 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| User's Manual SM+ System Simulator Operation Target Device SM+ for V850 Ver. 2.00 SM+ for 78K0 Ver. 1.01 SM+ for 78K0S Ver. 1.01 Document No. U17246EJ2V0UM00 (2nd edition) Date Published November 2004 CP(K) (c) NEC Electronics Corporation 2004 Printed in Japan [MEMO] 2 User's Manual U17246EJ2V0UM Pentium is a trademark of Intel Corporation. Windows and WindowsNT are either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. User's Manual U17246EJ2V0UM 3 * The information in this document is current as of November, 2004. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 4 User's Manual U17246EJ2V0UM Regional Information Some information contained in this document may vary from country to country. Before using any NEC Electronics product in your application, pIease contact the NEC Electronics office in your country to obtain a list of authorized representatives and distributors. They will verify: * * * * * Device availability Ordering information Product release schedule Availability of related technical literature Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) Network requirements * In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. [GLOBAL SUPPORT] http://www.necel.com/en/support/support.html NEC Electronics America, Inc. (U.S.) Santa Clara, California Tel: 408-588-6000 800-366-9782 NEC Electronics (Europe) GmbH Duesseldorf, Germany Tel: 0211-65030 * Sucursal en Espana NEC Electronics Hong Kong Ltd. Hong Kong Tel: 2886-9318 NEC Electronics Hong Kong Ltd. Seoul Branch Seoul, Korea Tel: 02-558-3737 Madrid, Spain Tel: 091-504 27 87 * Succursale Francaise Velizy-Villacoublay, France Tel: 01-30-67 58 00 * Filiale Italiana NEC Electronics Shanghai Ltd. Shanghai, P.R. China Tel: 021-5888-5400 Milano, Italy Tel: 02-66 75 41 * Branch The Netherlands NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 Eindhoven, The Netherlands Tel: 040-244 58 45 * Tyskland Filial NEC Electronics Singapore Pte. Ltd. Novena Square, Singapore Tel: 6253-8311 Taeby, Sweden Tel: 08-63 80 820 * United Kingdom Branch Milton Keynes, UK Tel: 01908-691-133 J04.1 User's Manual U17246EJ2V0UM 5 PREFACE Target Readers This manual is intended for user engineers who design and develop application systems of the V850 Series, 78K0 Series and 78K0S Series. Purpose This manual is intended for users to understand the functions of the SM+ in the organization below. Organization This manual consists of the following chapters: * OVERVIEW * INSTALLATION * STARTING AND TERMINATING * ASSOCIATION WITH PM+ * DEBUG FUNCTION * SIMULATION FUNCTION * WINDOW REFERENCE * COMMAND REFERENCE How to Use This Manual It is assumed that the readers of this manual have general knowledge of electrical engineering, logic circuits, microcontrollers, C language, and assemblers. For information on functions the windows and dialog boxes Read CHAPTER 7 WINDOW REFERENCE. For information on functions the command functions Read CHAPTER 8 COMMAND REFERENCE. For information on the meanings and causes of messages: Read APPENDIX D MESSAGES. 6 User's Manual U17246EJ2V0UM Related Documents: When using this manual, also refer to the following documents. Some related documents may be preliminary versions. Note, however, that whether a related document is preliminary is not indicated in this document. Documents related to 78K Series development tools (User's Manual) Document Name CC78K0 Ver. 3.70 C Compiler Operation Language CC78K0S C Compiler Operation Language RA78K0 Ver. 3.80 Assembler Package Operation Language Structured Assembly Language RA78K0S Assembler Package Operation Language Structured Assembly Language SM+ System Simulator Operation User Open Interface Specifications SM78K Series Ver. 2.52 System Simulator ID78K0-NS Ver. 2.52 Integrated Debugger ID78K0S-NS Ver. 2.52 Integrated Debugger ID78K0-QB Ver. 2.81 Integrated Debugger ID78K0S-QB Ver. 2.81 Integrated Debugger PM+ Ver. 6.00 Project Manager Operation Operation Operation Operation Operation Document No. U17201E U17200E - - U17199E U17198E U17197E - - - This manual U17247E U16768E U16488E U16584E U16996E U17287E U17178E User's Manual U17246EJ2V0UM 7 Documents related to V850 Series development tools (User's Manual) Document Name CA850 Ver. 3.00 C Compiler Package Operation C Language Assembly Language Link Directives ID850 Ver. 2.50 Integrated Debugger ID850NW Ver. 2.51 Integrated Debugger ID850NWC Ver. 2.51 Integrated Debugger ID850QB Ver. 2.80 Integrated Debugger SM+ System Simulator Operation Operation Operation Operation Operation User Open Interface Specifications SM850 Ver. 2.50 System Simulator SM850 Ver. 2.00 or later System Simulator RX850 Ver. 3.13 or later Real-Time OS Operation External Part User Open Interface Specifications Basics Installation Technical RX850 Pro Ver. 3.13 Real-Time OS Basics Installation Technical RD850 Ver. 3.01 Task Debugger RD850 Pro Ver. 3.01 Task Debugger AZ850 Ver. 3.20 System Performance Analyzer PG-FP4 Flash Memory Programmer TW850 Ver. 2.00 Performance Analysis Tuning Tool PM+ Ver. 6.00 Project Manager Document No. U17293E U17291E U17292E U17294E U16217E U16454E U16525E U16973E This manual U17247E U16218E U14873E U13430E U13410E U13431E U13773E U13774E U13772E U13737E U13916E U14410E U15260E U17421E U17178E 8 User's Manual U17246EJ2V0UM CONTENTS CHAPTER 1 OVERVIEW ... 19 1. 1 Features ... 20 1. 2 System Configuration ... 21 1. 2. 1 Example of system configuration ... 21 1. 2. 2 Internal configuration ... 21 1. 3 Operating Environment ... 22 1. 3. 1 Hardware environment ... 22 1. 3. 2 Software environment ... 22 1. 4 Cautions During Debugging ... 23 1. 4. 1 When performing source level debugging ... 23 CHAPTER 2 INSTALLATION ... 24 2. 1 Installing ... 24 2. 2 Uninstalling ... 24 CHAPTER 3 STARTING AND TERMINATING ... 25 3. 1 Startup Option and Argument Specification ... 26 3. 1. 1 Specification method ... 26 3. 1. 2 Specification format and options ... 27 3. 2 Starting ... 29 3. 3 Terminating ... 30 CHAPTER 4 ASSOCIATION WITH PM+ ... 31 4. 1 Setting Build Mode ... 32 4. 2 Registering Debugger to PM+ Project ... 33 4. 2. 1 Selecting debugger ... 33 4. 2. 2 Downloading multiple load module files [V850] ... 33 4. 3 To Start SM+ from PM+ ... 34 4. 3. 1 Restoring debugging environment ... 34 4. 4 Auto Load ... 35 4. 4. 1 Auto load by correcting source code ... 35 4. 4. 2 Auto load by starting debugger ... 35 CHAPTER 5 DEBUG FUNCTION ... 36 5. 1 Setting Debugging Environment ... 37 5. 1. 1 Setting operating environment ... 37 5. 1. 2 Setting option ... 37 5. 1. 3 Setting mapping ... 37 5. 2 Download Function, Upload Function ... 39 5. 2. 1 Download ... 39 5. 2. 2 Upload ... 40 5. 3 Source Display, Disassemble Display Function ... 41 5. 3. 1 Source display ... 41 5. 3. 2 Disassemble display ... 41 5. 3. 3 Mixed display mode (Source window) ... 42 5. 3. 4 Convert symbol (Symbol to Address) ... 43 5. 4 Break Function ... 44 5. 4. 1 Break Types ... 44 5. 4. 2 Breakpoint setting ... 45 5. 4. 3 Setting breaks to variables ... 46 5. 5 Program Execution Function ... 47 5. 6 Watch Function ... 49 5. 6. 1 Displaying and changing data values ... 49 5. 6. 2 Displaying and changing local variable values ... 50 5. 6. 3 Registering and deleting watch data ... 50 5. 6. 4 Changing watch data ... 51 5. 6. 5 Temporarily displaying and changing data values ... 51 5. 6. 6 Callout watch function ... 52 5. 6. 7 Stack trace display function ... 52 User's Manual U17246EJ2V0UM 9 5. 7 Memory Manipulation Function ... 53 5. 7. 1 Displaying and changing memory contents ... 53 5. 7. 2 Filling, copying, and comparing memory contents ... 53 5. 7. 3 Modifying memory contents (DMM function) ... 54 5. 8 Register Manipulation Function ... 55 5. 8. 1 Displaying and changing register contents ... 55 5. 8. 2 Displaying and changing IOR/SFR contents ... 56 5. 8. 3 Displaying and changing I/O port contents ... 56 5. 9 Timer Function ... 57 5. 9. 1 Timer event conditions ... 57 5. 9. 2 Run-Break event ... 57 5. 10 Trace Function ... 58 5. 10. 1 Trace memory ... 58 5. 10. 2 Checking trace data ... 59 5. 10. 3 Mixed display mode (Trace window) ... 59 5. 10. 4 Tracer Operation ... 60 5. 10. 5 Setting conditional trace ... 61 5. 11 Coverage Measurement Function ... 62 5. 11. 1 Coverage measurement ... 62 5. 11. 2 Selecting coverage range [V850] ... 62 5. 11. 3 Coverage result display ... 63 5. 11. 4 Measuring and displaying coverage efficiency ... 63 5. 12 Event Function ... 65 5. 12. 1 Using event function ... 65 5. 12. 2 Creating events ... 66 5. 12. 3 Setting various event conditions ... 66 5. 12. 4 Number of enabled events for each event condition ... 68 5. 12. 5 Managing events ... 69 5. 13 Snapshot Function ... 70 5. 13. 1 Snapshot event conditions ... 70 5. 13. 2 Snap data ... 70 5. 14 Stub Function ... 71 5. 14. 1 Setting stubevent conditions ... 71 5. 14. 2 Flow of stub function ... 72 5. 15 RAM Sampling Function ... 73 5. 16 Load/Save Function ... 74 5. 16. 1 Debugging environment (project file) ... 74 5. 16. 2 Window display information (view file) ... 77 5. 16. 3 Window setting information (setting file) ... 78 5. 17 Functions Common to Each Window ... 79 5. 17. 1 Active status and static status ... 79 5. 17. 2 Jump function ... 80 5. 17. 3 Trace result with linking window ... 82 5. 17. 4 Drag & drop function ... 83 CHAPTER 6 SIMULATION FUNCTION ... 85 6. 1 Pin I/O Function ... 86 6. 1. 1 Pin input ... 86 6. 1. 2 Pin output ... 87 6. 1. 3 Pin selection ... 87 6. 1. 4 Data search ... 88 6. 1. 5 Signal data files (*.wvi, *.wvo) ... 88 6. 2 Standard I/O Function ... 92 6. 2. 1 Standard I/O and File I/O Usage Procedure ... 93 6. 2. 2 Load module creation procedure ... 94 6. 2. 3 GUI manipulation procedure ... 96 6. 2. 4 Function specifications ... 96 6. 3 Serial I/O Function ... 99 6. 3. 1 Format setting ... 100 6. 3. 2 Serial log data file (*.log) ... 100 6. 3. 3 Serial transmission data file (*.ser) ... 102 6. 4 Panel Function ... 107 6. 4. 1 Connected parts types ... 108 10 User's Manual U17246EJ2V0UM 6. 4. 2 New creation and connection information settings ... 109 6. 4. 3 Simulation mode ... 109 6. 4. 4 Connection information list display ... 109 6. 4. 5 Operation after CPU reset ... 110 CHAPTER 7 WINDOW REFERENCE ... 111 7. 1 Window List ... 112 7. 2 Explanation of Windows ... 116 main window ... 117 Configuration dialog box ... 132 Extended Option dialog box ... 136 Debugger Option dialog box ... 139 Project File Save dialog box ... 145 Project File Load dialog box ... 147 Download dialog box ... 149 Upload dialog box ... 152 Load Module List dialog box ... 154 Source window ... 156 Source Search dialog box ... 161 Source Text move dialog box ... 163 Assemble window ... 165 Assemble Search dialog box ... 169 Address move dialog box ... 171 Symbol To Address dialog box ... 172 Watch window ... 174 Quick Watch dialog box ... 179 Add Watch dialog box ... 182 Change Watch dialog box ... 185 Local Variable window ... 187 Stack window ... 189 Memory window ... 192 Memory Search dialog box ... 195 Memory Fill dialog box ... 198 Memory Copy dialog box ... 200 Memory Compare dialog box ... 202 Memory Compare Result dialog box ... 204 DMM dialog box ... 206 Register window ... 208 Register Select dialog box ... 211 IOR/SFR window ... 213 IOR/SFR Select dialog box ... 218 Add I/O Port dialog box ... 221 Timer dialog box ... 223 Timer Result dialog box ... 226 Trace window ... 227 Trace Search dialog box ... 233 Trace Data Select dialog box ... 238 Trace move dialog box ... 241 Trace dialog box ... 243 Delay Count dialog box ... 246 Coverage window ... 247 Coverage Search dialog box ... 251 Coverage-Clear dialog box ... 253 Coverage-Address dialog box ... 254 Coverage-Condition Setting dialog box ... 255 Coverage-Efficiency View dialog box ... 257 Event Manager ... 259 Event dialog box ... 265 Event Link dialog box ... 272 Break dialog box ... 275 Snap Shot dialog box ... 277 Stub dialog box ... 282 View File Save dialog box ... 284 User's Manual U17246EJ2V0UM 11 View File Load dialog box ... 287 Environment Setting File Save dialog box ... 289 Environment Setting File Load dialog box ... 291 Reset Debugger dialog box ... 293 Exit Debugger dialog box ... 294 About dialog box ... 295 Console window ... 296 Font dialog box ... 297 Browse dialog box ... 299 Signal Data Editor window ... 301 Loop dialog box ... 308 Timing Chart window ... 310 Select Pin dialog box ... 316 Search Data dialog box ... 318 Standard I/O window ... 320 Standard I/O Buffer Size dialog box ... 323 Simulator Option dialog box ... 324 Serial window ... 326 Format (UART) dialog box ... 331 Format (CSI) dialog box ... 333 I/O Panel window ... 338 Parts Button Properties ... 346 Parts Key Properties ... 351 Parts Level Gauge Properties ... 354 Parts Led Properties ... 358 Parts Segment LED Properties ... 360 Parts Matrix Led Properties ... 365 Parts Buzzer Properties ... 368 Pull up/Pull down dialog box ... 371 Object Properties ... 373 Parts List dialog box ... 377 Entry Bitmap dialog box ... 379 Customize dialog box ... 380 Edit Colors dialog box ... 382 Font dialog box (Simulator Block) ... 383 Open dialog box ... 384 Save As dialog box ... 385 CHAPTER 8 COMMAND REFERENCE ... 386 8. 1 Command Line Rules ... 387 8. 2 Command List ... 387 8. 3 List of Variables ... 389 8. 4 List of Packages ... 389 8. 5 Key Bind ... 389 8. 6 Expansion window ... 389 8. 7 Callback Procedure ... 390 8. 8 Hook Procedure ... 391 8. 9 Related Files ... 392 8. 10 Cautions ... 392 8. 11 Explanation of Commands ... 392 address ... 393 assemble ... 394 batch ... 395 breakpoint ... 396 dbgexit ... 398 download ... 399 extwin ... 400 finish ... 401 go ... 402 help ... 403 hook ... 404 inspect ... 405 jump ... 406 12 User's Manual U17246EJ2V0UM map ... 407 mdi ... 408 memory ... 409 module ... 410 next ... 411 refresh ... 412 register ... 413 reset ... 414 run ... 415 step ... 416 stop ... 417 upload ... 418 version ... 419 watch ... 420 where ... 421 wish ... 422 xcoverage ... 423 xtime ... 424 xtrace ... 425 8. 12 Samples (Calculator Script) ... 426 APPENDIX A EXPANSION WINDOW ... 427 A. 1 Overview ... 427 A. 2 Sample List of Expansion Window ... 427 A. 3 Activation ... 427 A. 4 Explanation of each sample window ... 427 List window ... 428 Grep window ... 429 RRM window ... 430 Hook window ... 431 Memory Mapped I/O window ... 433 Memory Mapped I/O dialog box ... 434 APPENDIX B INPUT CONVENTIONS ... 435 B. 1 Usable Character Set ... 435 B. 2 Symbols ... 436 B. 3 Numeric Values ... 437 B. 4 Expressions and Operators ... 437 B. 5 File Names ... 440 APPENDIX C KEY FUNCTION LIST ... 441 APPENDIX D MESSAGES ... 444 D. 1 Display Format ... 444 D. 2 Types of Messages ... 445 D. 3 Message Lists ... 446 APPENDIX E INDEX ... 471 User's Manual U17246EJ2V0UM 13 LIST OF FIGURES Figure No 1-1 1-2 3-1 3-2 3-3 3-4 4-1 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 5-23 5-24 5-25 5-26 5-27 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 6-13 6-14 6-15 6-16 6-17 6-18 7-1 7-2 7-3 7-4 7-5 7-6 Title, Page SM+ for V850 ... 19 Example of System Configuration ... 21 Startup Option ... 26 Configuration Dialog Box ... 29 Main Window (Startup) ... 29 Exit Debugger Dialog Box ... 30 Downloading Multiple Files ... 33 Memory Space Managed by SM+ (With uPD70F326Y1) ... 38 Breakpoint Setting ... 45 Setting Break to Variable ... 46 Execution Button ... 47 [Run] Menu ... 47 Watch Window ... 49 Specification of the Display Format (Debugger Option dialog box) ... 49 Local Variable Window ... 50 Change Watch Dialog Box ... 51 Quick Watch Dialog Box ... 51 Stack Window ... 52 Displaying and Changing Memory Contents ... 53 Modifying Memory Contents (DMM Dialog Box) ... 54 Absolute Name/Function Name Switching ... 55 Displaying IOR/SFR Contents ... 56 Register I/O Port ... 56 Sets and Displays Timer Event (Timer Dialog Box) ... 57 Checking Trace Data ... 59 Coverage Result Display ... 63 Measuring Coverage Efficiency ... 63 Displaying Coverage Efficiency ... 64 Setting of Various Event Conditions ... 66 Managing Events (Event Manager) ... 69 Snap Shot Dialog box ... 70 Setting Stub Function Conditions ... 71 Flow of Stub Function ... 72 Automatic Save/Automatic Load Setting for Project File ... 74 Creation of Pin Input Data ... 86 Display of Pin Output Data ... 87 Pin Selection ... 87 Detailed Data Search ... 88 Signal Data File Outline ... 89 Description Example (Signal Data File) ... 91 Standard I/O Function ... 92 Standard I/O and File I/O Usage Procedure ... 93 Load Module Creation Procedure (CA850) ... 94 Load Module Creation Procedure (CC78K0 + RA78K0, or CC78K0S + RA78K0S) ... 95 Serial I/O Function ... 99 Serial Log Data File Outline ... 100 Saving Example (Serial Log Data File) ... 101 Serial Transmission Data File Outline: UART ... 102 Serial Transmission Data File Outline: CSI ... 102 Description Example (Serial Transmission Data File) ... 106 I/O Panel Window ... 107 Connected Parts Information List ... 109 Main Window ... 117 Tool Bar (Picture Only) ... 127 Tool Bar (Picture and Text) ... 127 Tool Bar (Simulator Block) ... 128 Status Bar ... 129 Configuration Dialog Box ... 132 14 User's Manual U17246EJ2V0UM 7-7 7-8 7-9 7-10 7-11 7-12 7-13 7-14 7-15 7-16 7-17 7-18 7-19 7-20 7-21 7-22 7-23 7-24 7-25 7-26 7-27 7-28 7-29 7-30 7-31 7-32 7-33 7-34 7-35 7-36 7-37 7-38 7-39 7-40 7-41 7-42 7-43 7-44 7-45 7-46 7-47 7-48 7-49 7-50 7-51 7-52 7-53 7-54 7-55 7-56 7-57 7-58 7-59 7-60 7-61 7-62 7-63 7-64 7-65 7-66 7-67 7-68 7-69 Extended Option Dialog Box ... 136 Debugger Option Dialog Box ... 139 Add Source Path Dialog Box ... 140 Project File Save Dialog Box ... 145 Project File Load Dialog Box ... 147 Download Dialog Box ... 149 The Progress of Download ... 149 Upload Dialog Box ... 152 Load Module List Dialog Box ... 154 Source Window ... 156 Source Search Dialog Box ... 161 Source Text Move Dialog Box ... 163 Assemble Window ... 165 Assemble Search Dialog Box ... 169 Address Move Dialog Box (Example: When Memory Window Is Open) ... 171 Symbol To Address Dialog Box ... 172 Watch Window ... 174 Quick Watch Dialog Box ... 179 Add Watch Dialog Box ... 182 Change Watch Dialog Box ... 185 Local Variable Window ... 187 Stack Window ... 189 Memory Window ... 192 Memory Search Dialog Box ... 195 Memory Fill Dialog Box ... 198 Memory Copy Dialog Box ... 200 Memory Compare Dialog Box ... 202 Memory Compare Result Dialog Box ... 204 DMM Dialog Box ... 206 Register Window ... 208 Register Select Dialog Box ... 211 IOR Window ... 213 SFR Window ... 214 IOR Select Dialog Box ... 218 SFR Select Dialog Box ... 218 Add I/O Port Dialog Box ... 221 Timer Dialog Box ... 223 Timer Result Dialog Box ... 226 Trace Window ... 227 Trace Search Dialog Box ... 233 Trace Data Select Dialog Box ... 238 Trace Move Dialog Box ... 241 Trace Dialog Box ... 243 Delay Count Dialog Box ... 246 Coverage Window ... 247 Coverage Search dialog box ... 251 Coverage-Clear dialog box ... 253 Coverage-Address dialog box ... 254 Coverage-Condition Setting dialog box ... 255 Coverage-Efficiency View dialog box ... 257 Event Manager (In detailed display mode) ... 259 Select Display Information Dialog Box ... 264 Event Dialog Box ... 265 Event Link Dialog Box ... 272 Break Dialog Box ... 275 Snap Shot Dialog Box (When "Register"selected) ... 277 Stub Dialog Box ... 282 View File Save Dialog Box ... 284 View File Load Dialog Box ... 287 Environment Setting File Save Dialog Box ... 289 Environment Setting File Load Dialog Box ... 291 Reset Debugger Dialog Box ... 293 Exit Debugger Dialog Box ... 294 User's Manual U17246EJ2V0UM 15 7-70 7-71 7-72 7-73 7-74 7-75 7-76 7-77 7-78 7-79 7-80 7-81 7-82 7-83 7-84 7-85 7-86 7-87 7-88 7-89 7-90 7-91 7-92 7-93 7-94 7-95 7-96 7-97 7-98 7-99 7-100 7-101 7-102 7-103 7-104 7-105 7-106 7-107 7-108 7-109 7-110 7-111 7-112 7-113 7-114 7-115 8-1 A-1 A-2 A-3 A-4 A-5 A-6 D-1 About Dialog Box ... 295 Console Window ... 296 Font Dialog Box ... 297 Browse Dialog Box ... 299 Signal Data Editor Window ... 301 Loop Dialog Box ... 308 Timing Chart Window ... 310 Maker A, B ... 314 Select Pin Dialog Box ... 316 Search Data Dialog Box ... 318 Standard I/O Window ... 320 Standard I/O Buffer Size Dialog Box ... 323 Simulator Option Dialog Box ([Standard Library Interface] tab) ... 324 Serial Window ... 326 Format (UART) Dialog Box ... 331 Format (CSI) Dialog Box ... 333 I/O Panel Window ... 338 Parts Button Properties ([Button Connection] tab) ... 346 Parts Button Properties ([Style] tab (Standard)) ... 346 Parts Display Example (Button) ... 350 Parts Key Properties ([Key Matrix Connection] tab) ... 351 Parts Display Example (Key Matrix) ... 353 Parts Level Gauge Properties ([Level Gauge Connection] tab) ... 354 Parts Level Gauge Properties ([Style] tab) ... 354 Parts Display Example (Level Gauge) ... 357 Parts Led Properties ([LED Connection] tab) ... 358 Parts Display Example (LED) ... 359 Parts Segment LED Properties [SegmentLED Connection] Tab ... 360 Parts Segment LED Properties [Style] Tab ... 360 Parts Display Example (7-segment LED) ... 364 Parts Matrix Led Properties ([Matrix LED Connection] Tab) ... 365 Parts Display Example (Matrix LED) ... 367 Parts Buzzer Properties [Buzzer Connection] Tab ... 368 Parts Display Example (Buzzer) ... 370 Pull up/Pull down dialog box ... 371 Object Properties ([Object Connection] Tab) ... 373 Object Properties ([Style] Tab) ... 373 Color Selection Palette ... 375 Parts List dialog box ... 377 Entry Bitmap Dialog Box ... 379 Customize Dialog Box ([Color] Tab) ... 380 Customize Dialog Box ([Font] Tab) ... 380 Edit Colors Dialog Box ... 382 Font Dialog Box ... 383 Open Dialog Box ... 384 Save As Dialog Box ... 385 Execution Screen ... 426 List Window ... 428 Grep Window ... 429 RRM Window ... 430 Hook Window ... 431 Memory Mapped I/O Window ... 433 Memory Mapped I/O Dialog Box ... 434 Error/Warning Messages ... 444 16 User's Manual U17246EJ2V0UM LIST OF TABLES Table No 2-1 3-1 3-2 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 5-23 5-24 5-25 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 7-1 7-2 7-3 7-4 7-5 7-6 7-7 7-8 7-9 7-10 7-11 7-12 7-13 7-14 7-15 7-16 7-17 7-18 7-19 7-20 7-21 7-22 Title, Page Install ... 24 Startup Options ... 27 Execution File ... 28 Debug Function List (Flow of Debugging Operations) ... 36 Type of File That Can Be Downloaded ... 39 Type of File That Can Be Uploaded ... 40 File Type Can Be Displayed ... 41 Specifying Symbols ... 43 Break Types ... 44 Type of Execution ... 47 Absolute Name to Function Name Correspondence [78K] ... 55 Trace Memory Size ... 58 Types of Trace Mode ... 60 Types of Tracer Control Mode ... 60 Types of Conditional Trace ... 61 Coverage Measurement Range ... 62 Various Event Conditions ... 65 Number of Enabled Events for Each Event Condition ... 68 Event Icon ... 69 Start Address of Function to Be Executed (Stub Function) ... 71 Sampling Range ... 73 Address Target Area and Effective Size ... 73 Contents Saved to Project File ... 75 Type of the View Files ... 77 Type of the Setting Files ... 78 Details of Jump Source Address ... 80 Details of Drag & Drop Function (Line/Address) ... 83 Details of Drag & Drop Function (Character String) ... 84 Simulation Function List ... 85 File Format Details (Signal Data File) ... 89 I/O Libraries for Simulator ... 95 Function Specifications (Standard I/O, File I/O Related) ... 97 File Format Details (Serial Log Data File) ... 100 File Format Details (Serial Transmission Data File) ... 103 Connected Parts ... 108 Operation of Connected Parts after CPU Reset ... 110 Window List ... 112 CPU Status ... 130 IE Status ... 130 Break Cause ... 130 Range and Unit of Internal ROM/RAM Setting ... 133 Type of Mapping Attribute ... 134 Event Setting Status (Event Mark) ... 157 Watch Window Display Format (Symbol) ... 175 Watch Window Display Format (Data) ... 176 Watch Window Input Format ... 183 How a Variable Is Handled When a Scope Is Specified ... 183 Measurable Values ... 225 Cause of Stopping Tracer ... 228 Number of Clocks and Time Tag Value [V850] ... 229 Settable Range of Address Condition (Trace) ... 235 Frame Number Specification Format ... 242 Number of Events Settable ... 244 Status List of Coverage Data ... 248 Separator for Displaying Event Details ... 260 Status Condition ... 266 Settable Range of Address Condition (Event) ... 268 Settable Range of Data Condition ... 270 User's Manual U17246EJ2V0UM 17 7-23 7-24 7-25 7-26 7-27 7-28 8-1 8-2 8-3 A-1 B-1 B-2 B-3 B-4 B-5 B-6 C-1 D-1 Pass Count ... 271 The Number of Event Conditions in Event Link Dialog Box ... 273 Number of Events Settable in Break Condition Setting Area ... 276 Address Settable Range (Snap Shot Dialog Box) ... 280 Snap Data Display Format ... 281 Data Clock Phase Settings ... 335 List of Debugger Control Commands ... 387 List of Console/Tcl Commands ... 388 Message ID ... 390 List of Expansion Window (Sample) ... 427 List of Character Set ... 435 List of Special Characters ... 435 Input Format of Numeric Values ... 437 List of Operators ... 438 Operator Priority ... 439 Range of Radixes ... 439 Key Function List ... 441 Types of Messages ... 445 18 User's Manual U17246EJ2V0UM CHAPTER 1 OVERVIEW CHAPTER 1 OVERVIEW The System Simulator SM+ (hereafter referred to as the SM+) is a software tool developed for NEC Electronics V850/78K0/78K0S Series of microcontrollers for embedded control. This software tool is intended to enable efficient debugging of user programs. SM+ allows debugging through simulation by downloading load module type object files to the target memory area of the simulator. The following types of SM+ are available according to the corresponding device (descriptions in parentheses show the symbols used to indicate each device in this manual). - SM+ for V850 (for V850 Series: [V850] ) - SM+ for 78K0 (for 78K0 Series: [78K0], [78K] ) - SM+ for 78K0S (for 78K0S Series: [78K0S], [78K] ) Figure 1-1 SM+ for V850 This chapter explains the following items regarding the SM+. - Features - System Configuration - Operating Environment - Cautions During Debugging User's Manual U17246EJ2V0UM 19 CHAPTER 1 OVERVIEW 1. 1 Features (1) Target-less evaluation Early logical debugging of user programs without an in-circuit emulator is made possible through simulation of target device operation including the operation of internal peripheral units and interrupt processing, in addition to the operation of the CPU itself. (2) Various simulation functions provided The operability is similar to that of the System Simulator ID Series developed for NEC Electronics. (3) Offer various simulation functions (a) Signal data display function Waveform display of the signal data of the specified pins is possible using the Timing Chart window. (b) Signal data input function Input during simulation of the created signal data with timing information is possible using the Signal Data Editor window. (c) Panel function Construction of a dummy target system is possible in the I/O Panel window. SM+ provides standard display of buttons, LEDs, key matrices, etc., as I/O devices, as well as manipulation items, and a target system can easily be constructed by allocating these elements. (d) Construction of user target system The user logic block in the target system can be constructed through user programming, by using the user open interfaceNote. Note Refer to "SM+ User Open I/F" (separate document). (4) Source debugging A C source program and source program in assembly language can be debugged. (5) Monitor function (automatic display updating function when execution is stopped) If execution of the user program is stopped, the values of the window displayed on the screen are automatically updated. (6) Saving/restoring debugging environment The debugging environment including information on setting of breakpoints and events, downloading files, and display status and position of windows can be saved to a file (project file). By loading this project file, the debugging environment can be restored. (7) Batch execution by command and creation of custom window A console window that allows batch processing on the command line and creation of the user's own custom window has been added. 20 User's Manual U17246EJ2V0UM CHAPTER 1 OVERVIEW (8) Function expansion by TIP or ToolLink [V850] / Function expansion by TIP [78K] Function expansion is possible by linking with NEC Electronics microcontroller tools that support TIP or ToolLink. 1. 2 System Configuration SM+ can also contribute to the realization of an even better development SM+ startup requires a device file. environment when linked to Project Manager that provides an integrated program development environment for the Windows platform (PM+, product of NEC Electronics). This section explains the following items related to the system configuration: - Example of system configuration - Internal configuration 1. 2. 1 Example of system configuration The example of system configuration is shown in the following figure. Figure 1-2 Example of System Configuration Host machine SM+ Device file PM+ 1. 2. 2 Internal configuration SM+ is configured of the following two blocks. - Debugger block Has debugging functions equivalent to those of the ID Series. (Refer to "CHAPTER 5 DEBUG FUNCTION".) - Simulator block Simulates the operation of the target device. (Refer to "CHAPTER 6 SIMULATION FUNCTION".) User's Manual U17246EJ2V0UM 21 CHAPTER 1 OVERVIEW 1. 3 Operating Environment This section explains the following items related to the operating environment: - Hardware environment - Software environment 1. 3. 1 Hardware environment (1) Host machine The machine by which the target OS operates (2) CPU Pentium IITM 300MHz or above (450MHz or above is recommended) (3) Memory RAM : 128Mbytes or above (256Mbytes or above is recommended) 1. 3. 2 Software environment (1) OS (any of the following) Windows98, Windows2000, Windows NT4.0 (Service Pack6 or above), WindowsMe, WindowsXP Home Edition, WindowsXP Professional Caution Regardless of which of the OSs above is used, we recommend that the latest Service Pack is installed. (2) Device file (Individual acquisition) The device file of the target device to be used. This file is available from the following Web site of NEC Electronics. http://www.necel.com/micro 22 User's Manual U17246EJ2V0UM CHAPTER 1 OVERVIEW 1. 4 Cautions During Debugging The cautions to be observed during debugging are described below. - When performing source level debugging 1. 4. 1 When performing source level debugging The object file for which source level debugging is performed must include symbol information or other information for debugging (debugging information). Therefore, perform the following processing during source file compiling. (1) When using PM+ Specify [Debug Build] when the Build mode is selected. (2) When using CA850 [V850] , LK78K0 [78K] on standalone basis Add the -g option. User's Manual U17246EJ2V0UM 23 CHAPTER 2 INSTALLATION CHAPTER 2 INSTALLATION This chapter explains the following items about installation of SM+: - Installing - Uninstalling 2. 1 Installing The following items must be installed, when the SM+ is used. Table 2-1 Install Item SM+ system disk Used device file Procedure Install the contents of this disk according to the automatically executed installer. Install this file according to the DFINST.exe dedicated startup installer by selecting [Start] menu -> [Program] -> [NEC Tools32] -> [Device File Installer]. Caution To install the SM+ again after the SM+ has been installed once, be sure to uninstall the SM+. If the SM+ is installed in a directory different from that, without uninstalling, the SM+ that has already been installed cannot be uninstalled. 2. 2 Uninstalling Perform uninstallation using [Add/Remove Programs] on the Control Panel. 24 User's Manual U17246EJ2V0UM CHAPTER 3 STARTING AND TERMINATING CHAPTER 3 STARTING AND TERMINATING This chapter explains the following items related to the starting and terminating the SM+: - Startup Option and Argument Specification - Starting - Terminating User's Manual U17246EJ2V0UM 25 CHAPTER 3 STARTING AND TERMINATING 3. 1 Startup Option and Argument Specification The procedure for specifying the startup options and arguments for the SM+ is described below. By specifying the startup options and arguments, it is possible to specify the script file at startup and the project file. Remark When starting up the SM+ from PM+, the startup option and argument settings are performed in [Debugger Settings...] in the [Tool] menu of PM+ (refer to "CHAPTER 4 ASSOCIATION WITH PM+"). The debugger startup option can be set to the option column. 3. 1. 1 1) Specification method Create an SM+ shortcut on the desktop. The SM+ execution file (*.exe) is located in the bin folder in the folder to which the installation was performed (refer to "Table 3-2 Execution File"). 2) Open the properties of the created shortcut and after the execution file name displayed in [Target:], specify the option and argument (refer to "3. 1. 2 Specification format and options"). Figure 3-1 Startup Option 26 User's Manual U17246EJ2V0UM CHAPTER 3 STARTING AND TERMINATING 3. 1. 2 Specification format and options (1) Specification format xxx.exe ?options? xxx.exe ?options? project Each option and argument is separated by a space. No distinction is made between uppercase and lowercase in the character string. Arguments enclosed between '?' can be omitted. When a project file is specified, that project file is read at startup. However, during PM+ startup, the project file specification is ignored. When there are spaces in the file names and paths, specify the project file names and script file names enclosed in double quotation marks (" "). (Refer to " Example 3) Specification when there are spaces in the path".) (2) Specification options The following options can be specified. Table 3-1 Startup Options Options /SC /SCRIPT:script file name Meaning Change background color of window to system color. Specify the script file to be executed at startup. (3) Specification example Example 1) Specification of script file only xxx.exe /script:c:/work/script.tcl Example 2) Specification of script file and project file xxx.exe /script:c:/work/script.tcl c:/work/project.prj Example 3) Specification when there are spaces in the path xxx.exe /script:"c:/work folder/script.tcl" "c:/work folder/project.prj" Caution Make the script file (*.tcl file) name excluding the extension different from the load module file name and project file name. In the case of this example, do not place a file named project.tcl in c:/work ( or c:/work folder). User's Manual U17246EJ2V0UM 27 CHAPTER 3 STARTING AND TERMINATING (4) Execution file Execution files and names displayed from the [Start] menu are as follows. Table 3-2 Execution File Device [V850] [78K0] [78K0S] Execution file sm850h32.exe smk0h32.exe smk0sh32.exe Name ([Start] Menu) SM+ for V850 SM+ for 78K0 SM+ for 78K0S 28 User's Manual U17246EJ2V0UM CHAPTER 3 STARTING AND TERMINATING 3. 2 1) Starting Start SM+ from the [Start] menu of PM+ or by clicking the shortcut created on the desktop. Refer to "4. 3 To Start SM+ from PM+" when starting from PM+. Start the SM+, the Configuration dialog box will be opened. Figure 3-2 Configuration Dialog Box 2) Set the items related to the operating environment of the SM+ in the Configuration dialog box. After setting each item, click the 3) The main window will be opened and the SM+ can be operated. Mainly use this window for debugging. Figure 3-3 Main Window (Startup) User's Manual U17246EJ2V0UM 29 CHAPTER 3 STARTING AND TERMINATING 3. 3 1) Terminating Select [File] menu-> [Exit] on the main window. The following the Exit Debugger dialog box will be opened: (An execution stop confirmation message is displayed when stop operation is performed during program execution.) Figure 3-4 Exit Debugger Dialog Box 2) To save the current debugging environment to a project file, click the 30 User's Manual U17246EJ2V0UM CHAPTER 4 ASSOCIATION WITH PM+ CHAPTER 4 ASSOCIATION WITH PM+ The SM+ can automatically perform a series of operations in development processes, such as creating source files -> compiling -> debugging -> correcting source files, in association with the PM+. This chapter explains the following items related to association with the PM+. For details of the PM+ functions, refer to the PM+ User's Manual. - Setting Build Mode - Registering Debugger to PM+ Project - To Start SM+ from PM+ - Auto Load Caution If a load module file is created by using the Windows command prompt, the function to associate the SM+ with the PM+ cannot be used. User's Manual U17246EJ2V0UM 31 CHAPTER 4 ASSOCIATION WITH PM+ 4. 1 Setting Build Mode To debug the load module file created by the PM+ on the SM+ at the source level, build to output symbol information for debugging must be performed to create a load module file. This setting can be performed by selecting [Debug Build] on the PM+. 32 User's Manual U17246EJ2V0UM CHAPTER 4 ASSOCIATION WITH PM+ 4. 2 Registering Debugger to PM+ Project The debugger to be used or the load module files to be downloaded can be specified for each project in the PM+. 4. 2. 1 Selecting debugger The procedure for selecting the debugger is as follows: The SM+ is registered as the debugger of the active project. The SM+ icon is displayed on the tool bar of the PM+. (1) Creating a new workspace 1) Select [File] menu -> [New Workspace...] on the PM+. -> This opens the dialog box to create a new workspace using the wizard format. 2) Creating the necessary settings for the workspace with the wizard, the [Select Debugger] dialog box will be opened. Specify SM+ in this dialog box. (Refer to "Table 3-2 Execution File".) refer to the "PM+ online help" or "User's manual". (2) Using an existing workspace 1) Select [Tool] menu -> [Debugger Settings...] on the PM+. -> The [Debugger Settings] dialog box will be opened. 2) Specify SM+ and click the Load module files in the same project group can be downloaded to SM+ when using SM+ for V850. Download multiple load module files by specifying items in the [Debugger Settings] dialog box of PM+. Figure 4-1 Downloading Multiple Files For details of the project group, refer to the "PM+ online help" or "User's manual". Remark Multiple load module files that are being downloaded can be checked in the Load Module List dialog box of the SM+. User's Manual U17246EJ2V0UM 33 CHAPTER 4 ASSOCIATION WITH PM+ 4. 3 To Start SM+ from PM+ The SM+ can be started from the PM+ as follows: - Click the SM+ starting button on the tool bar of the PM+. - Select the [Build] menu -> [Debug] on the PM+. - Select the [Build] menu -> [Build and Debug] on the PM+. - Select the [Build] menu -> [Rebuild and Debug] on the PM+. If the debugging environment of the SM+ is saved to a project file currently being used by the PM+, it will be started in the debugging environment saved in the project file. If the debugging environment of the SM+ is not saved to a project file being used by the PM+, the Configuration dialog box is opened. At this time, the device type (chip name) cannot be changed. 4. 3. 1 Restoring debugging environment The previous debugging environment can be restored by the following procedure when the SM+ is started from the PM+: 1) 2) Create a new workspace (project file: e.g., sample.prj) on the PM+Note. Start the SM+ from the PM+. Because a new project file is created, set items other than the device type (chip name) in the Configuration dialog box in the same manner as when only the SM+ is started. 3) 4) 5) Download the load module file to be debugged with the Download dialog box of the SM+. Debug the load module file on the SM+. Click the 34 User's Manual U17246EJ2V0UM CHAPTER 4 ASSOCIATION WITH PM+ 4. 4 Auto Load If a bug is found while the load module file is being debugged by the SM+, correct the source file using the following procedure. Compiling and re-downloading the file can be automatically executed. (Refer to "4. 4. 1 Auto load by correcting source code".) The load module is downloaded again to the SM+ by compiling and linking the file on the PM+ with the activated SM+. (Refer to "4. 4. 2 Auto load by starting debugger".) Caution This processing cannot be performed if it is selected that the standard editor (idea-L) is used with the PM+. 4. 4. 1 Auto load by correcting source code Correct the source file for auto load as follows: 1) Open the source file to be corrected in the Source window. Select [File] menu -> [Open] and specify the file to be corrected on the SM+ (if the file is already open in the Source window, that window is displayed in the forefront). -> The specified file will be opened in the Source window. 2) Select [Edit] menu -> [Edit Source] on the SM+. -> An editor will be opened and the specified source file will be read. 3) 4) Correct the source file on the editor. Terminate the editor. The CPU reset is not performed when the load module file is automatically downloaded. The debug window that was opened when the editor was called, and each event setting will be restored. If the previously used line or symbol has been deleted as a result of correcting the source file, the following happens: - A variable that was displayed is dimmed. - The event mark of an event condition is displayed in yellow. 5) 4. 4. 2 Select [Build] menu -> [Build and Debug], or [Build] menu -> [Rebuild and Debug] on the PM+. Auto load by starting debugger Caution If the following operation is performed on the PM+ with the SM+ started, the load module will be automatically downloaded to the SM+. - Selecting the [Build] menu -> [Build and Debug] on the PM+. - Selecting the [Build] menu -> [Rebuild and Debug] on the PM+. Remark Specify whether to use a CPU reset after downloading from [Debugger Settings...] on the [Tool] menu of PM+ (a CPU reset is performed by default). User's Manual U17246EJ2V0UM 35 CHAPTER 5 DEBUG FUNCTION CHAPTER 5 DEBUG FUNCTION This chapter explains about debug function of SM+. Table 5-1 Debug Function List (Flow of Debugging Operations) Item To set the debugging environment To download the load module To display the source file and the disassemble result To set a break point To execute the user program To check the variable value To check and edit the memory contents To check and change the register variable To check the execution time To check the trace data To check the coverage data To manage the events Snapshot function Stub function RRM function To save the debug environment and window status Jump function, linking window function Refer To 5. 1 Setting Debugging Environment 5. 2 Download Function, Upload Function 5. 3 Source Display, Disassemble Display Function 5. 4 Break Function 5. 5 Program Execution Function 5. 6 Watch Function 5. 7 Memory Manipulation Function 5. 8 Register Manipulation Function 5. 9 Timer Function 5. 10 Trace Function 5. 11 Coverage Measurement Function 5. 12 Event Function 5. 13 Snapshot Function 5. 14 Stub Function 5. 15 RAM Sampling Function 5. 16 Load/Save Function 5. 17 Functions Common to Each Window 36 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 1 Setting Debugging Environment This section explains the following items related to the setting debugging environment: - Setting operating environment - Setting option - Setting mapping 5. 1. 1 Setting operating environment The simulator operating environment settings are performed in the Configuration dialog box that is automatically displayed when SM+ starts up. If a project file already exists, the debugging environment can be restored by clicking the The extended options and debug options are set in the Extended Option dialog box, the Debugger Option dialog box . 5. 1. 3 Setting mapping The SM+ virtually manages a contiguous memory space the same as that of the target device specified in the Configuration dialog box, by securing an alternate memory on the host machine. Consequently, the size of the internal ROM/RAM area can be changed or any memory area can be mapped as an emulation ROM/RAM area. The following figure shows the target memory space if the uPD70F3261Y is specified in the Configuration dialog box as the CPU to be used. User's Manual U17246EJ2V0UM 37 CHAPTER 5 DEBUG FUNCTION Figure 5-1 Memory Space Managed by SM+ (With uPD70F326Y1) 0x03FFFFFF 0x03FFF000 0x03FFEFFF 0x03FF7000 0x00FFFFFF Memory space 64M bytes 38 Peripheral I/O register (4K bytes) Internal RAM (32K byte) Scalable for every target device Target memory Program memory Data memory 0x00100000 0x0005FFFF 0x00000000 External RAM (15M bytes) Configulable area - Guard area - Emulation ROM - Emulation RAM Internal ROM (320K bytes) Scalable for every target device User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 2 Download Function, Upload Function SM+ allows downloading and uploading of object files in the formats listed in the following table: Table 5-2, Table 5-3. This section explains the following items: - Download - Upload 5. 2. 1 Download Object files are downloaded in the Download dialog box. The corresponding source text file (Source window) is displayed by downloading load module files with debug information. Remark Multiple load module files can be downloaded. Loaded files can be checked in the Load Module List dialog box that is opened by selecting [File] menu -> [Load Module] . [V850] Table 5-2 Type of File That Can Be Downloaded Format Load module (ELF(.OUT)) [V850] Load module (XCOFF(.LNK, .LMF)) [78K] Intel Hex format (00, 01, 02, 03 - 20 bit-address) Motorola Hex format S type (S0, S3, S7, S8) [V850] (S0, S2, S8) [78K] Extended Tektronix Hex format Binary data Coverage results Binary Data (*.bin) Coverage (*.cvb) Extension Load Module (*.out) Load Module (*.lnk, *.lmf) Hex Format (*.hex)Note Note Automatic format detection User's Manual U17246EJ2V0UM 39 CHAPTER 5 DEBUG FUNCTION 5. 2. 2 Upload Uploading of memory contents, etc., is performed in the Upload dialog box. The saving range can be set. Table 5-3 Type of File That Can Be Uploaded Format Intel Hex format (00, 01, 02, 03 - 20bit-address) [V850] (standard - 16bit-address) [78K] Motorola Hex format S type (S0, S3, S7 - 32bit-address) [V850] (S0, S2, S8 - 24bit-address) [78K] Extended Tektronix Hex format Binary data Coverage results Binary Data (*.bin) Coverage (*.cvb) Extension Hex Format (*.hex)Note Note Specify saving format. 40 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 3 Source Display, Disassemble Display Function Disassemble display and online assembly are per- Source file display is performed in the Source window. formed in the Assemble window. This section explains the following items: - Source display - Disassemble display - Mixed display mode (Source window) - Convert symbol (Symbol to Address) 5. 3. 1 Source display The corresponding text file is displayed in the Source window by downloading a load module file having debug information. The display start position can be changed in the Source Text move dialog box displayed by selecting [View] menu -> [Move...]. Specifications related to the tab size, display font, etc., and specification of the source path are made in the Debugger Option dialog box. Specify a searching method in the Source Search dialog box opened by clicking the 5. 3. 2 Disassemble display Disassemble display is performed in the Assemble window. The display start position can be changed in the Address move dialog box opened by selecting [View] menu -> [Move...]. Offset display and register name display are specified in the Debugger Option dialog box. Specify a searching method in the Assemble Search dialog box opened by clicking the User's Manual U17246EJ2V0UM 41 CHAPTER 5 DEBUG FUNCTION 5. 3. 3 Mixed display mode (Source window) Programs can be disassembled and displayed combined with the source file by selecting [View] menu -> [Mix] in the Source window. The contents displayed in the mixed display mode can be saved as a view file. Normal display mode In the normal display mode, general text files can be displayed as well as source files. Mixed display mode If a program code corresponds to the line of the displayed source file, the disassembly line is displayed next to the source line. The label of the address, code data, and disassembled mnemonic are displayed (the display start position of the mnemonic is adjusted by the set value of the tab size). Caution The mixed display mode is valid only when the load module is downloaded and the symbol information is read, and the corresponding source file is displayed. 42 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 3. 4 Convert symbol (Symbol to Address) In the Symbol To Address dialog box, can be displayed the address of the specified variable or function, or the value of the specified symbol. Convert symbol is performed by selecting the character string to be converted in the Source window or Assemble window, and then selecting context menu -> [Symbol...]. The Specification symbols is indicated below. Table 5-5 Specifying Symbols Conversion Target Variable Specification Method var file#var (to specify a static variable with file name) func#var (to specify a static variable with function name) file#func#var (to specify a static variable with file name and function name) func file#func (to specify a static function with file name) label file#label (to specify a local label with file name) equsym file#equsym (to specify a local EQU symbol with file name) bitsym file#bitsym (to specify a local bit symbol with file name) file#no prog$file#no portname I/O regname sfrname regname pswname Function Label EQU symbol [78K] Bit symbol [78K] Line number of source file I/O port name I/O register name [V850] SFR name [78K] Register name PSW flag name Remark 1 Separator '#' '#' is used as a separator for file names, variables, function names, and line numbers. If a specified symbol is not found in the scope, all symbols (static variables, static functions, local labels) are searched. Remark 2 Separator '$' To specify a load module name when two or more load modules are read, use "$" as a separator to delimit the load module name from a file name, variable, function name, or symbol name. [V850] In the default status, a symbol name takes precedence. To temporarily change the priority, prefixing "$" to a symbol gives the priority to a register name. User's Manual U17246EJ2V0UM 43 CHAPTER 5 DEBUG FUNCTION 5. 4 Break Function The break function is used to stop execution of the user program by the CPU and operation of the tracer. This section explains the following items: - Break Types - Breakpoint setting - Setting breaks to variables 5. 4. 1 Break Types The SM+ has the following break functions. Table 5-6 Break Types Item Hardware break Note1 (Event detection break) [Come Here] break Note2 (Simple break) Contents Function to stop user program execution upon detection of the set break event condition. -> Refer to "5. 4. 2 Breakpoint setting". Function to stop user program execution selected by selecting [Run] menu -> [Come Here] upon detection of address specified in the Source window the Assemble window. Function to stop execution upon satisfaction of the stop condition of each command ([Step In], [Next Over], [Return Out], [Slow Motion]). Function to forcibly stop execution by selecting [Run] menu > [Stop], or selecting the STOP button. It is valid for all the execution commands. Break on satisfaction of condition of step execution Forced break Note1 Note2 This break is valid for [Go], [Go & GO], [Come Here], and [Restart]. After user program execution has been stopped, the breakpoint by this function is eliminated. During execution of a user program by this function, break events set before the cursor position does not occur. 44 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 4. 2 Breakpoint setting Breakpoints can simply be set to the desired location by clicking in the Source window or the Assemble window. Since breakpoints are set as break event conditions and managed using the Event Function, restrictions apply to the number of breakpoints that can be set. tion".) (1) Breakpoint setting method Breakpoints are executed by clicking lines in which '*' is displayed (lines where program code exists). If a breakpoint is set on a line on which an event breakpoint has already been set, "A" indicating that multiple events have been set is marked (refer to "Table 7-7 Event Setting Status (Event Mark)"). Remark Setting of before-execution/after-execution breaks is possible in the Extended Option dialog box. Figure 5-2 Breakpoint Setting (Refer to "5. 12. 4 Number of enabled events for each event condi- (2) Deleting a breakpoint method Click the position at which the breakpoint to be deleted is set. As a result of deletion, If another event remains, however, the mark of that event is displayed. User's Manual U17246EJ2V0UM 45 CHAPTER 5 DEBUG FUNCTION 5. 4. 3 Setting breaks to variables Access breaks can easily be set to variables from the context menu in the Source window or the Watch window. Figure 5-3 Setting Break to Variable 46 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 5 Program Execution Function The program execution function is used to start execution of the user program by the CPU and operation of the tracer. Through user program execution, the program counter (PC) advances until the set breakpoint or forced break. (Refer to "5. 4 Break Function".) While the user program is being executed, trace event condition and timer event condition can be set. (Refer to " Trace dialog box"," Timer dialog box".) The following types of SM+ execution functions are provided. They are operated using the execution buttons on the tool bar , or from the [Run] menu. Figure 5-4 Execution Button Figure 5-5 [Run] Menu Table 5-7 Type of Execution Items [Restart] Contents The CPU is reset and the user program is executed starting from address 0. [V850] The CPU is reset and the user program is executed starting from RESET address. [78K] This is the same operation as "resetting the CPU before execution of the user program and executing [Go]". The user program is executed starting from the address indicated by the current PC register and is stopped if a set break event condition is satisfied. The user program is executed starting from the address indicated by the current PC register Execution of the user program continues, ignoring set breakpoints. The user program is executed until execution returns to the calling function described in C language. [Go] [Ignore break points and Go] [Return Out] User's Manual U17246EJ2V0UM 47 CHAPTER 5 DEBUG FUNCTION Items [Step In] Contents In the Source window,Step execution of one line of the source text is performed starting from the current PC register value and the contents of each window are updated. In the Assemble window,One instruction is executed from the current PC register value and the contents of each window are updated. jarl instruction [V850] Next step execution is performed, assuming the function or subroutine called by the jarl instruction as one step (step execution continues until the nesting level becomes the same as when the jarl instruction was executed). Instruction other than jarl [V850] The same processing as [Step In] is performed. CALL / CALLT / CALLF instruction [78K] Next step execution is performed, assuming the function or subroutine called by the CALL / CALLT / CALLF instruction as one step (step execution continues until the nesting level becomes the same as when the CALL / CALLT / CALLF instruction was executed). Instruction other than CALL / CALLT / CALLF [78K] The same processing as [Step In] is performed. This command executes the user program starting from the specified address. Execution of the user program is stopped when a set break event condition is satisfied. The user program is executed from the address indicated by the current PC register to the address selected in the line/address display area of the Source window or the Assemble window, and then a break occurs. While the user program is being executed, the break event currently set does not occur. The user program is executed starting from the address indicated by the current PC register and stopped if a set break event condition is satisfied. The contents of each window are updated, and execution of the user program is resumed from the address at which the program was stopped. This operation is repeated until the user executes [Stop]. Step execution of one line is performed from the address indicated by the current PC register value in the source mode. In the instruction mode, step execution of one instruction is performed. The contents of each window are updated each time step execution is performed. This operation is repeated until the user executes [Stop]. [Next Over] [Start From Here] [Come Here] [Go & Go] [Slowmotion] 48 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 6 Watch Function This section explains the following items related to the watch function: - Displaying and changing data values - Displaying and changing local variable values - Registering and deleting watch data - Changing watch data - Temporarily displaying and changing data values - Callout watch function - Stack trace display function 5. 6. 1 Displaying and changing data values Shifts in data values can be checked by Data values are displayed and changed in the Watch window. registering watch data. The display format is specified in the Debugger Option dialog box. Figure 5-6 Watch Window Figure 5-7 Specification of the Display Format (Debugger Option dialog box) User's Manual U17246EJ2V0UM 49 CHAPTER 5 DEBUG FUNCTION 5. 6. 2 Displaying and changing local variable values Local variables are displayed and changed in the Local Variable window. Local variables within the current function are automatically displayed in this window. (Variable addition/deletion is not possible.) Figure 5-8 Local Variable Window 5. 6. 3 Registering and deleting watch data Data can be registered to the Watch window from the Source window or the Assemble window. This is simply done by selecting the variable or symbol name in the respective window, and then clicking the elements of an array, and members of structures and unions, cannot be deleted. 50 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 6. 4 Changing watch data Watch data is changed in the Change Watch dialog box. Note that the symbol name can be changed even if it results in duplication of a name already in use with existing data. Figure 5-9 Change Watch Dialog Box 5. 6. 5 Temporarily displaying and changing data values Data values are temporarily displayed and changed in the Quick Watch dialog box. Select the desired variable or symbol name in the Source window or the Assemble window and click the User's Manual U17246EJ2V0UM 51 CHAPTER 5 DEBUG FUNCTION 5. 6. 6 Callout watch function The corresponding variable value pops up when the mouse cursor is placed over a selected variable in the Source window or the Assemble window. 5. 6. 7 Stack trace display function This function displays the stack contents of the current user program in the Stack window. Figure 5-11 Stack Window 52 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 7 Memory Manipulation Function This section explains the following items related to the memory manipulation: Verify check, etc., is specified in the Extended Option dialog box. - Displaying and changing memory contents - Filling, copying, and comparing memory contents - Modifying memory contents (DMM function) 5. 7. 1 Displaying and changing memory contents In the Memory window, the memory contents can be displayed or changed by using mnemonic codes, hexadecimal codes, and ASCII codes. Searching is done in the Memory Search dialog box displayed by clicking the 5. 7. 2 Filling, copying, and comparing memory contents Memory contents are Filled, copied, and compared in the Memory Fill dialog box, the Memory Copy dialog box, and the Memory Compare dialog box displayed by selecting [Edit] menu -> [Memory] -> [Fill.../Copy.../Compare...]. The comparison results are displayed in the Memory Compare Result dialog box. Caution The address width changes when memory banks are used. [78K0] User's Manual U17246EJ2V0UM 53 CHAPTER 5 DEBUG FUNCTION 5. 7. 3 Modifying memory contents (DMM function) Memory contents can be modified during user program execution in the DMM dialog box displayed by clicking the 54 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 8 Register Manipulation Function This section explains the following items related to the register manipulation function. - Displaying and changing register contents - Displaying and changing IOR/SFR contents - Displaying and changing I/O port contents 5. 8. 1 Displaying and changing register contents Register contents can be displayed and changed in the Register window. Register name display switching (absolute name/function name) can be done in the Debugger Option dialog box. Remark The display register is selected in the Register Select dialog box. [V850] Figure 5-14 Absolute Name/Function Name Switching Table 5-8 Absolute Name to Function Name Correspondence [78K] Function Name Pair Register ax Register x a bc c b de e d hl l h rp3 rp2 rp1 Absolute Name Pair Register rp0 Register r0 r1 r2 r3 r4 r5 r6 r7 User's Manual U17246EJ2V0UM 55 CHAPTER 5 DEBUG FUNCTION 5. 8. 2 Displaying and changing IOR/SFR contents The IOR/SFR contents can be displayed and changed in the IOR/SFR window. The display start position can be changed in the Address move dialog box displayed by selecting [View] menu -> [Move...]. The display register is selected in the IOR/SFR Select dialog box. Figure 5-15 Displaying IOR/SFR Contents 5. 8. 3 Displaying and changing I/O port contents User-defined I/O ports can be displayed and changed in the IOR/SFR window once they have been registered in the Add I/O Port dialog box. In the case of products that support programmable I/O registers, programmable I/O register contents can be displayed and changed by setting programmable I/O area use in the Configuration dialog box. Figure 5-16 Register I/O Port 56 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 9 Timer Function The timer function measures the execution time (Run-Break time) from the start of user program execution until a break, or the execution time in a specific user program interval using timer events. Caution The timer function is enabled by selecting [Option] menu -> [Timer ON]. This section explains the following items: - Timer event conditions - Run-Break event 5. 9. 1 Timer event conditions A timer event condition specifies the trigger by which time measurement is started or stopped. Timer event conditions are set in the Timer dialog box. (Refer to "5. 12 Event Function".) Figure 5-17 Sets and Displays Timer Event (Timer Dialog Box) Continuous display in the Timer Result dialog box can be opened by clicking the Run-Break event is a timer event name given to a timer event condition that measures the execution time from execution to break. Run-break events are registered in advance and the run-break time can be displayed through specification in the Timer dialog box. Since Run-Break events are not included in the number of timer events that can be simultaneously enabled (refer to "5. 12. 4 Number of enabled events for each event condition"), they can be used added to the number of valid timer event conditions. User's Manual U17246EJ2V0UM 57 CHAPTER 5 DEBUG FUNCTION 5. 10 Trace Function The trace function is used to save the history of the data indicating the execution process of the user program to the trace memory. Caution The trace function is enabled by selecting [Option] menu -> [Tracer ON]. This section explains the following items: - Trace memory - Checking trace data - Mixed display mode (Trace window) - Tracer Operation - Setting conditional trace 5. 10. 1 Trace memory SM+ has trace memory with a ring structure. Size specification is done in the Extended Option dialog box. The maximum trace memory capacity is as follows. Table 5-9 Trace Memory Size Product name SM+ 16M frames Maximum value 58 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 10. 2 Checking trace data The trace data saved to the trace memory can be checked in the Trace window. Trace data can be searched in the Trace Search dialog box opened by clicking the 5. 10. 3 Mixed display mode (Trace window) Source files can be displayed combined with trace results by selecting [View] menu -> [Mix] in the Trace window (mixed display mode). If a program code corresponds on the program fetch address to be displayed, a source file line is displayed before the line indicating the results of tracing that program fetch address. The source file line is displayed, emphasized in green. Caution The mixed display mode is valid only when the load module has been downloaded and symbol information is read, and when a fetch address, fetch data, fetch status, or result of disassembly is displayed. User's Manual U17246EJ2V0UM 59 CHAPTER 5 DEBUG FUNCTION 5. 10. 4 Tracer Operation The trace operation differs as follows according to the user program execution format and the tracer control mode. Tracer manipulations during program execution are performed by selecting [Run] menu -> [Tracer Start/ Tracer Stop]. (1) Operation during execution The tracer operation differs as follows according to [Run] menu -> [Uncond. Trace ON/Cond. Trace ON] selection. Table 5-10 Types of Trace Mode Item Unconditional trace Conditional trace Contents Trace is started when execution of user program, and ends when a break occurs. At this time, the set trace event conditions are ignored. Trace is started or stopped by the condition set in the Trace dialog box (refer to "5. 10. 5 Setting conditional trace"). If a break occurs while a trace is being executed, however, trace is stopped immediately. (2) Operation during Step In execution The tracer operates every step execution, and trace data of one step is successively added to the trace memory. (3) Operation during Next Over execution The operation of the tracer differs depending on the instruction to which Next Over is to be executed. (a) jarl disp22, [lp] instruction [V850] The jarl instruction and the subroutine that was called are traced. (b) CALL / CALLT / CALLF instruction [78K] The CALL / CALLT / CALLF instruction and the subroutine that was called are traced. (c) Other instructions The same operation as that during Step In execution is performed. (4) Tracer control mode There are the following types of trace control mode. These trace mode settings are performed from the [Run] menu. Table 5-11 Types of Tracer Control Mode Mode Non Stop Full Stop Full Break Contents Goes around the trace memory and overwrites data from the oldest frame (default). Goes around the trace memory and then stops the tracer. Goes around the trace memory and then stops the tracer and program execution 60 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION Mode Delay Trigger Stop Delay Trigger Break Contents Traces data by the number of delay count frames and stops the tracer when a delay trigger event has occurred. Traces data by the number of delay count frames and stops the tracer and program execution when a delay trigger event has occurred. 5. 10. 5 Setting conditional trace A trace event condition triggers starting/stopping trace execution when a conditional trace is set. By setting a trace event condition in the Trace dialog box, the conditional trace can be set (refer to "5. 12 Event Function"). There are the following types of conditional trace. Table 5-12 Types of Conditional Trace Item Section trace Contents, Setting method Executes a trace between two specified conditions (in a specific zone). A section trace can be executed by setting a trace start event and trace end event in the Trace dialog box and selecting [Run] menu -> [Cond. Trace ON]. Executes a trace only when a condition is satisfied. If two or more events are set as qualify trace events, a qualify trace can be executed by executing a conditional trace. A qualify trace can be executed by setting a qualify trace event in the Trace dialog box and selecting [Run] menu -> [Cond. Trace ON]. Executes a trace by the number of delay counts after a condition has been satisfied. A delay trigger trace can be executed by setting a delay trigger event in the Trace dialog box, setting a delay count in the Delay Count dialog box and selecting [Run] menu -> [Cond. Trace ON]. In this case, select [Delay Trigger Stop] , [Delay Trigger Break] . Qualify trace Delay trigger trace User's Manual U17246EJ2V0UM 61 CHAPTER 5 DEBUG FUNCTION 5. 11 Coverage Measurement Function The coverage measurement function records the status (execution, read, write, etc.) for each address during user program execution. Remark The coverage measurement function is enabled by selecting [Option] menu -> [Coverage ON]. This section explains the following items: - Coverage measurement - Selecting coverage range [V850] - Coverage result display - Measuring and displaying coverage efficiency 5. 11. 1 Coverage measurement The coverage measurement results are recorded to the coverage memory by executing a program. Coverage measurement is manipulated during program execution by selecting [Run] menu -> [Coverage Start/ Stop]. 5. 11. 2 Selecting coverage range [V850] The coverage range is selected in the Coverage-Address dialog box. The selectable coverage ranges are as follows. Table 5-13 Coverage Measurement Range Device [V850] Measurement Range Any 1 MB range from addresses 0x100000 to 0x3FFFFFF (Default: Addresses 0x100000 to 0x1FFFFF) Plus addresses 0x000000 to 0x0FFFFF 62 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 11. 3 Coverage result display The coverage results can be checked in the Coverage window. The data can be searched in the Coverage Search dialog box opened by clicking the 5. 11. 4 Measuring and displaying coverage efficiency The coverage efficiency is measured in the Coverage-Condition Setting dialog box. Settings can be made by address range and in function units. The coverage efficiency measurement results can be checked in the Coverage-Efficiency View dialog box opened by clicking the User's Manual U17246EJ2V0UM 63 CHAPTER 5 DEBUG FUNCTION Figure 5-21 Displaying Coverage Efficiency 64 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 12 Event Function Events specify specific states of the target system during debugging ,such as "fetched address 0x1000" or "wrote data to address 0x2000". In SM+, such events are used as action triggers for each debugging function, such as break and trace. This section explains the following items: - Using event function - Creating events - Setting various event conditions - Number of enabled events for each event condition - Managing events 5. 12. 1 Using event function Events (event conditions and event link conditions) are assigned various debugging functions and consist of the event conditions listed in the following table. As a result, event conditions can be utilized according to the debugging purpose. Table 5-14 Various Event Conditions Contents ->Setting Dialog Box Condition in which the execution of the user program or operation of a tracer is stopped. (refer to "5. 4 Break Function"). -> Break dialog box Condition in which the process of user program execution is saved to the trace memory (refer to "5. 10 Trace Function"). -> Trace dialog box Condition for specifying the time measurement start timing and stop timing (refer to "5. 9 Timer Function"). -> Timer dialog box Condition for specifying the program insertion timing (refer to "5. 14 Stub Function"). -> Stub dialog box Condition for specifying the snapshot timing (refer to "5. 13 Snapshot Function"). -> Snap Shot dialog box Event Condition Break event Mark B Trace event T Timer event Ti Stub event U Snapshot event S User's Manual U17246EJ2V0UM 65 CHAPTER 5 DEBUG FUNCTION 5. 12. 2 Creating events Events can be used as action triggers of various event conditions described before through registration of event conditions and event link conditions, by individually naming states called events. (1) Creating and registering events Event conditions are usually created in the Event dialog box. Set an address condition, status condition, and data condition in this dialog box. Specify a combination of these as one event condition and name and register this event condition. A simple method consists in using event conditions generated by setting breakpoint in the, Source window and the Assemble window. (Refer to "5. 4. 2 Breakpoint setting".) (2) Creating and registering event links Event link conditions are conditions for single events that provide ordered restrictions for event conditions, and are generated when user programs are executed according to the specified sequence. To create an event link condition, use the Event Link dialog box. 5. 12. 3 Setting various event conditions Various event conditions listed in Table 5-14 are individually created in the corresponding dialog box. (1) Setting of various event conditions The setting of the various event conditions is done by selecting the event icon of the desired event condition or event link condition displayed in the event manager area (or Event Manager) in the respective setting dialog box, and dragging and dropping this icon in the condition area to be set. Figure 5-22 Setting of Various Event Conditions The shape of the mouse cursor changes to "OK" when it is dragged over a settable condition area. Regarding the created event conditions, the event icon mark becomes red and the setting is enabled by clicking the 66 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION (2) Setting using selection mode (settings after checking contents) The Event dialog box and the Event Link dialog box are open in the "selection mode" by placing the focus on the condition area to be set and then clicking the User's Manual U17246EJ2V0UM 67 CHAPTER 5 DEBUG FUNCTION 5. 12. 4 Number of enabled events for each event condition Up to 256 conditions can be registered as event conditions or various event conditions. One event condition or link event condition can be set for multiple types of events such as break, trace, and timer. However, the number of event conditions that can be simultaneously set (enabled) is limited as follows. Therefore, if the valid number is exceeded or if the used event conditions or event link conditions exceed the maximum number that can be used simultaneously, it is necessary to disable the set various event conditions once and then register them again. (Refer to "5. 12. 5 Managing events".) Table 5-15 Number of Enabled Events for Each Event Condition Event Product Execution Access Event link Break Trace Snap shot Stub Timer SM+ 64 16a. 64 64 8 1 8 a. Includes event link conditions used for enabled break, trace, snapshot, and stub functions. 68 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 12. 5 Managing events Events are managed by the Event Manager. The Event Manager allows display, enabling/disabling, and deletion of the Various Event Conditions. Figure 5-23 Managing Events (Event Manager) (1) Event icons Event icons consist of a mark and an event name indicating the type of event. The color of each event icon indicates the setting status of that event. Enable/disable is switched by clicking the mark part. Table 5-16 Event Icon Character Color Red Mark E.L. B.T.Ti.U.S. Meaning Indicates that the event condition or event link condition which is used for various event conditions is valid. Indicates that the Various Event Conditions is valid. The various events occur when its condition is satisfied. Indicates that the event condition or event link condition which is used for various event conditions is invalid. Indicates that the Various Event Conditions is invalid. The various events do not occur even when its condition is satisfied. Indicates that the symbol specified for an event is held pending because it cannot be recognized by the program currently loaded. Indicates that the Various Event Conditions is held pending. The various events do not occur even when its condition is satisfied. Black E.L. B.T.Ti.U.S. Yellow E. L. B.T.Ti.U.S. User's Manual U17246EJ2V0UM 69 CHAPTER 5 DEBUG FUNCTION 5. 13 Snapshot Function The snapshot function is used to save the contents of registers, memory, and IOR/SFR of the user program execution process to the trace memory as snap data. This section explains the following items: - Snapshot event conditions - Snap data 5. 13. 1 Snapshot event conditions A snapshot event condition specifies the trigger by which a snapshot is to be executed. Snapshot event conditions are set in the Snap Shot dialog box. (Refer to "5. 12 Event Function".) Figure 5-24 Snap Shot Dialog box 5. 13. 2 Snap data One snap event condition can specify the collection of up to 16 snap data. The following types of data can be collected as snap data. - Register value - IOR/SFR value - Memory contents 70 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 14 Stub Function The stub function is used to execute the user program (sub-program) that has been downloaded or written to a vacant memory area in advance when an event occurs. Caution Append the jmp [r31] instruction [V850] or RETB instruction [78K] to the end of the sub-program that is executed when a stub event occurs, otherwise, malfunction may occur. This section explains the following items: - Setting stubevent conditions - Flow of stub function 5. 14. 1 Setting stubevent conditions A stub event condition specifies the trigger by which the stub function is executed. Stub event conditions are set in the Stub dialog box. (Refer to "5. 12 Event Function".) Figure 5-25 Setting Stub Function Conditions The start address of the function executed when a stub event occurs is as follows. Table 5-17 Start Address of Function to Be Executed (Stub Function) Device [V850] [78K] Setting Range 0 <= Start address of function <= 0xFFFFFFFF 0 <= Start address of function <= 0xFFFF User's Manual U17246EJ2V0UM 71 CHAPTER 5 DEBUG FUNCTION 5. 14. 2 Flow of stub function A flow of stub function is shown below. Figure 5-26 Flow of Stub Function Main program Sub-program (1) (4) (5) (3) (6) (2) jmp [r31] instruction [V850] RETB instruction [78K] (1) If stub function is not used (1) and (2) are executed. (2) If stub function is used 1) 2) 3) (1) is executed. A stub event occurs in (3) and a break occurs. The simulator sets the current address to the r31 register in (4), and rewrites the PC value to the entry address of the sub-program. [V850] The simulator forms a call stack in the current PC in (4), and rewrites the PC value to the entry address of the sub-program. [78K] 4) 5) (5) is executed. Execution is returned to the main program by the jmp instruction at the end of the sub-program in (6). 72 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 15 RAM Sampling Function The RAM sampling function is used to display in real time the variables and data allocated in the sampling range in the Watch window, Memory window, and IOR/SFR window. The sampling range depends on the simulator, but the variables and data allocated to the range shown in the following table can be displayed in real time. When using the RAM sampling function, set the sampling time in the Extended Option dialog box. Table 5-18 Sampling Range Product Name SM+ Internal RAM Real-Time Display Range Table 5-19 Address Target Area and Effective Size Product Name SM+ Target Area Internal RAM Effective Size (Bytes) 1K Start Address Alignment Not aligned User's Manual U17246EJ2V0UM 73 CHAPTER 5 DEBUG FUNCTION 5. 16 Load/Save Function SM+ allows saving and loading the following types of information as files. As a result, recovery of these various types of information is possible. Remark The simple window status can be maintained by selecting [Window] menu -> [Static]. (Refer to "5. 17. 1 Active status and static status".) This section explains the following items: - Debugging environment (project file) - Window display information (view file) - Window setting information (setting file) 5. 16. 1 Debugging environment (project file) A project file (*.prj) is a file that records the debugging environment. A project file is created when the debugging environment at a particular point in time is saved, and that debugging environment can be restored by loading this file at a subsequent time. Project files are loaded and saved in the Project File Save dialog box and the Project File Load dialog box, respectively. To load a project file at startup, press the 74 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION (2) Contents saved to project File The following contents are saved to the project file: Table 5-20 Contents Saved to Project File Window Name Debugger block Configuration dialog box main window All items (target device, clock setting, mapping information, simulator configuration file information) Display position, toolbar/status bar/button display information, execution mode information, trace on/off information, and coverage on/off information File information to be downloaded Set information Display information of window Display information of window, display start address Display information of window Saved Contents (Basic Level) Download dialog box Extended Option dialog box Debugger Option dialog box Source window Assemble window Memory window Stack window IOR/SFR window Local Variable window Trace window Event Manager Coverage window Console window Expansion window Event dialog box Event Link dialog box Break dialog box Trace dialog box Snap Shot dialog box Stub dialog box Timer dialog box Register window Watch window Add I/O Port dialog box DMM dialog box Delay Count dialog box Simulator block main window Display information of window, event information Display information of window, link event information Display information of window, break event information Display information of window, trace event information Display information of window, snapshot event information Display information of window, stub event information Display information of window, timer event information Display information of window Display information of window, watch registration information Added I/O port information DMM information Delay count value Position, size, and status of window User's Manual U17246EJ2V0UM 75 CHAPTER 5 DEBUG FUNCTION Window Name Signal Data Editor window Saved Contents (Basic Level) Position, size, and status of window Contents of Signal data files (*.wvi, *.wvo) currently being edited (when saved file exists) Position, size, and status of window Pin setting information Position, size, and status of window Size setting information for standard I/O buffer Standard library interface setting information Position, size, and status of window Contents of Serial transmission data file (*.ser) currently being edited (when saved file exists) Position, size, and status of window Contents of connected parts file currently being edited (when saved file exists) Timing Chart window Standard I/O window Serial window I/O Panel window 76 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 16. 2 Window display information (view file) A view file is a file that records window display information. View files can be loaded and saved for each window. When a view file is loaded, a reference window (Source window in the static status) is displayed and the display information at the time of saving is displayed. View files are loaded and saved in the View File Load dialog box and the View File Save dialog box, respectively. Table 5-21 Type of the View Files Target Window File Name Source window View file of the Source window Assemble window View file of the Assemble window Memory window View file of the Memory window Watch window View file of the Watch window Register window View file of the Register window IOR/SFR window View file of the IOR window IOR/SFR window View file of the SFR window Local Variable window View file of the Local Variable window Stack window View file of the Stack window Trace window View file of the Trace window Coverage window View file of the Coverage window Console window View file of the Console window All files Source fileNote Text file File Type Source Text (*.svw) Assemble (*.dis) Memory (*.mem) Watch (*.wch) Register (*.rgw) I/O Register (*.ior) [V850] SFR (*.sfr) [78K] Local Variable (*.loc) Stack Trace (*.stk) Trace (*.tvw)* Coverage (*.cov) Console (*.log) All (*.*) Source (*.c, *.s, *.asm) (During downloading) Text (*.txt) Note The extension of the source file can be changed in the Extended Option dialog box. User's Manual U17246EJ2V0UM 77 CHAPTER 5 DEBUG FUNCTION 5. 16. 3 Window setting information (setting file) A setting file is a file that records the window setting information (watch data settings, IOR/SFR settings, and event settings). Setting files can be loaded and saved for each window. When a setting file is loaded, the target window is displayed and the setting information that was saved is restored. Setting files are loaded and saved in the Environment Setting File Load dialog box and the Environment Setting File Save dialog box, respectively. Table 5-22 Type of the Setting Files Target Window File Name Watch window Setting file of the Watch window IOR/SFR window View file of the IOR window IOR/SFR window View file of the SFR window Event Manager Setting file of event File Type Watch (*.wch)Note I/O Register (*.ior) [V850] Note SFR (*.sfr) [78K] Note Event (*.evn) Note A variable value can not be loaded. 78 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 17 Functions Common to Each Window The windows have the following common functions. - Active status and static status - Jump function - Trace result with linking window - Drag & drop function 5. 17. 1 Active status and static status The Source window that is displaying the source file to which symbol information is read, Assemble window, Memory window and Coverage window has two statuses: Only one window can be opened in the active status. However, because two or more windows in the static status can be opened, the current status of the windows can be temporarily held. Select this status by the [Window] menu. (1) Active status The display position and contents of the window in the active status are automatically updated in association with the current PC value. This window is also the jump destination of the jump function. If this window is linked with the Trace window, the contents displayed in the active window are updated in association with the Trace window. Only one window can be opened in the active status. (2) Static status The display position of the window in the static status does not move in association with the current PC value, but the displayed contents are updated. The static window is not used as the jump destination of the jump function. In addition, it is not linked with the Trace window. If an active window is already open, the next window is opened in the static status. Two or more static windows can be opened at the same time. User's Manual U17246EJ2V0UM 79 CHAPTER 5 DEBUG FUNCTION 5. 17. 2 Jump function The jump function is used to jump to Source window, Assemble window, Memory window or Coverage window from a jump pointer that is the line or address on which the cursor is placed, and display the contents of the jump destination window from the jump pointer. You can jump among the above windows, or from Trace window, Stack window, Event Manager and Register window to the above windows. (1) Jump method The jump method is as follows: 1) Move the cursor to the line or address that is to be used as the jump pointer, on the window from which jumping is possible (select an event icon on the Event Manager). 2) Select the following menu item to which execution is to jump from the [Jump] menu. Source window -> Select [Source Text] Assemble window -> Select [Assemble] Memory window -> Select [Memory] Coverage window ->Select [Coverage] Remark If a program code does not exist on the line at the cursor position, the first address of the line with a program code above or below that line is used as the jump pointer. (2) Details of jump source address The details of jump source address is as follows: Table 5-23 Details of Jump Source Address Target Window From the Register window From the Memory window From the Event Manager Details of Jump Pointer Registers selected (The PC address width changes when memory banks are used. [78K0]) Address at the cursor position If the selected event icon is that of an event condition, an address condition is used as the jump pointer. If the address condition is set in point If the address condition is set in range If the address condition is set in bit Jump to specified address Jump to lower address (point address before the mask if a mask is specified) Jump to address at the bit position 80 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION Target Window From the Stack window Details of Jump Pointer A function at the cursor position that stack flame number indicates is used as the jump pointer. With current function If the jump destination is the Source window Other than above Jumps to the current PC line Jumps to the current PC address With function other than current function If the jump destination is the Source window Other than above Jump to the line that calls a nested function. Jump to the address next to the instruction that calls a nested function. From the Trace window Jump to the Memory window or Coverage window If the cursor position is at an access address, access data, or access status Other than above Access address Fetch address Jump to the Source window or Assemble window Fetch address User's Manual U17246EJ2V0UM 81 CHAPTER 5 DEBUG FUNCTION 5. 17. 3 Trace result with linking window By linking Trace window with each window (Source window, Assemble window, Memory window or Coverage window), the corresponding part can be displayed on the linked window, by using the address at the cursor position on the Trace window as a pointer. If the cursor is moved on the Trace window, the corresponding part on the linked window is highlighted or indicated by the cursor position. (1) Linking method 1) 2) Set the Trace window as the current window. Select [View] menu -> [Window Synchronize] to select a window to be linked. Source window -> Select [Source Text] Assemble window -> Select [Assemble] Memory window -> Select [Memory] Coverage window -> Select [Coverage] 3) 4) Move the cursor to the line to be linked in the trace result display area of the Trace window. Using the address of the line selected in 3 as a pointer, the corresponding part is highlighted (or indicated by the cursor position) in the display area of the window selected in 2. Remark The linking source address differs as follows depending on the cursor position in the trace result display area if the Memory window or Coverage window is linked. Access address, access data, access status -> Access address Others -> Fetch address When the Source window or Assemble window is linked, the fetch address is always used as the pointer. 82 User's Manual U17246EJ2V0UM CHAPTER 5 DEBUG FUNCTION 5. 17. 4 Drag & drop function Selected and highlighted line numbers, addresses, and text can be dragged and dropped in another window using the following method. 1) Drag the selected line number, address, or text. -> The shape of the mouse cursor changes from an arrow to "-". 2) Drop the selection in a window or area where it can be dropped. -> The shape of the cursor changes from "-" to "OK" when the cursor is placed over a window or area where the selection can be dropped. In the window in which the line number of the address has been dropped, an operation is performed on the dropped address or the address that is obtained from the dropped line number. For example, a variable can be simply registered by dragging and dropping in the Watch window such a variable located in the Source window. (1) Drag & drop details The operation to be performed after dropping the line number or address differs, depending on the window or area in which the line number or address has been dropped. Table 5-24 Details of Drag & Drop Function (Line/Address) Window/Area to Drop to The Event Manager or the event manager area in each various event setting dialog box Operation After Drop Automatically creates an execution event condition by using the dropped line number or address as an address condition. Event condition names are automatically created as Evt00001, Evt00002, and so on. A path count is not specified. The address condition is set for the closest symbol in the format of symbol name + offset value. Automatically creates an execution event condition by using the dropped line number or address as an address condition. The automatically created event condition is set in each condition setting area in which the line number or address has been dropped. Event condition names are automatically created as Evt00001, Evt00002, and so on. A path count is not specified. The address condition is set for the closest symbol in the format of symbol name + offset value. The text of the dropped line number or address is set in the area in which the line number or address has been dropped. The address condition is set for the closest symbol in the format of symbol name + offset value. Condition setting area in each various event setting dialog box (other than address and data setting areas) Condition setting area in each various event setting dialog box (address and data setting areas) User's Manual U17246EJ2V0UM 83 CHAPTER 5 DEBUG FUNCTION Table 5-25 Details of Drag & Drop Function (Character String) Window/Area to Drop to The Event Manager or the event manager area in each various event setting dialog box Operation After Drop If the dropped text can be converted as a symbol into an address value, an event condition in the Access status (all access statuses) or Execute status is automatically created, using the converted address value as an address condition. Event condition names are automatically created as Evt00001, Evt00002, and so on. A data condition and path count are not specified. The address condition is set by the dropped text. The relationship between the event condition to be created and the symbol is as follows: Symbols Variable Function Symbol in data section Symbol in code section Others Condition setting area in each various event setting dialog box (other than address and data setting areas) Status Access(R/W) Execute Access(R/W) Execute Access (R/W) If the dropped text can be converted as a symbol into an address value, an event condition in the Access status (all access statuses) or Execute status is automatically created, using the converted address value as an address condition. The automatically created event condition is set in each condition setting area in which the line number or address has been dropped. Event condition names are automatically created as Evt00001, Evt00002, and so on. A data condition and path count are not specified. The address condition is set by the dropped text. The relationship between the event condition to be created and the symbol is as follows: Symbols Variable Function Symbol in data section Symbol in code section Others Status Access(R/W) Execute Access (R/W) Execute Access (R/W) Condition setting area in each various event setting dialog box (address and data setting areas) Watch window The dropped text is set in the area. If the dropped text is recognizable as a symbol, the contents of the symbol are displayed. Remark The various event setting dialog boxes include the Event dialog box, Event Link dialog box, Break dialog box, Trace dialog box, Snap Shot dialog box, Stub dialog box and Timer dialog box. 84 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION CHAPTER 6 SIMULATION FUNCTION This chapter explains the following simulation function. These are provided in SM+ simulator block. Table 6-1 Simulation Function List Item Pin input function , pin output function Standard I/O function, file I/O function Serial I/O function A dummy target system can be created 6. 1 Pin I/O Function 6. 2 Standard I/O Function 6. 3 Serial I/O Function 6. 4 Panel Function Refer To User's Manual U17246EJ2V0UM 85 CHAPTER 6 SIMULATION FUNCTION 6. 1 Pin I/O Function This section explains the following items related to the pin I/O function: - Pin input - Pin output - Pin selection - Data search - Signal data files (*.wvi, *.wvo) 6. 1. 1 Pin input Pin input data is created in the Signal Data Editor window. Pin input can be simulated by inputting the created signal data to the simulator from the Signal Data Editor window. Figure 6-1 Creation of Pin Input Data 86 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION 6. 1. 2 Pin output Pin output data is displayed in the Timing Chart window. In the Timing Chart window, inputs and output/output to the pins currently being simulated can be checked by performing waveform display of the pin output data. However, the amount of data that can be displayed at one time is limited. Figure 6-2 Display of Pin Output Data 6. 1. 3 Pin selection The pin to be displayed in the Signal Data Editor window and the Timing Chart window is selected in the Select Pin dialog box. The pin information set in the Select Pin dialog box can be saved and recovered as a pin information file (*.pin). Figure 6-3 Pin Selection User's Manual U17246EJ2V0UM 87 CHAPTER 6 SIMULATION FUNCTION 6. 1. 4 Data search A detailed search of display data can be performed from the Search Data dialog box displayed by selecting [Edit] menu -> [Search...] in the Timing Chart window. Figure 6-4 Detailed Data Search 6. 1. 5 Signal data files (*.wvi, *.wvo) Signal data files are CSV-format text files used in the Signal Data Editor window and the Timing Chart window. These files can be edited and managed using a commercially available editor that supports the CSV-format . Signal data files can be saved and recovered by selecting [Simulator] menu -> [Save As.../Open...] in the respective windows. (1) File details Signal data files consist of the following three parts. 1.Comment part 2.Option setting part Additional information is described for the various options in the option setting part. Almost all the information can be omitted, except for the pin name setting information. When an option is omitted, its default setting is used. 3.Signal data setting part The data corresponding to the pins for which pin name setting information has been set is described in chronological order in the signal data setting part. The data description order is the same as the data order in the Signal Data Editor window. 88 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION Figure 6-5 Signal Data File Outline # Option settings OPT, VERSION, version number OPT, PIN_NAME, pin name 1, pin name 2, ..., pin name n OPT, PIN_ALIAS, pin 1 display name, pin 2 display name, ..., pin n display name OPT, PIN_TYPE, pin 1 type, pin 2 type, ..., pin n type OPT, PIN_INPUT, pin 1 input, pin 2 input, ..., pin n input OPT, TIME_UNIT, time unit 1. --------2-1 --------2-2 --------2-3 --------2-4 --------2-5 --------2-6 2. #Signal data Loop information 1, wait time 1, signal value 1 of pin 1, signal value 1 of pin 2, ..., signal value 1 of pin n Loop information 2, wait time 2, signal value 2 of pin 1, signal value 2 of pin 2, ..., signal value 2 of pin n 3. .......................... Loop information m, wait time m, signal value m of pin 1, signal value m of pin 2, ...,signal value m of signal n (2) File format details Table 6-2 File Format Details (Signal Data File) Item 1. Comment part Syntax Description # Part after # until line end = comment . Description 2. Option setting part Syntax Description OPT, option name, information for each option If option settings are required, specify the option name and the required data. The option items can be specified in any order. Option types and the operation when options are omitted are as described below ( 2-1 Format version to 2-6 Time unit setting information). 2-1 Format version Syntax Description When omitted OPT, VERSION, version number Indicates the format version of this file. Processing is performed assuming the latest file format version. 2-2 Pin name information Syntax Description When omitted OPT, PIN_NAME, pin name 1, pin name 2, ..., pin name n Specify each pin name. For the pin names, refer to the user's manual of the device. Cannot be omitted. 2-3 Pin display name information Syntax Description When omitted OPT, PIN_ALIAS, pin 1 display name, pin 2 display name, ..., pin n display name Specify the display name of each pin. The pin name is displayed. 2-4 Pin type information (analog pin/digital pin information) User's Manual U17246EJ2V0UM 89 CHAPTER 6 SIMULATION FUNCTION Item Syntax Description OPT., PIN_TYPE, pin 1 type, pin 2 type, Set the type of the pin. ANALOG DIGITAL When omitted Analog pin Digital pin Description , pin n type Treated as a digital pin. 2-5 Signal input enable/disable Syntax Description OPT, PIN_INPUT, pin 1 input, pin 2 input, ..., pin n input Enable/disable signal input for each pin. VALID INVALID When omitted Enable pin input Disable pin input Pin input is enabled. 2-6 Time unit setting information Syntax Description OPT, TIME_UNIT, time unit Set the Wait time unit for signal data. MAINCLK USEC MSEC When omitted Main clock Microsecond Millisecond MAINCLK is used as the time unit. 3. Signal data setting part Syntax Description Loop information, wait time, pin 1 signal value, pin 2 signal value, ..., pin n signal value Value of pin (1-n) changes following lapse of wait time. a)Loop information S S- value E b) Wait time Specify value of 0 to 4,294,967,295 as a decimal integer. c) Signal data Specify the corresponding pin data as a decimal integer. Analog value Digital value 0 - 5000 0 or 1 Loop start position (infinite loop) Loop start position (with loop count) Loop end position 90 User's Manual U17246EJ2V0UM ... CHAPTER 6 SIMULATION FUNCTION (3) Description example Figure 6-6 Description Example (Signal Data File) # Option settings OPT,VERSION,1.00 OPT,PIN_NAME,P10,P11,P12,P13,P14,P15,A NI0 OPT,PIN_ALIAS,,,,,,,Analog 1 OPT,PIN_TYPE,,,,,,,ANALOG OPT,PIN_INPUT,,,,,,,INVALID OPT,TIME_UNIT,MAINCLK #Signal data ,100,0,0,0,0,0,0,1250 ,100,0,0,0,0,0,1,1250 S-10,100,0,0,0,0,1,0,2500 ,100,0,0,0,0,1,1,3750 ,100,0,0,0,1,0,0,5000 E,100,0,0,0,1,0,1,5000 ,100,0,0,0,1,1,0,5000 ,100,0,0,0,1,1,1,5000 ,100,0,0,1,0,0,0,5000 ,100,0,0,1,0,0,1,5000 ,100,0,0,1,0,1,0,5000 User's Manual U17246EJ2V0UM 91 CHAPTER 6 SIMULATION FUNCTION 6. 2 Standard I/O Function A standard I/O function and file I/O function are provided for user programs to be debugged. The window that provides this function is the Standard I/O window. Text display of standard output data and keyboard input of standard input data is possible. The maximum number of lines that can be displayed can be set in the Standard I/O Buffer Size dialog box. Execute the following procedure to use this function. Figure 6-7 Standard I/O Function This section explains the following items: - Standard I/O and File I/O Usage Procedure - Load module creation procedure - GUI manipulation procedure - Function specifications 92 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION 6. 2. 1 Standard I/O and File I/O Usage Procedure The following procedure must be executed in order to call the standard I/O and file I/O functions in a user program. Figure 6-8 Standard I/O and File I/O Usage Procedure Create source program 1) 2) Create load module GUI manipulation 3) GUI manipulation Standard I/O window 1) Input descriptions for calling standard I/O and file I/O functions in the user source program. (Refer to "6. 2. 4 Function specifications".) 2) 3) Create a load module. (Refer to "6. 2. 2 Load module creation procedure".) Perform the necessary GUI manipulation. (Refer to "6. 2. 3 GUI manipulation procedure".) User's Manual U17246EJ2V0UM 93 CHAPTER 6 SIMULATION FUNCTION 6. 2. 2 Load module creation procedure Link manipulation must be performed to use the standard I/O and file I/O functions. The load module creation procedure is shown in the following. - In the case of CA850 - In the case of CC78K0 + RA78K0, or CC78K0S + RA78K0S (1) In the case of CA850 Figure 6-9 Load Module Creation Procedure (CA850) 1) ..... sub() { printf(...); } ...... libsmplus.a 2) Link Link directive file Load module Compile Source Program User object 1) Library addition The I/O library supporting the simulator (libsmplus.a) must be linked. Caution Link the I/O library (libsmplus.a) before the library (libc.a). 2) Link directive file change Place the section (ptio.data) in any external memory area. The area where this section is placed is called the interface area, and its beginning is called the interface address. The size of the interface area is 20 bytes. When the interface address is 0x20000, a placement command line such as the following is added to the link directive file. Example of added description when the interface address is 0x20000 ......... PTIODATA : !LOAD ?RW V0x200000 L0x14 A0x4 { ptio.data = $PROGBITS ?AW ptio.data }; ......... 94 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION (2) In the case of CC78K0 + RA78K0, or CC78K0S + RA78K0S Figure 6-10 Load Module Creation Procedure (CC78K0 + RA78K0, or CC78K0S + RA78K0S) 1) Library ..... sub() { printf(...); } ...... 2) stdio_smplus.h 3) Link Link directive file Load module Compile Source Program User object 1) Library addition The I/O library supporting the simulator must be linked. (Refer to "Table 6-3 I/O Libraries for Simulator")The following types of I/O libraries for the simulator are available according to the compilation mode. Refer to the compiler and assembler user's manuals for the compilation modes. Caution Link the I/O library before the standard library. Table 6-3 I/O Libraries for Simulator Library Name Description of Compilation Mode CC78K0, RA78K0 [78K0] smplus0.lib smplus0o.lib smplus0r.lib smplus0e.lib smplus0oe.lib smplus0re.lib CC78K0S, RA78K0S [78K0S] smplus0s.lib smplus0sr.lib Normal model Normal model, Pascal function call Normal model Normal model, old function interface Normal model, Pascal function call Normal model, flash memory supported Normal model, old function interface, flash memory supported Normal model, Pascal function call, flash memory supported User's Manual U17246EJ2V0UM 95 CHAPTER 6 SIMULATION FUNCTION 2) Addition of header file Include the simulator header file (stdio_smplus.h) instead of the standard header file (stdio.h). 3) Link directive file addition Place the section (PTIODATA) in any memory area. The area where this section is placed is called the interface area, and its beginning is called the interface address. The size of the interface area is 20 bytes. Describe as follows in the link directive file when the interface address is 0x0f000. Example of description when the interface address is 0x0f000 MEMORY PTIOMEM:(0F000H, 14H) MERGE PTIODATA:COMPLETE=PTIOMEM 6. 2. 3 GUI manipulation procedure The GUI manipulation procedure for using the standard I/O and file I/O functions is described below. 1) Memory mapping setting Map the range that includes the interface area set in "6. 2. 2 Load module creation procedure" as the target attribute in the Configuration dialog box displayed by selecting [Option] menu -> [Configuration...]. Remark This setting is required in SM+ for V850. 78K0S. 2) Interface address and I/O file path setting Set the interface address and I/O file path in the Simulator Option dialog box displayed by selecting [Option] menu -> [Simulator Option...]. 3) Output data display and input data input Data display of standard output and standard error output, as well as input of standard input data can be performed in the Standard I/O window displayed by selecting [Simulator] menu -> [Standard I/O]. 6. 2. 4 Function specifications It is not necessary in SM+ for 78K0 or SM+ for The usable functions and specifications are displayed. - printf - scanf - fopen - fclose - fprintf - fscanf 96 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION Table 6-4 Function Specifications (Standard I/O, File I/O Related) Function printf Formatted output Format Return value Explanation int printf(const char* format [, arg, ...]); Output character count is returned. The format specified by the character string format is applied to each of the aguments arg, and the formatted data output as a result is output to stdout. Floating points (%f, %e, %E, %g, %G) cannot be used in the format character string. Description scanf Formatted input Format Return value int scanf(const char* format [, arg, ...]); The number of input fields for which scanning, conversion, and saving were performed normally is returned. Already scanned fields that were not saved are not included. If read was attempted at the end of the file, EOF is returned. The input to be converted is read from standard I/O stdin in accordance with the format specified by the character string format, with the arguments arg that follow the character string format handled as objects that store the converted input. Floating points (%f, %e, %E, %g, %G) cannot be used in the format character string. Explanation fopen File open Format Return value Explanation FILE* fopen(const char* filename, const char* mode); The opened file pointer is returned. When an error occurs, the NULL pointer is returned. The file specified by filename is opened. Specify the access modes indicated below for mode. "r" "w" "a" Opens files in the read mode. An error occurs if the file does not exist or cannot be found. Opens an empty file in the write mode. The file contents are destroyed if the specified file already exists. Opens files in the write mode to the end of the file without deleting the EOF marker before writing new data to a file (add mode). Creates a file if no file exists. Opens files in both the read and write modes (existing files). Opens an empty file in both the read and write modes. The file contents are destroyed if the specified file already exists. Opens files in both the read and add modes. When an addition is made, the EOF marker is deleted before new data is written to the file. Also, the EOF marker is restored upon write completion. Not created if no file exists. "r+" "w+" "a+" User's Manual U17246EJ2V0UM 97 CHAPTER 6 SIMULATION FUNCTION Function fclose File close Format Return value Explanation fprintf int fclose(FILE* stream); Description 0 is returned. If an error occurs, EOF is returned. Closes stream. However, this does not apply to the stdout, stderr, and stdin standard I/Os. Formatted file output Format Return value Explanation int fprintf(FILE* stream, const char* format, [, arg, ...]); The output character count is returned. The format specified by the character string format is applied to each of the aguments arg, and the formatted data output as a result is output to stream. The items that can be specified for stream consist of the pointers of the files opened by the stdout, stderr, and fopen functions. Floating points (%f, %e, %E, %g, %G) cannot be used in the format character string. fscanf Formatted file input Format Return value int fscanf(FILE* stream, const char* format, [, arg, ...]); The number of input fields for which scanning, conversion, and saving were performed normally is returned. Already scanned fields that were not saved are not included. If read was attempted at the end of the file, EOF is returned. The input to be converted is read from stream in accordance with the format specified by the character string format, with the arguments arg that follow the character string format handled as objects that store the converted input. The items that can be specified for stream consist of the pointers of the files opened by the stdin and fopen standard I/O functions. Floating points (%f, %e, %E, %g, %G) cannot be used in the format character string. Explanation 98 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION 6. 3 Serial I/O Function Data input to the serial reception pin of the device and data output from the transmission pin can be acquired as the serial I/O function. The window that provides this function is the Serial window. Serial window functions as the communication partner of the incorporated serial interface, displaying transmission/reception data in the top part of the window, with data creation and data transmission performed in the bottom part of the window. Figure 6-11 Serial I/O Function Data display Data creation and transmission This section explains the following items: - Format setting - Serial log data file (*.log) - Serial transmission data file (*.ser) User's Manual U17246EJ2V0UM 99 CHAPTER 6 SIMULATION FUNCTION 6. 3. 1 Format setting The format is set either in the Format (UART) dialog box or the Format (CSI) dialog box, according to the serial interface selected in the Serial window. 6. 3. 2 Serial log data file (*.log) The serial log data file is a CSV-format text file that saves the Log display area information for transmission/ reception data in the Serial window. This file can be referenced with a commercially available editor that supports the CSV format. The serial log data file can be saved by selecting [File] menu -> [Save/Save As...] in the Serial window. The serial log data file is used only to save information and cannot be read to the simulator. The file details are described below. (1) File details The transmission/reception data are saved in chronological order in the serial log data file. The saved contents are the same as the data array in the log display area in the Serial window. Figure 6-12 Serial Log Data File Outline OPT, SERIAL_NAME, serial name OPT, TIME_UNIT, time unit time1, send data1, receive data1, status1 time2, send data2, receive data2, status2 1. 2. 3. (2) File format datails Table 6-5 File Format Details (Serial Log Data File) Item Description 1. Serial name Syntax Description 2. Time unit Syntax Description OPT, TIME_UNIT, time unit Time unit MAINCLK USEC MSEC 3.Transmission/reception data Syntax time, send data, receive data, status Main clock Microsecond Millisecond OPT, SERIAL_NAME, serial name Name of serial interface selected in the Serial window 100 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION Item Description a)Time Description Time from end of transmission/reception of previous data until end of current transmission/ reception. The time unit is the unit specified by OPT, TIME_UNIT. The log data time output first is always 0. b) Send data Displays the data sent from the Serial window side (data received by the CPU side). c) Receive data Displays the data received from the Serial window side (data sent by the CPU side). d) Status data Displays the status at reception. If an error occurs, the following characters are displayed. Nothing is displayed when there is no error. P F (3) Saving example Figure 6-13 Saving Example (Serial Log Data File) OPT,SERIAL_NAME,SIO31 OPT,TIME_UNIT,MAINCLK 256,0x32,0xb7, 256,0x64,0xe9, 256,0x96,0x1b, 256,0xc8,0x4d, 256,0xfa,0x7f,P 256,0x2c,0xb1, Parity error (parity bit mismatch) Framing error (stop bit not detected) User's Manual U17246EJ2V0UM 101 CHAPTER 6 SIMULATION FUNCTION 6. 3. 3 Serial transmission data file (*.ser) Serial transmission data files are CSV-format text files that handle the contents of the Serial editor area in the Serial window and the information of the Format (UART) dialog box and the Format (CSI) dialog box. These files can be edited and managed using a commercially available editor that supports the CSV format . Data can be saved to such a file by clicking the 2. 3. Figure 6-15 Serial Transmission Data File Outline: CSI # Option settings OPT, VERSION, version number OPT, SERIAL_NAME, serial name OPT, SERIAL_FORMAT, serial type OPT, REPEAT, repeat information OPT, TIME_UNIT, time unit OPT, FIRST_BIT, the first bit of data OPT, DATA_LENGTH, data bit length OPT, MASTER_SLAVE, transfer mode OPT, TRANSFER_CLOCK, transfer clock OPT, DATA_PHASE, data phase OPT, CLOCK_PHASE, clock phase #Send data wait1, data type1, send data1, wait2, data type2, send data2, 1. --------2-1 --------2-2 --------2-3 --------2-4 --------2-5 --------2-6 --------2-7 -------2-11 -------2-12 -------2-13 -------2-14 2. 3. 102 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION (2) File format details Table 6-6 File Format Details (Serial Transmission Data File) Item 1. Comment part Syntax Description # Part after # until line end = comment . Description 2. Option setting part Syntax Description OPT, option name, information for each option If option settings are required, specify the option name and the required data. The option items can be specified in any order. Option types and the operation when options are omitted are as described below (" 2-1 Format version" to " 2-14 Clock phase"). 2-1 Format version Syntax Description When omitted 2-2 Serial name Syntax Description When omitted 2-2 Serial type Syntax Description OPT, SERIAL_FORMAT, serial type Specify the serial interface type. UART CSI When omitted In the case of the asynchronous serial interface (UART) In the case of the 3-wire serial interface (CSI) OPT, SERIAL_NAME, serial name Specify the name of the serial interface to be used for communication. For the name, refer to the user's manual of the device to be used. The serial interface selected in the Serial window is used. OPT, VERSION, version number Indicates the format version of this file. Processing is performed assuming the latest file format version. The serial interface type selected in the Serial window is used. 2-4 Repeat transfer Syntax Description OPT, REPEAT, repeat information Specify whether to return to the beginning and continue sending data, after the last data has been sent during automatic transmission. ON OFF When omitted Repeat transmission Stop transmission after last data has been sent Transmission stops (OFF) after the last data has been sent. 2-5 Time unit setting information Syntax OPT, TIME_UNIT, time unit User's Manual U17246EJ2V0UM 103 CHAPTER 6 SIMULATION FUNCTION Item Description Specify the signal data wait time unit. MAINCLK USEC MSEC When omitted Main clock Microsecond Millisecond Description MAINCLK is used as the time unit. 2-6 Transfer direction Syntax Description OPT, FIRST_BIT, first bit of data Specify the first bit of transmission data. MSB LSB When omitted In the case of MSB first In the case of LSB first LSB if the serial type is UART, and MSB if the serial type is CSI 2-7 Data bit length Syntax Description When omitted OPT, DATA_LENGTH, data bit length Specify the bit length of the transmission data as an integer. The maximum valid value that can be set is 32. 7 if the serial type is UART, and 8 if the serial type is CSI 2-8 Baud rate value Syntax Description When omitted OPT, BAUDRATE, baud rate value Specify the baud rate value as an integer. (Unit: bps) Cannot be omitted. (Communication is not possible when this item is omitted.) 2-9 Stop bit length Syntax Description When omitted OPT, STOP_LENGTH, bit length of stop bit Specify the bit length of the stop bit as an integer. 1 is used as the bit length. 2-10 Parity information Syntax Description OPT, PARITY, parity information Specify the parity information. NONE_PARITY ODD_PARITY EVEN_PARITY ZERO_PARITY When omitted No parity Odd parity Even parity 0parity No parity (NONE_PARITY) is used. 2-11 Transfer mode Syntax OPT, MASTER_SLAVE, transfer mode 104 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION Item Description Description Specify the transfer mode on the Serial window side. MASTER SLAVE Master mode Slave mode When omitted The slave mode (SLAVE) is used on the Serial window side. 2-12 Transfer clock Syntax Description When omitted 2-13 Data phase Syntax Description OPT, DATA_PHASE, data phase Specify the data phase. NORMAL_DATA PRECEDE_DATA When omitted NORMAL_DATA Normal 3-wire serial transmission/reception timing Transmission/reception timing half a clock of the operation clock earlier than the normal 3-wire serial transmission/reception timing OPT, TRANSFER_CLOCK, transfer clock Specify the transfer clock (unit: Hz). This setting is required in the master mode. This item cannot be omitted in the master mode. 2-14 Clock phase Syntax Description OPT, CLOCK_PHASE, clock phase Specify the clock phase. NORMAL_CLOCK REVERSE_CLOCK When omitted 3. Signal data Syntax wait, data type, send data NORMAL_CLOCK The operation clock in normal clock phase (starting from falling edge) Operation clock in reverse clock phase (starting from rising edge) User's Manual U17246EJ2V0UM 105 CHAPTER 6 SIMULATION FUNCTION Item Description Description Specify the transmission timing and transmission data. a)Wait Specifies the time from the completion of transmission of the immediately previous data until the start of transmission of next data. The time unit is the unit specified by OPT, TIME_UNIT. This item is valid during transmission from the (3) Description example Figure 6-16 Description Example (Serial Transmission Data File) #Option setting OPT,VERSION,1.00 OPT,SERIAL_NAME,SIO31 OPT,SERIAL_FORMAT,CSI OPT,ROUND_TRANSFER,ON OPT,TIME_UNIT,MAINCLK OPT,FIRST_BIT,LSB OPT,BIT_LENGTH,8 OPT,MASTER_SLAVE,MASTER OPT,TRANSFER_CLOCK,625000 OPT,DATA_PHASE,NORMAL_DATA OPT,CLOCK_PHASE,NORMAL_CLOCK #Data 128,I,0x32, 128,I,0x64, 28,I,0x96, 128,I,0xc8, 106 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION 6. 4 Panel Function SM+ allows input manipulation and output display simulation by providing standard parts (connected parts) in which the I/O block for peripheral I/O designed as a GUI interface. The window providing this function is the I/O Panel window. A dummy target system can be created using this function. Buttons, LEDs, level gauges, etc., are provided as connected parts, and these parts can be freely connected to device pins. Regarding the display style, figure objects created with drawing tools can be used in addition to bitmaps. Figure 6-17 I/O Panel Window This section explains the following items: - Connected parts types - New creation and connection information settings - Simulation mode - Connection information list display - Operation after CPU reset User's Manual U17246EJ2V0UM 107 CHAPTER 6 SIMULATION FUNCTION 6. 4. 1 Connected parts types The connected parts offered by SM+ are listed below. Table 6-7 Connected Parts Description -> Properties Dialog Box Name Switch Can be connected to any pin. By clicking the displayed button, a value can be input to the connection pin. ->Parts Button Properties A key matrix consists of multiple pins connected in a matrix array, wherein each contact represents a key, and clicking a key results in a specific state. A key matrix can be connected to any pin, and data can be input using multiple keys. ->Parts Key Properties Used for inputting analog data such as power supply voltage. Any data within a given range can be set. Any value within a specified range can be assigned to a pin connected to an A/ D converter. ->Parts Level Gauge Properties Light Emitting Diode An LED can be connected to any pin, and the output from the pin can be indicated by switching the LED on or off. ->Parts Led Properties A product that consists of 7 LEDs configured to represent a numeric figure. When the output from the pin assigned to the digit signal is active, the corresponding 7-segment LED switches on or off. ->Parts Segment LED Properties A product that consists of 14 LEDs configured to represent an alphabetic character. When the output from the pin assigned to the digit signal is active, the corresponding 14-segment LED switches on or off. ->Parts Segment LED Properties A product that consists of multiple LEDs arranged in a matrix array. When the output from an assigned pin is active, the corresponding 14-segment LED switches on or off. ->Parts Matrix Led Properties A buzzer connected to a pin indicates the output information from the connected pin with a bitmap or a buzzer tone. ->Parts Buzzer Properties Whether a pin is connected to a pull-up/down resistor can be specified. ->Pull up/Pull down dialog box Figures, characters, and bitmaps can be connected to pins. ->Object Properties Connected Part Name Button Key matrix Level gauge LED 7-segment LED 14-segment LED Matrix LED Buzzer Pull-up/Pull-down setting Figure/character/bitmap 108 User's Manual U17246EJ2V0UM CHAPTER 6 SIMULATION FUNCTION 6. 4. 2 New creation and connection information settings A new connected part is created and placed by selecting [Parts] menu in the I/O Panel window, or by clicking the buttons on the Parts toolbar. As a result, the mouse cursor changes to "+" and placement in the window becomes possible. Connection information is set in the various properties dialog boxes displayed by double-clicking the connected parts created beforehand. (Refer to "Table 6-7 Connected Parts".) 6. 4. 3 Simulation mode The connected parts whose settings have been completed in the various properties dialog boxes are displayed in the I/O Panel window and become signal interface points during simulation. I/O results can be checked and input values can be fed to the simulator from these displayed parts. For details about manipulations using these connected parts, refer to the properties dialog box of each item. (Refer to "Table 6-7 Connected Parts".) Input simulation can be done by selecting [Figure] menu -> [Simulation Mode] in the I/O Panel window, as a result of which the mouse cursor changes to a hand shape. 6. 4. 4 Connection information list display List display of all the figure objects placed in the I/O Panel window and the part object pin connection statuses can be done by selecting [View] menu -> [Parts List...]. Object properties dialog boxes can be opened by double-clicking on the list, in order to change connection information. Figure 6-18 Connected Parts Information List User's Manual U17246EJ2V0UM 109 CHAPTER 6 SIMULATION FUNCTION 6. 4. 5 Operation after CPU reset The operations of the various connected parts when CPU reset has been executed from the debugger are listed in the following table. Table 6-8 Operation of Connected Parts after CPU Reset Connected Part Name Button Key matrix Level gauge LED 7-segment LED 14-segment LED Matrix LED Figure and connected part Not clicked status Key not clicked status Input value 0 status Display according to value of connected output pin. Display according to value of connected output pin. Display according to value of connected output pin. Display according to value of connected output pin. Display according to value of connected output pin. Operation after CPU Reset 110 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE CHAPTER 7 WINDOW REFERENCE This chapter explains in detail the functions of the windows and dialog boxes of SM+. - Window List - Explanation of Windows User's Manual U17246EJ2V0UM 111 CHAPTER 7 WINDOW REFERENCE 7. 1 Window List The list is the windows of the SM+. Table 7-1 Window List Window Name Window and Dialog box of Debugger block main window Contents This window is displayed first, when the SM+ is started. It controls execution of the user program. Various windows are opened from this window. Displays and sets the SM+ operation environment. Displays and sets the extended options of the SM+. Displays and sets other options. Saves the current debug environment to project file Loads the debug environment. Loads an object file and binary file. Saves the memory contents to a file. Lists the names of the downloaded load module files. Displays a source file and text file Searches in the Source window Specifies a file to be displayed in the Source window and the position from which displaying the file is to be started. Disassembles the program and executes online assembly. Searches in the Assemble window Specifies the start address to display the contents of the Memory window, Assemble window or Coverage window. Displays the address of the specified variable or function, or the value of the specified symbol Displays and changes specified watch data Displays temporarily specified watch data Registers watch data todisplay in the Watch window Changes watch data todisplay in the Watch window Displays and changes the local variable in the current function. Displays the current stack contents Display the contents of memory. Searches in the Memory window Fills the memory contents with specified data. Configuration dialog box Extended Option dialog box Debugger Option dialog box Project File Save dialog box Project File Load dialog box Download dialog box Upload dialog box Load Module List dialog box [V850] Source window Source Search dialog box Source Text move dialog box Assemble window Assemble Search dialog box Address move dialog box Symbol To Address dialog box Watch window Quick Watch dialog box Add Watch dialog box Change Watch dialog box Local Variable window Stack window Memory window Memory Search dialog box Memory Fill dialog box 112 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Window Name Memory Copy dialog box Memory Compare dialog box Memory Compare Result dialog box DMM dialog box Register window Register Select dialog box [V850] IOR/SFR window IOR/SFR Select dialog box Add I/O Port dialog box Timer dialog box Timer Result dialog box Trace window Trace Search dialog box Trace Data Select dialog box Trace move dialog box Trace dialog box Delay Count dialog box Coverage window Coverage Search dialog box Coverage-Clear dialog box Coverage-Address dialog box [V850] Coverage-Condition Setting dialog box Coverage-Efficiency View dialog box Event Manager Event dialog box Event Link dialog box Break dialog box Snap Shot dialog box Stub dialog box View File Save dialog box Copies the memory. Compares the memory. Contents Displays the results of comparing the memory. Sets addresses and data subject to DMM. Displays the contents of registers. Selects registers to be displayed in the Register window. Displays the contents of IOR/SFR Selects IOR/SFR and I/O ports to be displayed in the IOR/ SFR window Registers an I/O port to be displayed in the IOR/SFR window. Registers and sets timer event conditions, and displays execution time measurement result. Displays execution time measurement results. Displays trace results. Searches trace data. Selects items to be displayed in the Trace window. Specifies the start address to display the contents of the Trace window. Registers and sets trace event conditions. Sets the delay count of a delay trigger trace event. Display of coverage results Search of the Coverage window contents Clearing of the Coverage window Selection of coverage measurement range Setting of coverage efficiency measurement range Display of coverage result efficiency Displays, enables/disables, and deletes each event condition. Registers event conditions. Registers event link conditions. Registers and sets break event conditions. Registers and sets snapshot event conditions. Registers and sets stub event conditions. Saves the display information of the current window to a view file. User's Manual U17246EJ2V0UM 113 CHAPTER 7 WINDOW REFERENCE Window Name View File Load dialog box Environment Setting File Save dialog box Environment Setting File Load dialog box Reset Debugger dialog box Exit Debugger dialog box About dialog box Console window Font dialog box Browse dialog box Window and Dialog box of Simulator block Signal Data Editor window Loop dialog box Timing Chart window Select Pin dialog box Search Data dialog box Standard I/O window Standard I/O Buffer Size dialog box Simulator Option dialog box Serial window Format (UART) dialog box Format (CSI) dialog box I/O Panel window Parts Button Properties Parts Key Properties Parts Level Gauge Properties Parts Led Properties Parts Segment LED Properties Parts Matrix Led Properties Parts Buzzer Properties Pull up/Pull down dialog box Contents Loads the view file of each window. Saves the setting information of the current window to a setting file. Loads the setting file of each window. Initializes the SM+,CPU, and symbol information. Terminate the SM+. Displays the version of the SM+. Inputs commands. Displays the types of fonts displayed. Selects the file to be set Setting of input signal data Setting of loop information for the Signal Data Editor window Timing chart display of input and output signals Selection of display pins in the Signal Data Editor window and Timing Chart window Detailed search of the Timing Chart window Standard I/O Function window Specification of maximum number of display lines for the Standard I/O window Setting of simulator options Serial interface communication window Setting of serial format (UART) Setting of serial format (CSI) Creation of dummy target system Setting of button pin connection information Setting of key matrix LED pin information Setting of level gauge pin connection information Setting of LED pin connection information Setting of 7/14-segment LED pin connection information Setting of matrix LED pin connection information Setting of buzzer pin connection information Setting of pull-up/pull-down resistor pin connection information 114 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Window Name Object Properties Parts List dialog box Entry Bitmap dialog box Customize dialog box Edit Colors dialog box Font dialog box (Simulator Block) Open dialog box Save As dialog box Contents Setting of connection information for figure, character, and bitmap pins List display of object pin connection status in the I/O Panel window Addition of bitmap Setting of window colors and fonts Specification of colors of figures, lines, etc. (common dialog box) Selection of display text fonts (common dialog box) Specification of operation target file (common dialog box) Specification of save target file (common dialog box) User's Manual U17246EJ2V0UM 115 CHAPTER 7 WINDOW REFERENCE 7. 2 Explanation of Windows This section explains each window or dialog box as follows: Window Name / Dialog box Name Briefly explains the function of the window or dialog box and points to be noted. In addition, the display image of the window or dialog box is also illustrated. Items of related operation are also explained. Opening Explains how to open the window or dialog box. Explanation of each area Explains items to be set to or displayed in each area of the window or dialog box. Context menu Explains the context menu that is displayed in the window when the right mouse button is clicked. From the context menu, convenient functions often used in this window can be selected with a single action (window only). Function buttons Explains the operation of each button in the window or dialog box. Related operations Explains the operation of a window or dialog box related to this window or dialog box. 116 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE main window This window is automatically opened when the SM+ is started up and initialized. In SM+, other windows are manipulated from this window. (Refer to "Table 7-1 Window List".) Execution of the user program is controlled in this window. Execution of the user program is controlled in the following three modes: - Source mode (Debugs the user program at the source level.) - Instruction mode (Debugs the user program at the instruction level.) - Auto mode (Automatically selects the source mode or instruction mode.) Figure 7-1 Main Window Menu bar Tool bar Tool bar (simulator block related) Window display area Status bar - Menu bar - Menu bar (simulator block related) - Tool bar - Tool bar (simulator block related) - Window display area - Status bar User's Manual U17246EJ2V0UM 117 CHAPTER 7 WINDOW REFERENCE Menu bar (1) [File] menu (2) [Edit] menu (3) [View] menu (4) [Option] menu (5) [Run] menu (6) [Event] menu (7) [Browse] menu (8) [Jump] menu (9) [Window] menu (10) [Help] menu (1) [File] menu Open... Loads a view file, source file, or text file. Opens the View File Load dialog box. The operation differs depending on the extension of the file selected in the dialog box. Saves the contents displayed on the current window to the file whose name is specified. Opens the View File Save dialog box. Closes the current window. Downloads a file. Opens the Download dialog box. Lists the names of the files that have been downloaded. Opens the Load Module List dialog box. Uploads a program. Opens the Upload dialog box. Manipulates a project file. Opens a project file. Opens the Project File Load dialog box. Overwrites the current status to the project file currently being read to the SM+. Saves the current status to a specified project file. Opens the Project File Save dialog box. Manipulates a setting file. Opens a setting file. Opens the Environment Setting File Load dialog box. Saves the setting in the current window to the setting file. Opens the Environment Setting File Save dialog box. Initializes the CPU, symbols, and SM+. Opens the Reset Debugger dialog box. Terminate the SM+. Opens the Exit Debugger dialog box. Lists the names of the files opened. Save As... Close Download... Load Module... [V850] Upload... Project Open... Save Save As... Environment Open... Save As... Debugger Reset... Exit (Open file) 118 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (2) [Edit] menu Cut Copy Paste Write in Restore Memory Fill... Copy... Compare... Modify... Edit Source Cuts a selected character string and saves it to the clipboard buffer. Copies a selected character string and saves it to the clipboard buffer. Pastes the contents of the clipboard buffer to the text cursor position. Writes the modified contents to the target. Cancels the modification. Manipulates the memory contents. Fills the memory contents with specified codes. Opens the Memory Fill dialog box. Copies the memory. Opens the Memory Copy dialog box. Compares the memory. Opens the Memory Compare dialog box. Rewrites the memory contents during user program execution. Opens the DMM dialog box. Opens the source file displayed in the active Source window with the editor specified by the PM+ when the PM+ runs. (3) [View] menu The [View] menu contains common parts as well as dedicated parts added according to the active window. For details about the dedicated parts, refer to the description of each window. (a) Common items Search... Performs a search. Opens the search dialog box corresponding to the current window. Same operation as the Move... Quick Watch... Add Watch... View Watch Change Watch... Delete Watch Symbol... User's Manual U17246EJ2V0UM 119 CHAPTER 7 WINDOW REFERENCE (4) [Option] menu Tool Bar Status Bar Button Source Mode Instruction Mode Auto Mode Selects whether the tool bar is displayed (default) or not. Selects whether the status bar is displayed (default) or not. Selects whether the buttons on each window are displayed (default) or not. Executes step execution at the source level (in line units). Executes step execution at the instruction level (in instruction units). Automatically selects step execution at the source level or step execution at the instruction level (default). Step execution is performed at the source level (in a mode other than mixed display mode) if the Source window is active. It is performed at the instruction level if the Assemble window is active. If neither window is active, step execution is performed at the source level. Sets the environment. Opens the Configuration dialog box. Sets extended options. Opens the Extended Option dialog box. Sets SM+ options. Opens the Debugger Option dialog box. Adds user-defined I/O ports. Opens the Add I/O Port dialog box. Clears the trace data. This item is displayed only when the Trace window is active Opens the following dialog boxes related to coverage measurement. Clears the coverage measurement results. Opens the Coverage-Clear dialog box. Selects the coverage measurement range as a space of 1MB or more. Opens the Coverage-Address dialog box. Sets a coverage efficiency measurement condition. Opens the Coverage-Condition Setting dialog box. Displays coverage efficiency. Opens the Coverage-Efficiency View dialog box. Turns ON/OFF coverage measurement (default:OFF). This item cannot be selected during user program execution. Turns ON/OFF timer measurement (default:OFF). This item cannot be selected during user program execution. The timer measuring Run-Break time cannot be stopped. Turns ON/OFF the tracer (default:OFF). This item cannot be selected during user program execution. Configuration... Extended Option... Debugger Option... Add I/O Port ... Trace Clear Coverage Clear... Select... [V850] Condition... Efficiency... Coverage ON Timer ON Tracer ON 120 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (5) [Run] menu Restart Resets the CPU and executes the program. Same operation as the ReGo button. Stop Forcibly stops program execution. Same operation as the Stop button. Go Executes the program from the current PC. Same operation as the Go button. Ignore break points and Go Ignores break points being set, and executes the program. Same operation as the GoN button. Return Out The user program is executed until execution returns. Note: This command is used for a function described in C language. Same operation as the Ret button. Step In Executes the instructions in the program one by one (step execution). If a function or subroutine is called, its instructions are executed one by one. Same operation as the Step button. Next Over Executes the instructions in the program one by one (Next step execution). If a function or subroutine is called, its instructions are not executed on a stepby-step basis. Same operation as the Over button. Start From Here Come Here Go & Go Executes the program from the cursor position on the Source window or the Assemble window . Executes the program from the current PC to the cursor position in the Source window or the Assemble window. Continues executing the program. If a break occurs because a break condition is satisfied, the window is updated and the program is executed again. Same operation as clicking the Go each time a break has occurred. Slowmotion Continues step execution. Each time step execution has been performed, the window is updated and then step execution is performed again. Same operation as clicking the Step each time a break has occurred. CPU Reset Resets the CPU. Same operation as the Res button. Change PC Break Point Uncond. Trace ON Sets the address at the cursor position in the Source window or the Assemble window to the PC. Sets or deletes a breakpoint at the cursor position in the Source window or the Assemble window. Validates unconditional trace so that trace can always be executed during program execution (default). At this time, the set trace event conditions are ignored. The trace mode cannot be changed while the tracer is activated. User's Manual U17246EJ2V0UM 121 CHAPTER 7 WINDOW REFERENCE Cond. Trace ON Validates conditional trace and traces in accordance with the trace event condition during program execution. The trace mode cannot be changed while the tracer is activated. Sets trace control mode. Note In this case, select [Delay Trigger Stop] , [Delay Trigger Break]. Goes around the trace memory and overwrites data from the oldest frame (default). Goes around the trace memory and then stops the tracer. Goes around the trace memory and then stops the tracer and program execution Traces data by the number of delay count frames and stops the tracer when a delay trigger event has occurred. Traces data by the number of delay count frames and stops the tracer and program execution when a delay trigger event has occurred. Tracer Control Mode Non Stop Full Stop Full Break Delay Trigger Stop Delay Trigger Break Coverage Start/Coverage Stop Starts the coverage measurement when it is stopped, or stops it when it is in progress. This item is invalid if the program is not being executed or if the coverage function is OFF (if [Option] menu -> [Coverage ON] is not checked). Immediately after program execution has been started with the coverage function ON, coverage measurement is in progress. Starts the timer measurement when it is stopped, or stops it when it is in progress. This item is invalid if the program is not being executed, if a timer event is not used, and if the timer function is OFF (if [Option] menu -> [Timer ON] is not checked). Immediately after program execution has been started with the timer function ON, timer measurement is in progress. Starts the tracer when it is stopped, or stops it when it is in progress. This item is invalid if the program is not being executed and if the trace function is OFF (if [Option] menu -> [Tracer ON] is not checked). Immediately after program execution has been started with the tracer function ON, the tracer is executed. Timer Start/Timer Stop Tracer Start/Tracer Stop (6) [Event] menu Event Manager Manages various event conditions. Opens the Event Manager. Same operation as the Mgr button. Event... Registers an event condition. Opens the Event dialog box. Same operation as the Evn button. Event Link... Break... Registers an event link condition. Opens the Event Link dialog box. Registers and sets a break event condition. Opens the Break dialog box. Same operation as the Brk button. Trace... Registers and sets a trace event condition . Opens the Trace dialog box. Same operation as the Trc button. Snap Shot... Registers and sets a snap shot event condition. Opens the Snap Shot dialog box. 122 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Stub... Timer... Registers and sets a stub event condition. Opens the Stub dialog box. Registers and sets a timer event condition . Opens the Timer dialog box. Same operation as the Tim button. Delay Count... (7) [Browse] menu Source Text Sets a delay count . Opens the Delay Count dialog box. Displays a source text. Opens the Source window. If there is this window already open in the active status, it is opened in the static status. Same operation as the Src button. Assemble Displays the disassemble results. Opens the Assemble window. If there is this window already open in the active status, it is opened in the static status. Same operation as the Asm button. Memory Displays the contents of the memory. Opens the Memory window. If there is this window already open in the active status, it is opened in the static status. Same operation as the Mem button. Watch Displays the watch contents. Opens the Watch window. Same operation as the Wch button. Register Displays the register contents. Opens the Register window. Same operation as the Reg button. II/O Register / SFR Displays the peripheral I/O register or SFR. Opens the IOR/SFR window. Same operation as the IOR/SFR button. Local Variable Displays the local variable. Opens the Local Variable window. Same operation as the Loc button. Stack Trace Displays the stack trace results. Opens the Stack window. Same operation as the Stk button. Trace Displays the trace results. Opens the Trace window. Same operation as the TrW button. Coverage Displays the coverage results. Opens the Coverage window. Same operation as the Cov button. Console Others Opens the Console window. Displays other windows. Displays a user-defined window list. User's Manual U17246EJ2V0UM 123 CHAPTER 7 WINDOW REFERENCE (8) [Jump] menu Source Text Displays the corresponding source text and source line, using the data value selected in the current window as the jump destination address. If no line information exists at the jump destination address, however, you cannot jump. Opens the Source window. If an active Source window is open, that window is displayed in the forefront (so that it can be manipulated). Disassembles and displays the results from the jump destination address specified by the data value selected in the current window. Opens the Assemble window. If an active Assemble window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents from the jump destination address specified by the data value selected in the current window. Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Displays coverage measurement results from the jump destination address specified by the data value selected in the current window. Opens the Coverage window. If an active Coverage window is open, that window is displayed in the forefront (so that it can be manipulated). Assemble Memory Coverage (9) [Window] menu New Window Opens a new window displaying the same contents as those of the current window.This menu is valid only when the current window is the Source window, Assemble window, Memory window or Coverage window. Cascade display of the windows in the Main window. Tile display of the windows in the Main window. Rearranges the icons in the Main window. Closes all windows, except the Main window. Updates the contents of the window with the latest data. Sets the window in the active status. Sets the window in the static status. Lists the windows that are open. The window with the check mark shown on the side of the figure is the current window. By selecting a window name, the selected window is used as the current window. Cascade Tile Arrange Icons Close All Refresh Active Static (Open Window) (10) [Help] menu SM+ Help Command Reference Main Window Help Current Window Help Displays the help of SM+. Opens the Help window of COMMAND REFERENCE. Displays the help of the Main window. Displays the help of the current window. 124 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE About... Displays the version of the SM+. Opens the About dialog box. Menu bar (simulator block related) The following two types of menus are related to the simulator block. - Default menus Displayed when no simulator block window is opened in the Main window - Window-dedicated menus Displayed when a simulator block window is opened in the Main window (The displayed menu varies depending on the active window.) The default menu is displayed here. For details about the dedicated menus of the various windows, refer to the description of each window. (1) [Option] menu Displayed additionally to the debugger block menu. ToolBar Debugger Simulator Standard Simulator Tools Timing Chart Signal Data Editor Parts Figure (2) [Simulator] menu This is the original menu for the simulator block. It is used to perform manipulations related to files used in the simulator block windows, as well as to open simulator block windows. New File... Open... Close Save... Save As... Signal Data Editor Opens a new simulator block window. Opens the Open dialog box. Opens the files handled in the specified simulator block window. Closes the active simulator block window. Overwrites the contents of the currently active simulator block window to the file handled in the currently opened simulator block window, and then saves this file. Opens the Save As dialog box. Saves the contents of the currently active simulator block window to the specified file. Opens the Signal Data Editor window. Switches on/off display of the tool bar corresponding to the cascade menu. Switches on/off display of Tool bar. Switches on/off display of (1) [Standard] tool bar. Switches on/off display of (2) [Tool] tool bar. Switches on/off display of (3) [Timing Chart] tool bar. Switches on/off display of (4) [Signal Data Editor] tool bar. Switches on/off display of (5) [Parts] tool bar. Switches on/off display of (6) [Figure] tool bar. User's Manual U17246EJ2V0UM 125 CHAPTER 7 WINDOW REFERENCE Timing Chart Standard I/O Serial I/O Panel Opens the Timing Chart window. Opens the Standard I/O window. Opens the Serial window. Opens the I/O Panel window. Tool bar (1) Meaning of each button (2) Operation of tool bar (1) Meaning of each button The meaning of each button on the tool bar is as follows. When the mouse cursor is placed on a button of the tool bar, a tool hint pops up several seconds later. Stops execution of the user program. Same function as [Run] menu -> [Stop] . Resets the CPU and executes the user program. Same function as [Run] menu - > [Restart] . Executes the user program from the current PC without resetting the CPU. Same function as [Run] menu -> [Go] . Ignores break points being set, and executes the user program. Same function as [Run] menu -> [Ignore break points and Go] . The user program is executed until execution returns Same function as [Run] menu -> [Return Out] . Note : This command is used for a function described in C language. Step execution (executes instructions in the program one by one.) If a function or subroutine is called, its instructions are executed one by one. Same function as [Run] menu -> [Step In] . Next step execution (executes the program, assuming a function/call statement as one step.) If a function or subroutine is called, its instructions are not executed on a step-by-step basis. Same function as [Run] menu -> [Next Over] . Resets the CPU. Res Opens the View File Load dialog box. Same function as [File] menu -> [Open...]. Open Opens the Download dialog box. Same function as [File] menu -> [Download...]. Load Opens the Project File Load dialog box. Same function as [File] menu -> [Project] -> [Open...]. Displays the source text. Opens the Source window. Same function as [Browse] menu -> [Source Text] . Displays the disassemble results. Opens the Assemble window. Same function as [Browse] menu -> [Assemble] . Same function as [Run] menu -> [CPU Reset]. Stop ReGo Go GoN Ret Step Over Proj Src Asm 126 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Mem Displays the contents of the memory. Opens the Memory window. Same function as [Browse] menu -> [Memory] . Displays the watch contents. Opens the Watch window. Same function as [Browse] menu -> [Watch] . Displays the register contents. Opens the Register window. Same function as [Browse] menu -> [Register] . Displays the contents of peripheral I/O register or SFR. Opens the IOR/SFR window. Same function as [Browse] menu -> [I/O Register/SFR] . Displays the local variable contents. Opens the Local Variable window. Same function as [Browse] menu -> [Local Variable] . Displays the current stack contents. Opens the Stack window. Same function as [Browse] menu -> [Stack Trace] . Displays the trace results . Opens the Trace window. Same function as [Browse] menu -> [Trace] . Displays the coverage results. Opens the Coverage window. Same function as [Browse] menu -> [Coverage] . Opens the Event Manager. Same function as [Event] menu -> [Event Manager...]. Registers and sets events. Opens the Event dialog box. Same function as [Event] menu -> [Event...]. Registers and sets break events. Opens the Break dialog box. Same function as [Event] menu -> [Break...]. Registers and sets a trace event. . Opens the Trace dialog box. Same function as [Event] menu -> [Trace...]. Registers and sets a timer event. Opens the Timer dialog box. Same function as [Event] menu -> [Timer...]. Wch Reg IOR/SFR Loc Stk TrW Cov Mgr Evn Brk Trc Tim (2) Operation of tool bar Whether the tool bar is displayed or not can be specified by selecting [Option] menu -> [Tool Bar]. This tool bar can be displayed in the following two modes. The modes are selected in the Debugger Option dialog box. Figure 7-2 Tool Bar (Picture Only) Figure 7-3 Tool Bar (Picture and Text) User's Manual U17246EJ2V0UM 127 CHAPTER 7 WINDOW REFERENCE Tool bar (simulator block related) The simulator block's dedicated toolbar features a group of 2 common toolbars and a group of 4 dedicated toolbars as shown below, and show/hide can be switched independently for each of these two groups by selecting [Option] menu -> [ToolBar]. Figure 7-4 Tool Bar (Simulator Block) Standard Tool Timing Chart Signal Data Editor Parts Figure Common tool bar (1) [Standard] tool bar (2) [Tool] tool bar Dedicated tool bar (3) [Timing Chart] tool bar (4) [Signal Data Editor] tool bar (5) [Parts] tool bar (6) [Figure] tool bar (1) [Standard] tool bar This menu can be used in simulator block windows in common. Selectable at all times. Opens a new simulator block window. Opens the Open dialog box. Opens the files handled in the specified simulator block window. Overwrites the contents of the currently active simulator block window to the file handled in the currently opened simulator block window, and then saves this file. Undoes the immediately preceding operation. Restores the status undone by the [Undo] command. Cuts the selected range and saves it to the clipboard. Copies the selected range and saves it to the clipboard. Pastes the clipboard contents. Performs the same operation as when the search menu is selected in the active window. Displays the contents of the Help window. 128 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (2) [Tool] tool bar This menu is used to create a new simulator block window. Selectable at all times. Opens the Signal Data Editor window. Opens the Timing Chart window. Opens the Standard I/O window. Opens the Serial window. Opens the I/O Panel window. (3) [Timing Chart] tool bar This menu can be selected if the Timing Chart window is active. (Refer to [Timing Chart] tool bar.) (4) [Signal Data Editor] tool bar This menu can be selected if the Signal Data Editor window is active. (Refer to [Signal Data Editor] tool bar.) (5) [Parts] tool bar This menu can be selected if the I/O Panel window is active. (Refer to [Parts] menu / Tool bar (Parts).) (6) [Figure] tool bar This menu can be selected if the I/O Panel window is active. (Refer to [Figure] menu / Tool bar (Figure).) Window display area This area displays various debug windows. The displayed window can be changed in size or an icon can be created in this area. Status bar The status bar displays the status of the SM+. While the user program is being executed, the status bar is displayed in red. Whether the status bar is displayed or not can be specified by selecting [Option] menu -> [Status Bar]. Figure 7-5 Status Bar (1) Program name Source name Line number (2) Function name (3) PC value Displays the program file name indicated by the PC value. Displays the source file name indicated by the PC value. Displays the line number indicated by the PC value. Displays the function name indicated by the PC value. Displays the current PC value. User's Manual U17246EJ2V0UM 129 CHAPTER 7 WINDOW REFERENCE (4) CPU status (5) IE status (6) Break Cause (7) STEP mode Refer to "Table 7-2 CPU Status". Refer to "Table 7-3 IE Status". (If there are two or more the statuses, they delimited with '|' and displayed.) Refer to "Table 7-4 Break Cause". Displays the step execution mode. Displays that the following modes are selected from the [Option] menu: SRC .............. Source mode INST ............. Instruction mode AUTO............ Automatic mode Displays the key input mode. INS................ Insertion mode OVR .............. Overwrite mode The Memory window is fixed to OVR mode. Table 7-2 CPU Status (8) Key input mode Display STANDBY HALT [78K0S] STOP [78K0S] RESET Standby mode Halt mode Stop mode Reset mode Meaning Table 7-3 IE Status Display RUN STEP TRC TIM COV BREAK Meaning User program execution in progress (the color of the status bar changes) Step execution in progress Tracer operating Timer operating Coverage operationg Break occurring Table 7-4 Break Cause Display Manual Break Temporary Break Event Break Trace Full Break Non Map Break Write Protect Forced break Temporary break Break by event Break due to trace full Non-mapped area is accessed An attempt has been made to write to a write-protected area Meaning 130 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Display SFR Illegal [78K] IOR Illegal (xxx) [V850] Stack Overflow [78K] Uninitialize Memory Read [78K] Security Protect SFR was illegally accessed Meaning Illegal access to peripheral I/O register was performed. (xxx indicates the corresponding address.) Break due to stack overflow Break due to failure to read uninitialized memory A security protected area is accessed User's Manual U17246EJ2V0UM 131 CHAPTER 7 WINDOW REFERENCE Configuration dialog box This dialog box is used to display and set the SM+ operation environment. (Refer to "5. 1 Setting Debugging Environment".) This dialog box is automatically displayed after the SM+ is started up. However, no setting is required to read a project as the results of reading the project file are reflected in this dialog box. (Refer to "5. 16. 1 Debugging environment (project file)".) Figure 7-6 Configuration Dialog Box - Opening - Explanation of each area - Function buttons Opening (Automatically when the SM+ is started up) Select [Option] -> [Configuration...] from the menu bar. Explanation of each area (1) Chip (2) Internal ROM/RAM (3) Oscillation Frequency (4) Programmable I/O Area [V850] (5) Simulator Configuration (6) Memory Mapping 132 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Chip This area is used to select the chip name. A chip name is selected from the drop-down list. On the drop-down list, only the chip names registered to the registry from the device file installer are displayed. This area can be specified only when the debugger is started up. Remark By default, the type selected at the previous startup is displayed, but if that type is not registered, the first type registered is displayed. (2) Internal ROM/RAM This area is used to set the size of the internal RAM and internal ROM of the CPU. A mapping size is selected from the drop-down list. The default size is obtained from the device file through selection in (1) Chip , and displayed (value with '*'). Table 7-5 Range and Unit of Internal ROM/RAM Setting Area Internal ROM Device [V850] [78K] Internal RAM [V850] [78K] Settable range 0,32,64,128,256,512,1024 bytes 1024,2048,3072,4096,6144,8192,10240,12288,16384,20480,24576, 28672,36864,45056,53248,61440 bytes (3) Oscillation Frequency This area is used to select the oscillation frequency to be input to the oscillator. Main (MHz) Sub (KHz) Specifies the frequency to be input to the main clock oscillator Equivalent to the setting of the external frequency pin for the main clock (X1 pin, etc.) Specifies the frequency to be input to the sub clock oscillator Equivalent to the setting of the external frequency pin for the sub-clock (TX1 pin, etc.) (4) Programmable I/O Area [V850] This area is used to specify usage of the programmable I/O area and the start address. The start address of the programmable I/O area can be specified, only if the device selected by (1) Chip supports the programmable I/O area. The start address of the programmable I/O area can be input by checking the check box when the programmable I/O area is used. The address is aligned to 16 KB. Caution Remark To use a programmable I/O area or extended I/O area, mapping that area as a target is required. IIn the case of a device with an extended I/O area with fixed addresses, the device selected by (1) Chip , Setting of this area is performed automatically. If the selected device has an extended I/O area whose address is fixed, the address setting and the check are executed automatically. User's Manual U17246EJ2V0UM 64 0 60 bytes (in 1K byte units) 1024 bytes (in 16 byte units) 133 CHAPTER 7 WINDOW REFERENCE (5) Simulator Configuration This area is used to specify the configuration file used to perform user customization (addition of user models) of the simulator. When reading a configuration file other than the default file, check this check box and specify the file name. When this check box is not checked, the default configuration file will be read. (6) Memory Mapping This area is used to set mapping by specifying the memory access size, attribute and address. (a) Access Size Selects memory access size. Fixed to 8-bit. (b) Memory Attribute The following mapping attributes can be selected. Select a mapping attribute according to the usage. (Refer to "5. 1. 3 Setting mapping".) Table 7-6 Type of Mapping Attribute Mapping Attribute Emulation ROM [V850] [78K0] Emulation RAM [V850] [78K0] Target [V850] [78K0] I/O Protect [V850] [78K0] Meaning Selects the simulator alternate ROM.Note1 Selects the simulator alternate RAM.Note1 Selects the target memory.Note1 Selects the I/O protect area. This area can be set in the area specified as Target and in the external SFR area [78K0] The I/O protect area is displayed in the same manner as an area that is not mapped (display symbol: ??), on the Memory window. By mapping an area with this attribute, data cannot be read or written from/to this area by the Memory window, on the area can therefore be protected from an illegal access.Note2 The mapping unit is 1 byte. Selects the memory of the stack area. The stack area can be set in the internal high-speed RAM area. The mapping unit is 1 byte. Stack [78K] Note 1 Note 2 The mapping unit is 1 MB [V850] /8 KB [78K0] (the mappable area depends on the product type). The area set as I/O Protect is not read unless it is registered to the IOR/SFR window or Watch window as an I/O port. To read this area, forcibly read it on these windows. 134 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (c) Mapping Address Specify the address to be mapped. Input the higher and lower addresses from the keyboard. (d) Function buttons OK Validates the current environment. Sets the environment and closes this dialog box. If an error occurs after clicking the Cancel Restore Project... About... Help User's Manual U17246EJ2V0UM 135 CHAPTER 7 WINDOW REFERENCE Extended Option dialog box This dialog box is used to display and set the extended options of the SM+. (Refer to "5. 1 Setting Debugging Environment".) Figure 7-7 Extended Option Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Option ] menu -> [Extended Option ...] . Explanation of each area (1) Trace Size (2) Trace Timetag Count Rate (3) Add Up Timetag (4) Internal RAM Monitor Redraw (5) Break Condition (6) Break Sound (7) Verify (8) Project Save Level [V850] 136 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Trace Size This area is used to set the size (frame units) in which execution of the user program is to be traced. The following sizes can be set: 4K 64K 1M 0 to 64K 64K to 1M 1M to 16M (2) Trace Timetag Count Rate This area is used to set the division ratio of the counter used for time tag display in the Trace window. If the division ratio is set, the number of clocks necessary for counting up the counter displayed for time tag is changed. (3) Add Up Timetag This area is used to specify whether time tags of trace data are totaled or not. This check box is not checked by default, and the time tags are not totaled. (4) Internal RAM Monitor Redraw Specify the sampling time (ms) of the RRM function (refer to "5. 15 RAM Sampling Function"). The sampling time can be specified in 100-ms units from 0 to 65500. If 0 is specified, or if this area is blank, the data is not displayed in real time. (5) Break Condition This area is used to select whether a break occurs before or after the instruction of a breakpoint is executed. This setting affects only hardware breaks. Before After Sets a Run event as an event before executing (default). The event occurs before the instruction is executed. Sets a Run event as an event after executing. The event occurs after the instruction is executed. (6) Break Sound If the check box is checked, a beep sound is issued when a break occurs. (7) Verify This area is used to specify whether a verify check is performed when data has been written to memory. A verify check is performed when download, memory fill, or memory copy is executed. A verify check is also performed when a variable or data is changed in the Watch window or the Memory window and is written to memory. User's Manual U17246EJ2V0UM 137 CHAPTER 7 WINDOW REFERENCE (8) Project Save Level [V850] This area is used to select the save level of a project file related to the simulator. Basic Normal Saves only the user-set debug environment (such as window status and event setting status) (default). Saves the contents of Basic and the status of the internal instructions of the simulator (project information such as instructions, memory, registers, and peripheral I/O registers), which are stopped. Saves contents of Normal and all debug information generated during simulation (such as trace and coverage results). Full Function buttons OK Cancel Restore Help Validates the settings and closes this dialog box. Cancels the changes and closes this dialog box. Restores the previous settings before this dialog box was opened. Displays the help window of this window. 138 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Debugger Option dialog box This dialog box is used to display and set the various options of the SM+. Figure 7-8 Debugger Option Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Option] menu -> [Debugger Option...]. Explanation of each area (1) Source Path (2) Default Extension (3) Open File History (4) Font (5) Project File (6) Tool Bar Pictures (7) Kanji (8) Tab Size (9) Startup Routine (10) DisAssemble (11) Watch Default User's Manual U17246EJ2V0UM 139 CHAPTER 7 WINDOW REFERENCE (1) Source Path This area is used to specify the directory in which a source file or text file is searched. (a) Base: The directory is the basis of a relative path is displayed. The base directory is determined in the following sequence: 1) 2) 3) Directory to which the project file has been loaded Directory to which a load module or hex file has been loaded last Current directory of Windows (b) Text box This area is used to specify the directory searched. To specify a directory, either directly input one to the text box, or click the 140 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (2) Default Extension This area is used to specify the default extension. Delimit extensions with " " (blank),";" (semicolon) or "," (comma). Source File: Set the extension of a source file that is displayed when the Browse dialog box is opened by selecting [File] menu -> [Open...]. The default extension is " *.c, *.s , *.asm [78K] ". Set the extension of a load module that is displayed when the Download dialog box is opened. The default extension is " *.out [V850] *.lnk [78K] , *.lmf [78K] ". Load Module: (3) Open File History This area is used to set the number of histories of the open file displayed in the bottom field of the [File] menu. The default value is 4. If 0 is set, no history is displayed on the menu. (4) Font This area is used to specify the font displayed on the Source window, Watch window, Quick Watch dialog box, Local Variable window, and the Stack window. Clicking the (b) Auto Load: Sets whether the project file is automatically loaded at the SM+ start up. On Off Automatically loads the project file at the SM+ start up. Specify the project file to be loaded in (c) Load Project File. Does not automatically loads the project file at the ID850QB start up. (default) Load Project File (c) Specify the project file to be loaded automatically. Set a project file name by inputting from the keyboard or clicking the User's Manual U17246EJ2V0UM 141 CHAPTER 7 WINDOW REFERENCE (6) Tool Bar Pictures This area sets the buttons to be displayed on the tool bar. (Refer to " Tool bar".) Pictures and Text Pictures only Displays a button on which a graphic and character are displayed. Displays a button with only graphic (default). (7) Kanji Cannot be selected. (8) Tab Size This area is used to set the tab size for each extension when files are displayed. (a) Extension: Set an extension. Input an extension from the keyboard, or select one from the drop-down list. (b) Tab Size: Select the tab size. Select how many spaces are displayed as a tab code (2, 4, or 8) . (c) Tab List: Displays the tab size set for each extension. (d) Caution1 If the specified symbol is not correct, the source file cannot be opened until the PC reaches the address range of the corresponding source file. In addition, the start-up routine cannot be skipped by step execution. Caution2 Be sure to specify this area. If this area is blank, the dialog box cannot be closed. 142 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (10) DisAssemble This area is used to set for disassemble display. (a) Show Offset: Specifies whether an offset (symbol + offset) is displayed during disassemble display. When the offset is not displayed, only a symbol that matches a numeric value is displayed, if any. If no matching symbol is found, the numeric value is displayed as a hexadecimal number unchanged. Label Mnemonic Specifies whether the offset is displayed in the Label field. In the default condition, the offset is not displayed. Specifies whether the offset is displayed in the Mnemonic field. In the default condition, the offset is displayed. (b) Register Name: This area is used to select the method of displaying register names in mnemonics during disassemble display. Function Name Absolute Name Displays register names as function names or nicknames (default). Displays register names as absolute names. (11) Watch Default This area is used to specify a symbol to be watched in the Watch window etc. . (a) Size: Sets the default display size of data if [Adaptive] is specified. Byte Half Word [V850] Word Double Word [78K] 8-bit display (default) 16-bit display 16-bit display [78K] 32-bit display [V850] 32-bit display (b) Radix: Sets the default radix in which data is to be displayed if [Proper] is specified. Hex Dec Oct Bin String Displays data in hexadecimal numbers (default). Displays data in decimal numbers. Displays data in octal numbers. Displays data in binary numbers. Displays data in character strings. User's Manual U17246EJ2V0UM 143 CHAPTER 7 WINDOW REFERENCE (c) Show Variable Type: Select the display/non-display of variable type is specified. On Off Displays the type of a variable. Does not display the type of a variable (default). (d) Language: Select the display/non-display of type of variable is specified. C ASM Displays a C-like base number (default). Cannot be selected. [V850] Displays an assembly language-like base number. [78K] Function buttons OK Cancel Restore Help Validates the settings and closes this dialog box. Cancels the changings and closes this dialog box. Restores the previous settings before this dialog box was opened. Displays this dialog box online help files. 144 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Project File Save dialog box This dialog box is used to save the current debugging environment to a project file. Debugging environment (project file)".) Project files can be newly saved or saved under an existing file name in this dialog box. Figure 7-10 Project File Save Dialog Box (Refer to "5. 16. 1 - Opening - Explanation of each area - Function buttons Opening Select [File] menu -> [Project] -> [Save As...]. (To save a file of same name as a project file previously loaded or saved, select [File] menu -> [Project] -> [Save].) Explanation of each area (1) Save in:, File name: (2) Save as type: (3) Save Level [V850] User's Manual U17246EJ2V0UM 145 CHAPTER 7 WINDOW REFERENCE (1) Save in:, File name: This area is used to specify a file name. A file name can be directly input, or selected from the list at the upper part of this area. Up to 257 characters string with a extension can be specified. (2) Save as type: This area is used to specify the extension (*.prj) of the project file to be saved. If the extension is omitted, "*.prj" is appended as the default extension. (3) Save Level [V850] This area is used to select the save level for project files. It is similar to the setting of the Extended Option dialog box. Refer to (8) Project Save Level [V850]. When the save level is changed, this change is reflected to the Extended Option dialog box. Function buttons Save Cancel Help Saves the debugging environment to the selected file. After saving, the dialog box is closed. Closes this dialog box without saving the file. Displays this dialog box online help files. 146 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Project File Load dialog box This dialog box is used to restore the debugging environment to the debugging environment saved to the project file. (Refer to "5. 16. 1 Debugging environment (project file)") If there is an active Source window after a project file has been loaded, it is displayed at the top. Caution Following SM+ startup, if a project file with settings that differ from those of the target device at startup has been loaded, the target device specified at startup is used. Figure 7-11 Project File Load Dialog Box - Opening - Explanation of each area - Function buttons Opening Click the Proj button, select [File] menu -> [Project] -> [Open...]. Explanation of each area (1) Look In:, File name : (2) Files of type : User's Manual U17246EJ2V0UM 147 CHAPTER 7 WINDOW REFERENCE (1) Look In:, File name : This area is used to specify the file name to be loaded. A file name can be directly input from the keyboard, or selected from the list. Up to 257 characters string with a extension can be specified. (2) Files of type : This area is used to specify the extension (*.prj) of the file to be loaded. Function buttons Open Cancel Help Loads the selected file. After loading the file, this dialog box is closed. Closes this dialog box without executing anything. Displays this dialog box online help files. 148 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Download dialog box This dialog box is used to select the name and format of a file to be downloaded, and downloads memory contents to the simulator and the target system. (Refer to "5. 2 Download Function, Upload Function"). If a load module file has been downloaded, the corresponding source file is searched, and the Source window is automatically opened. Caution If a file other than a load module file is loaded, source debugging cannot be executed. Figure 7-12 Download Dialog Box Remark The following dialog box appears while downloading and the downloading can be can celled at any time. This dialog box is closed automatically after completing downloading. Figure 7-13 The Progress of Download - Opening - Explanation of each area - Function buttons User's Manual U17246EJ2V0UM 149 CHAPTER 7 WINDOW REFERENCE Opening Click the Load button, or select [File] menu -> [Download...]. Explanation of each area (1) Look In:, File name: (2) Files of type: (3) Load (4) Reset (5) Offset Address (1) Look In:, File name: This area is used to specify a file name. A file name can be directly input from the keyboard, or selected from the list at the upper part of this area. Up to 257 characters string with a extension can be specified. Remark Two or more files can be specified in this dialog box. To specify two or more files, delimit each file name with " " (double quotation mark). while holding down the Shift or Ctrl key. Up to 20 load module files can be downloaded. [V850] (2) Files of type: This area is used to specify the type (extension) of the file to be downloaded. (Refer to "Table 5-2 Type of File That Can Be Downloaded".) Remark These are default extensions; other extensions can also be used. The default extension of the displayed load module can also be specified in the Debugger Option dialog box. (3) Load This area is used to set a load condition. This setting is valid only if a file in the load module format is specified. This setting is valid only if a file in the load module format is specified. Symbol Object Specifies whether symbol information is read or not. Specifies whether object information is read (when checked, default) or not. (The object information is read even if this button is not checked when a HEX file is loaded.) Files can also be specified by clicking the mouse button 150 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Remark Specifies whether symbol information is read (when checked, default) or not. The memory capacity can be saved by not reading symbol information when a program consisting of two or more load module files is to be debugged and if the symbol information of some modules does not have to be read. [V850] (4) Reset This area is used to set a reset condition. This setting is valid only if a file in the load module format is specified. Symbol Specifies whether symbol information is reset or not. [V850] Note Fixed to checked status (always reset). [78K] Specifies whether the CPU is reset or not. (Not reset in default. [V850] Reset in default. [78K] ) CPU Note When debugging a program consisting of two or more load module files, load each one of the load module files without resetting the symbol information. When downloading two or more load module files, take care that location addresses do not overlap. [V850] (5) Offset Address This area is used to specify the offset address that is used when a file is loaded (for binary data, specify the start address). An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols"".). The default radix for inputting a numeric value is hexadecimal. Function buttons Open Cancel Help Restore Loads the selected file. After loading the file, this dialog box is closed. Closes this dialog box without loading the file. Displays this dialog box online help files. Restores the input data to the original status. User's Manual U17246EJ2V0UM 151 CHAPTER 7 WINDOW REFERENCE Upload dialog box This dialog box is used to set the name and format of the file to be saved, and save the set memory contents, etc., to that file. (Refer to "5. 2 Download Function, Upload Function") Figure 7-14 Upload Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [File] menu -> [Upload...]. Explanation of each area (1) Save in :, File name : (2) Save as Type : (3) Save Address 152 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Save in :, File name : This area is used to specify the file name to be saved. A file name can be directly input from the keyboard, or selected from the list. Up to 257 character string with a extension can be specified. (2) Save as Type : This area is used to specify the type (extension) of the file to be saved. The format of the data to be saved is determined by the extension. (Refer to "Table 5-3 Type of File That Can Be Uploaded") However, if "All (*.*) " is selected, the data is saved in the default Intel extended Hex format. Remark Extensions other than those listed can also be used. (3) Save Address This area is used to specify the range of address to be saved. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) The default radix for inputting a numeric value is hexadecimal. Function buttons Save Cancel Help Restore Saves the file according to the setting. Closes this dialog box without executing anything. Displays this dialog box online help files. Restores the status before this dialog box was opened. User's Manual U17246EJ2V0UM 153 CHAPTER 7 WINDOW REFERENCE Load Module List dialog box [V850] This dialog box can be used to check the file name and file path name of a load module that has already been downloaded. (Refer to "5. 2 Download Function, Upload Function".) By using the - Opening - Explanation of each area - Function buttons Opening Select [File] menu -> [Load Module...]. Explanation of each area (1) Module list (2) Add Path 154 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Module list This area displays the names of the load module files that have already been downloaded. (a) No. The numbers displayed indicate the sequence in which the load module file names were read. (b) File name The file names are displayed with the full path if (2) Add Path is checked; otherwise, only the file names will be displayed. Caution If symbol information has been reset in the Reset Debugger dialog box, or if symbol information has been reset in the Download dialog box, the load module file names downloaded before that are cleared. (2) Add Path This should be checked to specify load module file names are displayed with the path in (1) Module list. Function buttons Close Help Download... Closes this dialog box. Displays this dialog box online help files. Opens the Download dialog box. A new load module can be downloaded. The file name of the newly downloaded module will be added to the file name display area when the Download dialog box is closed. User's Manual U17246EJ2V0UM 155 CHAPTER 7 WINDOW REFERENCE Source window This dialog box is used to displays source files or text files. (Refer to "5. 3 Source Display, Disassemble Display Function".) In addition to Breakpoint setting and Mixed display mode (Source window), a number of other operations using Context menu, Function buttons, etc., can be performed in this window. Moreover, there are two statuses, Active status and static status, for this window. When the window is in the active status, it has the Trace result with linking window. Moreover, the items selected in the window with Drag & drop function can be used in another window. (Refer to "5. 17 Functions Common to Each Window".) Caution If program codes is described in an include file and these codes are included in multiple files, the line numbers and addresses do not correspond on a one-to-one bases. In such an include file, function that indicates the correspondence relationship between line numbers and addresses dose not correctly operate. Figure 7-16 Source Window - Opening - Explanation of each area - [View] menu (Source window-dedicated items) - Context menu - Function buttons 156 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Opening Click the Src button, select [Browse] menu -> [Source Text]. (This window is automatically opened if the corresponding source file exists after the download module file has been downloaded. ) Explanation of each area (1) Point mark area (2) Current PC mark area (3) Line number/address display area (4) Source text display area (1) Point mark area This area is used for the Event Setting Status (Event Mark) and program codes (*) display, as well as Breakpoint setting. Caution The program code is displayed only when the symbol information downloaded by the load module is read. Breakpoints can be set or deleted by clicking with the mouse on this program code. (if "*" is not displayed for the line, the breakpoint is set on the line above or below the line, whichever has "*" displayed). If an event has been set for the corresponding line, one of the marks listed in the following table is displayed. The color of the "B" mark differs according to the breakpoint type and status. (When a breakpoint is set in this area, it is enabled at the same time that it is set.) Table 7-7 Event Setting Status (Event Mark) Mark B (red) B (black) Valid hardware breakpoint is set. Invalid hardware breakpoint is set. This hardware breakpoint can be validated on the Event Manager or in the Break dialog box. Event condition is set. Event link condition is set. Trace event is set. Timer event is set. Snapshot event is set. Stub event is set. Multiple events are set. Meaning E L T Ti S U A User's Manual U17246EJ2V0UM 157 CHAPTER 7 WINDOW REFERENCE Remark If an address range is specified as the address condition of the event, the lower addresses of the range are displayed. The mask specification of the address condition is not reflected. (2) Current PC mark area The mark '>', which indicates the current PC value (PC register value), is displayed in this area. Clicking this mark with the mouse displays a pop-up window that shows the PC register value. By double-clicking the current PC mark area, the program can be executed up to a specified line. (3) Line number/address display area This area displays the line numbers of a source file or text file. Red indicates line numbers for which corresponding program code exists, and black indicates line numbers for which corresponding program code does not exist. In the Mixed display mode (Source window), disassemble display addresses are displayed in gray. (4) Source text display area This area displays source files and text files. Yellow indicates the current PC line, and red indicates lines where a valid breakpoint is set. In the Mixed display mode (Source window), source lines are displayed in the regular color. Moreover, this area also provides the following functions for lines (start address of program code) and addresses where the cursor has been placed. - [Come Here] , [Start From Here] (Refer to "Table 5-7 Type of Execution") - Drag & drop function - Context menu Caution If a Program code does not exist on the source line, the top address of the line above or below the line on which a program code exists is manipulated by these functions. . These functions cannot be performed in the following cases. The corresponding menu will be dimmed and cannot be selected. - If a file other than a source file is displayed - While the user program is being executed 158 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE [View] menu (Source window-dedicated items) The following items are added in the [View] menu, when the Source window is active. Create Break Event Break when Access to this Variable Break when Write to this Variable Break when Read from this Variable Clear Event? Mix Sets a break event that occurs if the selected variable is accessed. Sets a break event that occurs if the selected variable is accessed for read/ write. Sets a break event that occurs if the selected variable is accessed for write. Sets a break event that occurs if the selected variable is accessed for read. Deletes a break event corresponding to the selected variable. Displays the event information of a line at the cursor position or a selected variable name. If an event is set, the Event dialog box is opened. Turns on/off Mixed display mode (Source window). Context menu Move... Mix Add Watch... Symbol... Moves the display position. Opens the Source Text move dialog box. Turns on/off Mixed display mode (Source window). Adds the specified data to the Watch window. Opens the Add Watch dialog box. Displays the address of the specified variable or function, or the value of the specified symbol. Opens the Symbol To Address dialog box. Sets a break event that occurs if the selected variable is accessed for read/ write. Sets a break event that occurs if the selected variable is accessed for write. Sets a break event that occurs if the selected variable is accessed for read. Deletes a break event corresponding to the selected variable. Displays the event information of a line at the cursor position or a selected variable name. If an event is set, the Event dialog box is opened. Executes the program from the current PC to the cursor position. (Refer to "Table 5-6 Break Types".) Sets the address at the cursor position to the PC. Sets or deletes a breakpoint at the cursor position. Break when Access to this Variable Break when Write to this Variable Break when Read from this Variable Clear Event? Come Here Change PC Break Point User's Manual U17246EJ2V0UM 159 CHAPTER 7 WINDOW REFERENCE Assemble Disassembles and displays starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Assemble window. If an active Assemble window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Coverage window. If an active Coverage window is open, that window is displayed in the forefront (so that it can be manipulated). Memory Coverage Function buttons Search... Opens the Source Search dialog box and searches a character string of the source text. If a character string is selected in the source text display area, the Source Search dialog box is opened to search the character string. If no character string is selected, the Source Search dialog box is opened with nothing specified to be searched. Specify a search method in the Source Search dialog box. The results of search is highlighted in the Source window. This is the same operation as selecting [View] menu -> [Search...]. Searches forward (upward on screen) for the text that satisfies the search condition set in the Source Search dialog box, starting from the address at the cursor position. This button is displayed as the << >> Stop(during a search) Watch Quick... Refresh Close 160 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Source Search dialog box This dialog box is used to search the contents of a file in the Source window. (Refer to "5. 3. 1 Source display".) By setting each item and then clicking the - Opening - Explanation of each area - Function buttons Opening When the Source window is the current window, select [View] menu -> [Search...], or click the Explanation of each area (1) Find What (2) Match Case (3) Direction User's Manual U17246EJ2V0UM 161 CHAPTER 7 WINDOW REFERENCE (1) Find What This area is used to specify the data to be searched. (Up to 256 character.) In the default condition, the string selected in the window that called this dialog box is displayed. As necessary, the character string displayed can be changed. Up to 16 input histories can be recorded. (2) Match Case This should be checked to distinguish between uppercase and lowercase. (3) Direction This area is used to specify the direction of the search. Up Down Forward search. Searches data forward (upward on screen) from the current position of the cursor. Backward search. Searches data backward (downward on screen) from the current position of the cursor (default). Function buttons Find Next Searches the specified data in accordance with a given condition. If the specified character string is found as a result of a search, it is highlighted. To continue searching, click this button again. Sets the specified condition as the search condition and closes this dialog box. Stops searching. Closes this dialog box. (During searching, this button is replaced by the Set Find Stop (during searching) Cancel Help 162 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Source Text move dialog box This dialog box is used to specify a file to be displayed in the Source window and the position from which displaying the file is to be started. (Refer to "5. 3. 1 Source display".) Figure 7-18 Source Text Move Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Source window is the current window, select [View] menu -> [Move...]. Explanation of each area (1) Option (2) To: User's Manual U17246EJ2V0UM 163 CHAPTER 7 WINDOW REFERENCE (1) Option This area is used to select the input mode when the display start position is specified. (a) Address/Symbol This should be selected to specify by an address (or symbol). (b) Line/File This should be selected to specify by a line number (or file name). Function buttons OK Cancel Restore Help Starts displaying the source text from the specified position. Closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. 164 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Assemble window This window is used to disassemble and display programs. It is also used to execute Online assembly. (Refer to "5. 3 Source Display, Disassemble Display Function".) The results of online assembly are also reflected in the Memory window. In addition to Breakpoint setting , a number of other operations using Context menu, Function buttons, etc., can be performed in this window. Moreover, there are two statuses, Active status and static status, for this window. When the window is in the active status, it has the Trace result with linking window. Moreover, the items selected in the window with the Drag & drop function can be used in another window. (Refer to "5. 17 Functions Common to Each Window".) Figure 7-19 Assemble Window - Opening - Explanation of each area - [View] menu (Assemble window-dedicated items) - Context menu - Function buttons - Related operations Opening Click the Asm button, select [Browse] menu -> [Assemble] . User's Manual U17246EJ2V0UM 165 CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Point mark area (2) Current PC mark area (3) Address specification area (4) Disassemble display area (1) Point mark area This area is used for Event Setting Status (Event Mark) and Breakpoint setting. (2) Current PC mark area The mark '>', which indicates the current PC value (PC register value), is displayed in this area. By double-clicking the current PC mark area, the program can be executed up to a specified line. (3) Address specification area This area displays the disassembly start address. (4) Disassemble display area This area displays the labels and code data of addresses, and disassembled mnemonics. This area displays source files and text files. Yellow indicates the current PC line, and red indicates lines where a valid breakpoint is set. It can be Online assembly in the mnemonic field. This area also provides the following functions: - [Come Here] , [Start From Here] (Refer to "Table 5-7 Type of Execution") - Drag & drop function - Context menu [View] menu (Assemble window-dedicated items) The following items are added in the [View] menu, when the Assemble window is active. Event? Displays the event information of the address at the cursor position. If an event is set, the Event dialog box is opened. Context menu Move... Add Watch... Symbol... Moves the display position. Opens the Address move dialog box. Adds the specified data to the Watch window. Opens the Add Watch dialog box. Displays the address of the specified variable or function, or the value of the specified symbol. Opens the Symbol To Address dialog box. Executes the program from the current PC to the cursor position. (Refer to "Table 5-6 Break Types".) Come Here 166 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Change PC Break Point Source Text Sets the address at the cursor position to the PC. Sets or deletes a breakpoint at the cursor position. Displays the corresponding source text and source line, using the data value at the cursor position as the jump destination address. (Refer to "5. 17. 2 Jump function".) If no line information exists at the jump destination address, however, you cannot jump. Opens the Source window. If an active Source window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Coverage window. If an active Coverage window is open, that window is displayed in the forefront (so that it can be manipulated). Memory Coverage Function buttons Search... Opens the Assemble Search dialog box and searches for a character string of mnemonics. Specify a search method in the Assemble Search dialog box. The results of search is highlighted in the Assemble window. This is the same operation as selecting [View] menu -> [Search...]. Searches forward (upward on screen) for the contents that satisfy the search condition set in the Assemble Search dialog box, starting from the address at the cursor position. This button is displayed as the << >> Stop(during a search) Watch Quick... Refresh Close User's Manual U17246EJ2V0UM 167 CHAPTER 7 WINDOW REFERENCE Related operations (1) Online assembly To change the disassembled contents, move the cursor to the mnemonic field (the overwrite and insertion modes are alternately selected by pressing the Insert key). If an attempt is made to move the cursor to another line after the disassembled contents have been changed in the mnemonic field, the new contents are checked. If the new contents are illegal, the code data on the line where the contents have been changed is indicated as '*'. The contents changed in the mnemonic field are written into the memory by pressing the Enter key. By pressing the Enter key, the new contents are checked. If even one line is illegal, the new contents are not written into the memory. To discard the contents, press the ESC key. If the contents are correct and if the Enter key is pressed, the contents are written to the memory, and then the cursor moves to the next line in the mnemonic field, so that the data on the next line can be changed. Caution If the number of new instruction bytes is less than the number of previous instruction bytes as a result of changing, as many 'nop' instructions as necessary are inserted. If the number of new instruction bytes is more than the number of previous instruction bytes, the next instruction is overwritten. In this case also, as many 'nop' instructions as necessary are inserted. that straddle over source lines. The same applies to instructions 168 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Assemble Search dialog box This dialog box is used to search the contents in the Assemble window. (Refer to "5. 3. 2 Disassemble display".) Successive character strings included in an input character string and disassembler character string are compared as one blank character. By setting each item and then clicking the - Opening - Explanation of each area - Function buttons Opening When the Assemble window is the current window, select [View] menu -> [Search...], or click the Explanation of each area (1) Find What (2) Match Case (3) Scan Whole Region (4) Direction (5) Address User's Manual U17246EJ2V0UM 169 CHAPTER 7 WINDOW REFERENCE (1) Find What This area is used to specify the data to be searched (up to 256 character). In the default condition, the string selected in the window that called this dialog box is displayed. As necessary, the character string displayed can be changed.Up to 16 input histories can be recorded. (2) Match Case This should be checked to distinguish between uppercase and lowercase. (3) Scan Whole Region This should be checked to search the entire specified range. (4) Direction This area is used to specify the direction of the search. Up Down Forward search. Searches data forward (upward on screen) from the current position of the cursor. Backward search. Searches data backward (downward on screen) from the current position of the cursor (default). (5) Address This area is used to specify the address to be searched. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) Function buttons Find Next Searches the specified data in accordance with a given condition. If the specified character string is found as a result of a search, it is highlighted. To continue searching, click this button again. Sets the specified condition as the search condition and closes this dialog box. Stops searching. Closes this dialog box.(During searching, this button is replaced by the Set Find Stop (searching) Cancel Help 170 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Address move dialog box This dialog box is used to specify the start address from which displaying, as follows. - Memory window - Assemble window - IOR/SFR window - Coverage window Figure 7-21 Address Move Dialog Box (Example: When Memory Window Is Open) - Opening - Explanation of each area - Function buttons Opening When the target window is the current window, select [View] menu -> [Move...]. Explanation of each area (1) To This area is used to specify an address. In the default condition, the string selected in the window that called this dialog box, or the current PC value etc. is displayed. As necessary, the character string displayed can be changed. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) Up to 16 input histories can be recorded. Function buttons OK Cancel Restore Help The corresponding window is displayed from the address. Closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 171 CHAPTER 7 WINDOW REFERENCE Symbol To Address dialog box This dialog box is used to display the address of the specified variable or function, or the value of the specified symbol. (Refer to "5. 3 Source Display, Disassemble Display Function".) Figure 7-22 Symbol To Address Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [View] menu -> [Symbol...]. Explanation of each area (1) Symbol (2) Conversion result display area (3) Radix 172 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Symbol This area is used to specify the variable, function name, symbol name, or line number to be converted. (Refer to "Table 5-5 Specifying Symbols".) The default radix for inputting a numeric value is decimal. Up to 16 input histories can be recorded. To change the contents of this area, click the If bit symbol have been specified, they are converted to the Address.bit format. Also, equations that include bit symbols cannot be specified. The variable, address of the function, value of the symbol, address of the line number, or value of the expression specified in (1) Symbol is displayed. The address value of an I/O port name or IOR/SFR name, the register contents of a register name, or flag value of a PSW flag name is displayed. (3) Radix This area is used to select the radix of the data to be displayed in (2) Conversion result display area. Hex Dec Oct Bin Hexadecimal number (default) Decimal number Octal number Binary number Function buttons OK Cancel Restore If the contents of (1) Symbol have been changed, converts the symbol. After conversion, closes the dialog box if the contents of (1) Symbol have not been changed. Closes this dialog box. Restores the input data to the original status. If the Help User's Manual U17246EJ2V0UM 173 CHAPTER 7 WINDOW REFERENCE Watch window This window is used to display and change specified watch data. (Refer to "5. 6 Watch Function".) This window can also display wide-ranging watch data (such as global variables and public symbols) in real time even during program execution, in the same way as the Memory window. The results of updating and rewriting data in this window will be reflected in the Memory window. Watch data is registered by clicking the - Opening - Explanation of each area - [View] menu (Watch window-dedicated items) - Context menu - Function buttons Opening Click the Wch button, or select [Browse] menu -> [Watch]. 174 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Left field (symbol name display area) (2) Right field (data value display/setting area) (1) Left field (symbol name display area) This area is used to display variable names, symbol names and types, and tag names of structures or unions. '+' is prefixed to the displayed arrays, pointer variables, and structures or unions. These variables are expanded and displayed as follows when they are double-clicked: Table 7-8 Watch Window Display Format (Symbol) First character + Meaning Array, pointer variable, or structure/union Expanded display is performed by double-clicking "+" (first character changes from "+" to "-"). Array Pointer variable Structure/union By double-clicking the "+", all the elements of the variable are displayed in accordance with the type of the array variable. By double-clicking the "+", the data indicated by the pointer is displayed. By double-clicking the "+", all the members of the structure/union are displayed in accordance with the type of the member variable. If a structure or union is defined in the structure or union, the structure name or union name of the internal structure or union is also displayed. The internal structure or union can be also expanded by using "+". - Expanded display variable Expanded display is canceled by double-clicking "-" (first character changes from "-" to "+"). Remark If an array has too many variables and takes too long to expand, a warning message is displayed. Registered watch data changes are performed in the Change Watch dialog box opened by selecting the item to be changed and then selecting Context menu -> [Change Watch...]. A line with an expanded hierarchy, such as the elements of an array, and members of structures and unions cannot be deleted. If an access breakpoint is set for a variable or a symbol in the Watch window, the symbol name display area is highlighted in gold. (2) Right field (data value display/setting area) This area is used to display and change watch data values. A value is updated when execution is stopped. To save a value, select [File ] menu -> [Save As...]. This area is blank if getting data has failed. Values are changed through direct input. The location to be changed is displayed in red and the contents of the change are written into the target memory when the Enter key is pressed. The previous value can be canceled by the ESC key. The display format is as follows: User's Manual U17246EJ2V0UM 175 CHAPTER 7 WINDOW REFERENCE Table 7-9 Watch Window Display Format (Data) Display Data Integer Hexadecimal (0xxxxx)or (xxxxH) Decimal (xxxx)or (xxxxT) Octal (0xxxx)or (xxxxQ) Binary (0bxxxx) or (xxxxY) "Character" Member name Displayed in accordance with specified scope. Single precision/double precision supported The input/display format is as follows: [ + | - ] inf [ + | - ] nan [ + | - ] integer e [ + | - ]exponent [ + | - ] integer.fraction[ e [ + | - ]exponent Data that has been invalidated because of a change in the scope or optimized compiling Contents Character Enumeration type If scope is specified Floating-point type '?' Remark The radix of a data value can be changed on the Context menu for each variable. The display format of "integer" can be changed on the Debugger Option dialog box. [View] menu (Watch window-dedicated items) When this window is the current window, The following items are added on [View] menu. Only the selected item is subject to this manipulation. Create Break Event Beak when Access to this Variable Break when Write to this Variable Break when Read from this Variable Clear Event? Bin Oct Dec Hex String Creates a break event by using the selected item as follows. Creates a break event that can be accessed for read/write. Creates a break event that can be accessed for write. Creates a break event that can be accessed for read. Deletes a break event corresponding to the selected item. Displays the event information of the variable selected. If an event is set, the Event dialog box is opened. Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays hexadecimal numbers. Displays character strings. 176 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Proper Displays the default value of each variable . Symbols are displayed in accordance with the setting of the Debugger Option dialog box (default). Displays in 8-bit units. Displays in 16-bit units. Displays in 16-bit units. [78K] Displays in 32-bit units. [V850] Displays in 32-bit units. Displays the default value of each variable (default). Only this item is valid for a symbol in C language. Symbols in assembly language are displayed in accordance with the setting of the Debugger Option dialog box . Moves up one line. Moves down one line. Forcibly reads IOR/SFR, that are disabled from being read because their values will be changed, or the data of the I/O ports and I/O protect area added in the Add I/O Port dialog box. Byte Half Word [V850] Word Double Word [78K] Adaptive Up Down Compulsion Read Context menu The menu items are effective for the selected line or item, not the position where the mouse pointer was clicked (same operation as when selecting the main menu with the same name). Beak when Access to this Variable Break when Write to this Variable Break when Read from this Variable Clear Event? Change Watch... Delete Watch Bin Oct Dec Hex String Creates a break event that can be accessed for read/write by using the selected item. Creates a break event that can be accessed for write by using the selected item. Creates a break event that can be accessed for read by using the selected item. Deletes a break event corresponding to the selected item. Displays the event information of the variable selected. If an event is set, the Event dialog box is opened. Changes the selected watch data. Opens the Change Watch dialog box. Deletes the selected watch data from the window. Displays the selected line in binary numbers. Displays the selected line in octal numbers. Displays the selected line in decimal numbers. Displays the selected line in hexadecimal numbers. Displays the selected line as a character string. User's Manual U17246EJ2V0UM 177 CHAPTER 7 WINDOW REFERENCE Proper Displays the selected line as the default value of each variable . Symbols are displayed in accordance with the setting of the Debugger Option dialog box (default). Displays the selected line in 8-bit units. Displays the selected line in 16-bit units. Displays the selected line in 16-bit units. [78K] Displays the selected line in 32-bit units. [V850] Displays the selected line in 32-bit units. Displays the selected line as the default value of each variable (default). Only this item is valid for a symbol in C language. Symbols in assembly language are displayed in accordance with the setting of the Debugger Option dialog box . Moves the selected line one line up. Moves the selected line one line down. Byte Half Word [V850] Word Double Word [78K] Adaptive Up Down Function buttons Add... Opens the Add Watch dialog box. If watch data is specified and the Delete Up Down Refresh Close 178 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Quick Watch dialog box This dialog box is used to temporarily display or change specified watch data. (Refer to "5. 6 Watch Function".) Figure 7-24 Quick Watch Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Source window or Assemble window is the current window, select [View] menu -> [Quick Watch...], or click the Explanation of each area (1) Name (2) Symbol name display area (3) Data value display/setting area (4) Display radix selection area (upper left field) (5) Display size selection area (second upper left field) (6) Number User's Manual U17246EJ2V0UM 179 CHAPTER 7 WINDOW REFERENCE (1) Name This area is used to specify the watch data to be displayed. In the default condition, the string selected in the window that called this dialog box is displayed. As necessary, the character string displayed can be changed. Up to 16 input histories can be recorded. If the contents of this area have been changed, the data specified can be displayed in the field below by clicking the (5) Display size selection area (second upper left field) This area is used to select the display size. If the display size is fixed, such as when a variable in C language or register is to be displayed, it cannot be changed. Adaptive Byte Half Word [V850] Word Double Word [78K] Variable : Displays the default value of each variable. Symbol : Displays data with the size set in the Debugger Option dialog box. Displays in 8-bit units. Displays in 16-bit units. Displays in 16-bit units. [78K] Displays in 32-bit units. [V850] Displays in 32-bit units. 180 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (6) Number This area is used to specify the number of data to be displayed (blank or a number of 1 to 256). If this area is blank, data is displayed as a simple variable. If a number of 1 or more is specified, data is displayed as an array variable in the Watch window. If an array variable is displayed, "+" is prefixed to the data. By double-clicking this "+", all the elements of the data are expanded and displayed in accordance with the type of the data ("-" is prefixed to the expanded data. If this "-" is double-clicked, the expanded display is canceled). If the number of data to be displayed is fixed, such as when a variable in C language or register is to be displayed, the specified number of data is invalid. Function buttons View Add Close Displays the data specified in (1) Name in the field below. Adds the data specified in (1) Name to the Watch window. Closes this dialog box. Data that has not actually been written to the target memory will be canceled. User's Manual U17246EJ2V0UM 181 CHAPTER 7 WINDOW REFERENCE Add Watch dialog box This dialog box is used to register watch data to be displayed in the Watch window. (Refer to "5. 6 Watch Function".) Multiple data with the same symbol name can be registered. Figure 7-25 Add Watch Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [View] menu -> [Add Watch...], or click the Explanation of each area (1) Name (2) Radix (3) Size (4) Number 182 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Name This area is used to specify symbol to be added to the Watch window. In the default condition, the string selected in the window that called this dialog box is displayed. As necessary, the character string displayed can be changed. This area is blank if no character string is selected. Up to 16 input histories can be recorded. The input format is as follows: Table 7-10 Watch Window Input Format - Variable Name of C language Variable expression : Variable Name |Variable expression [Constant value | Variable Name] |Variable expression . Member name |Variable expression -> Member name |*Variable expression |&Variable expression - Register name - IOR/SFR name, IOR/SFR bit name - Label and address of immediate value - Register name.bit - IOR/SFR name. bit - Label name.bit , address of immediate value.bit - Specification of scope Elements of array Entity members of structure/union Members of structure/union indicated by pointer Value of pointer variable Address where variable is located How a variable is handled when a scope Is specified is as follows: Table 7-11 How a Variable Is Handled When a Scope Is Specified Scope Specification prog$file#func#var prog$file#var prog$func#var prog$var file#func#var file#var func#var var Program name prog prog prog prog current current current current file file global global file file current current File name Function name func global func global func global func current Variable Name var var var var var var var var User's Manual U17246EJ2V0UM 183 CHAPTER 7 WINDOW REFERENCE (2) Radix This area is used to select the display radix. (Refer to "(4) Display radix selection area (upper left field)" in the Quick Watch dialog box.) (3) Size This area is used to select the display size. (Refer to "(5) Display size selection area (second upper left field)" in the Quick Watch dialog box.) (4) Number This area is used to specify the number of data to be displayed. (Refer to "(6) Number" in the Quick Watch dialog box.) Function buttons Add OK Cancel Restore Help Adds the specified data to the Watch window. The dialog box remains open. Adds the specified data to the Watch window. Closes this dialog box. Closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. 184 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Change Watch dialog box This window is used to change the data on a line selected in the Watch window. (Refer to "5. 6 Watch Function".) A line with an open hierarchy, such as the elements of an array, and members of structures and unions cannot be changed. When watch data is changed, the contents of the selected line are replaced with the new data. The symbol name can be changed even if it results in duplication of a name already in use with existing data. Figure 7-26 Change Watch Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Watch window is the current window, select [View] menu -> [Change Watch...]. Explanation of each area (1) Name (2) Radix (3) Size (4) Number User's Manual U17246EJ2V0UM 185 CHAPTER 7 WINDOW REFERENCE (1) Name This area is used to change a symbol name on a line selected in the Watch window. (Refer to "(1) Name" in the Add Watch dialog box.) (2) Radix This area is used to change the display radix on a line selected in the Watch window . (Refer to "(4) Display radix selection area (upper left field)" in the Quick Watch dialog box.) (3) Size This area is used to change the display size on a line selected in the Watch window. (Refer to "(5) Display size selection area (second upper left field)" in the Quick Watch dialog box.) (4) Number This area is used to change the number of data to be displayed on a line selected in the Watch window. (Refer to "(6) Number" in the Quick Watch dialog box.) Function buttons Add OK Cancel Restore Help Cannot be selected. Replaces the data on a line selected in the Watch window with the specified data, and then closes this dialog box. Closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. 186 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Local Variable window This window is used to display the local variable in the current function and change the local variable values. (Refer to "5. 6 Watch Function".) It is linked with the Jump function of the Stack window, and displays the local variable in the function jumped when jumping to the Source window. A number of other operations using Context menu, Function buttons, etc., can be performed in this window. Figure 7-27 Local Variable Window - Opening - Explanation of each area - Context menu - Function buttons Opening Click the Loc button, or select [Browse] menu -> [Local Variable]. Explanation of each area (1) Left field (local variable name display area) (2) Right field (local variable value display/setting area) User's Manual U17246EJ2V0UM 187 CHAPTER 7 WINDOW REFERENCE (1) Left field (local variable name display area) This area displays local variable name. (Refer to "(1) Left field (symbol name display area)" in the Watch window.) Auto, Internal Static, and Register variables can be displayed. This area cannot be edited. (2) Right field (local variable value display/setting area) This area is used to display and change local variable values. (Refer to "(2) Right field (data value display/setting area)" in the Watch window.) [View] menu (Local variable window-dedicated items) When this window is the current window, The following items are added on [View] menu. Bin Oct Dec Hex String Proper Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays octal numbers. Displays character strings. Displays the default value of each variable (default). Context menu The menu items are effective for the selected line or item, not the position where the mouse pointer was clicked (same operation as when selecting the main menu with the same name). Add Watch... Bin Oct Dec Hex String Proper Opens the Add Watch dialog box. Displays the selected line in binary numbers. Displays the selected line in octal numbers. Displays the selected line in decimal numbers. Displays the selected line in hexadecimal numbers. Displays the selected line as a character string. Displays the selected line as the default value of each variable . Symbols are displayed in accordance with the setting of the Debugger Option dialog box (default). Function buttons Refresh Close Updates the contents of this window with the latest watch data. Closes this window. 188 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Stack window This window is used to display or change the current stack contents of the user program. (Refer to "5. 6. 7 Stack trace display function".) The window corresponding to the stack contents can be jumped to using the Jump function. A number of other operations using Context menu, Function buttons, etc., can be performed in this window. Caution1 The stack trace display function may not operate correctly if there is a function that does not create a stack frame. [V850] Caution 2 The stack trace display function may not operate properly when there is a function (noauto, norec, etc.) that does not push the frame pointer (HL) onto the stack, or when the -qf option is provided as an optimization option during compiling. [78K] Caution3 [ERROR] may be displayed during prologue or epilogue processing of a function. Figure 7-28 Stack Window - Opening - Explanation of each area - [View] menu (Stack window-dedicated items) - Context menu - Function buttons Opening Click the Stk button, or select [Browse] menu -> [Stack Trace]. User's Manual U17246EJ2V0UM 189 CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Left field (stack frame number display area) (2) Center field (stack frame contents display area) (3) Right field (stack contents display/setting area) (1) Left field (stack frame number display area) This area assigns numbers to and displays the stack contents. A stack frame number is a natural number starting from 1. The shallower the nesting of the stack, the higher the number. This means that a function having stack number one higher than that of a certain function is the function that calls the certain function. (2) Center field (stack frame contents display area) This area displays the stack frame contents. It displays function names or local variable names. Note, however, that this area cannot be edited. (a) If the stack contents consist of a function They are displayed as follows: [program name$file name#function name (argument list) #line number] If this line is double-clicked, the operation will be the same as jumping to the Source window of the Jump function (i.e., the local variable in the function to which execution has jumped will be displayed in the Local Variable window).If the function has a local variable, the local variable will be displayed on the next and subsequent lines. (b) If the stack contents consist of a local variable Its type and name are displayed. (Refer to "Table 7-8 Watch Window Display Format (Symbol)".) Note that the internal Static and Register variables are not displayed. (3) Right field (stack contents display/setting area) This area is used to display or change the stack contents. (a) If the stack contents are a function "--" is displayed and the function cannot be changed. (b) If the stack contents are a local variable The variable value is displayed. (Refer to "Table 7-9 Watch Window Display Format (Data)".) [View] menu (Stack window-dedicated items) When this window is the current window, The following items are added on [View] menu. Bin Oct Dec Hex Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays octal numbers. 190 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE String Proper Displays character strings. Displays the default value of each variable (default). Context menu Bin Oct Dec Hex String Proper Displays the selected line in binary numbers. Displays the selected line in octal numbers. Displays the selected line in decimal numbers. Displays the selected line in hexadecimal numbers. Displays the selected line as a character string. Displays the selected line as the default value of each variable . Symbols are displayed in accordance with the setting of the Debugger Option dialog box (default). Displays the corresponding source text and source line from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) If no line information exists at the jump destination address, however, you cannot jump. Opens the Source window. If an active Source window is open, that window is displayed in the forefront (so that it can be manipulated). Disassembles and displays starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Assemble window. If an active Assemble window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the coverage measurement results starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Coverage window. If an active Coverage window is open, that window is displayed in the forefront (so that it can be manipulated). Source Text Assemble Memory Coverage Function buttons Refresh Shrink <<< Expand >>> (when the Updates the contents of this window with the latest watch data. Collapses the local variable list of the selected function. Displays the local variable list of the selected function. Closes this window. User's Manual U17246EJ2V0UM 191 CHAPTER 7 WINDOW REFERENCE Memory window This window is used to display and change the memory contents. (Refer to "5. 7 Memory Manipulation Function".) Other operations using Context menu, Function buttons, etc., can be performed in this window. Moreover, there are two statuses, Active status and static status, for this window. When the window is in the active status, it has the Trace result with linking window, Jump function . (Refer to "5. 17 Functions Common to Each Window".) Remark The display start position when the this window is opened is as follows: First time : Display starts from the first address of the RRM function area. Second and subsequent times : Display starts from the address at which an active status window was closed. (if an active status window has never been closed, display starts from the first display start position). Figure 7-29 Memory Window - Opening - Explanation of each area - [View] menu (Memory window-dedicated items) - Context menu - Function buttons Opening Click the Mem button, or select [Browse] menu -> [Memory]. Explanation of each area (1) Addr (2) +0 +1 +2.... (3) 0 1 2 3.... 192 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Addr This area displays memory addresses. Caution The address width changes when memory banks are used. [78K0] (2) +0 +1 +2.... This area is used to display and change memory contents. Values are changed through direct input. The location to be changed is displayed in red and the contents of the contents of the change are written into the target memory when the Enter key is pressed. The previous value can be canceled by the ESC key. Up to 256 bytes can be specified at one time. (3) 0 1 2 3.... This area is used to display and change the memory contents in ASCII characters. This area is displayed when [View] menu -> [Ascii] is selected. Data can be changed in this area in the same manner as in the memory display area. The changing method is the same as in (2) +0 +1 +2..... [View] menu (Memory window-dedicated items) The following items are added in the [View] menu , when the Memory Window is active. Bin Oct Dec Hex Nibble Byte Half Word [V850] Word Double Word [78K] Ascii Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays hexadecimal numbers (default). Displays in 4-bit units. Displays in 8-bit units (default). Displays in 16-bit units. Displays in 16-bit units. [78K] Displays in 32-bit units. [V850] Displays in 32-bit units. Selects whether ASCII characters are displayed or not. Checked: Displayed Not checked: No display (default) Displays in little endian (default). Displays in big endian. Little Endian Big Endian User's Manual U17246EJ2V0UM 193 CHAPTER 7 WINDOW REFERENCE Context menu The menu items are effective for the selected line or item, not the position where the mouse pointer was clicked (same operation as when selecting the main menu with the same name). Move... Bin Oct Dec Hex Nibble Byte Half Word [V850] Word Double Word [78K] Ascii Moves the display position. Opens the Address move dialog box. Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays hexadecimal numbers (default). Displays in 4-bit units. Displays in 8-bit units (default). Displays in 16-bit units. Displays in 16-bit units. [78K] Displays in 32-bit units. [V850] Displays in 32-bit units. Selects whether ASCII characters are displayed or not. Checked: Displayed Not checked: No display (default) Function buttons Search... Opens the Memory Search dialog box and searches for character strings from the displayed memory contents, or memory contents. Selected data (a memory value) is displayed in the Memory Search dialog box as data to be searched.If the Memory Search dialog box is opened without data specified, specify data from the keyboard. The results of the search is highlighted in the Memory window. Searches the memory contents satisfying the search condition set in the Memory Search dialog box, forward (upward on screen) from the address at the cursor position. This button is displayed as the << >> Stop(searching) Refresh Modify... Close 194 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Memory Search dialog box This dialog box is used to search the memory contents of the part of the Memory window at which the cursor is located. (Refer to "5. 7 Memory Manipulation Function".) If the cursor is placed in (2) +0 +1 +2.... in the Memory window, the specified data is treated as a binary data string, and if the cursor is placed in (3) 0 1 2 3...., the specified data is treated as an ASCII character string, and the contents of these respective areas are searched. By setting each item and then clicking the - Opening - Explanation of each area - Function buttons Opening When the Memory window is the current window, select [View] menu -> [Search...], or click the Explanation of each area (1) Find What (2) Unit (3) Scan Whole Region (4) Direction (5) Address User's Manual U17246EJ2V0UM 195 CHAPTER 7 WINDOW REFERENCE (1) Find What This area is used to specify the data to be searched. In the default condition, the string selected in the window that called this dialog box is displayed. As necessary, the character string displayed can be changed. Up to 16 input histories can be recorded. (a) When searching in (2) +0 +1 +2.... Up to 16 data items can be specified. Delimit each data with a "blank character". (b) When searching in (3) 0 1 2 3.... Up to 256 characters can be specified. A "blank character" in the data is treated as a blank character. (2) Unit This area is used to specify the number of bits of the data to be searched in (2) +0 +1 +2..... Byte Half Word [V850] Word Double Word [78K] Searches the data as 8-bit data (default). Searches the data as 16-bit data. Searches the data as 16-bit data. [78K] Searches the data as 32-bit data. [V850] Searches the data as 32-bit data. (3) Scan Whole Region This should be checked to search the entire specified range. (4) Direction This area is used to specify the direction of the search. Up Down Forward search. Searches data forward (upward on screen) from the current position of the cursor. Backward search. Searches data backward (downward on screen) from the current position of the cursor (default). (5) Address This area is used to specify the address to be searched. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) 196 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Function buttons Find Next Searches the specified data in accordance with a given condition. If the specified character string is found as a result of a search, it is highlighted. To continue searching, click this button again. Sets the specified condition as the search condition and closes this dialog box. Stops searching. Closes this dialog box. (During searching, this button is replaced by the Set Find Stop (searching) Cancel Help User's Manual U17246EJ2V0UM 197 CHAPTER 7 WINDOW REFERENCE Memory Fill dialog box This dialog box is used to fill the memory contents in the Memory window with specified codes (fill code). (Refer to "5. 7 Memory Manipulation Function".) Figure 7-31 Memory Fill Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Edit] menu -> [Memory] -> [Fill...]. Explanation of each area (1) Address (2) fill code 198 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Address This area is used to specify the memory address range whose contents are filled. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) (2) fill code This area is used to specify the data (fill code) used when filling the range specified in (1) Address. Up to 16 binary data strings (byte data strings) can be specified. Delimit each data with a "blank character". Function buttons OK Stop (filling) Cancel Restore Help Fills the specified data in accordance with a given condition. Stops filling. Closes this dialog box. (During filling, this button is replaced by the User's Manual U17246EJ2V0UM 199 CHAPTER 7 WINDOW REFERENCE Memory Copy dialog box This dialog box is used to copy the memory contents in the Memory window . (Refer to "5. 7 Memory Manipulation Function".) Figure 7-32 Memory Copy Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Edit] menu -> [Memory] -> [Copy...]. Explanation of each area (1) Address This area is used to specify the copy source and copy destination addresses. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) (a) From: Specify the address range (start address -- end address) of the copy source. (b) To: Specify start address of the copy destination. 200 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Function buttons OK Stop (copying) Cancel Restore Help Copies the memory contents in accordance with a given condition. Stops copying. Closes this dialog box. (During copying, this button is replaced by the User's Manual U17246EJ2V0UM 201 CHAPTER 7 WINDOW REFERENCE Memory Compare dialog box This dialog box is used to compare the memory contents in the Memory window. (Refer to "5. 7 Memory Manipulation Function".) Figure 7-33 Memory Compare Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Edit] menu -> [Memory] -> [Compare...]. Explanation of each area (1) Address This area is used to specify the comparison source address and comparison destination address. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) (a) Mem1 Specify the address range (start address -- end address) of the comparison source. (b) Mem2 Specify the start address of the comparison destination. 202 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Function buttons OK Compares the memory contents in accordance with a given condition. If no difference is found as a result of comparison, " Wf200: No difference encountered." is displayed. If a difference is found, the Memory Compare Result dialog box is opened. Stops memory comparison. Closes this dialog box. (During comparison, this button is replaced by the Stop (comparison) Cancel Restore Help User's Manual U17246EJ2V0UM 203 CHAPTER 7 WINDOW REFERENCE Memory Compare Result dialog box This dialog box is displayed if any difference is found in the memory contents when the memory has been compared in the Memory Compare dialog box .(Refer to "5. 7 Memory Manipulation Function".) Figure 7-34 Memory Compare Result Dialog Box - Explanation of each area - Function buttons Explanation of each area (1) (comparison result display area) This area displays the results of comparing the memory. Only differences that have been found as a result of comparison are displayed. Caution The address width changes when memory banks are used. [78K0] (a) Mem1 Addr Displays a comparison source address in which a difference has been found. (b) Memory Displays the data in which a difference has been found (Left: Comparison source data, Right: Comparison destination data ). (c) Mem2 Addr Displays the comparison destination address at which a difference has been found. 204 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Function buttons Close Help Closes this dialog box. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 205 CHAPTER 7 WINDOW REFERENCE DMM dialog box This dialog box is used to set addresses and data for DMM (Dynamic Memory Modification). (Refer to "5. 7. 3 Modifying memory contents (DMM function)".) Figure 7-35 DMM Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Edit] menu -> [Memory] -> [Modify...], or click the Explanation of each area (1) Address (2) Data (3) Data Size 206 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Address This area is used to specify the address to which data is to be written. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) (2) Data This area is used to specify the data to be written to the memory address specified in (1) Address. The default radix for inputting a numeric value is hexadecimal. One binary data string can be specified at one time. Specify the data size in (3) Data Size. (3) Data Size This area is used to specify the size of the data specified in (2) Data to be written. Byte Half Word [V850] Word Double Word [78K] Writes the data as 8-bit data. Writes the data as 16-bit data. Writes the data as 16-bit data. [78K] Writes the data as 32-bit data. [V850] Writes the data as 32-bit data. Function buttons OK Cancel Restore Help Writes the data in accordance with a given condition. Closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 207 CHAPTER 7 WINDOW REFERENCE Register window This window is used to display and change registers (program registers/system registers: [V850] ) (generalpurpose registers/control registers: [78K] ). (Refer to "5. 8 Register Manipulation Function".) Other operations using Context menu, Function buttons, etc., can be performed in this window. Each area in this window are the jump pointer of the Jump function. Figure 7-36 Register Window - Opening - Explanation of each area - [View]menu (Register window-dedicated items) - Context menu - Function buttons Opening Click the Reg button, or select [Browse] menu -> [Register]. Explanation of each area (1) Register bank setting area [78K0] (2) Upper field (program register [V850] /general-purpose register [78K] display area) (3) Lower field (system register [V850] /control register [78K] display area) 208 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Register bank setting area [78K0] This area is used to display and set general-purpose register bank numbers. (a) Register Bank : Sets the register bank number displayed in this area. (b) Current Bank : Displays the register bank number that is currently set. (2) Upper field (program register [V850] /general-purpose register [78K] display area) This area is used to display and change the program registers [V850] /general-purpose registers [78K] . Register values are changed through direct input. The location to be changed is displayed in red and the contents of the contents of the change are written into the target memory when the Enter key is pressed. The previous value can be canceled by the ESC key. Caution When overflow of a register occurs due to an illegal value entered by the user, the register will be updated with a value of 0xFFFFFFFF. [V850] (3) Lower field (system register [V850] /control register [78K] display area) This area is used to display and change the system registers [V850] /control registers [78K] . By double-clicking "+", flag name and flag value are displayed (first character changes from "+" to "-"). Expanded display is canceled by double-clicking "-" (first character changes from "-" to "+"). Register values are changed through direct input. The location to be changed is displayed in red and the contents of the contents of the change are written into the target memory when the Enter key is pressed. The previous value can be canceled by the ESC key. Caution When overflow of a register occurs due to an illegal value entered by the user, the register will be updated with a value of 0xFFFFFFFF. [V850] Remark When memory banks are used, the address width of the PC register increases by 8 bits. [78K0] [View]menu (Register window-dedicated items) The following items are added in the [View] menu , when the Register window is active. Bin Oct Dec Hex Absolute Name [78K] Function Name [78K] Pick Up [V850] Select... [V850] Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays hexadecimal numbers (default). Displays register names as absolute names. Displays register names as function names (default). Displays only the registers selected in the Register Select dialog box. Opens the Register Select dialog box. User's Manual U17246EJ2V0UM 209 CHAPTER 7 WINDOW REFERENCE Context menu Add Watch... Bin Oct Dec Hex Pick Up [V850] Select... [V850] Registers a selected character string to the Watch window. Opens the Add Watch dialog box. Displays the selected line in binary numbers. Displays the selected line in octal numbers. Displays the selected line in decimal numbers. Displays the selected line in hexadecimal numbers (default). Displays only the registers selected in the Register Select dialog box. Selects the register to be displayed Opens the Register Select dialog box. Function buttons Refresh Close Updates the contents of the window with the latest data. Closes this window. 210 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Register Select dialog box [V850] This dialog box is used to select registers that are not displayed in the Register window. (Refer to "5. 8 Register Manipulation Function".) Figure 7-37 Register Select Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Register window is the current window, select [View] menu -> [Select...]. Explanation of each area (1) Display, No Display This area is used to select registers that are displayed in the Register window, and those that are not. (a) Display Registers displayed in the Register window. (b) No Display Registers not displayed in the Register window. (c) Button The following buttons are used to change register to be displayed in the Register window. << Show Hide >> << Show All Hide All >> Moves the register selected from the (b) No Display list to (a) Display. Moves the register selected from the (a) Display list to (b) No Display. Moves all registers to (a) Display. Moves all registers to (b) No Display. User's Manual U17246EJ2V0UM 211 CHAPTER 7 WINDOW REFERENCE Two or more registers can be selected by clicking any of the above buttons while holding down the Ctrl or Shift key. Function buttons OK Cancel Restore Help Reflects the selection in this dialog box in the Register window and closes this dialog box. Cancels the changes and closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. 212 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE IOR/SFR window This window is used to display and change the contents of periferal I/O register (IOR) [V850] / SFR [78K] and the I/O ports that have been registered in the Add I/O Port dialog box. (Refer to "5. 8 Register Manipulation Function".) A number of other operations using Context menu, Function buttons, etc., can be performed in this window. Caution However, that the values of read-only IOR/SFR and I/O ports cannot be changed. In addition, the IOR/SFR and I/O ports that cause the device to operate when they are read are read-protected and therefore cannot be read. To read these registers, select a register, and select and execute [Compulsion Read] from the Context menu. Remark1 The display start position when the window is opened is as follows. First time: Display from IOR/SFR of minimum address Second and subsequent times: Display from first IOR/SFR when window was last closed Remark2 If the device supports programmable I/O registers and a programmable I/O area has been set in the Configuration dialog box, the programmable I/O registers and expansion peripheral I/O registers are also displayed. If the value of an I/O port address is defined, the I/O port name is displayed in light color. [V850] Figure 7-38 IOR Window User's Manual U17246EJ2V0UM 213 CHAPTER 7 WINDOW REFERENCE Figure 7-39 SFR Window - Opening - Explanation of each area - [View] menu (IOR/SFR window-dedicated items) - Context menu - Function buttons Opening Click the IOR/SFR button, or select [Browse] menu -> [IOR/SFR]. Explanation of each area (1) Name (2) Attribute (3) Value 214 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Name This area displays the names of IOR/SFR and I/O ports. If the value of an I/O port address is not defined, the I/O port name displayed in light color. (2) Attribute This area displays the attributes of IOR/SFR and I/O ports. This area displays the read/write attributes, access types, and displays and absolute addresses from the left side. When the bit IOR/SFR is displayed, bit-offset value is also displayed. It can be specified whether this area is displayed or not, by selecting [View] menu -> [Attribute]. Read/Write Attribute R W R/W Access Type 1 8 16 32 [V850] Can be accessed in Bit units. Can be accessed in Byte units. Can be accessed in Half Word units. [V850] Can be accessed in Word units. [78K] Can be accessed in Word units. Read only Write only Read/write (3) Value This area is used to display and change the contents of a IOR/SFR and I/O port. The contents are displayed differently as follows, depending on the attribute: Black Display -** Read only or read/write Write only Value changes if read Values are changed through direct input. The location to be changed is displayed in red and the contents of the contents of the change are written into the target memory when the Enter key is pressed. The previous value can be canceled by the ESC key. Note that the values of read-only IOR/SFR and I/O ports cannot be changed. The value of read-protected IOR/SFR and I/O ports can be read by selecting Context menu -> [Compulsion Read]. User's Manual U17246EJ2V0UM 215 CHAPTER 7 WINDOW REFERENCE [View] menu (IOR/SFR window-dedicated items) When this window is the current window, The following items are added on [View] menu. Bin Oct Dec Hex Sort By Name Sort By Address Unsort Attribute Pick Up Select... Compulsion Read Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays octal numbers (default). Displays in alphabetical order. Displays in address order (default). Does not sort. Switches on/off display of (2) Attribute. Displays only the registers selected in the IOR/SFR Select dialog box. Opens the IOR/SFR Select dialog box. Forcibly reads the IOR/SFR that are disabled from being read because their values will be changed, or the data of the I/O ports and I/O protect area added in the Add I/O Port dialog box. Context menu Move... Add Watch... Add I/O Port... Bin Oct Dec Hex Sort By Name Sort By Address Unsort Attribute Pick Up Select... Compulsion Read Opens the Address move dialog box. Opens the Add Watch dialog box. Opens the Add I/O Port dialog box. Displays binary numbers. Displays octal numbers. Displays decimal numbers. Displays octal numbers (default). Displays in alphabetical order. Displays in address order (default). Does not sort. Switches on/off display of (2) Attribute. Displays only the registers selected in the IOR/SFR Select dialog box. Opens the IOR/SFR Select dialog box. Forcibly reads the IOR/SFR that are disabled from being read because their values will be changed, or the data of the I/O ports and I/O protect area added in the Add I/O Port dialog box. 216 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Function buttons Refresh Close Updates the contents of this window with the latest watch data. Closes this window. User's Manual U17246EJ2V0UM 217 CHAPTER 7 WINDOW REFERENCE IOR/SFR Select dialog box This dialog box is used to select periferal I/O register (IOR) [V850] / SFR [78K] and I/O ports that are not displayed the IOR/SFR window. (Refer to "5. 8 Register Manipulation Function".) It is also used to specify the sequence in which registers and ports are displayed. Figure 7-40 IOR Select Dialog Box Figure 7-41 SFR Select Dialog Box - Opening - Explanation of each area - Function buttons Opening When the IOR/SFR window is the current window, select [View] menu -> [Select...]. 218 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Display, Pick Up, No Display (2) Arrange (3) Sort by (1) Display, Pick Up, No Display This area is used to select IOR/SFR or I/O ports that are displayed in the IOR/SFR window, and those that are not. (a) Display The IOR/SFR or I/O ports displayed in the IOR/SFR window. (b) No Display The IOR/SFR or I/O ports not displayed in the IOR/SFR window. (c) Pick Up The following buttons are used to change IOR/SFR or I/O ports to be displayed in the IOR/SFR window. << Show Hide >> << Show All Hide All >> Moves IOR/SFR or I/O ports selected from (b) No Display list to (a) Display. Moves IOR/SFR or I/O ports selected from (a) Display list to (b) No Display. Moves all IOR/SFR or I/O ports to (a) Display. Moves all IOR/SFR or I/O ports to (b) No Display. Two or more registers can be selected by clicking any of the above buttons while holding down the Ctrl or Shift key. (2) Arrange The following buttons are used to change the display sequence in (a) Display. Top Up Down Bottom Moves the selected IOR/SFR or I/O port to the top of the list. Moves the selected IOR/SFR or I/O port one line up. Moves the selected IOR/SFR or I/O port one line down. Moves the selected IOR/SFR or I/O port to the bottom of the list. (3) Sort by The following buttons are used to change the display sequence in (b) No Display. Name Address Displays in alphabetical order. Displays in address order. User's Manual U17246EJ2V0UM 219 CHAPTER 7 WINDOW REFERENCE Function buttons OK Cancel Restore Help Reflects the selection in this dialog box in the IOR/SFR window and closes this dialog box. Cancels the changes and closes this dialog box. Restores the status before this dialog box was opened. Displays this dialog box online help files. 220 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Add I/O Port dialog box This dialog box is used to register an I/O port to be added to the IOR/SFR window. (Refer to "5. 8 Register Manipulation Function".) Figure 7-42 Add I/O Port Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Option] menu -> [Add I/O Port...]. Explanation of each area (1) I/O Port List (2) Name (3) Address (4) Access (5) Read/Write User's Manual U17246EJ2V0UM 221 CHAPTER 7 WINDOW REFERENCE (1) I/O Port List This area lists the I/O ports currently registered. If a new I/O port is registered, it is added to this list. An I/O port already registered can be selected and changed or deleted by Function buttons. (2) Name This area is used to specify an I/O port name to be added (up to 15 characters long). (3) Address This area is used to specify the address of the I/O port to be added. The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol. (Refer to "Table 5-5 Specifying Symbols".) The address that can be set in this area is either a Target area address or IOR/SFR area address. (4) Access This area is used to select the access size of the I/O port to be added. Byte Half Word [V850] Word 8-bit unit (default) 16-bit unit 16-bit unit [78K] 32-bit unit [V850] (5) Read/Write This area is used to specify the access attribute of the I/O port to be added. In the default condition, all the attributes are not checked (i.e., the I/O port can be both read and written). Function buttons OK Cancel Restore Help Add Change Delete Reflects the results of addition in the IOR/SFR window and closes this dialog box. Cancels the changing, closes this dialog box. Restores the original status. Displays this dialog box online help files. Adds an I/O port of the specified address. Changes the setting of the I/O port selected in (1) I/O Port List. Deletes the I/O port selected in (1) I/O Port List. 222 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Timer dialog box This dialog box is used to register and set timer event conditions, and display execution time measurement results. (Refer to "5. 12 Event Function", "5. 9 Timer Function".) The (4) Execution time display area can be constantly displayed as the Timer Result dialog box by clicking the - Opening - Explanation of each area - Function buttons (Related event function) Opening Click the Tim button, or select [Event] menu -> [Timer...]. Explanation of each area (1) Timer Name (2) Start Event, End Event (3) Time (4) Execution time display area (5) Event Manager User's Manual U17246EJ2V0UM 223 CHAPTER 7 WINDOW REFERENCE (1) Timer Name This area is used to set a timer event name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event condition, select from the drop-down list. To display from user program execution until break, specify "Run-Break". (Refer to "5. 9. 2 Run-Break event".) The mark on the left of this area indicates the utilization status of events. (Refer to "Table 5-16 Event Icon".) The gray mark indicates that an event condition is being edited and has not been registered yet. By clicking the left mark, an event condition can be validated or invalidated. (2) Start Event, End Event This area is used to set an event condition for the timer. The number of event conditions that can be registered in this area is one for each of the start and end conditions. Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". (3) Time This area is used to select the unit in which the timer measurement result is to be displayed. nsec usec msec sec min clock Nanoseconds (default) Microseconds Milliseconds Seconds Minutes Clock rate (4) Execution time display area This area displays the results of measuring the execution time of the program. (Refer to "Table 7-12 Measurable Values".) If measurement was not performed, or the measurement result was cleared, an empty field is displayed. Pass Total Average Max Min Number of passes Total execution time in the measurement zone specified by start event and end event conditions Average execution time Maximum execution time Minimum execution time 224 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Table 7-12 Measurable Values Measurable Execution Count 4,294,967,295 times max. (32bits) Product SM+ Measurable Execution Time 7 minutes 9 seconds max. (Resolution: 0.1 us) (a) Function buttons Initialize Copy View Always (5) Event Manager This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) Clears the measurement results. Copies the measurement result to the clipboard in text format. Opens the Timer Result dialog box. Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. User's Manual U17246EJ2V0UM 225 CHAPTER 7 WINDOW REFERENCE Timer Result dialog box This dialog box displays the results of measuring the execution time. (Refer to "5. 9 Timer Function".) By clicking the - Opening - Explanation of each area - Function buttons Opening Select a timer event condition in the Timer dialog box , click the Explanation of each area (1) Execution time display area Same area is Timer dialog box. Refer to "(4) Execution time display area" . Function buttons Initialize Copy Close Help Clears the measurement results. Copies the measurement result to the clipboard in text format. Closes this dialog box. Displays this dialog box online help files. 226 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Trace window This window used to display the trace results. (Refer to "5. 10 Trace Function".) The display is updated when a break occurs or during step execution. This window has Mixed display mode (Trace window). Also, It has "5. 17. 3 Trace result with linking window". A number of other operations using Context menu, Function buttons, etc., can be performed in this window. Figure 7-45 Trace Window - Opening - Explanation of each area - [View]menu (Trace window-dedicated items) - Context menu - Function buttons Opening Click the TrW button, or select [Browse] menu -> [Trace]. Explanation of each area (1) Point mark display area (2) Trace mode display area (3) Trace result display area User's Manual U17246EJ2V0UM 227 CHAPTER 7 WINDOW REFERENCE (1) Point mark display area This area displays the Event Setting Status (Event Mark). If an execution event or access event is set at the corresponding trace address, the mark corresponding to the type of the event is displayed. The mark displayed is not that during trace but an event mark that is set when the trace result is displayed. (2) Trace mode display area This area displays the type of trace mode. A Q S T Unconditional traced or section traced frame Qualify traced frame Step execute frame Delay trigger frame (3) Trace result display area This area displays the trace results. In the SM+, a horizontal line (block information) is displayed to indicate the end of program execution. The "Table 7-13 Cause of Stopping Tracer" is displayed when the tracer is stopped. Table 7-13 Cause of Stopping Tracer Cause Event Break Trace Full Break Non Map Break Write Protect SFR Illegal [78K] IOR Illegal [V850] Step Break Manual Break Stack Overflow [78K] Uninitialize Memory read [78K] Trace Stop [78K0] Security Protect Break by event Break because trace memory is full A non-mapped break has been accessed. An attempt has been made to write to a write-protected area. An illegal access is made to SFR. An illegal access is made to a peripheral I/O register. Step execution break Manual break Break by stack overflow Memory not initialized has been read. Trace stop A security protected area was accessed. Meaning 228 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Whether each of the following sub-areas is displayed or not can be selected in the Trace Data Select dialog box. (a) Frame This area displays the trace flame number. (b) Time This area displays how many clocks the target chip has required since execution of the preceding trace contents was started until execution of the current trace contents is started. The display contents can be switched between clock count display and time display in the Trace Data Select dialog box. In addition, the division ratio of the number of counts can be selected up to 1M in the Extended Option dialog box. The number of clocks and time tag value correspond as follows: [V850] Table 7-14 Number of Clocks and Time Tag Value [V850] Time Tag Value Clock rate Division ratio 1 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 2 3 3 4 4 5 5 Division ratio 2 1 2 2 2 2 3 3 3 3 Division ratio 3 1 2 2 2 2 2 2 2 2 Division ratio 4 (c) Address Data Status (fetch access display) This area displays the results of fetching the program and snap contents. The display contents of (ii) Address Data differ depending on (i) Status display. (i) Status The following types of statuses are available: Program fetch display BRM1 M1 [V850] OP [78K] IF [78K] Blank [V850] Fetching of first byte of first instruction after branch A line is displayed in blue for emphasis if the fetched address is the top of a symbol. Fetching of first byte of instruction Opecode fetch of 2nd and subsequent bytes Invalid fetch or status unknown Fetching of sixth or eighth bytes of instruction User's Manual U17246EJ2V0UM 229 CHAPTER 7 WINDOW REFERENCE Snap display SNAP Snap display Remark When a 6-byte or 8-byte instruction code is displayed, the first 4 bytes are displayed in the first frame, and the other bytes are displayed in the second and third frames. If two instructions are executed at the same time, one frame is displayed on two lines. The instruction code at the lower address is displayed on the first line and the instruction code at the higher address is displayed on the second line. [V850] (ii) Address Data This area displays the address and data. The display contents differ as follows, depending on (i) Status display. Program fetch display Address Data Snap Display Item Address Register IOR / SFR Memory Data Register IOR / SFR Memory (d) Address Data Status (data access display) Snap Type Display Contents Register name IOR name [V850] SFR name [78K] Memory address Register value IOR value [V850] SFR value [78K] Memory contents Displays the fetch address Displays the fetch data This area displays the results of accessing data. Status VECT [78K] RW [78K] R W Vector read Data read/write Data read Data write (e) Jmpaddress (branch source address display) The last address of the branch source is displayed only when the (i) Status is BRM1. 230 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (f) DisAsm This area displays the results of disassembly (only when (i) Status is BRM1 or M1). Remark To display instruction codes when two instructions are simultaneously executed, one instruction is displayed on the first line, and the other instruction is displayed on the second line. [V850] [View]menu (Trace window-dedicated items) The following items are added in the [View] menu , when the Trace window is active. Select... Pick Up Off Search Snap BRM1 Mix Selects the contents to be displayed. Opens the Trace Data Select dialog box. Performs the setting for pickup display. Does not pick up and display (default). Picks up and displays a frame that satisfies the search condition. Picks up and displays a snap frame. Picks up and displays the first M1 fetch frame after a program branch. Specifies whether the source file are displayed in mixed display mode, or not displayed. Checked: Mixed display Not checked: No display (default) Links the Trace window with the following windows: (Refer to "5. 17. 3 Trace result with linking window".) A checked window is linked. Links the Source window. Links the Assemble window. Links the Memory window. Links the Coverage window. Window Synchronize Source Text Assemble Memory Coverage Context menu Move... Trace Clear Select... Pick Up Off Search Snap BRM1 Moves the display position. Opens the Trace move dialog box. Clears the trace data. Selects the contents to be displayed. Opens the Trace Data Select dialog box. Performs the setting for pickup display. Does not pick up and display (default). Picks up and displays a frame that satisfies the search condition. Picks up and displays a snap frame. Picks up and displays the first M1 fetch frame after a program branch. User's Manual U17246EJ2V0UM 231 CHAPTER 7 WINDOW REFERENCE Mix Specifies whether the source file are displayed in mixed display mode, or not displayed. Checked: Mixed display Not checked: No display (default) Links the Trace window with the following windows: (Refer to "5. 17. 3 Trace result with linking window".) Links the Source window. Links the Assemble window. Links the Memory window. Links the Coverage window. Displays the corresponding source text and source line, using the data value at the cursor position as the jump destination address (refer to "5. 17. 2 Jump function"). If no line information exists at the jump destination address, however, you cannot jump. Opens the Source window. If an active Source window window is open, that window is displayed in the forefront (so that it can be manipulated). Disassembles and displays starting from the jump destination address specified by the data value at the cursor position (refer to "5. 17. 2 Jump function"). Opens the Assemble window. If an active Assemble window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position (refer to "5. 17. 2 Jump function"). Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position (refer to "5. 17. 2 Jump function"). Opens the Coverage window. If an active Coverage window is open, that window is displayed in the forefront (so that it can be manipulated). Window Synchronize Source Text Assemble Memory Coverage Source Text Assemble Memory Coverage Function buttons Search... Opens the Trace Search dialog box and searches or picks up trace results. The searched result will be highlighted in the Trace window. This button cannot be selected when a snap frame or BRM1 frame is picked up and displayed. Same function as [View] menu -> [Search...]. Searches forward (upward on screen) for a trace result that satisfies the search condition set in the Trace Search dialog box. This button cannot be selected during pickup display. Searches backward (downward on screen) for a trace result that satisfies the search condition set in the Trace Search dialog box. This button cannot be selected during pickup display. Updates the contents of the window with the latest data. Closes this window. << >> Refresh Close 232 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Trace Search dialog box This dialog box is used to search or pick up trace data in the Trace window. (Refer to "5. 10 Trace Function".) By setting each item and then clicking the - Opening - Explanation of each area - Function buttons Opening When the Trace window is the current window, select [View] menu -> [Search...], or click the Explanation of each area (1) Event Status (2) Access Size (3) Address, Mask(Address setting area) (4) Data, Mask(Data setting area) (5) Scan Whole Region (6) Direction (7) Frame User's Manual U17246EJ2V0UM 233 CHAPTER 7 WINDOW REFERENCE (1) Event Status This area is used to select a status condition. If a status condition is omitted, all frames (All status) are searched. All Status BRM1 Fetch M1 Fetch Opecode Fetch [78K] R/W Read Write Vector Read [78K] (2) Access Size This area is used to select an access size condition. By specifying an access size condition, the access width of a data condition to be detected by an access event is determined. Byte Half Word [V850] Word No Condition Bit Searches for a data condition with 8-bit width (only during 8-bit access). Searches for a data condition with 16-bit width (only during 16-bit access). Searches for a data condition with 16-bit width (only during 16-bit access). [78K] Searches for a data condition with 32-bit width (only during 32-bit access). [V850] Does not search based on access size (nothing can be input to the Data area). Searches for a data condition with 1-bit width (only during 8-bit access). In this case, a search is made for a data condition with 1-bit width. Because of the operation of the simulator, access to a bit is not directly detected; the simulator searches a dummy bit access by internally setting address conditions and data conditions as follows: Input example) Address: FE20.1 Data: 1 Setting of trace search) Address: fe20 Data: 00000010B Mask: 11111101B If another bit of the same address is accessed or if all the 8 bits of the same address are accessed, therefore, an event is detected in accordance with the specified status if the address and bit match the specified value of [address.bit]. All frames (default) First M1 fetch after program branch M1 fetch (including BRM1) Opecode fetch (including M1, BRM1) Data read/write (including R, W) Data read Data write Vector read by interrupt Caution If an access event is specified as a status condition, the alternative of Bit is not displayed. If Bit or 1 is specified, an error occurs. 234 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Remark If no access size condition is specified, a judgment is automatically made from the address condition and data condition, and the following is set: -Bit if the address condition is set in bit units -Byte if the data condition is set in 8-bit units -Half Word if the data condition is set in 16-bit units [V850] -Word if the data condition is set in 16-bit units [78K] -Word if the address condition is set in 32-bit units [V850] -No Condition if no data condition is specified (3) Address, Mask(Address setting area) This area is used to specify an address condition. The default radix for inputting a numeric value is hexadecimal. A symbol can be also specified by a symbol or expression ("Table 5-5 Specifying Symbols"). The following can be set: Table 7-15 Settable Range of Address Condition (Trace) Settable range [V850] 0 <= address value <= 0xFFFFFFFF 0 <= mask value <= 0xFFFFFFFF [78K0] 0 <= address value <= 0xFFFF 0 <= mask value <= 0xFFFF 0 <= address value <= (n<<16) | 0xFFFF 0 <= mask value <= (n<<16) | 0xFFFF [78K0S] 0 <= address value <= 0xFFFF 0 <= mask value <= 0xFFFF None None When banks used (n = max. value of bank number used) When banks not used None None Condition (a) Address Set an address condition (lower address - higher address) (may be omitted). The following can be set: (i) Setting as a point Set a value to only the lower address, or set the same value to the lower address and the higher address. (ii) Setting as a range Set a value to only the lower address, or set the same value to the lower address and the higher address. User's Manual U17246EJ2V0UM 235 CHAPTER 7 WINDOW REFERENCE (iii) Setting as a bit Set a value to only the lower address, or set the same value to the lower address and the higher address. Specify a value in the form of "address.bit". Mask cannot be set. The value of bit, which indicates the bit position, must be 0 <= bit<= 7. (b) Mask Set a mask value for an address value (only when (i) Setting as a point). Mask may be omitted. The address value of a bit whose mask value is 1 may be 0 or 1. Example 1: Address Mask 0x4000 to 0x4000 0xFF With this setting, addresses 0x4000 to 0x40FF satisfy the condition. Example 2: Address Mask 0x4000 to 0x4000 0x101 With this setting, addresses 0x4000, 0x4001, 0x4100, and 0x4101 satisfy the condition. (4) Data, Mask(Data setting area) This area is used to set data conditions. The default radix for inputting a numeric value is hexadecimal. The settable range differs as follows depending on the access size condition specified in (2) Access Size. (Refer to "Table 7-22 Settable Range of Data Condition".) (a) Data Set a data value as data conditions. A data can be also specified by a symbol (refer to "Table 5-5 Specifying Symbols"). (b) Mask Set a mask value for the data value. When a mask is set, the data value for the bit whose mask value is 1 may be 0 or 1. Example 1: Data Mask 0x4000 0xFF With this setting, addresses 0x4000 to 0x40FF satisfy the condition. Example 2: Data 0x4000 236 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Example 2: Mask 0x101 With this setting, addresses 0x4000, 0x4001, 0x4100, and 0x4101 satisfy the condition. (5) Scan Whole Region This should be checked to search the entire specified range. (6) Direction This area is used to specify the direction of the search. Up Down Forward search. Searches data forward (upward on screen) from the current position of the cursor. Backward search (default). Searches data backward (downward on screen) from the current position of the cursor. (7) Frame This area is used to specify a frame number to be searched. The default radix for inputting a numeric value is decimal. A symbol can be also specified by Frame Number Specification Format. Function buttons Find Next Searches the specified data in accordance with a given condition. If the specified frame is found as a result of a search, it is highlighted. To continue searching, click this button again. Sets the specified condition as the search condition and closes this dialog box. Picks up according to the specified condition of data search. If a frame that satisfies the condition is found as a result of a search, it is picked up. To pick up a frame that satisfies a different condition, press this button again. Closes this dialog box. Displays this dialog box online help files. Set Find Pick Up (Stop (during search)) Cancel Help User's Manual U17246EJ2V0UM 237 CHAPTER 7 WINDOW REFERENCE Trace Data Select dialog box This dialog box is used to select items to be displayed in the Trace window. (Refer to "5. 10 Trace Function".) Figure 7-47 Trace Data Select Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Trace window is the current window, select [View] -> [Select...] menu. Explanation of each area (1) Item (2) Radix (3) Pick Up 238 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Item This area is used to select items to be displayed in the Trace window. may not be selected. The field checked is displayed. Frame Timetag Instruction Fetch Address Instruction Fetch Data Instruction Fetch Status Memory Access Address Memory Access Data Memory Access Status Jump Address DisAssemble (2) Radix This area is used to select the radix in which data is to be displayed. Displaying the following items may or may not be selected. Instruction Fetch Data Memory Access Data Data field in (c) Address Data Status (fetch access display) Data field in (d) Address Data Status (data access display) (a) Frame field (b) Time field Whether the clock or time is displayed can be selected. Address field in (c) Address Data Status (fetch access display) Data field in (c) Address Data Status (fetch access display) Status field in (c) Address Data Status (fetch access display) Address field in (d) Address Data Status (data access display) Data field in (d) Address Data Status (data access display) Status field in (d) Address Data Status (data access display) (e) Jmpaddress (branch source address display) field (f) DisAsm field Displaying the following items may or HEX DEC OCT Bin Displays hexadecimal numbers. (default) Displays decimal numbers. Displays octal numbers. Displays binary numbers. (3) Pick Up This area is used to select a pick up condition. Pick Up Off Pick Up Search Frame Pick Up Snap Frame Pick Up BRM1 Frame No pick up display (default) Picks up and displays a frame that satisfies the search condition. Picks up and displays a snap frame. Picks up and displays the first M1 fetch frame after a program branch. User's Manual U17246EJ2V0UM 239 CHAPTER 7 WINDOW REFERENCE Function buttons OK Cancel Restore Help Reflects the results of selection in this dialog box in the Trace window. Closes this dialog box. Restores the original status. Displays this dialog box online help files. 240 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Trace move dialog box This dialog box is used to specify the position from which displaying the Trace window is started. (Refer to "5. 10 Trace Function".) Figure 7-48 Trace Move Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Trace window is the current window, select [View] menu -> [Move...]. User's Manual U17246EJ2V0UM 241 CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Frame selection area This area is used to specify the frame at the destination. 1st frame of last block Trigger frame of last block Last frame of last block Frame No. Moves the display start position to a first frame in the newest block frame of trace data. Moves the display start position to the trigger frame in the newest block frame of trace data. Moves the display start position to the last frame of trace data. Moves the display start position to the specified frame number. (Refer to "Table 7-16 Frame Number Specification Format".) In the default condition, the character string selected in the window that called this dialog box or "Last" is selected. The default radix for inputting a numeric value is decimal. If 0 is specified, the display start position is moved to the first frame of trace data. In addition, frame number can also be specified in the following format. Up to 16 input histories can be recorded. Table 7-16 Frame Number Specification Format Specification +numeric value -numeric value Top First Trigger Last Bottom Abbreviation None None O S T L B Contents Moves backward (downward on screen) the display start position from the frame at the cursor by the specified number of frames (numeric value). Moves forward (upward on screen) the display start position from the frame at the cursor by the specified number of frames (numeric value). Moves the display start position to the first frame Same as "1st frame of last block" Same as "Trigger frame of last block" Same as "Last frame of last block" Moves the display start position to the last frame Function buttons OK Cancel Restore Help Starts trace display from the specified position. Closes this dialog box. Restores the input data to the original status. Displays this dialog box online help files. 242 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Trace dialog box This dialog box is used to register, set, and display trace event conditions. (Refer to "5. 12 Event Function", "5. 10 Trace Function".) The trace event conditions for when performing conditional trace are specified in this dialog box (refer to "Table 5-10 Types of Trace Mode" ). Registration and setting of trace event conditions is done by setting each item (256 items max.) in this dialog box and then clicking the - Opening - Explanation of each area - Function buttons (Related event function) Opening Click the Trc button, or select [Event] menu -> [Trace...]. User's Manual U17246EJ2V0UM 243 CHAPTER 7 WINDOW REFERENCE Explanation of each area (2) (3) (4) (5) (1) Trace Name This area is used to set a trace event name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event condition, select from the drop-down list. The mark on the left of this area indicates the utilization status of events (refer to "Table 5-16 Event Icon"). The gray mark indicates that an event condition is being edited and has not been registered yet. By clicking the left mark, an event condition can be validated or invalidated. (2) Delay Trigger This area is used to set an event condition for a delay trigger (refer to "5. 10. 5 Setting conditional trace"). For the number of items that can be set to this area, refer to "Table 7-17 Number of Events Settable". Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". (3) Section Start, Section End This area is used to set event conditions for starting and stopping a section trace (refer to "5. 10. 5 Setting conditional trace"). For the number of items that can be set to this area, refer to "Table 7-17 Number of Events Settable". Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". (4) Qualify This area is used to set an event condition for a qualify trace (refer to "5. 10. 5 Setting conditional trace"). If two or more events are set, trace is performed when each event occurs. The number of event conditions that can be set in this area is as follows: The number of event link conditions that can be set in this area, refer to "5. 12. 4 Number of enabled events for each event condition". Table 7-17 Number of Events Settable Product name SM+ 64 Total (execution/access) Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". 244 (1) Trace Name Delay Trigger Section Start, Section End Qualify Event Manager User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (5) Event Manager This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. User's Manual U17246EJ2V0UM 245 CHAPTER 7 WINDOW REFERENCE Delay Count dialog box This dialog box is used to set or display delay count values. (Refer to "5. 10 Trace Function".) By setting a delay count value, a trace can be executed the number of times specified by the delay count value after the delay trigger event condition set in the Trace dialog box has been satisfied. (Refer to "5. 10. 5 Setting conditional trace".) Figure 7-50 Delay Count Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Event ] menu -> [Delay Count...]. Explanation of each area (1) Delay Count This area is used to set or display a delay count value (unit: frames). The settable range is 0 (default) to 32767. Function buttons OK Restore Cancel Help Validates the settings and closes this dialog box. Restores the previous settings. Closes this dialog box. Displays this dialog box online help files. 246 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Coverage window This window is used to display the coverage results. (Refer to "5. 11 Coverage Measurement Function".) For details about the display symbols, refer to "Table 7-18 Status List of Coverage Data". Other operations using Context menu, Function buttons, etc., can be performed in this window. Moreover, there are two statuses, Active status and static status, for this window. When the window is in the active status, it has Trace result with linking window. (Refer to "5. 17 Functions Common to Each Window".) Figure 7-51 Coverage Window - Opening - Explanation of each area - [View]menu (Coverage window-dedicated items) - Context menu - Function buttons Opening Click the Cov button, or select [Browse] menu -> [Coverage]. Explanation of each area (1) Addr (2) 0 1 2 3 4 ... User's Manual U17246EJ2V0UM 247 CHAPTER 7 WINDOW REFERENCE (1) Addr This area displays coverage addresses. (2) 0 1 2 3 4 ... This area displays the coverage results. This area has Jump function. To select a display mode, use the [View] menu. Table 7-18 Status List of Coverage Data Display In 1-byte display mode . X R W A $ # % Neither execute, read, nor write Execute only Read only Write only Read and write only Execute and read only Execute and write only Execute, read, and write Meaning In 64/1024-byte display mode [V850] In 64-byte display mode [78K] . X R W A $ # % Neither execute, read, nor write any addresses in display range Execute all addresses in display range Read all addresses in display range Write all addresses in display range Read and write all addresses in display range Execute and read all addresses in display range Execute and write all addresses in display range Execute, read, and write all addresses in display range [View]menu (Coverage window-dedicated items) When this window is the current window, The following items are added on [View] menu. 1Byte 64Bytes 1024Bytes [V850] Displays in 1-byte units (default). Displays in 64-byte units. Displays in 1024-byte units. 248 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Context menu Move... 1Byte 64Bytes 1024Bytes [V850] Source Text Moves the display position. Opens the Address move dialog box. Displays in 1-byte units (default). Displays in 64-byte units. Displays in 1024-byte units. Displays the corresponding source text and source line, using the data value at the cursor position as the jump destination address. (Refer to "5. 17. 2 Jump function".) If no line information exists at the jump destination address, however, you cannot jump. Opens the Source window. If an active Source window is open, that window is displayed in the forefront (so that it can be manipulated). Disassembles and displays starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Assemble window. If an active Assemble window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents starting from the jump destination address specified by the data value at the cursor position. (Refer to "5. 17. 2 Jump function".) Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Clears the coverage measurement results. Opens the Coverage-Clear dialog box. Selects the coverage measurement range as a space of 1 MB or more. Opens the Coverage-Address dialog box. Sets a coverage efficiency measurement condition. Opens the Coverage-Condition Setting dialog box. Displays coverage efficiency. Opens the Coverage-Efficiency View dialog box. Assemble Memory Clear... Select... [V850] Condition... Efficiency... Function buttons Search Searches a coverage result. Opens the Coverage Search dialog box. The searched result will be highlighted in the Coverage window. This button is valid only in the 1-byte display mode. Searches forward (upward on screen) for a coverage result that satisfies the search condition set in the Coverage Search dialog box box, starting from the address at the cursor position. This button is displayed as the << >> Stop (during search) User's Manual U17246EJ2V0UM 249 CHAPTER 7 WINDOW REFERENCE Refresh Close Updates the contents of this window with the latest watch data. Closes this window. 250 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Coverage Search dialog box This dialog box is used to search coverage results in the Coverage window. ( Refer to "5. 11 Coverage Measurement Function".) This dialog box can be called only in the 1-byte display mode. By setting each item and then clicking the - Opening - Explanation of each area - Function buttons Opening When the Coverage window is the current window, select [View] menu -> [Search...], or click the Explanation of each area (1) Search data specification area (2) Scan Whole Region (3) Direction (4) Address User's Manual U17246EJ2V0UM 251 CHAPTER 7 WINDOW REFERENCE (1) Search data specification area Specify a search condition by checking any of the check boxes in this area. If two or more check boxes are checked, the specified address is searched when any of the conditions of the check boxes is satisfied (OR search). No Use [.] Read [R] Write [W] Read x Write [A] Execute [X] Execute x Read [$] Execute x Write [#] Execute x Read x Write [%] Neither execute, read, nor write Read only Write only Read and write Execute only Execute and read Execute and write Execute, read, and write (2) Scan Whole Region This should be checked to search the entire specified range. (3) Direction This area is used to specify the direction of the search. Up Down Forward search. Searches data forward (upward on screen) from the current position of the cursor. Backward search. Searches data backward (downward on screen) from the current position of the cursor (default). (4) Address This area is used to specify the address to be searched. The default radix for inputting a numeric value is hexadecimal. Specification with symbol is also possible. (Refer to "Table 5-5 Specifying Symbols".) Function buttons Find Next Searches the specified data in accordance with a given condition. If the specified character string is found as a result of a search, it is highlighted. To continue searching, click this button again. Sets the specified condition as the search condition and closes this dialog box. Stops searching. Closes this dialog box.(During searching, this button is replaced by the Set Find Stop(searching) Cancel Help 252 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Coverage-Clear dialog box This dialog box is used to clear the coverage measurement results in a specified address range. (Refer to "5. 11 Coverage Measurement Function".) As a result, the contents of the Coverage window and Coverage-Efficiency View dialog box are initialized. Figure 7-53 Coverage-Clear dialog box - Opening - Explanation of each area - Function buttons Opening Select [Option] menu -> [Coverage] -> [Clear...] Explanation of each area (1) Address Range This area is used to specify the addresses whose coverage results are to be cleared. The default radix for inputting a numeric value is hexadecimal. Specification with symbols is also possible. (Refer to "Table 5-5 Specifying Symbols".) Function buttons OK Stop(while cleared) Cancel Restore Help Clears the coverage result in the address range specified in Address Range. Stops clearing the coverage result. Closes this dialog box. This button is displayed as the User's Manual U17246EJ2V0UM 253 CHAPTER 7 WINDOW REFERENCE Coverage-Address dialog box [V850] This dialog box is used to select the coverage measurement range to be displayed in the Coverage window. (Refer to "5. 11 Coverage Measurement Function".) Figure 7-54 Coverage-Address dialog box - Opening - Explanation of each area - Function buttons Opening Select [Option] menu -> [Coverage] -> [Select...] Explanation of each area (1) Address Range This area is used to select any 1 MB space. The selected coverage measurement range is set by clicking the Function buttons OK Cancel Help Validates the coverage measurement range selected in (1) Address Range. Closes this dialog box. Displays this dialog box online help files. 254 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Coverage-Condition Setting dialog box This dialog box is used to specify the contents (condition) to be displayed in the Coverage-Efficiency View dialog box. (Refer to "5. 11 Coverage Measurement Function".) Up to 16 conditions can be registered. Figure 7-55 Coverage-Condition Setting dialog box - Opening - Explanation of each area - Function buttons Opening Select [Option]menu -> [Coverage] -> [Condition...] from the menu bar, or click the Explanation of each area (1) Survey List (2) Address Range, Function (3) Survey Condition User's Manual U17246EJ2V0UM 255 CHAPTER 7 WINDOW REFERENCE (1) Survey List This area displays the list of currently selected conditions. The list contents can be edited using the Function buttons Clear Delete Insert OK View Restore Help Clears the contents of (1) Survey List. Deletes the selected address range or function name from (1) Survey List. Registers the address range or function name specified in (2) Address Range, Function to (1) Survey List. Closes this dialog box. Displays coverage efficiency. Opens the Coverage-Efficiency View dialog box. Restores the input data to the original status. Displays this dialog box online help files. 256 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Coverage-Efficiency View dialog box This dialog box is used to display the coverage efficiency of the coverage results in the range specified in the Coverage-Condition Setting dialog box. (Refer to "5. 11 Coverage Measurement Function".) Figure 7-56 Coverage-Efficiency View dialog box - Openig - Explanation of each area - Function buttons Openig Select [Option] menu -> [Coverage] -> [Efficiency...], or click the Explanation of each area (1) Survey List (2) Results(%) User's Manual U17246EJ2V0UM 257 CHAPTER 7 WINDOW REFERENCE (1) Survey List This area displays the coverage efficiency measurement range. The area specified in the Coverage-Condition Setting dialog box is displayed in this area. If specification was made by function name, the area is displayed in the "program name$file name#function name" format. (2) Results(%) This area displays the coverage efficiency. (Refer to "Table 7-18 Status List of Coverage Data".) The coverage efficiency indicates how many specified statuses (execution, read, and write) are included in the measurement range, as a percentage. Function buttons OK Condition Help Closes this dialog box. Sets the displayed contents of the coverage efficiency. Opens the Coverage-Condition Setting dialog box. Displays this dialog box online help files. 258 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Event Manager This window is used to manage event conditions. This window allows display, enabling/disabling, and deletion of the Various Event Conditions. (Refer to "5. 12 Event Function".) A number of other operations using Context menu, Function buttons (Related event function), etc., can be performed in this window. The event icon is the jump pointer of the Jump function. Remark Cannot be displayed the Run-Break event in the Event Manager. Figure 7-57 Event Manager (In detailed display mode) - Opening - Explanation of each area - [View]menu (Event manager-dedicated items) - Context menu - Function buttons (Related event function) Opening Click the Mgr button, or select [Event] menu -> [Event Manager]. User's Manual U17246EJ2V0UM 259 CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Event display area This area displays the icons (event icons) of the registered Various Event Conditions. By selecting the context menu -> [Detail], the details can be displayed. (a) [In list displayed] Displays event icon (refer to "Table 5-16 Event Icon"). The event icon is the jump pointer (refer to "5. 17. 2 Jump function"). (b) In detailed display Details of event contents are displayed by using the following key information as a separator. Table 7-19 Separator for Displaying Event Details Key Information Event condition [S] [Z] [A] [R] [B] [78K0] [D] [P] [M] Event link condition [P1] - [P4] [D] [P] Break condition Event link condition on "n"th line Disable condition Pass count condition Status condition Access size condition Address condition Symbol or expression: (actual address) Register condition Register bank condition Data condition Symbol or expression: (actual address) Pass count condition Mask condition Contents 260 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Table 7-19 Separator for Displaying Event Details Key Information [B] Trace condition [M] [T] [D] [S] [E] [Q] Timer condition [S] [E] [U] Snap shot condition [SN] [R] [B] [78K0] [M] [Z] [G] [V850] [F] [78K0] Stub condition [SU] [A] Stub condition Jump address Symbol or expression: (actual address) Snap shot condition Register condition Register bank condition Memory condition Symbol or expression: (actual address) Access size condition Peripheral I/O registers condition SFR condition Timer measurement start condition Timer measurement end condition Timer measurement unit Trace mode Delay trigger condition Delay Count Trace start condition Trace end condition Qualify trace condition Break condition Contents [View]menu (Event manager-dedicated items) The following items are added in the [View] menu , when the Event Manager is active. Select All Event Delete Event Sort By Name Sort By Kind Unsort Detail Overview Selects all the registered events. Deletes a selected event. Displays icons in the order of event names. Displays icons in the order of event types. Does not sort icons (default). Displays the details List display (default) User's Manual U17246EJ2V0UM 261 CHAPTER 7 WINDOW REFERENCE Context menu Sort By Name Sort By Kind Unsort Detail Overview Source Text Displays icons in the order of event names. Displays icons in the order of event types. Does not sort icons (default). Displays the details. List display (default). Displays the corresponding source text and source line, using the position of the selected event as the jump destination address. (Refer to "5. 17. 2 Jump function".) If no line information exists at the jump destination address, however, you cannot jump. Opens the Source window. If an active Source window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the Assemble window from the position of the selected event, which is used as the jump destination address. (Refer to "5. 17. 2 Jump function".) Opens the Assemble window. If an active Assemble window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents from the position of the selected event, which is used as the jump destination address. (Refer to "5. 17. 2 Jump function".) Opens the Memory window. If an active Memory window is open, that window is displayed in the forefront (so that it can be manipulated). Displays the memory contents from the position of the selected event, which is used as the jump destination address. (Refer to "5. 17. 2 Jump function".) Opens the Coverage window. If an active Coverage window is open, that window is displayed in the forefront (so that it can be manipulated). Assemble Memory Coverage Function buttons (Related event function) Describes the all function buttons the related event dialogs (Event Manager, Event dialog box, Event Link dialog box, Break dialog box, Trace dialog box, Snap Shot dialog box, Stub dialog box and Timer dialog box.) OK (Event dialog box, Event Link dialog box) Automatically registers the event condition being edited, if any, and closes this dialog box. In the select mode An event condition is selected and the setting dialog box (indicated on the title bar) that called the Event Link dialog box is displayed again. If the calling dialog box has already been closed, the select mode is returned to the normal mode, and the Event dialog box is not closed. Otherwise, this dialog box will be closed. (Other than above dialog boxes) Automatically registers the event condition being edited, if any, and closes this dialog box. Each event condition becomes valid as soon as it has been registered. 262 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE New (Event Manager) Opens the dialog box to create new event condition. By clicking each button of Set (Event dialog box, Event Link dialog box) Registers the various event conditions. Because the dialog box is not closed even after an event has been registered, new event conditions can be registered. In the select mode An event condition is selected. If there is an event being edited, it is automatically registered and selected. (Other than above dialog boxes) Registers the various event conditions. Because the dialog box is not closed even after an event has been registered, new event conditions can be registered. Each event condition becomes valid as soon as it has been registered. Enable/Disable Validates (enables) or invalidates (disables) the selected event condition. However, event conditions and event link conditions cannot be enabled or disabled. Same operation as the clicking the mark of event icon. Clears the contents of the event condition. Restores the contents of an edited event condition. If an event condition not registered is displayed, all the fields other than the event name field are blank or the default values are set. Closes this dialog box. Even if an event condition is being edited, it is not registered and the dialog box is closed. Displays the help window of this window. Opens the Event Link dialog box. Opens the Break dialog box. Opens the Trace dialog box. Opens the Snap Shot dialog box. Opens the Stub dialog box. Opens the Timer dialog box. Opens the Event Manager. Opens the Event dialog box in the select mode, and selects or newly creates an event condition to be set. The event condition will be added to the area selected when the < Add Event...> button is pressed. Opens the Event Link dialog box in the select mode, and selects or newly creates an event link condition. The event condition will be added to the area selected when the < Add Link...> button is pressed. Opens the various event setting dialog box corresponding to the selected event condition (one). Each setting dialog box displays the contents of the selected event condition. Same operation as double-clicking the event icon or pressing the Enter key. Clear Restore Cancel / Close Help Event Link... Break... Trace... Snap Shot... Stub... Timer... Manager Add Event... Add Link... Open User's Manual U17246EJ2V0UM 263 CHAPTER 7 WINDOW REFERENCE Remove / Delete Deletes the selected event. When an event condition or an event link condition is to be deleted, an error occurs and the event condition or event link condition cannot be deleted if the event is used as a various event condition. Deletes all event conditions Turns on (Expand>>>) or off (Shrink<<<) display of the event manager area. The size of the dialog box is expanded or reduced. The event condition and event link condition selected in Event Manager area add to setting area with a focus. Opens the Select Display Information dialog box. This dialog box is used to change the display mode and rearrange event names. Figure 7-58 Select Display Information Dialog Box Delete All Expand >>> / Shrink <<< Add Info... 264 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Event dialog box This dialog box is used to register and display event conditions. (Refer to "5. 12 Event Function".) Setting of event conditions is done by setting each item in this dialog box and then clicking the - Opening - Explanation of each area - Function buttons (Related event function) Opening In normal mode If the Event dialog box is opened as follows, an event condition can be registered without its purpose being specified. Click the Evn button, or select [Event] menu -> [Event...]. In select mode If the User's Manual U17246EJ2V0UM 265 CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Event Name (2) Event Status (3) Access Size (4) Address, Mask (5) Resister Name (6) Data, Mask (7) Pass Count (8) Event Manager (1) Event Name This area is used to set an event name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event condition, select from the drop-down list. In the select mode, the selected event condition can be set in the event condition setting area of the setting dialog box that called the Event dialog box. The mark on the left of this area indicates the utilization status of events (refer to "Table 5-16 Event Icon"). The gray E. mark indicates that the event condition is being edited and has not been registered yet. (2) Event Status This area is used to select a status condition. By specifying a status condition, the type of the execution event and an access event is determined (if an execution event is specified, nothing can be input to the (3) Access Size and (6) Data, Mask). The status conditions that can be specified are listed below. Table 7-20 Status Condition Status Execution event Execution Access event OPcode Fetch [78K] Vector Read [78K] R/W Read Write Access Register Write Register Memory OP VECT RW R W AC REGW REG MEM Opecode fetch (including pre fetch) Vector read by interrupt Data read/write Data read Data write All access statuses Register write Register Memory EX Program execution Abbreviation Meaning 266 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Status R/W (Data not Equal) [V850] Read (Data not Equal) [V850] Write (Data not Equal) [V850] Abbreviation RWND RND WND Meaning Data read/write (An event occurs only if a data condition is not satisfied.) Data read (An event occurs only if a data condition is not satisfied.) Data write (An event occurs only if a data condition is not satisfied.) Caution The event condition of Register or Memory status can be used for Phase1 of the event link. It cannot be used except for Phase1 of break, trace, snapshot, stub, timer, or event link. These statuses can be used as events of AND condition by being set to Phase1 of event link. Events of AND condition are functions generate events when event conditions set to Phase1 of event link are activated simultaneously. Then event conditions of Execute status can be combined. In case just an event condition of Register or Memory status is set to Phase1 of event link, event conditions of Register status are the same operation as Register Write and those of Memory status are the same operation as Write. (3) Access Size This area is used to select an access size condition. By selecting an access size condition from the drop-down list, the access width of a data condition to be detected by an access event is determined. RemarkI f "OPcode Fetch" or "Vector Read" is specified as a status condition in (2) Event Status, the alternative of Bit is not displayed. [78K] Byte Half Word [V850] Word No Condition Detects data condition with 8-bit width (only during 8-bit access). Detects data condition with 16-bit width (only during 16-bit access). Detects data condition with 16-bit width (only during 16-bit access). [78K] Detects data condition with 32-bit width (only during 32-bit access). [V850] Does not detect access size (nothing can be input to the Data area). User's Manual U17246EJ2V0UM 267 CHAPTER 7 WINDOW REFERENCE Bit Detects data condition with 1-bit width (only during 8-bit access). In this case, a data condition is detected with 1-bit width. Because of the operation of the simulator, access to a bit is not directly detected; the SM+ detects a dummy bit access by internally setting address conditions and data conditions as follows: Input example: Address: FE20.1 Data: 1 Setting of trace search: Address: FE20 Data: 00000010B Mask: 11111101B If another bit of the same address is accessed or if all the 8 bits of the same address are accessed, therefore, an event is detected in accordance with the specified status if the address and bit match the specified value of [address.bit]. When data is written to a bit, all the 8 bits are read/written. If read or read/write is specified as the status, an event occurs if a read operation is performed at this time if the value of the specified [Address.bit] matches. Remark IIf no access size condition is specified, a judgment is automatically made from the address condition and data condition, and the following is set: -Bit if the address condition is set in bit units -Byte if the data condition is set in 8-bit units -Half Word if the data condition is set in 16-bit units [V850] -Word if the address condition is set in 16-bit units [78K] -Word if the address condition is set in 32-bit units [V850] -No Condition if no data condition is specified (4) Address, Mask This area is used to specify an address condition (address value). The default radix for inputting a numeric value is hexadecimal. A data can be also specified by a symbol (refer to "Table 5-5 Specifying Symbols"). Table 7-21 Settable Range of Address Condition (Event) Device [V850] Settable range 0 <= address value <= 0xFFFFFFFF 0 <= mask value <= 0xFFFFFFFF [78K0] When banks not used 0 <= address value <= 0xFFFF 0 <= mask value <= 0xFFFF When banks used 0 <= address value <= (n <<16) | 0xFFFF 0 <= mask value <= (n << 16) | 0xFFFF n = max. value of bank number used n = max. value of bank number used None None Remark 268 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Device [78K0S] Settable range 0 <= address value <= 0xFFFF 0 <= mask value <= 0xFFFF None None Remark (a) Address Set an address condition (lower address - higher address) (may be omitted). The following can be set: (i) Setting as a point Set a value to only the lower address, or set the same value to the lower address and the higher address. (ii) Setting as a range Set a value to the lower address and the higher address. Mask cannot be set. (iii) Setting as a bit Set a value to only the lower address, or set the same value to the lower address and the higher address. Specify a value in the form of address.bit. Mask cannot be set. The value of bit, which indicates the bit position, must be 0 <= bit <= 7. (b) Mask Set a mask value for an address value (only when (i) Setting as a point). Mask may be omitted. The address value of a bit whose mask value is 1 may be 0 or 1. Example 1: Address Mask 0x4000 to 0x4000 0xFF With this setting, addresses 0x4000 to 0x40FF satisfy the condition. Example 2: Address Mask 0x4000 to 0x4000 0x101 With this setting, addresses 0x4000, 0x4001, 0x4100, and 0x4101 satisfy the condition. (5) Resister Name If "Register Write" or "Register" is selected in (2) Event Status, Address, (4) Address, Mask changes to this area. (a) Register This area is used to specify a register. Select a register from the drop-down list, or input a register from the keyboard. Uppercase and lowercase characters are not distinguished. User's Manual U17246EJ2V0UM 269 CHAPTER 7 WINDOW REFERENCE Remark Function names and absolute names can be specified for all general-purpose registers. [V850] Function names and absolute names can be specified for single or paired general-purpose registers. [78K] Select "All" or input the register names directly to specify all registers. (b) Bank [78K0] This area is used to specify a register bank (0-3). Select a register from the drop-down list, or input a register from the keyboard. Omit the specification or select "Current" to specify the current bank. (6) Data, Mask This area is used to set data conditions. The default radix for inputting a numeric value is hexadecimal. The settable range differs as follows depending on the access size condition specified in (3) Access Size. Table 7-22 Settable Range of Data Condition Access Size Byte Half Word [V850] Word 0 <= data value <= 0xFF 0 <= mask value <= 0xFF 0 <= data value <= 0xFFFF 0 <= mask value <= 0xFFFF 0 <= data value <= 0xFFFF [78K] 0 <= mask value <= 0xFFFF [78K] 0 <= data value <= 0xFFFFFFFF [V850] 0 <= mask value <= 0xFFFFFFFF [V850] Data value = 0 or 1 Mask value = Cannot be specified. Settable range Bit (a) Data Set a data value as data conditions. A data can be also specified by a symbol (refer to "Table 5-5 Specifying Symbols"). (b) Mask Set a mask value for the data value. When a mask is set, the data value for the bit whose mask value is 1 may be 0 or 1. Example 1: Data Mask 0x4000 0xFF With this setting, addresses 0x4000 to 0x40FF satisfy the condition. 270 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Example 2: Data Mask 0x4000 0x101 With this setting, addresses 0x4000, 0x4001, 0x4100, and 0x4101 satisfy the condition. (7) Pass Count A pass count specifies how many times an event condition must be satisfied during user program execution before a given condition is satisfied. If no pass count is specified, 1 is assumed (the condition is satisfied as soon as the event condition is satisfied). If "Before Execution" is specified in , this area is invalid. Table 7-23 Pass Count Product Name SM+ 1 to 32767 Range (8) Event Manager This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. User's Manual U17246EJ2V0UM 271 CHAPTER 7 WINDOW REFERENCE Event Link dialog box This dialog box is used to register and display event link conditions. (Refer to "5. 12 Event Function".) Registration of event link conditions is done by setting each item (256 items max.) in this dialog box and then pressing the - Opening - Explanation of each area - Function buttons (Related event function) Opening In normal mode If the Event Link dialog box is opened as follows, an event link condition can be registered without its purpose being specified. Select [Event] menu -> [Event Link...]. In select mode If the 272 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Link Name (2) Phase1, Phase2, Phase3, Phase4 (3) Disable (4) Pass Count (5) Event Manager (1) Link Name This area is used to set a event link name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event link condition, select from the drop-down list. In the select mode, the selected event condition can be set in the event link condition setting area of the setting dialog box that called the Event Link dialog box. The mark on the left of this area indicates the utilization status of event link conditions ("Table 5-16 Event Icon").The mark "L" in gray indicates that an event link condition is being edited and has not been registered yet. (2) Phase1, Phase2, Phase3, Phase4 This area is used to specify the sequence in which event conditions and events are detected. Up to four sequences can be specified. If a disable condition is detected while the program is being executed, however, the event conditions that have so far been satisfied are initialized, and the event conditions are detected again starting from the first event condition. If a link condition and a disable condition are detected at the same time, the disable condition takes precedence. Set Phase 1 -> Phase 2 -> Phase 3 -> Phase 4, in that order.Phase 4 does not have to be set. In this case, an event occurs when the event condition set for the last phase has been detected. An event condition can be set for only Phase 1 or the same event condition can be set for two or more Phases. The number of event conditions that can be set to each phase of this area and while the dialog box, is as follows: Table 7-24 The Number of Event Conditions in Event Link Dialog Box Total (execution/access) 64 Product Name SM+ 10 Each Phase 10 Disable Area (3) Disable This area is used to set an event condition that invalidates the event conditions that have so far been satisfied ("Table 7-24 The Number of Event Conditions in Event Link Dialog Box"). Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". User's Manual U17246EJ2V0UM 273 CHAPTER 7 WINDOW REFERENCE (4) Pass Count This area is used to set a pass count condition (settable range: 1 to 32767). A pass count condition specifies how many times an event condition must be satisfied during user program execution before a given condition is satisfied. If no pass count is specified, 1 is assumed (the condition is satisfied as soon as the event condition is satisfied). (5) Event Manager This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. 274 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Break dialog box This dialog box is used to register; set, and display break event conditions. (Refer to "5. 12 Event Function", "5. 4 Break Function".) Registration and setting of break event conditions is done by setting each item (256 items max.) in this dialog box and then clicking the - Opening - Explanation of each area - Function buttons (Related event function) Opening Click the Brk button, or select [Event] menu -> [Break...]. Explanation of each area (1) Break Name (2) Break Event (3) Event Manager User's Manual U17246EJ2V0UM 275 CHAPTER 7 WINDOW REFERENCE (1) Break Name This area is used to set a break event name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event condition, select from the drop-down list. The mark on the left of this area indicates the utilization status of events. (Refer to "Table 5-16 Event Icon"). The gray mark indicates that an event condition is being edited and has not been registered yet. mark, an event condition can be validated or invalidated. (2) Break Event This area is used to set an event condition for break. The number of event conditions that can be set in this area is as follows: Table 7-25 Number of Events Settable in Break Condition Setting Area Product Name SM+ 64 Total By clicking the left Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". (3) Event Manager This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. 276 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Snap Shot dialog box This dialog box is used to register; set, and display snapshot event conditions. (Refer to "5. 12 Event Function", "5. 13 Snapshot Function".) Registration and setting of snapshot event conditions is done by setting each item (256 items max.) in this dialog box and then clicking the - Opening - Explanation of each area - Function buttons (Related event function) Opening Select [Event] menu -> [Snap Shot...]. Explanation of each area (2) (3) (4) (5) (1) Snap Name: Snap Event: Select Snap Entry: Event Manager User's Manual U17246EJ2V0UM 277 CHAPTER 7 WINDOW REFERENCE (1) Snap Name: This area is used to set a snapshot event name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event condition, select from the drop-down list. The mark on the left of this area indicates the utilization status of events. (Refer to "Table 5-16 Event Icon"). The gray mark indicates that an event condition is being edited and has not been registered yet. mark, an event condition can be validated or invalidated. (2) Snap Event: This area is used to set an event condition for snapshot. The number of event condition and event link condition that can be set in this area is one. Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". (3) Select This area is used to register, change, and delete the snap data, selecting type of data subject to snapshot. By selecting a data type, the item to be displayed in the snap data setting area on the right of this area changes in accordance with the selected area. As snap data, up to 16 registers, IOR/SFR, and memory addresses each can be registered; therefore, a total of 48 registers, IOR/SFR, and memory addresses can be registered. The snap data registered, changed, or deleted in this area is reflected in (4) Snap Entry:. If snap data is selected in (4) Snap Entry:, the contents of the selected snap data are displayed in this area. (a) Register This should be selected to set by a register as snap data. By clicking the left (i) Register Name (Register name setting area) To specify a register name, either directly input one to the text box, or select one from the drop-down list. Uppercase and lowercase characters are not distinguished. A register name can be specified as both a function name and an absolute name. Remark1 Select "All" to specify all registers. [78K] Remark2 The names of program registers and system registers can be specified as Register Name. [V850] The names of general-purpose registers and control registers can be specified as Register Name. [78K] Remark3 The snap data displayed in the Trace window is unified in uppercase letters and in the format of 'absolute name (function name)' [V850] / 'absolute name' [78K] 278 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (ii) Register Bank(Current bank setting area) [78K0] To specify a register bank, either directly input one to the text box, or select one from the drop-down list (0 -3). Remark To specify the current bank, select 'Current'. However, the current bank will be specified even when the specification is omitted. (b) I/O Reg /Sfr This should be selected to set by a IOR/SFR as snap data. (i) I/O Reg Name:/Sfr name:(IOR/SFR snap data setting area) To specify IOR/SFR name, either directly input one to the text box, or select one from the drop-down list. Only the IOR/SFR that can be read can be specified. Uppercase and lowercase characters are not distinguished. The peripheral I/O bit names [V850] / SFR bit names [78K] and the I/O port name registered in the Add I/O Port dialog box cannot be specified. Note that all the register names are displayed in uppercase characters in the Trace window. (c) Memory This should be selected to set by a Memory as snap data. User's Manual U17246EJ2V0UM 279 CHAPTER 7 WINDOW REFERENCE (i) Memory Address: (Memory address setting area) This area is used to specify an address range of the memory. Start address - End address Table 7-26 Address Settable Range (Snap Shot Dialog Box) Device [V850] [78K] Range 0 <= Address value <= 0xFFFFFFFF 0 <= Address value <= 0xFFF (Data memory) 0 <= Address value <= 0xFFFF 0 <= Address value <= 0xFFF (Data memory) If a value is input as only the start address and specifying the end address is omitted, it is assumed that the same value as the start address is specified as the end address. If the specified address range cannot be divided by the access size, the address range is rounded up to a range that can be divided by the access size. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) The default radix for inputting a numeric value is hexadecimal. If addresses are registered or changed in this area by using expressions or symbols, the converted address values are displayed in (4) Snap Entry: along with the specified expressions and symbols. In the Trace window, only the converted address values are displayed. (ii) Memory Display: (Memory display size setting area) To specify the access size, either directly input the size or select the size from the drop-down list. Uppercase and lowercase characters are not distinguished. Byte Half Word [V850] Word Double Word [78K] B HW W DW Snapshot of memory in 8-bit units Snapshot of memory in 16-bit units Snapshot of memory in 32-bit units [V850] Snapshot of memory in 16-bit units [78K] Snapshot of memory in 32-bit units (d) Buttons to manipulate snap data The following buttons are used to register, change, and delete snap data. Insert Registers as snap data. The registered snap data is inserted and displayed at the selected position in (4) Snap Entry:. Changes the contents of the snap data selected in (4) Snap Entry: area to the contents of the snap data specified in this area. Deletes the snap data selected in (4) Snap Entry:. The DEL key performs the same operation. Restores the contents in (4) Snap Entry:. Change Delete Restore 280 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (4) Snap Entry: This area displays a list of registered snap data. The registered snap data is written into the tracer when a snapshot event occurs. If snap data is selected in this area, the contents of the selected snap data are displayed in each setting area. Snap data is displayed as follows: Table 7-27 Snap Data Display Format Display Example Register snap data: RP0[0] RP[Current] All[2] IOR/SFR snap data: PM0 PM1 Memory snap data: 0xFE20 (5) Event Manager This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. User's Manual U17246EJ2V0UM 281 CHAPTER 7 WINDOW REFERENCE Stub dialog box This dialog box is used to register; set, and display stub event conditions. (Refer to "5. 12 Event Function", "5. 14 Stub Function".) Registration and setting of stub event conditions is done by setting each item (256 items max.) in this dialog box and then clicking the - Opening - Explanation of each area - Function buttons (Related event function) Opening Select [Event] menu -> [Stub...]. Explanation of each area (1) Stub Name: (2) Stub Event: (3) Go to: (4) Event Manager: 282 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Stub Name: This area is used to set a stub event name. Directly input an alphanumeric string of up to eight characters as a name. To display the contents of an already created event condition, select from the drop-down list. The mark on the left of this area indicates the utilization status of events. (Refer to "Table 5-16 Event Icon"). The gray mark indicates that an event condition is being edited and has not been registered yet. mark, an event condition can be validated or invalidated. (2) Stub Event: This area is used to set an event condition for stub. The number of event condition and event link condition that can be set in this area is one. Event conditions are easily set by dragging the icon of the event to be set from the event manager area and dropping it in this area. For details, refer to "5. 12. 3 Setting various event conditions". (3) Go to: This area is used to specify the start address of the function that is executed when a stub event occurs. (Refer to "Table 5-17 Start Address of Function to Be Executed (Stub Function)".) The default radix for inputting a numeric value is hexadecimal. An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) (4) Event Manager: This area is used to display the list of the events registered. (Refer to "Table 5-16 Event Icon", "(4) Manipulation in event manager area".) By clicking the left Function Buttons Refer to " Function buttons (Related event function)" in the Event Manager. User's Manual U17246EJ2V0UM 283 CHAPTER 7 WINDOW REFERENCE View File Save dialog box This dialog box is used to save the current display information of the current window to a view file. (Refer to "5. 16. 2 Window display information (view file)".) Figure 7-64 View File Save Dialog Box - Opening - Explanation of each area - Function buttons Opening When the window to be saved is the current window, select [File] menu -> [Save As...]. Explanation of each area (1) Save in :, File name : (2) Save as type : (3) Save range 284 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Save in :, File name : This area is used to specify the file name to be saved. A file name can be directly input from the keyboard, or selected from the list. Up to 257 character string with a extension can be specified. (2) Save as type : This area is used to specify the type (extension) of the file to be saved. (Refer to "Table 5-21 Type of the View Files".) The extension of the file corresponding to the current window is displayed. (3) Save range Specify the range of data to be saved. This area is displayed if the current window to be saved is the following. - Assemble window - Memory window - Coverage window - Source window - Trace window (a) All This should be selected to save the entire range, from the first line to the last line. (b) Screen shot This should be selected to save the area visible on the screen, from the top line on the screen to the bottom line. If the Source window is in the mixed display mode, however, the window contents are saved from the source line that includes the area visible on the screen. (c) Specify Line / Specify Frame / Specify Address This should be selected to specify the start line and end line of the area to be saved. If the start line and end line are omitted, the first line and last line are assumed. If a range of 100 lines / 100 frames / 256 bytes or more is specified, a message dialog box is displayed to indicate the progress of saving. To stop saving midway, click the Specify Frame User's Manual U17246EJ2V0UM 285 CHAPTER 7 WINDOW REFERENCE Specify Address Specify the range of address to be saved . An address can be also specified by a symbol or expression. (Refer to "Table 5-5 Specifying Symbols".) The default radix for inputting a numeric value is hexadecimal. Function buttons Save Cancel Help Restore Saves the display information of the current window to the selected file. After saving, this dialog box is closed. Closes this dialog box without executing anything. Displays this dialog box online help files. Restores the status before this dialog box was opened. 286 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE View File Load dialog box This dialog box is used to read the view files. (Refer to "5. 16. 2 Window display information (view file)".) When a view file is loaded, the reference window (Source window in static status) opens and the display information at saving is displayed. The window to be opened and its status differ as follows, depending on the file to be loaded. - Loading source file to which symbol information has been read If there is a Source window in the active status, it is opened in the static status; otherwise, the Source window is opened in the active status. - Loading source file to which symbol information has not been read, or view file A window of text-format files is opened in the Source window in the static status. Figure 7-65 View File Load Dialog Box - Opening - Explanation of each area - Function buttons Opening Click the Open button or select [File] menu -> [Open...]. Explanation of each area (1) Look In:, File name : (2) Files of type : User's Manual U17246EJ2V0UM 287 CHAPTER 7 WINDOW REFERENCE (1) Look In:, File name : This area is used to specify the file name to be loaded. A file name can be directly input from the keyboard, or selected from the list. Up to 257 character string with a extension can be specified. (2) Files of type : This area is used to specify the type (extension) of the file to be loaded. (Refer to "Table 5-21 Type of the View Files".) Function buttons Open Cancel Help Loads the selected file. After loading the file, this dialog box is closed. Closes this dialog box without executing anything. Displays this dialog box online help files. 288 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Environment Setting File Save dialog box This dialog box is used to save the setting contents of the current window to a setting file. (Refer to "5. 16. 3 Window setting information (setting file)".) Figure 7-66 Environment Setting File Save Dialog Box - Opening - Explanation of each area - Function buttons Opening When the window to be saved is the current window, select [File] menu -> [Environment] -> [Save As...]. Explanation of each area (1) Save in :, File name : (2) Save as type : User's Manual U17246EJ2V0UM 289 CHAPTER 7 WINDOW REFERENCE (1) Save in :, File name : This area is used to specify the file name to be saved. A file name can be directly input from the keyboard, or selected from the list. Up to 257 character string with a extension can be specified. (2) Save as type : This area is used to specify the type (extension) of the file to be saved. (Refer to "Table 5-22 Type of the Setting Files"). The extension of the file corresponding to the current window is displayed. Function buttons Save Cancel Help Restore Saves the setting information of the current window to the selected file. After saving, this dialog box is closed. Closes this dialog box without executing anything. Displays this dialog box online help files. Restores the status before this dialog box was opened. 290 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Environment Setting File Load dialog box This dialog box is used to read the setting files. (Refer to "5. 16. 3 Window setting information (setting file)".) When a setting file is loaded, the target window opens and the setting information at saving is restored. Figure 7-67 Environment Setting File Load Dialog Box - Opening - Explanation of each area - Function buttons Opening select [File] menu -> [Environment] -> [Open...]. Explanation of each area (1) Look In:, File name : (2) Files of type : User's Manual U17246EJ2V0UM 291 CHAPTER 7 WINDOW REFERENCE (1) Look In:, File name : This area is used to specify the file name to be loaded. A file name can be directly input from the keyboard, or selected from the list. Up to 257 character string with a extension can be specified. (2) Files of type : This area is used to specify the type (extension) of the file to be loaded. (Refer to "Table 5-22 Type of the Setting Files".) Function buttons Open Cancel Help Loads the selected file. After loading the file, this dialog box is closed. Closes this dialog box without executing anything. Displays this dialog box online help files. 292 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Reset Debugger dialog box This dialog box is used to initialize the SM+, CPU, and symbol information. Figure 7-68 Reset Debugger Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [File] menu -> [Debugger Reset...]. Explanation of each area (1) Reset subject selection area This area is used to specify what is to be Initialized. Initializes the checked item. Debugger Symbol Target CPU Initializes the SM+ (default). Initializes the symbol information. Initializes the CPU. Function buttons OK Cancel Help Initializes according to the setting. Cancels the changes and closes this dialog box. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 293 CHAPTER 7 WINDOW REFERENCE Exit Debugger dialog box This dialog box is used to select whether the current debug environment is saved to a project file or not before terminating the SM+. (Refer to "5. 16. 1 Debugging environment (project file)".) It can be specified in the Debugger Option dialog box that the SM+ is terminated without this confirmation dialog box being opened. Remark If an attempt is made to terminate the SM+ while the user program is being executed, the following message is displayed " Wfb00: User program is running. Do you want to stop user program?". Figure 7-69 Exit Debugger Dialog Box - Opening - Function buttons Opening - Select [File] menu -> [Exit]. - If forcible termination, such as to terminate the application, has been executed on the task list that terminates Windows. Function buttons Yes Saves the current debug environment to a project file, closes all the windows, and terminates the SM+. If a project file name is not specified, the Project File Save dialog box is opened. If the < Cancel> button is selected on the Project File Save dialog box, the environment is neither saved to a project file nor is the SM+ terminated. (If a project file is loaded or saved during debugger operation, this button has the default focus. ) Closes all the windows and terminates the SM+. (If a project file is not loaded or saved during debugger operation, this button has the default focus.) Closes this dialog box without executing anything. No Cancel 294 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE About dialog box This dialog box displays the version information of the SM+ (the year is displayed in 4 digits). The following version information is displayed: - Product version of SM+ - Version of device file - Version of GUI - Version of debugger DLL - Version of assembler DLL - Version of simulator block - Version of chip information file - Version of Tcl/Tk Figure 7-70 About Dialog Box - Opening - Function buttons Opening Select [Help] menu -> [About...], or click the Function buttons OK Closes this dialog box. User's Manual U17246EJ2V0UM 295 CHAPTER 7 WINDOW REFERENCE Console window This window is used to input commands that control the SM+ . Because the key bind is Emacs-like, the accelerator key is not acknowledged if the Console window is active. However, the F1 key displays the online help files of the Console window. While the Console window is open, an error message window with only an - Opening Opening Select [Browse] menu -> [Console]. 296 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Font dialog box This dialog box is used to select the font and font size to be displayed in the Source window, Watch window, Quick Watch dialog box, Local Variable window, Stack window. Figure 7-72 Font Dialog Box - Opening - Explanation of each area - Function buttons Opening Click the button in the Debugger Option dialog box. Explanation of each area (2) (3) (1) Font Face : Size : Sample User's Manual U17246EJ2V0UM 297 CHAPTER 7 WINDOW REFERENCE (1) Font Face : This area is used to select a font from the fonts currently usable. Only fonts with equal width (fonts with a constant stroke width and a fixed pitch) are enumerated. When a font name is selected from the list, the font name is displayed in the text box, and the font size that can be used with that font is displayed under (2) Size :. (2) Size : This area is used to specify the font size (unit : pt.). On the drop-down list, the font size usable for the font specified in (1) Font Face : is displayed in point units. When the font size is selected from the drop-down list, the selected font size is displayed in this area. The font size can also be directly input to the text box from the keyboard. (3) Sample This area displays a sample character string of the specified font and size. Function buttons OK Cancel Validates the settings and closes this dialog box. Cancels the changes and closes this dialog box. 298 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Browse dialog box This dialog box is used to select the file to be set in the Source Text move dialog box. Remark If this dialog box is opened for the first time after the system has been started up, the directory first specified by the source path is displayed. When the dialog box is opened the second and subsequent times, the previously displayed directory is recorded and displayed again. If the - Opening - Explanation of each area - Function buttons Opening Click the Explanation of each area (1) Look In:, File name : (2) Files of type : User's Manual U17246EJ2V0UM 299 CHAPTER 7 WINDOW REFERENCE (1) Look In:, File name : This area is used to specify the file name to be opened. A file name can be directly input from the keyboard, or selected from the list. Up to 257 character string with a extension can be specified. (2) Files of type : This area is used to specify the type (extension) of the file to be opened (refer to "Table 5-4 File Type Can Be Displayed"). Function buttons Open Cancel Help Sets the selected file. After setting the file, this dialog box is closed. Closes this dialog box without executing anything. Displays this dialog box online help files. 300 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Signal Data Editor window This window is used to set input signal data of any timing to an input pin as a numeric value. (Refer to "6. 1 Pin I/ O Function".) The following data can be displayed or edited in this window: - Newly created signal data - Previously created signal data files - File of signal data previously obtained by performing simulation and saving the results as output signal data Edited signal data can be input to the input pin during simulation by selecting [Edit] menu -> [Signal Input]. This data can also be saved as a signal data file by selecting [Simulator] menu -> [Save/Save As...]. (Refer to "6. 1. 5 Signal data files (*.wvi, *.wvo)".) The saved file contents can be restored by selecting [Simulator] menu -> [Open...]. Figure 7-74 Signal Data Editor Window - Opening - Explanation of each area - Dedicated menu (Signal Data Editor window) - [Signal Data Editor] tool bar - Context menu - Operation Opening Click this button, or select [Simulator] menu -> [Signal Data Editor]. User's Manual U17246EJ2V0UM 301 CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Information bar (2) Client area (1) Information bar It can be specified whether this area is displayed or not, by selecting [View] menu -> [Information Bar]. Displays the wait time unit. The wait time unit can be changed by selecting [Edit] menu -> [Time unit]. (2) Client area (a) Pin area (e) Data area (d) Wait area (c) Mark area (b) Line number area (a) Pin area Displays the pin names edited with the signal data editor. Pin is seleced by selecting [Edit] menu -> [Select Pin...] to open the Select Pin dialog box. Data input to pins can be enabled/disabled by selecting [Edit] menu > [Pin Status]. (b) Line number area Displays line number. This area is used when performing editing in line units. (c) Mark area Displays loop information. The loop information can be edited by selecting [Edit] menu -> [Mark]. The loop information is displayed as follows. Loop start location (endless loop) Loop start location (with loop count) Loop end location 302 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (d) Wait area Displays as wait time the timing at which the data set in (e) Data area is input to the pins. Wait time editing is done by directly writing values in this area. The wait time unit can be changed by selecting [Edit] menu -> [Time unit]. (e) Data area Displays the data input to the pins. Data editing is performed by directly writing values in this area. Dedicated menu (Signal Data Editor window) (1) [Edit] menu Undo Redo Cut Copy Paste Delete Select All Find Select Pin... Time unit main clock usec msec Pin Status Valid InValid Mark Loop Start Loop End Loop Dialog Signal Input Cannot be selected. Cannot be selected. Cuts the selected range and saves it to the clipboard. Copies the selected range and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the selected range. Selects all display data. Cannot be selected. Opens the Select Pin dialog box. The pin(s) for which input signal data is to be created or edited is (are) selected in this dialog box. Selects the wait time unit. Main clock Microsecond Millisecond Selects the input status of the selected pin. Enables data input to the pin. (default) Disables data input to the pin. Sets a mark to the selected (c) Mark area. Sets the loop start mark. Sets the loop end mark. Opens the Loop dialog box. Sets the details of loop information. Inputs signal data to the simulator. User's Manual U17246EJ2V0UM 303 CHAPTER 7 WINDOW REFERENCE Start Stop Reset (2) [View] menu Information Bar (3) [Option] menu Customize... Starts signal input. Stops signal input. Returns the current signal input line to the beginning. Selects whether the information bar is displayed or not. Opens the Customize dialog box. [Signal Data Editor] tool bar Opens the Select Pin dialog box. The pin(s) for which input signal data is to be created or edited is (are) selected in this dialog box. Starts signal input. Stops signal input. Returns the current signal input line to the beginning. Context menu Right-clicking in one of the areas in (2) Client area displays a context menu. The context menus are described below by area. (1) Pin area Valid InValid Select Pin... Enables data input to the pin. (default) Disables data input to the pin. Opens the Select Pin dialog box. The pin(s) for which input signal data is to be created or edited is (are) selected in this dialog box. (2) Line number Cut Copy Paste Delete Cuts the selected range and saves it to the clipboard. Copies the selected range and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the selected range. 304 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (3) Mark area Cut Copy Paste Delete Loop Start Loop End Loop Dialog (4) Wait area Cut Copy Paste Delete (5) Data area Cut Copy Paste Delete Start Signal Input Stop Signal Input Reset Signal Input Cuts the data in the selected cell and saves it to the clipboard . The data in the selected cell becomes "Z" (Hi-Z). Copies the data in the selected cell and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the data in the selected cell. The data in the selected cell becomes "Z" (HiZ). Starts signal input. Stops signal input. Returns the current signal input line to the beginning. Cuts the data in the selected cell and saves it to the clipboard. The data in the selected cell becomes 0. Copies the data in the selected cell and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the data in the selected cell. The data in the selected cell becomes 0. Cuts the selected cell and saves it to the clipboard. Copies the selected cell and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the selected cell. Sets the loop start mark. Sets the loop end mark. Opens the Loop dialog box. Sets the details of loop information. User's Manual U17246EJ2V0UM 305 CHAPTER 7 WINDOW REFERENCE Operation (1) Pin selection (2) Data input (3) Data copy and paste (4) Single-line editing (5) Signal input (6) Operation at CPU reset (1) Pin selection To edit the signal data, it is first necessary to select the pin to be edited. Open the Select Pin dialog box by selecting [Edit] menu -> [Select Pin...] and select the pin to be edited. Once a pin is selected, its name is displayed in (a) Pin area. (2) Data input The data input methods for each area are described below. Input up to 1,048,576 (= 1M) is possible. (a) Mark area Data is input from the context menu. To perform loop processing of input data, set the loop start and loop stop marks by selecting [Loop Start] at the loop start position and [Loop End] at the loop stop position. The loop count can be specified in the Loop dialog box displayed by selecting [Loop Dialog...]. (b) Wait area Data is input by directly inputting numeric values in the relevant fields. Numeric values (decimal code) from 0 to 4,294,967,295 can be specified. Numeric values that exceed 4,294,967,295 can be set by using one more line. (c) Data area Data is input by directly inputting numeric values in the relevant fields. The input rules differ as follows according to the pin type. Digital pins Analog pins Only the following data can be input. "0" (= LOW), "1" (= HIGH), "Z" (= Hi-Z), "z" (= Hi-Z). A value from 0 to 5000 (decimal) can be input. Unit : mV 306 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (3) Data copy and paste The setting values in (c) Mark area/(d) Wait area/(e) Data area can be copied and pasted. However, copied data can be pasted only in the same area. (a) Copy When one or more (a range of) cells are selected, these cells can be copied by selecting [Edit] menu -> [Copy] (or by pressing the button or inputting Ctrl-C). (b) Paste When one or more (a range of) cells are selected, these cells can be pasted by selecting [Edit ] menu -> [Paste] (or by pressing the button or inputting Ctrl-C). When multiple (a range of) cells are selected, the copied data is pasted to the cells repeatedly. (4) Single-line editing Single lines can be edited by selecting (b) Line number area. The method is the same as that described in "(3) Data copy and paste". Data pasted during line paste (insertion) is inserted immediately before the selected line. (5) Signal input The created signal data can be input to the input pins of the simulator while simulation is executed. Moreover, the line whose signal is currently being input (current line) is highlighted in yellow during CPU breaks (this can be changed in the Customize dialog box), in order to display signal input progress. There are the following types of signal data input operations. (a) Signal input start Select [Edit] menu -> [Signal Input] -> [Start]. As a result, signal input starts from the current signal input line (highlighted line). (b) Signal input stop Select [Edit] menu -> [Signal Input] -> [Stop]. This stops signal input. (c) Signal reset Select [Edit] menu -> [Signal Input] -> [Reset]. This returns the current signal input line to the beginning. If signal reset was performed during signal input, input continues from the beginning. (6) Operation at CPU reset When CPU reset occurs, the current signal input line returns to the beginning. If a CPU reset occurs during signal input, input continues from the beginning (same operation as that described in section "(c) Signal reset"). User's Manual U17246EJ2V0UM 307 CHAPTER 7 WINDOW REFERENCE Loop dialog box This dialog box is used to perform detailed settings (loop start/stop, loop count) related to the loop information in the Signal Data Editor window. (Refer to "6. 1 Pin I/O Function".) Figure 7-75 Loop Dialog Box - Opening - Explanation of each area - Function buttons Opening Select [Edit] menu -> [Mark] -> [Loop Dialog...] in the Signal Data Editor window, or double-click the Mark area in the window. Explanation of each area (1) Start of Loop (2) End of Loop 308 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Start of Loop Select this checkbox to set the Start of Loop. (a) Endless Loop Select this radio button to set the Endless Loop. (b) Loop Count Select this radio button to set the Loop Count. Sets the count value by spin button. 0 1 to 99 (2) End of Loop Select this checkbox to set the End of Loop. Skip loop Perform loop the specified count. Function buttons OK Cancel Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. User's Manual U17246EJ2V0UM 309 CHAPTER 7 WINDOW REFERENCE Timing Chart window This window is used to display the output signals and input signals for pins in the form of a timing chart. (Refer to "6. 1 Pin I/O Function".) This window allows time measurement in main clock units. The browsed signal data can be saved as a signal data file by selecting [Simulator] menu -> [Save/Save As...]. Moreover, the saved file contents can be restored by selecting [Simulator] menu -> [Open...]. (Refer to "6. 1. 5 Signal data files (*.wvi, *.wvo)".) Figure 7-76 Timing Chart Window - Opening - Explanation of each area - Dedicated menu (Timing Chart window) - [Timing Chart] tool bar - Context menu - Operation Opening Click this button, or select [Simulator] menu -> [Timing Chart]. Explanation of each area (1) Information bar (2) Client area 310 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Information bar It can be specified whether this area is displayed or not, by selecting [View] menu -> [Information Bar]. Clock/time count from simulation start until marker A location. Clock/time count from simulation start until marker B location. Clock/time count between markers A and B. (Displayed as absolute value.) Displays the time information unit. The time information unit can be changed by selecting [Edit] menu -> [Time unit]. (2) Client area (a) Pin area (b) Maker area (c) Waveform area (a) Pin area Displays the names of the pins for which timing chart display is performed. Pin selection is performed by selecting [Edit] menu -> [Select Pin...] to open the Select Pin dialog box. (b) Maker area Displays the 2 marker headers . These markers can be moved by dragging them with the mouse over this area. Maker A Maker B (c) Waveform area Performs timing chart display for the data of the pins specified in (a) Pin area. The following color distinctions are used according to the signal. green red at the center blue at the center The HIGH and LOW signals of the pins High-impedance signals Unsampled signals The size of the buffer which stores pins is 4096 change points. If this is exceeded, the data is overwritten starting from the oldest data. When the buffer is full, the data will be overwritten by the latest data starting from the oldest data because the buffer storing the pin data is in a ring buffer format. The size of the buffer that User's Manual U17246EJ2V0UM 311 CHAPTER 7 WINDOW REFERENCE stores pin data is 4096 change points. Remark The colors in (2) Client area can be set and changed by selecting [Option] menu -> [Customize...]. Opens the Customize dialog box. Dedicated menu (Timing Chart window) (1) [Edit] menu Clear Find... Search backward Search forward Select Pin... Time unit main clock usec msec (2) [View] menu Waveform Information Bar Zoom x 1/32 x 1/16 x 1/8 x 1/4 x 1/2 x1 x2 x4 x8 x 16 x 32 Switches on/off display of (b) Maker area and (c) Waveform area. Switches on/off display of (1) Information bar. Selects the waveform data display magnification ratio from a cascade menu. Sets the magnification ratio to 1/32. Sets the magnification ratio to 1/16. Sets the magnification ratio to 1/8. Sets the magnification ratio to 1/4. Sets the magnification ratio to 1/2. Sets the magnification ratio to 1. Sets the magnification ratio to 2. Sets the magnification ratio to 4. Sets the magnification ratio to 8. Sets the magnification ratio to 16. Sets the magnification ratio to 32. Deletes all the waveform data. Opens the Search Data dialog box. Waveform data search is performed in this dialog box. Searches for the change point of the selected pin in the backward direction (toward the left). Searches for the change point of the selected pin in the forward direction (toward the right). Opens the Select Pin dialog box. The pin for which the waveform data is to be displayed is selected in this dialog box. Selects the time unit. Main clock Microsecond Millisecond 312 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (3) [Option] menu Customize... Opens the Customize dialog box. [Timing Chart] tool bar Deletes all the waveform data. Searches for the change point of the selected pin in the backward direction (toward the left). Searches for the change point of the selected pin in the forward direction (toward the right). Opens the Select Pin dialog box. The pin for which the waveform data is to be displayed is selected in this dialog box. Selects the waveform data display magnification ratio from the drop-down list. Context menu Right-clicking in one of the areas in (b) Maker area and (c) Waveform area displays a context menu. The context menus are described below by area. Clear Find Search backward Search forward Select Pin... Waveform Move MakerA Move MakerB Deletes all the waveform data. Opens the Search Data dialog box. Waveform data search is performed in this dialog box. Searches for the change point of the selected pin in the backward direction (toward the left). Searches for the change point of the selected pin in the forward direction (toward the right). Opens the Select Pin dialog box. The pin for which the waveform data is to be displayed is selected in this dialog box. Switches on/off display of (b) Maker area and (c) Waveform area. Moves marker A to the cursor location. The same action can be accomplished by pressing the Shift key + left-clicking. Moves market B to the cursor location. The same action can be accomplished by pressing the Ctrl key + left-clicking. User's Manual U17246EJ2V0UM 313 CHAPTER 7 WINDOW REFERENCE Operation (1) Pin selection (2) Display of timing chart (3) Clearing of timing chart (4) Timing measurement for timing chart (5) Data search function (6) Operation at reset (1) Pin selection To display the timing chart, it is first necessary to select the pin to be displayed. Open the Select Pin dialog box by selecting [Edit] menu -> [Select Pin...] and select the pin to be edited. Once a pin is selected, its name is displayed in (a) Pin area. (2) Display of timing chart The waveforms of the selected pins are displayed in timing chart form through execution of the user program. Remark The simulation speed can be increased by hiding the timing chart. To hide the timing chart, select [View] menu -> [Waveform] (deselect this item). (When hide is selected, (b) Maker area and (c) Waveform area are dimmed and "Display OFF" is displayed at the center of these areas. (3) Clearing of timing chart Timing chart display is cleared through CPU reset or by selecting [Edit] menu -> [Clear]. (4) Timing measurement for timing chart The timing between two points can be measured by marking 2 locations using prepared markers (A and B). The time of each marker and the time between markers are displayed in (1) Information bar. Each marker is placed by selecting [Move MarkerA] or [Move MarkerB] from the context menu. As a result, marker A and marker B are placed at the position of the mouse cursor. Moreover, the marker that is clicked last becomes the selected marker and can be subjected to key manipulation. The selected key marker is used in "(5) Data search function". Figure 7-77 Maker A, B Selected Markers Unselected Markers 314 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (5) Data search function There are two data search functions for timing charts. (a) Simple search Simple search is a function used to search change points for one pin. Select the name of the pin for which the search is to be performed in (a) Pin area and then select [Edit] menu -> [Search backward] or [Search forward]. As a result, the selected marker moves to the data position at which the change point was detected. (b) Detailed search In the case of detailed search, search using a combination of data of multiple pins can be executed. The search data is set in the Search Data dialog box displayed by selecting [Edit] menu -> [Find...]. The selected marker moves to the data position that was hit, similarly to simple search results. (6) Operation at reset If debugger or simulator reset occurs, the displayed waveforms of the timing chart are all cleared. User's Manual U17246EJ2V0UM 315 CHAPTER 7 WINDOW REFERENCE Select Pin dialog box This dialog box is used when selecting pins displayed in the Signal Data Editor window and the Timing Chart window. (Refer to "6. 1 Pin I/O Function".) The pin information set in this dialog box can be saved as a pin information file (*.pin) by clicking the - Opening - Explanation of each area - Function buttons Opening When the target window is the current window, Click this button or select [Edit] menu -> [Select Pin...]. Explanation of each area (1) Pin Name : (2) Analog : (3) Function Name : 316 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Pin Name : This area is used to specify the pin name to be connected. The connection pins can be specified either via direct input or through selection from the drop-down list. Up to 256 pins can be selected by using the scrollbar located on the right side of the pin name setting area. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (2) Analog : Select this checkbox to use the specified pin in (1) Pin Name : as an analog pin . (3) Function Name : This area is used to set a function name for the pin name on (1) Pin Name :. When a character string is input in this area, this character string is displayed as a function name in the pin name part. If nothing is specified, the pin name is displayed. Function buttons OK Validates the settings and closes this dialog box. The pin name (or display name) is applied in the Pin field of the window from where this dialog box was called up. Opens the Save As dialog box. The display contents are saved to the pin information file (*.pin). Opens the Open dialog box. Loads the pin setting information of the specified file (*.pin). Deletes the settings. Cancels the settings and closes this dialog box. Save Load Clear Cancel User's Manual U17246EJ2V0UM 317 CHAPTER 7 WINDOW REFERENCE Search Data dialog box This dialog box is used to search the signal data displayed in the Timing Chart window in detail. (Refer to "6. 1 Pin I/O Function".) Caution Analog I/O signals cannot be searched. Figure 7-79 Search Data Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Timing Chart window is the current window, Click this button or select [Edit] menu -> [Find...]. Explanation of each area (1) Pin Name : (2) Search Data : (3) Direction 318 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Pin Name : This area is used to specify the pin name to be searched. The pins can be specified either via direct input or through selection from the drop-down list. Inputting noting makes an area off-limit to data search and input in the coresponding (2) Search Data : is disabled. (2) Search Data : Selects the data from drop-down list. The data is searched for the pin to be specified in (1) Pin Name : . Up to 48 search conditions can be specified by using the scrollbar located on the right side. When multiple search conditions have been specified, the signal data that meets all these search conditions is searched. ----- ---Rising Edge Falling Edge Rise/Fall Edge High Low Hi Z Don't care Searches the rising edge of signal data. Searches the falling edge of signal data. Searches the rising/falling edge of the signal data. Searches the signal data that is HIGH. Searches the signal data that is LOW. Searches the signal data that is high impedance. (3) Direction Selects the data search direction by selecting one of the exclusive radio buttons. When the Function buttons Next Cancel Searches in the direction specified in (3) Direction. When this button is clicked again following search completion, the next data is searched. Stops the data search and closes the dialog box. User's Manual U17246EJ2V0UM 319 CHAPTER 7 WINDOW REFERENCE Standard I/O window This window is used when using the standard I/O function of the simulator. (Refer to "6. 2 Standard I/O Function".) This window allows text display of standard output data and direct input of standard input data. Display data can be saved as a text format file (*.log) by selecting [Simulator] menu -> [Save/Save As...] Figure 7-80 Standard I/O Window - Opening - Explanation of each area - Dedicated menu (Standard I/O window) - Context menu - Operation Opening Click this button or select [Simulator] menu -> [Standard I/O]. 320 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Explanation of each area (1) Standard I/O display area This area is used to display the standard output data from the simulator as text and directly input standard input data to the simulator. The maximum number of lines that can be displayed is 500. (This number can be changed in the Standard I/O Buffer Size dialog box.) If the output data exceeds the maximum number of lines, it is overwritten starting from the oldest data. Data that has been deleted through overwriting cannot be restored. Dedicated menu (Standard I/O window) (1) [Edit] menu Copy Paste Clear Select All (2) [Option] menu Simulator Option... Customize... Buffer Size... Opens the Simulator Option dialog box. Opens the Customize dialog box. Opens the Standard I/O Buffer Size dialog box. Copies the string in selected range and copies it to the clipboard. Pastes the clipboard contents. (The data is pasted at the end of the display data in (1) Standard I/O display area, and these contents are treated as standard I/O data.) Deletes all the display data. Selects all display data. Context menu Copy Paste Clear Copies the string in selected range and copies it to the clipboard. Pastes the clipboard contents. (The data is pasted at the end of the display data in (1) Standard I/O display area, and these contents are treated as standard I/O data.) Deletes all the display data. User's Manual U17246EJ2V0UM 321 CHAPTER 7 WINDOW REFERENCE Operation (1) Standard output (2) Standard input (3) Display area clear (4) Standard library usage method (1) Standard output Standard output data is displayed from the end of the display data of (1) Standard I/O display area. (2) Standard input Standard input is manipulated by directly inputting data to (1) Standard I/O display area. The input data is displayed starting from the last data. Input through pasting is also possible. (3) Display area clear Clearing of (1) Standard I/O display area is done by selecting [Edit] menu -> [Clear]. (4) Standard library usage method To use the standard library, it is necessary to set the start address (interface address) of the interface area in relation to the standard library (in the external memory area). (Refer to "6. 2. 1 Standard I/O and File I/O Usage Procedure".) 322 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Standard I/O Buffer Size dialog box This dialog box is used to specify the maximum number of lines that can be displayed in the Standard I/O window. (Refer to "6. 2 Standard I/O Function".) Figure 7-81 Standard I/O Buffer Size Dialog Box - Opening - Explanation of each area - Function buttons Opening When the Standard I/O window is the current window, select [Option] menu -> [Buffer Size...]. Explanation of each area (1) Max Line Count : The maximum number of lines that can be displayed in the Standard I/O window (buffer size) is selected from the drop-down list. Function buttons OK Cancel Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. User's Manual U17246EJ2V0UM 323 CHAPTER 7 WINDOW REFERENCE Simulator Option dialog box This dialog box is used to set the various simulator options. The [Standard Library Interface] tab is used to set/change the various information items related to the standard library interface used in the Standard I/O window. (Refer to "6. 2 Standard I/O Function".) Figure 7-82 Simulator Option Dialog Box ([Standard Library Interface] tab) - Opening - [Standard Library Interface] tab - Function buttons Opening Select [Option] menu -> [Simulator Option...] [Standard Library Interface] tab (1) Interface Address : (2) Input File Path : 324 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (1) Interface Address : This area is used to specify the start address (interface address) of the interface area (in the external memory area) for interfacing with the standard library. (2) Input File Path : This area is used to specify the file search path when using the file I/O library. Multiple paths can be specified delimited by commas. Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 325 CHAPTER 7 WINDOW REFERENCE Serial window This window is used to communicate with the serial interface provided in the CPU. (Refer to "6. 3 Serial I/O Function".) Since this window operates as the serial interface of the remote node of the CPU, transmission data from CPU turns into reception data in this window, and transmission data from this window turns into reception data in the CPU. Two types of files can be handled in this window. The transmission/reception data displayed in the top area in this window can be saved as a CSV-format text file by selecting [Simulator] menu -> [Save/Save As...]. (Refer to "6. 3. 2 Serial log data file (*.log)".) Moreover, the transmissio data created in the lower part of this window can be saved as a CSV-format text file by clicking the - Opening - Explanation of each area - Dedicated menu (Serial window) - Context menu 326 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Opening Click this button, or select [Simulator] menu -> [Serial...]. Explanation of each area (1) Serial selection area (2) Log display area (3) Serial editor area (1) Serial selection area Select the serial interface to be used. Select the serial interface to be used from the list of provided serial interfaces (dropdown list). Caution: Once selected, the serial interface cannot be changed. Displays the time information unit. The time information unit can be changed by selecting [Edit] menu -> [Time unit]. (2) Log display area Displays the transmission/reception data. The display timing is when all the bits constituting the data have been received or sent. Only data from which the start bit, stop bit, and parity bit have been deleted is displayed in this area. The data display method can be changed by selecting [View] menu-> [Numeric Representation] -> [Binary/ Hexadecimal]. Log display is cleared upon debugger or simulator reset. (a) Time Displays the time from the completion of reception/transmission of the previous data until completion of reception/transmission of the current data. The time information unit is specified by selecting [Edit] menu -> [Time unit]. (b) Send Data Displays the data sent by this window (data received by the CPU). (c) Receive Data Displays the data received by this window (data sent by the CPU). User's Manual U17246EJ2V0UM 327 CHAPTER 7 WINDOW REFERENCE (d) Status Displays the status during data reception. When an error occurs, one of the following marks is displayed. When everything is normal, nothing is displayed. P F Parity error (mismatching parity bit) Framing error (stop bit not detected) (3) Serial editor area This area is where the transmission data is created. This area can be shown or hidden by selecting [View] menu -> [Serial Editor]. The Function buttons are used for operations in this area. (a) No This is a number assigned sequentially from the beginning. It cannot be directly written. The maximum number is 9999 lines. (b) Wait Specifies the time from the completion of transmission of the immediately previous data until the start of transmission of next data. Valid during transmission using the This area is used to edit transmission data. Data can be directy input by placing the cursor in the data field and double-clicking. Data suffixed by "0x" is treated as hexadecimal data, and data suffixed by "0b" is treated as binary data. The default code is the hexadecimal code. If a bit length different from that specified in the Format (UART) dialog box or the Format (CSI) dialog box is specified, data from the lower bit is valid. One data can be written per operation. 328 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (d) Function buttons Format All Clear Load Save Send Opens the Format (UART) dialog box or the Format (CSI) dialog box. Clears all the data creation areas. Opens the Open dialog box. The contents of the specified file (*.ser) are loaded and displayed in (3) Serial editor area. Opens the Save As dialog box. The data setting contents are saved in CSV format to the specified file (*.ser). Sends one of the data selected in (3) Serial editor area. The next data becomes selected upon completion of transmission. If no data is selected, the first data is sent. Makes the data selected in (3) Serial editor area the first data, and automatically transfers from the data to the bottom of the area. The data transmission time interval is the time specified for Wait. Auto Send Dedicated menu (Serial window) (1) [Edit] menu Insert Cut Copy Paste Delete Time unit main clock usec msec Format... (2) [View] menu Serial Editor Numeric Representation Binary Hexadecimal (3) [Option] menu Customize... Opens the Customize dialog box. Selects whether (3) Serial editor area is displayed or not. Changes the display method of (2) Log display area display method. Displays binary numbers. Displays hexadecimal numbers. Inserts a new line immediately before the selected line. Cuts the selected range and saves it to the clipboard. Copies the selected range and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the selected range. Selects the time unit. Main clock Microsecond Millisecond Opens the Format (UART) dialog box or the Format (CSI) dialog box. User's Manual U17246EJ2V0UM 329 CHAPTER 7 WINDOW REFERENCE Context menu Right-clicking in one of the areas in (3) Serial editor area displays a context menu. The context menus are described below by area. Insert Cut Copy Paste Delete Inserts a new line immediately before the selected line. Cuts the selected range and saves it to the clipboard. Copies the selected range and copies it to the clipboard. Pastes the contents of the clipboard to the selected location. Deletes the selected range. 330 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Format (UART) dialog box This dialog box is used to set the serial format for the asynchronous serial interface (UART). (Refer to "6. 3 Serial I/O Function".) Figure 7-84 Format (UART) Dialog Box - Opening - Explanation of each area - Function buttons Opening When the UART serial interface is selected in the Serial window, select [Edit] menu -> [Format...], or click the Explanation of each area (1) Baudrate (2) Transfer Direction (3) Data bit length (4) Stop bit length (5) Parity (6) Repeat User's Manual U17246EJ2V0UM 331 CHAPTER 7 WINDOW REFERENCE (1) Baudrate Directly input the serial baud rate value as an integer. (Unit: bps) Remark For the selectable range, refer to the user's manual of the device that is used. (2) Transfer Direction Selects the transfer direction. MSB first LSB first Sets MSB first as the transfer direction. Sets LSB first as the transfer direction (default). (3) Data bit length Select the bit length of the transmission data from the drop-down list, or specify it through direct input. The default is 8, and a value of up to 32 can be specified. (4) Stop bit length Select the stop bit length from the drop-down list. The default is 1. (5) Parity Select the parity information (none parity/odd parity/even parity/0 parity). (6) Repeat Select this item to repeat data transfer when the Following transmission of the last data during automatic transmission, returns to the beginning of the data and performs automatic transmission. Following transmission of the last data during automatic transmission, stops transmission. Not Checked Function buttons OK Cancel Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. 332 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Format (CSI) dialog box This dialog box is used to specify the serial format for the 3-wire serial interface (CSI). (Refer to "6. 3 Serial I/O Function".) Figure 7-85 Format (CSI) Dialog Box - Opening - Explanation of each area - Function buttons - Cautions Opening When the CSI serial interface is selected in the Serial window, select [Edit] menu -> [Format...], or click the Explanation of each area (1) Master, Slave (2) Transfer Clock (3) Transfer Direction (4) Data bit length (5) Data Phase (6) Clock Phase (7) Repeat User's Manual U17246EJ2V0UM 333 CHAPTER 7 WINDOW REFERENCE (1) Master, Slave Selects the transfer mode. Master Slave Operates this window as a master. Setting of (2) Transfer Clock is required for generating the clock during communication. Operates this window as a slave (default). Communication is performed using the clock of the serial interface provided in the CPU. (2) Transfer Clock Directly input the transfer clock value (unit: kHz). Values with decimals can also be set. This item must be set when master is selected for (1) Master, Slave. Remark For the selectable range, refer to the user's manual of the device that is used. (3) Transfer Direction Selects the transfer direction. MSB first LSB first Sets MSB first as the transfer direction.(default) Sets LSB first as the transfer direction. (4) Data bit length Select the bit length of the transmission data from the drop-down list, or specify it through direct input. The default is 8, and a value of up to 32 can be specified. (5) Data Phase Select the transmission/reception timing to set the data phase. The data clock phase is set in combination with (6) Clock Phase as shown in "Table 7-28 Data Clock Phase Settings". Normal Precede Transmits/receives data at the normal 3-wire serial transmission/reception timing.(default) Transmits/receives data at a timing half a clock of the operation clock earlier than the normal 3-wire serial transmission/reception timing. (6) Clock Phase Select the transmission/reception clock waveform to set the clock phase. The data clock phase is set in combination with (5) Data Phase as shown in "Table 7-28 Data Clock Phase Settings". Normal Reverse Operates on the normal 3-wire serial clock.(Transfer starts at the falling edge of the clock.) (default) Operates on the reverse clock of the normal 3-wire serial clock. (Transfer starts at the rising edge of the clock.) 334 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Table 7-28 Data Clock Phase Settings Data Phase Setting Normal Clock Phase Setting Normal SCK SO SI input Timing Precede Normal SCK SO SI input Timing Normal Reverse SCK SO SI input Timing Precede Reverse SCK SO SI input Timing D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Data Clock Phase (7) Repeat Select this item to repeat data transfer when the Function buttons OK Cancel Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. User's Manual U17246EJ2V0UM 335 CHAPTER 7 WINDOW REFERENCE Cautions (1) Transmission/reception when 3-wire serial interface (CSI) is selected The Serial window when CSI is selected always operates in the transmission/reception mode regardless of whether "Master" or "Slave" is selected in the Format (CSI) dialog box. (a) When "Master" is selected Data is transmitted or received immediately after clicking the 336 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE 2) 3) Set the Wait time to 0 as a dummy setting in the Serial window. Click the User's Manual U17246EJ2V0UM 337 CHAPTER 7 WINDOW REFERENCE I/O Panel window This window is used to configure a dummy target system. This window is used to display and manipulate connected parts. (Refer to "6. 4 Panel Function".) A dummy target system can be constructed by making connected part settings in the I/O Panel window. The connected parts for which settings have been performed are displayed in this window, and they serve as signal interface points during simulation. Moreover, these parts can be moved to any location within the window. Information about parts that are placed in the window can be saved to a file (*.pnl) by selecting [Simulator] menu -> [Save/Save As...]. Moreover, the saved file contents can be restored by selecting [Simulator] menu -> [Open...]. Figure 7-86 I/O Panel Window - Opening - Menu bar / Tool bar - Context menu - Operation Opening Click this button, or select [Simulator] menu -> [I/O Panel...]. 338 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Menu bar / Tool bar In the [Parts] and [Figure] menus, similar operations can be performed using the buttons on the tool bar. (1) [Edit] menu (2) [View] menu (3) [Parts] menu / Tool bar (Parts) (4) [Figure] menu / Tool bar (Figure) (1) [Edit] menu Select this menu to perform basic editing actions on figure objects created using the [Figure] menu / Tool bar (Figure), as well as part objects created using the [Parts] menu / Tool bar (Parts). Undo Redo Cut Copy Paste Delete Select All Group UnGroup Bring to Front Send to Back Bring Forward Send Backward (2) [View] menu Select this menu to switch the tool bar/status bar display status in the I/O Panel window, or to show/hide various types of information in the I/O Panel window. ToolBar StatusBar Parts List... Grid Properties Switches on and off the display of two tool bars (Figure/Object). Switches on and off display of the status bar. Opens the Parts List dialog box. A list of all the figure/part objects is displayed in the I/O Panel window. Shows/hides the window grid. Opens the property dialog box of the selected figure/part object. (Refer to "Table 67 Connected Parts".) Undoes the immediately preceding operation,such as object move. Undo can restore up to 5 previous changes. Restores the status undone by the [Undo] command. Cuts the selected range and saves it to the clipboard. Copies the selected range and saves it to the clipboard. Pastes the contents of the clipboard. Deletes the selected range. Selects all the objects in the window. Groups the selected objects. Ungroups the selected objects. Brings the selected object to the front. Sends the selected object to the back. Brings the selected object one panel forward. Sends the selected object one panel backward. User's Manual U17246EJ2V0UM 339 CHAPTER 7 WINDOW REFERENCE (3) [Parts] menu / Tool bar (Parts) This menu is used to select the provided connected parts by SM+ when newly creating or placing parts in the window. When a cascade menu is selected, the cursor changes into a cross (+) and it becomes possible to create and place new parts. To create a new part, click anywhere in the window in this state and the corresponding part will be created. Then double-click the part and set the pin connection and style in the open properties dialog boxes. (Refer to "Table 6-7 Connected Parts".) Button Changes the cursor shape into a cross (+), enabling the creation of button. The same action can be accomplished by clicking this button in the tool bar. Key Matrix Changes the cursor shape into a cross (+), enabling the creation of key matrix. The same action can be accomplished by clicking this button in the tool bar. Level Gauge Changes the cursor shape into a cross (+), enabling the creation of Level gauge. The same action can be accomplished by clicking this button in the tool bar. LED Changes the cursor shape into a cross (+), enabling the creation of LED. The same action can be accomplished by clicking this button in the tool bar. 7-Segment LED Changes the cursor shape into a cross (+), enabling the creation of 7-segment LED. The same action can be accomplished by clicking this button in the tool bar. 14-Segment LED Changes the cursor shape into a cross (+), enabling the creation of 14-segment LED. The same action can be accomplished by clicking this button in the tool bar. Matrix LED Changes the cursor shape into a cross (+), enabling the creation of matrix LED. The same action can be accomplished by clicking this button in the tool bar. Buzzer Changes the cursor shape into a cross (+), enabling the creation of buzzer. The same action can be accomplished by clicking this button in the tool bar. Pull up / Pull down... Opens the Pull up/Pull down dialog box. The same action can be accomplished by clicking this button in the tool bar. (4) [Figure] menu / Tool bar (Figure) Select this menu to create and edit objects such as figures, bitmaps, and characters in the I/O Panel window. Select Changes the cursor shape into an arrow, enabling the selection of objects. The same action can be accomplished by clicking this button in the tool bar. Simulation Mode Changes the cursor shape into a hand, enabling simulation of input to connected parts. The same action can be accomplished by clicking this button in the tool bar. Line Changes the cursor shape into a cross (+), enabling the drawing of lines. The same action can be accomplished by clicking this button in the tool bar. 340 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Rectangle Changes the cursor shape into a cross (+), enabling the drawing of rectangles. The same action can be accomplished by clicking this button in the tool bar. Rounded Rectangle Changes the cursor shape into a cross (+), enabling the drawing of rectangles with rounded corners. The same action can be accomplished by clicking this button in the tool bar. Ellipse Changes the cursor shape into a cross (+), enabling the drawing of ellipses. The same action can be accomplished by clicking this button in the tool bar. Polygon Changes the cursor shape into a cross (+), enabling the drawing of polygons. The same action can be accomplished by clicking this button in the tool bar. Fan-shaped Changes the cursor shape into a cross (+), enabling the drawing of fan shapes. The same action can be accomplished by clicking this button in the tool bar. Text Changes the cursor shape into a cross (+), enabling the drawing of text. The same action can be accomplished by clicking this button in the tool bar. Paste Bitmap... Color of Line... Opens the Open dialog box. This dialog box is used to paste the selected bitmap file in the I/O Panel window. Opens the Edit Colors dialog box. The color of the lines of the selected object can be changed to the selected color in this dialog box. The same action can be accomplished by clicking this button in the tool bar. Color of Fill... Opens the Edit Colors dialog box. The color used for the selected object can be changed to the selected color in this dialog box. The same action can be accomplished by clicking this button in the tool bar. Font... Style of Line Opens the Font dialog box (Simulator Block). The font of the selected object can be changed to the selected font in this dialog box. Selects the line style from a cascade menu. The lines of the selected object are changed. The same action can be accomplished by clicking this button in the tool bar. 16pt 12pt 8pt 4pt 2pt 1pt No line Dotted Line Style Sets the line thickness to 16 pt. Sets the line thickness to 12 pt. Sets the line thickness to 8 pt. Sets the line thickness to 4 pt. Sets the line thickness to 2 pt. Sets the line thickness to 1 pt. Does not draw lines. Selects the dotted line style from a cascade menu. The lines of the selected object are changed. The same action can be accomplished by clicking this button in the tool bar. User's Manual U17246EJ2V0UM 341 CHAPTER 7 WINDOW REFERENCE Solid Line Dash Line Dotted Line DashDot Line DashDotDot Line Draw solid lines. Draw dashed lines. Draw dotted lines. Draw DashDot lines. Draw DashDotDot lines. Context menu This menu is displayed by right-clicking in the I/O Panel window in the edit mode (when [Figure] menu -> [Select] is selected). Copy Paste Delete Group Group UnGroup Order Bring to Front Send to Back Bring Forward Send Backward Properties Copies the selected objects. Pastes the contents of the clipboard. Deletes the selected objects. Selects from a cascade menu. Groups the selected objects. Ungroups the selected objects. Selects from a cascade menu. Brings the selected object to the front. Sends the selected object to the back. Brings the selected object one panel forward. Sends the selected object one panel backward. Opens the property dialog box of the selected figure/part object. (Refer to "Table 67 Connected Parts".) Operation (1) Drawing figure objects (2) Changing the figure object style (3) Inputting text (4) Pasting a bitmap (5) Creating a new part object (6) Edit mode (7) Selecting objects (8) Moving objects (9) Changing object size (10) Cut/Copy/Paste/Delete/Group/UnGroup an object (11) Changing object sequence (Bring to Front/Send to Back/Bring Forward/Send Backward) (12) List display of connected parts/figure objects (13) Grid display 342 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (14) Object properties display (15) Inputting connected parts (1) Drawing figure objects Drawing a line 1) Select [Figure] menu -> [Line] or click the corresponding button on the tool bar. -> The mouse cursor changes to a cross (+) shape and line drawing becomes possible. 2) Drag the cursor from the line start position to the end position. -> The line start position and the line end position are connected by a straight line. (The line thickness and shape are the default settings.) Drawing a rectangle/rounded rectangle/fan shape 1) Select [Figure] menu -> [Rectangle/Rounded Rectangle/Ellipse/Fan-shaped] or click the corresponding button on the tool bar. -> The mouse cursor changes to a cross (+) shape and each drawings becomes possible. 2) Drag the mouse cursor from the top left corner to the bottom right corner of the drawing area (rectangular area). -> The corresponding figure is displayed in the drawing area, with the mouse position forming the lower right corner. 3) Drop the figure to fix its size. -> Rectangles are drawn in the same size as the rectangular area, and other figure shapes are drawn in a size that fits in the rectangular area. (The line thickness and shape are the default settings.) Drawing a polygon 1) Select [Figure] menu -> [Polygon] or click the corresponding button on the tool bar. -> The mouse cursor changes to a cross (+) shape and polygon drawing becomes possible. 2) Click at each position marking an apex of the polygon. -> The apexes are linked by a straight line in the order in which they were clicked. 3) Drawing of the polygon is completed by double-clicking. -> The line thickness and shape are the default settings. (2) Changing the figure object style Changing the figure object style can be accomplished with any one of the following methods. - Select the corresponding figure, and then on the [Style] tab in the dialog box opened by right-clicking, change the style. - Select [Figure] menu -> [Color of Line /Color of Fill /Style of Line/Dotted Line Style] (or click the corresponding button on the tool bar), and change the style. User's Manual U17246EJ2V0UM 343 CHAPTER 7 WINDOW REFERENCE (3) Inputting text 1) Select [Figure] menu -> [Text] or click the corresponding button on the tool bar. -> The mouse cursor changes to a cross (+) shape. 2) Drag the mouse cursor from the top left corner of the character drawing area (rectangular area) to the lower right corner. -> This rectangular area serves as the character drawing area. 3) Click in the character drawing area. -> The cursor is displayed and character input becomes possible. (4) Pasting a bitmap 1) Select the [Figure] menu -> [Paste Bitmap] -> Opens the Open dialog box. 2) Select the bitmap file (*.bmp) to be pasted. -> The corresponding bitmap file is pasted in the default position in the I/O Panel window. (5) Creating a new part object 1) Select the part to be created from [Parts] menu or the tool bar. -> The mouse cursor changes to a cross (+) shape. 2) Click any location. -> The corresponding part is created and placed with the clicked location as the top left corner (default size). (6) Edit mode Editing in the I/O Panel window is performed in the edit mode. The mode can be change to the edit mode using the following methods. - Select [Figure] menu -> [Select]. - Click the corresponding button on the tool bar. - When [Figure] menu -> [Simulation mode] is not selected, click any location in the I/O Panel window. - Select [Edit] menu -> [Select All]. (7) Selecting objects The selected types and methods are indicated below. The selected object or objects are displayed surrounded by a tracker indicating their selected status. - Single selection -> Click the object to be selected. - Multiple selections -> Click the objects to be selected while pressing the Shift key. - Range selection -> Drag from the top left corner of the area including the object to be selected, and drop at the lower right corner. - Select all -> Select [Edit] menu-> [Select All]. 344 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (8) Moving objects 1) Select the object to be moved (multiple selections possible). -> A tracker indicating the selected status is displayed around the corresponding object. 2) Drag the object and drop it at the move destination. -> The corresponding object is moved. (9) Changing object size 1) Select the object whose size is to be changed. -> A tracker indicating the selected status is displayed around the corresponding object. 2) Click the tracker. -> The mouse cursor changes to an arrow shape (->) indicating the direction in which the size can be changed. 3) Drag. -> The size of the object changes. (10) Cut/Copy/Paste/Delete/Group/UnGroup an object After selecting the desired object, select the corresponding item from (1) [Edit] menu. (11) Changing object sequence (Bring to Front/Send to Back/Bring Forward/Send Backward) After selecting the target object, select the corresponding item from (1) [Edit] menu. (12) List display of connected parts/figure objects Objects created in the I/O Panel window can be displayed as a list by selecting [View] menu -> [Parts List], in addition to display in the I/O Panel window. (13) Grid display A grid is displayed in the I/O Panel window by selecting [View] menu -> [Grid]. (14) Object properties display The properties dialog box for the corresponding object can be opened using one of the following methods. - Double-click the corresponding object. - Right-click the corresponding object and select [Properties...]. - Select the corresponding object and then select [View] menu -> [Properties...]. (15) Inputting connected parts By selecting [Figure] menu -> [Simulation Mode], the mouse cursor changes to a hand shape and input to connected parts becomes possible. For input details, refer to the properties dialog box of each connected part. (Refer to "Table 6-7 Connected Parts".) User's Manual U17246EJ2V0UM 345 CHAPTER 7 WINDOW REFERENCE Parts Button Properties This property dialog box is used to set or change the pin connection information of buttons, which are one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) Input to the simulator can be done from pin-connected buttons. There are two types of button display styles, figure and bitmap. These styles can be changed on the [Style] tab (standard). Figure 7-87 Parts Button Properties ([Button Connection] tab) Figure 7-88 Parts Button Properties ([Style] tab (Standard)) 346 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE - Opening - [Button Connection] tab - [Style] tab (standard) - Function buttons - Display examples and operation Opening Double-click the corresponding connected parts (Button) in the I/O Panel window, or select the corresponding parts (Button) and select [View] menu -> [Properties...]. [Button Connection] tab (1) Label : (2) Pin Name : (3) Active Label : (4) Type : (5) Group Name : (6) Hold Time : (1) Label : This area is used to specify the part name. The part name input here is displayed on the button. Moreover, it is also displayed in the Parts List dialog box as the label. (2) Pin Name : This area is used to specify the pin name to be connected. The connection pins can be specified either via direct input or through selection from the drop-down list. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (3) Active Label : The active state of the button is selected with a radio button, as follows. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) (4) Type : Button types are selected using radio buttons, as follows. Push Toggle Group Makes the button a Push button. The (6) Hold Time : item must be specified. Makes the button a Toggle button. Makes the button a Group button. The (5) Group Name : item must be specified. User's Manual U17246EJ2V0UM 347 CHAPTER 7 WINDOW REFERENCE (5) Group Name : This area is used to input the button's group name. Input to this area is possible only when "Group" has been selected in (4) Type :. (6) Hold Time : Specify the time (hold time) for which the input value is to be held (default : 0.5msec). The settable range is from 0.001 to 999 (msec). Input to this area is possible only when "Push" has been selected in (4) Type :. [Style] tab (standard) This [Style] tab (standard) is used in common as the [Style] tab for the Parts Button Properties, the Parts Key Properties, the Parts Led Properties, the Parts Matrix Led Properties, and the Parts Buzzer Properties. (1) Figure (2) Bitmap (3) Preview (1) Figure Check this button to select "Figure" as the part display style. (a) Shape : Select the figure shape. Two shapes can be selected: rectangle and ellipse. (b) Shadow : Cannot be selected. (c) Line : Specifies and changes settings related to figure line, as follows. Thickness : Specifies the line thickness. Specification is made either using a spin button or through direct input. A value from 1 to 100 can be specified. Specifies the color of the line during active display. The Color Selection Palette is displayed by clicking the pull-down button. Specifies the color of the line during inactive display. The Color Selection Palette is displayed by clicking the pull-down button. Active : Inactive : (d) Fill up : Specifies and changes settings related to figure filling, as follows. Active : Inactive : Specifies the fill color during active display. The Color Selection Palette is displayed by clicking the pull-down button. Specifies the fill color during inactive display. The Color Selection Palette is displayed by clicking the pull-down button. 348 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (2) Bitmap Check this radio button to select bitmap as the display style for parts. (a) Bitmap selection list The selectable bitmaps are displayed. (b) Select the bitmap to be deleted from (a) Bitmap selection list, and then click this button to delete the bitmap from the list. (3) Preview Previews the view file selected in (1) Figure and (2) Bitmap. Active : Inactive : Preview in active status Preview in inactive status Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 349 CHAPTER 7 WINDOW REFERENCE Display examples and operation By clicking the displayed button, data can be input to the pin connected to the button. The input format differs depending on the button type (push, toggle, group). Figure 7-89 Parts Display Example (Button) (1) Push button Cicking this button causes the active value to be loaded to the connected pin. The active value is held during the hold time, after which it changes to the original value. (2) Toggle button Clicking this button loads the active value to the connected pin. The active value is held during the hold time, after which it changes to the original value. (3) Group button Clicking this button loads the active value to the connected pin. The value of the Group button having the same group name returns to the original value. 350 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Parts Key Properties This property dialog box is used to set or change the pin connection information of a key matrix, which is one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) Input to the simulator can be done from pin-connected keys. A key matrix consisting of input pins and output pins of up to 16 x 16 can be set. Either figure or bitmap can be selected as the key matrix display style. These styles can be changed on the [Style] tab (standard). Caution When connecting a key matrix to pins, also perform the Pull up/Pull down settings for the connection pins. When a key is pressed, the output value of the output pin connected to that key is input to the input pin connected to that key. The value when the key is not pressed is the value specified in the Pull up/Pull down dialog box. (If the pull up/pull down settings are not performed, the value when the key is not pressed is treated as 0 in the simulator.) Figure 7-90 Parts Key Properties ([Key Matrix Connection] tab) - Opening - [Key Matrix Connection] tab - [Style] tab (standard) - Function buttons - Display examples and operation User's Manual U17246EJ2V0UM 351 CHAPTER 7 WINDOW REFERENCE Opening Double-click the corresponding connected parts (Key Matrix) in the I/O Panel window, or click the corresponding parts (Key Matrix) and select [View] menu -> [Properties...]. [Key Matrix Connection] tab (1) Label : (2) Connection pin setting area (In0 In1 In2.... Out0 Out1 Out2.....) (3) Key Label setting area (N00 N01 N02...) (4) Hold Time : (1) Label : This area is used to specify the part name. The part name input here is also displayed in the Parts List dialog box as the label. (2) Connection pin setting area (In0 In1 In2.... Out0 Out1 Out2.....) This area is used to specify the pin name to be connected (input pins and output pins). The connection pins can be specified either via direct input or through selection from the drop-down list. Int0 - Int15 Out0 - Out15 Specify output pins. Specify input pins. This area can be used to set 16 x 16 pins using the scrollbar in combination with (3) Key Label setting area (N00 N01 N02...). Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (3) Key Label setting area (N00 N01 N02...) This area is where the text strings displayed on the keys of the key matrix are specified. Text strings of any length can be specified. The default description string (N number) is not displayed on the keys. This area can be used to set 16 x 16 pins using the scrollbar in combination with (2) Connection pin setting area (In0 In1 In2.... Out0 Out1 Out2.....). (4) Hold Time : Specify the time (hold time) for which the input value is to be held (default : 0.5msec). The settable range is from 0.001 to 999 (msec). Moreover, when multiple keys for input to the same input pin are pressed during the hold time, only the key that was clicked last is valid. 352 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. Display examples and operation (1) Inputting multiple keys simultaneously (2) Locking the key input value (1) Inputting multiple keys simultaneously To enter two keys, simultaneously press the key to be input and right-click the mouse to enter the wait status. Then, click the other key. This releases the wait status and enables simultaneous input of both keys. Multiple keys can be simultaneously input by setting the wait status for multiple keys, but if input is to be performed to the same input pin, the key that was input last is valid. (2) Locking the key input value To enter two keys, simultaneously press the key to be input and right-click the mouse to enter the wait status. Then, click the other key. This releases the wait status and enables simultaneous input of both keys. Multiple keys can be simultaneously input by setting the wait status for multiple keys, but if input is to be performed to the same input pin, the key that was input last is valid. Figure 7-91 Parts Display Example (Key Matrix) User's Manual U17246EJ2V0UM 353 CHAPTER 7 WINDOW REFERENCE Parts Level Gauge Properties This property dialog box is used to set or change the pin connection information of level gauge, which are one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) Input to the simulator can be done from pin-connected level gauge. However, the connection pin must be an analog input pin. There are two types of level gauge display styles, slide and dial. These styles can be changed on the [Style] tab. Figure 7-92 Parts Level Gauge Properties ([Level Gauge Connection] tab) Figure 7-93 Parts Level Gauge Properties ([Style] tab) 354 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE - Opening - [Level Gauge Connection] tab - [Style] tab (Level Gauge Properties-dedicated) - Function buttons - Display examples and operation Opening Double-click the corresponding connected parts (Level Gauge) in the I/O Panel window, or click the corresponding parts (Level Gauge) and select [View] menu -> [Properties...]. [Level Gauge Connection] tab (1) Label : (2) Pin Name : (3) Maximum input : (1) Label : This area is used to specify the part name. The part name input here is also displayed in the Parts List dialog box as the label. (2) Pin Name : This area is used to specify the pin name to be connected. The connection pins can be specified either via direct input or through selection from the drop-down list. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (3) Maximum input : This area is used to set the maximum level gauge input value (default : 5000mV). The settable range is from 0 to 65535 . The operation range of the level gauge displayed in the I/O Panel window is determined by this specified value. User's Manual U17246EJ2V0UM 355 CHAPTER 7 WINDOW REFERENCE [Style] tab (Level Gauge Properties-dedicated) (1) Slide (2) Dial (3) Preview (1) Slide To select the slide-type level gauge, check this radio button. (a) Form : Select the slide direction (vertical or horizontal) from the drop-down list. (b) Color This area is used to specify or change the slide color. Color Selection Palette is displayed by clicking the pull-down button. (2) Dial To select the dial-type level gauge, check this radio button. (a) Color of mark : This area is used to specify or change the color of the mark indicating the operating point. Color Selection Palette is displayed by clicking the pull-down button. (b) Bitmap selection list Displays the dial-type level gauge bitmaps that can currently be selected. (c) These buttons are used to make additions/deletions to/from the bitmap selection list. (3) Preview Displays the selected part style in preview form. The status style is previewed both when the part is active and when it is inactive. Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. 356 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Display examples and operation Analog input from the level gauge is performed through manipulation of the displayed slider or dial. The value specified in (3) Maximum input : is the maximum value that can be input. Input is enabled by selecting [Figure] menu -> [Simulation Mode]. Figure 7-94 Parts Display Example (Level Gauge) (1) Slide-type level gauge The displayed analog value changes as the slider button is moved by dragging it with the mouse. When this analog value has become the value that is to be input, release the button. As a result, the displayed analog value is input. The button can also be moved by clicking the desired location on the slider. (2) Dial-type level gauge The displayed analog value changes as the operating point (red circle) on the dial is moved by dragging it with the mouse. When this analog value has become the value that is to be input, release the operating point. As a result, the displayed analog value is input. The operating point can also be moved by clicking the desired location on the dial. User's Manual U17246EJ2V0UM 357 CHAPTER 7 WINDOW REFERENCE Parts Led Properties This property dialog box is used to set or change the pin connection information of LED, which are one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) A pin-connected LED displays the information output from the simulator through lit/unlit display. There are two types of LED display styles, figure and bitmap. These styles can be changed on the [Style] tab (standard). Figure 7-95 Parts Led Properties ([LED Connection] tab) - Opening - [LED Connection] tab - [Style] tab (standard) - Function buttons - Display examples and operation Opening Double-click the corresponding connected parts (LED) in the I/O Panel window, or click the corresponding parts (LED) and select [View] menu -> [Properties...]. 358 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE [LED Connection] tab (1) Label : (2) Pin Name : (3) Active Level : (1) Label : This area is used to specify the part name. The part name input here is also displayed in the Parts List dialog box as the label. (2) Pin Name : This area is used to specify the pin name to be connected (output pin) . The connection pins can be specified either via direct input or through selection from the drop-down list. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (3) Active Level : The active state is selected with a radio button, as follows. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. Display examples and operation The output status (active/inactive) of the connected pins is displayed in real time using two types of bitmaps or figures. Figure 7-96 Parts Display Example (LED) When active When inactive User's Manual U17246EJ2V0UM 359 CHAPTER 7 WINDOW REFERENCE Parts Segment LED Properties This property dialog box is used to set or change the pin connection information of 7-segment LED and 14-segment LED, which are one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) A LED connected to pins displays the information output from the simulator. The segment LED display styles can be changed on the [Style] tab. Figure 7-97 Parts Segment LED Properties [SegmentLED Connection] Tab Figure 7-98 Parts Segment LED Properties [Style] Tab 360 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE - Opening - [SegmentLED Connection] Tab - [Style] tab (Segment LED-dedicated) - Function buttons - Display examples and operation Opening Double-click the corresponding connected parts (7-segment LED/14-segment LED) in the I/O Panel window, or click the corresponding parts (7-segment LED/14-segment LED) and select [View] menu -> [Properties...]. [SegmentLED Connection] Tab (1) Label : (2) Grid type : (3) Segment Signal (Segment signal setting area) (4) Digit Signal (Digit/Grid signal setting area) (1) Label : This area is used to specify the part name. The part name input here is also displayed in the Parts List dialog box as the label. (2) Grid type : Select the grid signal allocation method from the following. As a result of the selection, the setting in (4) Digit Signal (Digit/Grid signal setting area) changes. Digit Connects each segment LED to 1 grid pin. Digit signal settings are performed in (4) Digit Signal (Digit/Grid signal setting area). 16 digits can be specified for the digit signal. A segment LED of up to 16 digits can be created with 1 segment LED part. Cannot be selected. Customize (3) Segment Signal (Segment signal setting area) This area is used to specify the pins (output pins) to be connected to the segment signals of the 7/14-segment LED, as well as their active level. (a) Pin Name : The connection pins can be specified either via direct input or through selection from the drop-down list. The number of segment pins to be connected is 8 in the case of a 7-segment LED, and 15 in the case of a 14segment LED. Connection to all the segment pins is possible by using the scroll bar on the right side. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. User's Manual U17246EJ2V0UM 361 CHAPTER 7 WINDOW REFERENCE (b) Figure This area displays the bitmap of the 7/14 segment LED at the top left. corresponding location is indicated. (c) Active Label : When (a) Pin Name : is input, the The active status of the segment signals of 7/14-segment LED can be selected with a radio button, as follows. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) (4) Digit Signal (Digit/Grid signal setting area) This area is used to specify 7/14 segment LED digits, grid signal connection pins (output pins), and their active level. The connection method changes as follows according to what is specified for (2) Grid type :. When [Digit] selected Perform digit signal setting. The maximum number of digit pins that can be connected is 16. Connection to all the digit pins can be done by using the scroll bar on the right side of the area. Cannot be selected. When [Customize] selected (a) Pin Name : The connection pins can be specified either via direct input or through selection from the drop-down list. As the setting signal, specify the connection pins in a series from the lowermost digit. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (b) Active Label : The active status of the 7/14-segment LED's digit/grid signal can be selected with a radio button. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) 362 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE [Style] tab (Segment LED-dedicated) (1) Full up LED (2) Frame Line of LED (1) Full up LED This area is used to set and change related to the filling of each cell of the object are performed. (a) Active Color : Specify the fill color during active display. Color Selection Palette is displayed by clicking the pull-down button. (b) Inactive Color : Specify the fill color during inactive display. Color Selection Palette is displayed by clicking the pull-down button. (2) Frame Line of LED This area is used to set and change related to the frame of each cell of the object are performed. (a) Color of Line : Specifies and changes the line color. Color Selection Palette is displayed by clicking the pull-down button. (b) Dotted/Solid Line : Specifies and changes the line shape (dotted/solid). The desired line shape can be selected from the drop-down list. The line shape can be specified only when the line thickness is "1" in (c) Thickness of Line :. (c) Thickness of Line : Specifies and changes the line thickness. The desired line thickness can be specified either via direct input or through selection from the spin button. A value in the range of 1 to 100 (decimal) can be specified. Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 363 CHAPTER 7 WINDOW REFERENCE Display examples and operation As the results of 1 simulation, the output information of the connection pins is received and display is performed accordingly. When both the digit/grid signals and segment signals are active output, the segment LED of the corresponding digit/grid light. Figure 7-99 Parts Display Example (7-segment LED) 364 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Parts Matrix Led Properties This property dialog box is used to set or change the pin connection information of Matrix LED, which are one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) A pin-connected Matrix LED displays the information output from the simulator through lit/unlit display. There are two types of matrix LED display styles, figure and bitmap. These styles can be changed on the [Style] tab (standard). Figure 7-100 Parts Matrix Led Properties ([Matrix LED Connection] Tab) - Opening - [Matrix LED Connection] Tab - [Style] tab (standard) - Function buttons - Display examples and operation Opening Double-click the corresponding connected parts (Matrix LED) in the I/O Panel window, or click the corresponding parts (Matrix LED) and select [View] menu -> [Properties...]. User's Manual U17246EJ2V0UM 365 CHAPTER 7 WINDOW REFERENCE [Matrix LED Connection] Tab (1) Label : (2) Row Signal (Row direction signals setting area) (3) Column Signal (Column direction signals setting area) (1) Label : This area is used to specify the part name. The part name input here is also displayed in the Parts List dialog box as the label. (2) Row Signal (Row direction signals setting area) This area is used to specify the output pins connected to the matrix LED row direction signals and their active level. (a) Pin Name : The connection pins can be specified either via direct input or through selection from the drop-down list. A maximum of 16 pins can be connected. Connection to all the row direction signals can be done by using the scrollbar located on the right side of the pin name input area. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (b) Active Level : The active status of the Matrix LED's row direction signal can be selected with a radio button. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) (3) Column Signal (Column direction signals setting area) This area is used to specify the output pins connected to the matrix LED column direction signals and their active level. (a) Pin Name : The connection pins can be specified either via direct input or through selection from the drop-down list. A maximum of 16 pins can be connected. Connection to all the column direction signals can be done by using the scrollbar located on the right side of the pin name input area. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. 366 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE (b) Active Level : The active status of the Matrix LED's column direction signal can be selected with a radio button. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. Display examples and operation As the results of 1 simulation, the output information of the connection pins is received and display is performed accordingly. When the matrix intersection of a row pin and column pin is active, the corresponding LED lights. Figure 7-101 Parts Display Example (Matrix LED) User's Manual U17246EJ2V0UM 367 CHAPTER 7 WINDOW REFERENCE Parts Buzzer Properties This property dialog box is used to set or change the pin connection information of a buzzer, which is one of the connection parts in the I/O Panel window. (Refer to "6. 4 Panel Function".) The pin-connected buzzer displays the information output from the connected pins as a bitmap and buzzer sound. The buzzer output can be checked as "sound" and "display". There are two types of buzzer display styles, figure and bitmap. These styles can be changed on the [Style] tab (standard). Figure 7-102 Parts Buzzer Properties [Buzzer Connection] Tab - Opening - [Buzzer Connection] Tab - [Style] tab (standard) - Function buttons - Display examples and operation Opening Double-click the corresponding connected parts (Buzzer) in the I/O Panel window, or click the corresponding parts (Buzzer) and select [View] menu -> [Properties...]. 368 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE [Buzzer Connection] Tab (1) Label : (2) Pin Name : (3) Active Level : (4) Output Form : (1) Label : This area is used to specify the part name. The part name input here is also displayed in the Parts List dialog box as the label. (2) Pin Name : This area is used to specify the output pin name to be connected. The connection pins can be specified either via direct input or through selection from the drop-down list. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (3) Active Level : The active state is selected with a radio button, as follows. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) (4) Output Form : The output form is specified with a check box, as follows. Sound When this checkbox is checked, the output from the pins is represented as a sound. Caution :The operation of the sound output function requires a soundboard and a speaker. When this checkbox is checked, the output from the pins is represented as a bitmap. Display Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 369 CHAPTER 7 WINDOW REFERENCE Display examples and operation The active level output of the connected pins can be expressed as a bitmap or sound (or both). In the case of bitmap display, the following bitmaps are displayed according to the pin's output value (active/ inactive). In the case of buzzer sound output, a buzzer sound is emitted when the connected pin outputs an active level value (when the status changes from inactive to active). Figure 7-103 Parts Display Example (Buzzer) When active When inactive 370 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Pull up/Pull down dialog box This dialog box is used to set or change the pin connection information of the pull up/pull down resistors, which are one of the connection parts of the I/O Panel window. (Refer to "6. 4 Panel Function".) The setting method for these connection parts differs from those for other parts. The connection information of all the pins is managed as a group in this dialog box. Figure 7-104 Pull up/Pull down dialog box - Opening - Explanation of each area - Function buttons Opening Click this button, or when the I/O Panel window is the current window, select [Parts] menu -> [Pull up/Pull down...]. Explanation of each area (1) Pin Name (2) Pull Up/Pull Down (3) Buttons User's Manual U17246EJ2V0UM 371 CHAPTER 7 WINDOW REFERENCE (1) Pin Name Displays the names of the pins that can be connected to pull-up/pull-down resistors. (2) Pull Up/Pull Down Displays the connected status of the pins. Pull Up Pull Down Pull up resistor connected status Pull down resistor connected status Pull up/Pull down resistor unconnected status (3) Buttons Pull Up Pull Down Disconnect Connects the pins selected in (1) Pin Name to pull up resistors. When connection is completed, "Pull Up" is displayed in (2) Pull Up/Pull Down. Connects the pins selected in (1) Pin Name to pull down resistors. When connection is completed, "Pull Down" is displayed in (2) Pull Up/Pull Down. Cancels the connected status of the pins selected in (1) Pin Name. When connection is completed, "-" is displayed in (2) Pull Up/Pull Down. Function buttons OK Cancel Help Validates the settings and closes this dialog box. Changes are reflected to the simulator. Cancels the settings and closes this dialog box. Changes are not reflected to the simulator. Displays this dialog box online help files. 372 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Object Properties This page is used to set or change the connection information fed to the pins of figure, text, or bitmap objects of the I/O Panel window. (Refer to "6. 4 Panel Function".) Show/hide can be switched for each pin-connected object by the output status of the connected pins. The default status of each signal is active HIGH. Display styles can be changed on the [Style] tab. Figure 7-105 Object Properties ([Object Connection] Tab) Figure 7-106 Object Properties ([Style] Tab) User's Manual U17246EJ2V0UM 373 CHAPTER 7 WINDOW REFERENCE - Opening - [Object Connection] Tab - [Style] Tab (Object Properties-dedicated) - Function buttons Opening Double-click the desired figure/character/bitmap in the I/O Panel window, or click the desired figure/character/ bitmap, and then select [View] menu -> [Properties...]. [Object Connection] Tab (1) Pin Name : (2) Active Level : (1) Pin Name : Select the method for connecting objects and output pins by clicking the corresponding radio buttons, and specify the output pin name. As a result of the connection, figure display is switched by the ON/OFF status of the connected output pin. Remark For the pin names that can be specified, refer to the user's manual of the device that is used. (a) No Connection The object and pin are not connected. Objects not connected to pins are always in the displayed status. (b) Static Connection : Connects the figure to 1 output pin. The connection pin can be specified in Pin Name: either via direct input or through selection from the dropdown list. During simulation, the object is displayed when the specified output signal data is active. (c) Dynamic Connection : Connects the figure to 2 output pins. The connection pin can be specified in Pin Name1: and Pin Name2: either via direct input or through selection from the drop-down list. During simulation, the object is displayed when the specified output signal 1 data and the specified output signal 2 data are both active. (2) Active Level : The common active status of each output signal can be selected from the radio buttons. LOW HIGH Sets the active level to LOW. Sets the active level to HIGH. (default) 374 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE [Style] Tab (Object Properties-dedicated) (1) Fill Up (2) Line (1) Fill Up Specifies and changes settings related to each object filling, as follows. The area to be filled differs according to the object. Line Rectangle,Ellipse, Rounded Rectangle Polygon Text Bitmap Not applicable Inside area enclosed by contour lines Inside area enclosed by lines linking apexes Inside text box Inside figure drawing area Caution : At this time, the bitmap that was displayed becomes invisible. (a) Color : The Color Selection Palette is displayed by clicking the pull-down button. Figure 7-107 Color Selection Palette User's Manual U17246EJ2V0UM 375 CHAPTER 7 WINDOW REFERENCE (2) Line This area is used to perform settings and changes related to the lines of objects. The definition of line for each type of object is provided below. Line Rectangle,Ellipse, Rounded Rectangle Polygon Text Bitmap (a) Color : Specifies and changes the line color. The Color Selection Palette is displayed by clicking the pull-down button. (b) Dotted/Solid : Specify or change line shapes (dotted line/solid line). The desired line shape can be selected from the drop-down list. Only specifiable when "1' is specified for (c) Thickness of Line :. (c) Thickness of Line : All areas of the object Contour line of the figure Lines that link the apexes of the polygon Contour lines of the text box Contour lines of figure drawing area Specifies and changes the line thickness. The desired line thickness can be specified either via direct input or through selection from the spin button. A value in the range of 1 to 100 (decimal) can be specified. Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Cannot be selected. Displays this dialog box online help files. 376 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Parts List dialog box This dialog box displays all the figure objects created in the I/O Panel window as well as the pin connection status of part objects. (Refer to "6. 4 Panel Function".) Selectable objects in the I/O Panel window are highlighted. To change the setting contents for pin connections for each object, open this dialog box by double-clicking the desired object and select the properties dialog box. Figure 7-108 Parts List dialog box - Opening - Explanation of each area - Function buttons Opening When the I/O Panel window is the current window, select [View] menu -> [Parts List...]. Explanation of each area (1) Label (2) Parts (3) Pin Name (4) Active Level User's Manual U17246EJ2V0UM 377 CHAPTER 7 WINDOW REFERENCE (1) Label Displays the label (name) attached to the object. Nothing is displayed for objects that do not have a label. (2) Parts Displays the part category. rectangle polygon text bitmap button key level gauge led 7segment led 14segment led matrix led buzzer Straight line, rectangle, ellipse, rounded rectangle, fan shape Polygon Text Bitmap Push button, pull button, group button Key matrix Level gauge LED 7-segment LED 14-segment LED Matrix LED Buzzer (3) Pin Name Displays the pins connected to parts. "-" is displayed for parts that are connected to multiple pins, and a blank is displayed for parts that are unconnected. (4) Active Level Displays the active value currently set for the part. "-" is displayed for parts that are connected to multiple pins, and a blank is displayed for parts that are unconnected. Function buttons Close Closes the this dialog box. 378 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Entry Bitmap dialog box This dialog box is used to add bitmaps on the [Style] tab of the Properties dialog box of connected parts. (Refer to "6. 4 Panel Function".) Figure 7-109 Entry Bitmap Dialog Box - Opening - Explanation of each area - Function buttons Opening Click the Explanation of each area (1) Active Bitmap : (2) Inactive Bitmap : (1) Active Bitmap : Specify the bitmap file (*.bmp) to be displayed when the dialog box is active. The bitmap file is specified either through file selection using the <...> button located to the right (Browse button), or through direct input. (2) Inactive Bitmap : Specify the bitmap file (*.bmp) to be displayed when the dialog box is inactive. The bitmap file is specified either through file selection using the <...> button located to the right (Browse button), or through direct input. Function buttons OK Cancel Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. User's Manual U17246EJ2V0UM 379 CHAPTER 7 WINDOW REFERENCE Customize dialog box This dialog box is used to set or change various information such as window color and fonts. These settings or changes are valid for simulator windows. (Refer to "Table 7-1 Window List".) Figure 7-110 Customize Dialog Box ([Color] Tab) Figure 7-111 Customize Dialog Box ([Font] Tab) - Opening - [Color] Tab - [Font] Tab - Function buttons 380 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Opening When the window of simulator block is opened, select [Option] menu -> [Customize...]. [Color] Tab Set and change the color of each part in the window. (1) List : The parts for which color change is possible are displayed in list form. (2) Color : The currently set color of the part is displayed when that part is selected from the list. (3) [Font] Tab Set and change the text font of each part in the window. (1) List : The parts for which font change is possible are displayed in list form. (2) Font : The current font name of the part is displayed, when that part is selected from the list. (3) Size : The current font size of the part is displayed, when that part is selected from the list. (4) Function buttons OK Cancel Apply Help Validates the settings and closes this dialog box. Cancels the settings and closes this dialog box. Leaves this dialog box open and applies the setting. Displays this dialog box online help files. User's Manual U17246EJ2V0UM 381 CHAPTER 7 WINDOW REFERENCE Edit Colors dialog box This dialog box is used to specify the color of figures, lines, etc. This dialog box is created using the common dialog box. Figure 7-112 Edit Colors Dialog Box 382 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Font dialog box (Simulator Block) This dialog box is used to select the font of the text to be displayed. This dialog box is created using the common dialog box. Figure 7-113 Font Dialog Box User's Manual U17246EJ2V0UM 383 CHAPTER 7 WINDOW REFERENCE Open dialog box This dialog box is used to specify/select the file to be manipulated. This dialog box is created using the common dialog box. Figure 7-114 Open Dialog Box 384 User's Manual U17246EJ2V0UM CHAPTER 7 WINDOW REFERENCE Save As dialog box This dialog box is used to specify/select the file to be saved. This dialog box is created using the common dialog box. Figure 7-115 Save As Dialog Box User's Manual U17246EJ2V0UM 385 CHAPTER 8 COMMAND REFERENCE CHAPTER 8 COMMAND REFERENCE This chapter explains the details of the command functions of the SM+. - Command Line Rules - Command List - List of Variables - List of Packages - Key Bind - Expansion window - Callback Procedure - Hook Procedure - Related Files - Cautions - Explanation of Commands - Samples (Calculator Script) 386 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE 8. 1 Command Line Rules The specification of command lines has the following rules: - Command name, option, and argument are specified for command line. - To divide words, a space (space key or tab key) is used. - At the end of a line, a line feed character or a semicolon is used. - When a command name and an option are entered to the point of identifiability, they are recognized. - In script, command names have to be entered completely. Command format command -options arg1 arg2 arg3 ... 8. 2 Command List Table 8-1 List of Debugger Control Commands Command name address assemble batch breakpoint dbgexit download extwin finish go help hook inspect jump map mdi memory module next refresh register reset Evaluation of address expression Disassemble/line assemble Executing batch (with echo) Setting/deletion of breakpoint Terminating SM+ Download of files Creation of expansion window Returning from function Continuous execution Display of help Setting of hook Symbol inspect Jump to window Setting / deleting memory mapping Setting of expansion window Display/setting of memory Display of the list of files and functions Procedure step Redrawing of window Display/setting of register value and IOR/SFR value Reset Function User's Manual U17246EJ2V0UM 387 CHAPTER 8 COMMAND REFERENCE Table 8-1 List of Debugger Control Commands Command name run step stop upload version watch where wish xcoverage xtime xtrace Reset and execution of CPU Step execution Stop execution Upload Display of the version information Display/setting of variables Trace of stack Start of Tclet Operation of coverage Operation of timer Operation of tracer Function Table 8-2 List of Console/Tcl Commands Command name alias cd clear echo exit history ls pwd source time tkcon unalias which Other Creation of another name Change of directory Clears the screen Echo Close/end Display of history Display of files Check of the directory Execution of batch Measurement of time for commands Console control Deletion of another name Display of the command path or another name Based on Tcl/Tk 8.4 Function 388 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE 8. 3 List of Variables - dcl(chip) - Chip name read only - dcl(prjfile) - Project file name read only - dcl(srcpath) - Source path read only - dcl(ieid) - IE type read only - dcl(iestat) - IE status read only - dcl(bkstat) - Break status read only - env(LANG) - Language - dcl_version - Dcl version read only 8. 4 List of Packages - tcltest - Restoration test - cwind - Automatic window control - BWidget - Toolkit - tcllib - Tcl library - mclistbox - Multi-column list box - combobox - Combo box 8. 5 Key Bind - tcsh + emacs like - Complement of command name [Tab] - Complement of file name [Tab] - HTML help [F1] 8. 6 Expansion window The expansion windows can be created using Tk. In the expansion windows, Widget is allocated with '.dcl' as a root instead of '.'. When the following script files are allocated in bin/idtcl/tools/, an expansion window is added on selecting [Browse] menu - [Others]. The mdi command, an exclusive command for expansion windows, has been added. # Sample.tcl wm protocol .dcl WM_DELETE_WINDOW { exit } mdi geometry 100 50 button .dcl.b -text Push -command exit pack .dcl.b Caution In expansion windows, Tk menu commands cannot be used because of the restrictions of MDI windows. User's Manual U17246EJ2V0UM 389 CHAPTER 8 COMMAND REFERENCE 8. 7 Callback Procedure Expansion windows can hold dcl_asyncproc procedures called by asynchronous messages. proc dcl_asyncproc {mid} { if {$mid == 19} { redraw } } The asynchronous message ID is passed for the argument of the dcl_asyncproc procedure The message IDs are shown below: Table 8-3 Message ID Message ID 9 10 11 12 13 14 15 17 18 19 20 36 37 38 39 40 41 42 45 After changing configuration After registering event After deleting event Before executing After breaking After resetting CPU After resetting SM+ After changing extended option After changing debugger option After downloading After changing memory or register Before starting tracer After stopping tracer Before starting coverage After stopping coverage Before starting timer After stopping timer After clearing trace After resetting symbol Meaning 390 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE 8. 8 Hook Procedure A hook can be set in the SM+ using the hook procedure. The hook procedures are shown below: - BeforeDownload (Hook before downloading) - AfterDownload (Hook after downloading) - AfterCpuReset(Hook after CPU reset during break)) - BeforeCpuRun (Hook before starting execution) - AfterCpuStop (Hook after breaking) By using hook procedures, register values can be changed before downloading programs or after resetting the CPU. An actual example of the procedure is shown below. A hook is valid till the SM+ is closed. [When hook is set with SM+ control command] 1) 2) 3) Create script file a. with an editor. Start up the SM+, select [Browse] menu -> [Console], and open the Console window. If the script file is executed in the window as below, the hook in the script file is set. %hook test.tcl [When hook is set on downloading of project file] 1) Create script file a. with an editor. Caution Be sure that the script file name is the same as the project file. Example: The script file corresponding to test.prj is test.tcl. Allocate test.prj, test.pri, and test.tcl in the same directory. 2) Start up the SM+and read test.prj. The hook in the script file is set. proc BeforeDownload {} { register MM 0x7 register PMC8 0xff register PMC9 0xff register PMCX 0xe0 } proc AfterCpuReset {} { register MM 0x7 register PMC8 0xff register PMC9 0xff register PMCX 0xe0 } User's Manual U17246EJ2V0UM 391 CHAPTER 8 COMMAND REFERENCE 8. 9 Related Files - Executes when the aliases.tcl console is opened. Sets the default alias etc. - Executes when the project file name.tcl project is opened. The hook of BeforeDownload, AfterDownload, AfterCpuReset, BeforeCpuRun and AfterCpuStop can be used. - Executes when the load module name.tcl load module is downloaded. The hook of BeforeDownload, AfterDownload, AfterCpuReset, BeforeCpuRun and AfterCpuStop can be used. 8. 10 Cautions - The separator for file and path is a slash (/). - When a console is open, error messages are output to the console. - To terminate the command forcibly, close the console. - The execution of external commands (DOS commands) is OFF by default. 8. 11 Explanation of Commands In this section, each command is explained using the format shown below. Command name Describes the command name. Input format Describes the input format of the command. In the following explanation, italics indicate an Argument to be supplied by the user, while the argument enclosed in "?" may be omitted. When a command name and an option are entered to the point of identifiability, they are recognized. Functions Explains the functions of the command. Usage example Shows an example of the usage of the command. 392 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE address address - Evaluation of address expression Input format address expression Functions Converts the address expression specified by expression into address. Usage example (IDCON) 1 % address main 0xaa (IDCON) 2 % address main+1 0xab User's Manual U17246EJ2V0UM 393 CHAPTER 8 COMMAND REFERENCE assemble assemble - Disassemble/line assemble Input format assemble ?options? address ?code? Functions Assembles the character strings specified by codefrom the address specified by address. When '.' is specified for address, it is understood as an address continuing from the immediately previous assemble. When code is omitted, it is assembled from the address specified by address. The following are options: They are ignored for assembly. -code -number number Command code is also displayed.It is ignored for assembly. number line is displayed. It is ignored for assembly. Usage example (IDCON) 1 % assemble -n 5 main 0x000000aa B7 PUSH HL 0x000000ab B1 PUSH AX 0x000000ac 891C MOVW AX,SP 0x000000ae D6 MOVW HL,AX 0x000000af A100 MOV A,#0H (IDCON) 2 % assemble main mov a,b (IDCON) 3 % assemble . mov a,b 394 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE batch batch - Executing batch (with echo) Input format batch scriptname Functions Executes in batch with displaying files specified by scriptname on the screen. Nesting is possible. Usage example (IDCON) 1 % clear (IDCON) 2 % batch bat_file.tcl (IDCON) 3 % tkcon save a:/log.txt User's Manual U17246EJ2V0UM 395 CHAPTER 8 COMMAND REFERENCE breakpoint breakpoint - Setting/deletion of breakpoint Input format breakpoint ?options? ?address1? ?address2? breakpoint -delete brkno breakpoint -delete brkno breakpoint -disable brkno breakpoint -information Functions Operates the breakpoint specified by options and address . If a breakpoint can be set correctly, the breakpoint number is returned. The following are options: -software -hardware -execute -before execute -read -write -access -size size -data value -datamask value -pass value -information -delete -disable -enable A software break is specified. A hardware break is specified (default). The address execution break is set (default). The break before address execution is set. An address data read break is set. An address data write break is set. An address data access break is set. The access size is set (8, 16, or 32bit). The data condition is set. The data mask is set. The path count is set. The list of breakpoints is displayed. The breakpoint whose number is specified is deleted. The breakpoint whose number is specified is disabled. The breakpoint whose number is specified is enabled. Usage example (IDCON) 1 % breakpoint main 1 (IDCON) 2 % breakpoint -i 1 Brk00001 enable rammon.c#17 (IDCON) 3 % breakpoint -software sub 2 396 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE (IDCON) 4 % breakpoint -i 1 Brk00001 enable rammon.c#17 2 Brk00001 enable rammon.c#8 (IDCON) 5 % breakpoint -disable 2 (IDCON) 6 % breakpoint -i 1 Brk00001 enable rammon.c#17 2 Brk00001 disable rammon.c#8 (IDCON) 7 % breakpoint -delete 1 2 Brk00001 disable rammon.c#8 User's Manual U17246EJ2V0UM 397 CHAPTER 8 COMMAND REFERENCE dbgexit Tdbgexit - Terminating SM+ Input format dbgexit ?options? Functions Terminate the SM+. The following are options: -saveprj Project is saved on terminating SM+. Usage example (IDCON) 1 % dbgexit -saveprj 398 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE download download - Download of files Input format download ?options? filename ?offset? Functions Downloads files specified with filename according to options. If offset is specified, the address is shifted by the offset (if the data is in binary format, the load start address is specified for offset). -binary -coverage -append -nosymbol -symbolonly -reset -information Binary format data is downloaded. Coverage data is downloaded. Additional download is executed. [V850] Download is executed. Symbol information is not read. Symbol information is read. CPU is reset after download. Download information is displayed. Usage example (IDCON) 1 % download test.lmf User's Manual U17246EJ2V0UM 399 CHAPTER 8 COMMAND REFERENCE extwin extwin - Creation of expansion window Input format extwin scriptfile Functions Creates expansion window with scriptfile. Usage example (IDCON) 1 % extwin d:/foo.tcl 400 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE finish finish - Returning from function Input format finish Functions Executes until it returns to the program that called the current function. Usage example (IDCON) 1 % finish User's Manual U17246EJ2V0UM 401 CHAPTER 8 COMMAND REFERENCE go go - continuous execution Input format go ?options? Functions Executes program continuously.If -waitbreak is specified, the command waits until the program stops. The following are options: -ignorebreak -waitbreak Breakpoint is ignored. The command waits for the program to stop. Usage example (IDCON) 1 % go -w 402 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE help help - Display of help Input format help Functions Displays Dcl help. Usage example (IDCON) 1 % help User's Manual U17246EJ2V0UM 403 CHAPTER 8 COMMAND REFERENCE hook hook - Setting of hook Input format hook scriptfile Functions Sets the procedure for hook with scriptfile. The hook setting is initialized when the project file is loaded and when the SM+ is reset. Usage example (IDCON) 1 % hook d:/foo.tcl 404 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE inspect inspect - Symbol inspect Input format inspect ?options? progname pattern Functions Searches and displays the load module symbol specified with progname using the regular expression of pattern. The following regular expressions can be used. ? * [chars] \x The following are options: -nocase -address Does not distinguish between upper and lowercase. Displays in pair with symbol address. Match 1 character Match characters other than 0 Match chars character. Range specification such as [a-z/0-9] also possible. Match character x. ? * [ ] \ specification also possible. Usage example (IDCON) 1 % inspect test1.out {[a-z]*} User's Manual U17246EJ2V0UM 405 CHAPTER 8 COMMAND REFERENCE jump jump - Jump to window Input format jump -source -line filename ?line? jump ?options? address Functions Displays the window specified by options. -source -assemble -memory -coverage -line -focus The Source window is displayed from the address specified by address. The Assemble window is displayed from the address specified by address. The Memory window is displayed from the address specified by address. The Coverage window is displayed from the address specified by address. The command is moved to the line specified by line. The Focus is moved to the window displayed. Usage example (IDCON) 1 % jump -s main (IDCON) 2 % jump -s -l mainfile.c 10 (IDCON) 3 % jump -m array 406 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE map map - Setting/deletion of memory mapping Input format map options address1 address2 ?accsize? Functions Sets, deletes, and displays memory mapping. The access size of 8, 16, or 32 is specified by accsize (unit:byte, the default is 8). The following are options: -erom -eram -target -stack -protect -clear -information Alternate ROM is mapped. Alternate RAM is mapped. Target area is mapped. [V850] [78K0] Stack area is mapped. [78K] I/O protect area is mapped. [V850] [78K0] All the settings for the mapping are deleted. Refer to the setting for the mapping. Usage example (IDCON) 1 % map -i 1: 0 0x7fff 8 {IROM} 2: 0x8000 0x87ff 8 {Target RRM} 3: 0x8800 0x9fff 8 {Target} 4: 0xa000 0xf7ff 8 {NonMap} 5: 0xf800 0xfaff - {NonMap} 6: 0xfb00 0xfedf 8 {Saddr} 7: 0xfee0 0xfeff 8 {Register} 8: 0xff00 0xffff 8 {SFR} (IDCON) 2 % map -erom 0x100000 0x10ffff (IDCON) 3 % map -c User's Manual U17246EJ2V0UM 407 CHAPTER 8 COMMAND REFERENCE mdi mdi - Setting of expansion window Input format mdi geometry ?x y? width height mdi title string Functions Sets the size and title name of the expansion window. The command can be used only from the expansion window. Usage example (IDCON) 1 % mdi geometry 0 0 100 100 (IDCON) 2 % mdi title foo 408 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE memory memory - Display/setting of memory Input format memory ?options? address ?value? memory ?options? -fill address1 address2 value memory ?options? -copy address1 address2 address3 Functions Sets value in the memory of the address specified by address according to options. If value is omitted, display the value of the memory of the address specified by address. If -fill is specified, data from address1 to address2 is filled with value . If -copy is specified, data from address1 to address2 is copied to address3. The following are options: -byte -halfword -word -fill -copy -noverify Displayed/set in one-byte units (default). Displayed/set in halfword units. [V850] Displayed/set in word units. The data is filled in. The data is copied. Verification is not executed on writing. Usage example (IDCON) 1 % memory 100 0x10 (IDCON) 2 % memory 100 2 (IDCON) 3 % memory 100 0x02 (IDCON) 4 % memory -fill 0 1ff 0 User's Manual U17246EJ2V0UM 409 CHAPTER 8 COMMAND REFERENCE module module - Display of the list of files and functions Input format module progname ?filename? Functions Displays the list of files and functions of the load module specified by progname. If filename is not specified, the list of files is displayed. If filename is specified, the list of functions of the specified files is displayed. Usage example (IDCON) 1 % module rammon.lmf 1: rammon.c (IDCON) 2 % module rammon.lmf rammon.c 1: rammon.c sub1 2: rammon.c main 410 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE next next - Procedure step Input format next ?options? Functions Executes the procedure steps. If functions are called, the step stops after executing function. The following are options: -source -instruction The command is executed in source line units (default). The command is executed in command units. Usage example (IDCON) 1 % next -i (IDCON) 2 % next -s User's Manual U17246EJ2V0UM 411 CHAPTER 8 COMMAND REFERENCE refresh refresh - Redrawing of window Input format refresh Functions Redraws the window and updates the data. Usage example (IDCON) 1 % batch foo.tcl (IDCON) 2 % refresh 412 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE register register - Display/setting of register value and IOR/SFR value Input format register ?options? regname ?value? Functions Sets value in the register specified with regname. If value is omitted, displays the value of the register specified by regname. The following are options: -force Compulsory reading or writing is executed. Usage example (IDCON) 1 % register pc 0x0100 (IDCON) 2 % register pc 200 (IDCON) 3 % register pc 0x200 User's Manual U17246EJ2V0UM 413 CHAPTER 8 COMMAND REFERENCE reset reset - Reset Input format reset ?options? Functions Resets the SM+ , CPU, symbols or events. If options are omitted, the CPU is reset. The following are options: -cpu -debugger -symbol -event CPU is reset (default). The SM+ is reset. Symbol is reset. Event is reset. Usage example (IDCON) 1 % reset 414 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE run run - Reset and execution of CPU Input format run ?options? Functions Resets the program and executes it. If -waitbreak is not specified, the command does not wait until the program stops. The following are options: -waitbreak The command waits for the program to stop. Usage example (IDCON) 1 % run (IDCON) 2 % run -w User's Manual U17246EJ2V0UM 415 CHAPTER 8 COMMAND REFERENCE step step - Step execution Input format step ?options? Functions Executes step execution. If functions are called, the command stops at the head of the functions. The following are options: -source -instruction The command is executed in source line units (default). The command is executed in instruction units. Usage example (IDCON) 1 % step -i (IDCON) 2 % step -s 416 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE stop stop - Stop executing Input format stop Functions Stops the program forcibly. Usage example (IDCON) 1 % run (IDCON) 2 % stop User's Manual U17246EJ2V0UM 417 CHAPTER 8 COMMAND REFERENCE upload upload - Upload Input format upload ?options? filename address1 address2 Functions Saves the memory data or coverage data within the specified range in a file. The following are options: -binary -coverage -intel -motorola -tektronix -force The data is saved in binary format. The coverage data is saved. The data is saved in Intel HEX format (default). The data is saved in Motorola HEX format. The data is saved in Tektronix HEX format. The file is overwritten. Usage example (IDCON) 1 % upload -b foo.hex 0 0xffff 418 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE version version - Display of the version information Input format version Functions Displays the version of the SM+. Usage example (IDCON) 1 % version GUI : E2.00y [31-May-99] Devicefile : 78K0[uPD780034] E1.01a Debugger : 78K/0 Debugger E2.50c [02-Apr-99] Executer : 78K/0 Executer E1.3c Packet translator : 78K/0 Packet E2.00w Assembler : 78K/0 Asm/Disasm E1.15a [01-Apr-99] Tcl/Tk : 8.1.1 User's Manual U17246EJ2V0UM 419 CHAPTER 8 COMMAND REFERENCE watch watch - Display/setting of variables Input format watch ?options? variable ?value? Functions Displays and sets the variables. The following are options: -binary -octal -decimal -hexdecimal -string -sizeof -encoding name The value is displayed in binary digits. The value is displayed in octal digits. The value is displayed in decimal digits. The value is displayed in hexdecimal digits. The value is displayed in character strings. The size, instead of the value, of variables is displayed in decimal digits. Encoding during character string display is specified. By default, system encoding is used. name (encoding name) is based on the Tcl specification (shiftjis, euc-jp, etc.). Usage example (IDCON) 1 % watch var 0x10 (IDCON) 2 % watch -d var 16 (IDCON) 3 % watch array\[0\] 0xa 420 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE where where - Trace of stack Input format where Functions Executes the back-trace of the stack. Usage example (IDCON) 1 % where 1: test2.c#sub2(int i)#13 2: test.c#num(int i)#71 3: test.c#main()#82 User's Manual U17246EJ2V0UM 421 CHAPTER 8 COMMAND REFERENCE wish wish - Startup of Tclet Input format wish scriptname Functions Starts up the script using Tk (Tclet). The expansion window can be created with Tclet. Usage example (IDCON) 1 % wish test.tcl 422 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE xcoverage xcoverage - Operation of coverage Input format xcoverage option Functions Operates coverage. The following are options: -start -stop -clear The coverage starts on executing the program. The coverage stops on executing the program. The coverage memory is cleared. Usage example (IDCON) 1 % xcoverage -start (IDCON) 2 % xcoverage -stop (IDCON) 3 % xcoverage -clear User's Manual U17246EJ2V0UM 423 CHAPTER 8 COMMAND REFERENCE xtime xtime - Operation of timer Input format xtime option Functions Operates timer. The following are options: -start -stop -gobreak Timer starts on executing the program. Timer stops on executing the program. Time from Go to Break is displayed with clock. Usage example (IDCON) 1 % xtime -start (IDCON) 2 % xtime -stop 424 User's Manual U17246EJ2V0UM CHAPTER 8 COMMAND REFERENCE xtrace xtrace - Operation of tracer Input format xtrace -dump ?-append? frameno ?filename? xtrace -start xtrace -stop xtrace -clear xtrace -addup ?bool? xtrace -mode ?mode? Functions Operates tracer. The following are options: -start -stop -clear -dump The tracer starts on executing the program. The tracer stops on executing the program. Clears the trace memory. The trace data is dumped (default). The dump result is redirected to the console window. If the file name is specified, the dump result is written in the file. The dump result is added to a file. Whether the time tag is integrated or not is selected. When bool is omitted, the current mode is displayed. The trace control mode (any one of: all, cond, nonstop, fullstop, fullbreak, delaystop, delaybreak, machine, or event) is selected. When mode is omitted, the current mode is displayed. -append -addup ?bool? -mode ?mode? Usage example (IDCON) 1 % xtrace -start (IDCON) 2 % xtrace -stop (IDCON) 3 % xtrace -dump 3 _ 01685 2 000000BC M1 br _sub2+0x2 _ 01686 4 0000009A BRM1 st.w r6, 0x8[sp] _ 01687 3 0000009E BRM1 st.w r0, 0x0[sp] (IDCON) 4 % xtrace -clear (IDCON) 5 % xtrace -addup true User's Manual U17246EJ2V0UM 425 CHAPTER 8 COMMAND REFERENCE 8. 12 Samples (Calculator Script) The script of the expansion window in which the calculator script is described and its execution screen are shown below. Script of expansion window # Calculator.tcl mdi geometry 100 100 set top .dcl entry $top.e -relief sunken -textvariable v frame $top.f -height 120 -width 120; pack $top.e -fill x; pack $top.f -fill both -expand 1set i 0; set v {}; set r 0.25 foreach n {7 8 9 / 4 5 6 * 1 2 3 - 0 = + C} { if {$n == "=" || $n == "C"} { button $top.f.b$n -text $n } else { button $top.f.b$n -text $n -command "$top.e insert end $n" } place $top.f.b$n -relx [expr ($i%4)*$r] -rely [expr ($i/4)*$r] -relw $r -relh $r } bind $top.f.bC <1> {$top.e delete 0 end} bind $top.f.b= <1> {catch {expr $v} v} Figure 8-1 Execution Screen incr I 426 User's Manual U17246EJ2V0UM APPENDIX A EXPANSION WINDOW APPENDIX A EXPANSION WINDOW - Overview - Sample List of Expansion Window - Activation - Explanation of each sample window A. 1 Overview With the SM+, the user can create custom windows in addition to the existing windows. The Tcl (Tool Command Language) interpreter and the commands for controlling the debugger are implemented in the SM+. Users can create windows using this Tcl. The SM+ is supplied with samples of the following expansion windows. A. 2 Sample List of Expansion Window Table A-1 List of Expansion Window (Sample) Window Name Function Displays a list of the source files and functions. Searches a character string. This is the memory window for real-time RAM monitoring. Sets the hook procedure. Writes to or reads from the specified address. List window Grep window RRM window Hook window Memory Mapped I/O window A. 3 Activation The expansion window can be activated by selecting List, Grep, RRM, Hook, or Memory in [Others] on the [Browse] menu. Remark Each .tcl file is installed in NECTools32\BIN\idtcl\tools. A. 4 Explanation of each sample window User's Manual U17246EJ2V0UM 427 APPENDIX A EXPANSION WINDOW List window The lists of the source files and functions are displayed in a tree format in this window. When a function name in the list is clicked, the corresponding source is displayed. Figure A-1 List Window When a function name in the list is clicked, the corresponding function portion is displayed in the Source window. 428 User's Manual U17246EJ2V0UM APPENDIX A EXPANSION WINDOW Grep window Search for a character string is performed in the files under the source path. When the search result is clicked, the corresponding source is displayed. Figure A-2 Grep Window By clicking a character string line in the search result,the coressponding character string portion is displayed in the Source window. Object Pattern button Function Input the character string to be searched. Marks the searched character string. Clears the marking. Put the cursor on a section in the search result and click this button to open the corresponding file. Select whether or not to distinguish uppercase and lowercase. Specify the type of the file to be searched. User's Manual U17246EJ2V0UM 429 APPENDIX A EXPANSION WINDOW RRM window This is a dedicated window for RAM monitoring. The address area in which a value was changed in the RAM area during program execution is highlighted with a color. The display range is 1 KB. With reading RAM, execution of the user program momentarily breaks. On this window, the start address of the RAM area can be changed while the user program is being executed. Caution All data are not read at the same time (because data of 1 KB is divided and read in word units). Figure A-3 RRM Window Object Address Function Input the start address to be displayed (automatically aligned to 1 KB.) Switch the start address display. Reads data from the memory. The color can be customized. The default color is red. Specify whether or not to hold the color highlighting. Selected: Once a value is changed, the color highlighting is held until a break occurs. Unselected: The color is cleared if there is no change of values(default). Closes this window. 430 User's Manual U17246EJ2V0UM APPENDIX A EXPANSION WINDOW Hook window This window is used to set a hook to the debugger, using a hook procedure. The hook procedure enables changing the register value before downloading a program, or after a CPU reset. On this window, a hook can be set by using the following four tabs. - [BeforeDownload] tab: Hook before downloading - [AfterCpuReset] tab: Hook after CPU reset during break - [BeforeCpuRun] tab: Hook before start of execution - [AfterCpuStop] tab: Hook after break Remark By setting a IOR by using the [BeforeDownload] tab before downloading the load module, for example, downloading can be executed at high speeds. Access to the external memory is also facilitated by using this tab. [V850] If the setting is saved as "project-file-name.tcl" in the directory where the project is stored, the setting is executed when the project is next opened. Figure A-4 Hook Window Object [BeforeDownload]Tab Function Hook before downloading Before downloading is performed, the register values input to the tab are automatically overwritten by the specified value. Hook after CPU reset during break after resetting CPU, the register values input to the tab are automatically overwritten by the specified value. Hook before starting execution before starting execution, the register values input to the tab are automatically overwritten by the specified value. [AfterCpuReset]Tab [BeforeCpuRun]Tab User's Manual U17246EJ2V0UM 431 APPENDIX A EXPANSION WINDOW Object [AfterCpuStop]Tab Function Hook after breaking After breaking, the register values input to the tab are automatically overwritten by the specified value. All the commands described on the tabs are tested. Saves all the tab contents to a file. If the SM+ was activated from a project file, the file is saved as "project-filename.tcl". Clears all the descriptions on the tabs. Specify the program register and the IOR/SFR for the register name. 432 User's Manual U17246EJ2V0UM APPENDIX A EXPANSION WINDOW Memory Mapped I/O window Data is explicitly read or written at a specified address in this window. When a write is performed in the Memory window, the data is internally read and verified by the SM+. In addition, the memory can also be read simply by scrolling in the Memory window. On the Memory Mapped I/O window, however, the above operations are not performed. Therefore, this window is useful for reading or writing a specific address. While the user program is being executed, it momentarily breaks before data is written in this window. Figure A-5 Memory Mapped I/O Window Object Address Function Input the address to display. The display target address changes by pressing the Enter key or clicking the User's Manual U17246EJ2V0UM 433 APPENDIX A EXPANSION WINDOW Memory Mapped I/O dialog box This dialog box can be opened by clicking the Object Address Function Input the address to be written. The address corresponding to the data for which the cursor is placed in the Memory Mapped I/O window is displayed by default. Input the value to be written. Select the size of the data to be written. The size specified in the Memory Mapped I/O window is selected by default. Data is written to the specified address with the specified size. Closes this dialog box. Value Data Size 434 User's Manual U17246EJ2V0UM APPENDIX B INPUT CONVENTIONS APPENDIX B INPUT CONVENTIONS - Usable Character Set - Symbols - Numeric Values - Expressions and Operators - File Names B. 1 Usable Character Set Table B-1 List of Character Set Classification Character Uppercase : A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Lowercase : a b c d e f g h i j k l m n o p q r s t u v w x y z 0123456789 @ _ [V850] @ _ ? [78K] Alphabetic characters Numerals Character equivalent to alphabetic character Table B-2 List of Special Characters Character ( ) + * / % ~ Name Left parenthesis Right parenthesis Plus Minus Asterisk Slash Percent Tilde Vertical line Circumflex Ampersand Left bracket Right bracket Exclamation Dollar Changes operation order. Changes operation order. Usage Addition operator or positive sign Subtraction operator or negative sign Multiplication operator or indirect reference operator Division operator Remainder operator Complement operator Bit sum operator Bit difference operator Bit product operator or address operator Array subscript operator or base register specification symbol [V850] Array subscript operator or indirect display symbol [78K] Absolute addressing start symbol [78K] Relative addressing start symbol [78K] | ^ & [ ] ! $ User's Manual U17246EJ2V0UM 435 APPENDIX B INPUT CONVENTIONS Character # . , Name Sharp mark Period Comma Usage Symbol indicating an immediate value [78K] Direct member operator or bit position specifier Delimiter between operands B. 2 Symbols (a) A symbol consists of characters A to Z, a to z, @, _ (underbar), . (period) and 0 to 9. [V850] A symbol consists of characters A to Z, a to z, @, _ (underbar), ?, and 0 to 9. [78K] (b) A symbol must start with a character other than numerals 0 to 9. (c) Uppercase characters (A to Z) and lowercase characters (a to z) are distinguished. (d) A symbol must be no more than 2048 characters long (if a symbol of more than 2048 characters is defined, only the first 2048 characters are valid). (e) A symbol is defined by loading a load module file. (f) Symbols are classified into the following types by the valid range: - Global symbol (assembly language, structured assembly language [78K] , C language) - Static symbol (C language) In-file static symbol In-function static symbol - Local symbol (C language) - In-module local symbol (assembly language, structured assembly language)[78K] In-file local symbol In-function local symbol In-block local symbol (g) The following symbols are available for each language used: Assembly language, structured assembly language [78K] , label name, constant name [78K] , bit symbol name C language Variable name (including pointer variable name, enumeration type variable name, array name, structure name, and union name) Function name, label name Array element, structure element, union element, bit field (if the symbol is an array, structure, or union) (h) A symbol can be described instead of an address or numeric value. (i) The valid range of a symbol is determined based on the source debug information when the source file is assembled or compiled. (j) (k) Describe only the symbol name of a global symbol. A local symbol is expressed in pairs with a file name. 436 User's Manual U17246EJ2V0UM APPENDIX B INPUT CONVENTIONS B. 3 Numeric Values The following four types of numeric values can be used. The input format of each type is as shown below. The suffix (bold) and the alphabetic characters of hexadecimal numbers may be uppercase or lowercase characters. If the first character is A to F, 0 must be prefixed to it. In the input field of SM+, decimal numbers or hexadecimal numbers are alternately selected, depending on the default radix. Table B-3 Input Format of Numeric Values Numeric Value Binary number Octal number nY n...nY (n=0,1) nO n...nO (n=0,1,2,3,4,5,6,7) nQ n...nQ (n=0,1,2,3,4,5,6,7) n n...n nT n...nT (n=0,1,2,3,4,5,6,7,8,9) n n...n nH n...nH 0xn 0xn...n (n=0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F) Input Format Decimal number Hexadecimal numbers B. 4 Expressions and Operators (1) Expressions An expression consists of constants, register names, IOR/SFR name and symbols coupled by operators. If IOR/SFR name, label name, function name, or variable name is described as a symbol, an address is calculated as the value of the symbol. The elements making up an expression, except operators, are called terms (constants and labels). Terms are called the first term, the second term, and so on, starting from the left. User's Manual U17246EJ2V0UM 437 APPENDIX B INPUT CONVENTIONS (2) Operators The following operators of the C language can be used: Table B-4 List of Operators Symbol Arithmetic operator + * / MOD % - sign + sign Logical operator NOT ~ AND & OR | XOR ^ Shift operator SHR >> SHL << Right shift Shifts the value of the first term by the value (number of bits) of the second term to the right, and returns the results. As many 0s as the number of shifted bits are inserted in the higher bits. Shifts the value of the first term by the value (number of bits) of the second term to the left, and returns the results. As many 0s as the number of shifted bits are inserted in the lower bits. Negation Logical product Logical sum Exclusive logical sum Logically negates each bit of the term, and returns the results. Obtains the logical product of the values of the first and second terms on each bit, and returns the results. Obtains the logical sum of the values of the first and second terms on each bit, and returns the results. Obtains the exclusive logical sum of the values of the first and second terms on each bit, and returns the results. Addition Subtraction Multiplication Division Remainder Unary operator (negative) Unary operator (positive) Returns the sum of the first and second terms. Returns the difference between the first and second terms. Returns the product of the first and second terms. Divides the value of the first term by the value of the second term, and returns the integer of the results. Divides the value of the first term by the value of the second term, and returns the remainder of the results. Returns 2's complement of the value of the term. Returns the value of the term. Meaning Explanation Left shift Byte separation operator HIGH LOW Higher byte Lower byte Of the lowest 16 bits of the term, returns the higher 8 bits. Of the lowest 16 bits of the term, returns the lower 8 bits. Word separation operator HIGHW LOWW Other Higher word Lower word Of the 32 bits of the term, returns the higher 16 bits. Of the 32 bits of the term, returns the lower 16 bits. 438 User's Manual U17246EJ2V0UM APPENDIX B INPUT CONVENTIONS Symbol ( ) Meaning Left parenthesis Right parenthesis Explanation Performs the operation in ( ) before the operation outside ( ). '(' and ')' are always used in pairs. (3) Rules of operation Operations are performed according to the priority of the operators. Table B-5 Operator Priority Priority 1 2 3 4 5 6 Lower Higher (,) + sign, - sign, NOT, ~, HIGHT, LOW, HIGHW, LOWW *, /, MOD, %, SHR, >>, SHL, << +, AND, & OR, |, XOR, ^ Operators - If the priorities of the operators are the same, the operation is performed from the left toward the right. - Performs the operation in ( ) before the operation outside ( ). - Each term in an operation is treated as unsigned 32-bit data. - All operation results are treated as unsigned 32-bit data. - If an overflow occurs during operation, the lower 32 bits are valid, and the overflow is not detected. (4) Terms To describe a constant for a term, the following numeric values can be described. Table B-6 Range of Radixes Radix Binary number Octal number Decimal number Hexadecimal numbers Range 0Y <= value <= 1111111111111111111111111111111Y (32 digits) 0O <= value <= 37777777777O -2147483648 <= value <= 4294967295 (A negative decimal number is internally converted into a 2's complement.) 0H <= value <= 0FFFFFFFH User's Manual U17246EJ2V0UM 439 APPENDIX B INPUT CONVENTIONS B. 5 File Names The following regulations apply to the source file names and load module file names. (1) Source file names and load module file names File names are composed of a to z, A to Z, 0 to 9, ., _, +, and -. File names must start with a character other than ., +, or -. File names cannot be prefixed or suffixed by a period (.) or space. File names are not case-sensitive. A file name consists of up to 259 characters including the path. (2) Other file names Other file names comply with Windows file name regulations. The following characters cannot be used in file names. \/:*?"<>|; File names cannot be prefixed or suffixed by a period (.) or space. File names are not case-sensitive. A file name consists of up to 259 characters including the path. 440 User's Manual U17246EJ2V0UM APPENDIX C KEY FUNCTION LIST APPENDIX C KEY FUNCTION LIST Table C-1 Key Function List Key BackSpace Function Deletes one character before the cursor and moves the cursor to the position of the deleted character. At this time, the character string following the cursor moves forward. - Deletes one character after the cursor and move the character string following the cursor forward. - Deletes a various event condition selected in the Event Manager or each event dialog box. - Deletes the data selected in the Watch window. Alternately selects the insert mode and overwrite mode in the Source window and Assemble window. However, this key is invalid in the Memory, Register, and IOR windows, and only the overwrite mode can be used as an input mode. Loads the entire display screen to the clipboard as a bitmap image (function of Windows). - Closes the pull-down menu. - Closes the modal dialog box. - Restores the input data. Moves the cursor to the menu bar. Moves the cursor to the end of the line. Moves the cursor to the beginning of the line. Scrolls the screen one screen up. The cursor also moves up to the top of the screen. Scrolls the screen one screen down. The cursor also moves up to the top of the screen. Inserts one blank character. Moves the cursor to the next item. Moves the cursor up. If the cursor is at the bottom of the screen, scrolls the screen up one line at a time. Moves the cursor down. If the cursor is at the top of the screen, scrolls the screen down one line at a time. Moves the cursor to the left. If the cursor is at the left most position on the screen, scrolls the screen one column to the right. Moves the cursor to the right. If the cursor is at the right most position on the screen, scrolls the screen one column to the left. - Sets the input data. - Presses the default push button. Opens the Help window. Forcibly stops program execution. Same function as [Run] menu -> [Stop]. Resets the CPU. Same function as [Run] menu -> [CPU Reset]. Delete Insert PrintScreen Esc Alt End Home PageUp PageDown Space Tab Up arrow key Down arrow key Right arrow key Left arrow key Enter F1 F2 F3 User's Manual U17246EJ2V0UM 441 APPENDIX C KEY FUNCTION LIST Key F4 F5 F6 F7 F8 F9 F10 Shift+End Shift+Home Shift+Left arrow key Shift+Right arrow key Shift+F6 Shift+F9 Ctrl+End Ctrl+Home Ctrl+Left arrow key Function Resets the CPU and executes the program. Same function as [Run] menu -> [Restart]. Executes the program. Same function as [Run] menu -> [Go]. Executes the program to the cursor position in the Source or Assemble window. Same function as [Run] menu -> [Come Here]. The user program is real-time executed until execution returns. Same function as [Run] menu -> [Return Out]. Step execution. Same function as [Run] menu -> [Step In]. Sets a breakpoint at cursor position in Source or Assemble window. Same function as [Run] menu -> [Break Point]. Next step execution. Same function as [Run] menu -> [Next Over]. Expands the selection range to the end of the line. Expands the selection range to the beginning of the line. Expands the selection range one character to the left. Expands the selection range one character to the right. Executes the program from the cursor position in the Source or Assemble window. Same function as [Run] menu -> [Start From Here]. Resets the CPU. Same function as [Run] menu -> [CPU Reset]. Displays the last line. The cursor will also move to the last line. Displays the first line. The cursor will also move to the first line. Moves the cursor one word to the left. If the cursor at the left most position on the screen, scrolls the screen one column to the right. Moves the cursor one word to the right. If the cursor at the right most position on the screen, scrolls the screen one column to the left. Ignores break points being set, and executes the program. Same function as [Run] menu -> [Ignore break points and Go]. Sets the address at the cursor position in the Source window or Assemble window to the PC. Same function as [Run] menu -> [Change PC]. Selects all the events registered to the Event Manager. Same function as [View] menu -> [Select All Event] in the Event Manager. Copies a selected character string and saves it to the clipboard buffer. Disassembles and displays the results from the jump destination address specified by the data value selected in the current window.Opens the Assemble window. Same function as [Jump] menu -> [Assemble]. Opens the source file displayed in the active Source window with the editor specified by the PM+ when the PM+ is running. Same function as [Edit] menu -> [Edit Source]. Performs a search.Opens the search dialog box corresponding to the current window. Same function as [View] menu -> [Search...]. Ctrl+Right arrow key Ctrl+F5 Ctrl+F9 Ctrl+A Ctrl+C Ctrl+D Ctrl+E Ctrl+G 442 User's Manual U17246EJ2V0UM APPENDIX C KEY FUNCTION LIST Key Ctrl+I Function Displays the coverage contents from the jump destination address specified by the data value selected in the current window. Opens the Coverage window. Same function as [Jump] menu -> [Coverage]. Moves the display position. Opens the each dialog box, depending on the current window. Same function as [View] menu -> [Move...]. Displays the memory contents from the jump destination address specified by the data value selected in the current window. Opens the Memory window. Same function as [Jump] menu -> [Memory...]. Loads a view file, source file, or text file. Opens the View File Load dialog box. The operation will differ depending on the extension of the file. view file: Displays the file in the corresponding window. Others: Displays the file in the Source window. Same function as [File] menu -> [Open...]. Saves the data displayed in the current window to the view file. Same function as [View] menu -> [Save...]. Displays the corresponding source text and source line, using the data value selected in the current window as the jump destination address. Opens the Source window. Same function as [Jump] menu -> [Source Text]. Pastes the contents of the clipboard buffer to the text cursor position. Temporarily displays the contents of the specified data. Opens the Quick Watch dialog box. Same function as [View] menu -> [Quick Watch...]. Cuts a selected character string and saves it to the clipboard buffer. Same function as [Edit] menu -> [Cut]. Expands the selection range one word to the left. Expands the selection range one word to the right. Ctrl+J Ctrl+M Ctrl+O Ctrl+S Ctrl+U Ctrl+V Ctrl+W Ctrl+X Ctrl+Shift+Left arrow key Ctrl+Shift+Right arrow key User's Manual U17246EJ2V0UM 443 APPENDIX D MESSAGES APPENDIX D MESSAGES - Display Format - Types of Messages - Message Lists D. 1 Display Format Messages are output to the error/warning dialog box. By pressing the F1 key while the error/warning dialog box is open, the related online help files are displayed. Figure D-1 Error/Warning Messages Error types Error No.(hexadecimal number) 444 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES D. 2 Types of Messages The SM+ outputs the following types of messages. Table D-1 Types of Messages Types Output messages of debugger block (type + 4-digit) Axxxx Fatal error messages Stops processing, and terminates the debugger. If this error occurs, debugging cannot be continued. Syntax error messages Stops processing, and opened windows and dialog boxes are closed. Warning messages or question messages Stops processing, but opened windows and dialog boxes are not closed. Meaning Fxxxx Wxxxx Output messages of simulator block (type + 5-digit) Exxxxx Wxxxxx Error messages A message is outputted and processing stops. Warning messages A message is outputted and processing continues. User's Manual U17246EJ2V0UM 445 APPENDIX D MESSAGES D. 3 Message Lists < X0000~ > < X1000~ > < X2000~ > < X3000~ > < X4000~ > < X5000~ > < X6000~ > < X7000~ > < X8000~ > < X9000~ > < Xa000~ > < Xb000~ > < Xc000~ > (1) X0000~ F0002: This feature is not supported. F0100 : Can not communicate with ICE. Please confirm the installation of the device driver for the PC interface board. 1) The driver may not be correctly installed. Reinstall the driver. A0101: Can not find initialization file (expc.ini). A0102: Host name not found. F0103: Data transfer to ICE is timed out. Please confirm the power of ICE, connection of the interface cable, or I/O address of the PC interface board. F0104: Data receive from ICE is timed out. Please confirm the power of ICE, connection of the interface cable, or I/O address of the PC interface board. A0105: Failed in reading device file (d3xxx.800). [V850] Failed in reading device file (d0xxx.78k). [78K] 1) Necessary files may be damaged. Reinstall the device file. A0106: Illegal data received. 1) Check the power of the in-circuit emulator, cable connections, and setting of the interface board and restart the debugger. A0107: Can not communicate with ICE. A0108: Failed in reading initialization file (expc.ini). A0109: Can not communicate with ICE. Please terminate the debugger and check the power of ICE or the connection of cable then restart the debugger. 1) An error may have occurred during USB communication (such as disconnection of power or cable) or IECUBE is faulty (IECUBE). F010a: Can not communicate. Please confirm the availability of the communication port. A01a0: No response from the evachip. Please confirm the signal of the CLOCK or RESET WAIT, HLDRQ and so on.(IECUBE) No response from the CPU. Please confirm the signal of the CLOCK or RESET WAIT, HLDRQ and so on.(IE-V850E1-CD-NW) No response from the emulation CPU. Please confirm the signal of the CLOCK or RESET(,WAIT) and so on. [78K0] [78K0S] 1) Check the HOLD signal, WAIT signal, clock signal, etc. The IOR value (or SFR value) may not be correct. A01a1: Failed in reading ie703000.ie. 446 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES A01a2: Break board is not connected. A01a3: Emulation board is not connected. A01a4: Board configuration of ICE is not consistent. A01a5: POD/EM1 board is not connected. A01a6: Executor is running. A01a7: Failed in reading micro program file (m0xxx.78k). A01a8: Failed in reading initialization file (expc.ini). [78K] Failed to find configuration file (lv8hw.ini). [V850] A01ad: Please update the device driver for the PC interface board. 1) The device driver may be old. Install the latest device driver. A01ae: Failed in reading initialization file (expc.ini).(78K) Failed in reading configuration file (lv8hw.ini). (V850) A01af: Failed in executing monitor command. A01b0: Can not communicate with monitor program. Please check the availability of communication port, the setting of CPU board or the type of cable. A01b1: Can not communicate with monitor program. Please terminate the debugger and check the power of CPU board or the connection of cable then restart the debugger. A01d0: Not enough memory in starting simulator. A01d1: Not enough memory in starting simulator. F0200: Verification error occurred. Failed in writing memory. 1) External memory could not be accessed, as it is not set. Change the register values necessary for accessing the external memory using the IOR/SFR window or Hook Procedure before download. F02a0: Bus hold error. 1) CPU is in the bus-hold status. Reset the debugger. F02a2: Can not compulsory break. F02a3: Reset under continuation. F02d2: Not enough memory for trace-buffer. F0300: User program is running. F0301: User program is being breaked. F0302: User program is being traced. F0303: Not traced. F0304: Trace memory is not set. F0306: No trace block exists. F0307: No event condition exists. F0308: No timer measurement is done. F0309: No trigger frame exists. F030a: Tracer is being stopped. User's Manual U17246EJ2V0UM 447 APPENDIX D MESSAGES F030b: Specified snap-event has not been registered. F030c: Specified stub-event has not been registered. F030d: Timer is running. F030e: Memory copy area is overlapped. F030f: Trace has been already set. F0310: Event condition is not set. F0311: Too many valid timer event conditions. F0312: Specified timer event is not set. F0313: Illegal map range. 1) Check the map range in the Configuration dialog box. When mapping to external memory has been performed, change the register values necessary for accessing the external memory using the IOR/ SFR window or Hook Procedure before download). F0314: Only trace delay mode can set with delay trigger. F0315: Delay trigger cannot set without trace delay mode. F0316: Overflowed the number of mapping. F03a0: Target is not turned on. 1) Check the target power supply. Check the cable connecting the in-circuit emulator and target board. Check that the VDD signal is input to the connector of the target board. F03a1: Step execution is being done. F03a2: Timer and Tracer are running. F03a3: Event link and BRS events are mixed. F03d0: Back-trace is being executed. F03d1: Back-trace is being stopped. F03d2: Back-trace execution point overrun oldest frame. F03d3: Register status or Memory status cannot be set up other than Phase1 of event link. F03d4: No back-trace information exists. F03d5: Last command can not be backstepped. F0400: Illegal condition. 1) Settings of the used in-circuit emulator and those of the Configuration dialog box may not match. Check the Chip selection. F0401: Result of timer measurement overflowed. F0402: Too many event conditions with path count. F0403: Too many address range conditions. F0404: Too many simultaneously-usable-event conditions. F0405: Too many snap-events. F0406: Too many stub-events. F0407: Too many initialization data. 448 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES F0408: Too large search data (> 16 byte). F0409: Too large search data (> search range). F040a: Too many Linking-event conditions. F04a0: Software break conditions number overflow. F04a1: Not enough memory for emulation. F04a2: Too many partition of bus size. F04a3: Too many execution-event conditions. F04a4: Too many bus-event conditions. A0600: Not enough memory for buffer. 1) There is not enough system memory. Close the applications being executed and the open files. A0601: Not enough resource of operating system. F0b20: This event number can not be used. F0b61: Section Trace event conditions overflow. F0b80: Reset by hardware error. F0c00: Monitor file read error. 1) Necessary files may be damaged. Reinstall the debugger. A0c01: During access of register, CPU did time out. 1) Check the clock signal, etc. The register value may not be correct. A0c02: During access of memory, CPU did time out. 1) Check the HOLD signal, WAIT signal, clock signal, etc. The memory value may not be correct. A0c03: During access of IOR/SFR, CPU did time out. 1) Check the HOLD signal, WAIT signal, clock signal, etc. The IOR value may not be correct. F0c20: Guarded area can not be accessed. F0c21: Memory was unready status. F0c22: Memory unready status was canceled. F0c23: Bus hold under continuation. 1) Check the setting of the target board, or mask the HOLD pin. F0c24: It cannot shift to debug mode. 1) Check the clock signal. This may be caused by a stopped clock or a slow clock. F0c25: Flash macro service ROM was accessed or stepped in. 1) Please perform [Go] execution or CPU reset. F0c26: FLMD terminal is in a write-protected state. 1) FLMD is not in the write-enabled status. Check the status of the FLMD0 and FLMD1 pins. F0c27: Security flag is in a write-protected state. 1) The security flag of the flash memory has disabled writing, block erasure, or chip erasure. Nothing can be written to the flash memory. User's Manual U17246EJ2V0UM 449 APPENDIX D MESSAGES F0c28: Internal RAM is not enough, the writing to flash memory is not made. 1) The internal RAM size is less than 4 KB and flash self-programming cannot be executed. F0c29: The blank check of flash memory failed. F0c2a: The erasing of flash memory failed. F0c2b: The writing of flash memory failed. F0c2c: The internal verification of flash memory failed. F0c2d: Failed in writing flash memory. F0c2e: There is no response from flash macro service. F0c2f : Response from flash macro service is not right. F0c30: Flash I/O register operation prohibition setup needs to be canceled. F0c31: STOP mode under continuation. Can not compulsory break. Please release STOP mode or reset the CPU. F0c32: Please write in flash memory in the single chip mode 0. F0c33: Writing to the on-chip debug reserved area is prohibited. F0c34: Disabling the on-chip debug function is prohibited. F0c40: Status of effective event conditions cannot be changed. F0c41: Coverage test is being executed. F0c42: Monitor has failed in shift in the debugging mode.Please reset the CPU. F0c43: Can not communicate with ICE. Please confirm the power of ICE, connection of the interface cable. 1) The switch setting may be wrong if a desktop computer is used and two or more PC cards are inserted. Check the setting. connected). 2) Check the power to the in-circuit emulator and cable connections The switch setting may be wrong if a desktop computer is used and two or more PC cards are inserted. Check the setting. may have malfunctioned (when IECUBE connected). F0c44: Coverage test is being executed. F0c45: Inside of Power off reset emulation cannot carry out program execution. F0c60: Event before execution cannot be set up other than break conditions. F0c61: Can not register event numbers which can not be used for hardware break. F0c62: Event numbers reserved for hardware breaks can not be used. F0c63: Event link conditions cannot set. F0c64: Too many ROM-emulation-RAM areas. F0c67: Writing of flash memory during block is not made. Or it Or it may have malfunctioned (when IE-V850E1-CD-NW, MINICUBE 450 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES F0c70: DCU cannot be accessed. 1) The device file selection may be incorrect. Select a device file that supports the target chip in Chip Selection in the Configuration dialog box. Check the power to the chip. Check the connection of the signal lines (DCK, DMS, DDI, DDO, and DRSTZ). Check the noise level by a DCK waveform test on the N-Wire Checker (when the IE-70000-MC-NW-A, IE-V850E1-CD-NW is connected). 2) IE may be malfunctioning (when the IECUBE is connected). F0c71: Reset cannot be performed. 1) Check the clock signal. This may be caused by a stopped clock or a slow clock. F0c72: Monitor memory cannot be accessed. 1) Revise the Main OSC value in the Configuration dialog box. Check the setting of main clock in the Configuration dialog box , the noise level by a DCK waveform test on the N-Wire Checker. The problem may also be caused by an internal chip problem (when the is IE-V850E1-CD-NW, IECUBE connected). 2) Revise the Main OSC value in the Configuration dialog box. If this does not solve the problem, IE may be malfunctioning (when the IECUBE is connected). 3) Check the noise level by a DCK waveform test on the N-Wire Checker. The problem may also be caused by an internal chip problem (when the IE-70000-MC-NW-A is connected). F0c73: Monitor execution cannot be performed. 1) Check the noise level by a DCK waveform test on the N-Wire Checker. The problem may also be caused by an internal chip problem (when the IE-70000-MC-NW-A , IE-V850E1-CD-NW is connected). 2) IE may be malfunctioning (when the IECUBE is connected). F0c74: CPU register cannot be accessed. 1) Check the noise level by a DCK waveform test on the N-Wire Checker. The problem may also be caused by an internal chip problem (when the IE-V850E1-CD-NW is connected). 2) The device file selection may be incorrect. Select a device file that supports the target chip in Chip Selection in the Configuration dialog box. If this does not solve the problem, the IE may be malfunctioning (when the IECUBE is connected). F0c75 : Monitor has failed in shift in the debugging mode. Please reset the CPU. F0c76 : Initial state at the time of DCU access start is unusual. 1) Initial state at the time of DCU access start is unusual (does not start and remains in the reset state). Check the connection of the signal lines (DCK, DMS, DDI, DDO, and DRSTZ). Check the noise level by a DCK waveform test on the N-Wire Checker (when the IE-V850E1-CD-NW is connected). 2) The device file selection may be incorrect. Select a device file that supports the target chip in Chip Selection in the Configuration dialog box. If this does not solve the problem, the IE may be malfunctioning (when the IECUBE is connected). User's Manual U17246EJ2V0UM 451 APPENDIX D MESSAGES F0c77 : DCU access is unusuall. 1) DCU access is unusuall (verify error). Check the connection of the signal lines (DCK, DMS, DDI, DDO, and DRSTZ). Check the noise level by a DCK waveform test on the N-Wire Checker (when the IE-V850E1-CD-NW is connected). 2) IE may be malfunctioning (when the IECUBE is connected). F0c78: Failed in reading of trace data. F0ca0: Can not communicate with ICE. Please confirm the power of ICE, connection of the interface cable, or I/O address of the PC interface board.(V850) Error occurred inside debugger. (IECUBE) 1) Can not communicate with simulator. Check the power of the simulator, cable connections, and setting of the interface board etc. F0ca1: Monitor file not found. 1) Necessary files may be damaged. Reinstall the debugger. F0ca2: This device file does not include the on-chip debug information. 1) An attempt was made to start with a device file not supporting on-chip debugging. The device file may be old. Install the latest device file (when the IE-V850E1-CD-NW, MINICUBE is connected). 2) IE may be malfunctioning (when the IECUBE is connected). F0ca3: Unsupported information is included in the on-chip debug information in the device file. 1) An unknown flag is included in the on-chip debug information of the device file.The exec module may be old. Install the latest exec module. F0ca4 : This device file does not include the IECUBE information. 1) An attempt was made to start with a device file not supporting IECUBE. The device file may be old. Install the latest device file. F0caf: Trace block can not be stepped over. (2) X1000~ A1000: Failed in initializing ICE. A1001: No entry exists for specified number. A1002: Can not relocate internal RAM. F1003: Illegal relocation address. F1004: Illegal condition. A1005: Invalid attribute. F1006: Illegal address. A1007: Not enough memory on ICE. A1008: Not enough memory for tables. 1) There is not enough system memory. Close the applications being executed and the open files. A1009: Already initialized. 452 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES A100a: Not initialized. F100b: User program is running. F100c: Different bus size has been already specified. F100d: Too large bus size. F100e: Too large bus partition size. W100f: Target is not turned on. F1010: Illegal map range. F1011: Failed in setting internal ROM and RAM. F1012: This feature is not supported. F1013: No terminal name. W1014: Data is not exist. A1015: Programmable-IOR does not exist. F1016: Programmable-IOR does not movable. 1) Necessary files may be damaged. Reinstall the latest device file. F1017: I/O Protect mapping is possible a target attribute only. F1018: Illegal Internal ROM size. F101a: Specified Simulator configuration file was not found. F101b: Simulator configuration file was not specified. F101c: Illegal Simulator configuration file. A10ff: Can not communicate with ICE. A1dbe: Error occurred inside debugger. (3) X2000~ F2000: Illegal IOR name. [V850] Illegal SFR name. [78K] A2001: Illegal address. F2002: User program is running. F2003: Illegal IOR number. [V850] Illegal SFR number. [78K] F2004: Illegal bit number. W2005: IOR of Read Protect attribute was specified. [V850] SFR of Read Protect attribute was specified. [78K] F2006: Hidden IOR was specified. [V850] Hidden SFR was specified. [78K] F2007: IOR of ban read or write was specified. [V850] SFR of ban read or write was specified. [78K] User's Manual U17246EJ2V0UM 453 APPENDIX D MESSAGES F2008: IOR not existing was specified. [V850] SFR not existing was specified. [78K] A2009: Device file is damaged or error is in file. F200a: Illegal value specified for IOR. [V850] Illegal value specified for SFR. [78K] A200b: Can not copy. A200c: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. W200d: No initialize data for IOR. [V850] No initialize data for SFR. [78K] F200e: IOR area can not be accessed. [V850] SFR area can not be accessed. [78K] A20ff: Can not communicate with ICE. A2222: Illegal condition. (4) X3000~ F3000: No mapped address was accessed. 1) The allocation addresses of the program and the addresses of the debugger may not match. Set the mapping to the external memory in the Configuration dialog box according to the allocation addresses specified in the link directive file on compilation. When mapping to external memory has been executed, change the register values necessary for accessing the external memory using the IOR/SFR window or Hook Procedure before download. F3001: Memory has different value. F3002: Illegal start address. F3003: Illegal end address F3004: Illegal start address and end address. F3005: Illegal condition. F3006: User program is running. F3007: Verification error. F3008: No condition specified. F3009: Parameter size does not align with access size alignment. F300a: Specified address does not align with access size alignment. F300b: Source address does not align with access size alignment. F300c: Destination address does not align with access size alignment. F300d: Illegal end address. F300e: Different access size in specified area. F300f: Different access size both in source and destination areas. 454 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES F3010: Different access size in destination area. F3011: Different access size, source & destination. A3012: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. F3013: Failed in writing DMM. F3014: Oveflowed mapping area. F3015: Processing was interrupted. F3016: This feature is not supported. A30ff: Can not communicate with ICE. (5) X4000~ F4000: Can not delete specified event. 1) The specified event cannot be deleted as it is being used under another condition. Invalidate it for other usages before deleting. F4001: Illegal table number. F4002: Illegal start address. F4003: Illegal end address. F4004: Illegal status. F4005: Illegal data. F4006: Specified event number has been already used. F4007: Too many same events are registered. F4008: Specified event has not been registered. F4009: Illegal data size. F400a: Illegal mode. F400b: Setting value is inaccurate. F400c: Event link conditions cannot be used for section trace conditions. F400d: Too many identical events are registered (>= 32767). F400e: Specified event condition does not exist. F400f: Illegal event link condition. F4010: Function not found. A4011: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. F4012: Timer is being disabled. W4013: Access size is different from its mapped bus size. F4014: Can not use software break. F4015: Can not use event condition specifying address range. User's Manual U17246EJ2V0UM 455 APPENDIX D MESSAGES F4016: Can not change event condition. F4017: Can not access word at odd address. A4018: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. F4019: This feature is not supported. F401a: No Event. F401b: Can not use tag-event. W401c: Software break can not be set on this area. F401d: Start event and end event of timer are not made to the same setup. F401e: Too many trace-events. F401f: Path count cannot be set up. F4020: Address range cannot be set up in event before execution. F4021: Event conditions number overflow. F4022: Software DMM conditions number overflow. F4023: Real-time call conditions number overflow. F4024: Software break call conditions number overflow. F4025: Illegal snap condition. F4026: Too many event conditions cannot be set as Phase1 and Phase2 of event link conditions. F4027: Software break conditions number which can be set as internal ROM was overflow. F4318: Illegal memory bank setting. (6) X5000~ A5000: Illegal device file type. A5001: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. A5002: Can not open device file. A5003: Reading of device file went wrong. A5004: Can not close device file. A5005: Illegal device file format. 1) Necessary files may be damaged. Reinstall the device file. A5006: Failed in initializing ICE. A5007: Device file has broken or error is in a file. F5008: Can not open device file. 1) Necessary files may be damaged. Reinstall the device file. F5009: Can not open ie703000.ie. 456 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES F500a: Specified device file is illegal version. 1) Necessary files may be damaged. Reinstall the device file. W500b: Specified device file does not relocate IRAM. A500c: Failed in reading expc.ini. A500d: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. W500e: No tag data which it was going to refer to device file. A5300: Illegal device file type. A5301: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. A5302: Can not open database file. 1) Necessary files may be damaged. Reinstall the debugger and device file. A5303: Reading of database file went wrong. A5304: Can not close database file. A5305: Illegal database file format. 1) Necessary files may be damaged. Reinstall the debugger, and device file. A5306: Database information has been already initialized. A5307: Database information does not exist. F5308: Can not open specified database file. 1) Necessary files may be damaged. Reinstall the debugger. F5309: Specified database file is illegal version. 1) Necessary files may be damaged. Reinstall the debugger, and the device file. (7) X6000~ F6000: Current function does not exist. F6001: Illegal symbol name. F6002: Illegal condition. F6003: Illegal function name. F6004: Overflowed output buffer size. F6005: Illegal expression. (8) X7000~ F7000: Illegal mode. F7001: User program is running. F7002: User program has been stopped. F7003: Trace enabled. User's Manual U17246EJ2V0UM 457 APPENDIX D MESSAGES F7004: Trace memory is not set. F7005: Function return address does not exist, can not do step execution. W7010: No source information exists. W7011: Unknown result of step execution. A7012: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. A70fe: Bus hold error. 1) CPU is in the bus-hold status. Reset the debugger. A70ff: Can not communicate with ICE. F7801: End waiting state of step execution was canceled. F7802: End waiting state of step execution was canceled. F7f00: Aborted step execution. F7f02: Suspended step execution. A7f03: Failed in canceling RUN/STEP. F7f04: Can not execute non-mapped area. F7f05: This feature is not supported. (9) X8000~ F8000: Specified file was not found. F8001: Illegal line number. F8002: Current information is not set. F8003: Illegal address. F8004: This feature is not supported. (10) X9000~ A9000: Specified register symbol does not exist. A9001: Specified register symbol ID does not exist. F9002: Illegal value. A9003: Illegal condition. A9004: Too large register size. F9005: This feature is not supported. (11) Xa000~ Fa001: Illegal expression. Fa002: Start address is bigger than the end address. Fa003: Illegal source path. 458 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES Fa004: Too long expression. Aa005: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. Fa006: Illegal argument. Fa007: Illegal program number. Fa008: Source path is not set. Fa009: File not found. Fa00a: Can not open file. 1) The file is damaged or does not exist. Recreate the file. Aa00b: Can not close file. Aa00c: Failed in reading file. 1) The file is damaged or does not exist. Recreate the file. Fa00d: Not source file of load module. Fa00e: Illegal line number. Fa00f: Variable does not exist. Aa010: Can not communicate with ICE. Fa011: Can not access register. Fa012: Can not access memory. Aa013: Reading of file went wrong. Fa014: It was going to open the binary file. Fa015: Can not get temporary path. 1) The disk is full. Delete or move unnecessary files and increase the available memory in the disk. Fa016: Can not create temporary file. 1) The disk is full. Delete or move unnecessary files and increase the available memory in the disk. Fa017: Can not remove temporary file. Fa020: This feature is not supported. Fa021: Symbol assigned to register cannot be specified. (12) Xb000~ Fb000: Illegal command line. Fb001: Program information does not exist in specified load module file. Fb002: File not found. Fb003: Function not found. Fb004: Selected load module different from kind (Chip) was loaded. Fb005: Symbol not found. 1) The address could not be found. Specify a location holding address information. User's Manual U17246EJ2V0UM 459 APPENDIX D MESSAGES Fb008: Illegal expression. Ab009: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. Fb00a: Illegal symbol in load module file. Fb00b: Current program does not exist. Fb00c: Current file does not exist. Ab00d: Current function does not exist. Ab00e: Current line does not exist. Ab00f: Tag not found. Ab010: Failed in loading symbol table. Ab011: Illegal line number. Fb012: Too large line number. Ab015: Reading of file went wrong. 1) The file is damaged or does not exist. Recreate the file. Ab016: Can not open file. 1) The file is damaged or does not exist. Recreate the file. Ab017: Failed in writing file. 1) The file is damaged or does not exist. Recreate the file. Ab019: Reading of file went wrong. Ab01a: Can not close file. Fb01b: Too long load module file name. Ab01c: Too many entries of the task kind. Fb01d: Address not found. Wb01e: No debug information (not compiled in Debug Build mode). Fb01f: Can not find structure member. Fb020: Can not find value. Fb021: No debug information exists in load module file. 1) To create a load module with appended debug information, execute build in build mode of Debug Build. Fb022: Illegal line number. Ab023: Current stack frame is not active. Ab024: Different section. Fb026: Too many array dimensions (> 4). Fb027: Found end of file. 1) The specified file may be damaged. Recreate the file. Fb028: This feature is not supported. Fb029: Illegal address. 460 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES Ab02a: Can not communicate with ICE. Fb02b: Can not stack trace with current PC value. Fb02c: Too many blocks for one function. Fb02d: Illegal argument. Fb02e: The file does not exist in the SOURCE PATH. 1) On stopping the program, the source that the debugger tried to display could not be found. Check if the path connects to the source in the Debugger Option dialog box, or check if the source is in the same directory as the out file. Refer to the Assemble window on which the error message is displayed, and check if the corresponding path connects. Fb02f: Information has been deleted because of optimization. Ab030: Monitor timed out. 1) Check the power of the in-circuit emulator, cable connections, and setting of the interface board and restart the debugger. Ab031: Already set in memory. Ab032: Out of scope. Ab033: LP is not stored. Fb034: Return execution from present PC position cannot be performed. Fb037: Too Many Line-Numbers Information. Fb038: Compiler version mismatch. 1) Recreate the load module with the latest compiler. Ab039: Failed in loading debug information. Ab03a: No more section information. Fb040: Specified file is not load module. 1) This is not a linker output file. Source debug cannot be executed with the load module before output from the linker. Specify the load module output from the linker. Ab041: Too many files in load module to download. Wb042: Symbol module is not initialized. Fb32e: Illegal port number. Fb32f: Illegal port name. Fb330: Illegal port position. Fb331: Illegal increment number. Fb332: Port for memory bank is not set. Fb333: Illegal bank number. Fb334: Area for memory bank is not set. Wb335: Too long symbol name. User's Manual U17246EJ2V0UM 461 APPENDIX D MESSAGES (13) Xc000~ Fc001: Can not open file. 1) The file is damaged or does not exist. Recreate the file. Ac002: Can not close file. Ac003: Reading of file went wrong. 1) The file is damaged or does not exist. Recreate the file. Ac004: Reading of file went wrong. Fc005: Illegal file type. Fc006: Kind (Chip) of load module is illegal. Fc007: Specified file is not load module. 1) This is not a linker output file. Source debug cannot be executed with the load module before output from the linker. Specify the load module output from the linker. Fc008: Specified load module file (ELF) is old version. [V850] Specified load module file (COFF) is old version. [78K] Ac009: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. Fc00a: No mapped address was accessed. Fc00b: Load module is not loaded. Fc00c: Illegal argument. Fc00d: User program is running. Fc00e: User program is being traced. Fc00f: Interrupted. Ac010: Can not communicate with ICE. Fc011: Illegal load module file format. Fc012: Check sum error. Fc013: Too wide address range to upload (> 1M byte). Fc014: Failed in writing file. 1) The file is damaged or does not exist. Recreate the file. Fc015: Illegal program number. Fc016: Load information is full. Wc017: Symbol information is duplicated, please reset symbols. Fc018:Specified file is not load module. 1) This is not a linker output file. Source debug cannot be executed with the load module before output from the linker. Specify the load module output from the linker. Fc019: Failed in writing memory. 462 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES Wc01a: BSS area is assigned to non-mapped area. 1) When the program is executed, a non-map break may occur. Either allocate the BSS area to the internal RAM by using a CA link directive, or map the emulation memory or target memory to the BSS area using the Configuration dialog box of the debugger. Fc01b: Programmable-IOR address not specified. 1) Necessary files may be damaged. Reinstall the debugger. Wc01c: Programmable IOR address mismatch. 1) Necessary files may be damaged. Reinstall the debugger. Wc01d: Selected load module different from kind (Chip) was loaded. Fc101e: .Flash erase is not supported on IECUBE. Fc100: This feature is not supported. (14) Xd000~ Ad000: Error occurred inside debugger. Ad001: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. Ad002: Failed in reading initialization file (expc.ini). Ad003: ICE is not connected. Fd004: Can not find Dynamic Link Library. (15) Xe000~ Fe000: Illegal argument. Fe001: Illegal start address. Fe002: Illegal end address. Fe003: Too large size. Fe004: Can not open file. 1) The file is damaged or does not exist. Recreate the file. Fe005: Failed in reading file. 1) The file is damaged or does not exist. Recreate the file. Fe006: Reading of file went wrong. Fe007: Failed in writing file. 1) The file is damaged or does not exist. Recreate the file. Ae008: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. Fe009: Illegal file format. Fe00a: Verification error. User's Manual U17246EJ2V0UM 463 APPENDIX D MESSAGES Fe010: This feature is not supported. (16) Xf000~ Af000: Not enough memory. 1) There is not enough system memory. Close the applications being executed and the open files. Ff000: Not enough memory. Ff001: [XXX] not found. Wf002: Not found [XXX]. Search from the beginning? Wf003: Already exceed search region. Ff004: Missing parameter. Ff005: Illegal function name. Ff006: Illegal number. Ff007: Start address is bigger than end address. Ff008: Illegal symbol or expression. Ff009: [XXX] This file is illegal type. Ff100: Disk cannot write or full. Ff101: File not found. Ff102: File not Create. Ff103: Old project file version. Ff104: Illegal project file format. Ff105: This file is a project file for [XXX].Please select a correct file. Wf106: CPU in the Project File was Changed. You must exit the debugger for the new CPU. Do you exit the Debugger? Wf107: CPU in the Project File was Changed. Do you start the Debugger with this CPU? Wf108: Selected project file different [YYY] from chip [XXX] was opened. Does it open, although the chip cannot be changed? Wf109: Project Manager cannot be used with the debugger of this version. Please use PMplus. Wf200: No difference encountered. Ff201: Memory mapping error. Ff202: Verify error. 1) External memory could not be accessed, as it is not set. Change the register values necessary for accessing the external memory using the IOR/SFR window or Hook Procedure before download . Wf203: When a program is running, while rewriting a memory, program execution stops for a moment. Do you wish to rewrite a memory? Wf300: Would you like to save the changes made in [XXX]? Ff301: The symbol being used on the event condition can't be evaluated. Wf302: Delete: [XXX] 464 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES Wf303: [XXX] is edited. Delete: [YYY]? Wf304: [XXX] is edited. Save: [YYY]? Wf305: [XXX] is already exist. Do you replace it? Ff306: This name is too long. Ff307: There is the same name in other kinds. Ff308: An address can't be omitted. Ff309: Illegal address mask. Ff30a: Illegal data mask. Ff30b: Illegal ext probe mask. Ff30c: Illegal ext probe data. Ff30d: Illegal pass count. Ff30e: Illegal register name. Ff30f: Illegal register bank. Ff310: Illegal delay count. Wf311: Only one [XXX] can be enabled. Do you make this [YYY] to enable? Ff312: [XXX] is already there. Ff313: Event number already exist. Ff314: Event name is not set. Ff315: [XXX] is already there. Ff316: Max number of enabled [XXX] event is over. Please disable other enabled [YYY] event. Ff317: Max number of set event is over. Ff31e: Illegal start address. Ff31f: Illegal end address. Ff322: Illegal count rate. Ff323: Illegal time out break count. Ff324: Section and Qualify can be specified at the same time. Wf325: User program is running. Do you want to stop user program for a moment and set it? Wf326: User program is running. Do you want to stop user program for a moment and delete it? Ff350: There is a phase which event are not in the middle. Ff351: The same event is contained in Link and Disable. Ff352: An event isn't specified. Ff357: AND event is in Phase. Ff400: Coverage mapping error. Wf401: Clear coverage? Ff500: Illegal symbol. Ff501: Illegal value. User's Manual U17246EJ2V0UM 465 APPENDIX D MESSAGES Ff502: Illegal parameter. Ff503: Max number of symbol is over. Ff504: This variable cannot be set as a break. 1) Break cannot be set for the following variables. - Local variables, static variables - Array variables, member variables of structures/unions - Register/peripheral I/O registers [V850] /SFR [78K] - Variable expressions Wf600: Save project file? Wf601: When connecting the target system, please turn on the target system. 1) When a target is not connected, simply click the 466 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES Af604 : Incorrect ID Code. Abort the debugger. 1) This may be caused by the following (when the IE-V850E1-CD-NW is connected) - The ID code is incorrect. -> Input the correct ID code. - The internal flash memory is in the write mode because the FLMD0 pin is high. -> Make the FLMD0 pin low. - The emulator connection prohibition mode is set because the ID code (bit 7 of address 0x79) is 0. ->Erase the internal flash memory once. 2) This may be caused by the following (when the MINICUBE is connected). - The ID code is incorrect. -> Input the correct ID code. - The internal flash memory is in the write mode because the FLMD0 pin is high. -> Make the FLMD0 pin low. - The emulator connection prohibition mode is set because the ID code (bit 0,1 of address 0x84) is 0. ->Erase the internal flash memory once by flash writer. Ff605: Please check connection with the target board. 1) Check the connection of the target connector (TC). If a target is not connected, review the Target setting in the Configuration dialog box. Ff606: Please check connection with the target board, and power on it. 1) Check the target power supply. Configuration dialog box. Wf607 : Please check connection of the exchange adapter. 1) Check the connection of the exchange adapter (EA). Recommend wearing of the exchange adapter, if the target is not connected. Ff608 : Please disconnect the target board. 1) A current may flow from the internal power supply to the target. Disconnect the target connector (TC) from the conversion adapter (EA). Review the setting in the Configuration dialog box if the target is not connected. Ff609: Please power off the target board, and disconnect it. Wf700: Do you want to download Load Module File? Wf701: Do you load symbol information only? Wf800: Configuration of Memory Bank is not set. Wf801: BANK address must be in target memory. Ff802: All events are deleted. because the use of external probe was changed. Ff803: This event address is invalid on current configuration. Ff804: Invalid PC value. Ff805: Cannot set temporary break on this address. Ff806: External data is being used by Debugger. If a target is not connected, review the Target setting in the User's Manual U17246EJ2V0UM 467 APPENDIX D MESSAGES Ff900: Illegal I/O port name. Ff901: Memory mapping error. 1) The specification of the address is illegal. Check the addresses that can be specified in the Add I/O Port dialog box. Ff902: Illegal access size. Ff903: Illegal access type. Ff904: There is the same name. Wf905: [XXX] is already exist. Do you replace it? Wf906: Would you like to register the change made in [XXX]? Ffa00: The [XXX] function of current program on PC position not found. 1) The symbol specified in main() label: in the Debugger Option dialog box could be found. Set a symbol of the main routine of the program. Default is _main. Ffa01: The line information on PC position not found. 1) The source file corresponding to program counter (PC) value when the program was stopped could not be found. The following reasons are possible. -The source file exists in a location that the source path does not connect to. -The program stopped where the source files, such as library or RX, do not exist. -The program looped, jumped to an address that is not used by the program, and stopped there. Wfb00: User program is running. Do you want to stop user program? 1) (17) X10000~ E10000: Can't allocate momory. 1) Could not secure the memory required for processing. Close other applications, or increase virtual memory in Windows to secure the required memory. E10001: Can't open file. 1) Could not open to specified file. Check if the file exists, the file attributes, and the disk capacity. 468 User's Manual U17246EJ2V0UM APPENDIX D MESSAGES E10002: Illegal file format. 1) Specified file format is incorrect. Check if the specified file attributes (Open dialog box) are correct, and check also the file contents. E10003: Can't write file. 1) Could not write to specified file. Check if the file exists, the file attributes, and the disk capacity. E10180: A user model file is not specified. 1) User model file is not specified in configuration file loaded in user model. Specify the user model file. E10181: Can't open the user model file. 1) Could not open specified user model file, or MakeUserModel function does not exist. Check if the file exists, the file attributes, and if the MakeUserModel function exists. E10200: The pin name is invalid. 1) Specified pin name is not correct (does not exist in target device). Specify a pin name that exists in the target device. E10440: Program is running. 1) Could not perform processing during program execution in the Timing Chart window. Stop program execution and then perform processing. E10500: Correspondence of loop is not correct. 1) Loop start and loop stop correspondence in the Signal Data Editor window is not correct. Perform modification so that loop start and loop stop correspondence is correct. E10501: The data number exceeded maximum. 1) Data number (line number) exceeded maximum (1,048,576) in the Signal Data Editor window. Perform adjustment so that the data number does not exceed the maximum. E10502: The pin name is invalid. 1) Pin name specified during pin specification in the Signal Data Editor window is not correct (does not exist in target device). Specify a pin name that exists in the target device. E10503: Illegal loop count. 1) The loop count in the Loop dialog box is an illegal value or out of the valid range (0 to 99). Specify a correct value. E10700: The pin name is invalid. 1) Pin name specified during pin specification in the I/O Panel window is not correct (does not exist in target device). Specify a pin name that exists in the target device. E10702: Illegal thickness of line. 1) Line thickness specified during style setting in the I/O Panel window is an illegal value or is outside the valid range (1 to 100). User's Manual U17246EJ2V0UM 469 APPENDIX D MESSAGES E10703: Illegal hold time. 1) Hold time specified during input-related part setting in the I/O Panel window is an illegal value or is outside the valid range (0.001 to 999). E10704: Illegal muximum input. 1) Maximum input value specified during level gauge setting in the I/O Panel window is an illegal value or is outside the valid range (1 to 65535). Specify a correct value. E10710: A bitmap path is not specified. 1) Either active or inactive bitmap, or both not specified during bitmap addition in the I/O Panel window. Specify bitmap file. E10711: A bitmap path is invalid. 1) Bitmap file specified during bitmap addition in the I/O Panel window is not correct. Check if the file exists and file the attributes. E10740: Program is running. 1) Could not perform processing because program is being executed in the I/O Panel window. Stop program execution and then perform processing. E10800: The interface address is invalid. 1) Interface address set in the Simulator Option dialog box is not correct. Set a correct value. E10900: Illegal baudrate value. 1) Baudrate value specified in the Format (UART) dialog box is not a correct value. Refer to the user's manual of the device and specify an integer within the valid range. E10901: Illegal transfer clock value. 1) Transfer clock value specified in the Format (CSI) dialog box is not a correct value. Refer to the user's manual of the device and specify an integer within the valid range. E10902: Illegal data bit length. 1) Data bit length specified in the Format (UART) dialog box or the Format (CSI) dialog box is outside valid range (integer equal to or lower than 32). Specify an integer within the valid range. E1ffff: The internal error occurred. 1) The internal error occurred. Notify the manufacturer. 470 User's Manual U17246EJ2V0UM APPENDIX E INDEX APPENDIX E INDEX A About dialog box ... 295 Active status and static status ... 79 Add I/O Port dialog box ... 221 Add Watch dialog box ... 182 Address move dialog box ... 171 Assemble Search dialog box ... 169 Assemble window ... 165 B break break types ... 44 Breakpoint setting ... 45 setting break to variable ... 46 Break dialog box ... 275 Browse dialog box ... 299 Conditional trace ... 60 Configuration dialog box ... 132 Connected parts types ... 108 Console window ... 296 Contents saved to project file ... 75 Context menu ... 116 Coverage Search dialog box ... 251 Coverage window ... 247 Coverage-Address dialog box ... 254 Coverage-Clear dialog box ... 253 Coverage-Condition Setting dialog box ... 255 Coverage-Efficiency View dialog box ... 257 Customize dialog box ... 380 C callback procedure ... 390 Change Watch dialog box ... 185 character set ... 435 Come Here ... 48 command ... 296 address ... 393 assemble ... 394 batch ... 395 breakpoint ... 396 command list ... 387 dbgexit ... 398 download ... 399 extwin ... 400 finish ... 401 go ... 402 help ... 403 hook ... 404 inspect ... 405 jump ... 406 map ... 407 mdi ... 408 memory ... 409 module ... 410 next ... 411 refresh ... 412 register ... 413 reset ... 414 run ... 415 step ... 416 stop ... 417 upload ... 418 version ... 419 watch ... 420 where ... 421 wish ... 422 xcoverage ... 423 xtime ... 424 xtrace ... 425 Command reference ... 386 D Debug function list ... 36 Debugger Option dialog box ... 139 Delay Count dialog box ... 246 Delay trigger ... 244 Delay trigger trace ... 61 Disable condition ... 273 Displaying event details ... 260 DMM dialog box ... 206 download ... 39 Download dialog box ... 149 Download Function / Upload Function ... 39 drag & drop function ... 83 E Edit Colors dialog box ... 382 Edit mode ... 344 emulation ROM ... 134 Entry Bitmap dialog box ... 379 Environment Setting File Load Dialog Box ... 291 Environment Setting File Save Dialog Box ... 289 Errors ... 444 Event dialog box ... 265 Event function ... 65 Event manager area ... 67 Number of enabled events ... 68 Setting event ... 66 Various event conditions ... 65 Event Link dialog box ... 272 Event Manager ... 259 Event manages ... 68 Event Setting Status (Event Mark) ... 157 Exit Debugger dialog box ... 294 Expansion window ... 427 Expressions ... 437 Extended Option dialog box ... 136 F Font dialog box ... 297 Font dialog box (Simulator Block) ... 383 Format (CSI) dialog box ... 333 Format (UART) dialog box ... 331 User's Manual U17246EJ2V0UM 471 APPENDIX E INDEX G -g option ... 23 H hook procedure ... 391 I I/O Panel window ... 338 input conventions ... 435 Installing ... 24 Interface address ... 325 IOR Select dialog box ... 218 IOR window ... 213 Parts Matrix Led Properties ... 365 Parts Segment LED Properties ... 360 pick up ... 239 Pin I/O Function ... 86 PM+ ... 31 Point mark area ... 157, 166 program code ... 158 Program execution function ... 47 project file ... 74, 294 Project File Load dialog box ... 147 Project File Save dialog box ... 145 Pull up/Pull down dialog box ... 371 Q Qualify trace ... 61, 244 Quick Watch dialog box ... 179 J jump function ... 80 R Range of Radixes ... 439 Register Select dialog box ... 211 Register window ... 208 reset ... 293 Reset Debugger dialog box ... 293 right click menu ... 116 RRM function ... 73 Run-Break event ... 57 L Level Gauge Properties ... 354 linking window ... 82 Load Module List dialog box ... 154 Load/Save Function ... 74 Local Variable window ... 187 Loop dialog box ... 308 M Main window ... 117 mapping ... 134 Mapping settings ... 37 Memory Compare dialog box ... 202 Memory Compare Result dialog box ... 204 Memory Copy dialog box ... 200 Memory Fill dialog box ... 198 Memory manipulation function ... 53 Memory Search dialog box ... 195 Memory window ... 192 Menu bar ... 118 Messages ... 444 Mixed display mode Source window ... 42 Trace window ... 59 O Object Properties ... 373 Open dialog box ... 384 Operating Environment ... 22 Operation after CPU reset ... 110 Operators ... 438 P Panel Function ... 107 Parts Button Properties ... 346 Parts Buzzer Properties ... 368 Parts Key Properties ... 351 Parts Led Properties ... 358 Parts List dialog box ... 377 S Save As dialog box ... 385 Search Data dialog box ... 318 Section trace ... 61, 244 Select Pin dialog box ... 316 Serial I/O Function ... 99 Serial log data file (*.log) ... 100 Serial send data file (*.ser) ... 102 Serial window ... 326 Setting debugging environment ... 37 setting file ... 78 Setting mapping ... 37 Signal Data Editor window ... 301 Simulation mode ... 109 Simulator Option dialog box ... 324 Snap Shot dialog box ... 277 Source Search dialog box ... 161 Source Text move dialog box ... 163 Source window ... 156 Stack trace display function ... 52 Stack window ... 189 Standard I/O Buffer Size dialog box ... 323 Standard I/O Function ... 92 Standard I/O window ... 320 Start From Here ... 48 Startup option ... 26 Startup Routine ... 142 Status Bar ... 129 Stub dialog box ... 282 Symbol To Address dialog box ... 172 472 User's Manual U17246EJ2V0UM APPENDIX E INDEX T Timer dialog box ... 223 Timer function ... 57 Timer Result dialog box ... 226 Timetag ... 137, 229 Timing Chart window ... 310 Tool bar ... 126 Tool bar (simulator block) ... 128 Trace Data Select dialog box ... 238 Trace dialog box ... 243 Trace function ... 58 trace memory ... 58 Trace move dialog box ... 241 Trace Search dialog box ... 233 Trace window ... 227 Types of Messages ... 445 U Unconditional trace ... 60 Uninstalling ... 24 Upload ... 40 Upload dialog box ... 152 V Verify check ... 137 view file ... 77 View File Load dialog box ... 287 View File Save dialog box ... 284 W Watch function ... 49 Watch window ... 174 window list ... 112 window reference ... 111 User's Manual U17246EJ2V0UM 473 |
Price & Availability of SM789234-B
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |