 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PHOTOCOUPLER PS9587,PS9587L1,PS9587L2,PS9587L3 HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN DIP HIGH-SPEED PHOTOCOUPLER NEPOC FOR CREEPAGE DISTANCE OF 8 mm DESCRIPTION The PS9587, PS9587L1, PS9587L2 and PS9587L3 are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and a signal processing circuit on the output side on one chip. The PS9587L1 and PS9587L2 are designed specifically for long creepage-distance as well as high common mode transient immunity (CMR) and high speed digital output type. Consequently, they are suitable for high speed logic interface that needs long creepage-distance (8 mm) on mounting. The PS9587L1 is lead bending type for long creepage distance. The PS9587L2 is lead bending type for long creepage distance (Gull-wing) for surface mount. The PS9587L3 is lead bending type (Gull-wing) for surface mounting. Series FEATURES * Long creepage distance (8 mm MIN.: PS9587L1, PS9587L2) * High common mode transient immunity (CMH, CML = 15 kV/ s MIN.) * High isolation voltage (BV = 5 000 Vr.m.s.) * High-speed response (10 Mbps) * Pulse width distortion ( tPHL * Open collector output * Ordering number of tape product: PS9587L2-E3: 1 000 pcs/reel : PS9587L3-E3: 1 000 pcs/reel * Pb-Free product * Safety standards * UL approved: No. E72422 APPLICATIONS * FA Network * Measurement equipment * PDP Document No. PN10678EJ04V0DS (4th edition) Date Published September 2009 NS The mark PS9587,PS9587L1,PS9587L2,PS9587L3 PACKAGE DIMENSIONS (UNIT: mm) DIP Type Lead Bending Type (Gull-wing) For Surface Mount 2 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 Lead Bending Type For Long Creepage Distance Lead Bending Type For Long Creepage Distance (Gull-wing) For Surface Mount Data Sheet PN10678EJ04V0DS 3 PS9587,PS9587L1,PS9587L2,PS9587L3 PHOTOCOUPLER CONSTRUCTION Parameter Air Distance (MIN.) Outer Creepage Distance (MIN.) Isolation Distance (MIN.) PS9587, PS9587L3 7 mm 7 mm 0.4 mm PS9587L1, PS9587L2 8 mm 8 mm 0.4 mm FUNCTIONAL DIAGRAM MARKING EXAMPLE 4 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 ORDERING INFORMATION Part Number Order Number Solder Plating Specification PS9587 PS9587L1 PS9587L2 PS9587L3 PS9587L2-E3 PS9587L3-E3 PS9587-V PS9587L1-V PS9587L2-V PS9587L3-V PS9587L2-V-E3 PS9587L3-V-E3 PS9587-AX PS9587L1-AX PS9587L2-AX PS9587L3-AX PS9587L2-E3-AX PS9587L3-E3-AX PS9587-V-AX PS9587L1-V-AX PS9587L2-V-AX PS9587L3-V-AX PS9587L2-V-E3-AX PS9587L3-V-E3-AX Embossed Tape 1 000 pcs/reel Magazine case 50 pcs DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) Embossed Tape 1 000 pcs/reel Pb-Free (Ni/Pd/Au) Magazine case 50 pcs Packing Style Safety Standard Approval Standard products (UL, CSA, BSI, SEMKO, NEMKO, DEMKO, FIMKO approved) Application Part Number*1 PS9587 PS9587L1 PS9587L2 PS9587L3 PS9587L2 PS9587L3 PS9587 PS9587L1 PS9587L2 PS9587L3 PS9587L2 PS9587L3 *1 For the application of the Safety Standard, following part number should be used. Data Sheet PN10678EJ04V0DS 5 PS9587,PS9587L1,PS9587L2,PS9587L3 ABSOLUTE MAXIMUM RATINGS (TA = 25 C, unless otherwise specified) Parameter Diode Forward Current*1 Reverse Voltage Detecto r Symbol IF VR VCC Ratings 30 5 7 Unit mA V V Supply Voltage Output Voltage Output Current Power Dissipation Isolation Voltage *3 *2 VO IO PC BV TA Tstg 7 25 40 5 000 40 to +85 55 to +125 V mA mW Vr.m.s. C C Operating Ambient Temperature Storage Temperature *1 Reduced to 0.3 mA/ C at TA = 25 C or more. *2 Applies to output pin VO (Collector pin). Reduced to 1.5 mW/ C at TA = 65 C or more. *3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output. Pins 1-4 shorted together, 5-8 shorted together. RECOMMENDED OPERATING CONDITIONS (TA = 25 C) Parameter High Level Input Current Low Level Input Voltage Supply Voltage TTL (RL = 1 k , loads) Pull-up Resistance Symbol IFH VFL VCC N RL 330 MIN. 6.3 0 4.5 5.0 TYP. 10 MAX. 12.0 0.8 5.5 5 4k Unit mA V V 6 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 ELECTRICAL CHARACTERISTICS (TA = 40 to +85 C, unless otherwise specified) Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Current Low Level Output Voltage *2 Symbol VF IR Ct IOH VOL ICCH ICCL L) IFHL Conditions IF = 10 mA, TA = 25 C VR = 3 V, TA = 25 C VF = 0 V, f = 1 MHz, TA = 25 C VCC = VO = 5.5 V, VF = 0.8 V VCC = 5.5 V, IF = 5 mA, IOL = 13 mA VCC = 5.5 V, IF = 0 mA, VO = Open VCC = 5.5 V, IF = 10 mA, VO = Open TA = 25 C VCC = 5 V, VO = 0.8 V, RL = 350 MIN. 1.4 TYP.*1 MAX. 1.65 1.8 10 30 1 0.2 5 9 150 100 0.6 8 11 3.3 1.5 5 Unit V A pF A V mA mA mA High Level Supply Current Low Level Supply Current Coupled Threshold Input Current (H Isolation Resistance Isolation Capacitance Propagation Delay Time (H L) *3 RI-O CI-O tPHL VI-O = 1 kVDC, RH = 40 to 60%, TA = 25 C V = 0 V, f = 1 MHz, TA = 25 C VCC = 5 V, TA = 25 C 10 11 0.9 35 5 75 100 pF ns VTHHL = VTHLH = 1.5 V, tPLH RL = 350 , TA = 25 C 45 Propagation Delay Time (L H)*3 75 100 ns IF = 7.5 mA, CL = 15 pF tr tf tPHL-tPLH 20 10 10 Rise Time Fall Time Pulse Width Distortion (PWD) *3 Propagation Delay Skew Common Mode Transient Immunity at High Level Output*4 Common Mode Transient Immunity at Low Level Output*4 ns ns 50 ns tPSK CMH VCC = 5 V, TA = 25 C, IF = 0 mA, VO (MIN.) = 2 V, VCM = 1.5 kV, RL = 350 15 60 ns kV/ s CML VCC = 5 V, TA = 25 C, IF = 7.5 mA, VO (MAX.) = 0.8 V, VCM = 1.5 kV, RL = 350 15 kV/ s Data Sheet PN10678EJ04V0DS 7 PS9587,PS9587L1,PS9587L2,PS9587L3 *1 Typical values at TA = 25 C *2 Because VOL of 2 V or more may be output when LED current is input and when output power supply is on and off, confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time *4 Test circuit for common mode transient immunity USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of more than 0.1 *1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Pins 1, 4 (which is an NC pin) can either be connected directly to the GND pin on the LED side or left open. Also, Pin 7 (which is an NC pin) can either be connected directly to the GND pin on the detector side or left open. Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this may degrade the internal noise environment of the device. *1 NC: Non-Connection (No Connection) 4. Avoid storage at a high temperature and high humidity. *1 8 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 TYPICAL CHARACTERISTICS (TA = 25 C, unless otherwise specified) Remark The graphs indicate nominal characteristics. Data Sheet PN10678EJ04V0DS 9 PS9587,PS9587L1,PS9587L2,PS9587L3 Remark The graphs indicate nominal characteristics. 10 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 TAPING SPECIFICATIONS (UNIT: mm) Data Sheet PN10678EJ04V0DS 11 PS9587,PS9587L1,PS9587L2,PS9587L3 12 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) Data Sheet PN10678EJ04V0DS 13 PS9587,PS9587L1,PS9587L2,PS9587L3 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220 C * Time to preheat temperature from 120 to 180 C * Number of reflows * Flux 260 C or below (package surface temperature) 10 seconds or less 60 seconds or less 120 30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260 C or below (molten solder temperature) 10 seconds or less 120 C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron * Peak Temperature (lead part temperature) * Time (each pins) * Flux 350 C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100 C 14 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler's input and output or between VCCGND at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. Data Sheet PN10678EJ04V0DS 15 PS9587,PS9587L1,PS9587L2,PS9587L3 SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Climatic test class (IEC 60068-1/DIN EN 60068-1) Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.5 UIORM, Pd 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 UIORM, Pd 5 pC Highest permissible overvoltage Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11)) Material group (DIN EN 60664-1 VDE0110 Part 1) Storage temperature range Operating temperature range Isolation resistance, minimum value VIO = 500 V dc at TA = 25C VIO = 500 V dc at TA MAX. at least 100C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = Tsi Tstg TA CTI Symbol Speck 40/85/21 Unit UIORM Upr 1 130 1 695 Vpeak Vpeak Upr 2 119 Vpeak UTR 8 000 2 175 III a -55 to +125 -40 to +85 1012 1011 Vpeak C C Ris MIN. Ris MIN. Tsi Isi Psi Ris MIN. 175 400 700 109 C mA mW 16 Data Sheet PN10678EJ04V0DS PS9587,PS9587L1,PS9587L2,PS9587L3 Data Sheet PN10678EJ04V0DS 17 PS9587,PS9587L1,PS9587L2,PS9587L3 This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. Caution GaAs Products |
Price & Availability of PS9587L1-AX
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |