Part Number Hot Search : 
C4245 BUZ16 RXXP12D BUL62A MICON TA1286A PFZ180A 14014
Product Description
Full Text Search
 

To Download P1800ECLXXX Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 SIDACtor (R) Protection Thyristors
Baseband Protection (Voice-DS1)
SIDACtor(R) Series - TO-92
Description SIDACtor(R) Series TO-92 are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a robust through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals
Agency Agency File Number E133083
Does not degrade with use Applicable Global Standards TIA-968-A
Fails short circuit when surged in excess of ratings Low Capacitance
GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950
Pinout Designation
TIA-968-B ITU K.20/21 Enhanced Level* ITU K.20/21 Basic Level Pin 3 GR 1089 Inter-building*
* A/B-rated parts require series resistance
Pin 1 Schematic Symbol
Electrical Characteristics
VDRM @lDRM=5A V min P0080EALxxx P0300EALxxx P0640EALxxx P0720EALxxx P0900EALxxx P1100EALxxx P1300EALxxx P1500EALxxx P1800EALxxx P2300EALxxx P2600EALxxx P3100EALxxx P3500EALxxx P0080EA P0300EA P0640EA P0720EA P0900EA P1100EA P1300EA P1500EA P1800EA P2300EA P2600EA P3100EA P3500EA 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/s V max 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF min pF max 25 15 40 35 35 30 25 25 25 25 20 20 20 150 140 60 60 55 50 45 40 35 35 35 35 35
Part Number
Marking
mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800
2.2 2.2 2.2 2.2 2.2 2.2
Table continues on next page.
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
158 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
Baseband Protection (Voice-DS1)
Electrical Characteristics (continued)
VDRM @lDRM=5A V Min P0080EBLxxx P0300EBLxxx P0640EBLxxx P0720EBLxxx P0900EBLxxx P1100EBLxxx P1300EBLxxx P1500EBLxxx P1800EBLxxx P2300EBLxxx P2600EBLxxx P3100EBLxxx P3500EBLxxx P0080ECLxxx P0300ECLxxx P0640ECLxxx P0720ECLxxx P0900ECLxxx P1100ECLxxx P1300ECLxxx P1500ECLxxx P1800ECLXXX P2300ECLxxx P2600ECLxxx P3100ECLxxx P3500ECLxxx P0080EB P0300EB P0640EB P0720EB P0900EB P1100EB P1300EB P1500EB P1800EB P2300EB P2600EB P3100EB P3500EB P0080EC P0300EC P0640EC P0720EC P0900EC P1100EC P1300EC P1500EC P1800EC P2300EC P2600EC P3100EC P3500EC 6 25 58 65 75 90 120 140 170 190 220 275 320 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/s V Max 25 40 77 88 98 130 160 180 220 260 300 350 400 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS IT A Max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V Max 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF Min pF Max 25 15 40 35 35 30 25 25 25 25 20 20 20 35 25 55 50 45 45 40 35 35 30 30 30 25 150 140 60 75 70 70 60 55 50 50 45 45 40 260 250 155 150 140 115 105 95 90 80 80 70 65
Part Number
Marking
mA Min mA Max 50 50 150 150 150 150 150 150 150 150 150 150 150 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800
2.2
2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2
Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - xxx part number suffix: `AP' = Ammo Pack, `RP1' and `RP2' = Reel Pack, blank = Bulk Pack
Surge Ratings
Series IPP 0.2x310 1 0.5x700 2 A min A B C
Notes: 1 Current waveform in s 2 Voltage waveform in s
2x10 1 2x10 2 A min 150 250 500
8x20 1 1.2x50 2 A min 150 250 400
10x160 1 10x160 2 A min 90 150 200
10x560 1 10x560 2 A min 50 100 150
5x320 1 9x720 2 A min 75 100 200
10x360 1 10x360 2 A min 75 125 175
10x1000 1 10x1000 2 A min 45 80 100
5x310 1 10x700 2 A min 75 100 200
ITSM 50/60 Hz A min 20 25 30
di/dt A/s max 500 500 500
20 25 50
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40C < TJ <
Thermal Considerations
Package TO-92 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 90 Value Unit C C C/W
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
159 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
Baseband Protection (Voice-DS1)
V-I Characteristics
+I
tr x td Pulse Waveform
IPP - Peak Pulse Current - %IPP
IT IS IH IDRM -V VT VDRM VS +V
100
Peak Value
tr = rise time to peak value td = decay time to half value
Waveform = tr x td
50
Half Value
0 0
-I
tr
td t - Time (s)
Normalized VS Change vs. Junction Temperature
Normalized DC Holding Current vs. Case Temperature
2.0
Percent of VS Change - %
IH (TC = 25C)
14 12 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160
1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4
-40 -20 0 20 40 60 80 100 120 140 160
IH
25 C
25C
Junction Temperature (TJ) - C
Ratio of
Case Temperature (TC) - C
Soldering Parameters
Reflow Condition
- Temperature Min (Ts(min))
Pb-Free assembly (see Fig. 1)
Figure 1
TP
Ramp-up
tP
Critical Zone TL to TP
Pre Heat
- Temperature Max (Ts(max)) - Time (Min to Max) (ts)
60-180 secs. 3C/sec. Max. 3C/sec. Max. 60-150 secs.
TS(max) to TL - Ramp-up Rate Reflow
- Temperature (TL) (Liquidus) - Temperature (tL)
Temperature
Average ramp up rate (Liquidus Temp (TL) to peak)
TL TS(max)
Preheat
tL
Ramp-down
TS(min)
tS
Peak Temp (TP) Time within 5C of actual Peak Temp (tp) Ramp-down Rate Time 25C to Peak Temp (TP) Do not exceed 30 secs. Max. 6C/sec. Max. 8 min. Max.
25 time to peak temperature (t 25C to peak)
Time
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
160 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
Baseband Protection (Voice-DS1)
Physical Specifications
Environmental Specifications
High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102
Lead Material Terminal Finish Body Material
Copper Alloy 100% Matte-Tin Plated
Temp Cycling
UL recognized epoxy meeting flammability classification 94V-0
Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level
Part Numbering
Part Marking
P xxx 0 E x L xxx
TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE PACKING OPTIONS RoHS COMPLIANT IPP RATING
XXXXXXX XX
XXXXX
Part Marking Code Date Code
(Refer to Electrical Characteristics Table)
Packing Options
Package Type Description Packing Options Quantity Added Suffix RP1 TO-92 Tape and Reel Pack E TO-92 Ammo Pack TO-92 Bulk Pack 2000 RP2 AP N/A
Lead Spacing Industry Standard
0.1 inch (2.54mm) 0.2 inch (5.08mm) EIA-481-D EIA-468-B N/A
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
161 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
Baseband Protection (Voice-DS1)
Dimensions -- TO-92
Temperature Measurement Point
Ammo Pack Specification -- TO-92
Inches Min Max
0.196 0.105 0.145 0.096 0.186 0.096 0.019 0.017 0.60
Millimeters Min
4.47 12.70 2.41 3.81 3.43 2.23 4.47 2.23 0.33 0.33 3.68 2.44 4.73 2.44 0.48 0.43 1.52
Dimensions are in inches (and millimeters).
0.50 (12.7) 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0)
0.50 (12.7)
0.25 (6.35)
0.125 (3.2) MAX
Max
4.98 2.67
A N
A B D E
0.176 0.500 0.095 0.150 0.135 0.088 0.176 0.088 0.013 0.013
1.27 (32.2)
0.157 DIA (4.0) 0.20 (5.08) Flat down
B
G H J K L
Directio
n of Fe
ed
25 Devices per fold
MT1/PIN 1 E
MT2/PIN 3
M N
1.7 (43)
M L D J
H
G
K
All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) Mold flash shall not exceed 0.13 mm per side.
6.9 (175)
The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95.
1.7 (43) 12.9 (327)
Tape and Reel Specification -- TO-92
FLAT SIDE OF TO-92
Dimensions A B C
Inches Min N/A 4.016 3.386 0.795 1.181 0.496 0.498 0.090 0.182 N/A N/A 0.674 0.354 0.236 0.020 Max 14.173 N/A N/A N/A 1.968 0.504 0.502 0.110 0.244 1.673 1.270 0.763 0.370 N/A N/A
Millimeters Min N/A 102.0 86.0 20.2 30.0 12.60 12.65 2.29 4.63 N/A N/A 17 .12 8.25 6.00 0.50 Max 360.0 N/A N/A N/A 50.0 12.80 12.75 2.80 6.19 42.50 32.26 19.38 9.75 N/A N/A
A
D C B W1
D W1 P
ROUND SIDE OF TO-92
P0 F(for RP1) F(for RP2)
P
H1 H W W2
W3
W4
(RP1)
(RP2)
H H1 W W2 W3 W4
P0
F
F
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
162 Revised: February 22, 2011


▲Up To Search▲   

 
Price & Availability of P1800ECLXXX

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X