 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| EML4 / UML4N Transistors General purpose transistor (isolated transistor and diode) EML4 / UML4N 2SC5585 and RB521S-30 are housed independently in a EMT5 or UMT5 package. Applications DC / DC converter Motor driver Dimensions (Unit : mm) EMT5 1.6 0.5 1pin mark Features 1) Tr : Low VCE(sat) Di : Low VF 2) Small package 1.0 0.5 0.5 (5) (4) 1.6 1.2 (1) (2) (3) 0.22 0.13 Structure PNP Silicon epitaxial planar transistor Schottky barrier diode Each lead has same dimensions Abbreviated symbol : L4 ROHM : EMT5 The following characteristics apply to both Di1 and Tr2. Equivalent circuit (5) (4) UMT5 2.0 1.3 0.65 0.65 0.9 0.7 (5) (4) 1.25 1pin mark (1) (2) (3) 2.1 0.2 0.15 Di1 Tr2 Each lead has same dimensions (1) (2) (3) Abbreviated symbol : L4 ROHM : UMT5 EIAJ : SC-88A Packaging specifications Type Package Marking Code Basic ordering unit(pieces) EML4 EMT5 L4 T2R 8000 UML4N UMT5 L4 TR 3000 Rev.C 0.1Min. 1/4 EML4 / UML4N Transistors Absolute maximum ratings (Ta=25C) Di1 Parameter Symbol IO Average rectified forward current IFSM Forward current surge peak (60HZ, 1) VR Reverse voltage (DC) Tj Junction temperature Limits 200 1 30 125 Unit mA A V C Tr2 Parameter Collector-base voltage Collector-emitter voltage Emitter-base voltage Collector current Power dissipation Junction temperature Each terminal mounted on a recommended. Symbol VCBO VCEO VEBO IC ICP Pd Tj Limits -15 -12 -6 -500 -1 120 150 Unit V V V mA A mW C Di1 / DTr2 Parameter Power dissipation Storage temperature Each terminal mounted on a recommended. Symbol Pd Tstg Limits 150 -55 to +125 Unit mW C Electrical characteristics (Ta=25C) Di1 Parameter Forward voltage Reverse current Symbol VF IR Min. - - Typ. 0.40 4.0 Max. 0.50 30 Unit V A IF=200mA VR=10V Conditions Tr2 Parameter Collector-emitter breakdown voltage Collector-base breakdown voltage Emitter-base breakdown voltage Collector cut-off current Emitter cut-off current Collector-emitter saturation voltage DC current gain Transition frequency Collector output capacitance Symbol BVCEO BVCBO BVEBO ICBO IEBO VCE(sat) hFE fT Cob Min. -12 -15 -6 - - - 270 - - Typ. - - - - - -100 - 260 6.5 Max. - - - -100 -100 -250 680 - - Unit V V V nA nA mV - MHz pF Conditions IC=-1mA IC=-10A IE=-10A VCB=-15V VEB=-6V IC=-200mA, IB=-10mA VCE=-2V, IC=-10mA VCE=-2V, IE=10mA, f=100MHz VCB=-10V, IE=0mA, f=1MHz Rev.C 2/4 EML4 / UML4N Transistors Electrical characteristic curves Di1 Tr2 1000 COLLECTOR CURRENT : IC (mA) VCE=2V Pulsed DC CURRENT GAIN : hFE 1000 Ta=125C Ta=25C Ta=-40C COLLECTOR SATURATION VOLTAGE : VCE(sat) (mV) 1000 Ta=25C Pulsed VCE=2V Pulsed 100 100 100 IC/IB=50 IC/IB=20 5C C Ta=25 Ta= -40 Ta=12 C 10 10 10 IC/IB=10 1 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1 1 10 100 1000 1 1 10 100 1000 BASE TO EMITTER VOLTAGE : VBE (V) COLLECTOR CURRENT : IC (mA) COLLECTOR CURRENT : IC (mA) Fig.3 Grounded emitter propagation characteristics Fig.4 DC current gain vs. collector current Fig.5 Collector-emitter saturation voltage vs. collector current ( ) COLLECTOR SATURATION VOLTAGE : VCE (sat) (mV) BASER SATURATION VOLTAGE : VBE (sat) (mV) 1000 IC/IB=20 Pulsed 10000 100 Ta=25C Ta=125C 1000 Ta=25C Ta=-40C TRANSITION FREQUENCY : fT (MHz) IC/IB=20 Pulsed 1000 VCE=2V Ta=25C Pulsed 100 Ta=125C Ta=-40C 10 100 10 1 1 10 100 1000 10 1 10 100 1000 1 1 10 100 1000 COLLECTOR CURRENT : IC (mA) COLLECTOR CURRENT : IC (mA) EMITTER CURRENT : IE (mA) Fig.6 Collector-emitter saturation voltage Fig.7 Base-emitter saturation voltage Fig.8 Gain bandwidth product vs. collector current ( ) vs. collector current vs. emitter current Rev.C 2/4 EML4 / UML4N Transistors EMITTER INPUT CAPACITANCE : Cib (pF) COLLECTOR OUTPUT CAPACITANCE : Cob (pF) 1000 TRANSITION FREQUENCY : IC (A) IE=0A f=1MHz Ta=25C 100 10 Ta=25C Single Pulsed 1 10ms 100ms DC 1ms Cib 10 Cob 0.1 0.01 1 0.1 1 10 100 0.001 0.01 0.1 1 10 100 EMITTER TO BASE VOLTAGE : VEB(V) EMITTER CURRENT : VCE (V) Fig.9 Collector output capacitance vs. collector-base voltage Emitter input capacitance vs. emitter-base voltage Fig.10 Safe operation area Rev.C 3/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright (c) 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0 |
Price & Availability of UML4N1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |