Part Number Hot Search : 
TPCA80 100BF 104M00 XXXXSX BU2508D HY57V16 KBU608 AM1523CE
Product Description
Full Text Search
 

To Download SI3210 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 S i 3 2 1 0 / S i 3 2 11 / S i 3 2 1 2
P R O S LI CTM PR O G R A M M A B L E CMO S SL IC /COD E C W I T H RI N G I N G / BAT T E R Y VOLTA G E GEN E R A T I O N
Features
Performs all BORSCHT Functions Ideal for Short Loop Applications (5 REN at 2 kft, 3 REN at 4 kft) Low Voltage CMOS Package: 38-Pin TSSOP Compliant with Relevant LSSGR and CCITT Specifications Battery Voltage Generated Dynamically with On-Chip DC-DC Converter Controller (SI3210 only) 5 REN Ringing Generator Programmable Frequency, Amplitude, Waveshape, and Cadence Programmable AC Impedance A-Law/-Law, Linear PCM Companding On-Hook Transmission Programmable Constant Current Feed (20-41 mA) Programmable Loop Closure and Ring Trip Thresholds with Debouncing Loop or Ground Start Operation and Polarity Battery Reversal Continuous Line Voltage and Current Monitoring DTMF Decoder Dual Tone Generator SPI and PCM Bus Digital Interfaces with Programmable Interrupt for Control and Data 3.3 V or 5 V Operation Multiple Loopback Modes for Testing Pulse Metering FSK Caller ID Generation
Ordering Information See page 118.
Pin Assignments
SI3210/11/12
CS INT PCLK DRX
P
ro S
Applications
Terminal Adaptors Cable Telephony PBX/Key Systems Wireless Local Loop Voice Over IP Integrated Access Devices
DTX FSYNC RESET SDCH/DIO1 SDCL/DIO2 VDDA1 IREF CAPP QGND CAPM STIPDC SRINGDC STIPE SVBAT SRINGE
Description
The ProSLICTM is a low-voltage CMOS device that integrates SLIC, codec, and battery generation functionality into a complete analog telephone interface. The device is ideal for short loop applications such as terminal adaptors, cable telephony, and wireless local loop. The ProSLIC is powered with a single 3.3 V or 5 V supply. The SI3210 generates battery voltages dynamically using a software programmable dc-dc converter from a 3.3 V to 35 V supply; negative high-voltage supplies are not needed. All high voltage functions are performed locally with a few low cost discrete components. The device is available in a 38-pin TSSOP and interfaces directly to standard SPI and PCM bus digital interfaces.
Functional Block Diagram
INT RESET
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
LI C
38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20
SCLK SDI SDO SDITHRU
DCDRV/DCSW
DCFF/DOUT TEST GNDD VDDD ITIPN ITIPP VDDA2 IRINGP IRINGN IGMP GNDA IGMN SRINGAC STIPAC
SI3210/11/12
L ine Status
CS SCL K SDO SDI DTX Co ntrol Interface Co mpression DTMF Deco de G ain/ Atte nuation/ Filter Tone G ene rator G ain/ Atte nua tion / Filter A/D
Patents pending
TIP
D RX
PCM Interface Expan sio n
Progra m Hybrid
L ine Fe ed Co ntrol
Low C ost Extern al Discretes
D/A
ZS RING
FSYNC
PCL K
PLL
DC-D C Co nverter Co ntrolle r (SI3210 o nly)
Preliminary Rev. 1.11 9/01
Copyright (c) 2001 by Silicon Laboratories
SI3210-DS111
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Si 3210/ Si3 211/S i32 12
2
Preliminary Rev. 1.11
SI3210/Si3211/Si3212 TA B L E O F CONT E N TS
Section Page
4 21 21 27 30 33 37 38 39 42 42 42 43 46 47 50 108 108 110 111 112 113 115 118 119 122
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linefeed Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Voltage Generation and Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tone Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ringing Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse Metering Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DTMF Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two-Wire Impedance Matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Companding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indirect Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DTMF Decoding (SI3210 and Si3211 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital Programmable Gain/Attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLIC Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FSK Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Descriptions: SI3210/11/12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline: 38-Pin TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Rev. 1.11
3
Si 3210/ Si3 211/S i32 12
Electrical Specifications
Table 1. Absolute Maximum Ratings and Thermal Information*
Parameter DC Supply Voltage Input Current, Digital Input Pins Digital Input Voltage ESD, SI3210/11/12 (Human Body Model) Operating Temperature Range Storage Temperature Range TSSOP-38 Thermal Resistance, Typical TA TSTG JA Symbol
VDDD, VDDA1, V DDA2
Value -0.5 to 6.0 10 -0.3 to (VDDD + 0.3) 2000 -40 to 100 -40 to 150 50
Unit V mA V V C C C/W
IIN VIND
*Note: Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Table 2. Recommended Operating Conditions
Parameter Ambient Temperature Ambient Temperature SI3210/11/12 Supply Voltage Symbol TA TA VDDD,VDDA1 ,VDDA2 Test Condition K-grade B-grade Min* 0 -40 3.13 Typ 25 25 3.3/5.0 Max* 70 85 5.25 Unit
oC o
C
V
*Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at nominal supply voltages and an operating temperature of 25 oC unless otherwise stated. Product specifications are only guaranteed when the typical application circuit (including component tolerances) is used.
4
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 3. AC Characteristics
(VDDA, VDDD = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter
Test Condition TX/RX Performance
Min
Typ
Max
Unit
Overload Level Single Frequency Distortion
1
THD = 1.5% 2-wire - PCM or PCM - 2-wire: 200 Hz-3.4 kHz 200 Hz to 3.4 kHz D/A or A/D 8-bit Active off-hook, and OHT, any ZAC 0 dBm0, Active off-hook, and OHT, any Zac
2.5 --
-- --
-- -45
VPK dB
Signal-to-(Noise + Distortion) Ratio2
Figure 1
--
--
Audio Tone Generator Signal-to-Distortion Ratio2 Intermodulation Distortion Gain Accuracy2
45 --
-- -- 0 0 -- --
-- -41 0.5 0.5 -- --
dB dB dB dB
2-wire to PCM, 1014 Hz PCM to 2-wire, 1014 Hz
-0.5 -0.5 Figure 3,4 Figure 5,6
Gain Accuracy Over Frequency Group Delay Over Frequency Gain Tracking3 1014 Hz sine wave, reference level -10 dBm signal level: 3 dB to -37 dB -37 dB to -50 dB -50 dB to -60 dB Round-Trip Group Delay Gain Step Accuracy Gain Variation with Temperature Gain Variation with Supply 2-Wire Return Loss Transhybrid Balance Idle Channel Noise4 at 1000 Hz -6 dB to 6 dB All gain settings VDDA = VDDA = 3.3/5 V 5% 200 Hz to 3.4 kHz 300 Hz to 3.4 kHz Noise Performance C-Message Weighted Psophometric Weighted 3 kHz flat PSRR from VDDA PSRR from VDDD PSRR from VBAT RX and TX, DC to 3.4 kHz RX and TX, DC to 3.4 kHz RX and TX, DC to 3.4 kHz
-0.25 -0.5 -1.0 -- -0.017 -0.25 -0.1 30 30
-- -- -- 1100 -- -- -- 35 --
0.25 0.5 1.0 -- 0.017 0.25 0.1 -- --
dB dB dB s dB dB dB dB dB
-- -- -- 40 40 40
-- -- -- -- -- --
15 -75 18 -- -- --
dBrnC dBmP dBrn dB dB dB
Preliminary Rev. 1.11
5
Si 3210/ Si3 211/S i32 12
Table 3. AC Characteristics (Continued)
(VDDA, VDDD = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter
Test Condition Longitudinal Performance 200 Hz to 3.4 kHz, Q1,Q2 150, 1% mismatch Q1,Q2 = 60 to 2405 Q1,Q2 = 300 to 8005
Min
Typ
Max
Unit
Longitudinal to Metallic or PCM Balance
56 43 53 40
60 60 60 --
-- -- -- --
dB dB dB dB
Metallic to Longitudinal Balance Longitudinal Impedance
200 Hz to 3.4 kHz 200 Hz to 3.4 kHz at TIP or RING Register selectable
ETBO/ETBA
00 01 10 Longitudinal Current per Pin Active off-hook 200 Hz to 3.4 kHz Register selectable
ETBO/ETBA
-- -- --
33 17 17
-- -- --

00 01 10
-- -- --
4 8 8
-- -- --
mA mA mA
Notes: 1. The input signal level should be 0 dBm0 for frequencies greater than 100 Hz. For 100 Hz and below, the level should be -10 dBm0. The output signal magnitude at any other frequency will be smaller than the maximum value specified. 2. Analog signal measured as VTIP - VRING. Assumes ideal line impedance matching. 3. The quantization errors inherent in the /A-law companding process can generate slightly worse gain tracking performance in the signal range of 3 dB to -37 dB for signal frequencies that are integer divisors of the 8 kHz PCM sampling rate. 4. The level of any unwanted tones within the bandwidth of 0 to 4 kHz does not exceed -55 dBm. 5. Assumes normal distribution of betas.
6
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Figure 1. Transmit and Receive Path SNDR
9 8 7 6
Fundamental Output Power 5 (dBm0) Acceptable Region
4 3
2.6
2 1 0 1 2 3 4 5 6 7 8 9
Fundamental Input Power (dBm0)
Figure 2. Overload Compression Performance
Preliminary Rev. 1.11
7
Si 3210/ Si3 211/S i32 12
Typical Response
Typical Response
Figure 3. Transmit Path Frequency Response
8
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Figure 4. Receive Path Frequency Response
Preliminary Rev. 1.11
9
Si 3210/ Si3 211/S i32 12
Figure 5. Transmit Group Delay Distortion
Figure 6. Receive Group Delay Distortion
10
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 4. Linefeed Characteristics
(VDDA, VDDD = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter Loop Resistance Range DC Loop Current Accuracy DC Open Circuit Voltage Accuracy DC Differential Output Resistance DC Open Circuit Voltage-- Ground Start DC Output Resistance-- Ground Start DC Output Resistance-- Ground Start Loop Closure/Ring Ground Detect Threshold Accuracy Ring Trip Threshold Accuracy Ring Trip Response Time Ring Amplitude Ring DC Offset Trapezoidal Ring Crest Factor Accuracy Sinusoidal Ring Crest Factor Ringing Frequency Accuracy Ringing Cadence Accuracy Calibration Time Power Alarm Threshold Accuracy
Symbol RLOOP
Test Condition See note.* ILIM = 29 mA, ETBA = 4 mA Active Mode; VOC = 48 V, VTIP - VRING
Min 0 -10 -4 -- -4 -- 150 -20 -20 -- 44 0 -.05 1.35
Typ -- -- -- 160 -- 160 -- -- -- -- -- -- -- -- -- -- -- --
Max 160 10 4 -- 4 -- -- 20 20 -- -- -- .05 1.45 1 50 600 25
Unit % V V k % %
RDO VOCTO RROTO RTOTO
ILOOP < ILIM IRINGVTR ROS
5 REN load; sine wave; RLOOP = 160 , VBAT = -75 V Programmable in Indirect Register 19 Crest factor = 1.3
VRMS V
RCF f = 20 Hz Accuracy of ON/OFF Times CAL to CAL Bit At Power Threshold = 300 mW
-1 -50 -- -25
% msec msec %
*Note: DC resistance round trip; 160 corresponds to 2 kft 26 gauge AWG.
Preliminary Rev. 1.11
11
Si 3210/ Si3 211/S i32 12
Table 5. Monitor ADC Characteristics
(VDDA, VDDD = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter Differential Nonlinearity (6-bit resolution) Integral Nonlinearity (6-bit resolution) Gain Error (voltage) Gain Error (current)
Symbol DNLE INLE
Test Condition
Min -1/2 -1 -- --
Typ -- -- -- --
Max 1/2 1 10 20
Unit LSB LSB % %
Table 6. Si321x DC Characteristics, VDDA = VDDD = 5.0 V
(VDDA,VDDD = 4.75 V to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage
Symbol VIH VIL VOH
Test Condition
Min 0.7 VDDD --
Typ -- -- -- -- --
Max -- 0.3 VDDD -- -- 0.4
Unit V V V V V
DIO1,DIO2,SDITHRU:IO = -4 mA VDDD - 0.6 SDO, DTX:IO = -8 mA DOUT: IO = -40 mA
VDDD - 0.8 --
Low Level Output Voltage
VOL
DIO1,DIO2,DOUT,SDITHRU: IO = 4 mA SDO,INT,DTX:IO = 8 mA
Input Leakage Current
IL
-10
--
10
A
Table 7. Si321x DC Characteristics, VDDA = VDDD = 3.3 V
(VDDA,VDDD = 3.13 V to 3.47 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage
Symbol VIH VIL VOH
Test Condition
Min 0.7 VDDD --
Typ -- -- -- -- --
Max -- 0.3 VDDD -- -- 0.4
Unit V V V V V
DIO1,DIO2,SDITHRU:IO = -2 mA VDDD - 0.6 SDO, DTX:IO = -4 mA DOUT: IO = -40 mA
VDDD - 0.8 --
Low Level Output Voltage
VOL
DIO1,DIO2,DOUT,SDITHRU: IO = 2 mA SDO,INT,DTX:IO = 4 mA
Input Leakage Current
IL
-10
--
10
A
12
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 8. Power Supply Characteristics
(VDDA,VDDD = 3.13 V to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade)
Parameter Power Supply Current, Analog and Digital
Symbol IA + ID
Test Condition Sleep (RESET = 0) Open Active on-hook ETBO = 4 mA Active OHT ETBO = 4 mA Active off-hook ETBA = 4 mA, ILIM = 20 mA Ground-start Ringing Sinewave, REN = 1, VPK = 56 V
Typ1 0.1 33 46
Typ2 0.25 42.8 57
Max 0.42 49 68
Unit mA mA mA
57 73 36 45 -- --
72 88 47 55 0 0
83 99 55 65 -- --
mA mA mA mA mA mA mA
Power Supply Current,
VBAT3
IBAT
Sleep (RESET = 0) Open (DCOF = 1) Active on-hook VOC = 48 V, ETBO = 4 mA Active OHT ETBO = 4 mA Active off-hook ETBA = 4 mA, ILIM = 20 mA Ground-start Ringing VPK_RING = 56 VPK, sinewave ringing, REN = 1
--
3
--
--
11
--
mA
-- --
30 2
-- --
mA mA mA
--
5.5
--
Notes: 1. VDDD, V DDA = 3.3 V. 2. VDDD, V DDA = 5.25 V. 3. IBAT = current from VBAT (the large negative supply). For a switched-mode power supply regulator efficiency of 71%, the user can calculate the regulator current consumption as IBAT V BAT/(0.71 V DC).
Table 9. Switching Characteristics--General Inputs
VDDA = VDDA = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade, CL = 20 pF)
Parameter Rise Time, RESET RESET Pulse Width
Symbol tr trl
Min -- 100
Typ -- --
Max 20 --
Unit ns ns
Note: All timing (except Rise and Fall time) is referenced to the 50% level of the waveform. Input test levels are V IH = VD - 0.4 V, VIL = 0.4 V. Rise and Fall times are referenced to the 20% and 80% levels of the waveform.
Preliminary Rev. 1.11
13
Si 3210/ Si3 211/S i32 12
Table 10. Switching Characteristics--SPI
VDDA = VDDA = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade, CL = 20 pF
Parameter Cycle Time SCLK Rise Time, SCLK Fall Time, SCLK Delay Time, SCLK Fall to SDO Active Delay Time, SCLK Fall to SDO Transition Delay Time, CS Rise to SDO Tri-state Setup Time, CS to SCLK Fall Hold Time, CS to SCLK Rise Setup Time, SDI to SCLK Rise Hold Time, SDI to SCLK Rise Delay Time between Chip Selects SDI to SDITHRU Propagation Delay
Symbol tc tr tf td1 td2 td3 tsu1 th1 tsu2 th2 tcs tcs
Test Conditions
Min 0.062 -- -- -- -- -- 25 20 25 20 220 --
Typ -- -- -- -- -- -- -- -- -- -- -- 4
Max -- 25 25 20 20 20 -- -- -- -- -- --
Unit sec ns ns ns ns ns ns ns ns ns ns ns
Note: All timing is referenced to the 50% level of the waveform. Input test levels are VIH = VDDD -0.4 V, VIL = 0.4 V
tr
tthru tc
tr
SCLK
tsu1
th1
CS
tcs tsu2 th2
SDI
td1 td2 td3
SDO
Figure 7. SPI Timing Diagram
14
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 11. Switching Characteristics--PCM Highway Serial Interface
VD = 3.13 to 5.25 V, TA = 0 to 70C for K-Grade, -40 to 85C for B-Grade, CL = 20 pF
Parameter PCLK Frequency
Symbol 1/tc
Test Conditions
Min 1 -- -- -- -- -- -- -- -- 40 -120 -- -- -- -- -- 25 20 25 20
Typ 1 0.256 0.512 0.768 1.024 1.536 2.048 4.096 8.192 50 -- -- -- -- -- -- -- -- -- --
Max 1 -- -- -- -- -- -- -- -- 60 120 25 25 20 20 20 -- -- -- --
Units MHz MHz MHz MHz MHz MHz MHz MHz % ns ns ns ns ns ns ns ns ns ns
PCLK Duty Cycle Tolerance PCLK Period Jitter Tolerance Rise Time, PCLK Fall Time, PCLK Delay Time, PCLK Rise to DTX Active Delay Time, PCLK Rise to DTX Transition Delay Time, PCLK Rise to DTX Tri-state2 Setup Time, FSYNC to PCLK Fall Hold Time, FSYNC to PCLK Fall Setup Time, DRX to PCLK Fall Hold Time, DRX to PCLK Fall
tdty tjitter tr tf td1 td2 td3 tsu1 th1 tsu2 th2
Notes: 1. All timing is referenced to the 50% level of the waveform. Input test levels are VIH - V I/O -0.4V, VIL = 0.4V 2. Spec applies to PCLK fall to DTX tri-state when that mode is selected (TRI = 0).
tc PCLK t su1 FSYNC t su2 DRX t d1 DTX td2 t h2 th1
tr
tf
t d3
Figure 8. PCM Highway Interface Timing Diagram
Preliminary Rev. 1.11
15
Si 3210/ Si3 211/S i32 12
VCC 32 31 23 10 27 GND
GNDD
GNDA
R1 200k GND 15 20 C3 220nF R8 470
VDDA1
VDDA2
VDDD
TEST
30
SCLK STIPDC STIPAC SDI SDO CS FSYNC ITIPP PCLK
38 37 36 1
SPI Bus
6 3 4 5
Q1 5401 R10 10
Q4 5401
28 29 17 R2 200k 26 Q2 5401 R11 10 Q5 5551 C7 220nF R7 80.6 C4 220nF R9 470 R12 5.1k R5 200k Q3 5401 R4 200k 25 19
SI3210/SI3210M
TIP
Protection Circuit C5 22nF C6 22nF
Q6 5551 C8 220nF R6 80.6 R13 5.1k
ITIPN STIPE
DRX DTX
PCM Bus
VCC
R322 10k
IRINGP IRINGN SRINGE
INT RESET IGMP IGMN
2 7 Note 2 R262 40.2k R15 243
RING
24 22
18
SVBAT
IREF CAPP CAPM
11 12 14 C2 10uF C1 10uF R14 40.2k
21 16
Notes: 1. Values and configurations for these components can be derived from Table 19 or from App Note 45. 2. Only one component per system needed. 3. All circuit grounds should have a singlepoint connection to the ground plane.
R21 15 C26 0.1uF Q9 2N2222 VCC R291 R281 R3 200k
SRINGAC SRINGDC DCDRV SDCH DCFF SDCL
QGND
13
GND
9
8
34
33
DCDRV
SDCH
DCFF
SDCL
VDC
VDDA1
VDDA2
VDDD
Note 1
VBAT
DC-DC Converter Circuit
VDC
C15 0.1uF
C16 0.1uF
C17 0.1uF
C30 10uF
Figure 9. SI3210/SI3210M Typical Application Circuit Using Integrated DC-DC Converter Table 12. SI3210/SI3210M External Component Values
Component
C1,C2 C3,C4 C5,C6 C7,C8 C15,C16,C17 C26 C30 Q1,Q2,Q3,Q4 Q5,Q6 Q9
Value
10 F, 6 V Ceramic/Tantalum or 16 V Low Leakage Electrolytic, 20% 220 nF, 100 V, X7R, 20% 22 nF, 100 V, X7R, 20% 220 nF, 50 V, X7R, 20% 0.1 F, 6 V, Y5V, 20% 0.1 F, 100 V, X7R, 20% 10 F, 16 V, Electrolytic, 20% 100 V, PNP, BJT 100 V, NPN, BJT NPN General Purpose BJT
Supplier/Part Number
Murata, Panasonic, Nichicon URL16100MD, Panasonic Z Series Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Panasonic Central Semi CMPT5401; ON Semi MMBT5401LT1, 2N5401; Zetex FMMT5401 Central Semi CZT5551, ON Semi 2N5551 ON Semi MMBT2222ALT1, MPS2222A; Central Semi CMPT2222A; Zetex FMMT2222
R1,R2,R3,R4,R5 200 k, 1/10 W, 1% R6,R7 80.6 , 1/4 W, 1% R8,R9 470 , 1/10 W, 1% R10,R11 10 , 1/10 W, 5% R12,R13 5.1 k, 1/10 W, 5% R14,R26* 40.2 k, 1/10 W, 1% R15 243 , 1/10 W, 1% R21 15 , 1/4 W, 1% R28,R29 1/10 W, 1% (See AN45 or Table 17 for value selection) R32* 10 k, 1/10 W, 5% *Note: Only one component per system needed.
16
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
VDC
F1
SDCH R19 1
Note 1
SDCL R20 1
R181
C252 10uF
C142 0.1uF
SI3210
C10 22nF
R16 200 Q8 FZT953
DCFF
Q8 2N2222
D1 ES1D C9 10uF
VBAT
R17 L1 DCDRV
Note 1
GND
Notes: 1. Values and configurations for these components can be derived from Table 21 or from App Note 45. 2. Voltage rating for C14 and C25 must be greater than VDC.
Figure 10. SI3210 BJT/Inductor DC-DC Converter Circuit Table 13. SI3210 BJT/Inductor DC-DC Converter Component Values
Component (s)
C9 C10 C14* C25* R16 R17 R18 R19,R20 F1 D1 L1
Value
10 F, 100 V, Electrolytic, 20% 22 nF, 50 V, X7R, 20% 0.1 F, X7R, 20% 10 F, Electrolytic, 20% 200 , 1/10 W, 5% 1/10 W, 5% (See AN45 or Table 19 for value selection) 1/4 W, 5% (See AN45 or Table 19 for value selection) 1/10 W, 1% (See AN45 or Table 19 for value selection) Fuse Ultra Fast Recovery 200 V, 1A Rectifier 1A, Shielded Inductor (See AN45 or Table 19 for value selection)
Supplier
Panasonic Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Panasonic
Q7 Q8
120 V, High Current Switching PNP 60 V, General Purpose Switching NPN
Belfuse SSQ Series General Semi ES1D; Central Semi CMR1U-02 API Delevan SPD127 series, Sumida CDRH127 series, Datatronics DR340-1 series, Coilcraft DS5022, TDK SLF12565 Zetex FZT953, FZT955, ZTX953, ZTX955 ON Semi MMBT2222ALT1, MPS2222A; Central Semi CMPT2222A; Zetex FMMT2222
*Note: Voltage rating of this device must be greater than VDC.
Preliminary Rev. 1.11
17
Si 3210/ Si3 211/S i32 12
VDC
F1
SDCH R191
Note 1
SDCL R201
R18 1
C252 10uF
C142 0.1uF
SI3210M
1 C27 470pF DCFF M1 IRLL014N R22 22 2 3 4 T11 6 10 D1 ES1D C9 10uF VBAT
Note 1
R17 200k DCDRV NC
GND
Notes: 1. Values and configurations for these components can be derived from Table 20 or from App Note 45. 2. Voltage rating for C14 and C25 must be greater than VDC.
Figure 11. SI3210M MOSFET/Transformer DC-DC Converter Circuit Table 14. SI3210M MOSFET/Transformer DC-DC Converter Component Values
Component (s) C9 C14* C25* C27 R17 R18 R19,R20 Value Supplier 10 F, 100 V, Electrolytic, 20% Panasonic 0.1 F, X7R, 20% Murata, Johanson, Novacap, Venkel 10 F, Electrolytic, 20% Panasonic 470 pF, 100 V, X7R, 20% Murata, Johanson, Novacap, Venkel 200 k, 1/10 W, 5% 1/4 W, 5% (See AN45 or Table 18 for value selection) 1/10 W, 1% (See AN45 or Table 18 for value selection) 22 , 1/10 W, 5% Fuse Belfuse SSQ Series Ultra Fast Recovery 200 V, 1A Rectifier General Semi ES1D; Central Semi CMR1U-02 Power Transformer Coiltronic CTX01-15275; Datatronics SM76315; Midcom 31353R-02 100 V, Logic Level Input MOSFET Intl Rect. IRLL014N; Intersil HUF76609D3S; ST Micro STD5NE10L, STN2NE10L
R22 F1 D1 T1
M1
*Note: Voltage rating of this device must be greater than V DC.
18
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
VCC 32 31 23 10 27 30
TEST
VDDA1
VDDA2
GNDD
R1 200k GND 15 20 C3 220nF R8 470
GNDA
VDDD
STIPDC STIPAC
SCLK SDI SDO CS
38 37 36 1
SPI Bus
Q1 5401 R10 10
Q4 5401
28 29 17 R2 200k 26 Q2 5401 R11 10 Q5 5551 C7 220nF R7 80.6 C4 220nF R9 470 21 R12 5.1k R5 200k Q3 5401 R4 200k 25 19
ITIPP ITIPN STIPE
FSYNC PCLK DRX DTX
6 3 4 5
Protection Circuit
C5 22nF C6 22nF
C8 220nF R6 80.6
R13 5.1k
Si3211/Si3212
TIP
Q6 5551
PCM Bus
VCC
IRINGP IRINGN SRINGE
R321 10k
RING
INT RESET IGMP IGMN
2 7 Note 1 R261 40.2k R15 243
24 22
18
SVBAT IREF CAPP SRINGAC SRINGDC DCSW QGND DOUT
13 11 12 14 C2 10uF C1 10uF R14 40.2k
Notes: 1. Only one component per system needed. 2. All circuit grounds should have a single-point connection to the ground plane.
Q8 5551 D1 4003 R16 200k VBATL VBATH Q7 5401 R18 1.8k C9 0.1uF R3 200k 16
CAPM
DIO2
GND
DIO1
34
NC NC
33
VDDA1 C15 0.1uF C16 0.1uF
VDDA2 C17 0.1uF
VDDD
9
8
NC
Figure 12. Si3211/12 Typical Application Circuit Using Extended Battery Table 15. Si3211/12 External Component Values
Component
C1,C2 C3,C4 C5,C6 C7,C8 C9 C15,C16,C17 R1,R2,R3,R4,R5,R16 R6,R7 R8,R9 R10,R11 R12,R13 R14,R26* R15 R18 R32* D1 Q1,Q2,Q3,Q4,Q7 Q5,Q6 Q8
Value
10 F, 6 V Ceramic/Tantalum or 16 V Low Leakage Electrolytic, 20% 220 nF, 100 V, X7R, 20% 22 nF, 100 V, X7R, 20% 220 nF, 50 V, X7R, 20% 0.1 F, 100 V, Electrolytic, 20% 0.1 F, 6 V, Y5V, 20% 200 k, 1/10 W, 1% 80.6 , 1/4 W, 1% 470 , 1/10 W, 1% 10 , 1/10 W, 5% 5.1 k, 1/10 W, 5% 40.2 k, 1/10 W, 1% 243 , 1/10 W, 1% 1.8 k, 1/10 W, 5% 10 k, 1/10 W, 5% 200 V 1A Rectifier 100 V, PNP, BJT 100 V, NPN, BJT 100 V, NPN, BJT
Supplier/Part Number
Murata, Panasonic, Nichicon URL16100MD, Panasonic Z Series Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Murata, Johanson, Novacap, Venkel Panasonic Murata, Johanson, Novacap, Venkel
ON Semi MRA4003, 1N4003 Central Semi CMPT5401; ON Semi MMBT5401LT1, 2N5401; Zetex FMMT5401 Central Semi CZT5551, ON Semi 2N5551 Central Semi CMPT5551, ON Semi 2N5551
*Note: Only one component per system needed.
Preliminary Rev. 1.11
19
Si 3210/ Si3 211/S i32 12
QRDN Q3 5401 Q4 5401 QTDN
R23 RRBN0 3.0k QRP Q5 5551 C7 CRBN 100 nF R6 RTE 80.6 Q6 5551 QTN
R24 RTBN0 3.0k
C8 CTBN 100 nF
R7 RRE 80.6
R12 RRBN 5.1k
R13 RTBN 5.1k
Figure 13. Si321x Optional Equivalent Q5, Q6 Bias Circuit Table 16. Si321x Optional Bias Component Values
Component C7,C8 R23,R24 Value 100 nF, 100 V, X7R, 20% 3.0 k, 1/10 W, 5% Supplier/Part Number Murata, Johanson, Venkel
The subcircuit above can be substituted into any of the ProSLIC solutions as an optional bias circuit for Q5, Q6. For this optional subcircuit, C7 and C8 are different in voltage and capacitance to the standard circuit. R23 and R24 are additional components.
Table 17. Component Value Selection for SI3210/SI3210M
Component R28 Value 1/10 W, 1% resistor For VDD = 3.3 V: 26.1 k For VDD = 5.0 V: 37.4 k 1/10 W, 1% resistor For VCLAMP = 80 V: 541 k For VCLAMP = 85 V: 574 k For VCLAMP = 100 V: 676 k Comments R28 = (VDD + VBE)/148 A where VBE is the nominal VBE for Q9 R29 = VCLAMP/148 A where VCLAMP is the clamping voltage for VBAT
R29
Table 18. Component Value Selection Examples for SI3210M MOSFET/Transformer DC-DC Converter
VDC 3.3 V 5.0 V 12 V 24 V
Note:
Ringing Load/Loop Resistance 3 REN/117 5 REN/117 5 REN/117 5 REN/117
Transformer Ratio 1-2 1-2 1-3 1-4
R18 0.56 0.10 0.68 2.20
R19, R20 7.15 k 16.5 k 56.2 k 121 k
There are other system and software conditions that influence component value selection, so please refer to AN45 "Design Guide for the SI3210 DC-DC Converter for detailed guidance.
Table 19. Component Value Selection Examples for SI3210 BJT/Inductor DC-DC Converter
VDC 5V 12 V 24 V
Note:
Ringing Load/Loop Length 3 REN/117 5 REN/117 5 REN/117
L1 33 H 150 H 560 H
R17 100 162 274
R18 0.12 0.56 2.2
R19, R20 16.5 k 56.2k 121 k
There are other system and software conditions that influence component value selection, so please refer to AN45 "Design Guide for the SI3210 DC-DC Converter for detailed guidance.
20
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Functional Description
The ProSLICTM is a single low-voltage CMOS device that provides all the SLIC, codec, DTMF detection, and signal generation functions needed for a complete analog telephone interface. The ProSLIC performs all battery, overvoltage, ringing, supervision, codec, hybrid, and test (BORSCHT) functions. Unlike most monolithic SLICs, the SI3210 does not require externally supplied high-voltage battery supplies. Instead, it generates all necessary battery voltages from a positive dc supply using its own dc-dc converter controller. Two fully programmable tone generators can produce DTMF tones, phase continuous FSK (caller ID) signaling, and call progress tones. DTMF decoding and pulse metering signal generation are also integrated. The ProSLIC is ideal for short loop applications, such as terminal adapters, cable telephony, PBX/key systems, wireless local loop (WLL), and voice over IP solutions. The device meets all relevant LSSGR and CCITT standards. The linefeed provides programmable on-hook voltage, programmable off-hook loop current, reverse battery operation, loop or ground start operation, and on-hook transmission ringing voltage. Loop current and voltage are continuously monitored using an integrated A/D converter. Balanced 5 REN ringing with or without a programmable dc offset is integrated. The available offset, frequency, waveshape, and cadence options are designed to ring the widest variety of terminal devices and to reduce external controller requirements. A complete audio transmit and receive path is integrated, including DTMF decoding, ac impedance, and hybrid gain. These features are software programmable, allowing for a single hardware design to meet international requirements. Digital voice data transfer occurs over a standard PCM bus. Control data is transferred using a standard SPI. The device is available in a 38-pin TSSOP. 1.5 V steps. The loop current limit (ILIM) defines the constant current zone and is programmable from 20 mA to 41 mA in 3 mA steps. The ProSLIC has an inherent dc output resistance (RO) of 160 .
V (TIP-RING ) (V) Constant Voltage Zone
VOC
R O =160 ILIM
Constant Current Zone I LO O P (m A)
Figure 14. Simplified DC Current/Voltage Linefeed Characteristic
The TIP-to-RING voltage (VOC) is offset from ground by a programmable voltage (VCM) to provide voltage headroom to the positive-most terminal (TIP in forward polarity states and RING in reverse polarity states) for carrying audio signals. Table 20 summarizes the parameters to be initialized before entering an active state.
Table 20. Programmable Ranges of DC Linefeed Characteristics
Parameter Programmable Range Default Value Register Bits Location*
ILIM VOC VCM
20 to 41 mA
20 mA
ILIM[2:0]
Direct Register 71 Direct Register 72 Direct Register 73
0 to 94.5 V
48 V
VOC[5:0]
Linefeed Interface
The ProSLIC's linefeed interface offers a rich set of features and programmable flexibility to meet the broadest applications requirements. The dc linefeed characteristics are software programmable; key current, voltage, and power measurements are acquired in realtime and provided in software registers.
DC Feed Characteristics
0 to 94.5 V
3V
VCM[5:0]
*Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly.
The ProSLIC has programmable constant voltage and constant current zones as depicted in Figure 14. Open circuit TIP-to-RING voltage (VOC) defines the constant voltage zone and is programmable from 0 V to 94.5 V in
Preliminary Rev. 1.11 21
Si 3210/ Si3 211/S i32 12
Linefeed Architecture Loop Voltage and Current Monitoring
The ProSLIC is a low-voltage CMOS device that uses low-cost external components to control the high voltages required for subscriber line interfaces. Figure 15 is a simplified illustration of the linefeed control loop circuit for TIP or RING and the external components used. The ProSLIC uses both voltage and current sensing to control TIP and RING. DC and AC line voltages on TIP and RING are measured through sense resistors RDC and RAC, respectively. The ProSLIC uses linefeed transistors QP and QN to drive TIP and RING. QDN isolates the high-voltage base of QN from the ProSLIC. The ProSLIC measures voltage at various nodes in order to monitor the linefeed current. RDC, RSE, and RBAT provide access to these measuring points. The sense circuitry is calibrated on-chip to guarantee measurement accuracy with standard external component tolerances. See "Linefeed Calibration" on page 26 for details.
Linefeed Operation States
The ProSLIC continuously monitors the TIP and RING voltages and external BJT currents. These values are available in registers 78-89. Table 22 on page 24 lists the values that are measured and their associated registers. An internal A/D converter samples the measured voltages and currents from the analog sense circuitry and translates them into the digital domain. The A/D updates the samples at an 800 Hz rate. Two derived values are also reported--loop voltage and loop current. The loop voltage, VTIP - VRING, is reported as a 1-bit sign, 6-bit magnitude format. For ground start operation the reported value is the RING voltage. The loop current, (IQ1 - IQ2 + IQ5 -IQ6)/2, is reported in a 1bit sign, 6-bit magnitude format. In RING open and TIP open states the loop current is reported as (IQ1 - IQ2) + (IQ5 -IQ6).
The ProSLIC linefeed has eight states of operation as shown in Table 21. The state of operation is controlled using the Linefeed Control register (direct Register 64). The open state turns off all currents into the external bipolar transistors and can be used in the presence of fault conditions on the line and to generate Open Switch Intervals (OSIs). TIP and RING are effectively tri-stated with a dc output impedance of about 150 k. The ProSLIC can also automatically enter the open state if it detects excessive power being consumed in the external bipolar transistors. See "Power Monitoring and Line Fault Detection" on page 24 for more details. In the forward active and reverse active states, linefeed circuitry is on and the audio signal paths are powered down. In the forward and reverse on-hook transmission states audio signal paths are powered up to provide data transmission during an on-hook loop condition. The TIP Open state turns off all control currents to the external bipolar devices connected to TIP and provides an active linefeed on RING for ground start operation. The RING Open state provides similar operation with the RING drivers off and TIP active. The ringing state drives waveforms onto the line. programmable ringing
22
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Aud io Codec A/D
M onitor A/D A/D
DSP
D/A D/A SLIC DAC
O n-C hip
AC Control
AC Sense
Battery Sense
DC Control
DC Sense
Em itter Sense
External Com ponents
R AC C AC
AC Control Loop
QP R BP
Q DN
DC Control Loop
R DC
R SE
R BAT
T IP o r RING
QN
RE V B AT
Figure 15. Simplified ProSLIC Linefeed Architecture for TIP and RING Leads (One Shown) Table 21. ProSLIC Linefeed Operations
LF[2:0]* Linefeed State Description
000 001 010 011 100 101 110 111
Open Forward Active Forward On-Hook Transmission TIP Open Ringing Reverse Active Reverse On-Hook Transmission Ring Open
TIP and RING tri-stated. VTIP > VRING. VTIP > VRING; audio signal paths powered on. TIP tri-stated, RING active; used for ground start. Ringing waveform applied to TIP and RING. VRING > VTIP. VRING > VTIP; audio signal paths powered on. RING tri-stated, TIP active.
Note: The Linefeed register (LF) is located in direct Register 64.
Preliminary Rev. 1.11
23
Si 3210/ Si3 211/S i32 12
Table 22. Measured Realtime Linefeed Interface Characteristics
Parameter Measurement Range Resolution Register Bits Location*
Loop Voltage Sense (VTIP - VRING) Loop Current Sense TIP Voltage Sense RING Voltage Sense Battery Voltage Sense 1 (VBAT) Battery Voltage Sense 2 (VBAT) Transistor 1 Current Sense Transistor 2 Current Sense Transistor 3 Current Sense Transistor 4 Current Sense Transistor 5 Current Sense Transistor 6 Current Sense
-94.5 to +94.5 V -80 to +80 mA 0 to -95.88 V 0 to -95.88 V 0 to -95.88 V 0 to -95.88 V 0 to 81.35 mA 0 to 81.35 mA 0 to 9.59 mA 0 to 9.59 mA 0 to 80.58 mA 0 to 80.58 mA
1.5 V 1.27 mA 0.376 V 0.376 V 0.376 V 0.376 V 0.319 mA 0.319 mA 37.6 A 37.6 A 0.316 mA 0.316 mA
LVSP, LVS[6:0] LCSP, LCS[5:0] VTIP[7:0] VRING[7:0] VBATS1[7:0] VBATS2[7:0] IQ1[7:0] IQ2[7:0] IQ3[7:0] IQ4[7:0] IQ5[7:0] IQ6[7:0]
Direct Register 78 Direct Register 79 Direct Register 80 Direct Register 81 Direct Register 82 Direct Register 83 Direct Register 84 Direct Register 85 Direct Register 86 Direct Register 87 Direct Register 88 Direct Register 89
*Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly.
Power Monitoring and Line Fault Detection
In addition to reporting voltages and currents, the ProSLIC continuously monitors the power dissipated in each external bipolar transistor. Realtime output power of any one of the six linefeed transistors can be read by setting the Power Monitor Pointer (direct Register 76) to point to the desired transistor and then reading the Line Power Output Monitor (direct Register 77). The realtime power measurements are low-pass filtered and compared to a maximum power threshold. Maximum power thresholds and filter time constants are software programmable and should be set for each transistor pair based on the characteristics of the transistors used. Table 23 describes the registers associated with this function. If the power in any external transistor exceeds the programmed threshold, a power alarm event is triggered. The ProSLIC sets the Power Alarm register bit, generates an interrupt (if enabled), and automatically enters the Open state (if AOPN = 1). This feature protects the external transistors from fault conditions and, combined with the loop voltage and current monitors, allows diagnosis of
the type of fault condition present on the line. The value of each thermal low-pass filter pole is set according to the equation:
4096 3 thermal LPF register = ---------------- 2 800
where is the thermal time constant of the transistor package, 4096 is the full range of the 12-bit register, and 800 is the sample rate in hertz. Generally = 3 seconds for SOT223 packages and = 0.16 seconds for SOT23, but check with the manufacturer for the package thermal constant of a specific device. For example, the power alarm threshold and low-pass filter values for Q5 and Q6 using a SOT223 package transistor are computed as follows:
P MAX 1.28 - 7 -7 PPT56 = ------------------------------ 2 = ----------------- 2 = 5389 = 150Dh Resolution 0.0304
Thus, indirect Register 34 should be set to 150Dh.
Note: The power monitor resolution for Q3 and Q4 is different from that of Q1, Q2, Q5, and Q6.
24
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 23. Associated Power Monitoring and Power Fault Registers
Parameter Description/ Range Resolution Register Bits Location*
Power Monitor Pointer
0 to 5 points to Q1 to Q6, respectively 0 to 7.8 W for Q1, Q2, Q5, Q6 0 to 0.9 W for Q3, Q4 0 to 7.8 W 0 to 0.9 W 0 to 7.8 W
n/a
PWRMP[2:0]
Direct Register 76
Line Power Monitor Output
30.4 mW 3.62 mW
PWROM[7:0]
Direct Register 77
Power Alarm Threshold, Q1 & Q2 Power Alarm Threshold, Q3 & Q4 Power Alarm Threshold, Q5 & Q6 Thermal LPF Pole, Q1 & Q2 Thermal LPF Pole, Q3 & Q4 Thermal LPF Pole, Q5 & Q6 Power Alarm Interrupt Pending
30.4 mW 3.62 mW 30.4 mW
PPT12[7:0] PPT34[7:0] PPT56[7:0] NQ12[7:0] NQ34[7:0] NQ56[7:0]
Indirect Register 32 Indirect Register 33 Indirect Register 34 Indirect Register 37 Indirect Register 38 Indirect Register 39 Direct Register 19
see equation above see equation above see equation above Bits 2 to 7 correspond to Q1 to Q6, respectively Bits 2 to 7 correspond to Q1 to Q6, respectively 0 = manual mode 1 = enter open state upon power alarm n/a
QnAP[n+1], where n =1 to 6 QnAE[n+1], where n = 1 to 6 AOPN
Power Alarm Interrupt Enable
n/a
Direct Register 22
Power Alarm Automatic/Manual Detect
n/a
Direct Register 67
*Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly. An "indirect" register is one that is accessed using the indirect access registers (direct registers 28 through 31).
Preliminary Rev. 1.11
25
Si 3210/ Si3 211/S i32 12
LCS LVS Input Signal Processor ISP_OUT Digital LPF + D ebounce Filter - NCLR LFS LCVE HYSTEN Loop Closure Thres hold LCDI LCIE LCR LCIP
Interrupt Logic
LCRT LCRTL
Figure 16. Loop Closure Detection
Loop Closure Detection
which set the upper and lower bounds, respectively.
Voltage-Based Loop Closure Detection
A loop closure event signals that the terminal equipment has gone off-hook during on-hook transmission or onhook active states. The ProSLIC performs loop closure detection digitally using its on-chip monitor A/D converter. The functional blocks required to implement loop closure detection are shown in Figure 16. The primary input to the system is the Loop Current Sense value provided in the LCS register (direct Register 79). The LCS value is processed in the Input Signal Processor when the ProSLIC is in the on-hook transmission or on-hook active linefeed state, as indicated by the Linefeed Shadow register, LFS[2:0] (direct Register 64). The data then feeds into a programmable digital low-pass filter, which removes unwanted ac signal components before threshold detection. The output of the low-pass filter is compared to a programmable threshold, LCRT (indirect register 28). The threshold comparator output feeds a programmable debouncing filter. The output of the debouncing filter remains in its present state unless the input remains in the opposite state for the entire period of time programmed by the loop closure debounce interval, LCDI (direct Register 69). If the debounce interval has been satisfied, the LCR bit will be set to indicate that a valid loop closure has occurred. A loop closure interrupt is generated if enabled by the LCIE bit (direct Register 22). Table 24 lists the registers that must be written or monitored to correctly detect a loop closure condition.
Silicon revisions C and higher also support an optional voltage-based loop closure detection mode, which is enabled by setting LCVE = 1 (direct Register 108, bit 2). In this mode the loop voltage is compared to the loop closure threshold register (LCRT) which represents a minimum voltage threshold instead of a maximum current threshold. If hysteresis is also enabled, then LCRT represents the upper voltage boundary and LCRTL represents the lower voltage boundary for hysteresis. Although voltage-based loop closure detection is an option, the default current-based loop closure detection is recommended.
Table 24. Register Set for Loop Closure Detection
Parameter Register Location Loop Closure LCIP Direct Reg. 19 Interrupt Pending Loop Closure LCIE Direct Reg. 22 Interrupt Enable Loop Closure Threshold LCRT[5:0] Indirect Reg. 28 Loop Closure LCRTL[5:0] Indirect Reg. 43 Threshold--Lower Loop Closure Filter NCLR[12:0] Indirect Reg. 35 Coefficient Loop Closure Detect LCR Direct Reg. 68 Status (monitor only) Loop Closure Detect LCDI[6:0] Direct Reg. 69 Loop Closure Threshold Hysteresis Debounce Interval Silicon revisions C and higher support the addition of Hysteresis Enable HYSTEN Direct Reg. 108 programmable hysteresis to the loop closure threshold, Voltage-Based Loop LCVE Direct Reg. 108 which can be enabled by setting HYSTEN = 1 (direct Closure Register 108, bit 0). The hysteresis is defined by LCRT (indirect Register 28) and LCRTL (indirect Register 43), Linefeed Calibration
26
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
An internal calibration algorithm corrects for internal and external component errors. The calibration is initiated by setting the CAL bit in direct Register 96. Upon completion of the calibration cycle, this bit is automatically reset. It is recommended that a calibration be executed following system power-up. Upon release of the chip reset, the SI3210 will be in the open state. After powering up the dc-dc converter and allowing it to settle for time (tsettle) the calibration can be initiated. Additional calibrations may be performed, but only one calibration should be necessary as long as the system remains powered up. During calibration, VBAT, VTIP, and VRING voltages are controlled by the calibration engine to provide the correct external voltage conditions for the algorithm. Calibration should be performed in the on-hook state. RING or TIP must not be connected to ground during the calibration. Due to the differences on the driving circuits, there are two different versions of the SI3210. The SI3210 supports the BJT/inductor circuit option, and the SI3210M version supports the MOSFET solution. The only difference between the two versions is the polarity of the DCFF pin with respect to the DCDRV pin. For the SI3210, DCDRV and DCFF are opposite polarity. For the SI3210M, DCDRV and DCFF are the same polarity. Table 25 summarizes these differences.
Table 25. SI3210 and SI3210M Differences
Device DCFF Signal Polarity DCPOL
SI3210 SI3210M
= DCDRV = DCDRV
0 1
Notes: 1. DCFF signal polarity with respect to DCDRV signal. 2. Direct Register 93, bit 5; This is a read-only bit.
Battery Voltage Generation and Switching
The ProSLIC supports two modes of battery supply operation. First, the SI3210 integrates a dc-dc converter controller that dynamically regulates a single output voltage. This mode eliminates the need to supply large external battery voltages. Instead, it converts a single positive input voltage into the real-time battery voltage needed for any given state according to programmed linefeed parameters. Second, the Si3211 and Si3212 support switching between high and low battery voltage supplies, as would a traditional monolithic SLIC. For single to low channel count applications, the SI3210 proves to be an economical choice, as the dc-dc converter eliminates the need to design and build highvoltage power supplies. For higher channel count applications where centralized battery voltage supply is economical, or for modular legacy systems where battery voltage is already available, the Si3211 and Si3212 are recommended.
DC-DC Converter General Description (SI3210/SI3210M Only)
Extensive design guidance on each of these circuits can be obtained from Application Note 45 (AN45) and from an interactive dc-dc converter design spreadsheet. Both of these documents are available on the Silicon Laboratories website (www.silabs.com).
BJT/Inductor Circuit Option Using SI3210
The BJT/Inductor circuit option, as defined in Figure 9, offers a flexible, low-cost solution. Depending on selected L1 inductance value and the switching frequency, the input voltage (VDC) can range from 5 V to 30 V. By nature of a dc-dc converter's operation, peak and average input currents can become large with small input voltages. Consider this when selecting the appropriate input voltage and power rating for the VDC power supply. For this solution, a PNP power BJT (Q7) switches the current flow through low ESR inductor L1. The SI3210 uses the DCDRV and DCFF pins to switch Q7 on and off. DCDRV controls Q7 through NPN BJT Q8. DCFF is ac coupled to Q7 through capacitor C10 to assist R16 in turning off Q7. Therefore, DCFF must have opposite polarity to DCDRV, and the SI3210 (not SI3210M) must be used.
MOSFET/Transformer Circuit Option Using SI3210M
The dc-dc converter dynamically generates the large negative voltages required to operate the linefeed interface. The SI3210 acts as the controller for a buckboost dc-dc converter that converts a positive dc voltage into the desired negative battery voltage. In addition to eliminating external power supplies, this allows the SI3210 to dynamically control the battery voltage to the minimum required for any given mode of operation. Two different dc-dc circuit options are offered: a BJT/ inductor version and a MOSFET/transformer version.
The MOSFET/transformer circuit option, as defined in Figure 11, offers higher power efficiencies across a larger input voltage range. Depending on the transformers primary inductor value and the switching frequency, the input voltage (VDC) can range from 3.3 V to 35 V. Therefore, it is possible to power the entire ProSLIC solution from a single 3.3 V or 5 V power supply. By nature of a dc-dc converter's operation, peak
Preliminary Rev. 1.11
27
Si 3210/ Si3 211/S i32 12
and average input currents can become large with small input voltages. Consider this when selecting the appropriate input voltage and power rating for the VDC power supply (number of REN supported). For this solution, an n-channel power MOSFET (M1) switches the current flow through a power transformer T1. T1 is specified in Application Note 45 (AN45), and includes several taps on the primary side to facilitate a wide range of input voltages. The SI3210M version of the SI3210 must be used for the application circuit depicted in Figure 9 because the DCFF pin is used to drive M1 directly and therefore must be the same polarity as DCDRV. DCDRV is not used in this circuit option; connecting DCFF and DCDRV together is not recommended.
DC-DC Converter Architecture (SI3210/SI3210M Only)
Monitor pins detect an overload condition, the dc-dc converter interrupts its conversion cycles regardless of the register settings to prevent component damage. These inputs should be calibrated by writing the DCCAL bit (bit 7) of the dc-dc Converter Switching Delay register, direct Register 93, after the dc-dc converter has been turned on. Because the SI3210 dynamically regulates its own battery supply voltage using the dc-dc converter controller, the battery voltage (VBAT) is offset from the negative-most terminal by a programmable voltage (VOV) to allow voltage headroom for carrying audio signals. As mentioned previously, the SI3210 dynamically adjusts VBAT to suit the particular circuit requirement. To illustrate this, the behavior of VBAT in the active state is shown in Figure 17. In the active state, the TIP-to-RING open circuit voltage is kept at VOC in the constant voltage region while the regulator output voltage, VBAT = VCM + VOC + VOV. When the loop current attempts to exceed ILIM, the dc line driver circuit enters constant current mode allowing the TIP to RING voltage to track RLOOP. As the TIP terminal is kept at a constant voltage, it is the RING terminal voltage that tracks RLOOP and, as a result, the |VBAT| voltage will also track RLOOP. In this state, |VBAT| = ILIM RLOOP + VCM +VOV. As RLOOP decreases below the VOC/ILIM mark, the regulator output voltage can continue to track RLOOP (TRACK = 1), or the RLOOP tracking mechanism is stopped when |VBAT| = |VBATL| (TRACK = 0). The former case is the more common application and provides the maximum power dissipation savings. In principle, the regulator output voltage can go as low as |VBAT| = VCM+ VOV, offering significant power savings. When TRACK = 0, |VBAT| will not decrease below VBATL. The RING terminal voltage, however, continues to decrease with decreasing RLOOP. The power dissipation on the NPN bipolar transistor driving the RING terminal can become large and may require a higher power rating device. The non-tracking mode of operation is required by specific terminal equipment which, in order to initiate certain data transmission modes, goes briefly on-hook to measure the line voltage to determine whether there is any other off-hook terminal equipment on the same line. TRACK = 0 mode is desired since the regulator output voltage has long settling time constants (on the order of tens of milliseconds) and cannot change rapidly for TRACK = 1 mode. Therefore, the brief on-hook voltage measurement would yield approximately the same voltage as the off-hook line voltage and would cause the terminal equipment to incorrectly sense another offhook terminal.
The control logic for a pulse width modulated (PWM) dcdc converter is incorporated in the SI3210. Output pins, DCDRV and DCFF, are used to switch a bipolar transistor or MOSFET. The polarity of DCFF is opposite to that of DCDRV. The dc-dc converter circuit is powered on when the DCOF bit in the Power Down Register (direct Register 14, bit 4) is cleared to 0. The switching regulator circuit within the SI3210 is a high performance, pulse-width modulation controller. The control pins are driven by the PWM controller logic in the SI3210. The regulated output voltage (VBAT) is sensed by the SVBAT pin and is used to detect whether the output voltage is above or below an internal reference for the desired battery voltage. The dc monitor pins SDCH and SDCL monitor input current and voltage to the dc-dc converter external circuitry. If an overload condition is detected, the PWM controller will turn off the switching transistor for the remainder of a PWM period to prevent damage to external components. It is important that the proper value of R18 be selected to ensure safe operation. Guidance is given in Application Note 45 (AN45). The PWM controller operates at a frequency set by the dc-dc Converter PWM register (direct Register 92). During a PWM period the outputs of the control pins DCDRV and DCFF are asserted for a time given by the read-only PWM Pulse Width register (direct Register 94). The dc-dc converter must be off for some time in each cycle to allow the inductor or transformer to transfer its stored energy to the output capacitor, C9. This minimum off time can be set through the dc-dc Converter Switching Delay register, (direct Register 93). The number of 16.384 MHz clock cycles that the controller is off is equal to DCTOF (bits 0 through 4) plus 4. If the dc
28
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
VOC ILIM VCM VTIP
Constant I Region
Constant V Region
RLOOP
TR
AC K
VBATL
=1
|VTIP - VRING|
VOV
VOC
TRACK=0
VRING VOV VBAT V
Figure 17. VTIP, VRING, and VBAT in the Forward Active State
Table 26. Associated Relevant DC-DC Converter Registers
Parameter Range Resolution Register Bit Location
DC-DC Converter Power-off Control DC-DC Converter Calibration Enable/Status DC-DC Converter PWM Period DC-DC Converter Min. Off Time High Battery Voltage--VBATH Low Battery Voltage--VBATL VOV
n/a n/a 0 to 15.564 us (0 to 1.892 us) + 4 ns 0 to -94.5 V 0 to -94.5 V 0 to -9 V or 0 to -13.5 V
n/a n/a 61.035 ns 61.035 ns 1.5 V 1.5 V 1.5 V
DCOF DCCAL DCN[7:0] DCTOF[4:0] VBATH[5:0] VBATL[5:0] VMIND[3:0] VOV
Direct Register 14 Direct Register 93 Direct Register 92 Direct Register 93 Direct Register 74 Direct Register 75 Indirect Register 41 Direct Register 66
Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly. An "indirect" register is one that is accessed using the indirect access registers (direct registers 28 through 31).
Preliminary Rev. 1.11
29
Si 3210/ Si3 211/S i32 12
DC-DC Converter Enhancements
Tone Generation
Two digital tone generators are provided in the ProSLIC. They allow the generation of a wide variety of single or dual tone frequency and amplitude combinations and spare the user the effort of generating the required POTS signaling tones on the PCM highway. DTMF, FSK (caller ID), call progress, and other tones can all be generated on-chip. The tones can be sent to either the receive or transmit paths (see Figure 23 on page 40).
Tone Generator Architecture
Silicon revisions C and higher support two enhancements to the dc-dc converter. The first is a multi-threshold error control algorithm that enables the dc-dc converter to adjust more quickly to voltage changes. This option is enabled by setting DCSU = 1 (direct Register 108, bit 5). The second enhancement is an audio band filter that removes audio band noise from the dc-dc converter control loop. This option is enabled by setting DCFIL = 1 (direct Register 108, bit 1).
DC-DC Converter During Ringing
When the ProSLIC enters the ringing state, it requires voltages well above those used in the active mode. The voltage to be generated and regulated by the dc-dc converter during a ringing burst is set using the VBATH register (direct Register 74). VBATH can be set between 0 and -94.5 V in 1.5 V steps. To avoid clipping the ringing signal, VBATH must be set larger than the ringing amplitude. At the end of each ringing burst the dc-dc converter adjusts back to active state regulation as described above.
External Battery Switching (Si3211 and Si3212 Only)
A simplified diagram of the tone generator architecture is shown in Figure 18. The oscillator, active/inactive timers, interrupt block, and signal routing block are connected to give the user flexibility in creating audio signals. Control and status register bits are placed in the figure to indicate their association with the tone generator architecture. These registers are described in more detail in Table 27.
The Si3211 and Si3212 support switching between two battery voltages. The circuit for external battery switching is defined in Figure 12. Typically a high voltage battery (e.g., -70 V) is used for on-hook and ringing states, and a low voltage battery (e.g., -24 V) is used for the off-hook condition. The ProSLIC uses an external transistor to switch between the two supplies. When the ProSLIC changes operating states, it automatically switches battery supplies if the automatic/ manual control bit ABAT (direct Register 67, bit 3) is set. For example, the ProSLIC will switch from high battery to low battery when it detects an off-hook event through either a ring trip or loop closure event. If automatic battery selection is disabled (ABAT = 0), the battery is selected by the Battery Feed Select bit, BATSL (direct Register 66, bit 1). Silicon revisions C and higher support the option to add a 60 ms debounce period to the battery switching circuit when transitioning from high battery to low battery. This option is enabled by setting SWDB = 1 (direct Register 108, bit 3). This debounce minimizes battery transitions in the case of pulse dialing or other quick onhook to off-hook transitions.
30
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
8 kHz Clock OnE Zero Cross Logic OZn Zero Cross O SSn
Enable
8 kHz Clock to TX Path
16-Bit Modulo Counter
OA T Expire OIT Expire
Load Logic
Two-Pole Resonance R egister Oscillator
Load
Signal Routing
to RX Path
OAT n O ATnE OITn O ITnE INT Logic INT Logic OnIP REL*
O SCn O nSO O nIE O nAP O SCnY O SCnX
O nAE *Tone G enerator 1 O nly n = "1" or "2" for Tone Generator 1 and 2, respectively
Figure 18. Simplified Tone Generator Diagram
Oscillator Frequency and Amplitude
21336 coeff2 = cos -------------------- = 0.49819 8000
Each of the two tone generators contains a two-pole resonate oscillator circuit with a programmable frequency and amplitude, which are programmed via indirect registers OSC1, OSC1X, OSC1Y, OSC2, OSC2X, and OSC2Y. The sample rate for the two oscillators is 8000 Hz. The equations are as follows: coeffn = cos(2 fn/8000 Hz), where fn is the frequency to be generated; OSCn = coeffn (215);
Desired V RMS 15 1 1 - coeff OSCnX = -- ----------------------- ( 2 - 1 ) --------------------------------------1.11 V RMS 4 1 + coeff
OSC2 = 0.49819 (215) = 16324 = 3FC4h
1 15 0.50181 OSC2X = -- --------------------- ( 2 - 1 ) 0.5 = 2370 = 942h 4 1.49819
OSC2Y = 0 The computed values above would be written to the corresponding registers to initialize the oscillators. Once the oscillators are initialized, the oscillator control registers can be accessed to enable the oscillators and direct their outputs.
Tone Generator Cadence Programming
where desired Vrms is the amplitude to be generated; OSCnY = 0, n = 1 or 2 for oscillator 1 or oscillator 2, respectively. For example, in order to generate a DTMF digit of 8, the two required tones are 852 Hz and 1336 Hz. Assuming the generation of half-scale values (ignoring twist) is desired, the following values are calculated:
2852 coeff1 = cos ---------------- = 0.78434 8000 OSC1 = 0.78434 ( 2 ) = 25701 = 6465h 1 15 0.21556 OSC1X = -- -------------------- ( 2 - 1 ) 0.5 = 1424 = 590h 4 1.78434
15

Each of the two tone generators contains two timers, one for setting the active period and one for setting the inactive period. The oscillator signal is generated during the active period and suspended during the inactive period. Both the active and inactive periods can be programmed from 0 to 8 seconds in 125 s steps. The active period time interval is set using OAT1 (direct registers 36 and 37) for tone generator 1 and OAT2 (direct registers 40 and 41) for tone generator 2. To enable automatic cadence for tone generator 1, define the OAT1 and OIT1 registers and then set the O1TAE bit (direct Register 32, bit 4) and O1TIE bit (direct Register 32, bit 3). This enables each of the timers to control the state of the Oscillator Enable bit, O1E (direct Register 32, bit 2). The 16-bit counter will begin counting until the active timer expires, at which
OSC1Y = 0
Preliminary Rev. 1.11


31
Si 3210/ Si3 211/S i32 12
time the 16-bit counter will reset to zero and begin counting until the inactive timer expires. The cadence continues until the user clears the O1TAE and O1TIE control bits. The zero crossing detect feature can be implemented by setting the OZ1 bit (direct Register 32, bit 5). This ensures that each oscillator pulse ends without a dc component. The timing diagram in Figure 19 is an example of an output cadence using the zero crossing feature. One-shot oscillation can be achieved by enabling O1E and O1TAE. Direct control over the cadence can be achieved by controlling the O1E bit (direct Register 32, bit 2) directly if O1TAE and O1TIE are disabled. The operation of tone generator 2 is identical to that of tone generator 1 using its respective control registers.
Note: Tone Generator 2 should not be enabled simultaneously with the ringing oscillator due to resource sharing within the hardware.
Continuous phase frequency-shift keying (FSK) waveforms may be created using tone generator 1 (not available on tone generator 2) by setting the REL bit (direct Register 32, bit 6), which enables reloading of the OSC1, OSC1X, and OSC1Y registers at the expiration of the active timer (OAT1).
Table 27. Associated Tone Generator Registers
Tone Generator 1 Parameter Description / Range Register Bits Location
Oscillator 1 Frequency Coefficient Oscillator 1 Amplitude Coefficient Oscillator 1 initial phase coefficient Oscillator 1 Active Timer Oscillator 1 Inactive Timer Oscillator 1 Control
Sets oscillator frequency Sets oscillator amplitude Sets initial phase 0 to 8 sec 0 to 8 sec Status and control registers
Tone Generator 2
OSC1[15:0] OSC1X[15:0] OSC1Y[15:0] OAT1[15:0] OIT1[15:0] OSS1, REL, OZ1, O1TAE, O1TIE, O1E, O1SO[1:0]
Register
Indirect Register 13 Indirect Register 14 Indirect Register 15 Direct Registers 36 & 37 Direct Register 38 & 39 Direct Register 32
Parameter
Description / Range
Location
Oscillator 2 Frequency Coefficient Oscillator 2 Amplitude Coefficient Oscillator 2 initial phase coefficient Oscillator 2 Active Timer Oscillator 2 Inactive Timer Oscillator 2 Control
Sets oscillator frequency Sets oscillator amplitude Sets initial phase 0 to 8 sec 0 to 8 sec Status and control registers
OSC2[15:0] OSC2X[15:0] OSC2Y[15:0] OAT2[15:0] OIT2[15:0] OSS2, OZ2, O2TAE, O2TIE, O2E, O2SO[1:0]
Indirect Register 16 Indirect Register 17 Indirect Register 18 Direct Registers 40 & 41 Direct Register 42 & 43 Direct Register 33
32
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
O1E
0,1
...
..., OAT1 0,1 ...
..., O IT1 0,1 ...
..., OAT1 0,1 ...
... ...
OSS1
Tone Gen. 1 Signal Output
Figure 19. Tone Generator Timing Diagram
Enhanced FSK Waveform Generation
Silicon revisions C and higher support enhanced FSK generation capabilities, which can be enabled by setting FSKEN = 1 (direct Register 108, bit 6) and REN = 1 (direct Register 32, bit 6). In this mode, the user can define mark (1) and space (0) attributes once during initialization by defining indirect registers 99-104. The user need only indicate 0-to-1 and 1-to-0 transitions in the information stream. By writing to FSKDAT (direct Register 52), this mode applies a 24 kHz sample rate to tone generator 1 to give additional resolution to timers and frequency generation. Application Note 32 gives detailed instructions on how to implement FSK in this mode. Additionally, sample source code is available from Silicon Laboratories upon request.
Tone Generator Interrupts
ringing cadence. Both sinusoidal and trapezoidal ringing waveforms are supported, and the trapezoidal crest factor is programmable. Ringing signals of up to 88 V peak or more can be generated, enabling the ProSLIC to drive a 5 REN (1380 + 40 F) ringer load across loop lengths of 2000 feet (160 ) or more.
Ringing Architecture
Both the active and inactive timers can generate their own interrupt to signal "on/off" transitions to the software. The timer interrupts for tone generator 1 can be individually enabled by setting the O1AE and O1IE bits (direct Register 21, bits 0 and 1, respectively). Timer interrupts for tone generator two are O2AE and O2IE (direct Register 21, bits 2 and 3, respectively). A pending interrupt for each of the timers is determined by reading the O1AP, O1IP, O2AP, and O2IP bits in the Interrupt Status 1 register (direct Register 18, bits 0 through 3, respectively).
The ringing generator architecture is nearly identical to that of the tone generator. The sinusoid ringing waveform is generated using an internal two-pole resonance oscillator circuit with programmable frequency and amplitude. However, since ringing frequencies are very low compared to the audio band signaling frequencies, the ringing waveform is generated at a 1 kHz rate instead of 8 kHz. The ringing generator has two timers that function the same as for the tone generator timers. They allow on/off cadence settings up to 8 sec on/ 8 sec off. In addition to controlling ringing cadence, these timers control the transition into and out of the ringing state. Table 28 summarizes the list of registers used for ringing generation.
Note: Tone generator 2 should not be enabled concurrently with the ringing generator due to resource sharing within the hardware.
Ringing Generation
The ProSLIC provides fully programmable internal balanced ringing with or without a dc offset to ring a wide variety of terminal devices. All parameters associated with ringing are software programmable: ringing frequency, waveform, amplitude, dc offset, and
Preliminary Rev. 1.11
33
Si 3210/ Si3 211/S i32 12
Table 28. Registers for Ringing Generation
Parameter Range/ Description Register Bits TSWS RVO Location
Ringing Waveform Ringing Voltage Offset Enable Ringing Active Timer Enable Ringing Inactive Timer Enable Ringing Oscillator Enable Ringing Oscillator Active Timer Ringing Oscillator Inactive Timer Linefeed Control (Initiates Ringing State) High Battery Voltage Ringing dc voltage offset Ringing frequency Ringing amplitude Ringing initial phase
Sine/Trapezoid Enabled/ Disabled Enabled/ Disabled Enabled/ Disabled Enabled/ Disabled 0 to 8 sec 0 to 8 sec Ringing State = 100b 0 to -94.5 V 0 to 94.5 V 15 to 100 Hz 0 to 94.5 V Sets initial phase for sinewave and period for trapezoid 0 to 22.5 V
Direct Register 34 Direct Register 34 Direct Register 34 Direct Register 34 Direct Register 34 Direct Registers 48 and 49 Direct Registers 50 and 51 Direct Register 64 Direct Register 74 Indirect Register 19 Indirect Register 20 Indirect Register 21 Indirect Register 22
RTAE RTIE ROE RAT[15:0] RIT[15:0] LF[2:0] VBATH[5:0] ROFF[15:0] RCO[15:0] RNGX[15:0] RNGY[15:0]
Common Mode Bias Adjust During Ringing
VCMR[3:0]
Indirect Register 40
Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly. An "indirect" register is one that is accessed using the indirect access registers (direct registers 28 through 31).
When the ringing state is invoked by writing LF[2:0] = 100 (direct Register 64), the ProSLIC will go into the ringing state and start the first ring. At the expiration of RAT, the ProSLIC will turn off the ringing waveform and will go to the on-hook transmission state. At the expiration of RIT, ringing will again be initiated. This process will continue as long as the two timers are enabled and the Linefeed Control register is set to the ringing state.
Sinusoidal Ringing
and f = desired ringing frequency in hertz.
1 1 - coeff 15 Desired V PK ( 0 to 94.5 V ) RNGX = -- ----------------------- 2 ----------------------------------------------------------------------96 V 4 1 + coeff RNGY = 0
RCO = 0.99211 ( 2 ) = 32509 = 7EFDh RCO = coeff ( 2
15
15
)
where

1 0.00789 15 70 RNGX = -- --------------------- 2 ------ = 376 = 0177h 4 96 1.99211 2f coeff = cos ---------------------1000 Hz

RNGY = 0
34
Preliminary Rev. 1.11


To configure the ProSLIC for sinusoidal ringing, the frequency and amplitude are initialized by writing to the following indirect registers: RCO, RNGX, and RNGY. The equations for RCO, RNGX, RNGY are as follows:
In selecting a ringing amplitude, the peak TIP-to-RING ringing voltage must be greater than the selected onhook line voltage setting (VOC, direct Register 72). For example, to generate a 70 VPK 20 Hz ringing signal, the equations are as follows:
2 20 coeff = cos ---------------------- = 0.99211 1000 Hz
SI3210/Si3211/Si3212
In addition, the user must select the sinusoidal ringing waveform by writing TSWS = 0 (direct Register 34, bit 0).
Trapezoidal Ringing
71 15 RNGX ( 71 V PK ) = ----- 2 = 24235 = 5EABh 96
For a crest factor of 1.3 and a period of 0.05 sec (20 Hz), the rise time requirement is 0.0153 sec.
RCO ( 20 Hz, 1.3 crest factor ) 2 24235 = ----------------------------------- = 396 = 018Ch 0.0153 8000
In addition to the sinusoidal ringing waveform, the ProSLIC supports trapezoidal ringing. Figure 20 illustrates a trapezoidal ringing waveform with offset VROFF.
VTIP-RING
In addition, the user must select the trapezoidal ringing waveform by writing TSWS = 1 in direct Register 34.
Ringing DC voltage Offset
VROFF T=1/freq
tRISE
A dc offset can be added to the ac ringing waveform by defining the offset voltage in ROFF (indirect Register 19). The offset, VROFF, is added to the ringing signal when RVO is set to 1 (direct Register 34, bit 1). The value of ROFF is calculated as follows:
time
V ROFF 15 ROFF = ----------------- 2 96
Linefeed Considerations During Ringing
Figure 20. Trapezoidal Ringing Waveform
To configure the ProSLIC for trapezoidal ringing, the user should follow the same basic procedure as in the Sinusoidal Ringing section, but using the following equations:
1 RNGY = -- Period 8000 2 Desired V PK 15 RNGX = ----------------------------------- ( 2 ) 96 V 2 RNGX RCO = ------------------------------t R ISE 8000
Care must be taken to keep the generated ringing signal within the ringing voltage rails (GNDA and VBAT) to maintains proper biasing of the external bipolar transistors. If the ringing signal nears the rails, a distorted ringing signal and excessive power dissipation in the external transistors will result. To prevent this invalid operation, set the VBATH value (direct Register 74) to a value higher than the maximum peak ringing voltage. The discussion below outlines the considerations and equations that govern the selection of the VBATH setting for a particular desired peak ringing voltage. First, the required amount of ringing overhead voltage, VOVR, is calculated based on the maximum value of current through the load, ILOAD,PK, the minimum current gain of Q5 and Q6, and a reasonable voltage required to keep Q5 and Q6 out of saturation. For ringing signals up to VPK = 87 V, VOVR = 7.5 V is a safe value. However, to determine VOVR for a specific case, use the equations below.
V AC ,PK N R EN I LOAD,PK = ------------------ + IOS = V AC,PK ----------------- + I OS R LOAD 6.9 k
RCO is a value which is added or subtracted from the waveform to ramp the signal up or down in a linear fashion. This value is a function of rise time, period, and amplitude, where rise time and period are related through the following equation for the crest factor of a trapezoidal waveform.

3 1t RI SE = -- T 1 - ---------2 4 CF

where: NREN is the ringing REN load (max value = 5), IOS is the offset current flowing in the line driver circuit (max value = 2 mA), and VAC,PK = amplitude of the ac ringing waveform. It is good practice to provide a buffer of a few more milliamperes for ILOAD,PK to account for possible line
35
where T = ringing period, and CF = desired crest factor. For example, to generate a 71 VPK, 20 Hz ringing signal, the equations are as follows:
1 1 RNGY ( 20 Hz ) = -- --------------- 8000 = 200 = C8h 2 20 Hz
Preliminary Rev. 1.11
Si 3210/ Si3 211/S i32 12
leakages, etc. The total ILOAD,PK current should be smaller than 80 mA.
+1 V OVR = I LOAD,PK ------------ 80.6 + 1 V
where is the minimum expected current gain of transistors Q5 and Q6. The minimum value for VBATH is therefore given by the following:
VBATH = V AC,PK + V ROFF + V OVR
Register 40 should be set with the calculated VOVR to provide voltage headroom during ringing. Silicon revisions C and higher support the option to briefly increase the maximum differential current limit between the voltage transition of TIP and RING from ringing to a dc linefeed state. This mode is enabled by setting ILIMEN = 1 (direct Register 108, bit 7).
Ring Trip Detection
The ProSLIC is designed to create a fully balanced ringing waveform, meaning that the TIP and RING common mode voltage, (VTIP + VRING)/2, is fixed. This voltage is referred to as VCM_RING and is automatically set to the following:
VBATH - VCMR VCM_RING = --------------------------------------------2
VCMR is an indirect register which provides the headroom by the ringing waveform with respect to the VBATH rail. The value is set as a 4-bit setting in indirect Register 40 with an LSB voltage of 1.5 V/LSB.
Input Signal Processor
A ring trip event signals that the terminal equipment has gone off-hook during the ringing state. The ProSLIC performs ring trip detection digitally using its on-chip monitor A/D converter. The functional blocks required to implement ring trip detection is shown in Figure 21. The primary input to the system is the Loop Current Sense value provided by the current monitoring circuitry and reported in direct Register 79. LCS data is processed by the input signal processor when the ProSLIC is in the ringing state as indicated by the Linefeed Shadow register (direct Register 64). The data then feeds into a programmable digital low pass filter, which removes unwanted ac signal components before threshold detection.
LCS
ISP_OUT
Digital LPF
+
DBIRAW
Debounce Filter
R TP
Interrupt Logic
R TIP
- N RTP LFS Ring Trip Threshold RTDI RTIE
R PTP
Figure 21. Ring Trip Detector
The output of the low pass filter is compared to a programmable threshold, RPTP (indirect Register 29). The threshold comparator output feeds a programmable debouncing filter. The output of the debouncing filter remains in its present state unless the input remains in the opposite state for the entire period of time programmed by the ring trip debounce interval, RTDI[6:0] (direct Register 70). If the debounce interval has been satisfied, the RTP bit of direct Register 68 will be set to indicate that a valid ring trip has occurred. A ring trip interrupt is generated if enabled by the RTIE bit (direct Register 22). Table 29 lists the registers that must be written or monitored to correctly detect a ring
36
trip condition. The recommended values for RPTP, NRTP, and RTDI vary according to the programmed ringing frequency. Register values for various ringing frequencies are given in Table 30.
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 29. Associated Registers for Ring Trip Detection
Parameter Register Location
Ring Trip Interrupt Pending Ring Trip Interrupt Enable Ring Trip Detect Debounce Interval Ring Trip Threshold Ring Trip Filter Coefficient Ring Trip Detect Status (monitor only)
RTIP RTIE RTDI[6:0] RPTP[5:0] NRTP[12:0] RTP
Direct Register 19 Direct Register 22 Direct Register 70 Indirect Register 29 Indirect Register 36 Direct Register 68
Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly. An "indirect" register is one that is accessed using the indirect access registers (direct registers 28 through 31).
Table 30. Recommended Ring Trip Values for Ringing
Ringing Frequency NRTP RPTP RTDI
Hz 16.667 20 30 40 50 60
decimal 64 100 112 128 213 256
hex 0200 0320 0380 0400 06A8 0800
decimal 34 mA 34 mA 34 mA 34 mA 34 mA 34 mA
hex 3600 3600 3600 3600 3600 3600
decimal 15.4 ms 12.3 ms 8.96 ms 7.5 ms 5 ms 4.8 ms
hex 0F 0B 09 07 05 05
Pulse Metering Generation
There is an additional tone generator suitable for generating tones above the audio frequency. This oscillator is provided for the generation of billing tones which are typically 12 kHz or 16 kHz. The generator follows the same algorithm as described in "Tone Generation" on page 30 with the exception that the sample rate for computation is 64 kHz instead of 8 kHz. The equations are as follows:

Desired V RMS 15 1 1 - coeff PLSX = -- ----------------------- ( 2 - 1 ) ---------------------------------------------Full Scale V RMS 4 1 + coeff
where full scale VRMS = 0.85 VRMS for a matched load. The initial phase of the pulse metering signal is set to 0 internally so there is no register to serve this purpose. The pulse metering generator timers and associated pulse metering timer registers are similar to that of the tone generators. These timers count 8 kHz sample periods like the other tones even though the sinusoid is generated at 64 kHz.
2f coeff = cos ------------------------64000 Hz PLSCO = coeff ( 2

15
- 1)
Preliminary Rev. 1.11
37
Si 3210/ Si3 211/S i32 12
Table 31. Associated Pulse Metering Generator Registers
Parameter Description / Range Register Bits Location
Pulse Metering Frequency Coefficient Pulse Metering Amplitude Coefficient Pulse Metering Attack/Decay Ramp Rate Pulse Metering Active Timer Pulse Metering Inactive Timer Pulse Metering Control
Sets oscillator frequency Sets oscillator amplitude 0 to PLSX (full amplitude) 0 to 8 sec 0 to 8 sec Status and control registers
PLSCO[15:0] PLSX[15:0] PLSD[15:0] PAT[15:0] PIT[15:0] PSTAT, PMAE, PMIE, PMOE
Indirect Register 25 Indirect Register 24 Indirect Register 23 Direct Registers 44 & 45 Direct Register 46 & 47 Direct Register 35
Note: The ProSLIC uses registers that are both directly and indirectly mapped. A "direct" register is one that is mapped directly. An "indirect" register is one that is accessed using the indirect access registers (direct registers 28 through 31).
The pulse metering oscillator has a volume envelope (linear ramp) on the on/off transitions of the oscillator. The volume value is incremented by the value in the PLSD register (indirect Register 23) at an 8 kHz rate. The sinusoidal generator output is multiplied by this volume before being sent to the DAC. The volume will ramp from 0 to 7FFF in increments of PLSD so the value of PLSD will set the slope of the ramp. When the pulse metering signal is turned off, the volume will ramp to 0 by decrementing according to the value of PLSD.
DTMF Detection
The dual-tone multi-frequency (DTMF) tone signaling standard is also known as touch tone. It is an in-band signaling system used to replace the pulse-dial signaling standard. In DTMF, two tones are used to generate a DTMF digit. One tone is chosen from four possible row tones, and one tone is chosen from four possible column tones. The sum of these tones constitutes one of 16 possible DTMF digits.
DTMF Detection Architecture
Pulse Metering Oscillator
X
To DAC Volum e 8 Khz
+/-
PLSD
DTMF detection is performed using a modified Goertzel algorithm to compute the dual frequency tone (DFT) for each of the eight DTMF frequencies as well as their second harmonics. At the end of the DFT computation, the squared magnitudes of the DFT results for the eight DTMF fundamental tones are computed. The row results are sorted to determine the strongest row frequency; the column frequencies are sorted as well. At the completion of this process, a number of checks are made to determine whether the strongest row and column tones constitute a DTMF digit. The detection process is performed twice within the 45 ms minimum tone time. A digit must be detected on two consecutive tests following a pause to be recognized as a new digit. If all tests pass, an interrupt is generated, and the DTMF digit value is loaded into the DTMF register. If tones are occurring at the maximum rate of 100 ms per digit, the interrupt must be serviced within 85 ms so that the current digit is not
Clip to 7FFF or 0
Figure 22. Pulse Metering Volume Envelope
38
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
overwritten by a new one. There is no buffering of the digit information.
Audio Path
Unlike traditional SLICs, the codec function is integrated into the ProSLIC. The 16-bit codec offers programmable gain/attenuation blocks and several loop-back modes. The signal path block diagram is shown in Figure 23.
Transmit Path
In the transmit path, the analog signal fed by the external ac coupling capacitors is amplified by the analog transmit amplifier, ATX, prior to the A/D converter. The gain of the ATX is user selectable to one of mute/-3.5/0/3.5 dB options. The main role of ATX is to coarsely adjust the signal swing to be as close as possible to the full-scale input of the A/D converter in order to maximize the signal-to-noise ratio of the transmit path. After passing through an anti-aliasing filter, the analog signal is processed by the A/D converter, producing an 8 kHz, 16-bit wide, linear PCM data stream. The standard requirements for transmit path attenuation for signals above 3.4 kHz are implemented as part of the combined decimation filter characteristic of the A/D converter. One more digital filter is available in the transmit path: THPF. THPF implements the high-pass attenuation requirements for signals below 65 Hz. The linear PCM data stream output from THPF is amplified by the transmit-path programmable gain amplifier, ADCG, which can be programmed from - dB to 6 dB. The DTMF decoder can receive the linear PCM data stream at this point to perform the digit extraction when enabled by the user. The final step in the transmit path signal processing is the user selectable A-law or -law compression which can reduce the data stream word width to 8 bits. Depending on the PCM_Mode register selection, every 8-bit compressed serial data word will occupy one time slot on the PCM highway, or every 16-bit uncompressed serial data word will occupy two time slots on the PCM highway.
Preliminary Rev. 1.11
39
40
Transmit Path Off Chip On Chip From Billing Tone DAC HYBP H DTMF Decoder
Si 3210/ Si3 211/S i32 12
ATX
+-
A/D
Decimation Filter
THPF
ADCG
Mute
+
/A-law Compressor
Serial Output
Digital TX
Analog Loopback
Digital Loopback
TXM Full Analog Loopback
H
HYBA
ALM1
DLM
Dual Tone Generator
ALM2
TIP RING
XAC
ARX -
+
From Billing Tone DAC
D/A
Interpolation Filter
RHPF
DACG
+
Mute
/A-law Expander
Serial Input
Digital RX
Preliminary Rev. 1.11
Ibuf
Gm
RAC RXM
Figure 23. AC Signal Path Block Diagram
SI3210/Si3211/Si3212
Receive Path
In the receive path, the optionally compressed 8-bit data is first expanded to 16-bit words. The PCMF register bit can bypass the expansion process, in which case two 8-bit words are assembled into one 16-bit word. DACG is the receive path programmable gain amplifier which can be programmed from - dB to 6 dB. An 8 kHz, 16bit signal is then provided to a D/A converter. The resulting analog signal is amplified by the analog receive amplifier, ARX, which is user selectable to one of mute/-3.5/0/3.5 dB options. It is then applied at the input of the transconductance amplifier (Gm) which drives the off-chip current buffer (IBUF).
Audio Characteristics
should be interpreted as the maximum allowable magnitude of any spurious signals that are generated when a PCM data stream representing a sine wave signal in the range of 300 Hz to 3.4 kHz at a level of 0 dBm0 is applied at the digital input. The group delay distortion in either path is limited to no more than the levels indicated in Figure 5 on page 10. The reference in Figure 5 is the smallest group delay for a sine wave in the range of 500 Hz to 2500 Hz at 0 dBm0. The block diagram for the voice-band signal processing paths are shown in Figure 23. Both the receive and the transmit paths employ the optimal combination of analog and digital signal processing to provide the maximum performance while, at the same time, offering sufficient flexibility to allow users to optimize for their particular application of the ProSLIC. All programmable signal-processing blocks are symbolically indicated in Figure 23 by a dashed arrow across them. The two-wire (TIP/RING) voice-band interface to the ProSLIC is implemented using a small number of external components. The receive path interface consists of a unity-gain current buffer, IBUF, while the transmit path interface is simply an ac coupling capacitor. Signal paths, although implemented differentially, are shown as single-ended for simplicity.
Transhybrid Balance
The dominant source of distortion and noise in both the transmit and receive paths is the quantization noise introduced by the -law or the A-law compression process. Figure 1 on page 7 specifies the minimum signal-to-noise-and-distortion ratio for either path for a sine wave input of 200 Hz to 3400 Hz. Both the -law and the A-law speech encoding allow the audio codec to transfer and process audio signals larger than 0 dBm0 without clipping. The maximum PCM code is generated for a -law encoded sine wave of 3.17 dBm0 or an A-law encoded sine wave of 3.14 dBm0. The ProSLIC overload clipping limits are driven by the PCM encoding process. Figure 2 on page 7 shows the acceptable limits for the analog-to-analog fundamental power transfer-function, which bounds the behavior of ProSLIC. The transmit path gain distortion versus frequency is shown in Figure 3 on page 8. The same figure also presents the minimum required attenuation for any outof-band analog signal that may be applied on the line. Note the presence of a high-pass filter transfer-function, which ensures at least 30 dB of attenuation for signals below 65 Hz. The low-pass filter transfer function which attenuates signals above 3.4 kHz has to exceed the requirements specified by the equations in Figure 3 on page 8 and it is implemented as part of the A-to-D converter. The receive path transfer function requirement, shown in Figure 4 on page 9, is very similar to the transmit path transfer function. The most notable difference is the absence of the high-pass filter portion. The only other differences are the maximum 2 dB attenuation at 200 Hz (as opposed to 3 dB for the transmit path) and the 28 dB of attenuation for any frequency above 4.6 kHz. The PCM data rate is 8 kHz and thus, no frequencies greater than 4 kHz can be digitally encoded in the data stream. From this point of view, at frequencies greater than 4 kHz, the plot in Figure 4
The ProSLIC provides programmable transhybrid balance with gain block H. (See Figure 23.) In the ideal case where the synthesized SLIC impedance matches exactly the subscriber loop impedance, the transhybrid balance should be set to subtract a -6 dB level from the transmit path signal. The transhybrid balance gain can be adjusted from -2.77 dB to +4.08 dB around the ideal setting of -6 dB by programming the HYBA[2:0] bits of the Hybrid Control register (direct Register 11). Note that adjusting any of the analog or digital gain blocks will not require any modification of the transhybrid balance gain block, as the transhybrid gain is subtracted from the transmit path signal prior to any gain adjustment stages. The transhybrid balance can also be disabled, if desired, using the appropriate register setting.
Loopback Testing
Four loopback test options are available in the ProSLIC: The full analog loopback (ALM2) tests almost all the circuitry of both the transmit and receive paths. The compressed 8-bit word transmit data stream is fed back serially to input of the receive path expander. (See Figure 23.) The signal path starts with the analog signal at the input of the transmit path and ends with an analog signal at the output of the
Preliminary Rev. 1.11
41
Si 3210/ Si3 211/S i32 12
receive path. An additional analog loopback (ALM1) takes the digital stream at the output of the A/D converter and feeds it back to the D/A converter. (See Figure 23.) The signal path starts with the analog signal at the input of the transmit path and ends with an analog signal at the output of the receive path. This loopback option allows the testing of the analog signal processing circuitry of the SI3210 completely independent from any activity in the DSP. The full digital loopback tests almost all the circuitry of both the transmit and receive paths. The analog signal at the output of the receive path is fed back to the input of the transmit path by way of the hybrid filter path. (See Figure 23.) The signal path starts with 8-bit PCM data input to the receive path and ends with 8-bit PCM data at the output of the transmit path. The user can bypass the companding process and interface directly to the 16-bit data. An additional digital loopback (DLM) takes the digital stream at the input of the D/A converter in the receive path and feeds it back to the transmit A/D digital filter. The signal path starts with 8-bit PCM data input to the receive path and ends with 8-bit PCM data at the output of the transmit path. This loopback option allows the testing of the digital signal processing circuitry of the SI3210 completely independent from any analog signal processing activity.The user can bypass the companding process and interface directly to the 16-bit data. The ProSLIC also provides a means to compensate for degraded subscriber loop conditions involving excessive line capacitance (leakage). The CLC[1:0] bits of direct Register 10 increase the ac signal magnitude to compensate for the additional loss at the high end of the audio frequency range. The default setting of CLC[2:0] assumes no line capacitance. Silicon revisions C and higher support the option to remove the internal reference resistor used to synthesize ac impedances for 600 + 2.16 F and 900 + 2.16 F settings so that an external resistor reference may be used. This option is enabled by setting ZSEXT = 1 (direct Register 108, bit 4).
Clock Generation
The ProSLIC will generate the necessary internal clock frequencies from the PCLK input. PCLK must be synchronous to the 8 kHz FSYNC clock and run at one of the following rates: 256 kHz, 512 kHz, 768 kHz, 1.024 MHz, 1.536 MHz, 2.048 MHz, 4.096 MHz or 8.192 MHz. The ratio of the PCLK rate to the FSYNC rate is determined via a counter clocked by PCLK. The three-bit ratio information is automatically transferred into an internal register, PLL_MULT, following a reset of the ProSLIC. The PLL_MULT is used to control the internal PLL which multiplies PCLK as needed to generate 16.384 MHz rate needed to run the internal filters and other circuitry. The PLL clock synthesizer settles very quickly following power up. However, the settling time depends on the PCLK frequency and it can be approximately predicted by the following equation:
64 T SETTLE = ---------------F PCLK
Two-Wire Impedance Matching
The ProSLIC provides on-chip programmable two-wire impedance settings to meet a wide variety of worldwide two-wire return loss requirements. The two-wire impedance is programmed by loading one of the eight available impedance values into the TISS[2:0] bits of the Two-Wire Impedance Synthesis Control register (direct Register 10). If direct Register 10 is not user-defined, the default setting of 600 will be loaded into the TISS register. Real and complex two-wire impedances are realized by internal feedback of a programmable amplifier (RAC) a switched capacitor network (XAC) and a transconductance amplifier (Gm). (See Figure 23.) RAC creates the real portion and XAC creates the imaginary portion of Gm's input. Gm then creates a current that models the desired impedance value to the subscriber loop. The differential ac current is fed to the subscriber loop via the ITIPP and IRINGP pins through an off-chip current buffer (IBUF), which is implemented using transistor Q1 and Q2 (see Figure on page 16). Gm is referenced to an off-chip resistor (R15).
42
Interrupt Logic
The ProSLIC is capable of generating interrupts for the following events: Loop current/ring ground detected Ring trip detected Power alarm DTMF digit detected (SI3210 and Si3211 only) Active timer 1 expired Inactive timer 1 expired Active timer 2 expired Inactive timer 2 expired Ringing active timer expired Ringing inactive timer expired Pulse metering active timer expired Pulse metering inactive timer expired
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Indirect register access complete The interface to the interrupt logic consists of six registers. Three interrupt status registers contain 1 bit for each of the above interrupt functions. These bits will be set when an interrupt is pending for the associated resource. Three interrupt enable registers also contain 1 bit for each interrupt function. In the case of the interrupt enable registers, the bits are active high. Refer to the appropriate functional description section for operational details of the interrupt functions. When a resource reaches an interrupt condition, it will signal an interrupt to the interrupt control block. The interrupt control block will then set the associated bit in the interrupt status register if the enable bit for that interrupt is set. The INT pin is a NOR of the bits of the interrupt status registers. Therefore, if a bit in the interrupt status registers is asserted, IRQ will assert low. Upon receiving the interrupt, the interrupt handler should read interrupt status registers to determine which resource is requesting service. To clear a pending interrupt, write the desired bit in the appropriate interrupt status register to 1. Writing a 0 has no effect. This provides a mechanism for clearing individual bits when multiple interrupts occur simultaneously. While the interrupt status registers are non-zero, the INT pin will remain asserted. Indirect registers are accessed through direct registers 29 through 30. Instructions on how to access them is described in "Control Registers" beginning on page 50. There are a number of variations of usage on this fourwire interface:
Continuous clocking. During continuous clocking, the data transfers are controlled by the assertion of the CS pin. CS must assert before the falling edge of SCLK on which the first bit of data is expected during a read cycle, and must remain low for the duration of the 8 bit transfer (command/address or data). SDI/SDO wired operation. Independent of the clocking options described, SDI and SDO can be treated as two separate lines or wired together if the master is capable of tristating its output during the data byte transfer of a read operation. Daisy chain mode. This mode allows communication with banks of up to eight ProSLIC devices using one chip select signal. When the SPIDC bit in the SPI Mode Select register is set, data transfer mode changes to a 3-byte operation: a chip select byte, an address/control byte, and a data byte. Using the circuit shown in Figure 26, a single device may select from the bank of devices by setting the appropriate chip select bit to a one. Each device uses the LSB of the chip select byte, shifts the data right by one bit, and passes the chip select byte using the SDITHRU pin to the next device in the chain. Address/control and data bytes are unaltered.
Serial Peripheral Interface
The control interface to the ProSLIC is a 4-wire interface modeled after commonly available micro-controller and serial peripheral devices. The interface consists of a clock (SCLK), chip select (CS), serial data input (SDI), and serial data output (SDO). Data is transferred a byte at a time with each register access consisting of a pair of byte transfers. Figures 24 and 25 illustrate read and write operation in the SPI bus. The first byte of the pair is the command/address byte. The MSB of this byte indicates register read when 1 and a register write when 0. The remaining seven bits of the command/address byte indicate the address of the register to be accessed. The second byte of the pair is the data byte. During a read operation, the SDO becomes active and the 8-bit contents of the register are driven out MSB first. The SDO will be high impedence on either the falling edge of SCLK following the LSB, or the rising of CS whichever comes first. SDI is a "don't care" during the data portion of read operations. During write operations, data is driven into the ProSLIC via the SDI pin MSB first. The SDO pin will remain high impedance during write operations. Data always transitions with the falling edge of the clock and is latched on the rising edge. The clock should return to a logic high when no transfer is in progress.
Preliminary Rev. 1.11
43
Si 3210/ Si3 211/S i32 12
SCLK
Don't Care
CS
SDI
0
a6
a5
a4
a3
a2
a1
a0
d7
d6
d5
d4
d3
d2
d1
d0
SDO High Impedance
Figure 24. Serial Write 8-Bit Mode
SCLK
Don't Care
CS
SDI
1
a6
a5
a4
a3
a2
a1
a0
Don't Care
SDO High Impedance
d7
d6
d5
d4
d3
d2
d1
d0
Figure 25. Serial Read 8-Bit Mode
44
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
SD O CPU CS SD I
CS SDO
SD I
SDI0
SD ITHR U
CS SDO
SD I
SDI1
SD ITHR U
CS SDO
SDI
SDI2
SD ITH RU
CS SDO
SDI
SDI3
SD ITH RU
C hip Select Byte SC LK
Address Byte
Data Byte
SDI0
C7 C6 C5 C4 C3 C2 C1 C0
R /W
A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
SDI1
- C7 C6 C5 C4 C3 C2 C1
R /W
A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
SDI2
-
-
C7 C6 C5 C4 C3 C2
R /W
A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
SDI3
-
-
-
C7 C6 C5 C4 C3
R /W
A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
N ote: During chip select byte, SD ITHR U = SD I delayed by one SC LK. Each device daisy-chained looks at the LSB of the chip select byte for its chip select.
Figure 26. SPI Daisy Chain Mode
Preliminary Rev. 1.11
45
Si 3210/ Si3 211/S i32 12
PCM Interface
The ProSLIC contains a flexible programmable interface for the transmission and reception of digital PCM samples. PCM data transfer is controlled via the PCLK and FSYNC inputs as well as the PCM Mode Select (direct Register 1), PCM Transmit Start Count (direct registers 2 and 3), and PCM Receive Start Count (direct registers 4 and 5) registers. The interface can be configured to support from 4 to 128 8-bit timeslots in each frame. This corresponds to PCLK frequencies of 256 kHz to 8.192 MHz in power of 2 increments. (768 kHz and 1.536 MHz are also available.) Timeslots for data transmission and reception are independently configured using the TXS and RXS registers. By setting the correct starting point of the data, the ProSLIC can be configured to support long FSYNC and short FSYNC variants as well as IDL2 8-bit, 10-bit, B1 and B2 channel time slots. DTX data is high impedance except for the duration of the 8-bit PCM transmit. DTX will return to
P CLK
high impedance either on the negative edge of PCLK during the LSB, or on the positive edge of PCLK following the LSB. This is based on the setting of the TRI bit of the PCM Mode Select register. Tristating on the negative edge allows the transmission of data by multiple sources in adjacent timeslots without the risk of driver contention. In addition to 8-bit data modes, there is a 16-bit mode provided. This mode can be activated via the PCMT bit of the PCM Mode Select register. GCI timing is also supported in which the duration of a data bit is two PCLK cycles. This mode is also activated via the PCM Mode Select register. Setting the TXS or RXS register greater than the number of PCLK cycles in a sample period will stop data transmission because TXS or RXS will never equal the PCLK count. Figures 27-30 illustrate the usage of the PCM highway interface to adapt to common PCM standards.
FSYNC
PCLK_CNT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
DRX
M SB LSB
DTX
HI-Z M SB LSB HI-Z
Figure 27. Example, Timeslot 1, Short FSYNC (TXS/RXS = 1)
PCLK
FSYN C
PC LK_C NT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
DR X
MSB LSB
DTX
H I-Z MSB LSB HI-Z
Figure 28. Example, Timeslot 1, Long FSYNC (TXS/RXS = 0)
46 Preliminary Rev. 1.11
SI3210/Si3211/Si3212
P CLK
F SYNC
PCLK_CNT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
DRX
M SB LSB
DT X
HI-Z M SB LSB
HI-Z
Figure 29. Example, IDL2 Long FSYNC, B2, 10-Bit Mode (TXS/RXS = 10)
PCLK
FSYN C
PC LK_C NT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
DR X
MSB LSB
DTX
H I-Z HI-Z
Figure 30. GCI Example, Timeslot 1 (TXS/RXS = 0)
Companding
The ProSLIC supports both -255 Law and A-Law companding formats in addition to linear data. These 8-bit companding schemes follow a segmented curve formatted as sign bit, three chord bits, and four step bits. -255 Law is more commonly used in North America and Japan, while A-Law is primarily used in Europe. Data format is selected via the PCMF register. Tables 32 and 33 define the -Law and A-Law encoding formats.
Preliminary Rev. 1.11
47
Si 3210/ Si3 211/S i32 12
Table 32. -Law Encode-Decode Characteristics1,2
Segment Number
8
#Intervals X Interval Size
16 X 256
Value at Segment Endpoints
8159 . . . 4319 4063 . . . 2143 2015 . . . 1055 991 . . . 511 479 . . . 239 223 . . . 103 95 . . . 35 31 . . . 3 1 0
Digital Code
10000000b
Decode Level
8031
10001111b
4191
7
16 X 128
10011111b
2079
6
16 X 64
10101111b
1023
5
16 X 32
10111111b
495
4
16 X 16
11001111b
231
3
16 X 8
11011111b
99
2
16 X 4
11101111b
33
1
15 X 2
__________________ 1X1
11111110b 11111111b
2 0
Notes: 1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative analog values. 2. Digital code includes inversion of all magnitude bits.
48
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 33. A-Law Encode-Decode Characteristics1,2
Segment Number #intervals X interval size Value at segment endpoints Digital Code Decode Level
7
16 X 128
4096 3968 . . 2176 2048 . . . 1088 1024 . . . 544 512 . . . 272 256 . . . 136 128 . . . 68 64 . . . 2 0
10101010b
4032
10100101b
2112
6
16 X 64
10110101b
1056
5
16 X 32
10000101b
528
4
16 X 16
10010101b
264
3
16 X 8
11100101b
132
2
16 X 4
11110101b
66
1
32 X 2
11010101b
1
Notes: 1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative values. 2. Digital code includes inversion of all even numbered bits.
Preliminary Rev. 1.11
49
Si 3210/ Si3 211/S i32 12
Control Registers
Note: Any register not listed here is reserved and must not be written.
Table 34. Direct Register Summary
Register Name Bit 7 Bit 6 Bit 5 Setup Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0 1 2 3 4 5 6
SPI Mode Select PCM Mode Select PCM Transmit Start Count--Low Byte PCM Transmit Start Count--High Byte PCM Receive Start Count--Low Byte PCM Receive Start Count--High Byte Digital Input/Output Control
SPIDC
SPIM
PNI[1:0] PCME PCMF[1:0] TXS[7:0]
RNI[3:0] PCMT GCI TRI
TXS[9:8] RXS[7:0] RXS[9:8] DOUT1
Audio
DIO21
DIO11
PD21
PD11
8 9 10 11
Audio Path Loopback Control Audio Gain Control Two-Wire Impedance Synthesis Control Hybrid Control RXHP TXHP TXM RXM
ALM2 ATX[1:0] TISE
DLM
ALM1
ARX[1:0] TISS[2:0] HYBA[2:0]
CLC[1:0] HYBP[2:0]
Powerdown
14 15
Power Down Control 1 Power Down Control 2
PMON ADCM
Interrupts
DCOF2 ADCON
MOF DACM DACON
BIASOF SLICOF GMM GMON
18 19 20 21 22 23 24
Interrupt Status 1 Interrupt Status 2 Interrupt Status 3 Interrupt Enable 1 Interrupt Enable 2 Interrupt Enable 3 Decode Status
PMIP Q6AP
PMAP Q5AP
RGIP Q4AP
RGAP Q3AP
O2IP Q2AP
O2AP Q1AP CMCP
O1IP LCIP INDP O1IE LCIE INDE
O1AP RTIP DTMFP3 O1AE RTIE DTMFE3
PMIE Q6AE
PMAE Q5AE
RGIE Q4AE
RGAE Q3AE VAL3
O2IE Q2AE
O2AE Q1AE CMCE
DIG[3:0]3
Indirect Register Access
Notes: 1. Si3211 and Si3212 only. 2. SI3210 only. 3. SI3210 and Si3211 only.
50
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 34. Direct Register Summary (Continued)
Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
28 29 30 31
Indirect Data Access-- Low Byte Indirect Data Access-- High Byte Indirect Address Indirect Address Status
Oscillators
IDA[7:0] IDA[15:8] IAA[7:0] IAS
32 33 34 35 36 37 38 39 40 41 42 43 44
Oscillator 1 Control Oscillator 2 Control Ringing Oscillator Control Pulse Metering Oscillator Control Oscillator 1 Active Timer--Low Byte Oscillator 1 Active Timer--High Byte Oscillator 1 Inactive Timer--Low Byte Oscillator 1 Inactive Timer--High Byte Oscillator 2 Active Timer--Low Byte Oscillator 2 Active Timer--High Byte Oscillator 2 Inactive Timer--Low Byte Oscillator 2 Inactive Timer--High Byte Pulse Metering Oscillator Active Timer-- Low Byte Pulse Metering Oscillator Active Timer-- High Byte Pulse Metering Oscillator Inactive Timer--Low Byte
OSS1 OSS2 RSS PSTAT
REL
OZ1 OZ2 RDAC
O1TAE O2TAE RTAE PMAE
O1TIE O2TIE RTIE PMIE
O1E O2E ROE PMOE
O1SO[1:0] O2SO[1:0] RVO TSWS
OAT1[7:0] OAT1[15:8] OIT1[7:0] OIT1[15:8] OAT2[7:0] OAT2[15:8] OIT2[7:0] OIT2[15:8] PAT[7:0]
45
PAT[15:8]
46
PIT[7:0]
Notes: 1. Si3211 and Si3212 only. 2. SI3210 only. 3. SI3210 and Si3211 only.
Preliminary Rev. 1.11
51
Si 3210/ Si3 211/S i32 12
Table 34. Direct Register Summary (Continued)
Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
47
Pulse Metering Oscillator Inactive Timer--High Byte Ringing Oscillator Active Timer--Low Byte Ringing Oscillator Active Timer--High Byte Ringing Oscillator Inactive Timer--Low Byte Ringing Oscillator Inactive Timer--High Byte FSK Data
SLIC
PIT[15:8]
48 49 50 51 52
RAT[7:0] RAT[15:8] RIT[7:0] RIT[15:8] FSKDAT
63
Loop Closure Debounce Interval for Automatic Ringing Linefeed Control External Bipolar Transistor Control Battery Feed Control Automatic/Manual Control Loop Closure/Ring Trip Detect Status Loop Closure Debounce Interval Ring Trip Detect Debounce Interval Loop Current Limit On-Hook Line Voltage Common Mode Voltage High Battery Voltage Low Battery Voltage Power Monitor Pointer Line Power Output Monitor Loop Voltage Sense LVSP VSGN MNCM MNDIF SQH LFS[2:0] CBY
LCD[7:0]
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78
LF[2:0] ETBE VOV2 SPDS ETBO[1:0] FVBAT2 ABAT AORD DBIRAW LCDI[6:0] RTDI[6:0] ILIM[2:0] VOC[5:0] VCM[5:0] VBATH[5:0] VBATL[5:0] PWRMP[2:0] PWROM[7:0] LVS[5:0] ETBA[1:0] BATSL1 TRACK2 AOLD RTP AOPN LCR
Notes: 1. Si3211 and Si3212 only. 2. SI3210 only. 3. SI3210 and Si3211 only.
52
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 34. Direct Register Summary (Continued)
Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
79 80 81 82 83 84 85 86 87 88 89 92 93 94 95 96 97 98 99 100
Loop Current Sense TIP Voltage Sense RING Voltage Sense Battery Voltage Sense 1 Battery Voltage Sense 2 Transistor 1 Current Sense Transistor 2 Current Sense Transistor 3 Current Sense Transistor 4 Current Sense Transistor 5 Current Sense Transistor 6 Current Sense DC-DC Converter PWM Period DC-DC Converter Switching Delay PWM Pulse Width Reserved Calibration Control/ Status Register 1 Calibration Control/ Status Register 2 RING Gain Mismatch Calibration Result TIP Gain Mismatch Calibration Result Differential Loop Current Gain Calibration Result Common Mode Loop Current Gain Calibration Result DCCAL2
LCSP VTIP[7:0]
LCS[5:0]
VRING[7:0] VBATS1[7:0] VBATS2[7:0] IQ1[7:0] IQ2[7:0] IQ3[7:0] IQ4[7:0] IQ5[7:0] IQ6[7:0] DCN[7:0]3 DCPOL2 DCPW[7:0]2 DCTOF[4:0]2
CAL
CALSP
CALR
CALM1
CALT
CALM2
CALD
CALDAC
CALC
CALADC
CALIL
CALCM
CALGMR[R4:0] CALGMT[4:0] CALGD[4:0]
101
CALGC[4:0]
Notes: 1. Si3211 and Si3212 only. 2. SI3210 only. 3. SI3210 and Si3211 only.
Preliminary Rev. 1.11
53
Si 3210/ Si3 211/S i32 12
Table 34. Direct Register Summary (Continued)
Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
102 103 104 105 106 107 108
Current Limit Calibration Result Monitor ADC Offset Calibration Result Analog DAC/ADC Offset DAC Offset Calibration Result Common Mode Balance Calibration Result DC Peak Voltage Calibration Result Enhancement Enable ILIMEN FSKEN DCEN2 ZSEXT SWDB CALMG1[3:0] DACP DACOF[7:0]
CALGIL[3:0] CALMG2[3:0] DACN ADCP ADCN
CMBAL[5:0] CMDCPK[3:0] LCVE DCFIL2 HYSTEN
Notes: 1. Si3211 and Si3212 only. 2. SI3210 only. 3. SI3210 and Si3211 only.
54
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 0. SPI Mode Select Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
SPIDC R/W
SPIM R/W
PNI[1:0] R
RNI[3:0] R
Reset settings = 00xx_xxxx
Bit Name Function SPI Daisy Chain Mode Enable. 0 = Disable SPI daisy chain mode. 1 = Enable SPI daisy chain mode. SPI Mode. 0 = Causes SDO to tri-state on rising edge of SCLK of LSB. 1 = Normal operation; SDO tri-states on rising edge of CS. Part Number Identification. 00 = SI3210 01 = Si3211 10 = Si3212 11 = SI3210M Revision Number Identification. 0001 = Revision A, 0010 = Revision B, 0011 = Revision C, etc.
7
SPIDC
6
SPIM
5:4
PNI[1:0]
3:0
RNI[3:0]
Preliminary Rev. 1.11
55
Si 3210/ Si3 211/S i32 12
Register 1. PCM Mode Select Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PCME R/W
PCMF[1:0] R/W
PCMT R/W
GCI R/W
TRI R/W
Reset settings = 0000_1000
Bit Name Function
7:6 5
Reserved PCME
Read returns zero.
PCM Enable. 0 = Disable PCM transfers. 1 = Enable PCM transfers. PCM Format. 00 = A-Law 01 = -Law 10 = Reserved 11 = Linear PCM Transfer Size. 0 = 8-bit transfer. 1 = 16-bit transfer. GCI Clock Format. 0 = 1 PCLK per data bit. 1 = 2 PCLKs per data bit. Tri-state Bit 0. 0 = Tri-state bit 0 on positive edge of PCLK. 1 = Tri-state bit 0 on negative edge of PCLK.
4:3
PCMF[1:0]
2
PCMT
1
GCI
0
TRI
Register 2. PCM Transmit Start Count--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
TXS[7:0] R/W
Reset settings = 0000_0000
Bit Name Function PCM Transmit Start Count. PCM transmit start count equals the number of PCLKs following FSYNC before data transmission begins. See Figure 27 on page 46.
7:0
TXS[7:0]
56
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 3. PCM Transmit Start Count--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
TXS[9:8] R/W
Reset settings = 0000_0000
Bit Name Function
7:2 1:0
Reserved TXS[9:8]
Read returns zero.
PCM Transmit Start Count. PCM transmit start count equals the number of PCLKs following FSYNC before data transmission begins. See Figure 27 on page 46.
Register 4. PCM Receive Start Count--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RXS[7:0] R/W
Reset settings = 0000_0000
Bit Name Function PCM Receive Start Count. PCM receive start count equals the number of PCLKs following FSYNC before data reception begins. See Figure 27 on page 46.
7:0
RXS[7:0]
Register 5. PCM Receive Start Count--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RXS[9:8] R/W
Reset settings = 0000_0000
Bit Name Function
7:2 1:0
Reserved RXS[9:8]
Read returns zero.
PCM Receive Start Count. PCM receive start count equals the number of PCLKs following FSYNC before data reception begins. See Figure 27 on page 46.
Preliminary Rev. 1.11
57
Si 3210/ Si3 211/S i32 12
Register 6. Digital Input/Output Control SI3210 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
Reset settings = 0000_0000
Si3211/Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
DOUT R/W
DIO2 R/W
DIO1 R/W
PD2 R/W
PD1 R/W
Reset settings = 0000_0000
Bit Name Function
7:5 4
Reserved DOUT
Read returns zero.
DOUT Pin Output Data (Si3211/Si3212 only). 0 = DOUT pin driven low. 1 = DOUT pin driven high. SI3210 = Reserved. DIO2 Pin Input/Output Direction. 0 = DIO2 pin is an input. 1 = DIO2 pin is an output and driven to value of the PD2 bit. SI3210 = Reserved. DIO1 Pin Input/Output Direction. 0 = DIO1 pin is an input. 1 = DIO1 pin is an output and driven to value of the PD1 bit. SI3210 = Reserved. DIO2 Pin Data. When DIO2 = 1: 0 = DIO2 pin driven low. 1 = DIO2 pin driven high. SI3210 = Reserved. When DIO2 = 0, PD2 value equals the logic input of DIO2 pin. DIO1 Pin Data. When DIO1 = 1: 0 = DIO1 pin driven low. 1 = DIO1 pin driven high. SI3210 = Reserved. When DIO1 = 0, PD1 value equals the logic input of DIO1 pin.
3
DIO2
2
DIO1
1
PD2
0
PD1
58
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 8. Audio Path Loopback Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
ALM2 R/W
DLM R/W
ALM1 R/W
Reset settings = 0000_0010
Bit Name Function
7:3 2
Reserved ALM2
Read returns zero.
Analog Loopback Mode 2. (See Figure 23 on page 40.) 0 = Full analog loopback mode disabled. 1 = Full analog loopback mode enabled. Digital Loopback Mode. (See Figure 23 on page 40.) 0 = Digital loopback disabled. 1 = Digital loopback enabled. Analog Loopback Mode 1. (See Figure 23 on page 40.) 0 = Analog loopback disabled. 1 = Analog loopback enabled.
1
DLM
0
ALM1
Preliminary Rev. 1.11
59
Si 3210/ Si3 211/S i32 12
Register 9. Audio Gain Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RXHP R/W
TXHP R/W
TXM R/W
RXM R/W
ATX[1:0] R/W
ARX[1:0] R/W
Reset settings = 0000_0000
Bit Name Function Receive Path High Pass Filter Disable. 0 = HPF enabled in receive path, RHDF. 1 = HPF bypassed in receive path, RHDF. Transmit Path High Pass Filter Disable. 0 = HPF enabled in transmit path, THPF. 1 = HPF bypassed in transmit path, THPF. Transmit Path Mute. Refer to position of digital mute in Figure 23 on page 40. 0 = Transmit signal passed. 1 = Transmit signal muted. Receive Path Mute. Refer to position of digital mute in Figure 23 on page 40. 0 = Receive signal passed. 1 = Receive signal muted. Analog Transmit Path Gain. 00 = 0 dB 01 = -3.5 dB 10 = 3.5 dB 11 = ATX gain = 0 dB; analog transmit path muted. Analog Receive Path Gain. 00 = 0 dB 01 = -3.5 dB 10 = 3.5 dB 11 = Analog receive path muted.
7
RXHP
6
TXHP
5
TXM
4
RXM
3:2
ATX[1:0]
1:0
ARX[1:0]
60
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 10. Two-Wire Impedance Synthesis Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
CLC[1:0] R/W
TISE R/W
TISS[2:0] R/W
Reset settings = 0000_1000
Bit Name Function
7:6 5:4
Reserved CLC[1:0]
Read returns zero.
Line Capacitance Compensation. 00 = Off 01 = 4.7 nF 10 = 10 nF 11 = Reserved Two-Wire Impedance Synthesis Enable. 0 = Two-wire impedance synthesis disabled. 1 = Two-wire impedance synthesis enabled. Two-Wire Impedance Synthesis Selection. 000 = 600 001 = 900 010 = 600 + 2.16 F 011 = 900 + 2.16 F 100 = CTR21 (270 + 750 || 150 nF) 101 = Australia/New Zealand #1 (220 + 820 || 120 nF) 110 = Slovakia/Slovenia/South Africa (220 + 820 || 115 nF) 111 = New Zealand #2 (370 + 620 || 310 nF)
3
TISE
2:0
TISS[2:0]
Preliminary Rev. 1.11
61
Si 3210/ Si3 211/S i32 12
Register 11. Hybrid Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
HYBP[2:0] R/W
HYBA[2:0] R/W
Reset settings = 0011_0011
Bit Name Function
7 6:4
Reserved HYBP[2:0]
Read returns zero.
Pulse Metering Hybrid Adjustment. 000 = 4.08 dB 001 = 2.5 dB 010 = 1.16 dB 011 = 0 dB 100 = -1.02 dB 101 = -1.94 dB 110 = -2.77 dB 111 = Off
3 2:0
Reserved HYBA[2:0]
Read returns zero.
Audio Hybrid Adjustment. 000 = 4.08 dB 001 = 2.5 dB 010 = 1.16 dB 011 = 0 dB 100 = -1.02 dB 101 = -1.94 dB 110 = -2.77 dB 111 = Off
62
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 14. Power Down Control 1 SI3210 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PMON R/W
DCOF R/W
MOF R/W
BIASOF R/W
SLICOF R/W
Reset settings = 0001_0000
Si3211/Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PMON R/W
MOF R/W
BIASOF R/W
SLICOF R/W
Reset settings = 0001_0000
Bit Name Function
7:6 5
Reserved PMON
Read returns zero.
Pulse Metering DAC Power-On Control. 0 = Automatic power control. 1 = Override automatic control and force pulse metering DAC circuitry on. DC-DC Converter Power-Off Control (SI3210 only). 0 = Automatic power control. 1 = Override automatic control and force dc-dc circuitry off. Si3211/Si3212 = Read returns 1; it cannot be written. Monitor ADC Power-Off Control. 0 = Automatic power control. 1 = Override automatic control and force monitor ADC circuitry off.
4
DCOF
3
MOF
2 1
Reserved BIASOF
Read returns zero.
DC Bias Power-Off Control. 0 = Automatic power control. 1 = Override automatic control and force dc bias circuitry off. SLIC Power-Off Control. 0 = Automatic power control. 1 = Override automatic control and force SLIC circuitry off.
0
SLICOF
Preliminary Rev. 1.11
63
Si 3210/ Si3 211/S i32 12
Register 15. Power Down Control 2 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
ADCM R/W
ADCON R/W
DACM R/W
DACON R/W
GMM R/W
GMON R/W
Reset settings = 0000_0000
Bit Name Function
7:6 5
Reserved ADCM
Read returns zero.
Analog to Digital Converter Manual/Automatic Power Control. 0 = Automatic power control. 1 = Manual power control; ADCON controls on/off state. Analog to Digital Converter On/Off Power Control. When ADCM = 1: 0 = Analog to digital converter powered off. 1 = Analog to digital converter powered on. ADCON has no effect when ADCM = 0. Digital to Analog Converter Manual/Automatic Power Control. 0 = Automatic power control. 1 = Manual power control; DACON controls on/off state. Digital to Analog Converter On/Off Power Control. When DACM = 1: 0 = Digital to analog converter powered off. 1 = Digital to analog converter powered on. DACON has no effect when DACM = 0. Transconductance Amplifier Manual/Automatic Power Control. 0 = Automatic power control. 1 = Manual power control; GMON controls on/off state. Transconductance Amplifier On/Off Power Control. When GMM = 1: 0 = Analog to digital converter powered off. 1 = Analog to digital converter powered on. GMON has no effect when GMM = 0.
4
ADCON
3
DACM
2
DACON
1
GMM
0
GMON
64
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 18. Interrupt Status 1 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PMIP R/W
PMAP R/W
RGIP R/W
RGAP R/W
O2IP R/W
O2AP R/W
O1IP R/W
O1AP R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Inactive Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Pulse Metering Active Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Ringing Inactive Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Ringing Active Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Oscillator 2 Inactive Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Oscillator 2 Active Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Oscillator 1 Inactive Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Oscillator 1 Active Timer Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending.
7
PMIP
6
PMAP
5
RGIP
4
RGAP
3
O2IP
2
O2AP
1
O1IP
0
O1AP
Preliminary Rev. 1.11
65
Si 3210/ Si3 211/S i32 12
Register 19. Interrupt Status 2 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
Q6AP R/W
Q5AP R/W
Q4AP R/W
Q3AP R/W
Q2AP R/W
Q1AP R/W
LCIP R/W
RTIP R/W
Reset settings = 0000_0000
Bit Name Function Power Alarm Q6 Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Power Alarm Q5 Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Power Alarm Q4 Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Power Alarm Q3 Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Power Alarm Q2 Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Power Alarm Q1 Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Loop Closure Transition Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Ring Trip Interrupt Pending. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending.
7
Q6AP
6
Q5AP
5
Q4AP
4
Q3AP
3
Q2AP
2
Q1AP
1
LCIP
0
RTIP
66
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 20. Interrupt Status 3 SI3210/Si3211 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
CMCP R/W
INDP R/W
DTMFP R/W
Reset settings = 0000_0000
Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
CMCP R/W
INDP R/W
Reset settings = 0000_0000
Bit Name Function
7:3 2
Reserved CMCP
Read returns zero.
Common Mode Calibration Error Interrupt. This bit is set when off-hook/on-hook status changes during the common mode balance calibration. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Indirect Register Access Serviced Interrupt. This bit is set once a pending indirect register service request has been completed. Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. DTMF Tone Detected Interrupt (SI3210 and Si3211 only). Writing 1 to this bit clears a pending interrupt. 0 = No interrupt pending. 1 = Interrupt pending. Si3212 = Reserved; read returns 0.
1
INDP
0
DTMFP
Preliminary Rev. 1.11
67
Si 3210/ Si3 211/S i32 12
Register 21. Interrupt Enable 1 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PMIE R/W
PMAE R/W
RGIE R/W
RGAE R/W
O2IE R/W
O2AE R/W
O1IE R/W
O1AE R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Inactive Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Pulse Metering Active Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Ringing Inactive Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Ringing Active Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Oscillator 2 Inactive Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Oscillator 2 Active Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Oscillator 1 Inactive Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Oscillator 1 Active Timer Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled.
7
PMIE
6
PMAE
5
RGIE
4
RGAE
3
O2IE
2
O2AE
1
O1IE
0
O1AE
68
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 22. Interrupt Enable 2 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
Q6AE R/W
Q5AE R/W
Q4AE R/W
Q3AE R/W
Q2AE R/W
Q1AE R/W
LCIE R/W
RTIE R/W
Reset settings = 0000_0000
Bit Name Function Power Alarm Q6 Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Power Alarm Q5 Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Power Alarm Q4 Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Power Alarm Q3 Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Power Alarm Q2 Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Power Alarm Q1 Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Loop Closure Transition Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Ring Trip Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled.
7
Q6AE
6
Q5AE
5
Q4AE
4
Q3AE
3
Q2AE
2
Q1AE
1
LCIE
0
RTIE
Preliminary Rev. 1.11
69
Si 3210/ Si3 211/S i32 12
Register 23. Interrupt Enable 3 SI3210/Si3211 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
CMCE R/W
INDE R/W
DTMFE R/W
Reset settings = 0000_0000
Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
CMCE R/W
INDE R/W
Reset settings = 0000_0000
Bit Name Function
7:3 2
Reserved CMCE
Read returns zero.
Common Mode Calibration Error Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. Indirect Register Access Serviced Interrupt Enable. 0 = Interrupt masked. 1 = Interrupt enabled. DTMF Tone Detected Interrupt Enable (SI3210 and Si3211 only). 0 = Interrupt masked. 1 = Interrupt enabled. Si3212 = Reserved.
1
INDE
0
DTMFE
70
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 24. DTMF Decode Status SI3210/Si3211 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VAL R
DIG[3:0] R
Reset settings = 0000_0000
Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
Reset settings = 0000_0000
Bit Name Function
7:5 4
Reserved VAL
Read returns zero.
DTMF Valid Digit Decoded. 0 = Not currently detecting digit. 1 = Currently detecting digit. Si3212 = Reserved; read returns 0. DTMF Digit (SI3210 and Si3211 only). 0001 = "1" 0010 = "2" 0011 = "3" 0100 = "4" 0101 = "5" 0110 = "6" 0111 = "7" 1000 = "8" 1001 = "9" 1010 = "0" 1011 = "*" 1100 = "#" 1101 = "A" 1110 = "B" 1111 = "C" 0000 = "D" Si3212 = Reserved; read returns 0.
3:0
DIG[3:0]
Preliminary Rev. 1.11
71
Si 3210/ Si3 211/S i32 12
Register 28. Indirect Data Access--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IDA[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Indirect Data Access--Low Byte. A write to IDA followed by a write to IAA will place the contents of IDA into an indirect register at the location referenced by IAA at the next indirect register update (16 kHz update rate--a write operation). Writing IAA only will load IDA with the value stored at IAA at the next indirect memory update (a read operation).
7:0
IDA[7:0]
Register 29. Indirect Data Access--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IDA[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Indirect Data Access--High Byte. A write to IDA followed by a write to IAA will place the contents of IDA into an indirect register at the location referenced by IAA at the next indirect register update (16 kHz update rate--a write operation). Writing IAA only will load IDA with the value stored at IAA at the next indirect memory update (a read operation).
7:0
IDA[15:8]
72
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 30. Indirect Address Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IAA[7:0] R/W
Reset settings = xxxx_xxxx
Bit Name Function Indirect Address Access. A write to IDA followed by a write to IAA will place the contents of IDA into an indirect register at the location referenced by IAA at the next indirect register update (16 kHz update rate--a write operation). Writing IAA only will load IDA with the value stored at IAA at the next indirect memory update (a read operation).
7:0
IAA[7:0]
Register 31. Indirect Address Status Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IAS R
Reset settings = 0000_0000
Bit Name Function
7:1 0
Reserved IAS
Read returns zero.
Indirect Access Status. 0 = No indirect memory access pending. 1 = Indirect memory access pending.
Preliminary Rev. 1.11
73
Si 3210/ Si3 211/S i32 12
Register 32. Oscillator 1 Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OSS1 R
REL R/W
OZ1 R/W
O1TAE R/W
O1TIE R/W
O1E R/W
O1SO[1:0] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 1 Signal Status. 0 = Output signal inactive. 1 = Output signal active. Oscillator 1 Automatic Register Reload. This bit should be set for FSK signaling. 0 = Oscillator 1 will stop signaling after inactive timer expires. 1 = Oscillator 1 will continue to read register parameters and output signals. Oscillator 1 Zero Cross Enable. 0 = Signal terminates after active timer expires. 1 = Signal terminates at zero crossing after active timer expires. Oscillator 1 Active Timer Enable. 0 = Disable timer. 1 = Enable timer. Oscillator 1 Inactive Timer Enable. 0 = Disable timer. 1 = Enable timer. Oscillator 1 Enable. 0 = Disable oscillator. 1 = Enable oscillator. Oscillator 1 Signal Output Routing. 00 = Unassigned path (output not connected). 01 = Assign to transmit path. 10 = Assign to receive path. 11 = Assign to both paths.
7
OSS1
6
REL
5
OZ1
4
O1TAE
3
O1TIE
2
O1E
1:0
O1SO[1:0]
74
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 33. Oscillator 2 Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OSS2 R
OZ2 R/W
O2TAE R/W
O2TIE R/W
O2E R/W
O2SO[1:0] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 2 Signal Status. 0 = Output signal inactive. 1 = Output signal active.
7
OSS2
6 5
Reserved OZ2
Read returns zero.
Oscillator 2 Zero Cross Enable. 0 = Signal terminates after active timer expires. 1 = Signal terminates at zero crossing. Oscillator 2 Active Timer Enable. 0 = Disable timer. 1 = Enable timer. Oscillator 2 Inactive Timer Enable. 0 = Disable timer. 1 = Enable timer. Oscillator 2 Enable. 0 = Disable oscillator. 1 = Enable oscillator. Oscillator 2 Signal Output Routing. 00 = Unassigned path (output not connected) 01 = Assign to transmit path. 10 = Assign to receive path. 11 = Assign to both paths.
4
O2TAE
3
O2TIE
2
O2E
1:0
O2SO[1:0]
Preliminary Rev. 1.11
75
Si 3210/ Si3 211/S i32 12
Register 34. Ringing Oscillator Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RSS R
RDAC R
RTAE R/W
RTIE R/W
ROE R
RVO R/W
TSWS R/W
Reset settings = 0000_0000
Bit Name Function Ringing Signal Status. 0 = Ringing oscillator output signal inactive. 1 = Ringing oscillator output signal active.
7
RSS
6 5
Reserved RDAC
Read returns zero.
Ringing Signal DAC/Linefeed Cross Indicator. For ringing signal start and stop, output to TIP and RING is suspended to ensure continuity with dc linefeed voltages. RDAC indicates that ringing signal is actually present at TIP and RING. 0 = Ringing signal not present at TIP and RING. 1 = Ringing signal present at TIP and RING. Ringing Active Timer Enable. 0 = Disable timer. 1 = Enable timer. Ringing Inactive Timer Enable. 0 = Disable timer. 1 = Enable timer. Ringing Oscillator Enable. 0 = Ringing oscillator disabled. 1 = Ringing oscillator enabled. Ringing Voltage Offset. 0 = No dc offset added to ringing signal. 1 = DC offset added to ringing signal. Trapezoid/Sinusoid Waveshape Select. 0 = Sinusoid 1 = Trapezoid
4
RTAE
3
RTIE
2
ROE
1
RVO
0
TSWS
76
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 35. Pulse Metering Oscillator Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PSTAT R
PMAE R/W
PMIE R/W
PMOE R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Signal Status. 0 = Output signal inactive. 1 = Output signal active.
7
PSTAT
6:5 4
Reserved PMAE
Read returns zero.
Pulse Metering Active Timer Enable. 0 = Disable timer. 1 = Enable timer. Pulse Metering Inactive Timer Enable. 0 = Disable timer. 1 = Enable timer. Pulse Metering Oscillator Enable. 0 = Disable oscillator. 1 = Enable oscillator.
3
PMIE
2
PMOE
1:0
Reserved
Read returns zero.
Preliminary Rev. 1.11
77
Si 3210/ Si3 211/S i32 12
Register 36. Oscillator 1 Active Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OAT1[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 1 Active Timer. LSB = 125 s
7:0
OAT1[7:0]
Register 37. Oscillator 1 Active Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OAT1[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 1 Active Timer.
7:0
OAT1[15:8]
Register 38. Oscillator 1 Inactive Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OIT1[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 1 Inactive Timer. LSB = 125 s
7:0
OIT1[7:0]
78
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 39. Oscillator 1 Inactive Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OIT1[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 1 Inactive Timer.
7:0
OIT1[15:8]
Register 40. Oscillator 2 Active Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OAT2[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 2 Active Timer. LSB = 125 s
7:0
OAT2[7:0]
Register 41. Oscillator 2 Active Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OAT2[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 2 Active Timer.
7:0
OAT2[15:8]
Preliminary Rev. 1.11
79
Si 3210/ Si3 211/S i32 12
Register 42. Oscillator 2 Inactive Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OIT2[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 2 Inactive Timer. LSB = 125 s
7:0
OIT2[7:0]
Register 43. Oscillator 2 Inactive Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
OIT2[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Oscillator 2 Inactive Timer.
7:0
OIT2[15:8]
Register 44. Pulse Metering Oscillator Active Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PAT[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Active Timer. LSB = 125 s
7:0
PAT[7:0]
80
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 45. Pulse Metering Oscillator Active Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PAT[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Active Timer.
7:0
PAT[15:8]
Register 46. Pulse Metering Oscillator Inactive Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PIT[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Inactive Timer. LSB = 125 s
7:0
PIT[7:0]
Register 47. Pulse Metering Oscillator Inactive Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PIT[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Pulse Metering Inactive Timer.
7:0
PIT[15:8]
Preliminary Rev. 1.11
81
Si 3210/ Si3 211/S i32 12
Register 48. Ringing Oscillator Active Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RAT[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Ringing Active Timer. LSB = 125 s
7:0
RAT[7:0]
Register 49. Ringing Oscillator Active Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RAT[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Ringing Active Timer.
7:0
RAT[15:8]
Register 50. Ringing Oscillator Inactive Timer--Low Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RIT[7:0] R/W
Reset settings = 0000_0000
Bit Name Function Ringing Inactive Timer. LSB = 125 s
7:0
RIT[7:0]
82
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 51. Ringing Oscillator Inactive Timer--High Byte Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RIT[15:8] R/W
Reset settings = 0000_0000
Bit Name Function Ringing Inactive Timer.
7:0
RIT[15:8]
Register 52. FSK Data Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
FSKDAT R/W
Reset settings = 0000_0000
Bit Name Function
7:1 0
Reserved FSKDAT
Read returns zero.
FSK Data. When FSKEN = 1 (direct Register 108, bit 6) and REL = 1 (direct Register 32, bit 6), this bit serves as the buffered input for FSK generation bit stream data.
Register 63. Loop Closure Debounce Interval Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
LCD[7:0]
Reset settings = 0011_0010 (revision C); 0101_0100 (subsequent revisions)
Bit Name Function Loop Closure Debounce Interval for Automatic Ringing. This register sets the loop closure debounce interval for the ringing silent period when using automatic ringing cadences. The value may be set between 0 ms (0x00) and 159 ms (0x7F) in 1.25 ms steps.
7:0
LCD[7:0]
Preliminary Rev. 1.11
83
Si 3210/ Si3 211/S i32 12
Register 64. Linefeed Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
LFS[2:0] R
LF[2:0] R/W
Reset settings = 0000_0000
Bit Name Function
7 6:4
Reserved LFS[2:0]
Read returns zero.
Linefeed Shadow. This register reflects the actual realtime linefeed state. Automatic operations may cause actual linefeed state to deviate from the state defined by linefeed register (e.g., when linefeed equals ringing state, LFS will equal on-hook transmission state during ringing silent period and ringing state during ring burst). 000 = Open 001 = Forward active 010 = Forward on-hook transmission 011 = TIP open 100 = Ringing 101 = Reverse active 110 = Reverse on-hook transmission 111 = RING open
3 2:0
Reserved LF[2:0]
Read returns zero.
Linefeed. Writing to this register sets the linefeed state. 000 = Open 001 = Forward active 010 = Forward on-hook transmission 011 = TIP open 100 = Ringing 101 = Reverse active 110 = Reverse on-hook transmission 111 = RING open
84
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 65. External Bipolar Transistor Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
SQH R/W
CBY R/W
ETBE R/W
ETBO[1:0] R/W
ETBA[1:0] R/W
Reset settings = 0110_0001
Bit Name Function
7 6
Reserved SQH
Read returns zero.
Audio Squelch. 0 = No squelch. 1 = STIPAC and SRINGAC pins squelched. Capacitor Bypass. 0 = Capacitors CP (C1) and CM (C2) in circuit. 1 = Capacitors CP (C1) and CM (C2) bypassed. External Transistor Bias Enable. 0 = Bias disabled. 1 = Bias enabled. External Transistor Bias Levels--On-Hook Transmission State. DC bias current which flows through external BJTs in the on-hook transmission state. Increasing this value increases the compliance of the ac longitudinal balance circuit. 00 = 4 mA 01 = 8 mA 10 = 12 mA 11 = Reserved External Transistor Bias Levels--Active Off-Hook State. DC bias current which flows through external BJTs in the active off-hook state. Increasing this value increases the compliance of the ac longitudinal balance circuit. 00 = 4 mA 01 = 8 mA 10 = 12 mA 11 = Reserved
5
CBY
4
ETBE
3:2
ETBO[1:0]
1:0
ETBA[1:0]
Preliminary Rev. 1.11
85
Si 3210/ Si3 211/S i32 12
Register 66. Battery Feed Control SI3210 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VOV R/W
FVBAT R/W
TRACK R/W
Reset settings = 0000_0011
Si3211/Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
BATSL R/W
Reset settings = 0000_0110
Bit Name Function
7:5 4
Reserved VOV
Read returns zero.
Overhead Voltage Range Increase. (SI3210 only; See Figure 17 on page 29.) This bit selects the programmable range for VOV, which is defined in indirect Register 41. 0 = VOV = 0 V to 9 V 1 = VOV = 0 V to 13.5 V Si3211/Si3212 = Reserved. VBAT Manual Setting (SI3210 only).
3
FVBAT
0 = Normal operation 1 = VBAT tracks VBATH register. Si3211/Si3212 = Read returns 0; it cannot be written. 2 1 Reserved BATSL SI3210 = Read returns zero. Si3211/Si3212 = Read returns one.
Battery Feed Select (Si3211/Si3212 only). This bit selects between high and low battery supplies. 0 = Low battery selected (DCSW pin low). 1 = High battery selected (DCSW pin high). SI3210 = Read returns zero. DC-DC Converter Tracking Mode (SI3210 only). 0 = |VBAT| will not decrease below VBATL. 1 = VBAT tracks VRING. Si3211/Si3212 = Reserved.
0
TRACK
86
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 67. Automatic/Manual Control Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
MNCM R/W
MNDIF R/W
SPDS R/W
ABAT R/W
AORD R/W
AOLD R/W
AOPN R/W
Reset settings = 0001_1111
Bit Name Function
7 6
Reserved MNCM
Read returns zero.
Common Mode Manual/Automatic Select. 0 = Automatic control. 1 = Manual control, in which TIP (forward) or RING (reverse) forces voltage to follow VCM value. Differential Mode Manual/Automatic Select. 0 = Automatic control. 1 = Manual control (forces differential voltage to follow VOC value). Speed-Up Mode Enable. 0 = Speed-up disabled. 1 = Automatic speed-up. Battery Feed Automatic/Manual Select. 0 = Automatic mode disabled. 1 = Automatic mode enabled (automatic switching to low battery in off-hook state). Automatic/Manual Ring Trip Detect. 0 = Manual mode. 1 = Enter off-hook active state automatically upon ring trip detect. Automatic/Manual Loop Closure Detect. 0 = Manual mode. 1 = Enter off-hook active state automatically upon loop closure detect. Power Alarm Automatic/Manual Detect. 0 = Manual mode. 1 = Enter open state automatically upon power alarm.
5
MNDIF
4
SPDS
3
ABAT
2
AORD
1
AOLD
0
AOPN
Preliminary Rev. 1.11
87
Si 3210/ Si3 211/S i32 12
Register 68. Loop Closure/Ring Trip Detect Status Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
DBIRAW R
RTP R
LCR R
Reset settings = 0000_0000
Bit Name Function
7:3 2
Reserved DBIRAW
Read returns zero.
Ring Trip/Loop Closure Unfiltered Output. State of this bit reflects the realtime output of ring trip and loop closure detect circuits before debouncing. 0 = Ring trip/loop closure threshold exceeded. 1 = Ring trip/loop closure threshold not exceeded. Ring Trip Detect Indicator (Filtered Output). 0 = Ring trip detect has not occurred. 1 = Ring trip detect occurred. Loop Closure Detect Indicator (Filtered Output). 0 = Loop closure detect has not occurred. 1 = Loop closure detect has occurred.
1
RTP
0
LCR
Register 69. Loop Closure Debounce Interval Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
LCDI[6:0] R/W
Reset settings = 0000_1010
Bit Name Function
7 6:0
Reserved LCDI[6:0]
Read returns zero.
Loop Closure Debounce Interval. The value written to this register defines the minimum steady state debounce time. Value may be set between 0 ms (0x00) to 159 ms (0x7F) in 1.25 ms steps. Default value = 12.5 ms.
88
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 70. Ring Trip Detect Debounce Interval Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
RTDI[6:0] R/W
Reset settings = 0000_1010
Bit Name Function
7 6:0
Reserved RTDI[6:0]
Read returns zero.
Ring Trip Detect Debounce Interval. The value written to this register defines the minimum steady state debounce time. The value may be set between 0 ms (0x00) to 159 ms (0x7F) in 1.25 ms steps. Default value = 12.5 ms.
Register 71. Loop Current Limit Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
ILIM[2:0] R/W
Reset settings = 0000_0000
Bit Name Function
7:3 2:0
Reserved ILIM[2:0]
Read returns zero.
Loop Current Limit. The value written to this register sets the constant loop current. The value may be set between 20 mA (0x00) and 41 mA (0x07) in 3 mA steps.
Preliminary Rev. 1.11
89
Si 3210/ Si3 211/S i32 12
Register 72. On-Hook Line Voltage Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VSGN R/W
VOC[5:0] R/W
Reset settings = 0010_0000
Bit Name Function
7 6
Reserved VSGN
Read returns zero.
On-Hook Line Voltage. The value written to this bit sets the on-hook line voltage polarity (VTIP-VRING). 0 = VTIP-VRINGis positive 1 = VTIP-VRING is negative On-Hook Line Voltage. The value written to this register sets the on-hook line voltage (VTIP-VRING). Value may be set between 0 V (0x00) and 94.5 V (0x3F) in 1.5 V steps. Default value = 48 V.
5:0
VOC[5:0]
Register 73. Common Mode Voltage Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VCM[5:0] R/W
Reset settings = 0000_0010
Bit Name Function
7:6 5:0
Reserved VCM[5:0]
Read returns zero.
Common Mode Voltage. The value written to this register sets VTIP for forward active and forward on-hook transmission states and VRING for reverse active and reverse on-hook transmission states. The value may be set between 0 V (0x00) and -94.5 V (0x3F) in 1.5 V steps. Default value = -3 V.
90
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 74. High Battery Voltage Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VBATH[5:0] R/W
Reset settings = 0011_0010
Bit Name Function
7:6 5:0
Reserved VBATH[5:0]
Read returns zero.
High Battery Voltage. The value written to this register sets high battery voltage. VBATH must be greater than or equal to VBATL. The value may be set between 0 V (0x00) and -94.5 V (0x3F) in 1.5 V steps. Default value = -75 V. For Si3211 and Si3212, VBATH must be set equal to externally supplied VBATH input voltage.
Register 75. Low Battery Voltage Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VBATL[5:0] R/W
Reset settings = 0001_0000
Bit Name Function
7:6 5:0
Reserved VBATL[5:0]
Read returns zero.
Low Battery Voltage. The value written to this register sets low battery voltage. VBATH must be greater than or equal to VBATL. The value may be set between 0 V (0x00) and -94.5 V (0x3F) in 1.5 V steps. Default value = -24 V. For Si3211 and Si3212, VBATL must be set equal to externally supplied VBATL input voltage.
Preliminary Rev. 1.11
91
Si 3210/ Si3 211/S i32 12
Register 76. Power Monitor Pointer Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PWRMP[2:0] R/W
Reset settings = 0000_0000
Bit Name Function
7:3 2:0
Reserved PWRMP[2:0]
Read returns zero.
Power Monitor Pointer. Selects the external transistor from which to read power output. The power of the selected transistor is read in the PWROM register. 000 = Q1 001 = Q2 010 = Q3 011 = Q4 100 = Q5 101 = Q6 110 = Undefined 111 = Undefined
Register 77. Line Power Output Monitor Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
PWROM[7:0] R
Reset settings = 0000_0000
Bit Name Function Line Power Output Monitor. This register reports the realtime power output of the transistor selected using PWRMP. The range is 0 W (0x00) to 7.8 W (0xFF) in 30.4 mW steps for Q1, Q2, Q5, and Q6. The range is 0 W (0x00) to 0.9 W (0xFF) in 3.62 mW steps for Q3 and Q4.
7:0
PWROM[7:0]
92
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 78. Loop Voltage Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
LVSP R
LVS[5:0] R
Reset settings = 0000_0000
Bit Name Function
7 6
Reserved LVSP
Read returns zero.
Loop Voltage Sense Polarity. This register reports the polarity of the differential loop voltage (VTIP - VRING). 0 = Positive loop voltage (VTIP > VRING). 1 = Negative loop voltage (VTIP < VRING). Loop Voltage Sense Magnitude. This register reports the magnitude of the differential loop voltage (VTIP-VRING). The range is 0 V to 94.5 V in 1.5 V steps.
5:0
LVS[5:0]
Register 79. Loop Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
LCSP R
LCS[5:0] R
Reset settings = 0000_0000
Bit Name Function
7 6
Reserved LCSP
Read returns zero.
Loop Current Sense Polarity. This register reports the polarity of the loop current. 0 = Positive loop current (forward direction). 1 = Negative loop current (reverse direction). Loop Current Sense Magnitude. This register reports the magnitude of the loop current. The range is 0 mA to 80 mA in 1.27 mA steps.
5:0
LCS[5:0]
Preliminary Rev. 1.11
93
Si 3210/ Si3 211/S i32 12
Register 80. TIP Voltage Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VTIP[7:0] R
Reset settings = 0000_0000
Bit Name Function TIP Voltage Sense. This register reports the realtime voltage at TIP with respect to ground. The range is 0 V (0x00) to -95.88 V (0xFF) in .376 V steps.
7:0
VTIP[7:0]
Register 81. RING Voltage Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VRING[7:0] R
Reset settings = 0000_0000
Bit Name Function RING Voltage Sense. This register reports the realtime voltage at RING with respect to ground. The range is 0 V (0x00) to -95.88 V (0xFF) in .376 V steps.
7:0
VRING[7:0]
Register 82. Battery Voltage Sense 1 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VBATS1[7:0] R
Reset settings = 0000_0000
Bit Name Function Battery Voltage Sense 1. This register is one of two registers that reports the realtime voltage at VBAT with respect to ground. The range is 0 V (0x00) to -95.88 V (0xFF) in .376 V steps.
7:0
VBATS1[7:0]
94
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 83. Battery Voltage Sense 2 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
VBATS2[7:0] R
Reset settings = 0000_0000
Bit Name Function Battery Voltage Sense 2. This register is one of two registers that reports the realtime voltage at VBAT with respect to ground. The range is 0 V (0x00) to -95.88 V (0xFF) in .376 V steps.
7:0
VBATS2[7:0]
Register 84. Transistor 1 Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IQ1[7:0] R
Reset settings = xxxx_xxxx
Bit Name Function Transistor 1 Current Sense. This register reports the realtime current through Q1. The range is 0 A (0x00) to 81.35 mA (0xFF) in .319 mA steps. If ETBE = 1, the reported value does not include the additional ETBO/A current.
7:0
IQ1[7:0]
Register 85. Transistor 2 Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IQ2[7:0] R
Reset settings = xxxx_xxxx
Bit Name Function Transistor 2 Current Sense. This register reports the realtime current through Q2. The range is 0 A (0x00) to 81.35 mA (0xFF) in .319 mA steps. If ETBE = 1, the reported value does not include the additional ETBO/A current.
7:0
IQ2[7:0]
Preliminary Rev. 1.11
95
Si 3210/ Si3 211/S i32 12
Register 86. Transistor 3 Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IQ3[7:0] R
Reset settings = xxxx_xxxx
Bit Name Function Transistor 3 Current Sense. This register reports the realtime current through Q3. The range is 0 A (0x00) to 9.59 mA (0xFF) in 37.6 A steps.
7:0
IQ3[7:0]
Register 87. Transistor 4 Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IQ4[7:0] R
Reset settings = xxxx_xxxx
Bit Name Function Transistor 4 Current Sense. This register reports the realtime current through Q4. The range is 0 A (0x00) to 9.59 mA (0xFF) in 37.6 A steps.
7:0
IQ4[7:0]
Register 88. Transistor 5 Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IQ5[7:0] R
Reset settings = xxxx_xxxx
Bit Name Function Transistor 5 Current Sense. This register reports the realtime current through Q5. The range is 0 A (0x00) to 80.58 mA (0xFF) in .316 mA steps.
7:0
IQ5[7:0]
96
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 89. Transistor 6 Current Sense Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
IQ6[7:0] R
Reset settings = xxxx_xxxx
Bit Name Function Transistor 6 Current Sense. This register reports the realtime current through Q6. The range is 0 A (0x00) to 80.58 mA (0xFF) in .316 mA steps.
7:0
IQ6[7:0]
Register 92. DC-DC Converter PWM Period SI3210 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
DCN[7] R/W
1 R
DCN[5:0] R/W
Reset settings = 1111_1111
Si3211/Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
Reset settings = xxxx_xxxx
Bit Name Function DC-DC Converter Period. This bit sets the PWM period for the dc-dc converter. The range is 3.906 s (0x40) to 15.564 s (0xFF) in 61.035 ns steps. Si3211/Si3212 = Reserved. Bit 6 is fixed to one and read-only, so there are two ranges of operation: 3.906 s-7.751 s, used for MOSFET transistor switching. 11.719 s-15.564 s, used for BJT transistor switching.
7:0
DCN[7:0]
Preliminary Rev. 1.11
97
Si 3210/ Si3 211/S i32 12
Register 93. DC-DC Converter Switching Delay SI3210 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
DCCAL R/W
DCPOL R
DCTOF[4:0] R/W
Reset settings = 0001_0100 (SI3210) Reset settings = 0011_0100 (SI3210M)
Si3211/Si3212 Bit Name Type D7 D6 D5 D4 D3 D2 D1 D0
Reset settings = xxxx_xxxx
Bit Name Function DC-DC Converter Peak Current Monitor Calibration Status (SI3210 only). Writing a one to this bit starts the dc-dc converter peak current monitor calibration routine. 0 = Normal operation. 1 = Calibration being performed. Si3211/Si3212 = Reserved.
7
DCCAL
6 5
Reserved DCPOL
Read returns zero.
DC-DC Converter Feed Forward Pin (DCFF) Polarity (SI3210 only). This read-only register bit indicates the polarity relationship of the DCFF pin to the DCDRV pin. Two versions of the SI3210 are offered to support the two relationships. 0 = DCFF pin polarity is opposite of DCDRV pin (SI3210). 1 = DCFF pin polarity is same as DCDRV pin (SI3210M). Si3211/Si3212 = Reserved. DC-DC Converter Minimum Off Time (SI3210 only). This register sets the minimum off time for the pulse width modulated dc-dc converter control. TOFF = (DCTOF + 4) 61.035 ns. Si3211/Si3212 = Reserved.
4:0
DCTOF[4:0]
98
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 94. DC-DC Converter PWM Pulse Width SI3210 Bit Name Type Reset settings = 0000_0000 Si3211/Si3212 Bit Name Type Reset settings = 0000_0000 Bit 7:0 Name DCPW[7:0] Function DC-DC Converter Pulse Width (SI3210 only). Pulse width of DCDRV is given by PW = (DCPW - DCTOF - 4) 61.035 ns. Si3211/Si3212 = Reserved. D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
DCPW[7:0] R
Preliminary Rev. 1.11
99
Si 3210/ Si3 211/S i32 12
Register 96. Calibration Control/Status Register 1 Bit Name Type D7 D6 CAL R/W D5 CALSP R/W D4 CALR R/W D3 CALT R/W D2 CALD R/W D1 CALC R/W D0 CALIL R/W
Reset settings = 0001_1111 Bit 7 6 Name Reserved CAL Read returns zero. Calibration Control/Status Bit. Setting this bit begins calibration of the entire system. 0 = Normal operation or calibration complete. 1 = Calibration in progress. Calibration Speedup. Setting this bit shortens the time allotted for VBAT settling at the beginning of the calibration cycle. 0 = 300 ms 1 = 30 ms RING Gain Mismatch Calibration. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. TIP Gain Mismatch Calibration. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. Differential DAC Gain Calibration. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. Common Mode DAC Gain Calibration. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. ILIM Calibration. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. Function
5
CALSP
4
CALR
3
CALT
2
CALD
1
CALC
0
CALIL
100
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 97. Calibration Control/Status Register 2 Bit Name Type Reset settings = 0001_1111 Bit 7:5 4 Name Reserved CALM1 Read returns zero. Monitor ADC Calibration 1. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. Monitor ADC Calibration 2. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. DAC Calibration. Setting this bit begins calibration of the audio DAC offset. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. ADC Calibration. Setting this bit begins calibration of the audio ADC offset. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. Common Mode Balance Calibration. Setting this bit begins calibration of the ac longitudinal balance. 0 = Normal operation or calibration complete. 1 = Calibration enabled or in progress. Function D7 D6 D5 D4 CALM1 R/W D3 CALM2 R/W D2 CALDAC R/W D1 CALADC R/W D0 CALCM R/W
3
CALM2
2
CALDAC
1
CALADC
0
CALCM
Preliminary Rev. 1.11
101
Si 3210/ Si3 211/S i32 12
Register 98. RING Gain Mismatch Calibration Result Bit Name Type Reset settings = 0001_0000 Bit 7:5 4:0 Name Reserved CALGMR[4:0] Read returns zero. Gain Mismatch of IE Tracking Loop for RING Current. Function D7 D6 D5 D4 D3 D2 CALGMR[4:0] R/W D1 D0
Register 99. TIP Gain Mismatch Calibration Result Bit Name Type Reset settings = 0001_0000 Bit 7:5 4:0 Name Reserved CALGMT[4:0] Read returns zero. Gain Mismatch of IE Tracking Loop for TIP Current. Function D7 D6 D5 D4 D3 D2 CALGMT[4:0] R/W D1 D0
Register 100. Differential Loop Current Gain Calibration Result Bit Name Type Reset settings = 0001_0001 Bit 7:5 4:0 Name Reserved CALGD[4:0] Read returns zero. Differential DAC Gain Calibration Result. Function D7 D6 D5 D4 D3 D2 CALGD[4:0] R/W D1 D0
102
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 101. Common Mode Loop Current Gain Calibration Result Bit Name Type Reset settings = 0001_0001 Bit 7:5 4:0 Name Reserved CALGC[4:0] Read returns zero. Common Mode DAC Gain Calibration Result. Function D7 D6 D5 D4 D3 D2 CALGC[4:0] R/W D1 D0
Register 102. Current Limit Calibration Result Bit Name Type Reset settings = 0000_1000 Bit 7:5 3:0 Name Reserved CALGIL[3:0] Read returns zero. Current Limit Calibration Result. Function D7 D6 D5 D4 D3 D2 D1 D0
CALGIL[3:0] R/W
Register 103. Monitor ADC Offset Calibration Result Bit Name Type Reset settings = 1000_1000 Bit 7:4 3:0 Name CALMG1[3:0] CALMG2[3:0] Function Monitor ADC Offset Calibration Result 1. Monitor ADC Offset Calibration Result 2. D7 D6 D5 D4 D3 D2 D1 D0
CALMG1[3:0] R/W
CALMG2[3:0] R/W
Preliminary Rev. 1.11
103
Si 3210/ Si3 211/S i32 12
Register 104. Analog DAC/ADC Offset Bit Name Type Reset settings = 0000_0000 Bit 7:4 3 2 1 0 Name Reserved DACP DACN ADCP ADCN Read returns zero. Positive Analog DAC Offset. Negative Analog DAC Offset. Positive Analog ADC Offset. Negative Analog ADC Offset. Function D7 D6 D5 D4 D3 DACP R/W D2 DACN R/W D1 ADCP R/W D0 ADCN R/W
Register 105. DAC Offset Calibration Result Bit Name Type Reset settings = 0000_0000 Bit 7:0 Name DACOF[7:0] DAC Offset Calibration Result. Function D7 D6 D5 D4 D3 D2 D1 D0
DACOF[7:0] R/W
Register 106. Common Mode Calibration Result Bit Name Type Reset settings = 0010_0000 Bit 7:6 5:0 Name Reserved CMBAL[5:0] Read returns zero. Common Mode Calibration Result. Function D7 D6 D5 D4 D3 D2 D1 D0
CMBAL[5:0]
104
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Register 107. DC Peak Current Monitor Calibration Result Bit Name Type Reset settings = 0000_1000 Bit 7:4 3:0 Name Reserved CMDCPK[3:0] Read returns zero. DC Peak Current Monitor Calibration Result. Function D7 D6 D5 D4 D3 D2 D1 D0
CMDCPK[3:0] R/W
Preliminary Rev. 1.11
105
Si 3210/ Si3 211/S i32 12
Register 108. Enhancement Enable
Note: The Enhancement Enable register and associated features are available in silicon revisions C and later.
SI3210 Bit Name Type D7 ILIMEN R/W D6 FSKEN R/W D5 DCSU R/W D4 ZSEXT R/W D3 D2 LCVE R/W D1 DCFIL R/W D0 HYSTEN R/W
Reset settings = 0000_0000 Si3211/Si3212 Bit Name Type D7 ILIMEN R/W D6 FSKEN R/W D5 D4 ZSEXT R/W D3 SWDB R/W D2 LCVE R/W D1 D0 HYSTEN R/W
Reset settings = 0000_0000 Bit 7 Name ILIMEN Function Current Limit Increase. When enabled, this bit temporarily increases the maximum differential current limit at the end of a ring burst to enable a faster settling time to a dc linefeed state. 0 = The value programmed in ILIM (direct Register 71) is used. 1 = The maximum differential loop current limit is temporarily increased to 41 mA. FSK Generation Enhancement. When enabled, this bit will increase the clocking rate of tone generator 1 to 24 kHz only when the REL bit (direct Register 32, bit 6) is set. Also, dedicated oscillator registers are used for FSK generation (indirect registers 99-104). Audio tones are generated using this new higher frequency, and oscillator 1 active and inactive timers have a finer bit resolution of 41.67 s. This provides greater resolution during FSK caller ID signal generation. 0 = Tone generator always clocked at 8 kHz; OSC1, OSC1X., and OSC1Y are always used. 1 = Tone generator module clocked at 24 kHz and dedicated FSK registers used only when REL = 1; otherwise clocked at 8 kHz. DC-DC Converter Control Speedup (SI3210 only). When enabled, this bit invokes a multi-threshold error control algorithm which allows the dc-dc converter to adjust more quickly to voltage changes. 0 = Normal control algorithm used. 1 = Multi-threshold error control algorithm used.
6
FSKEN
5
DCSU
106
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Bit 4 Name ZSEXT Function Impedance Internal Reference Resistor Disable. When enabled, this bit removes the internal reference resistor used to synthesize ac impedances for 600 + 2.1 F and 900 + 2.16 F so that an external resistor reference may be used. 0 = Internal resistor used to generate 600 + 2.1 F and 900 + 2.16 F impedances. 1 = Internal resistor removed from circuit. Battery Switch Debounce (Si3211 and Si3212 only). When enabled, this bit allows debouncing of the battery switching circuit only when transitioning from VBATH to VBATL external battery supplies (EXTBAT = 1). 0 = No debounce used. 1 = 60 ms debounce period used. SI3210 = Reserved. Voltage-Based Loop Closure. Enables loop closure to be determined by the TIP-to-RING voltage rather than loop current. 0 = Loop closure determined by loop current. 1 = Loop closure determined by TIP-to-RING voltage. DC-DC Converter Squelch (SI3210 only). When enabled, this bit squelches noise in the audio band from the dc-dc converter control loop. 0 = Voice band squelch disabled. 1 = Voice band squelch enabled. Loop Closure Hysteresis Enable. When enabled, this bit allows hysteresis to the loop closure calculation. The upper and lower hysteresis thresholds are defined by indirect registers 28 and 43, respectively. 0 = Loop closure hysteresis disabled. 1 = Loop closure hysteresis enabled.
3
SWDB
2
LCVE
1
DCFIL
0
HYSTEN
Preliminary Rev. 1.11
107
Si 3210/ Si3 211/S i32 12
Indirect Registers
Indirect registers are not directly mapped into memory but are accessible through the IDA and IAA registers. A write to IDA followed by a write to IAA is interpreted as a write request to an indirect register. In this case, the contents of IDA are written to indirect memory at the location referenced by IAA at the next indirect register update. A write to IAA without first writing to IDA is interpreted as a read request from an indirect register. In this case, the value located at IAA is written to IDA at the next indirect register update. Indirect registers are updated at a rate of 16 kHz. For pending indirect register transfers, IAS (direct Register 31) will be one until serviced. In addition an interrupt, IND (Register 20), can be generated upon completion of the indirect transfer.
DTMF Decoding (SI3210 and Si3211 only)
All values are represented in twos-complement format.
Note: The values of all indirect registers are undefined following the reset state.
Table 35. DTMF Indirect Registers Summary
Addr. D15 0 1 2 3 4 5 6 7 8 9 10 11 12 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
ROW0[15:0] ROW1[15:0] ROW2[15:0] ROW3[15:0] COL[15:0] FWDTW[15:0] REVTW[15:0] ROWREL[15:0] COLREL[15:0] ROW2[15:0] COL2[15:0] PWRMIN[15:0] HOTL[15:0]
Table 36. DTMF Indirect Registers Description
Addr. 0 Description DTMF Row 0 Peak Magnitude Pass Ratio Threshold. This register sets the minimum power ratio threshold for row 0 DTMF detection. If the ratio of power in row 0 to total power in the row band is greater than ROW0, then a row 0 signal is detected. A value of 0x7FF0 corresponds to a 1.0 ratio. DTMF Row 1 Peak Magnitude Pass Ratio Threshold. This register sets the minimum power ratio threshold for row 1 DTMF detection. If the ratio of power in row 1 to total power in the row band is greater than ROW1, then a row 1 signal is detected. A value of 0x7FF0 corresponds to a 1.0 ratio. Reference Page 38
1
38
108
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 36. DTMF Indirect Registers Description (Continued)
Addr. 2 Description DTMF Row 2 Peak Magnitude Pass Ratio Threshold. This register sets the minimum power ratio threshold for row 2 DTMF detection. If the ratio of power in row 2 to total power in the row band is greater than ROW2, then a row 2 signal is detected. A value of 0x7FF0 corresponds to a 1.0 ratio. DTMF Row 3 Peak Magnitude Pass Ratio Threshold. This register sets the minimum power ratio threshold for row 3 DTMF detection. If the ratio of power in row 3 to total power in the row band is greater than ROW3, then a row 3 signal is detected. A value of 0x7FF0 corresponds to a 1.0 ratio. DTMF Column Peak Magnitude Pass Threshold. This register sets the minimum power ratio threshold for column DTMF detection; all columns use the same threshold. If the ratio of power in a particular column to total power in the column band is greater than COL, then a column detect for that particular column signal is detected. A value of 0x7FF0 corresponds to a 1.0 ratio. DTMF Forward Twist Threshold. This register sets the threshold for the power ratio of row power to column power. A value of 0x7F0 corresponds to a 1.0 ratio. DTMF Reverse Twist Threshold. This register sets the threshold for the power ratio of column power to row power. A value of 0x7F0 corresponds to a 1.0 ratio. DTMF Row Ratio Threshold. This register sets the threshold for the power ratio of highest power row to the other rows. A value of 0x7F0 corresponds to a 1.0 ratio. DTMF Column Ratio Threshold. This register sets the threshold for the power ratio of highest power column to the other columns. A value of 0x7F0 corresponds to a 1.0 ratio. DTMF Row Second Harmonic Threshold. This register sets the threshold for the power ratio of peak row tone to its second harmonic. A value of 0x7F0 corresponds to a 1.0 ratio. DTMF Column Second Harmonic Threshold. This register sets the threshold for the power ratio of peak column tone to its second harmonic. A value of 0x7F0 corresponds to a 1.0 ratio. DTMF Power Minimum Threshold. This register sets the threshold for the minimum total power in the DTMF calculation, under which the calculation is ignored. DTMF Hot Limit Threshold. This register sets the two-step AGC in the DTMF path. Reference Page 38
3
38
4
38
5
38
6
38
7
38
8
38
9
38
10
38
11
38
12
38
Preliminary Rev. 1.11
109
Si 3210/ Si3 211/S i32 12
Oscillators
See functional description sections of tone generation, ringing, and pulse metering for guidelines on computing register values. All values are represented in twos-complement format.
Note: The values of all indirect registers are undefined following the reset state. Shaded areas denote bits that can be read and written but should be written to zeroes.
Table 37. Oscillator Indirect Registers Summary
Addr. D15 13 14 15 16 17 18 19 20 21 22 23 24 25 ROFF[5:0] RCO[15:0] RNGX[15:0] RNGY[15:0] PLSD[15:0] PLSX[15:0] PLSCO[15:0] D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
OSC1[15:0] OSC1X[15:0] OSC1Y[15:0] OSC2[15:0] OSC2X[15:0] OSC2Y[15:0]
Table 38. Oscillator Indirect Registers Description
Addr. 13 14 15 16 17 18 19 Oscillator 1 Frequency Coefficient. Sets tone generator 1 frequency. Oscillator 1 Amplitude Register. Sets tone generator 1 signal amplitude. Oscillator 1 Initial Phase Register. Sets initial phase of tone generator 1 signal. Oscillator 2 Frequency Coefficient. Sets tone generator 2 frequency. Oscillator 2 Amplitude Register. Sets tone generator 2 signal amplitude. Oscillator 2 Initial Phase Register. Sets initial phase of tone generator 2 signal. Ringing Oscillator DC Offset. Sets dc offset component (VTIP-VRING) to ringing waveform. The range is 0 to 94.5 V in 1.5 V increments. Description Reference Page 31 31 31 31 31 31 33
110
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 38. Oscillator Indirect Registers Description (Continued)
Addr. 20 21 22 23 24 25 Description Ringing Oscillator Frequency Coefficient. Sets ringing generator frequency. Ringing Oscillator Amplitude Register. Sets ringing generator signal amplitude. Ringing Oscillator Initial Phase Register. Sets initial phase of ringing generator signal. Pulse Metering Oscillator Attack/Decay Ramp Rate. Sets pulse metering attack/decay ramp rate. Pulse Metering Oscillator Amplitude Register. Sets pulse metering generator signal amplitude. Pulse Metering Oscillator Frequency Coefficient. Sets pulse metering generator frequency. Reference Page 33 33 33 37 37 37
Digital Programmable Gain/Attenuation
See functional description sections of digital programmable gain/attenuation for guidelines on computing register values. All values are represented in twos-complement format.
Note: The values of all indirect registers are undefined following the reset state. Shaded areas denote bits that can be read and written but should be written to zeroes.
Table 39. Digital Programmable Gain/Attenuation Indirect Registers Summary
Addr. D15 26 27 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
DACG[11:0] ADCG[11:0]
Table 40. Digital Programmable Gain/Attenuation Indirect Registers Description
Addr. 26 Description Receive Path Digital to Analog Converter Gain/Attenuation. This register sets gain/attenuation for the receive path. The digitized signal is effectively multiplied by DACG to achieve gain/attenuation. A value of 0x00 corresponds to - dB gain (mute). A value of 0x400 corresponds to unity gain. A value of 0x7FF corresponds to a gain of 6 dB. Transmit Path Analog to Digital Converter Gain/Attenuation. This register sets gain/attenuation for the transmit path. The digitized signal is effectively multiplied by ADCG to achieve gain/attenuation. A value of 0x00 corresponds to - dB gain (mute). A value of 0x400 corresponds to unity gain. A value of 0x7FF corresponds to a gain of 6 dB. Reference Page 39
27
39
Preliminary Rev. 1.11
111
Si 3210/ Si3 211/S i32 12
SLIC Control
See descriptions of linefeed interface and power monitoring for guidelines on computing register values. All values are represented in twos-complement format.
Note: The values of all indirect registers are undefined following the reset state. Shaded areas denote bits that can be read and written but should be written to zeroes.
Table 41. SLIC Control Indirect Registers Summary
Addr. D15 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
*Note: SI3210 only.
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
LCRT[5:0] RPTP[5:0] CML[5:0] CMH[5:0] PPT12[7:0] PPT34[7:0] PPT56[7:0] NCLR[12:0] NRTP[12:0] NQ12[12:0] NQ34[12:0] NQ56[12:0] VCMR[3:0] VMIND[3:0]*
LCRTL[5:0]
Table 42. SLIC Control Indirect Registers Description
Addr. 28 Description Loop Closure Threshold. Loop closure detection threshold. This register defines the upper bounds threshold if hysteresis is enabled (direct Register 108, bit 0). The range is 0-80 mA in 1.27 mA steps. Ring Trip Threshold. Ring trip detection threshold during ringing. Common Mode Minimum Threshold for Speed-Up. This register defines the negative common mode voltage threshold. Exceeding this threshold enables a wider bandwidth of dc linefeed control for faster settling times. The range is 0-23.625 V in 0.375 V steps. Common Mode Maximum Threshold for Speed-Up. This register defines the positive common mode voltage threshold. Exceeding this threshold enables a wider bandwidth of dc linefeed control for faster settling times. The range is 0-23.625 V in 0.375 V steps. Reference Page 26
29 30
36
31
112
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Table 42. SLIC Control Indirect Registers Description (Continued)
Addr. 32 33 34 35 36 37 38 39 40 41 Description Power Alarm Threshold for Transistors Q1 and Q2. Power Alarm Threshold for Transistors Q3 and Q4. Power Alarm Threshold for Transistors Q5 and Q6. Loop Closure Filter Coefficient. Ring Trip Filter Coefficient. Thermal Low Pass Filter Pole for Transistors Q1 and Q2. Thermal Low Pass Filter Pole for Transistors Q3 and Q4. Thermal Low Pass Filter Pole for Transistors Q5 and Q6. Common Mode Bias Adjust During Ringing. Recommended value of 6 decimal. DC-DC Converter VOV Voltage (SI3210 only). This register sets the overhead voltage, VOV, to be supplied by the dc-dc converter. When the VOV bit = 0 (direct Register 66, bit 4), VOV should be set between 0 and 9 V (VMIND = 0 to 6h). When the VOV bit = 1, VOV should be set between 0 and 13.5 V (VMIND = 0 to 9h). Reserved. Loop Closure Threshold--Lower Bound. This register defines the lower threshold for loop closure hysteresis, which is enabled in bit 0 of direct Register 108. The range is 0-80 mA in 1.27 mA steps. 26 Reference Page 24 24 24 26 36 24 24 24 33 27
42 43
FSK Control
For detailed instructions on FSK signal generation, refer to "Application Note 32: FSK Generation" (AN32). These registers support enhanced FSK generation mode, which is enabled by setting FSKEN = 1 (direct Register 108, bit 6) and REL = 1 (direct Register 32, bit 6).
Table 43. FSK Control Indirect Registers Summary
Addr. D15 99 100 101 102 103 104 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
FSK0X[15:0] FSK0[15:0] FSK1X[15:0] FSK1[15:0] FSK01[15:0] FSK10[15:0]
Preliminary Rev. 1.11
113
Si 3210/ Si3 211/S i32 12
Table 44. FSK Control Indirect Registers Description
Addr. 99 Description FSK Amplitude Coefficient for Space. When FSKEN = 1 and REL = 1, this register sets the amplitude to be used when generating a space or "0". When the active timer (OAT1) expires, the value of this register is loaded into oscillator 1 instead of OSC1X. FSK Frequency Coefficient for Space. When FSKEN = 1 and REL = 1, this register sets the frequency to be used when generating a space or "0". When the active timer (OAT1) expires, the value of this register is loaded into oscillator 1 instead of OSC1. FSK Amplitude Coefficient for Mark. When FSKEN = 1 and REL = 1, this register sets the amplitude to be used when generating a mark or "1". When the active timer (OAT1) expires, the value of this register is loaded into oscillator 1 instead of OSC1X. FSK Frequency Coefficient for Mark. When FSKEN = 1 and REL = 1, this register sets the frequency to be used when generating a mark or "1". When the active timer (OAT1) expires, the value of this register is loaded into oscillator 1 instead of OSC1. FSK Transition Parameter from 0 to 1. When FSKEN = 1 and REL = 1, this register defines a gain correction factor that is applied to signal amplitude when transitioning from a space (0) to a mark (1). FSK Transition Parameter from 1 to 0. When FSKEN = 1 and REL = 1, this register defines a gain correction factor that is applied to signal amplitude when transitioning from a mark (1) to a space (0). Reference Page 33 and AN32
100
33 and AN32
101
33 and AN32
102
33 and AN32
103
33 and AN32
104
33 and AN32
114
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Pin Descriptions: SI3210/11/12
CS INT PCLK DRX DTX FSYNC RESET SDCH/DIO1 SDCL/DIO2 VDDA1 IREF CAPP QGND CAPM STIPDC SRINGDC STIPE SVBAT SRINGE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20
SCLK SDI SDO SDITHRU
DCDRV/DCSW
DCFF/DOUT TEST GNDD VDDD ITIPN ITIPP VDDA2 IRINGP IRINGN IGMP GNDA IGMN SRINGAC STIPAC
Pin # 1
Pin Name CS
Description Chip Select. Active low. When inactive, SCLK and SDI are ignored and SDO is high impedance. When active, the serial port is operational. Interrupt. Maskable interrupt output. Open drain output for wire-ORed operation. PCM Bus Clock. Clock input for PCM bus timing. Receive PCM Data. Input data from PCM bus. Transmit PCM Data. Output data to PCM bus. Frame Synch. 8 kHz frame synchronization signal for the PCM bus. May be short or long pulse format. Reset. Active low input. Hardware reset used to place all control registers in the default state. DC Monitor/General Purpose I/O. DC-DC converter monitor input used to detect overcurrent situations in the converter (SI3210 only). General purpose I/O (Si3211/Si3212 only).
2 3 4 5 6 7 8
INT PCLK DRX DTX FSYNC RESET SDCH/DIO1
9
SDCL/DIO2
DC Monitor/General Purpose I/O. DC-DC converter monitor input used to detect overcurrent situations in the converter (SI3210 only). General purpose I/O (Si3211/Si3212 only).
Preliminary Rev. 1.11
115
Si 3210/ Si3 211/S i32 12
Pin # 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Pin Name VDDA1 IREF CAPP QGND CAPM STIPDC SRINGDC STIPE SVBAT SRINGE STIPAC SRINGAC IGMN GNDA IGMP IRINGN IRINGP VDDA2 ITIPP ITIPN Analog Supply Voltage. Analog power supply for internal analog circuitry. Current Reference. Connects to an external resistor used to provide a high accuracy reference current. SLIC Stabilization Capacitor. Capacitor used in low pass filter to stabilize SLIC feedback loops. Component Reference Ground. SLIC Stabilization Capacitor. Capacitor used in low pass filter to stabilize SLIC feedback loops. TIP Sense. Analog current input used to sense voltage on the TIP lead. RING Sense. Analog current input used to sense voltage on the RING lead. TIP Emitter Sense. Analog current input used to sense voltage on the Q6 emitter lead. VBAT Sense. Analog current input used to sense voltage on dc-dc converter output voltage lead. RING Emitter Sense. Analog current input used to sense voltage on the Q5 emitter lead. TIP Transmit Input. Analog ac input used to detect voltage on the TIP lead. RING Transmit Input. Analog ac input used to detect voltage on the RING lead. Transconductance Amplifier External Resistor. Negative connection for transconductance gain setting resistor. Analog Ground. Ground connection for internal analog circuitry. Transconductance Amplifier External Resistor. Positive connection for transconductance gain setting resistor. Negative Ring Current Control. Analog current output driving Q3. Positive Ring Current Control. Analog current output driving Q2. Analog Supply Voltage. Analog power supply for internal analog circuitry. Positive TIP Current Control. Analog current output driving Q1. Negative TIP Current Control. Analog current output driving Q4. Description
116
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Pin # 30 31 32 Pin Name VDDD GNDD TEST Digital Supply Voltage. Digital power supply for internal digital circuitry. Digital Ground. Ground connection for internal digital circuitry. Test. Enables test modes for Silicon Labs internal testing. This pin should always be tied to ground for normal operation. 33 DCFF/DOUT DC Feed-Forward/High Current General Purpose Output. Feed-forward drive of external bipolar transistors to improve dc-dc converter efficiency (SI3210 only). High current output pin (Si3211/Si3212 only). 34 DCDRV/DCSW DC Drive/Battery Switch. DC-DC converter control signal output which drives external bipolar transistor (SI3210 only). Battery switch control signal output which drives external bipolar transistor (Si3211/Si3212 only). 35 36 37 38 SDITHRU SDO SDI SCLK SDI Passthrough. Cascaded SDI output signal for daisy-chain mode. Serial Port Data Out. Serial port control data output. Serial Port Data In. Serial port control data input. Serial Port Bit Clock Input. Serial port clock input. Controls the serial data on SDO and latches the data on SDI. Description
Preliminary Rev. 1.11
117
Si 3210/ Si3 211/S i32 12
Ordering Guide
Table 45. Ordering Guide
Chip SI3210-KT SI3210-BT SI3210M-KT SI3210M-BT Si3211-KT Si3211-BT Si3212-KT Si3212-BT Description ProSLIC ProSLIC ProSLIC ProSLIC ProSLIC ProSLIC ProSLIC ProSLIC DC-DC Converter DTMF Decoder DCFF Pin Output = DCDRV = DCDRV = DCDRV = DCDRV n/a n/a n/a n/a Package TSSOP-38 TSSOP-38 TSSOP-38 TSSOP-38 TSSOP-38 TSSOP-38 TSSOP-38 TSSOP-38 Temperature 0C to 70C -40C to 85C 0C to 70C -40C to 85C 0C to 70C -40C to 85C 0C to 70C -40C to 85C
118
Preliminary Rev. 1.11
SI3210/Si3211/Si3212
Package Outline: 38-Pin TSSOP
Figure 31 illustrates the package details for the Si321x. Table 46 lists the values for the dimensions shown in the illustration.
E
H L
B D A e C
A1
Figure 31. 38-pin Thin Shrink Small Outline Package (TSSOP) Table 46. Package Diagram Dimensions
Inches Symbol A A1 B C D E e H L Min -- 0.002 0.007 0.004 Max 0.047 0.006 0.011 0.008 Millimeters Min -- 0.05 0.17 0.09 Max 1.1 0.15 0.27 0.20
0.381 BSC 0.169 0.177
9.7 BSC 4.30 .5 BSC 6.40 BSC 0.45 0 0.75 8 4.50
.02 BSC 0.252 BSC 0.018 0 0.030 8
Preliminary Rev. 1.11
119
Si 3210/ Si3 211/S i32 12
Document Changes from Revision 0.9 to Revision 1.0
General Change Summary Updates to describe revision E silicon Added SI3210M device and description Modified current application schematics and component lists Added MOSFET/transformer application schematic and component list Added optional equivalent Q5, Q6 bias circuit Updated register descriptions relating to current, voltage, and power measurement, and to revision E modifications List of Document Changes Figure 9: SI3210 Typical Application Circuit Using BJT/Inductor DC-DC Converter: Updated Table 12: SI3210 External Component Values--BJT/ Inductor: Updated Figure 10: SI3210M Typical Application Circuit Using MOSFET/Transformer DC-DC Converter: Added Table 13: SI3210M External Component Values-- BMOSFET/Transformer: Added Figure 11: Si3211/12 Typical Application Circuit Using External Battery: Updated Table 14: Si3211/12 External Component Values-- External Battery: Updated Figure 12: Si321x Optional Equivalent Q5, Q6 Bias Circuit: Added Table 15: Si321x Optional Bias Component Values: Added Section: Power Monitoring and Fault Line Detection: power calculation example updated Table 17: Associated Power Monitoring and Power Fault Registers: updated Section: Battery Voltage Generation and Switching: Updated Section: Linefeed Considerations During Ringing: Corrected equation for VOVR Table 18: Measured Realtime Linefeed Interface Characteristics: Updated Table 19: Associated Power Monitoring and Power Fault Registers: Updated Table 21: SI3210 and SI3210M Differences: Added Register 0: PN updated Register 14: PLLOF removed Register 66: EXTBAT removed Register 77: PWROM updated Registers 80-89: Updated
120
Register 92: DCN updated Register 93: DCPOL updated Table 33: Oscillator Indirect Registers Summary: Updated Indirect Register 30: CML updated Indirect Register 31: CMH updated Pin Descriptions: Updated Table 40: Ordering Guide: Updated
Document Changes from Revision 1.0 to Revision 1.1
Modified current application schematics and components lists Indirect Register 28: Updated Indirect Register 43: Updated Section: Serial Peripheral Interface: Updated
Preliminary Rev. 1.11
SI3210/Si3211/Si3212 NOTES:
Preliminary Rev. 1.11
121
Si 3210/ Si3 211/S i32 12
Contact Information
Silicon Laboratories Inc. 4635 Boston Lane Austin, TX 78735 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Email: productinfo@silabs.com Internet: www.silabs.com
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories, Silicon Labs, and ProSLIC are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
122
Preliminary Rev. 1.11


▲Up To Search▲   

 
Price & Availability of SI3210

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X