Part Number Hot Search : 
X9514WSI HT074007 FR510F T6P22 MRF275G RF830 FM250 00390
Product Description
Full Text Search
 

To Download S83C751-5A28 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 INTEGRATED CIRCUITS
83C751/87C751 80C51 8-bit microcontroller family
2K/64 OTP/ROM, I2C, low pin count
Product specification Supersedes data of 1998 Jan 19 IC20 Data Handbook 1998 May 01
Philips Semiconductors
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
DESCRIPTION
The Philips 83C751/87C751 offers the advantages of the 80C51 architecture in a small package and at low cost. The 8XC751 Microcontroller is fabricated with Philips high-density CMOS technology. Philips epitaxial substrate minimizes CMOS latch-up sensitivity. The 8XC751 contains a 2k x 8 ROM (83C751) EPROM (87C751), a 64 x 8 RAM, 19 I/O lines, a 16-bit auto-reload counter/timer, a five-source, fixed-priority level interrupt structure, a bidirectional inter-integrated circuit (I2C) serial bus interface, and an on-chip oscillator. The on-board inter-integrated circuit (I2C) bus interface allows the 8XC751 to operate as a master or slave device on the I2C small area network. This capability facilitates I/O and RAM expansion, access to EEPROM, processor-to-processor communication, and efficient interface to a wide variety of dedicated I2C peripherals.
PIN CONFIGURATIONS
P3.4/A4 1 P3.3/A3 2 P3.2/A2/A10 3 P3.1/A1/A9 4 P3.0/A0/A8 5 P0.2/VPP 6 P0.1/SDA/OE-PGM 7 P0.0/SCL/ASEL RST 8 9 PLASTIC DUAL IN-LINE PACKAGE AND SHRINK SMALL OUTLINE PACKAGE 24 VCC 23 P3.5/A5 22 P3.6/A6 21 P3.7/A7 20 P1.7/T0/D7 19 P1.6/INT1/D6 18 P1.5/INT0/D5 17 P1.4/D4 16 P1.3/D3 15 P1.2/D2 14 P1.1/D1 13 P1.0/D0
X2 10 X1 11 VSS 12
FEATURES
* 80C51 based architecture * Inter-Integrated Circuit (I2C) serial bus interface * Small package sizes
- 24-pin DIP (300 mil "skinny DIP") - 24-pin Shrink Small Outline Package - 28-pin PLCC
4 5
1
26 25
PLASTIC LEADED CHIP CARRIER 11 12 Pin 1 2 3 4 5 6 7 8 9 Function P3.4/A4 P3.3/A3 P3.2/A2/A10 P3.1/A1/A9 NC* P3.0/A0/A8 P0.2/VPP P0.1/SDA/OE-PGM P0.0//SCLASEL 18 Pin 19 20 21 22 23 24 25 26 27 28 Function P1.4/D4 P1.5/INT0/D5 NC* NC* P1.6/INT1/D6 P1.7/T0/D7 P3.7/A7 P3.6/A6 P3.5/A5 VCC 19
* 87C751 available in one-time programmable plastic packages * Wide oscillator frequency range * Low power consumption:
- Normal operation: less than 11mA @ 5V, 12MHz - Idle mode - Power-down mode
PinFunction 10 NC* 11 RST 12 X2 13 X1 14 VSS 15 P1.0/D0 16 P1.1/D1 17 P1.2/D2 18 P1.3/D3
* 2k x 8 ROM (83C751)
* DO NOT CONNECT
2k x 8 EPROM (87C751)
SU00315
* 64 x 8 RAM * 16-bit auto reloadable counter/timer * Fixed-rate timer * Boolean processor * CMOS and TTL compatible * Well suited for logic replacement, consumer and industrial
applications
* LED drive outputs
1998 May 01
2
853-0599 19326
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
ORDERING INFORMATION
ROM S83C751-1N24 S83C751-2N24 S83C751-4N24 S83C751-5N24 S83C751-1A28 S83C751-2A28 S83C751-4A28 S83C751-5A28 S83C751-1DB S83C751-4DB EPROM1 S87C751-1N24 S87C751-2N24 S87C751-4N24 S87C751-5N24 S87C751-1A28 S87C751-2A28 S87C751-4A28 S87C751-5A28 S87C751-1DB S87C751-4DB OTP OTP OTP OTP OTP OTP OTP OTP OTP OTP TEMPERATURE RANGE C AND PACKAGE 0 to +70, Plastic Dual In-line Package -40 to +85, Plastic Dual In-line Package 0 to +70, Plastic Dual In-line Package -40 to +85, Plastic Dual In-line Package 0 to +70, Plastic Leaded Chip Carrier -40 to +85, Plastic Leaded Chip Carrier 0 to +70, Plastic Leaded Chip Carrier -40 to +85, Plastic Leaded Chip Carrier 0 to +70, Shrink Small Outline Package 0 to +70, Shrink Small Outline Package FREQUENCY 3.5 to 12MHz 3.5 to 12MHz 3.5 to 16MHz 3.5 to 16MHz 3.5 to 12MHz 3.5 to 12MHz 3.5 to 16MHz 3.5 to 16MHz 3.5 to 12MHz 3.5 to 16MHz DRAWING NUMBER SOT222-1 SOT222-1 SOT222-1 SOT222-1 SOT261-3 SOT261-3 SOT261-3 SOT261-3 SOT340-1 SOT340-1
NOTE: 1. OTP = One Time Programmable EPROM.
1998 May 01
3
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
BLOCK DIAGRAM
P0.0-P0.2
PORT 0 DRIVERS VCC VSS RAM ADDR REGISTER RAM PORT 0 LATCH ROM/ EPROM I2C CONTROL
B REGISTER
ACC
STACK POINTER PROGRAM ADDRESS REGISTER
TMP2
TMP1
ALU
PCON I2DAT
I2CFG I2STA I2CON TH0 RTH IE TL0 RTL
TCON
BUFFER
PSW
INTERRUPT, SERIAL PORT AND TIMER BLOCKS
PC INCREMENTER
PROGRAM COUNTER INSTRUCTION REGISTER
RST
TIMING AND CONTROL
DPTR
PD
PORT 1 LATCH
PORT 3 LATCH
OSCILLATOR PORT 1 DRIVERS X1 X2 P1.0-P1.7 P3.0-P3.7 PORT 3 DRIVERS
SU00316
1998 May 01
4
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
PIN DESCRIPTIONS
PIN NO. MNEMONIC VSS VCC P0.0-P0.2 DIP/ SSOP 12 24 8-6 LCC 14 28 9-7 TYPE I I I/O Circuit Ground Potential Supply voltage during normal, idle, and power-down operation. Port 0: Port 0 is a 3-bit open-drain, bidirectional port. Port 0 pins that have 1s written to them float, and in that state can be used as high-impedance inputs. Port 0 also serves as the serial I2C interface. When this feature is activated by software, SCL and SDA are driven low in accordance with the I2C protocol. These pins are driven low if the port register bit is written with a 0 or if the I2C subsystem presents a 0. The state of the pin can always be read from the port register by the program. To comply with the I2C specification, P0.0 and P0.1 are open drain bidirectional I/O pins with the electrical characteristics listed in the tables that follow. While these differ from "standard TTL" characteristics, they are close enough for the pins to still be used as general-purpose I/O in non-I2C applications. Port 0 also provides alternate functions for programming the EPROM memory as follows: VPP (P0.2) - Programming voltage input. (See Note 1.) OE/PGM (P0.1) - Input which specifies verify mode (output enable) or the program mode. OE/PGM = 1 output enabled (verify mode). OE/PGM = 0 program mode. ASEL (P0.0) - Input which indicates which bits of the EPROM address are applied to port 3. ASEL = 0 low address byte available on port 3. ASEL = 1 high address byte available on port 3 (only the three least significant bits are used). SDA (P0.1) - I2C data. SCL (P0.0) - I2C clock. Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Port 1 serves to output the addressed EPROM contents in the verify mode and accepts as inputs the value to program into the selected address during the program mode. Port 1 also serves the special function features of the 80C51 family as listed below: INT0 (P1.5): External interrupt. INT1 (P1.6): External interrupt. T0 (P1.7): Timer 0 external input. Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: IIL). Port 3 also functions as the address input for the EPROM memory location to be programmed (or verified). The 11-bit address is multiplexed into this port as specified by P0.0/ASEL. Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device. An internal diffused resistor to VSS permits a power-on RESET using only an external capacitor to VCC. After the device is reset, a 10-bit serial sequence, sent LSB first, applied to RESET, places the device in the programming state allowing programming address, data and VPP to be applied for programming or verification purposes. The RESET serial sequence must be synchronized with the X1 input. Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. X1 also serves as the clock to strobe in a serial bit stream into RESET to place the device in the programming state. Crystal 2: Output from the inverting oscillator amplifier. NAME AND FUNCTION
6 7
7 8
N/A I
8
9
I
7 8 P1.0-P1.7 13-20
8 9 15-20, 23, 24
I/O I/O I/O
18 19 20 P3.0-P3.7 5-1, 23-21
20 23 24 6, 4-1, 27-25
I I I I/O
RST
9
11
I
X1
11
13
I
X2
10
12
O
NOTE: 1. When P0.2 is at or close to 0V it may affect the internal ROM operation. We recommend that P0.2 be tied to VCC via a small pullup (e.g., 2k).
1998 May 01
5
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
ABSOLUTE MAXIMUM RATINGS1, 2
PARAMETER Storage temperature range Voltage from VCC to VSS Voltage from any pin to VSS (except VPP) Power dissipation Voltage on VPP pin to VSS Maximum IOL per I/O pin RATING -65 to +150 -0.5 to +6.5 -0.5 to VCC + 0.5 1.0 0 to +13.0 10 UNIT C V V W V mA
NOTES: 1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section of this specification is not implied. 2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maxima.
DC ELECTRICAL CHARACTERISTICS
Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10% for 87C751, VCC = 5V 10% for 83C751, VSS = 0V1 LIMITS SYMBOL VIL VIH VIH1 VIL1 VIH2 VOL VOL1 VOH PARAMETER Input low voltage, except SDA, SCL Input high voltage, except X1, RST Input high voltage, X1, RST SDA, SCL, P0.2 Input low voltage Input high voltage Output low voltage, ports 1 and 3 Output low voltage, port 0.2 Output high voltage, ports 1 and 3 IOL = 1.6mA2 IOL = 3.2mA2 IOH = -60A IOH = -25A IOH = -10A IOL = 3mA (over VCC range) VIN = 0.45V VIN = 2V (0 to 70C) VIN = 2V (-40 to +85C) 0.45 < VIN < VCC 25 Test freq = 1MHz, Tamb = 25C VCC = 2 to VCC max VSS = 0V VCC = 5V10% Tamb = 21C to 27C VPP = 13.0V 12.5 2.4 0.75VCC 0.9VCC 0.4 10 -50 -650 -750 10 175 10 50 13.0 50 TEST CONDITIONS MIN -0.5 0.2VCC+0.9 0.7VCC -0.5 0.7VCC MAX 0.2VDD-0.1 VCC+0.5 VCC+0.5 0.3VCC VCC+0.5 0.45 0.45 V V V V V V V V V V V pF A A A A k pF A V mA UNIT
VOL2 C IIL ITL ILI RRST CIO IPD VPP IPP ICC
Port 0.0 and 0.1 (I2C) - Drivers Output low voltage Driver, receiver combined: Capacitance Logical 0 input current, ports 1 and 3 Logical 1 to 0 transition current, ports 1 and 33 Input leakage current, port 0 Internal pull-down resistor Pin capacitance Power-down current4 VPP program voltage (for 87C751 only) Program current (for 87C751 only) Supply current (see Figure 2)
NOTES TO DC ELECTRICAL CHARACTERISTICS ON NEXT PAGE.
1998 May 01
6
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
NOTES TO DC ELECTRICAL CHARACTERISTICS: 1. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. 2. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10mA (NOTE: This is 85C spec.) 26mA Maximum IOL per 8-bit port: 67mA Maximum total IOL for all outputs: If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 3. Pins of ports 1 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its maximum value when VIN is approximately 2V. 4. Power-down ICC is measured with all output pins disconnected; port 0 = VCC; X2, X1 n.c.; RST = VSS. 5. Active ICC is measured with all output pins disconnected; X1 driven with tCLCH, tCHCL = 5ns, VIL = VSS + 0.5V, VIH = VCC - 0.5V; X2 n.c.; RST = port 0 = VCC. ICC will be slightly higher if a crystal oscillator is used. 6. Idle ICC is measured with all output pins disconnected; X1 driven with tCLCH, tCHCL = 5ns, VIL = VSS + 0.5V, VIH = VCC - 0.5V; X2 n.c.; port 0 = VCC; RST = VSS.
AC ELECTRICAL CHARACTERISTICS
Tamb = 0C to +70C or -40C to +85C, VCC = 5V 10% for 87C751, VCC = 5V 10% for 83C751, VSS = 0V1, 2 12MHz CLOCK SYMBOL 1/tCLCL Oscillator frequency: PARAMETER MIN MAX VARIABLE CLOCK MIN 3.5 3.5 MAX 12 16 UNIT MHz MHz
External Clock (Figure 1) tCHCX tCLCX tCLCH tCHCL High time Low time Rise time Fall time 20 20 20 20 20 20 20 20 ns ns ns ns
NOTES: 1. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. 2. Load capacitance for ports = 80pF.
1998 May 01
7
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
EXPLANATION OF THE AC SYMBOLS
Each timing symbol has five characters. The first character is always `t' (= time). The other characters, depending on their positions, indicate the name of a signal or the logical status of that signal. The designations are: C - Clock D - Input data H - Logic level high L - Logic level low Q - Output data T - Time V - Valid X - No longer a valid logic level Z - Float
VCC -0.5 0.2 VCC + 0.9 0.2 VCC - 0.1 0.45V
tCLCX
tCHCX tCHCL tCLCL tCLCH
SU00297
Figure 1. External Clock Drive
22 20 18 16 14 ICC (mA) 12 10 8 6 4 2
MAX ACTIVE ICC5
TYP ACTIVE ICC5
MAX IDLE ICC6
TYP IDLE ICC6 4MHz 8MHz FREQ 12MHz 16MHz
SU00298
Figure 2. ICC vs. FREQ Maximum ICC values taken at VCC max and worst case temperature. Typical ICC values taken at VCC = 5.0V and 25C. Notes 5 and 6 refer to DC Electrical Characteristics.
1998 May 01
8
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
OSCILLATOR CHARACTERISTICS
X1 and X2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator. To drive the device from an external clock source, X1 should be driven while X2 is left unconnected. There are no requirements on the duty cycle of the external clock signal, because the input to the internal clock circuitry is through a divide-by-two flip-flop. However, minimum and maximum high and low times specified in the data sheet must be observed.
should be noted that stack depth is limited to 64 bytes, the amount of available RAM. A reset loads the stack pointer with 07 (which is pre-incremented on a PUSH instruction).
(FFH) 255 Special Function Registers (80H) 128
RESET
A reset is accomplished by holding the RST pin high for at least two machine cycles (24 oscillator periods), while the oscillator is running. To insure a good power-up reset, the RST pin must be high long enough to allow the oscillator time to start up (normally a few milliseconds) plus two machine cycles. At power-up, the voltage on VCC and RST must come up at the same time for a proper start-up.
(3FH) 63 Internal Data RAM
(00H) 0
SU00299
IDLE MODE
In idle mode, the CPU puts itself to sleep while all of the on-chip peripherals stay active. The instruction to invoke the idle mode is the last instruction executed in the normal operating mode before the idle mode is activated. The CPU contents, the on-chip RAM, and all of the special function registers remain intact during this mode. The idle mode can be terminated either by any enabled interrupt (at which time the process is picked up at the interrupt service routine and continued), or by a hardware reset which starts the processor in the same manner as a power-on reset.
Figure 3. Memory Map
Program Memory
On the 8XC751, program memory is 2048 bytes long and is not externally expandable, so the 80C51 instructions MOVX, LJMP, and LCALL are not implemented. The only fixed locations in program memory are the addresses at which execution is taken up in response to reset and interrupts, which are as follows: Program Memory Event Address Reset 000 External INT0 003 Counter/timer 0 00B External INT1 013 Timer I 01B I2C serial 023
POWER-DOWN MODE
In the power-down mode, the oscillator is stopped and the instruction to invoke power-down is the last instruction executed. Only the contents of the on-chip RAM are preserved. A hardware reset is the only way to terminate the power-down mode. the control bits for the reduced power modes are in the special function register PCON.
Counter/Timer Subsystem
The 8XC751 has one counter/timer called timer/counter 0. Its operation is similar to mode 2 operation on the 80C51, but is extended to 16 bits with 16 bits of autoload. The controls for this counter are centralized in a single register called TCON. A watchdog timer, called Timer I, is for use with the I2C subsystem. In I2C applications, this timer is dedicated to time-generation and bus monitoring of the I2C. In non-I2C applications, it is available for use as a fixed time-base.
Table 1.
MODE Idle Power-down
External Pin Status During Idle and Power-Down Modes
Port 0 Data Data Port 1 Data Data Port 2 Data Data
Counter Timer - Special Function Register DIFFERENCES BETWEEN THE 8XC751 AND THE 80C51 Memory Organization
The central processing unit (CPU) manipulates operands in two address spaces as shown in Figure 3. The part's internal memory space consists of 2k bytes of program memory, and 64 bytes of data RAM overlapped with the 128-byte special function register area. The differences from the 80C51 are in RAM size (64 bytes vs. 128 bytes), in external RAM access (not available on the 83C751), in internal ROM size (2k bytes vs. 4k bytes), and in external program memory expansion (not available on the 83C751). The 128-byte special function register (SFR) space is accessed as on the 80C51 with some of the registers having been changed to reflect changes in the 83C751 peripheral functions. The stack may be located anywhere in internal RAM by loading the 8-bit stack pointer (SP). It The counter/timer has only one mode of operation, so the TMOD SFR is not used. There is also only one counter/timer, so there is no need for the TL1 and TH1 SFRs found on the 80C51. These have been replaced on the 83C751 by RTL and RTH, the counter/timer reload registers. Table 3 shows the special function registers, their locations, and reset values.
Interrupt Subsystem - Fixed Priority
The IP register and the 2-level interrupt system of the 80C51 are eliminated. Simultaneous interrupt conditions are resolved by a single-level, fixed priority as follows: Highest priority: Pin INT0 Counter/timer flag 0 Pin INT1 Timer I Serial I2C
Lowest priority:
1998 May 01
9
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
Special Function Register - Interrupt Subsystem
Because the interrupt structure is single level on the 83C751, there is no need for the IP SFR, so it is not used.
been replaced by I2CON and I2DAT, and two additional I2C registers have been added (I2STA and I2CFG).
I/O Port Latches (P0, P1, P3)
The port latches function the same as those on the 80C51. Since there is no port 2 on the 83C751, the P2 latch is not used. Port 0 on the 83C751 has only 3 bits, so only 3 bits of the P0 SFR have a useful function.
Serial Communications
The 8XC751 contains an I2C serial communications port instead of the 80C51 UART. The I2C serial port is a single bit hardware interface with all of the hardware necessary to support multimaster and slave operations. Also included are receiver digital filters and timer (timer I) for communication watch-dog purposes. The I2C serial port is controlled through four special function registers; I2C control, I2C data, I2C status, and I2C configuration.
Special Function Register - I/O Port Latches
There is no Port2 on the 8XC751, so P2 is not used. Also, only 3 bits of P0 SFR have a useful function.
Special Function Register - Serial Communications
The 83C751 contains many of the special function registers (SFR) that are found on the 80C51. Due to the different peripheral features on the 83C751, there are several additional SFRs and several that have been changed. Since the standard UART found on the 80C51 has been replaced by the I2C serial interface, the UART SFRs, SCON, and SBUF have
Data Pointer (DPTR)
The data pointer (DPTR) consists of a high byte (DPH) and a low byte (DPL). In the 80C51 this register allows the access of external data memory using the MOVX instruction. Since the 83C751 does not support MOVX or external memory accesses, this register is generally used as a 16-bit offset pointer of the accumulator in a MOVC instruction. DPTR may also be manipulated as two independent 8-bit registers.
Table 2. I2C Special Function Register Addresses
REGISTER ADDRESS NAME I2C control I2C data I2C configuration I2C status SYMBOL I2CON I2DAT I2CFG I2STA ADDRESS 98 99 D8 F8 MSB 9F - DF FF 9E - DE FE 9D - DD FD 9C - DC FC 9B - DB FB BIT ADDRESS LSB 9A - DA FA 99 - D9 F9 98 - D8 F8
ROM CODE SUBMISSION
When submitting ROM code for the 80C751, the following must be specified: 1. 2k byte user ROM data ADDRESS 0000H to 07FFH CONTENT DATA BIT(S) 7:0 COMMENT User ROM Data
1998 May 01
10
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
Table 3.
SYMBOL ACC* B* DPTR: DPH DPL I2CFG*#
8XC751 Special Function Registers
DESCRIPTION Accumulator B register Data pointer (2 bytes) High byte Low byte I2C configuration DIRECT BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION ADDRESS MSB LSB E0H F0H E7 F7 E6 F6 E5 F5 E4 F4 E3 F3 E2 F2 E1 F1 E0 F0 RESET VALUE 00H 00H
83H 82H DF D8H/RD WR
SLAVEN SLAVEN
00H 00H DE
MASTRQ MASTRQ
DD 0 CLRTI
DC TIRUN TIRUN
DB - -
DA - -
D9 CT1 CT1
D8 CT0 CT0 0000xx00B
9F I2CON*# I2C control 98H/RD WR I2DAT# I2C data RDAT CXA
9E ATN IDLE
9D DRDY CDR
9C ARL CARL
9B STR CSTR
9A STP CSTP
99
MASTER
98 - XSTP 81H
XSTR
99H/RD WR
RDAT XDAT FF
0 X FE IDLE AE -
0 X FD XDATA AD -
0 X FC XACTV AC EI2
0 X FB
MAKSTR
0 X FA
MAKSTP
0 X F9 XSTR A9 ET0 81 SDA 91 - B1
0 X F8 XSTP A8 EX0 80 SCL 90 - B0
80H
I2STA*#
I2C status
F8H
- AF
x0100000B
AB ET1
AA EX1 82
IE*#
Interrupt enable
ABH
EA
00H
P0*#
Port 0
80H
- 97
- 96 INT1 B6
- 95 INT0 B5
- 94 - B4
- 93 - B3
- 92 - B2
xxxxx111B
P1* P3*
Port 1 Port 3
90H B0H
T0 B7
FFH FFH
PCON#
Power control
87H
-
-
-
-
-
-
PD
IDL
xxxxxx00B
D7 PSW* Program status word D0H CY
D6 AC
D5 F0
D4 RS1
D3 RS0
D2 OV
D1 -
D0 P 00H
SP
Stack pointer
81H 8F 8E C/T 8D TF 8C TR 8B IE0 8A IT0 89 IE1 88 IT1
07H
TCON*#
Timer/counter control
88H
GATE
00H
TL# TH# RTL#
Timer low byte Timer high byte Timer low reload
8AH 8CH 8BH
00H 00H 00H 00H
RTH# Timer high reload 8DH * SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs.
1998 May 01
11
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
I/O Port Structure The 8XC751 has two 8-bit ports (ports 1 and 3) and one 3-bit port (port 0). All three ports on the 8XC751 are bidirectional. Each consists of a latch (special function register P0, P1, P3), an output driver, and an input buffer. Three port 1 pins and two port 0 pins are multifunctional. In addition to being port pins, these pins serve the function of special features as follows: Port PinAlternate Function P0.0 P0.1 P1.5 P1.6 P1.7 I2C clock (SCL) I2C data (SDA) INT0 (external interrupt 0 input) INT1 (external interrupt 1 input) T0 (timer 0 external input)
TCON Register
MSB GATE C/T TF TR IE0 IT0 IE1 LSB IT1
GATE
1 0 1 0 1 0 1 0 1 1 0 1 1 0
C/T TF
TR IE0 IT0 IE1 IT1
Ports 1 and 3 are identical in structure to the same ports on the 80C51. The structure of port 0 on the 8XC751 is similar to that of the 80C51 but does not include address/data input and output circuitry. As on the 80C51, ports 1 and 3 are quasi-bidirectional while port 0 is bidirectional with no internal pullups. Timer/Counter The 8XC751 has two timers: a 16-bit timer/counter and a 10-bit fixed-rate timer. The 16-bit timer/counter's operation is similar to mode 2 operation on the 80C51, but is extended to 16 bits. The timer/counter is clocked by either 1/12 the oscillator frequency or by transitions on the T0 pin. The C/T pin in special function register TCON selects between these two modes. When the TCON TR bit is set, the timer/counter is enabled. Register pair TH and TL are incremented by the clock source. When the register pair overflows, the register pair is reloaded with the values in registers RTH and RTL. The value in the reload registers is left unchanged. See the 83C751 counter/timer block diagram in Figure 4. The TF bit in special function register TCON is set on counter overflow and, if the interrupt is enabled, will generate an interrupt.
- Timer/counter is enabled only when INT0 pin is high, and TR is 1. - Timer/counter is enabled when TR is 1. - Counter/timer operation from T0 pin. - Timer operation from internal clock. - Set on overflow of TH. - Cleared when processor vectors to interrupt routine and by reset. - Timer/counter enabled. - Timer/counter disabled. - Edge detected in INT0. - INT0 is edge triggered. - INT0 is level sensitive. - Edge detected on INT1. - INT1 is edge triggered. - INT1 is level sensitive.
These flags are functionally identical to the corresponding 80C51 flags, except that there is only one timer on the 83C751 and the flags are therefore combined into one register. Note that the positions of the IE0/IT0 and IE1/IT1 bits are transposed from the positions used in the standard 80C51 TCON register. Timer I is used to control the timing of the I2C bus and also to detect a "bus locked" condition, by causing an interrupt when nothing happens on the I2C bus for an inordinately long period of time while a transmission is in progress. If the interrupt does not occur, the program can attempt to correct the fault and allow the last I2C transmission to be repeated. The I2C watchdog timer, timer I, is also available as a general-purpose fixed-rate timer when the I2C interface is not being used. A clock rate of 1/12 the oscillator frequency forms the input to the timer. Timer I has a timeout interval of 1024 machine cycles when used as a fixed-rate timer.
OSC
/ 12 C/T = 0 TL C/T = 1 TH TF Int.
T0 Pin TR Reload
Gate INT0 Pin
RTL
RTH
SU00300
Figure 4. 83C751 Counter/Timer Block Diagram
1998 May 01
12
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
I2C Serial Interface The I2C bus uses two wires (SDA and SCL) to transfer information between devices connected to the bus. The main features of the bus are:
performance of the I2C bus. See special function register I2CFG description for prescale values (CT0, CT1). The MAXIMUM SCL CHANGE time is important, but its exact span is not critical. The complete 10 bits of timer I are used to count out the maximum time. When I2C operation is enabled, this counter is cleared by transitions on the SCL pin. The timer does not run between I2C frames (i.e., whenever reset or stop occurred more recently than the last start). When this counter is running, it will carry out after 1020 to 1023 machine cycles have elapsed since a change on SCL. A carry out causes a hardware reset of the 83C751 I2C interface and generates an interrupt if the timer I interrupt is enabled. In cases where the bus hangup is due to a lack of software response by this 83C751, the reset releases SCL and allows I2C operation among other devices to continue. I2C Interrupts If I2C interrupts are enabled (EA and EI2 are both set to 1), an I2C interrupt will occur whenever the ATN flag is set by a start, stop, arbitration loss, or data ready condition (refer to the description of ATN following). In practice, it is not efficient to operate the I2C interface in this fashion because the I2C interrupt service routine would somehow have to distinguish between hundreds of possible conditions. Also, since I2C can operate at a fairly high rate, the software may execute faster if the code simply waits for the I2C interface. Typically, the I2C interrupt should only be used to indicate a start condition at an idle slave device, or a stop condition at an idle master device (if it is waiting to use the I2C bus). This is accomplished by enabling the I2C interrupt only during the aforementioned conditions. I2C Register I2CON
7 Read Write RDAT CXA 6 ATN IDLE 5 DRDY CDR 4 ARL CARL 3 STR CSTR 2 STP CSTP 1 MASTER XSTR 0 - XSTP
* Bidirectional data transfer between masters and slaves * Serial addressing of slaves (no added wiring) * Acknowledgment after each transferred byte * Multimaster bus * Arbitration between simultaneously transmitting masters without
corruption of serial data on bus
* The 82B715 extends communication distance to 100 feet (30M).
A large family of I2C compatible ICs is available. See the I2C section of this manual for more details on the bus and available ICs. The 83C751 I2C subsystem includes hardware to simplify the software required to drive the I2C bus. The hardware is a single bit interface which in addition to including the necessary arbitration and framing error checks, includes clock stretching and a bus timeout timer. The interface is synchronized to software either through polled loops or interrupts. Refer to the application note AN422, in Section 4, entitled "Using the 8XC751 Microcontroller as an I2C Bus Master" for additional discussion of the 83C751 I2C interface and sample driver routines. Six time spans are important in timer I: I2C operation and are insured by
* The MINIMUM HIGH time for SCL when this device is the master. * The MINIMUM LOW time for SCL when this device is a master.
This is not very important for a single-bit hardware interface like this one, because the SCL low time is stretched until the software responds to the I2C flags. The software response time normally meets or exceeds the MIN LO time. In cases where the software responds within MIN HI + MIN LO) time, timer I will ensure that the minimum time is met.
* The MINIMUM SCL HIGH TO SDA HIGH time in a stop condition. * The MINIMUM SDA HIGH TO SDA LOW time between I2C stop
and start conditions (4.7s, see spec.).
Reading I2CON RDAT The data from SDA is captured into "Receive DATa" whenever a rising edge occurs on SCL. RDAT is also available (with seven low-order zeros) in the I2DAT register. The difference between reading it here and there is that reading I2DAT clears DRDY, allowing the I2C to proceed on to another bit. Typically, the first seven bits of a received byte are read from I2DAT, while the 8th is read here. Then I2DAT can be written to send the Ack bit and clear DRDY. "ATteNtion" is 1 when one or more of DRDY, ARL, STR, or STP is 1. Thus, ATN comprises a single bit that can be tested to release the I2C service routine from a "wait loop." "Data ReaDY" (and thus ATN) is set when a rising edge occurs on SCL, except at idle slave. DRDY is cleared by writing CDR = 1, or by writing or reading the I2DAT register. The following low period on SCL is stretched until the program responds by clearing DRDY.
* The MINIMUM SDA LOW TO SCL LOW time in a start condition. * The MAXIMUM SCL CHANGE time while an I2C frame is in
progress. A frame is in progress between a start condition and the following stop condition. This time span serves to detect a lack of software response on this 8XC751 as well as external I2C problems. SCL "stuck low" indicates a faulty master or slave. SCL "stuck high" may mean a faulty device, or that noise induced onto the I2C bus caused all masters to withdraw from I2C arbitration. The first five of these times are 4.7s (see I2C specification) and are covered by the low order three bits of timer I. Timer I is clocked by the 8XC751 oscillator, which can vary in frequency from 0.5 to 16MHz. Timer I can be preloaded with one of four values to optimize timing for different oscillator frequencies. At lower frequencies, software response time is increased and will degrade maximum ATN
DRDY
1998 May 01
13
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
Checking ATN and DRDY When a program detects ATN = 1, it should next check DRDY. If DRDY = 1, then if it receives the last bit, it should capture the data from RDAT (in I2DAT or I2CON). Next, if the next bit is to be sent, it should be written to I2DAT. One way or another, it should clear DRDY and then return to monitoring ATN. Note that if any of ARL, STR, or STP is set, clearing DRDY will not release SCL to high, so that the I2C will not go on to the next bit. If a program detects ATN = 1, and DRDY = 0, it should go on to examine ARL, STR, and STP. ARL "Arbitration Loss" is 1 when transmit Active was set, but this 83C751 lost arbitration to another transmitter. Transmit Active is cleared when ARL is 1. There are four separate cases in which ARL is set. 1. If the program sent a 1 or repeated start, but another device sent a 0, or a stop, so that SDA is 0 at the rising edge of SCL. (If the other device sent a stop, the setting of ARL will be followed shortly by STP being set.) 2. If the program sent a 1, but another device sent a repeated start, and it drove SDA low before the 83C751 could drive SCL low. (This type of ARL is always accompanied by STR = 1.) 3. In master mode, if the program sent a repeated start, but another device sent a 1, and it drove SCL low before this 83C751 could drive SDA low. 4. In master mode, if the program sent stop, but it could not be sent because another device sent a 0. "STaRt" is set to a 1 when an I2C start condition is detected at a non-idle slave or at a master. (STR is not set when an idle slave becomes active due to a start bit; the slave has nothing useful to do until the rising edge of SCL sets DRDY.) "SToP" is set to 1 when an I2C stop condition is detected at a non-idle slave or at a master. (STP is not set for a stop condition at an idle slave.)
Regarding Transmit Active Transmit Active is set by writing the I2DAT register, or by writing I2CON with XSTR = 1 or XSTP = 1. The I2C interface will only drive the SDA line low when Transmit Active is set, and the ARL bit will only be set to 1 when Transmit Active is set. Transmit Active is cleared by reading the I2DAT register, or by writing I2CON with CXA = 1. Transmit Active is automatically cleared when ARL is 1. IDLE Writing 1 to "IDLE" causes a slave's I2C hardware to ignore the I2C until the next start condition (but if MASTRQ is 1, then a stop condition will make the 83C751 into a master). Writing a 1 to "Clear Data Ready" clears DRDY. (Reading or writing the I2DAT register also does this.) Writing a 1 to "Clear Arbitration Loss" clears the ARL bit. Writing a 1 to "Clear STaRt" clears the STR bit. Writing a 1 to "Clear SToP" clears the STP bit. Note that if one or more of DRDY, ARL, STR, or STP is 1, the low time of SCL is stretched until the service routine responds by clearing them. Writing 1s to "Xmit repeated STaRt" and CDR tells the I2C hardware to send a repeated start condition. This should only be at a master. Note that XSTR need not and should not be used to send an "initial" (nonrepeated) start; it is sent automatically by the I2C hardware. Writing XSTR = 1 includes the effect of writing I2DAT with XDAT = 1; it sets Transmit Active and releases SDA to high during the SCL low time. After SCL goes high, the I2C hardware waits for the suitable minimum time and then drives SDA low to make the start condition. Writing 1s to "Xmit SToP" and CDR tells the I2C hardware to send a stop condition. This should only be done at a master. If there are no more messages to initiate, the service routine should clear the MASTRQ bit in I2CFG to 0 before writing XSTP with 1. Writing XSTP = 1 includes the effect of writing I2DAT with XDAT = 0; it sets Transmit Active and drives SDA low during the SCL low time. After SCL goes high, the I2C hardware waits for the suitable minimum time and then releases SDA to high to make the stop condition.
CDR CARL CSTR CSTP
XSTR
STR
XSTP
STP
MASTER "MASTER" is 1 if this 83C751 is currently a master on the I2C. MASTER is set when MASTRQ is 1 and the bus is not busy (i.e., if a start bit hasn't been received since reset or a "Timer I" time-out, or if a stop has been received since the last start). MASTER is cleared when ARL is set, or after the software writes MASTRQ = 0 and then XSTP = 1. Writing I2CON Typically, for each bit in an I2C message, a service routine waits for ATN = 1. Based on DRDY, ARL, STR, and STP, and on the current bit position in the message, it may then write I2CON with one or more of the following bits, or it may read or write the I2DAT register. CXA Writing a 1 to "Clear Xmit Active" clears the Transmit Active state. (Reading the I2DAT register also does this.)
NOTE: Because of the manner in which register bit addressing is implemented in the 80C51 family, the I2CON register should never be altered by use of the SETB, CLR, CPL, MOV (bit), or JBC instructions. This is due to the fact that read and write functions of this register are different. Testing of I2CON bits via the JB and JNB instructions is supported.
1998 May 01
14
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
I2C Register I2DAT
7 Read Write RDAT XDAT 6 0 X 5 0 X 4 0 X 3 0 X 2 0 X 1 0 X 0 0 X
I2C Register I2CFG
7 Read Write SLAVEN SLAVEN 6 MASTRQ MASTRQ 5 0 CLRTI 4 TIRUN TIRUN 3 - - 2 - - 1 CT1 CT1 0 CT0 CT0
RDAT
"Receive DATa" is captured from SDA every rising edge of SCL. Reading I2DAT also clears DRDY and the Transmit Active state. "Xmit Data" sets the data for the next bit. Writing I2DAT also clears DRDY and sets the Transmit Active state.
XDAT
SLAVEN Writing a 1 to "SLAVe ENable" enables the slave functions of the I2C subsystem. If SLAVEN and MASTRQ are 0, the I2C hardware is disabled. This bit is cleared to 0 by reset and by an I2C time-out. MASTRQ Writing a 1 to "MASTRQ" requests mastership of the I2C. If a frame from another master is in progress when this bit is changed from 0 to 1, action is delayed until a stop condition is detected. Then, or immediately if a frame is not in progress, a start condition is sent and DRDY is set (thus making ATN 1 and generating an I2C interrupt). When a master wishes to release mastership status of the I2C, it writes a 1 to XSTP in I2CON. MASTRQ is cleared by reset and by an I2C time-out. CLRTI TIRUN Writing a 1 to this bit clears the Timer I interrupt flag. This bit position always reads as a 0. Writing a 1 to this bit lets Timer I run; a zero stops and clears it. Together with SLAVEN, MASTRQ, and MASTER, this bit determines operational modes as shown in Table 4. These two bits are programmed as a function of the OSC rate, to optimize the MIN HI and LO time of SCL when this 83C751 is a master on the I2C. The time value determined by these bits controls both of these parameters, and also the timing for stop and start conditions. These bits are cleared to 00 by reset.
Regarding Software Response Time Because the 83C751 can run at 16MHz, and because the I2C interface is optimized for high-speed operation, it is quite likely that an I2C service routine will sometimes respond to DRDY (which is set at a rising edge of SCL) and write I2DAT before SCL has gone low again. If XDAT were applied directly to SDA, this situation would produce an I2C protocol violation. The programmer need not worry about this possibility because XDAT is applied to SDA only when SCL is low. Conversely, a program that includes an I2C service routine may take a long time to respond to DRDY. Typically, an I2C routine operates on a flag-polling basis during a message, with interrupts from other peripheral functions enabled. If an interrupt occurs, it will delay the response of the I2C service routine. The programmer need not worry about this very much either, because the I2C hardware stretches the SCL low time until the service routine responds. The only constraint on the response is that it must not exceed the Timer I time-out, which is at least 765 microseconds.
CT1,0
Values to be used in the CT1 and CT0 bits are shown in Table 5. To allow the I2C bus to run at the maximum rate for a particular oscillator frequency, compare the actual oscillator rate to the fOSC max column in the table. The value for CT1 and CT0 is found in the first line of the table where fOSC max is greater than or equal to the actual frequency. The table also shows the osc/12 count for various settings of CT1/CT0. This allows calculation of the actual minimum high and low times for SCL as follows: SCL min high/low time (in microseconds) = 12 * count / osc (in MHz) For instance, at a 16MHz frequency, with CT1/CT0 set to 10, the minimum SCL high and low times will be 5.25s. The table also shows the Timer I timeout period (given in machine cycles) for each CT1/CT0 combination. The timeout period varies because of the way in which minimum SCL high and low times are measured. When the I2C interface is operating, Timer I is preloaded at every SCL transition with a value dependent upon CT1/CT0. The preload value is chosen such that a minimum SCL high or low time has elapsed when Timer I reaches a count of 008 (the actual value preloaded into Timer I is 8 minus the osc/12 count).
1998 May 01
15
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
Table 4.
SLAVEN, MASTRQ, MASTER All 0 All 0 Any or all 1 Any or all 1
Interaction of TIRUN with SLAVEN, MASTRQ, and MASTER
TIRUN 0 1 0 1 OPERATING MODE The I2C interface is disabled. Timer I is cleared and does not run. This is the state assumed after a reset. If an I2C application wants to ignore the I2C at certain times, it should write SLAVEN, MASTRQ, and TIRUN all to zero. The I2C interface is disabled. Timer I operates as a free-running time base. Use this mode only in non-I2C applications. The I2C interface is enabled. The 3 low-order bits of Timer I run for min-time generation, but the hi-order bits do not, so that there is no checking for I2C being "hung." This configuration can be used for very slow I2C operation. The I2C interface is enabled. Timer I runs during frames on the I2C, and is cleared by transitions on SCL, and by Start and Stop conditions. This is the normal state for I2C operation.
Table 5.
CT1, CT0 Values
CT1, CT0 10 01 00 11 OSC/12 COUNT 7 6 5 4 fOSC MAX 16.8MHz 14.4MHz 12.0MHz 9.6MHz TIMEOUT PERIOD 1023 cycles 1022 cycles 1021 cycles 1020 cycles
I2C Register I2STA READ ONLY
7 - MSB 6 IDLE 5 XDATA 4 XACTV 3 MAKSTR 2 MAKSTP 1 XSTR 0 XSTP LSB
The interrupt enable register (IE) is used to individually enable or disable the five sources. Bit EA in the interrupt enable register can be used to globally enable or disable all interrupt sources. The interrupt enable register is described below. All other interrupt details are based on the 80C51 interrupt architecture. Interrupt Enable Register
7 EA 6 X 5 X 4 EI2 3 ETI 2 EX1 1 ET0 0 EX0
This register is read only and reflects the internal status of the hardware. IDLE, XSTR, and XSTP reflect the status of the like named bits in the I2CON register.
I2C
XDATA The content of the transmitter buffer. XACTV Transmitter active. MAKSTR This bit is high while the hardware is effecting a start condition. MAKSTP This bit is high while the hardware is effecting a stop condition. XSTR This bit is active while the hardware is effecting a repeated start condition. XSTP This bit is active while the hardware is effecting a repeated stop condition. Interrupts The interrupt structure is a five-source, one-level interrupt system. Interrupt sources common to the 80C51 are the external interrupts (INT0, INT1) and the timer/counter interrupt (ET0). The I2C interrupt (EI2) and Timer I interrupt (ETI) are the other two interrupt sources. The interrupt sources are listed below in their order of polling sequence priority. Upon interrupt or reset the program counter is loaded with specific values for the appropriate interrupt service routine in program memory. These values are: Event Reset INT0 Counter/Timer 0 INT1 Timer I I2C 1998 May 01 Program Memory Address 000 003 00B 013 01B 023 Priority Highest
Symbol Position EA IE.7
Function Disables all interrupts. If EA = 0, no interrupt will be acknowledged. If EA = 1, each interrupt source is individually enabled or disabled by setting or clearing its enable bit Reserved Reserved Enables or disables the I2C interrupt. If EI2 = 0, the I2C interrupt is disabled Enables or disables the Timer I overflow interrupt. If ETI = 0, the Timer I interrupt is disabled. Enables or disables external interrupt 1. If EX1 = 0, external interrupt 1 is disabled. Enables or disables the Timer 0 overflow interrupt. If ET0 = 0, theTimer 0 interrupt is disabled. Enables or disables external interrupt 0. If EX0 = 0, external interrupt 0 is disabled.
- - EI2 ETI
IE.6 IE.5 IE.4 IE.3
EX1 ET0
IE.2 IE.1
EX0
IE.0
Lowest 16
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
87C751 PROGRAMMING CONSIDERATIONS EPROM Characteristics
The 87C751 is programmed by using a modified Quick-Pulse Programming algorithm similar to that used for devices such as the 87C451 and 87C51. It differs from these devices in that a serial data stream is used to place the 87C751 in the programming mode. Figure 5 shows a block diagram of the programming configuration for the 87C751. Port pin P0.2 is used as the programming voltage supply input (VPP signal). Port pin P0.1 is used as the program (PGM/) signal. This pin is used for the 25 programming pulses. Port 3 is used as the address input for the byte to be programmed and accepts both the high and low components of the eleven bit address. Multiplexing of these address components is performed using the ASEL input. The user should drive the ASEL input high and then drive port 3 with the high order bits of the address. ASEL should remain high for at least 13 clock cycles. ASEL may then be driven low which latches the high order bits of the address internally. the high address should remain on port 3 for at least two clock cycles after ASEL is driven low. Port 3 may then be driven with the low byte of the address. The low address will be internally stable 13 clock cycles later. The address will remain stable provided that the low byte placed on port 3 is held stable and ASEL is kept low. Note: ASEL needs to be pulsed high only to change the high byte of the address. Port 1 is used as a bidirectional data bus during programming and verify operations. During programming mode, it accepts the byte to be programmed. During verify mode, it provides the contents of the EPROM location specified by the address which has been supplied to Port 3. The XTAL1 pin is the oscillator input and receives the master system clock. This clock should be between 1.2 and 6MHz. The RESET pin is used to accept the serial data stream that places the 87C751 into various programming modes. This pattern consists of a 10-bit code with the LSB sent first. Each bit is synchronized to the clock input, X1.
repeated until a total of 25 programming pulses have occurred. At the conclusion of the last pulse, the PGM/ signal should remain high. The VPP signal may now be driven to the VOH level, placing the 87C751 in the verify mode. (Port 1 is now used as an output port). After four machine cycles (48 clock periods), the contents of the addressed location in the EPROM array will appear on Port 1. The next programming cycle may now be initiated by placing the address information at the inputs of the multiplexed buffers, driving the VPP pin to the VPP voltage level, providing the byte to be programmed to Port1 and issuing the 26 programming pulses on the PGM/ pin, bringing VPP back down to the VC level and verifying the byte.
Programming Modes
The 87C751 has four programming features incorporated within its EPROM array. These include the USER EPROM for storage of the application's code, a 16-byte encryption key array and two security bits. Programming and verification of these four elements are selected by a combination of the serial data stream applied to the RESET pin and the voltage levels applied to port pins P0.1 and P0.2. The various combinations are shown in Table 6.
Encryption Key Table
The 87C751 includes a 16-byte EPROM array that is programmable by the end user. The contents of this array can then be used to encrypt the program memory contents during a program memory verify operation. When a program memory verify operation is performed, the contents of the program memory location is XNOR'ed with one of the bytes in the 16-byte encryption table. The resulting data pattern is then provided to port 1 as the verify data. The encryption mechanism can be disable, in essence, by leaving the bytes in the encryption table in their erased state (FFH) since the XNOR product of a bit with a logical one will result in the original bit. The encryption bytes are mapped with the code memory in 16-byte groups. the first byte in code memory will be encrypted with the first byte in the encryption table; the second byte in code memory will be encrypted with the second byte in the encryption table and so forth up to and including the 16the byte. The encryption repeats in 16-byte groups; the 17th byte in the code memory will be encrypted with the first byte in the encryption table, and so forth.
Programming Operation
Figures 6 and 7 show the timing diagrams for the program/verify cycle. RESET should initially be held high for at least two machine cycles. P0.1 (PGM/) and P0.2 (VPP) will be at VOH as a result of the RESET operation. At this point, these pins function as normal quasi-bidirectional I/O ports and the programming equipment may pull these lines low. However, prior to sending the 10-bit code on the RESET pin, the programming equipment should drive these pins high (VIH). The RESET pin may now be used as the serial data input for the data stream which places the 87C751 in the programming mode. Data bits are sampled during the clock high time and thus should only change during the time that the clock is low. Following transmission of the last data bit, the RESET pin should be held low. Next the address information for the location to be programmed is placed on port 3 and ASEL is used to perform the address multiplexing, as previously described. At this time, port 1 functions as an output. A high voltage VPP level is then applied to the VPP input (P0.2). (This sets Port 1 as an input port). The data to be programmed into the EPROM array is then placed on Port 1. This is followed by a series of programming pulses applied to the PGM/ pin (P0.1). These pulses are created by driving P0.1 low and then high. This pulse is
Security Bits
Two security bits, security bit 1 and security bit 2, are provided to limit access to the USER EPROM and encryption key arrays. Security bit 1 is the program inhibit bit, and once programmed performs the following functions: 1. Additional programming of the USER EPROM is inhibited. 2. Additional programming of the encryption key is inhibited. 3. Verification of the encryption key is inhibited. 4. Verification of the USER EPROM and the security bit levels may still be performed. (If the encryption key array is being used, this security bit should be programmed by the user to prevent unauthorized parties from reprogramming the encryption key to all logical zero bits. Such programming would provide data during a verify cycle that is the logical complement of the USER EPROM contents). Security bit 2, the verify inhibit bit, prevents verification of both the USER EPROM array and the encryption key arrays. The security bit levels may still be verified.
1998 May 01
17
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
Programming and Verifying Security Bits
Security bits are programmed employing the same techniques used to program the USER EPROM and KEY arrays using serial data streams and logic levels on port pins indicated in Table 6. When programming either security bit, it is not necessary to provide address or data information to the 87C751 on ports 1 and 3. Verification occurs in a similar manner using the RESET serial stream shown in Table 6. Port 3 is not required to be driven and the results of the verify operation will appear on ports 1.6 and 1.7. Ports 1.7 contains the security bit 1 data and is a logical one if programmed and a logical zero if not programmed. Likewise, P1.6 contains the security bit 2 data and is a logical one if programmed and a logical zero if not programmed.
Erasure Characteristics
Erasure of the EPROM begins to occur when the chip is exposed to light with wavelengths shorter than approximately 4,000 angstroms. Since sunlight and fluorescent lighting have wavelengths in this range, exposure to these light sources over an extended time (about 1 week in sunlight, or 3 years in room level fluorescent lighting) could cause inadvertent erasure. For this and secondary effects, it is recommended that an opaque label be placed over the window. For elevated temperature or environments where solvents are being used, apply Kapton tape Flourless part number 2345-5 or equivalent. The recommended erasure procedure is exposure to ultraviolet light (at 2537 angstroms) to an integrated dose of at least 15W-s/cm2. Exposing the EPROM to an ultraviolet lamp of 12,000W/cm2 rating for 20 to 39 minutes, at a distance of about 1 inch, should be sufficient. Erasure leaves the array in an all 1s state.
Table 6. Implementing Program/Verify Modes
OPERATION Program user EPROM Verify user EPROM Program key EPROM Verify key EPROM Program security bit 1 Program security bit 2 Verify security bits NOTE: * Pulsed from VIH to VIL and returned to VIH.
87C751 A0-A10 ADDRESS STROBE P3.0-P3.7 P0.0/ASEL VCC VSS +5V
SERIAL CODE 296H 296H 292H 292H 29AH 298H 29AH
P0.1 (PGM/) -* VIH -* VIH -* -* VIH
P0.2 (VPP) VPP VIH VPP VIH VPP VPP VIH
PROGRAMMING PULSES VPP/VIH VOLTAGE SOURCE CLK SOURCE
P0.1 P0.2 XTAL1
P1.0-P1.7
DATA BUS
RESET CONTROL LOGIC
RESET
SU00317
Figure 5. Programming Configuration
XTAL1 MIN 2 MACHINE CYCLES RESET BIT 0 BIT 1 BIT 2
TEN BIT SERIAL CODE BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9
P0.2
UNDEFINED
P0.1
UNDEFINED
SU00302
Figure 6. Entry into Program/Verify Modes 1998 May 01 18
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
EPROM PROGRAMMING AND VERIFICATION
Tamb = 21C to +27C, VCC = 5V 10%, VSS = 0V SYMBOL 1/tCLCL tAVGL1 tGHAX tDVGL tGHDX tSHGL tGHSL tGLGH tAVQV2 tGHGL tMASEL tHAHLD tHASET PARAMETER Oscillator/clock frequency Address setup to P0.1 (PROG-) low Address hold after P0.1 (PROG-) high Data setup to P0.1 (PROG-) low Data hold after P0.1 (PROG-) high VPP setup to P0.1 (PROG-) low VPP hold after P0.1 (PROG-) P0.1 (PROG-) width VPP low (VCC) to data valid P0.1 (PROG-) high to P0.1 (PROG-) low ASEL high time Address hold time Address setup to ASEL 10 13tCLCL 2tCLCL 13tCLCL 48tCLCL MIN 1.2 10s + 24tCLCL 48tCLCL 38tCLCL 36tCLCL 10 10 90 110 48tCLCL s s s s MAX 6 UNIT MHz
tADSTA Low address to valid data NOTES: 1. Address should be valid at least 24tCLCL before the rising edge of P0.2 (VPP). 2. For a pure verify mode, i.e., no program mode in between, tAVQV is 14tCLCL maximum.
12.75V P0.2 (VPP) 5V tSHGL 25 PULSES 5V tGHSL
P0.1 (PGM)
tMASEL P0.0 (ASEL) tAVGL
tGLGH
98s MIN 10s MIN
tGHGL
tHASET PORT 3 HIGH ADDRESS
tHAHLD LOW ADDRESS
tADSTA PORT 1 INVALID DATA VERIFY MODE VALID DATA
tDVGL
tGHDX
tAVQV INVALID DATA VERIFY MODE VALID DATA
DATA TO BE PROGRAMMED PROGRAM MODE
SU00303
Figure 7. Program/Verify Cycle
Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specifications defined by Philips. This specification can be ordered using the code 9398 393 40011.
1998 May 01
19
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
DIP24: plastic dual in-line package; 24 leads (300 mil)
SOT222-1
1998 May 01
20
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
PLCC28: plastic leaded chip carrer; 28 leads; pedestal
SOT261-3
1998 May 01
21
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
SSOP24: plastic shrink small outline package; 24 leads; body width 5.3 mm
SOT340-1
1998 May 01
22
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
NOTES
1998 May 01
23
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family 2K/64 OTP/ROM, I2C, low pin count
83C751/87C751
Data sheet status
Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Production
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 05-98 Document order number: 9397 750 03845
Philips Semiconductors
1998 May 01 24


▲Up To Search▲   

 
Price & Availability of S83C751-5A28

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X