing a 0 to this bit will set the bit while writing a 1 to the bit position will clear the bit. In summary, if the bit is 1, the previous system reset was due to a Power-On Reset. 6.5.2.6 Reserved--Bits 1-0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.3 SIM Software Control Registers (SIM_SCR0, SIM_SCR1, SIM_SCR2, and SIM_SCR3) Only SIM_SCR0 is shown below. SIM_SCR1, SIM_SCR2, and SIM_SCR3 are identical in functionality. Base + $2 Read 15 14 13 12 11 10 9 8 FIELD 7 6 5 4 3 2 1 0 Write POR 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-5 SIM Software Control Register 0 (SIM_SCR0) 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 115 6.5.3.1 Software Control Data 1 (FIELD)--Bits 15-0 This register is reset only by the Power-On Reset (POR). It has no part-specific functionality and is intended for use by a software developer to contain data that will be unaffected by the other reset sources (RESET pin, software reset, and COP reset). 6.5.4 Most Significant Half of JTAG ID (SIM_MSH_ID) This read-only register displays the most significant half of the JTAG ID for the chip. This register reads $01D6. Base + $6 Read Write RESET 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 1 7 1 6 1 5 0 4 1 3 0 2 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 0 1 0 1 1 0 Figure 6-6 Most Significant Half of JTAG ID (SIM_MSH_ID) 6.5.5 Least Significant Half of JTAG ID (SIM_LSH_ID) This read-only register displays the least significant half of the JTAG ID for the chip. This register reads $D01D. Base + $7 Read Write RESET 15 1 14 1 13 0 12 1 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 1 3 1 2 1 1 0 0 1 1 1 0 1 0 0 0 0 0 0 0 1 1 1 0 1 Figure 6-7 Least Significant Half of JTAG ID (SIM_LSH_ID) 6.5.6 SIM Pull-up Disable Register (SIM_PUDR) Most of the pins on the chip have on-chip pull-up resistors. Pins which can operate as GPIO can have these resistors disabled via the GPIO function. Non-GPIO pins can have their pull-ups disabled by setting the appropriate bit in this register. Disabling pull-ups is done on a peripheral-by-peripheral basis (for pins not muxed with GPIO). Each bit in the register (see Figure 6-8) corresponds to a functional group of pins. See Table 2-2 to identify which pins can deactivate the internal pull-up resistor. Base + $8 Read Write RESET 15 0 14 PWMA1 13 CAN 0 12 EMI_ MODE 0 11 RESET 0 10 IRQ 0 9 XBOOT 0 8 7 6 0 5 CTRL 4 0 3 JTAG 2 0 1 0 0 0 PWMB PWMA0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-8 SIM Pull-up Disable Register (SIM_PUDR) 56F8367 Technical Data, Rev. 3.0 116 Freescale Semiconductor Preliminary Register Descriptions 6.5.6.1 6.5.6.2 6.5.6.3 6.5.6.4 6.5.6.5 6.5.6.6 6.5.6.7 Note: Reserved --Bit 15 PWMA1--Bit 14 CAN--Bit 13 EMI_MODE--Bit 12 RESET--Bit 11 IRQ--Bit 10 XBOOT--Bit 9 In this package, this input pin is double-bonded with the adjacent VSS pin and this bit should be changed to a 1 in order to reduce power consumption. This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This bit controls the pull-up resistors on the FAULTA3 pin. This bit controls the pull-up resistors on the CAN_RX pin. This bit controls the pull-up resistors on the EMI_MODE pin. This bit controls the pull-up resistors on the RESET pin. This bit controls the pull-up resistors on the IRQA and IRQB pins. This bit controls the pull-up resistors on the EXTBOOT pin. 6.5.6.8 6.5.6.9 6.5.6.10 6.5.6.11 6.5.6.12 PWMB--Bit 8 PWMA0--Bit 7 Reserved--Bit 6 CTRL--Bit 5 Reserved--Bit 4 This bit controls the pull-up resistors on the FAULTB0, FAULTB1, FAULTB2, and FAULTB3 pins. This bit controls the pull-up resistors on the FAULTA0, FAULTA1, and FAULTA2 pins. This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. This bit controls the pull-up resistors on the WR and RD pins. This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 117 6.5.6.13 6.5.6.14 JTAG--Bit 3 Reserved--Bit 2-0 This bit controls the pull-up resistors on the TRST, TMS and TDI pins. This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 6.5.7 CLKO Select Register (SIM_CLKOSR) The CLKO select register can be used to multiplex out any one of the clocks generated inside the clock generation and SIM modules. The default value is SYS_CLK. All other clocks primarily muxed out are for test purposes only, and are subject to significant phase shift at high frequencies. The upper four bits of the GPIOB register can function as GPIO, [A23:20], or as additional clock output signals. GPIO has priority and is enabled/disabled via the GPIOB_PER. If GPIOB[7:4] are programmed to operate as peripheral outputs, then the choice between [A23:20] and additional clock outputs is done here in the CLKOSR. The default state is for the peripheral function of GPIOB[7:4] to be programmed as [A23:20]. This can be changed by altering [A23:20] as shown in Figure 6-9. Base + $A Read Write RESET 15 0 14 0 13 0 12 0 11 0 10 0 9 A23 8 A22 0 7 A21 0 6 A20 0 5 CLK DIS 1 4 3 2 CLKOSEL 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-9 CLKO Select Register (SIM_CLKOSR) 6.5.7.1 6.5.7.2 * * Reserved--Bits 15-10 Alternate GPIOB Peripheral Function for A23 (A23)--Bit 9 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 0 = Peripheral output function of GPIOB7 is defined to be A23 1 = Peripheral output function of GPIOB7 is defined to be the oscillator_clock (MSTR_OSC in Figure 3-4) 6.5.7.3 * * Alternate GPIOB Peripheral Function for A22 (A22)--Bit 8 0 = Peripheral output function of GPIOB6 is defined to be A22 1 = Peripheral output function of GPIOB6 is defined to be SYS_CLK2 6.5.7.4 * * Alternate GPIOB Peripheral Function for A21 (A21)--Bit 7 0 = Peripheral output function of GPIOB5 is defined to be A21 1 = Peripheral output function of GPIOB5 is defined to be SYS_CLK 6.5.7.5 * * Alternate GPIOB Peripheral Function fpr A20 (A20)--Bit 6 0 = Peripheral output function of GPIOB4 is defined to be A20 1 = Peripheral output function of GPIOB4 is defined to be the prescaler_clock (FREF in Figure 3-4) 56F8367 Technical Data, Rev. 3.0 118 Freescale Semiconductor Preliminary Register Descriptions 6.5.7.6 * * Clockout Disable (CLKDIS)--Bit 5 0 = CLKOUT output is enabled and will output the signal indicated by CLKOSEL 1 = CLKOUT is tri-stated 6.5.7.7 * * * * * * * * * * * * * * * * * * CLockout Select (CLKOSEL)--Bits 4-0 Selects clock to be muxed out on the CLKO pin. 00000 = SYS_CLK (from OCCS - DEFAULT) 00001 = Reserved for factory test--56800E clock 00010 = Reserved for factory test--XRAM clock 00011 = Reserved for factory test--PFLASH odd clock 00100 = Reserved for factory test--PFLASH even clock 00101 = Reserved for factory test--BFLASH clock 00110 = Reserved for factory test--DFLASH clock 00111 = Oscillator output 01000 = Fout (from OCCS) 01001 = Reserved for factory test--IPB clock 01010 = Reserved for factory test--Feedback (from OCCS, this is path to PLL) 01011 = Reserved for factory test--Prescaler clock (from OCCS) 01100 = Reserved for factory test--Postscaler clock (from OCCS) 01101 = Reserved for factory test--SYS_CLK2 (from OCCS) 01110 = Reserved for factory test--SYS_CLK_DIV2 01111 = Reserved for factory test--SYS_CLK_D 10000 = ADCA clock 10001 = ADCB clock 6.5.8 GPIO Peripheral Select Register (SIM_GPS) Some GPIO pads can have more than one peripheral selected as the alternate function instead of GPIO. For these pads, this register selects which of the alternate peripherals are actually selected for the GPIO peripheral function. This applies to GPIOC, pins 0-3, and to GPIOD, pins 0 and 1. The GPIOC Peripheral Select register can be used to multiplex out any one of the three alternate peripherals for GPIOC. The default peripheral is Quad Decoder 1 and Quad Timer B (NOT available in the 56F8167 device); these peripherals work together. The four I/O pins associated with GPIOC can function as GPIO, Quad Decoder 1/Quad TimerB , or as SPI 1 signals. GPIO is not the default and is enabled/disabled via the GPIOC_PER, as shown in Figure 6-10 and Table 6-2. When GPIOC[3:0] are programmed to operate as peripheral I/O, then the choice between decoder/timer and SPI inputs/outputs is made in the SIM_GPS register and in conjunction with the Quad Timer Status and Control Registers (SCR). The default state is for the peripheral function of GPIOC[3:0] to be programmed as decoder functions. This can be changed by altering the appropriate controls in the indicated registers. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 119 GPIOC_PER Register GPIO Controlled 0 I/O Pad Control 1 SIM_ GPS Register Quad Timer Controlled 0 SPI Controlled 1 Figure 6-10 Overall Control of GPIOC Pads Using SIM_GPS Control Table 6-2 Control of GPIOC Pads Using SIM_GPS Control 1 Control Registers Quad Timer SCR Register OEN bits GPIOC_PER GPIOC_DTR SIM_GPS Pin Function Comments GPIO Input GPIO Output Quad Timer Input / Quad Decoder Input 2 Quad Timer Output / Quad Decoder Input 3 SPI input SPI output 0 0 1 1 1 1 0 1 -- -- -- -- -- -- 0 0 1 1 -- -- 0 1 -- -- See the "Switch Matrix for Inputs to the Timer" table in the 56F8300 Peripheral User Manual for the definition of timer inputs based on the Quad Decoder mode configuration. See SPI controls for determining the direction of each of the SPI pins. 1. This applies to the four pins that serve as Quad Decoder / Quad Timer / SPI / GPIOC functions. A separate set of control bits is used for each pin. 2. Reset configuration 3. Quad Decoder pins are always inputs and function in conjunction with the Quad Timer pins. Two Input/Output pins associated with GPIOD can function as GPIO, EMI (default peripheral) or CAN2 (NOT available on the 56F8167 device) signals. GPIO is the default and is enabled/disabled via the GPIOD_PER, as shown in Figure 6-11 and Table 6-3. When GPIOD[1:0] are programmed to operate as peripheral input/output, then the choice between EMI and CAN2 inputs/outputs is made here in the GPS. 56F8367 Technical Data, Rev. 3.0 120 Freescale Semiconductor Preliminary Register Descriptions GPIOD_PER Register GPIO Controlled 0 I/O Pad Control 1 SIM_ GPS Register EMI Controlled 0 CAN2 Controlled 1 Figure 6-11 Overall Control of GPIOD Pads Using SIM_GPS Control Table 6-3 Control of GPIOD Pads Using SIM_GPS Control 1 Control Registers GPIOD_DDR GPIOD_PER Pin Function SIM_GPS Comments GPIO Input GPIO Output EMI I/O CAN2 0 0 1 1 0 1 -- -- -- -- 0 1 EMI CSn pins are always outputs CAN2_TX is always an output CAN2_RX is always an input 1. This applies to the two pins that serve as EMI CSn / CAN2 / GPIOD functions. A separate set of control bits is used for each pin. Base + $B Read Write RESET 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 D1 4 D0 0 3 C3 0 2 C2 0 1 C1 0 0 C0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 6-12 GPIO Peripheral Select Register (SIM_GPS) 6.5.8.1 Reserved--Bits 15-6 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 121 6.5.8.2 * * GPIOD1 (D1)--Bit 5 This bit selects the alternate function for GPIOD1. 0 = CS3 1 = CAN2_RX 6.5.8.3 * * GPIOD0 (D0)--Bit 4 0 = CS2 1 = CAN2_TX 6.5.8.4 * * GPIOC3 (C3)--Bit 3 This bit selects the alternate function for GPIOC3. 0 = HOME1/TB3 (default - see "Switch Matrix Mode" bits of the Quad Decoder DECCR register in the 56F8300 Peripheral User Manual) 1 = SS1 6.5.8.5 * * GPIOC2 (C2)--Bit 2 This bit selects the alternate function for GPIOC2. 0 = INDEX1/TB2 (default) 1 = MISO1 6.5.8.6 * * GPIOC1 (C1)--Bit 1 This bit selects the alternate function for GPIOC1. 0 = PHASEB1/TB1 (default) 1 = MOSI1 6.5.8.7 * * GPIOC0 (C0)--Bit 0 This bit selects the alternate function for GPIOC0. 0 = PHASEA1/TB0 (default) 1 = SCLK1 6.5.9 Peripheral Clock Enable Register (SIM_PCE) The Peripheral Clock Enable register is used enable or disable clocks to the peripherals as a power savings feature. The clocks can be individually controlled for each peripheral on the chip. Base + $C Read EMI ADCB ADCA CAN 1 1 1 DEC1 DEC0 TMRD 1 1 1 TMRC 1 TMRB 1 TMRA SCI 1 SCI 0 1 1 1 SPI 1 1 SPI 0 1 PWMB 1 PWMA 1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Write RESET 1 Figure 6-13 Peripheral Clock Enable Register (SIM_PCE) 56F8367 Technical Data, Rev. 3.0 122 Freescale Semiconductor Preliminary Register Descriptions 6.5.9.1 * * External Memory Interface Enable (EMI)--Bit 15 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.2 * * Analog-to-Digital Converter B Enable (ADCB)--Bit 14 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.3 * * Analog-to-Digital Converter A Enable (ADCA)--Bit 13 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.4 * * FlexCAN Enable (CAN)--Bit 12 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.5 * * Decoder 1 Enable (DEC1)--Bit 11 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.6 * * Decoder 0 Enable (DEC0)--Bit 10 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.7 * * Quad Timer D Enable (TMRD)--Bit 9 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.8 * * Quad Timer C Enable (TMRC)--Bit 8 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 123 6.5.9.9 * * Quad Timer B Enable (TMRB)--Bit 7 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.10 * * Quad Timer A Enable (TMRA)--Bit 6 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.11 * * Serial Communications Interface 1 Enable (SCI1)--Bit 5 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.12 * * Serial Communications Interface 0 Enable (SCI0)--Bit 4 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.13 * * Serial Peripheral Interface 1 Enable (SPI1)--Bit 3 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.14 * * Serial Peripheral Interface 0 Enable (SPI0)--Bit 2 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.15 * * Pulse Width Modulator B Enable (PWMB)--1 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.5.9.16 * * Pulse Width Modulator A Enable (PWMA)--0 Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 56F8367 Technical Data, Rev. 3.0 124 Freescale Semiconductor Preliminary Register Descriptions 6.5.10 I/O Short Address Location Register (SIM_ISALH and SIM_ISALL) The I/O Short Address Location registers are used to specify the memory referenced via the I/O short address mode. The I/O short address mode allows the instruction to specify the lower six bits of address; the upper address bits are not directly controllable. This register set allows limited control of the full address, as shown in Figure 6-14. Note: If this register is set to something other than the top of memory (EOnCE register space) and the EX bit in the OMR is set to 1, the JTAG port cannot access the on-chip EOnCE registers, and debug functions will be affected. "Hard Coded" Address Portion 6 Bits from I/O Short Address Mode Instruction Instruction Portion 16 Bits from SIM_ISALL Register 2 bits from SIM_ISALH Register Full 24-Bit for Short I/O Address Figure 6-14 I/O Short Address Determination With this register set, an interrupt driver can set the SIM_ISALL register pair to point to its peripheral registers and then use the I/O Short addressing mode to reference them. The ISR should restore this register to its previous contents prior to returning from interrupt. Note: Note: The default value of this register set points to the EOnCE registers. The pipeline delay between setting this register set and using short I/O addressing with the new value is three cycles. Base + $D Read Write RESET 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 0 ISAL[23:22] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 6-15 I/O Short Address Location High Register (SIM_ISALH) 6.5.10.1 Input/Output Short Address Low (ISAL[23:22])--Bit 1-0 This field represents the upper two address bits of the "hard coded" I/O short address. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 125 Base + $E Read 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ISAL[21:6] Write RESET 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Figure 6-16 I/O Short Address Location Low Register (SIM_ISAL) 6.5.10.2 Input/Output Short Address Low (ISAL[21:6])--Bit 15-0 This field represents the lower 16 address bits of the "hard coded" I/O short address. 6.5.11 Peripheral Clock Enable Register 2 (SIM_PCE2) The Peripheral Clock Enable Register 2 is used to enable or disable clocks to the peripherals as a power-saving feaure. The clocks can be individually controller for each peripheral on the chip. Base + $D Read Write RESET 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 CAN 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6.5.11.1 6.5.11.2 * * Reserved--Bits 15-1 CAN2 Enable--Bit 0 This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing. Each bit controls clocks to the indicated peripheral. 1 = Clocks are enabled 0 = The clock is not provided to the peripheral (the peripheral is disabled) 6.6 Clock Generation Overview The SIM uses an internal master clock from the OCCS (CLKGEN) module to produce the peripheral and system (core and memory) clocks. The maximum master clock frequency is 120MHz. Peripheral and system clocks are generated at half the master clock frequency and therefore at a maximum 60MHz. The SIM provides power modes (Stop, Wait) and clock enables (SIM_PCE register, CLK_DIS, ONCE_EBL) to control which clocks are in operation. The OCCS, power modes, and clock enables provide a flexible means to manage power consumption. 56F8367 Technical Data, Rev. 3.0 126 Freescale Semiconductor Preliminary Power Down Modes Overview Power utilization can be minimized in several ways. In the OCCS, crystal oscillator, and PLL may be shut down when not in use. When the PLL is in use, its prescaler and postscaler can be used to limit PLL and master clock frequency. Power modes permit system and/or peripheral clocks to be disabled when unused. Clock enables provide the means to disable individual clocks. Some peripherals provide further controls to disable unused sub-functions. Refer to Part 3 On-Chip Clock Synthesis (OCCS), and the 56F8300 Peripheral User Manual for further details. 6.7 Power Down Modes Overview The 56F8367/56F8167 operate in one of three power-down modes as shown in Table 6-3. Table 6-4 Clock Operation in Power Down Modes Mode Run Wait Core Clocks Active Core and memory clocks disabled Peripheral Clocks Active Active Description Device is fully functional Peripherals are active and can produce interrupts if they have not been masked off. Interrupts will cause the core to come out of its suspended state and resume normal operation. Typically used for power-conscious applications. The only possible recoveries from Stop mode are: 1. CAN traffic (1st message will be lost) 2. Non-clocked interrupts 3. COP reset 4. External reset 5. Power-on reset Stop System clocks continue to be generated in the SIM, but most are gated prior to reaching memory, core and peripherals. All peripherals, except the COP/watchdog timer, run off the IPBus clock frequency, which is the same as the main processor frequency in this architecture. The maximum frequency of operation is SYS_CLK = 60MHz. Refer to the PCE register in Part 6.5.9 and ADC power modes. Power is a function of the system frequency which can be controlled through the OCCS. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 127 6.8 Stop and Wait Mode Disable Function Permanent Disable D D-FLOP Q C 56800E Reprogrammable Disable STOP_DIS D Q D-FLOP Clock Select Reset C R Note: Wait disable circuit is similar Figure 6-17 Stop Disable Circuit The 56800E core contains both STOP and WAIT instructions. Both put the CPU to sleep. For lowest power consumption in Stop mode, the PLL can be shut down. This must be done explicitly before entering Stop mode, since there is no automatic mechanism for this. When the PLL is shut down, the 56800E system clock must be set equal to the oscillator output. Some applications require the 56800E STOP/WAIT instructions be disabled. To disable those instructions, write to the SIM control register (SIM_CONTROL) described in Part 6.5.1. This procedure can be on either a permanent or temporary basis. Permanently assigned applications last only until their next reset. 6.9 Resets The SIM supports four sources of reset. The two asynchronous sources are the external reset pin and the Power-On Reset (POR). The two synchronous sources are the software reset, which is generated within the SIM itself by writting to the SIM_CONTROL register, and the COP reset. Reset begins with the assertion of any of the reset sources. Release of reset to various blocks is sequenced to permit proper operation of the device. A POR reset is first extended for 221 clock cycles to permit stabilization of the clock source, followed by a 32 clock window in which SIM clocking is initiated. It is then followed by a 32 clock window in which peripherals are released to implement Flash security, and, finally, followed by a 32 clock window in which the core is initialized. After completion of the described reset sequence, application code will begin execution. Resets may be asserted asynchronously, but are always released internally on a rising edge of the system clock. 56F8367 Technical Data, Rev. 3.0 128 Freescale Semiconductor Preliminary Operation with Security Enabled Part 7 Security Features The 56F8367/56F8167 offer security features intended to prevent unauthorized users from reading the contents of the Flash Memory (FM) array. The Flash security consists of several hardware interlocks that block the means by which an unauthorized user could gain access to the Flash array. However, part of the security must lie with the user's code. An extreme example would be user's code that dumps the contents of the internal program, as this code would defeat the purpose of security. At the same time, the user may also wish to put a "backdoor" in his program. As an example, the user downloads a security key through the SCI, allowing access to a programming routine that updates parameters stored in another section of the Flash. 7.1 Operation with Security Enabled Once the user has programmed the Flash with his application code, the device can be secured by programming the security bytes located in the FM configuration field, which occupies a portion of the FM array. These non-volatile bytes will keep the part secured through reset and through power-down of the device. Only two bytes within this field are used to enable or disable security. Refer to the Flash Memory section in the 56F8300 Peripheral User Manual for the state of the security bytes and the resulting state of security. When Flash security mode is enabled in accordance with the method described in the Flash Memory module specification, the device will disable external P-space accesses restricting code execution to internal memory, disable EXTBOOT=1 mode, and disable the core EOnCE debug capabilities. Normal program execution is otherwise unaffected. 7.2 Flash Access Blocking Mechanisms The 56F8367/56F8167 have several operating functional and test modes. Effective Flash security must address operating mode selection and anticipate modes in which the on-chip Flash can be compromised and read without explicit user permission. Methods to block these are outlined in the next subsections. 7.2.1 * * * Forced Operating Mode Selection Internal Boot Mode External Boot Mode Secure Mode At boot time, the SIM determines in which functional modes the device will operate. These are: When Flash security is enabled as described in the Flash Memory module specification, the device will boot in internal boot mode, disable all access to external P-space, and start executing code from the Boot Flash at address 0x02_0000. This security affords protection only to applications in which the device operates in internal Flash security mode. Therefore, the security feature cannot be used unless all executing code resides on-chip. When security is enabled, any attempt to override the default internal operating mode by asserting the EXTBOOT pin in conjunction with reset will be ignored. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 129 7.2.2 Disabling EOnCE Access On-chip Flash can be read by issuing commands across the EOnCE port, which is the debug interface for the 56800E core. The TRST, TCLK, TMS, TDO, and TDI pins comprise a JTAG interface onto which the EOnCE port functionality is mapped. When the device boots, the chip-level JTAG TAP (Test Access Port) is active and provides the chip's boundary scan capability and access to the ID register. Proper implementation of Flash security requires that no access to the EOnCE port is provided when security is enabled. The 56800E core has an input which disables reading of internal memory via the JTAG/EOnCE. The FM sets this input at reset to a value determined by the contents of the FM security bytes. 7.2.3 Flash Lockout Recovery If a user inadvertently enables Flash security on the device, a built-in lockout recovery mechanism can be used to reenable access to the device. This mechanism completely reases all on-chip Flash, thus disabling Flash security. Access to this recovery mechanism is built into CodeWarrior via an instruction in memory configuration (.cfg) files. Add, or uncomment the following configuration command: unlock_flash_on_connect 1 For more information, please see CodeWarrior MC56F83xx/DSP5685x Family Targeting Manual. The LOCKOUT_RECOVERY instruction has an associated 7-bit Data Register (DR) that is used to control the clock divider circuit within the FM module. This divider, FM_CLKDIV[6:0], is used to control the period of the clock used for timed events in the FM erase algorithm. This register must be set with appropriate values before the lockout sequence can begin. Refer to the JTAG section of the 56F8300 Peripheral User Manual for more details on setting this register value. The value of the JTAG FM_CLKDIV[6:0] will replace the value of the FM register FMCLKD that divides down the system clock for timed events, as illustrated in Figure 7-1. FM_CLKDIV[6] will map to the PRDIV8 bit, and FM_CLKDIV[5:0] will map to the DIV[5:0] bits. The combination of PRDIV8 and DIV must divide the FM input clock down to a frequency of 150kHz-200kHz. The "Writing the FMCLKD Register" section in the Flash Memory chapter of the 56F8300 Peripheral User Manual gives specific equations for calculating the correct values. 56F8367 Technical Data, Rev. 3.0 130 Freescale Semiconductor Preliminary Flash Access Blocking Mechanisms Flash Memory SYS_CLK 2 input clock 7 FMCLKD 7 7 DIVIDER FM_CLKDIV JTAG FM_ERASE Figure 7-1 JTAG to FM Connection for Lockout Recovery Two examples of FM_CLKDIV calculations follow. EXAMPLE 1: If the system clock is the 8MHz crystal frequency because the PLL has not been set up, the input clock will be below 12.8MHz, so PRDIV8 = FM_CLKDIV[6] = 0. Using the following equation yields a DIV value of 19 for a clock of 200kHz, and a DIV value of 20 for a clock of 190kHz. This translates into an FM_CLKDIV[6:0] value of $13 or $14, respectively. 150[kHz] ( < SYS_CLK (2) (DIV + 1) )< 200[kHz] EXAMPLE 2: In this example, the system clock has been set up with a value of 32MHz, making the FM input clock 16MHz. Because that is greater than 12.8MHz, PRDIV8 = FM_CLKDIV[6] = 1. Using the following equation yields a DIV value of 9 for a clock of 200kHz, and a DIV value of 10 for a clock of 181kHz. This translates to an FM_CLKDIV[6:0] value of $49 or $4A, respectively. 150[kHz] ( < SYS_CLK (2)(8) (DIV + 1) )< 200[kHz] Once the LOCKOUT_RECOVERY instruction has been shifted into the instruction register, the clock divider value must be shifted into the corresponding 7-bit data register. After the data register has been updated, the user must transition the TAP controller into the RUN-TEST/IDLE state for the lockout sequence to commence. The controller must remain in this state until the erase sequence has completed. For details, see the JTAG Section in the 56F8300 Peripheral User Manual. Note: Once the lockout recovery sequence has completed, the user must reset both the JTAG TAP controller (by asserting TRST) and the device (by asserting external chip reset) to return to normal unsecured operation. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 131 7.2.4 Product Analysis The recommended method of unsecuring a programmed device for product analysis of field failures is via the backdoor key access. The customer would need to supply Technical Support with the backdoor key and the protocol to access the backdoor routine in the Flash. Additionally, the KEYEN bit that allows backdoor key access must be set. An alternative method for performing analysis on a secured microcontroller would be to mass-erase and reprogram the Flash with the original code, but modify the security bytes. To insure that a customer does not inadvertently lock himself out of the device during programming, it is recommended that he program the backdoor access key first, his application code second, and the security bytes within the FM configuration field last. Part 8 General Purpose Input/Output (GPIO) 8.1 Introduction This section is intended to supplement the GPIO information found in the 56F8300 Peripheral User Manual and contains only chip-specific information. This information supercedes the generic information in the 56F8300 Peripheral User Manual. 8.2 Memory Maps The width of the GPIO port defines how many bits are implemented in each of the GPIO registers. Based on this and the default function of each of the GPIO pins, the reset values of the GPIOx_PUR and GPIOx_PER registers will change from port to port. Table 8-3 defines the actual reset values of these registers. 8.3 Configuration There are six GPIO ports defined on the 56F8367/56F8167. The width of each port and the associated peripheral function is shown in Table 8-1 and Table 8-2. The specific mapping of GPIO port pins is shown in Table 8-3. Table 8-1 56F8367 GPIO Ports Configuration GPIO Port A B C Port Width 14 8 11 Available Pins in 56F8367 14 8 11 Peripheral Function Reset Function 14 pins - EMI Address pins 8 pins - EMI Address pins 4 pins -DEC1 / TMRB / SPI1 4 pins -DEC0 / TMRA 3 pins -PWMA current sense EMI Address EMI Address DEC1 / TMRB DEC0 / TMRA PWMA current sense 56F8367 Technical Data, Rev. 3.0 132 Freescale Semiconductor Preliminary Configuration Table 8-1 56F8367 GPIO Ports Configuration (Continued) GPIO Port D Port Width 13 Available Pins in 56F8367 13 Peripheral Function Reset Function 6 pins - EMI CSn 2 pins - SCI1 2 pins - EMI CSn 3 pins -PWMB current sense 2 pins - SCI0 2 pins - EMI Address pins 4 pins - SPI0 2 pins - TMRC 4 pins - TMRD 16 pins - EMI Data EMI Chip Selects SCI1 EMI Chip Selects PWMB current sense SCI0 EMI Address SPI0 TMRC TMRD EMI Data E 14 14 F 16 16 Table 8-2 56F8167 GPIO Ports Configuration GPIO Port A B C Port Width 14 8 11 Available Pins in 56F8167 14 8 11 Peripheral Function Reset Function 14 pins - EMI Address pins 8 pins - EMI Address pins 4 pins - SPI1 4 pins - DEC0 / TMRA 3 pins - Dedicated GPIO 6 pins - EMI CSn 2 pins - SCI1 2 pins - EMI CSn 3 pins -PWMB current sense 2 pins - SCI0 2 pins - EMI Address pins 4 pins - SPI0 2 pins - TMRC 4 pins - Dedicated GPIO 16 pins - EMI Data EMI Address EMI Address SPI1 DEC0 / TMRA GPIO EMI Chip Selects SCI1 EMI Chip Selects PWMB current sense SCI0 EMI Address SPI0 TMRC GPIO EMI Data D 13 13 E 14 14 F 16 16 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 133 Table 8-3 GPIO External Signals Map Pins in italics are NOT available in the 56F8167 device GPIO Port GPIO Bit 0 1 2 3 4 5 6 GPIOA 7 8 9 10 11 12 13 0 1 2 GPIOB 3 4 5 6 7 1 Reset Function Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral GPIO1 GPIO1 GPIO1 GPIO1 GPIO GPIO GPIO GPIO Functional Signal A8 A9 A10 A11 A12 A13 A14 A15 A0 A1 A2 A3 A4 A5 A16 A17 A18 A19 A20 / Prescaler_clock A21 / SYS_CLK A22 / SYS_CLK2 A23 / Oscillator_Clock Package Pin 19 20 21 22 23 24 25 26 154 10 11 12 13 14 33 34 35 36 37 46 47 48 This is a function of the EMI_MODE, EXTBOOT, and Flash security settings at reset. 56F8367 Technical Data, Rev. 3.0 134 Freescale Semiconductor Preliminary Configuration Table 8-3 GPIO External Signals Map (Continued) Pins in italics are NOT available in the 56F8167 device GPIO Port GPIO Bit 0 1 2 3 4 GPIOC 5 6 7 8 9 10 0 1 2 3 4 5 GPIOD 6 7 8 9 10 11 12 Reset Function Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral GPIO GPIO GPIO GPIO GPIO GPIO Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Functional Signal PhaseA1 / TB0 / SCLK11 PhaseB1 / TB1 / MOSI11 Index1 / TB2 / MISO11 Home1 / TB3 / SSI11 PHASEA0 / TA0 PHASEB0 / TA1 Index0 / TA2 Home0 / TA3 ISA0 ISA1 ISA2 CS2 / CAN2_TX CS3 / CAN2_RX CS4 CS5 CS6 CS7 TXD1 RXD1 PS / CS0 DS / CS1 ISB0 ISB1 ISB2 Package Pin 6 7 8 9 155 156 157 158 126 127 128 55 56 57 58 59 60 49 50 53 54 61 63 64 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 135 Table 8-3 GPIO External Signals Map (Continued) Pins in italics are NOT available in the 56F8167 device GPIO Port GPIO Bit 0 1 2 3 4 5 6 GPIOE 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 GPIOF 8 9 10 11 12 13 14 15 Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral D15 D0 D1 D2 D3 D4 D5 D6 153 70 71 83 86 88 89 90 Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral SS0 TC0 TC1 TD0 TD1 TD2 TD3 D7 D8 D9 D10 D11 D12 D13 D14 145 133 135 129 130 131 132 28 29 30 32 149 150 151 152 Reset Function Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Peripheral Functional Signal TXD0 RXD0 A6 A7 SCLK0 MOSI0 MISO0 Package Pin 4 5 17 18 146 148 147 1. See Part 6.5.8 to determine how to select peripherals from this set 56F8367 Technical Data, Rev. 3.0 136 Freescale Semiconductor Preliminary 56F8367 Information Part 9 Joint Test Action Group (JTAG) 9.1 56F8367 Information Please contact your Freescale marketing device/package-specific BSDL information. representative or authorized distributor for Part 10 Specifications 10.1 General Characteristics The 56F8367/56F8167 are fabricated in high-density CMOS with 5V-tolerant TTL-compatible digital inputs. The term "5V-tolerant" refers to the capability of an I/O pin, built on a 3.3V-compatible process technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices designed for 3.3V and 5V power supplies. In such sytems, a bus may carry both 3.3V- and 5V-compatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V 10% during normal operation without causing damage). This 5V-tolerant capability therefore offers the power savings of 3.3V I/O levels combined with the ability to receive 5V levels without damage. Absolute maximum ratings in Table 10-1 are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent damage to the device. Note: All specifications meet both Automotive and Industrial requirements unless individual specifications are listed. Note: The 56F8167 device is guaranteed to 40HMz and specified to meet Industrial requirements only. CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 137 Note: The 56F8167 device is specified to meet Industrial requirements only; CAN is NOT available on the 56F8167 device. Table 10-1 Absolute Maximum Ratings (VSS = VSSA_ADC = 0) Characteristic Supply Voltage ADC Supply Voltage Symbol VDD_IO VDDA_ADC, VREFH VDDA_OSC_PLL VDD_CORE VIN VINA VOUT VOD TA TA TJ TJ TSTG TSTG OCR_DIS is High Pin Groups 1, 2, 5, 6, 9, 10 Pin Groups 11, 12, 13 Pin Groups 1, 2, 3, 5, 6, 7, 8 Notes Min -0.3 Max 4.0 4.0 Unit V V VREFH must be less than or equal to VDDA_ADC -0.3 Oscillator / PLL Supply Voltage Internal Logic Core Supply Voltage Input Voltage (digital) Input Voltage (analog) Output Voltage Output Voltage (open drain) Ambient Temperature (Automotive) Ambient Temperature (Industrial) Junction Temperature (Automotive) Junction Temperature (Industrial) Storage Temperature (Automotive) Storage Temperature (Industrial) -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -40 -40 -40 -40 -55 -55 4.0 3.0 6.0 4.0 4.0 6.01 6.0 125 105 150 125 150 150 V V V V V V C C C C C C Pin Group 4 1. If corresponding GPIO pin is configured as open drain. Note: Pins in italics are NOT available in the 56F8167 device. Pin Group 1: TXD0-1, RXD0-1, SS0, MISO0, MOSI0 Pin Group 2: PHASEA0, PHASEA1, PHASEB0, PHASEB1, INDEX0, INDEX1, HOME0, HOME1, ISB0-2, ISA0-2, TD2-3, TC0-1, SCLK0 Pin Group 3: RSTO, TDO Pin Group 4: CAN_TX Pin Group 5: A0-5, D0-15, GPIOD0-5, PS, DS Pin Group 6: A6-15, GPIOB0-7, TD0-1 Pin Group 7: CLKO, WR, RD Pin Group 8: PWMA0-5, PWMB0-5 Pin Group 9: IRQA, IRQB, RESET, EXTBOOT, TRST, TMS, TDI, CAN_RX, EMI_MODE, FAULTA0-3, FAULTB0-3 Pin Group 10: TCK Pin Group 11: XTAL, EXTAL Pin Group 12: ANA0-7, ANB0-7 Pin Group 13: OCR_DIS, CLKMODE 56F8367 Technical Data, Rev. 3.0 138 Freescale Semiconductor Preliminary General Characteristics Table 10-2 56F8367/56F8167 ElectroStatic Discharge (ESD) Protection Characteristic ESD for Human Body Model (HBM) ESD for Machine Model (MM) ESD for Charge Device Model (CDM) Min 2000 200 500 Typ -- -- -- Max -- -- -- Unit V V V Table 10-3 Thermal Characteristics6 Value Characteristic Value Unit 160-pin LQFP Junction to ambient Natural convection Junction to ambient (@1m/sec) Junction to ambient Natural convection Junction to ambient (@1m/sec) Junction to case Junction to center of case I/O pin power dissipation Power dissipation Maximum allowed PD Four layer board (2s2p) Four layer board (2s2p) RJA RJMA RJMA (2s2p) RJMA (2s2p) RJC JT P I/O PD PDMAX Comments Symbol 160MAPBGA 39.90 46.8 TBD TBD TBD TBD Notes 38.5 35.4 33 31.5 8.6 0.8 C/W C/W C/W C/W C/W C/W W W W 2 2 1, 2 1, 2 3 4, 5 User-determined P D = (IDD x VDD + P I/O) (TJ - TA) / RJA7 1. Theta-JA determined on 2s2p test boards is frequently lower than would be observed in an application. Determined on 2s2p thermal test board. 2. Junction to ambient thermal resistance, Theta-JA (RJA) was simulated to be equivalent to the JEDEC specification JESD51-2 in a horizontal configuration in natural convection. Theta-JA was also simulated on a thermal test board with two internal planes (2s2p, where "s" is the number of signal layers and "p" is the number of planes) per JESD51-6 and JESD51-7. The correct name for Theta-JA for forced convection or with the non-single layer boards is Theta-JMA. 3. Junction to case thermal resistance, Theta-JC (RJC ), was simulated to be equivalent to the measured values using the cold plate technique with the cold plate temperature used as the "case" temperature. The basic cold plate measurement technique is described by MIL-STD 883D, Method 1012.1. This is the correct thermal metric to use to calculate thermal performance when the package is being used with a heat sink. 4. Thermal Characterization Parameter, Psi-JT (JT ), is the "resistance" from junction to reference point thermocouple on top center of case as defined in JESD51-2. JT is a useful value to use to estimate junction temperature in steady-state customer environments. 5. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 6. See Part 12.1 for more details on thermal design considerations. 7. TJ = Junction temperature TA = Ambient temperature TBD = numbers will be available late Q4 2005 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 139 Note: The 56F8167 device is guaranteed to 40HMz and specified to meet Industrial requirements only; CAN is NOT available on the 56F8167 device. Table 10-4 Recommended Operating Conditions (VREFLO = 0V, VSS = VSSA_ADC = 0V, VDDA = VDDA_ADC = VDDA_OSC_PLL ) Characteristic Supply voltage ADC Supply Voltage Oscillator / PLL Supply Voltage Internal Logic Core Supply Voltage Device Clock Frequency Input High Voltage (digital) Input High Voltage (analog) Input High Voltage (XTAL/EXTAL, XTAL is not driven by an external clock) Symbol VDD_IO VDDA_ADC, VREFH VDDA_OSC _PLL Notes Min 3 Typ 3.3 3.3 3.3 2.5 -- -- -- -- Max 3.6 3.6 3.6 2.75 60 5.5 VDDA+0.3 VDDA+0.3 Unit V V VREFH must be less than or equal to VDDA_ADC 3 3 V V VDD_CORE FSYSCLK VIH VIHA VIHC OCR_DIS is High 2.25 0 MHz V V V Pin Groups 1, 2, 5, 6, 9, 10 Pin Group 13 Pin Group 11 2 2 VDDA-0.8 Input high voltage (XTAL/EXTAL, XTAL is driven by an external clock) VIHC VIL IOH Pin Group 11 2 -0.3 -- -- -- -- -- -- -40 -40 -- -- -- -- -- -- -- -- -- -- -- -- -- VDDA+0.3 0.8 -4 -8 -12 4 8 12 125 = 150 (RJA X PD) 105 = 125 (RJA X PD) V Input Low Voltage Output High Source Current VOH = 2.4V (VOH min.) Pin Groups 1, 2, 5, 6, 9, 10, 11, 13 Pin Groups 1, 2, 3 Pin Groups 5, 6, 7 Pin Group 8 V mA Output Low Sink Current VOL = 0.4V (VOL max) IOL Pin Groups 1, 2, 3, 4 Pin Groups 5, 6, 7 Pin Group 8 mA Ambient Operating Temperature (Automotive) Ambient Operating Temperature (Industrial) Flash Endurance (Automotive) (Program Erase Cycles) Flash Endurance (Industrial) (Program Erase Cycles) Flash Data Retention TA C TA C NF NF TR TA = -40C to 125C 1000 1000 15 -- -- -- Cycles TA = -40C to 105C Cycles TJ <= 85C avg Years Note: Total chip source or sink current cannot exceed 200mA See Pin Groups in Table 10-1. 56F8367 Technical Data, Rev. 3.0 140 Freescale Semiconductor Preliminary DC Electrical Characteristics 10.2 DC Electrical Characteristics Note: The 56F8167 device is specified to meet Industrial requirements only; CAN is NOT available on the 56F8167 device. Table 10-5 DC Electrical Characteristics At Recommended Operating Conditions;see Table 10-4 Characteristic Output High Voltage Output Low Voltage Digital Input Current High pull-up enabled or disabled Symbol VOH VOL IIH IIH IIHA IIHADC IIL IIL IIL IILA IILADC IEXTAL IXTAL Notes Min 2.4 -- Typ -- -- 0 80 0 0 -100 0 0 0 0 0 0 -- 0 0.3 4.5 5.5 6 6 Max -- 0.4 +/- 2.5 160 +/- 2.5 +/- 10 -500 +/- 2.5 +/- 2.5 +/- 2.5 +/- 10 +/- 2.5 +/- 2.5 200 +/- 2.5 -- -- -- -- -- Unit V V A A A A A A A A A A A A A Test Conditions IOH = IOHmax IOL = IOLmax VIN = 3.0V to 5.5V VIN = 3.0V to 5.5V VIN = VDDA VIN = VDDA VIN = 0V VIN = 0V VIN = 0V VIN = 0V VIN = 0V VIN = VDDA or 0V VIN = VDDA or 0V VIN = VDDA or 0V VOUT = 3.0V to 5.5V or 0V Pin Groups 1, 2, 5, 6, 9 -- 40 -- -- -200 -- -- -- -- -- Digital Input Current High with pull-down Pin Group 10 Analog Input Current High ADC Input Current High Digital Input Current Low pull-up enabled Pin Group 13 Pin Group 12 Pin Groups 1, 2, 5, 6, 9 Digital Input Current Low pull-up disabled Pin Groups 1, 2, 5, 6, 9 Digital Input Current Low with pull-down Pin Group 10 Analog Input Current Low ADC Input Current Low EXTAL Input Current Low clock input Pin Group 13 Pin Group 12 XTAL Input Current Low clock input CLKMODE = High CLKMODE = Low -- -- -- -- -- -- -- -- Output Current High Impedance State Schmitt Trigger Input Hysteresis Input Capacitance (EXTAL/XTAL) Output Capacitance (EXTAL/XTAL) Input Capacitance Output Capacitance See Pin Groups in Table 10-1. IOZ VHYS CINC COUTC CIN COUT Pin Groups 1, 2, 3, 4, 5, 6, 7, 8,14 Pin Groups 2, 6, 9, 10 V -- -- -- -- -- pF pF pF pF 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 141 Table 10-6 Power-On Reset Low Voltage Parameters Characteristic POR Trip Point LVI, 2.5 volt Supply, trip point1 LVI, 3.3 volt supply, trip point2 Bias Current Symbol POR VEI2.5 VEI3.3 I bias Min 1.75 -- -- -- Typ 1.8 2.14 2.7 110 Max 1.9 -- -- 130 Units V V V A 1. When VDD_CORE drops below VEI2.5, an interrupt is generated. 2. When VDD_CORE drops below VEI3.3, an interrupt is generated. Table 10-7 Current Consumption per Power Supply Pin (Typical) On-Chip Regulator Enabled (OCR_DIS = Low) Mode RUN1_MAC IDD_IO1 155mA IDD_ADC 50mA IDD_OSC_PLL 2.5mA Test Conditions * 60MHz Device Clock * All peripheral clocks are enabled * All peripherals running * Continuous MAC instructions with fetches from Data RAM * ADC powered on and clocked Wait3 91mA 70A 2.5mA * 60MHz Device Clock * All peripheral clocks are enabled * ADC powered off Stop1 6mA 0A 165A * 8MHz Device Clock * All peripheral clocks are off * ADC powered off * PLL powered off Stop2 5.1mA 0A 155A * External Clock is off * All peripheral clocks are off * ADC powered off * PLL powered off 1. No Output Switching 2. Includes Processor Core current supplied by internal voltage regulator 56F8367 Technical Data, Rev. 3.0 142 Freescale Semiconductor Preliminary DC Electrical Characteristics Table 10-8 Current Consumption per Power Supply Pin (Typical) On-Chip Regulator Disabled (OCR_DIS = High) Mode RUN1_MAC IDD_Core 150mA IDD_IO1 13A IDD_ADC 50mA IDD_OSC_PLL 2.5mA Test Conditions * 60MHz Device Clock * All peripheral clocks are enabled * All peripherals running * Continuous MAC instructions with fetches from Data RAM * ADC powered on and clocked Wait3 86mA 13A 70A 2.5mA * 60MHz Device Clock * All peripheral clocks are enabled * ADC powered off Stop1 950A 13A 0A 165A * 8MHz Device Clock * All peripheral clocks are off * ADC powered off * PLL powered off Stop2 100A 13A 0A 155A * External Clock is off * All peripheral clocks are off * ADC powered off * PLL powered off 1. No Output Switching Table 10-9. Regulator Parameters Characteristic Unloaded Output Voltage (0mA Load) Loaded Output Voltage (200 mA load) Line Regulation @ 250 mA load (VDD33 ranges from 3.0 to 3.6) Short Circuit Current ( output shorted to ground) Bias Current Power-down Current Short-Circuit Tolerance (output shorted to ground) Symbol VRNL VRL VR Iss I bias Ipd TRSC Min 2.25 2.25 2.25 -- -- -- -- Typical -- -- -- -- 5.8 0 -- Max 2.75 2.75 2.75 700 7 2 30 Unit V V V mA mA A minutes 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 143 Table 10-10. PLL Parameters Characteristics PLL Start-up time Resonator Start-up time Min-Max Period Variation Peak-to-Peak Jitter Bias Current Quiescent Current, power-down mode Symbol TPS TRS TPV TPJ IBIAS IPD Min 0.3 0.1 120 -- -- -- Typical 0.5 0.18 -- -- 1.5 100 Max 10 1 200 175 2 150 Unit ms ms ps ps mA A 10.2.1 Temperature Sense Note: Temperature Sensor is NOT available in the 56F8167 device. Table 10-11 Temperature Sense Parametrics Characteristics Slope (Gain)1 Room Trim Temp. 1, 2 Hot Trim Temp. (Industrial)1,2 Hot Trim Temp. (Automotive)1,2 Output Voltage @ VDDA_ADC = 3.3V, TJ =0C1 Supply Voltage Supply Current - OFF Supply Current - ON Accuracy3,1 from -40C to 150C Using VTS = mT + VTS0 Resolution4, 5,1 Symbol m TRT THT THT VTS0 Min -- 24 122 147 -- Typical 7.762 26 125 150 1.370 Max -- 28 128 153 -- Unit mV/C C C C V VDDA_ADC IDD-OFF IDD-ON TACC 3.0 -- -- -6.7 3.3 -- -- 0 3.6 10 250 6.7 V A A C RES -- 0.104 -- C / bit 1. Includes the ADC conversion of the analog Temperature Sense voltage. 2. The ADC is not calibrated for the conversion of the Temperature Sensor trim value stored in the Flash Memory at FMOPT0 and FMOPT1. 3. See Application Note, AN1980, for methods to increase accuracy. 4. Assuming a 12-bit range from 0V to 3.3V. 5. Typical resolution calculated using equation, RES = (VREFH - VREFLO) X 1 212 m 56F8367 Technical Data, Rev. 3.0 144 Freescale Semiconductor Preliminary AC Electrical Characteristics 10.3 AC Electrical Characteristics Tests are conducted using the input levels specified in Table 10-5. Unless otherwise specified, propagation delays are measured from the 50% to the 50% point, and rise and fall times are measured between the 10% and 90% points, as shown in Figure 10-1. VIH Input Signal Midpoint1 Fall Time Note: The midpoint is VIL + (VIH - VIL)/2. Low High 90% 50% 10% VIL Rise Time Figure 10-1 Input Signal Measurement References Figure 10-2 shows the definitions of the following signal states: * * * * Active state, when a bus or signal is driven, and enters a low impedance state Tri-stated, when a bus or signal is placed in a high impedance state Data Valid state, when a signal level has reached VOL or VOH Data Invalid state, when a signal level is in transition between VOL and VOH Data1 Valid Data1 Data Invalid State Data Active Data2 Valid Data2 Data Tri-stated Data Active Data3 Valid Data3 Figure 10-2 Signal States 10.4 Flash Memory Characteristics Table 10-12 Flash Timing Parameters Characteristic Program time1 Erase time2 Mass erase time Symbol Min 20 20 100 Typ -- -- -- Max -- -- -- Unit s ms ms Tprog Terase Tme 1. There is additional overhead which is part of the programming sequence. See the 56F8300 Peripheral User Manual for details. Program time is per 16-bit word in Flash memory. Two words at a time can be programmed within the Program Flash Module, as it contains two interleaved memories. 2. Specifies page erase time. There are 512 bytes per page in the Data and Boot Flash memories. The Program Flash Module uses two interleaved Flash memories, increasing the effective page size to 1024 bytes. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 145 10.5 External Clock Operation Timing Table 10-13 External Clock Operation Timing Requirements1 Characteristic Frequency of operation (external clock driver)2 Clock Pulse Width3 External clock input rise time4 External clock input fall time5 1. Parameters listed are guaranteed by design. 2. See Figure 10-3 for details on using the recommended connection of an external clock driver. 3. The high or low pulse width must be no smaller than 8.0ns or the chip will not function. 4. External clock input rise time is measured from 10% to 90%. 5. External clock input fall time is measured from 90% to 10%. Symbol fosc tPW trise tfall Min 0 3.0 -- -- Typ -- -- -- -- Max 120 -- 10 10 Unit MHz ns ns ns VIH External Clock 90% 50% 10% 90% 50% 10% tPW tPW tfall trise VIL Note: The midpoint is VIL + (VIH - VIL)/2. Figure 10-3 External Clock Timing 10.6 Phase Locked Loop Timing Table 10-14 PLL Timing Characteristic External reference crystal frequency for the PLL1 PLL output frequency2 (fOUT) PLL stabilization time3 -40 to +125C Symbol fosc fop tplls Min 4 160 -- Typ 8 -- 1 Max 8 260 10 Unit MHz MHz ms 1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly. The PLL is optimized for 8MHz input crystal. 2. ZCLK may not exceed 60MHz. For additional information on ZCLK and (fOUT/2), please refer to the OCCS chapter in the 56F8300 Peripheral User Manual. 3. This is the minimum time required after the PLL set up is changed to ensure reliable operation. 56F8367 Technical Data, Rev. 3.0 146 Freescale Semiconductor Preliminary Crystal Oscillator Timing 10.7 Crystal Oscillator Timing Table 10-15 Crystal Oscillator Parameters Characteristic Crystal Start-up time Resonator Start-up time Crystal ESR Crystal Peak-to-Peak Jitter Crystal Min-Max Period Variation Resonator Peak-to-Peak Jitter Resonator Min-Max Period Variation Bias Current, high-drive mode Bias Current, low-drive mode Quiescent Current, power-down mode Symbol TCS TRS RESR TD TPV TRJ TRP IBIASH IBIASL IPD Min 4 0.1 -- 70 0.12 -- -- -- -- -- Typ 5 0.18 -- -- -- -- -- 250 80 0 Max 10 1 120 250 1.5 300 300 290 110 1 Unit ms ms ohms ps ns ps ps A A A 10.8 External Memory Interface Timing The External Memory Interface is designed to access static memory and peripheral devices. Figure 10-4 shows sample timing and parameters that are detailed in Table 10-16. The timing of each parameter consists of both a fixed delay portion and a clock related portion, as well as user controlled wait states. The equation: t = D + P * (M + W) should be used to determine the actual time of each parameter. The terms in this equation are defined as: t D P M W = Parameter delay time = Fixed portion of the delay, due to on-chip path delays = Period of the system clock, which determines the execution rate of the part (i.e., when the device is operating at 60MHz, P = 16.67 ns) = Fixed portion of a clock period inherent in the design; this number is adjusted to account for possible derating of clock duty cycle = Sum of the applicable wait state controls. The "Wait State Controls" column of Table 10-16 shows the applicable controls for each parameter and the EMI chapter of the 56F8300 Peripheral User Manual details what each wait state field controls. When using the XTAL clock input directly as the chip clock without prescaling (ZSRC selects prescaler clock and prescaler set to / 1), the EMI quadrature clock is generated using both edges of the EXTAL clock input. In this situation only, parameter values must be adjusted for the duty cycle at XTAL. DCAOE and DCAEO are used to make this duty cycle adjustment where needed. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 147 DCAOE and DCAEO are calculated as follows: DCAOE = 0.5 - MAX XTAL duty cycle, if ZSRC selects prescaler clock and the prescaler is set to / 1 = 0.0 all other cases DCAEO = MIN XTAL duty cycle - 0.5, if ZSRC selects prescaler clock and the prescaler is set to / 1 = 0.0 all other cases Example of DCAOE and DCAEO calculation: Assuming prescaler is set for / 1 and prescaler clock is selected by ZSRC, if XTAL duty cycle ranges between 45% and 60% high; DCAOE = .50 - .60 = - 0.1 DCAEO = .45 - .50 = - 0.05 The timing of write cycles is different when WWS = 0 than when WWS > 0. Therefore, some parameters contain two sets of numbers to account for this difference. Use the "Wait States Configuration" column of Table 10-16 to make the appropriate selection. A0-Axx,CS tRD tARDD tARDA RD tAWR tWRWR WR tWR tWAC tWRRD tRDWR tRDA tRDRD tDWR tDOS D0-D15 tDOH tAD tRDD tDRD Data Out Data In Note: During read-modify-write instructions and internal instructions, the address lines do not change state. Figure 10-4 External Memory Interface Timing Note: When multiple lines are given for the same wait state configuration, calculate each and then select the smallest or most negative. 56F8367 Technical Data, Rev. 3.0 148 Freescale Semiconductor Preliminary External Memory Interface Timing Table 10-16 External Memory Interface Timing Characteristic Address Valid to WR Asserted WR Width Asserted to WR Deasserted Data Out Valid to WR Asserted tDWR Symbol tAWR tWR Wait States Configuration WWS=0 WWS>0 WWS=0 WWS>0 WWS=0 WWS=0 WWS>0 WWS>0 D -2.076 -1.795 -0.094 -0.012 -9.321 -1.160 -8.631 -0.879 -2.086 -0.563 -8.315 -3.432 -1.780 -2.120 0.00 0.279 -15.723 -20.642 -2.603 -13.120 -18.039 -2.135 -0.4832 M 0.50 0.75 + DCAOE 0.25 + DCAOE 0 0.25 + DCAEO 0.00 0.50 0.25 + DCAOE 0.25 + DCAEO 0.25 + DCAOE 0.50 0.25 + DCAEO 0.00 1.00 N/A1 1.00 1.00 1.25 + DCAOE 0.00 1.00 1.25 + DCAOE 0.25 + DCAEO 0.00 0.75 + DCAEO 1.00 0.50 0.75 + DCAOE Wait States Controls WWSS WWS Unit ns ns WWSS ns Valid Data Out Hold Time after WR Deasserted Valid Data Out Set-Up Time to WR Deasserted Valid Address after WR Deasserted RD Deasserted to Address Invalid Address Valid to RD Deasserted Valid Input Data Hold after RD Deasserted RD Assertion Width Address Valid to Input Data Valid Address Valid to RD Asserted RD Asserted to Input Data Valid WR Deasserted to RD Asserted RD Deasserted to RD Asserted WR Deasserted to WR Asserted RD Deasserted to WR Asserted tDOH tDOS tWAC tRDA tARDD tDRD tRD tAD tARDA tRDD tWRRD tRDRD tWRWR tRDWR WWS=0 WWS>0 WWS=0 WWS>0 WWSH WWS,WWSS WWSH RWSH RWSS,RWS -- RWS RWSS,RWS RWSS RWSS,RWS WWSH,RWSS RWSS,RWSH MDAR3, 4 WWSS, WWSH RWSH, WWSS, MDAR3 ns ns ns ns ns ns ns ns ns ns ns ns ns ns -1.608 -0.918 -0.096 0.084 1. N/A since device captures data before it deasserts RD 2. If RWSS = RWSH = 0, and the chip select does not change, then RD does not deassert during back-to-back reads. 3. Substitute BMDAR for MDAR if there is no chip select 4. MDAR is active in this calculation only when the chip select changes. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 149 10.9 Reset, Stop, Wait, Mode Select, and Interrupt Timing Table 10-17 Reset, Stop, Wait, Mode Select, and Interrupt Timing1,2 Characteristic RESET Assertion to Address, Data and Control Signals High Impedance Minimum RESET Assertion Duration RESET Deassertion to First External Address Output3 Edge-sensitive Interrupt Request Width IRQA, IRQB Assertion to External Data Memory Access Out Valid, caused by first instruction execution in the interrupt service routine IRQA, IRQB Assertion to General Purpose Output Valid, caused by first instruction execution in the interrupt service routine Delay from IRQA Assertion (exiting Wait) to External Data Memory Access4 Symbol tRAZ tRA tRDA Typical Min -- 16T 63T Typical Max 21 -- 64T Unit ns ns ns See Figure 10-5 10-5 10-5 tIRW tIDM tIDM - FAST tIG tIG - FAST tIRI tIRI -FAST 1.5T 18T 14T 18T 14T 22T 18T 22T 18T 1.5T -- -- -- -- -- -- -- -- -- -- ns ns 10-6 10-7 ns 10-7 ns 10-8 Delay from IRQA Assertion to External Data Memory Access (exiting Stop) tIF tIF - FAST ns 10-9 IRQA Width Assertion to Recover from Stop State5 tIW ns 10-9 1. In the formulas, T = clock cycle. For an operating frequency of 60MHz, T = 16.67ns. At 8MHz (used during Reset and Stop modes), T = 125ns. 2. Parameters listed are guaranteed by design. 3. During Power-On Reset, it is possible to use the device's internal reset stretching circuitry to extend this period to 221T. 4. The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is not the minimum required so that the IRQA interrupt is accepted. 5. The interrupt instruction fetch is visible on the pins only in Mode 3. 56F8367 Technical Data, Rev. 3.0 150 Freescale Semiconductor Preliminary Reset, Stop, Wait, Mode Select, and Interrupt Timing RESET tRA tRAZ tRDA A0-A15, D0-D15 PS, DS, RD, WR First Fetch First Fetch Figure 10-5 Asynchronous Reset Timing IRQA, IRQB tIRW Figure 10-6 External Interrupt Timing (Negative Edge-Sensitive) A0-A15, PS, DS, RD, WR tIDM IRQA, IRQB First Interrupt Instruction Execution a) First Interrupt Instruction Execution General Purpose I/O Pin tIG IRQA, IRQB b) General Purpose I/O Figure 10-7 External Level-Sensitive Interrupt Timing 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 151 IRQA, IRQB tIRI A0-A15, PS, DS, RD, WR First Interrupt Vector Instruction Fetch Figure 10-8 Interrupt from Wait State Timing tIW IRQA tIF A0-A15, PS, DS, RD, WR First Instruction Fetch Not IRQA Interrupt Vector Figure 10-9 Recovery from Stop State Using Asynchronous Interrupt Timing 10.10 Serial Peripheral Interface (SPI) Timing Table 10-18 SPI Timing1 Characteristic Cycle time Master Slave Enable lead time Master Slave Enable lag time Master Slave Clock (SCK) high time Master Slave Clock (SCK) low time Master Slave Symbol tC 50 50 tELD -- 25 tELG -- 100 tCH 17.6 25 tCL 24.1 25 -- -- ns ns -- -- ns ns -- -- ns ns 10-10, 10-11, 10-12, 10-13 -- -- ns ns 10-13 -- -- ns ns Min Max Unit See Figure 10-10, 10-11, 10-12, 10-13 10-13 10-13 56F8367 Technical Data, Rev. 3.0 152 Freescale Semiconductor Preliminary Serial Peripheral Interface (SPI) Timing Table 10-18 SPI Timing1 (Continued) Characteristic Data set-up time required for inputs Master Slave Data hold time required for inputs Master Slave Access time (time to data active from high-impedance state) Slave Disable time (hold time to high-impedance state) Slave Data Valid for outputs Master Slave (after enable edge) Data invalid Master Slave Rise time Master Slave Fall time Master Slave 1. Parameters listed are guaranteed by design. Symbol tDS Min Max Unit See Figure 10-10, 10-11, 10-12, 10-13 20 0 tDH 0 2 tA 4.8 tD 3.7 tDV -- -- tDI 0 0 tR -- -- tF -- -- -- -- ns ns -- -- ns ns 10-10, 10-11, 10-12, 10-13 10-13 15 ns 10-13 15.2 ns 10-10, 10-11, 10-12, 10-13 4.5 20.4 ns ns -- -- ns ns 10-10, 10-11, 10-12 11.5 10.0 ns ns 10-10, 10-11, 10-12, 10-13 9.7 9.0 ns ns 10-10, 10-11, 10-12, 10-13 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 153 SS (Input) SS is held High on master tC tR tF SCLK (CPOL = 0) (Output) tCL tCH tF tR SCLK (CPOL = 1) (Output) tDH tDS tCL tCH MISO (Input) MSB in tDI Bits 14-1 tDV LSB in tDI(ref) MOSI (Output) Master MSB out tF Bits 14-1 Master LSB out tR Figure 10-10 SPI Master Timing (CPHA = 0) SS (Input) tC SS is held High on master tF tCL tR SCLK (CPOL = 0) (Output) tCH tF SCLK (CPOL = 1) (Output) tCL tCH tR tDS tDH MISO (Input) tDV(ref) MSB in tDI Bits 14-1 tDV LSB in tDI(ref) MOSI (Output) Master MSB out tF Bits 14- 1 Master LSB out tR Figure 10-11 SPI Master Timing (CPHA = 1) 56F8367 Technical Data, Rev. 3.0 154 Freescale Semiconductor Preliminary Serial Peripheral Interface (SPI) Timing SS (Input) tC tCL tR tF tELG SCLK (CPOL = 0) (Input) tELD tCH SCLK (CPOL = 1) (Input) tA tCL tCH tR tF tD MISO (Output) tDS Slave MSB out Bits 14-1 tDV tDH Slave LSB out tDI tDI MOSI (Input) MSB in Bits 14-1 LSB in Figure 10-12 SPI Slave Timing (CPHA = 0) SS (Input) tC tF tR tCL tCH tELD tCL tELG SCLK (CPOL = 0) (Input) SCLK (CPOL = 1) (Input) tDV tA tCH tF tR tD MISO (Output) tDS Slave MSB out Bits 14-1 tDV tDH Slave LSB out tDI MOSI (Input) MSB in Bits 14-1 LSB in Figure 10-13 SPI Slave Timing (CPHA = 1) 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 155 10.11 Quad Timer Timing Table 10-19 Timer Timing1, 2 Characteristic Timer input period Timer input high / low period Timer output period Timer output high / low period Symbol PIN PINHL POUT POUTHL Min 2T + 6 1T + 3 1T - 3 0.5T - 3 Max -- -- -- -- Unit ns ns ns ns See Figure 10-14 10-14 10-14 10-14 1. In the formulas listed, T = the clock cycle. For 60MHz operation, T = 16.67ns. 2. Parameters listed are guaranteed by design. Timer Inputs PIN PINHL PINHL Timer Outputs POUT POUTHL POUTHL Figure 10-14 Timer Timing 10.12 Quadrature Decoder Timing Table 10-20 Quadrature Decoder Timing1, 2 Characteristic Quadrature input period Quadrature input high / low period Quadrature phase period Symbol PIN PHL PPH Min 4T + 12 2T + 6 1T + 3 Max -- -- -- Unit ns ns ns See Figure 10-15 10-15 10-15 1. In the formulas listed, T = the clock cycle. For 60MHz operation, T=16.67ns. 2. Parameters listed are guaranteed by design. 56F8367 Technical Data, Rev. 3.0 156 Freescale Semiconductor Preliminary Serial Communication Interface (SCI) Timing PPH PPH PPH PPH Phase A (Input) PHL PIN PHL Phase B (Input) PHL PIN PHL Figure 10-15 Quadrature Decoder Timing 10.13 Serial Communication Interface (SCI) Timing Table 10-21 SCI Timing1 Characteristic Baud Rate2 RXD3 Pulse Width TXD4 Pulse Width Symbol BR RXDPW TXDPW Min Max (fMAX/16) 1.04/BR 1.04/BR Unit Mbps ns ns See Figure -- 0.965/BR 0.965/BR -- 10-16 10-17 1. Parameters listed are guaranteed by design. 2. fMAX is the frequency of operation of the system clock, ZCLK, in MHz, which is 60MHz for the 56F8367 device , and 40MHz for the 56F8167 device. 3. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1. 4. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1. RXD SCI receive data pin (Input) RXDPW Figure 10-16 RXD Pulse Width TXD SCI receive data pin (Input) TXDPW Figure 10-17 TXD Pulse Width 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 157 10.14 Controller Area Network (CAN) Timing Note: CAN is not available in the 56F8167 device. Table 10-22 CAN Timing1 Characteristic Baud Rate Bus Wake Up detection Symbol BRCAN T WAKEUP Min Max 1 Unit Mbps s See Figure -- 5 -- 10-18 -- 1. Parameters listed are guaranteed by design CAN_RX CAN receive data pin (Input) T WAKEUP Figure 10-18 Bus Wakeup Detection 10.15 JTAG Timing Table 10-23 JTAG Timing Characteristic TCK frequency of operation using EOnCE1 TCK frequency of operation not using EOnCE1 TCK clock pulse width TMS, TDI data set-up time TMS, TDI data hold time TCK low to TDO data valid TCK low to TDO tri-state TRST assertion time Symbol fOP fOP tPW tDS tDH tDV tTS tTRST Min DC DC 50 5 5 -- -- 2T2 Max SYS_CLK/8 SYS_CLK/4 -- -- -- 30 30 -- Unit MHz MHz ns ns ns ns ns ns See Figure 10-19 10-19 10-19 10-20 10-20 10-20 10-20 10-21 1. TCK frequency of operation must be less than 1/8 the processor rate. 2. T = processor clock period (nominally 1/60MHz) 56F8367 Technical Data, Rev. 3.0 158 Freescale Semiconductor Preliminary JTAG Timing 1/fOP tPW VIH tPW VM TCK (Input) VM = VIL + (VIH - VIL)/2 VM VIL Figure 10-19 Test Clock Input Timing Diagram TCK (Input) tDS tDH TDI TMS (Input) TDO (Output) Input Data Valid tDV Output Data Valid tTS TDO (Output) tDV TDO (Output) Output Data Valid Figure 10-20 Test Access Port Timing Diagram TRST (Input) tTRST Figure 10-21 TRST Timing Diagram 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 159 10.16 Analog-to-Digital Converter (ADC) Parameters Table 10-24 ADC Parameters Characteristic Input voltages Resolution Integral Non-Linearity1 Differential Non-Linearity Monotonicity ADC internal clock Conversion range ADC channel power-up time ADC reference circuit power-up time4 Conversion time Sample time Input capacitance Input injection current5, per pin Input injection current, total VREFH current ADC A current ADC B current Quiescent current Uncalibrated Gain Error (ideal = 1) Uncalibrated Offset Voltage Calibrated Absolute Error6 Calibration Factor 17 Calibration Factor 2 Crosstalk between channels Common Mode Voltage Signal-to-noise ratio fADIC RAD tADPU tVREF tADC tADS CADI IADI IADIT IVREFH IADCA IADCB IADCQ EGAIN VOFFSET AECAL CF1 CF2 -- Vcommon SNR 0.5 VREFL 5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Symbol VADIN RES INL DNL Min VREFL 12 -- -- Typ -- -- +/- 2.4 +/- 0.7 GUARANTEED -- -- 6 -- 6 1 5 -- -- 1.2 25 25 0 .+/- .004 +/- 27 See Figure 10-22 0.002289 -25.6 -60 (VREFH - VREFLO) / 2 64.6 5 VREFH 16 25 -- -- -- 3 20 3 -- -- 10 +/- .01 +/- 40 -- -- -- -- -- -- MHz V tAIC cycles3 ms tAIC cycles3 tAIC cycles3 pF mA mA mA mA mA A -- mV LSBs -- -- dB V db Max VREFH 12 +/- 3.2 < +1 Unit V Bits LSB2 LSB2 56F8367 Technical Data, Rev. 3.0 160 Freescale Semiconductor Preliminary Analog-to-Digital Converter (ADC) Parameters Table 10-24 ADC Parameters (Continued) Characteristic Signal-to-noise plus distortion ratio Total Harmonic Distortion Spurious Free Dynamic Range Effective Number Of Bits8 Symbol SINAD THD SFDR ENOB Min -- -- -- -- Typ 59.1 60.6 61.1 9.6 Max -- -- -- -- Unit db db db Bits 1. INL measured from Vin = .1VREFH to Vin = .9VREFH 10% to 90% Input Signal Range 2. LSB = Least Significant Bit 3. ADC clock cycles 4. Assumes each voltage reference pin is bypassed with 0.1F ceramic capacitors to ground 5. The current that can be injected or sourced from an unselected ADC signal input without impacting the performance of the ADC. This allows the ADC to operate in noisy industrial environments where inductive flyback is possible. 6. Absolute error includes the effects of both gain error and offset error. 7. Please see the 56F8300Peripheral User's Manual for additional information on ADC calibration. 8. ENOB = (SINAD - 1.76)/6.02 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 161 Figure 10-22 ADC Absolute Error Over Processing and Temperature Extremes Before and After Calibration for VDCin = 0.60V and 2.70V Note: The absolute error data shown in the graphs above reflects the effects of both gain error and offset error. The data was taken on 25 parts: three each from four processing corner lots as well as five from one nominally processed lot, each at three temperatures: -40C, 27C, and 150C (giving the 75 data points shown above), for two input DC voltages: 0.60V and 2.70V. The data indicates that for the given population of parts, calibration significantly reduced (by as much as 24%) the collective variation (spread) of the absolute error of the population. It also significantly reduced (by as much as 38%) the mean (average) of the absolute error and thereby brought it significantly closer to the ideal value of zero. Although not guaranteed, it is believed that calibration will produce results similar to those shown above for any population of parts including those which represent processing and temperature extremes. 56F8367 Technical Data, Rev. 3.0 162 Freescale Semiconductor Preliminary Equivalent Circuit for ADC Inputs 10.17 Equivalent Circuit for ADC Inputs Figure 10-23 illustrates the ADC input circuit during sample & hold. S1 and S2 are always open/closed at the same time that S3 is closed/open. When S1/S2 are closed & S3 is open, one input of the sample and hold circuit moves to VREFH - VREFH / 2, while the other charges to the analog input voltage. When the switches are flipped, the charge on C1 and C2 are averaged via S3, with the result that a single-ended analog input is switched to a differential voltage centered about VREFH - VREFH / 2. The switches switch on every cycle of the ADC clock (open one-half ADC clock, closed one-half ADC clock). Note that there are additional capacitances associated with the analog input pad, routing, etc., but these do not filter into the S/H output voltage, as S1 provides isolation during the charge-sharing phase. One aspect of this circuit is that there is an on-going input current, which is a function of the analog input voltage, VREF and the ADC clock frequency. Analog Input 3 S1 S3 1 2 VREFH - VREFH / 2 S2 C2 4 C1 S/H C1 = C2 = 1pF 1. 2. 3. 4. Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling; 1.8pf Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing; 2.04pf Equivalent resistance for the ESD isolation resistor and the channel select mux; 500 ohms Sampling capacitor at the sample and hold circuit. Capacitor C1 is normally disconnected from the input and is only connected to it at sampling time; 1pf Figure 10-23 Equivalent Circuit for A/D Loading 10.18 Power Consumption This section provides additional detail which can be used to optimize power consumption for a given application. Power consumption is given by the following equation: Total power = A: +B: +C: +D: +E: internal [static component] internal [state-dependent component] internal [dynamic component] external [dynamic component] external [static] A, the internal [static component], is comprised of the DC bias currents for the oscillator, leakage current, PLL, and voltage references. These sources operate independently of processor state or operating frequency. B, the internal [state-dependent component], reflects the supply current required by certain on-chip resources only when those resources are in use. These include RAM, Flash memory and the ADCs. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 163 C, the internal [dynamic component], is classic C*V2*F CMOS power dissipation corresponding to the 56800E core and standard cell logic. D, the external [dynamic component], reflects power dissipated on-chip as a result of capacitive loading on the external pins of the chip. This is also commonly described as C*V2*F, although simulations on two of the IO cell types used on the device reveal that the power-versus-load curve does have a non-zero Y-intercept. Table 10-25 I/O Loading Coefficients at 10MHz Intercept PDU08DGZ_ME PDU04DGZ_ME 1.3 1.15mW Slope 0.11mW / pF 0.11mW / pF Power due to capacitive loading on output pins is (first order) a function of the capacitive load and frequency at which the outputs change. Table 10-20 provides coefficients for calculating power dissipated in the IO cells as a function of capacitive load. In these cases: TotalPower = ((Intercept +Slope*Cload)*frequency/10MHz) where: * * * Summation is performed over all output pins with capacitive loads TotalPower is expressed in mW Cload is expressed in pF Because of the low duty cycle on most device pins, power dissipation due to capacitive loads was found to be fairly low when averaged over a period of time. The one possible exception to this is if the chip is using the external address and data buses at a rate approaching the maximum system rate. In this case, power from these buses can be significant. E, the external [static component], reflects the effects of placing resistive loads on the outputs of the device. Sum the total of all V2/R or IV to arrive at the resistive load contribution to power. Assume V = 0.5 for the purposes of these rough calculations. For instance, if there is a total of 8 PWM outputs driving 10mA into LEDs, then P = 8*.5*.01 = 40mW. In previous discussions, power consumption due to parasitics associated with pure input pins is ignored, as it is assumed to be negligible. 56F8367 Technical Data, Rev. 3.0 164 Freescale Semiconductor Preliminary 56F8367 Package and Pin-Out Information Part 11 Packaging Note: The 160 Map Ball Grid Array is not available in the 56F8167 device. 11.1 56F8367 Package and Pin-Out Information This section contains package and pin-out information for the 56F8367. This device comes in a 160-pin Low-profile Quad Flat Pack (LQFP) and 160 Map Ball Grid Array. Figure 11-1 shows the package lay-out for the 160-pin LQFP, and Figure 11-2 for the160 Map Ball Grid Array. Figure 11-5 shows the mechanical parameters for the LQFP package and Figure 11-3 for the MAPBGA, Table 11-1 lists the pin-out for the 160-pin LQFP and Table 11-2 lists the pin-out for the 160 MAPBGA. EMI_MODE HOME0 INDEX0 PHASEB0 PHASEA0 A0 D15 D14 D13 D12 D11 MOSI0 MISO0 SCLK0 SS0 VCAP2 CAN_RX CAN_TX VPP1 TDO TDI TMS TCK TRST TC1 VDD_IO TC0 TD3 TD2 TD1 TD0 ISA2 ISA1 ISA0 VSS EXTBOOT VDD_IO VPP2 CLKO TXD0 RXD0 PHASEA1 PHASEB1 INDEX1 HOME1 A1 A2 A3 A4 A5 VCAP4 VDD_IO A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 VSS D7 D8 D9 VDD_IO D10 GPIOB0 GPIOB1 GPIOB2 GPIOB3 GPIOB4 PWMB0 PWMB1 PWMB2 Orientation Mark Pin 1 121 ANB7 ANB6 ANB5 VSS ANB4 ANB3 ANB2 ANB1 ANB0 VSSA_ADC VDDA_ADC VREFH VREFP VREFMID VREFN VREFLO TEMP_SENSE ANA7 ANA6 ANA5 ANA4 ANA3 ANA2 ANA1 ANA0 CLKMODE RESET RSTO VDD_IO VCAP3 EXTAL XTAL VDDA_OSC_PLL OCR_DIS D6 D5 D4 FAULTA3 D3 FAULTA2 FAULTA1 41 81 D2 FAULTA0 PWMA5 * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. Freescale Semiconductor Preliminary VDD_IO PWMB3 PWMB4 PWMB5 GPIOB5 GPIOB6 GPIOB7 TXD1 RXD1 WR RD PS DS GPIOD0 GPIOD1 GPIOD2 GPIOD3 GPIOD4 GPIOD5 ISB0 VCAP1 ISB1 ISB2 IRQA IRQB FAULTB0 FAULTB1 FAULTB2 D0 D1 FAULTB3 PWMA0 VSS PWMA1 PWMA2 VDD_IO Figure 11-1 Top View, 56F8367 160-Pin LQFP Package 56F8367 Technical Data, Rev. 3.0 165 PWMA3 PWMA4 VSS VSS Table 11-1 56F8367 160-Pin LQFP Package Identification by Pin Number Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Signal Name VDD_IO VPP2 CLKO TXD0 RXD0 PHASEA1 PHASEB1 INDEX1 HOME1 A1 A2 A3 A4 A5 VCAP4* VDD_IO A6 A7 A8 A9 A10 A11 A12 A13 A14 Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Signal Name VSS VDD_IO PWMB3 PWMB4 PWMB5 GPIOB5 GPIOB6 GPIOB7 TXD1 RXD1 WR RD PS DS GPIOD0 GPIOD1 GPIOD2 GPIOD3 GPIOD4 GPIOD5 ISB0 VCAP1* ISB1 ISB2 IRQA Pin No. 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 Signal Name PWMA5 FAULTA0 D2 FAULTA1 FAULTA2 D3 FAULTA3 D4 D5 D6 OCR_DIS VDDA_OSC_PLL XTAL EXTAL VCAP3* VDD_IO RSTO RESET CLKMODE ANA0 ANA1 ANA2 ANA3 ANA4 ANA5 Pin No. 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 Signal Name ANB5 ANB6 ANB7 EXTBOOT VSS ISA0 ISA1 ISA2 TD0 TD1 TD2 TD3 TC0 VDD_IO TC1 TRST TCK TMS TDI TDO VPP1 CAN_TX CAN_RX VCAP2* SS0 * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. 56F8367 Technical Data, Rev. 3.0 166 Freescale Semiconductor Preliminary 56F8367 Package and Pin-Out Information Table 11-1 56F8367 160-Pin LQFP Package Identification by Pin Number (Continued) Pin No. 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Signal Name A15 VSS D7 D8 D9 VDD_IO D10 GPIOB0 GPIOB1 GPIOB2 GPIOB3 GPIOB4 PWMB0 PWMB1 PWMB2 Pin No. 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Signal Name IRQB FAULTB0 FAULTB1 FAULTB2 D0 D1 FAULTB3 PWMA0 VSS PWMA1 PWMA2 VDD_IO PWMA3 PWMA4 VSS Pin No. 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 Signal Name ANA6 ANA7 TEMP_SENSE VREFLO VREFN VREFMID VREFP VREFH VDDA_ADC VSSA_ADC ANB0 ANB1 ANB2 ANB3 ANB4 Pin No. 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 Signal Name SCLK0 MISO0 MOSI0 D11 D12 D13 D14 D15 A0 PHASEA0 PHASEB0 INDEX0 HOME0 EMI_MODE VSS 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 167 1 A 2 3 4 5 6 7 8 9 10 11 12 13 14 INDEX0 PHASEA0 D15 D12 D11 SCLK0 VPP1 TMS TC0 TD1 ISA0 ANB7 ANB5 ANB4 B TXD0 EMI_ HOME0 PHASEB0 MODE D13 MOSI0 CAN_RX TDI TC1 TD0 EXTBOOT ANB6 ANB3 ANB1 C PHASEA1 VPP2 A0 D14 ISA1 ANB2 ANB0 VDDA_ADC D PHASEB1 RXD0 HOME1 MISO0 SS0 CAN_TX TDO TCK TRST TD2 ISA2 VSSA_ADC VREFP VREFH E HOME1 INDEX1 A1 A2 VDD_IO VSS VSS VCAP2 VDD_IO TD3 TEMP_ SENSE VREFLO ANA7 VREFMID F A4 A3 A5 VDD_IO VDD_IO ANA4 ANA3 VREFN G A6 A8 A7 VCAP4 VSS ANA2 ANA0 ANA6 H A9 A10 A12 A11 VCAP3 CLKO MODE ANA1 ANA5 J A13 A14 A15 VSS VSS EXTAL RSTO RESET K D7 D9 D8 D10 VDD_IO GPIOD2 VDD_IO VCAP1 IRQA VDD_IO VSS XTAL VDDA_ OSC_PLL OCR_DIS L GPIOB0 GPIOB2 GPIOB1 WR DS GPIOD1 GPIOD5 ISB1 FAULTB1 FAULTB2 D6 D5 D3 D4 M GPIOB3 GPIOB4 PWMB5 GPIOB7 PWMA0 PWMA3 FAULTA2 FAULTA3 N PWMB0 PWMB2 PWMB3 GPIOB5 RXD1 PS GPIOD3 ISB0 FAULTB0 D1 PWMA2 PWMA5 FAULTA0 FAULTA1 P PWMB1 PWMB4 GPIOB6 TXD1 RD GPIOD0 GPIOD4 ISB2 IRQB D0 FAULTB3 PWMA1 PWMA4 D2 Figure 11-2 Top View, 56F8367 160-Pin MAPBGA Package 56F8367 Technical Data, Rev. 3.0 168 Freescale Semiconductor Preliminary 56F8367 Package and Pin-Out Information Table 11-2 56F8367 -160 MAPBGA Package Identification by Pin Number Ball No. F4 C2 D3 B1 D2 C1 D1 E2 D3 E3 E4 F2 F1 F3 G4 K5 G1 G3 G2 H1 H2 H4 H3 J1 J2 Signal Name VDD_IO VPP2 CLKO TXD0 RXD0 PHASEA1 PHASEB1 INDEX1 HOME1 A1 A2 A3 A4 A5 VCAP4* VDD_IO A6 A7 A8 A9 A10 A11 A12 A13 A14 Ball No. K11 K7 N3 P2 M3 N4 P3 M4 P4 N5 L4 P5 N6 L5 P6 L6 K6 N7 P7 L7 N8 K8 L8 P8 K9 Signal Name VSS VDD_IO PWMB3 PWMB4 PWMB5 GPIOB5 GPIOB6 GPIOB7 TXD1 RXD1 WR RD PS DS GPIOD0 GPIOD1 GPIOD2 GPIOD3 GPIOD4 GPIOD5 ISB0 VCAP1* ISB1 ISB2 IRQA Ball No. N12 N13 P14 N14 M13 L13 M14 L14 L12 L11 K14 K13 K12 J12 H11 K10 J13 J14 H12 G13 H13 G12 F13 F12 H14 Signal Name PWMA5 FAULTA0 D2 FAULTA1 FAULTA2 D3 FAULTA3 D4 D5 D6 OCR_DIS VDDA_OSC_PLL XTAL EXTAL VCAP3* VDD_IO RSTO RESET CLKMODE ANA0 ANA1 ANA2 ANA3 ANA4 ANA5 Ball No. A13 B12 A12 B11 J11 A11 C11 D11 B10 A10 D10 E10 A9 F11 B9 D9 D8 A8 B8 D7 A7 D6 B7 E8 D5 Signal Name ANB5 ANB6 ANB7 EXTBOOT VSS ISA0 ISA1 ISA2 TD0 TD1 TD2 TD3 TC0 VDD_IO TC1 TRST TCK TMS TDI TDO VPP1 CAN_TX CAN_RX VCAP2* SS0 * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 169 Table 11-2 56F8367 -160 MAPBGA Package Identification by Pin Number (Continued) Ball No. J3 J4 K1 K3 K2 E5 K4 L1 L3 L2 M1 M2 N1 P1 N2 Signal Name A15 VSS D7 D8 D9 VDD_IO D10 GPIOB0 GPIOB1 GPIOB2 GPIOB3 GPIOB4 PWMB0 PWMB1 PWMB2 Ball No. P9 N9 L9 L10 P10 N10 P11 M11 G11 P12 N11 E9 M12 P13 E7 Signal Name IRQB FAULTB0 FAULTB1 FAULTB2 D0 D1 FAULTB3 PWMA0 VSS PWMA1 PWMA2 VDD_IO PWMA3 PWMA4 VSS Ball No. G14 E13 E11 E12 F14 E14 D13 D14 C14 D12 C13 B14 C12 B13 A14 Signal Name ANA6 ANA7 TEMP_SENSE VREFLO VREFN VREFMID VREFP VREFH VDDA_ADC VSSA_ADC ANB0 ANB1 ANB2 ANB3 ANB4 Ball No. A6 D4 B6 A5 A4 B5 C4 A3 C3 A2 B4 A1 B3 B2 E6 Signal Name SCLK0 MISO0 MOSI0 D11 D12 D13 D14 D15 A0 PHASEA0 PHASEB0 INDEX0 HOME0 EMI_MODE VSS 56F8367 Technical Data, Rev. 3.0 170 Freescale Semiconductor Preliminary 56F8367 Package and Pin-Out Information X Y D LASER MARK FOR PIN 1 IDENTIFICATION IN THIS AREA M K E NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSION b IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER, PARALLEL TO DATUM PLANE Z. 4. DATUM Z (SEATING PLANE) IS DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS. 5. PARALLELISM MEASUREMENT SHALL EXCLUDE ANY EFFECT OF MARK ON TOP SURFACE OF PACKAGE. 0.20 13X e METALIZED MARK FOR PIN 1 IDENTIFICATION IN THIS AREA A B C S 14 13 12 11 10 9 6 5 4 3 2 1 MILLIMETERS DIM MIN MAX A 1.32 1.75 A1 0.27 0.47 A2 1.18 REF b 0.35 0.65 D 15.00 BSC E 15.00 BSC e 1.00 BSC S 0.50 BSC S 13X D E F G H J K L M N 160X 5 A A2 0.30 Z e A1 Z 4 0.15 Z ROTATED 90 CLOCKWISE DETAIL K 3 160X P b 0.30 Z X Y 0.10 Z VIEW M-M CASE 1268-01 ISSUE O DATE 04/06/98 Please see http://www.freescale.com for the most current mechanical drawing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 171 Figure 11-3 160 MAPBGA Mechanical Information 11.2 56F8167 Package and Pin-Out Information This section contains package and pin-out information for the 56F8167. This device comes in a 160-pin Low-profile Quad Flat Pack (LQFP). Figure 11-4 shows the package outline for the 160-pin LQFP, Figure 11-5 shows the mechanical parameters for this package, and Table 11-3 lists the pin-out for the 160-pin LQFP. EMI_MODE HOME0 INDEX0 PHASEB0 PHASEA0 A0 D15 D14 D13 D12 D11 MOSI0 MISO0 SCLK0 SS0 VCAP2* NC NC VPP1 TDO TDI TMS TCK TRST TC1 VDD_IO TC0 GPIOE13 GPIOE12 GPIOE11 GPIOE10 GPIOC10 GPIOC9 GPIOC8 VSS EXTBOOT VDD_IO VPP2 CLKO TXD0 RXD0 SCLK1 MOSI1 MISO1 SS1 A1 A2 A3 A4 A5 VCAP4* VDD_IO A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 VSS D7 D8 D9 VDD_IO D10 GPIOB0 GPIOB1 GPIOB2 GPIOB3 GPIOB4 PWMB0 PWMB1 PWMB2 Orientation Mark Pin 1 121 ANB7 ANB6 ANB5 VSS ANB4 ANB3 ANB2 ANB1 ANB0 VSSA_ADC VDDA_ADC VREFH VREFP VREFMID VREFN VREFLO NC ANA7 ANA6 ANA5 ANA4 ANA3 ANA2 ANA1 ANA0 CLKMODE RESET RSTO VDD_IO VCAP3* EXTAL XTAL VDDA_OSC_PLL OCR_DIS D6 D5 D4 NC D3 NC NC D2 NC NC 41 81 VDD_IO PWMB3 PWMB4 PWMB5 GPIOB5 GPIOB6 GPIOB7 TXD1 RXD1 WR RD PS DS GPIOD0 GPIOD1 GPIOD2 GPIOD3 GPIOD4 GPIOD5 ISB0 VCAP1* ISB1 ISB2 IRQA IRQB FAULTB0 FAULTB1 FAULTB2 D0 D1 FAULTB3 NC VSS NC NC VDD_IO * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE. VSS Figure 11-4 Top View, 56F8167 160-Pin LQFP Package 56F8367 Technical Data, Rev. 3.0 172 Freescale Semiconductor Preliminary NC NC VSS 56F8167 Package and Pin-Out Information Table 11-3 56F8167 160-Pin LQFP Package Identification by Pin Number Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Signal Name VDD_IO VPP2 CLKO TXD0 RXD0 SCLK1 MOSI1 MISO1 SS1 A1 A2 A3 A4 A5 VCAP4* VDD_IO A6 A7 A8 A9 A10 A11 A12 A13 A14 Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Signal Name VSS VDD_IO PWMB3 PWMB4 PWMB5 GPIOB5 GPIOB6 GPIOB7 TXD1 RXD1 WR RD PS DS GPIOD0 GPIOD1 GPIOD2 GPIOD3 GPIOD4 GPIOD5 ISB0 VCAP1* ISB1 ISB2 IRQA Pin No. 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 Signal Name NC NC D2 NC NC D3 NC D4 D5 D6 OCR_DIS VDDA_OSC_PLL XTAL EXTAL VCAP3* VDD_IO RSTO RESET CLKMODE ANA0 ANA1 ANA2 ANA3 ANA4 ANA5 Pin No. 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 Signal Name ANB5 ANB6 ANB7 EXTBOOT VSS GPIOC8 GPIOC9 GPIOC10 GPIOE10 GPIOE11 GPIOE12 GPIOE13 TC0 VDD_IO TC1 TRST TCK TMS TDI TDO VPP1 NC NC VCAP2* SS0 * When the on-chip regulator is disabled, these four pins become 2.5V VDD_CORE Please see http://www.freescale.com for the most current mechanical drawing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 173 Table 11-3 56F8167 160-Pin LQFP Package Identification by Pin Number (Continued) Pin No. 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Signal Name A15 VSS D7 D8 D9 VDD_IO D10 GPIOB0 GPIOB1 GPIOB2 GPIOB3 GPIOB4 PWMB0 PWMB1 PWMB2 Pin No. 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Signal Name IRQB FAULTB0 FAULTB1 FAULTB2 D0 D1 FAULTB3 NC VSS NC NC VDD_IO NC NC VSS Pin No. 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 Signal Name ANA6 ANA7 NC VREFLO VREFN VREFMID VREFP VREFH VDDA_ADC VSSA_ADC ANB0 ANB1 ANB2 ANB3 ANB4 Pin No. 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 Signal Name SCLK0 MISO0 MOSI0 D11 D12 D13 D14 D15 A0 PHASEA0 PHASEB0 INDEX0 HOME0 EMI_MODE VSS 56F8367 Technical Data, Rev. 3.0 174 Freescale Semiconductor Preliminary 56F8167 Package and Pin-Out Information 160X 0.20 C A-B D D 6 D 2 GG D c b (b) A B SECTION G-G NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DATUMS A, B, AND D TO BE DETERMINED WHERE THE LEADS EXIT THE PLASTIC BODY AT DATUM PLANE H. 4. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25mm PER SIDE. DIMENSIONS D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE DIMENSIONS INCLUDING MOLD MISMATCH. 5. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE MAXIMUM b DIMENSION BY MORE THAN 0.08mm. DAMBAR CAN NOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN A PROTRUSION AND AN ADJACENT LEAD IS 0.07mm. 6. EXACT SHAPE OF CORNERS MAY VARY. D1 2 D1 DETAIL F 4X 0.20 H A-B D 156X C SEATING PLANE 4X e e/2 160X E1 2 E 2 0.08 C e M MILLIMETERS DIM MIN MAX A --1.60 A1 0.05 0.15 A2 1.35 1.45 b 0.17 0.27 b1 0.17 0.23 c 0.09 0.20 c1 0.09 0.16 D 26.00 BSC D1 24.00 BSC e 0.50 BSC E 26.00 BSC E1 24.00 BSC L 0.45 0.75 L1 1.00 REF R1 0.08 --R2 0.08 0.20 S 0.20 -- 0 7 1 0 --2 11 13 3 11 13 0.08 2 1 A2 A R1 R2 H C A-B D 3 A1 S L (L1) DETAIL F 0.25 GAGE PLANE Figure 11-5 160-pin LQFP Mechanical Information Please see http://www.freescale.com for the most current mechanical drawing. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 175 E1 E c1 Part 12 Design Considerations 12.1 Thermal Design Considerations An estimation of the chip junction temperature, TJ, can be obtained from the equation: TJ = TA + (RJ x PD) where: TA = Ambient temperature for the package (oC) RJ = Junction-to-ambient thermal resistance (oC/W) PD = Power dissipation in the package (W) The junction-to-ambient thermal resistance is an industry-standard value that provides a quick and easy estimation of thermal performance. Unfortunately, there are two values in common usage: the value determined on a single-layer board and the value obtained on a board with two planes. For packages such as the PBGA, these values can be different by a factor of two. Which value is closer to the application depends on the power dissipated by other components on the board. The value obtained on a single-layer board is appropriate for the tightly packed printed circuit board. The value obtained on the board with the internal planes is usually appropriate if the board has low-power dissipation and the components are well separated. When a heat sink is used, the thermal resistance is expressed as the sum of a junction-to-case thermal resistance and a case-to-ambient thermal resistance: RJ = RJC + RC where: RJA RJC RCA = Package junction-to-ambient thermal resistance C/W = Package junction-to-case thermal resistance C/W = Package case-to-ambient thermal resistance C/W R JC is device-related and cannot be influenced by the user. The user controls the thermal environment to change the case-to-ambient thermal resistance, R CA . For instance, the user can change the size of the heat sink, the air flow around the device, the interface material, the mounting arrangement on printed circuit board, or change the thermal dissipation on the printed circuit board surrounding the device. To determine the junction temperature of the device in the application when heat sinks are not used, the Thermal Characterization Parameter (JT) can be used to determine the junction temperature with a measurement of the temperature at the top center of the package case using the following equation: TJ = TT + (JT x PD) where: TT = Thermocouple temperature on top of package (oC) JT = Thermal characterization parameter (oC)/W PD = Power dissipation in package (W) 56F8367 Technical Data, Rev. 3.0 176 Freescale Semiconductor Preliminary Electrical Design Considerations The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire. When heat sink is used, the junction temperature is determined from a thermocouple inserted at the interface between the case of the package and the interface material. A clearance slot or hole is normally required in the heat sink. Minimizing the size of the clearance is important to minimize the change in thermal performance caused by removing part of the thermal interface to the heat sink. Because of the experimental difficulties with this technique, many engineers measure the heat sink temperature and then back-calculate the case temperature using a separate measurement of the thermal resistance of the interface. From this case temperature, the junction temperature is determined from the junction-to-case thermal resistance. 12.2 Electrical Design Considerations CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Use the following list of considerations to assure correct operation: * * Provide a low-impedance path from the board power supply to each VDD pin on the hybrid controller, and from the board ground to each VSS (GND) pin The minimum bypass requirement is to place six 0.01-0.1F capacitors positioned as close as possible to the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better performance tolerances. Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND) pins are less than 0.5 inch per capacitor lead Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and VSS Bypass the VDD and VSS layers of the PCB with approximately 100F, preferably with a high-grade capacitor such as a tantalum capacitor Because the device's output signals have fast rise and fall times, PCB trace lengths should be minimal * * * * 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 177 * Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance. This is especially critical in systems with higher capacitive loads that could create higher transient currents in the VDD and VSS circuits. Take special care to minimize noise levels on the VREF, VDDA and VSSA pins Designs that utilize the TRST pin for JTAG port or EOnCE module functionality (such as development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as well as a means to assert TRST independently of RESET. Designs that do not require debugging functionality, such as consumer products, should tie these pins together. Because the Flash memory is programmed through the JTAG/EOnCE port, the designer should provide an interface to this port to allow in-circuit Flash programming * * * 12.3 Power Distribution and I/O Ring Implementation Figure 12-1 illustrates the general power control incorporated in the 56F8367/56F8167. This chip contains two internal power regulators. One of them is powered from the VDDA_OSC_PLL pin and cannot be turned off. This regulator controls power to the internal clock generation circuitry. The other regulator is powered from the VDD_IO pins and provides power to all of the internal digital logic of the core, all peripherals and the internal memories. This regulator can be turned off, if an external VDD_CORE voltage is externally applied to the VCAP pins. In summary, the entire chip can be supplied from a single 3.3 volt supply if the large core regulator is enabled. If the regulator is not enabled, a dual supply 3.3V/2.5V configuration can also be used. Notes: * * * Flash, RAM and internal logic are powered from the core regulator output VPP1 and VPP2 are not connected in the customer system All circuitry, analog and digital, shares a common VSS bus VDDA_OSC_PLL VDD VCAP I/O CORE OSC VSS VSSA_ADC ADC VDDA_ADC VREFH VREFP VREFMID VREFN VREFLO REG REG Figure 12-1 Power Management 56F8367 Technical Data, Rev. 3.0 178 Freescale Semiconductor Preliminary Power Distribution and I/O Ring Implementation Part 13 Ordering Information Table 13-1 lists the pertinent information needed to place an order. Consult a Freescale Semiconductor sales office or authorized distributor to determine availability and to order parts. Table 13-1 Ordering Information Part MC56F8367 MC56F8167 Supply Voltage 3.0-3.6 V 3.0-3.6 V Package Type Low-Profile Quad Flat Pack (LQFP) Low-Profile Quad Flat Pack (LQFP) Pin Count 160 160 Frequency (MHz) 60 40 Ambient Temperature Range -40 to + 105 C -40 to + 105 C Order Number MC56F8367VPY60 MC56F8167VPY MC56F8367 MC56F8367 MC56F8167 MC56F8367 3.0-3.6 V 3.0-3.6 V 3.0-3.6 V 3.0-3.6 V Low-Profile Quad Flat Pack (LQFP) Low-Profile Quad Flat Pack (LQFP) Low-Profile Quad Flat Pack (LQFP) Mold Array Process Ball Grid Array (MAPBGA) 160 160 160 160 60 60 40 60 -40 to + 105 C -40 to + 125 C -40 to + 105 C -40 to + 105 C MC56F8367VPYE* MC56F8367MPYE* MC56F8167VPYE* MC56F8367VVF* *This package is RoHS compliant. 56F8367 Technical Data, Rev. 3.0 Freescale Semiconductor Preliminary 179 How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064, Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. This product incorporates SuperFlash(R) technology licensed from SST. (c) Freescale Semiconductor, Inc. 2005. All rights reserved. MC56F8367 Rev. 3.0 09/2005 |
Price & Availability of MC56F8367VPY60 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |