|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Model 1P610S Pico Xinger 10dB Directional Coupler Description The 1P610S Pico Xinger is a low profile, miniature 10dB directional coupler in an easy to use surface mount package designed for MMDS and WLAN applications. The 1P610S is for power and frequency detection as well as power injection. The 1P610S is an ideal solution for the ever-increasing demands of the wireless industry for smaller printed circuit boards and high performance. Parts have been subjected to rigorous qualification testing and units are 100% tested. They are manufactured using materials with x and y thermal expansion coefficients compatible with common substrates. Rev A * * * * * * * * * Features: ELECTRICAL SPECIFICATIONS** Frequency GHz 2.3 - 2.7 GHz MMDS and WLAN Very Low Loss High Directivity Surface Mountable Tape and Reel New Pico-Package 100% Tested Lead Free Mean Coupling dB Insertion Loss dB Max VSWR Max : 1 Freq. Sensitivity dB Max 2.3 - 2.7 Directivity dB Min 10 0.75 Power Handling Ave CW Watts 0.25 JC C / Watt 1.22 Operating Temp. C 0.2 20 20 44 -55 to +85 **Specification based on performance of unit properly installed on microstrip printed circuit boards with 50 nominal impedance. Specifications subject to change without notice. Top View (Near-side) .250.010 [6.350.25] .051.005 [1.290.13] Pin 2 Side View Bottom View (Far-side) 4X .020.004 [0.510.10] Pin 1 Orientation Marker Denotes Pin Location GND Pin 4 Pin 2 Pin 1 GND 4X .034.004 SQ [0.860.10] .200.010 [5.080.25] .120.004 [3.050.10] Denotes Array Number Pin 3 Pin 3 .170.004 [4.320.10] Pin 4 Dimensions are in Inches [Millimeters] 1P610S Rev A Mechanical Outline Tolerances are Non-Cumulative Available on Tape and Reel For Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Model 1P610S Rev A Typical Performance: 2.0 GHz. - 3.0 GHz. Coupling 1P610S -9.5 0 Return Loss 1P610S -10.0 -10 Return Loss (dB) Coupling (dB) -20 -10.5 -30 -11.0 -40 -11.5 2000 2200 2400 2600 2800 3000 -50 2000 2200 2400 2600 2800 3000 Frequency (MHz) Directivity 1P610S 0 0.00 Frequency (MHz) Transmission Loss 1P610S -10 Transmission Loss (dB) 2200 2400 2600 2800 3000 -0.20 Directivity (dB) -20 -0.40 -30 -0.60 -40 -0.80 -50 2000 -1.00 2000 2200 2400 2600 2800 3000 Frequency (MHz) Frequency (MHz) COUPLING Choice of a coupling value in an application normally depends on the power level of the main (sampled) line. For example, if the coupler is being used to monitor main line power, the coupling value is selected to provide sufficient power to the monitoring device and yet minimize system loss. Note that any coupler reduces power flowing in the main line by the amount coupled off; a 10dB coupler reduces main line power by 1 dB (10%) where a 20dB coupler reduces it by only 0.044dB (1%). Anaren uses mean coupling and frequency sensitivity with the coupling specification. The mean coupling value is arrived at by periodically sampling the coupling value over the specified band and averaging the readings. Frequency sensitivity is the peak to peak variation in coupling over the specified band. VSWR & DIRECTIVITY In directional couplers, directivity is specified in lieu of isolation. Directivity is a measure of how well the coupled power is isolated from reflections at the main line output port. For example, open or short circuiting the output port of a coupler with 20dB directivity would only affect the coupled output power by 1% and only 0.1% for 30dB directivity. High directivity is especially important if the coupler is being used to measure the VSWR of a device at its output port. In this application, accurate measurements of forward and reverse power are required. In theory, VSWR and directivity characteristics of a coupler are perfect; the input and output ports are perfectly matched and no power is coupled to the isolated port. In practice, factors associated with the design and manufacturing processes limit VSWR and directivity. The USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Available on Tape and Reel For Pick and Place Manufacturing. Model 1P610S Rev A VSWR & DIRECTIVITY (CONTINUED) internal meandering of the coupled lines and limitations of building perfect 50 transitions at the input and output ports of the device are the most significant factors against perfect VSWR and directivity. Typically, VSWR and directivity of 1.15:1 and 25 dB respectively are achieved in practice. INSERTION LOSS Coupler insertion loss is defined as the log of the input power divided by the sum of the power at the two output ports. In practice, typical loss is approximately 0.20 dB. Specification limits are somewhat higher due to imperfect test conditions; surface mount couplers must be tested in test fixtures that negatively affect results. PIN CONFIGURATION The 1P610S's have an orientation marker to denote either pin 1 or pin 2. When the input port is identified, the output, coupled and isolated ports are known automatically. For example, if the input port for a device was selected to be Pin 1, Pin 2 automatically becomes the output port, Pin 4 becomes the coupled port, and Pin 3 is the isolated port. Similarly, if Pin 2 was to be selected as the input port, the adjacent port on the long side (Pin 1) is the output port, the adjacent port on the short side (Pin 3) is the coupled port, and the opposite port (Pin 4) is the isolated port. Either port on the same side as the orientation marker can be selected as the input port, as shown in the table, which shows both pin configurations. The use of pin 1 or pin 2 as the input port ensures phase consistency as well as maximum power handling. MOUNTING For Xinger surface mount couplers to operate optimally, there must be 50 transmission lines leading to and from all of the RF ports. To ensure proper electrical and thermal performance, there must be a ground plane with 100% solder connection underneath the part. If either of these two conditions is not satisfied, insertion loss, coupling, VSWR and directivity may not meet published specifications. SUGGESTED FOOTPRINT To ensure proper electrical and thermal performance there must be a ground plane with 100% solder connection underneath the part Multiple plated thru holes to ground .170 [4.32] 4X .034 [0.86] 4X .063 SQ [1.60] 4X 50 Transmission Line .120 [3.05] Dimensions are in Inches [Millimeters] 1P610S Rev A Mounting Footprint Available on Tape and Reel For Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Model 1P610S Rev A PACKAGING Packaging follows EIA-481-2. Parts are oriented in tape as shown below. Xinger(R) Tape & Reel Diagram USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Available on Tape and Reel For Pick and Place Manufacturing. |
Price & Availability of 1P610S |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |