|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www..com LM2901H LOW POWER QUAD VOLTAGE COMPARATORS s WIDE SINGLE SUPPLY VOLTAGE RANGE OR DUAL SUPPLIES FOR ALL DEVICES: +2V TO +36V OR 1V TO 18V s VERY LOW SUPPLY CURRENT (1.1mA) INDEPENDENT OF SUPPLY VOLTAGE (1.4mW/comparator at +5V) s LOW INPUT BIAS CURRENT: 25nA TYP s LOW INPUT OFFSET CURRENT: 5nA TYP s INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GROUND SO-14 (Plastic Micropackage) s LOW OUTPUT SATURATION VOLTAGE: 250mV TYP. (IO = 4mA) s DIFFERENTIAL INPUT VOLTAGE RANGE EQUAL TO THE SUPPLY VOLTAGE s TTL, DTL, ECL, MOS, CMOS COMPATIBLE OUTPUTS DESCRIPTION This device consists of four independent precision voltage comparators. All these comparators were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible. These comparators also have a unique characteristic in that the input common-mode voltage range includes ground even though operated from a single power supply voltage. ORDER CODE Part Number JLM2901H-I6D1 LM2901HD Temperature Range -40C, +150C -40C, +150C Package Wafer * * SO14 Wafer form PIN CONNECTIONS (top view) Output 2 1 Output 1 2 V + CC 3 4 5 6 7 14 13 12 11 10 9 8 Output 3 Output 4 V CC Non-inverting input 4 Inverting input 4 Non-inverting input 3 Inverting input 3 Inverting input 1 Non-inverting input 1 Inverting input 2 Non-inverting input 2 D = Small Outline Package (SO) - also available in Tape & Reel (DT) September 2003 1/4 LM2901H SCHEMATIC DIAGRAM (1/4 LM2901) VCC+ 3.5A 100A 3.5A 100A Non-Inverting Input Vo VCCInverting Input VCC- VCC- PADS LOCATION Name OUT 1 OUT 2 OUT 3 OUT 4 Pad placement X Y 480 480 320 150 -150 -480 -480 -480 480 -150 150 300 480 480 -40 -340 -530 -530 -530 -530 -210 210 530 530 530 530 430 150 Pad dimension X 80 80 80 80 80 80 80 80 80 80 80 80 80 80 Y 80 80 80 80 80 80 80 80 80 80 80 80 80 80 Year Vcc + OUT2 0339 OUT1 Vcc - VCC+ E-(1) E+(1) y E- (1) E+ (4) E-(2) E+(2) E-(3) x E+ (1) E+ (4) E+(3) E-(4) E+(4) E- (2) E+ (2) E- (3) E+ (3) VCC OUT4 OUT3 PD98 The coordinate "Origin" is at the center of the die ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid VI ptot Toper Tstg Supply Voltage Differential Input Voltage Input Voltage Output Short-circuit to Ground 1) Power Dissipation at Tamb=+25C Storage Temperature Range 2) All dimensions are specified in micrometer (um) Parameter Value 18 to 36 36 -0.3 to +36 20 830 -40 to +150 -65 to +150 Unit V V V mA mW C C Operating Free-Air Temperature Range 1. Short-circuit from the output to Vcc+ can cause excessive heating and eventual destruction. The maximum output current is approximately 20mA, independent of the magnitude of V cc+ 2. Maximum power dissipation has been calculated with R thj-a= 150C/W for SO14 package, TA=+25C and TJ=+150C 2/4 LM2901H ELECTRICAL CHARACTERISTICS VCC+ = 5V, V CC- = GND, Tamb = 25C (unless otherwise specified) Symbol VI O Parameter Input Offset Voltage 1) Tamb = +25C Tmin Tamb Tmax. Input Offset Current Tamb = +25C Tmin Tamb Tmax. Input Bias Current (II+ or II-) 2) Tamb =+ 25C Tmin Tamb Tmax. Large Signal Voltage Gain (Vcc = 15V,RL=15k, Vo=1 to 11V) Supply Current (all comparators)) VCC = +5V, no load VCC = +30V, no load Input Common Mode Voltage Range (Vcc= 30V)3) Tamb = +25C Tmin Tamb Tmax. Differential Input Voltage4) Low Level Output Voltage Vid = -1V, Isink = 4mA Tamb = +25C Tmin Tamb Tmax High Level Output Current (VCC =Vo =30V, Vid = 1V) Tamb = +25C Tmin Tamb Tmax Output Sink Current (Vid = -1V,Vo = 1.5V) Tmin Tamb Tmax Small Signal Response Time5) (RL = 5.1k connected to VCC+ Large Signal Response Time6) TTL Input (Vref = +1.4 V, RL=5.1k to VCC+) Output Signal at 50% of final value Output Signal at 95% of final value 6 2 0 0 25 Min. Typ. 1 Max. 7 15 50 150 250 400 Unit mV IIO 5 nA IIB 25 nA AVD ICC 200 1.1 1.3 2 2.5 VCC+-1.5 VCC+- 2 VCC+ V/mV mA VICM VID V V VOL 250 400 700 mV IOH 0.1 1 16 nA A m s ISINK tRE 1.3 tREL 500 1 ns s 1. At output switch point, VO 1.4V, RS = 0 with VCC+ from 5V to 30V, and over the full input common-mode range (0V to VCC + -1.5V). 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference of input lines 3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ -1.5V, but either or both inputs can go to +30V without damage. 4. The response time specified is for a 100mV input step with 5mV overdrive. 5. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -0.3V (or 0.3V bellow the negative power supply, if used) 6. Maximum values are guaranteed by design. 3/4 LM2901H PACKAGE MECHANICAL DATA SO-14 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8 (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45 (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 PO13G Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners. (c) 2003 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Repubic - Finland - France - Germany Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain Sweden - Switzerland - United Kingdom - United States http://www.st.com 4/4 |
Price & Availability of LM2901H |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |