View TISP6NTP2A_4965824.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

oH
S
CO
M
PL
IA
TISP6NTP2A QUAD FORWARD-CONDUCTING BUFFERED P-GATE THYRISTORS
*R
NT
TISP6NTP2A Programmable Protector
Independent Overvoltage Protection for Two SLICs in Short Loop Applications: - Wide 0 to -90 V Programming Range - Low 5 mA max. Gate Triggering Current - High 150 mA min. (85 C) Holding Current - Specified 1.2/50 & 0.5/700 Limiting Voltage - Full -40 C to 85 C Temperature Range Rated for Common Impulse Waveforms
D Package (Top View)
K1 G1,G2 G3,G4 K3
1 2 3 4
8 7 6 5
K2 A A K4
MDRXAM
Voltage Impulse Form 10/1000 s 10/700 s 1.2/50 s 2/10 s
Current Impulse Shape 10/1000 s 5/310 s 8/20 s 2/10 s
ITSP A 20 25 75 85
Device Symbol
K1
.............................................. UL Recognized Component
G1,G2
Description
The TISP6NTP2A has been designed for short loop systems such as: - WILL (Wireless In the Local Loop) - FITL (Fibre In The Loop) - DAML (Digital Added Main Line, Pair Gain) - SOHO (Small Office Home Office) - ISDN-TA (Integrated Services Digital Network Terminal Adaptors)
K2 A A K3
Typical TISP6NTP2A Router Application
TERMINAL ADAPTOR SLIC 1 PROCESSOR SLIC 2 TISP6 NTP2A POTS 2 POTS 1
K4
SDRXAI
G3,G4
LINE
TRANSCEIVER
TRANSCEIVER
LAN
How To Order
Device TISP6NTP2A Package Carrier Order As TISP6NTP2ADR-S
D, Small-Outline Tape and Reel
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
TISP6NTP2A Programmable Protector
Description (continued)
These systems often have the need to source two POTS (Plain Old Telephone Service) lines, one for a telephone and the other for a facsimile machine. In a single surface mount package, the TISP6NTP2A protects the two POTS line SLICs (Subscriber Line Interface Circuits) against overvoltages caused by lightning, a.c. power contact and induction. The TISP6NTP2A has an array of four buffered P-gate forward conducting thyristors with twin commoned gates and a common anode connection. Each thyristor cathode has a separate terminal connection. An antiparallel anode-cathode diode is connected across each thyristor. The buffer transistors reduce the gate supply current. In use, the cathodes of an TISP6NTP2A thyristor are connected to the four conductors of two POTS lines (see applications information). Each gate is connected to the appropriate negative voltage battery feed of the SLIC driving that line pair. By having separate gates, each SLIC can be protected at a voltage level related to the negative supply voltage of that individual SLIC. The anode of the TISP6NTP2A is connected to the SLIC common. Positive overvoltages are clipped to common by forward conduction of the TISP6NTP2A antiparallel diode. Negative overvoltages are initially clipped close to the SLIC negative supply by emitter follower action of the TISP6NTP2A buffer transistor. If sufficient clipping current flows, the TISP6NTP2A thyristor will regenerate and switch into a low voltage on-state condition. As the overvoltage subsides, the high holding current of the TISP6NTP2A prevents d.c. latchup.
Absolute Maximum Ratings, TA = 25 C (Unless Otherwise Noted)
Rating Repetitive peak off-state voltage, IG = 0,- 40 C TJ 85 C Repetitive peak gate-cathode voltage, VKA = 0, - 40 C TJ 85 C Non-repetitive peak on-state pulse current, -40 C TJ 85 C, (see Notes 1 and 2) 10/1000 s (Bellcore GR-1089-CORE, Issue 1, November 1994, Section 4) 0.2/310 s (I3124, open-circuit voltage wave shape 0.5/700 s) 5/310 s (ITU-T K.20 & K.21, open-circuit voltage wave shape 10/700 s) 8/20 s (IEC 61000-4-5:1995, open-circuit voltage wave shape 1.2/50 s) 2/10 s (Bellcore GR-1089-CORE, Issue 1, November 1994, Section 4) Non-repetitive peak on-state current, 50/60 Hz, -40 C TJ 85 C, (see Notes 1 and 2) 100 ms 1s 5s 300 s 900 s Non-repetitive peak gate current, 1/2 s pulse, cathodes commoned (see Note 1) Operating free-air temperature range Junction temperature Storage temperature range ITSM 7 2.7 1.5 0.45 0.43 25 -40 to +85 -40 to +150 -65 to +150 A ITSP 20 25 25 75 85 A Symbol VDRM VGKRM Value -100 -90 Unit V V
IGSM TA TJ Tstg
A C C C
NOTES: 1. Initially, the protector must be in thermal equilibrium with -40 C TJ 85 C. The surge may be repeated after the device returns to its initial conditions. 2. These non-repetitive rated currents are peak values for either polarity. The rated current values may be applied to any cathodeanode terminal pair. Additionally, all cathode-anode terminal pairs may have their rated current values applied simultaneously (in this case the anode terminal current will be four times the rated current value of an individual terminal pair). Above 85 C, derate linearly to zero at 150 C lead temperature.
JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
TISP6NTP2A Programmable Protector
Recommended Operating Conditions
Min. CG Gate decoupling capacitor Series resistor for GR-1089-CORE first-level surge survival Series resistor for ITU-T recommendation K.20 Series resistor for ITU-T recommendation K.21 Series resistor for IEC 61000-4-5:1995, class 5, 1.2/50 or 10/700 100 40 12 20 4 Typ. 220 Max. Unit nF
R1, R2
Electrical Characteristics for any Section, TA = 25 C (Unless Otherwise Noted)
Parameter ID Off-state current VD = VDRM, IG = 0 Test Conditions TJ = 25 C TJ = 85 C Min. Typ. Max. -5 -50 -70 V -70 2 3 5 15 V 15 2 4 -150 TJ = 25 C TJ = 85 C -5 -50 -1 s mA A A mA s V Unit A A
V(BO) t(BR) VF
Breakover voltage Breakdown time Forward voltage Peak forward recovery voltage Forward recovery time Holding current Gate reverse current Gate reverse current, on state Gate reverse current, forward conducting state Gate trigger current Gate trigger voltage Anode-cathode offstate capacitance
IT = -20 A, IEC 61000-4-5:1995 combination impulse generator, VGG = -50 V IT = -18 A, I3124 impulse generator, VGG = -50 V IT = -18 A, I3124 impulse generator, V(BR) < -50 V IF = 0.6 A, tw = 500 s, VGG = -50 V IF = 18 A, tw = 500 s, VGG = -50 V IF = 20 A, IEC 61000-4-5:1995 combination impulse generator, VGG = -50 V IF = 18 A, I3124 impulse generator, VGG = -50 V IF = 18 A, I3124 impulse generator, VGG = -50 V IT = -1 A, di/dt = 1A/ms, VGG = -50 V, TJ = 85 C VGG = VGKRM, VAK = 0 IT = -0.6 A, tw = 500 s, VGG = -50 V VF > 10 V VF > 5 V
VFRM
tFR IH IGKS IGAT
IGAF IGT VGT CAK
IF = 0.6 A, tw = 500 s, VGG = -50 V IT = -5 A, tp(g) 20 s, VGG = -50 V IT = -5 A, tp(g) 20 s, VGG = -50 V f = 1 MHz, Vd = 1 V, IG = 0, (see Note 3) VD = -3 V VD = -50 V
-40 5 2.5 100 60
mA mA V pF pF
NOTE
3: These capacitance measurements employ a three terminal capacitance bridge incorporating a guard circuit. The unmeasured device terminals are a.c. connected to the guard terminal of the bridge.
Thermal Characteristics
Parameter RJA Junction to free air thermal resistance Test Conditions Ptot = 0.52 W, TA = 85 C, 5 cm2, FR4 PCB Min. Typ. Max. 160 Unit C/W
JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
TISP6NTP2A Programmable Protector
Parameter Measurement Information
PR IN C IPA L TER MIN A L V-I C H AR A C TER ISTIC +i I FSP (= |I TSP |) Q uadran t I Forw ard C onduc tion C haracteristic G AT E TR AN SFER C H AR A C TER ISTIC +i K
I FSM (= |I TSM |) IF VF V G K (B O ) V GG VD ID IG T +v -i G IG A F +i G IF
-v
I (B O ) IS
IH VT IT I TSM IG IG A T IT
V (BO)
VS
Q uadran t III Sw itchin g C haracteristic I TSP -i
P M6X AIA
IK -i K
Figure 1. Principal Terminal And Gate Transfer Characteristics
JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
TISP6NTP2A Programmable Protector
APPLICATIONS INFORMATION
Operation of Gated Protectors
Figure 2 and Figure 3 show how the TISP6NTP2A limits overvoltages. The TISP6NTP2A thyristor sections limit negative overvoltages and the diode sections limit positive overvoltages.
SLIC PROTECTOR R1A R1A SLIC PROTECTOR
SLIC 1
SLIC 1
R1B VBAT1
R1B VBAT1
C1 100 nF TISP6NTP2A R2A
0V
C1 100 nF TISP6NTP2A R2A
0V
SLIC 2
SLIC 2
IK R2B VBAT2 IG R2B
IF VBAT2 IG
AI6XBN
C2 100 nF
0V
AI6XBO
C2 100 nF
0V
Figure 2. Negative Overvoltage Condition
Figure 3. Positive Overvoltage Condition
Negative overvoltages (Figure 2) are initially clipped close to the SLIC negative supply rail value (VBAT) by the conduction of the transistor base-emitter and the thyristor gate-cathode junctions. If sufficient current is available from the overvoltage, then the thyristor will crowbar into a low voltage ground referenced on-state condition. As the overvoltage subsides, the high holding current of the crowbar thyristor prevents d.c. latchup. The common gate of each thyristor pair is connected the appropriate SLIC battery feed voltage (VBAT1 or VBAT2). The negative protection voltage, V(BO), will be the sum of the gate supply (VBAT) and the peak gate (terminal)-cathode voltage (VGT ). Under a.c. overvoltage conditions VGT will be less than 2.5 V. The integrated transistor buffer in the TISP6NTP2A greatly reduces protectors source and sink current loading on the VBAT supply. Without the transistor, the thyristor gate current would charge the VBAT supply. An electronic power supply is not usually designed to be charged like a battery. As a result, the electronic supply would switch off and the thyristor gate current would provide the SLIC supply current. Normally the SLIC current would be less than the gate current, which would cause the supply voltage to increase and destroy the SLIC by a supply overvoltage. The integrated transistor buffer removes this problem. Fast rising impulses will cause short term overshoots in gate-cathode voltage. The negative protection voltage under impulse conditions will also be increased if there is a long connection between the gate decoupling capacitor and the gate terminal. During the initial rise of a fast impulse, the gate current (IG ) is the same as the cathode current (IK ). Rates of 60 A/s can cause inductive voltages of 0.6 V in 2.5 cm of printed wiring track. To minimize this inductive voltage increase of protection voltage, the length of the capacitor to gate terminal tracking should be minimized.
JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
TISP6NTP2A Programmable Protector
APPLICATIONS INFORMATION
Operation of Gated Protectors (continued)
Positive overvoltages (Figure 3) are clipped to ground by forward conduction of the diode section in the TISP6NTP2A. Fast rising impulses will cause short term overshoots in forward voltage (V FRM).
Central Office Application to Bellcore GR-1089-Core Issue 1
The most stressful impulse for first-level surge testing (section 4.5.7) is the 1000 V, 10/1000 impulse. To limit the circuit current to the TISP6NTP2A rating of 20 A requires the total circuit resistance to be 1000/20 = 50 . Subtracting the generator fictive source impedance of 10 gives 40 as the required series resistor value for the TISP6NTP2A (R1A, R1B, R2A and R2B). The various first level impulse current levels are shown in table 1. The maximum 1.2/50 and 2/10 current levels of 56 A are below the TISP6NTP2A ratings of 60 A and 85 A. In table 1, the designation 2x20 means that each conductor has a simultaneous peak current of 20 A and 2x20 = 40 A flows in the anode (ground) connection.
Ta ble 1. First-level Surge Currents
Open-circuit Voltage V 2500 2500 Short-c ircuit Current A 500 500 Generator Resistance 5 2 + 3/Wire Both Single 10/1000 1000 100 10 Both 25 2x20 28.5 50 2x53 20 Total Series Resistance 22.5 45 IT A 2x56 56
Waveshape
Wires Tested
2/10 1.2/50 8/20
Both Single
Central Office Application to ITU-T Recommendation K.20
The test level of 1000 V 10/700 delivers a peak short-circuit current level of 25 A, which is equal to the TISP6NTP2A rated value. A series resistor (R1A, R1B, R2A and R2B) is required to ensure coordinated operation with the primary protector at the 4000 V test level. The resistor value will be set by the sparkover voltage of the primary protector. A sparkover voltage of 300 V will give a 300/25 = 12 series resistor.
Local Subscribers Line Equipment to ITU-T Recommendation K.21
The test level of 1500 V 10/700 delivers a peak short-circuit current level of 37.5 A. To limit the circuit current to the TISP6NTP2A rating of 25 A requires the total circuit resistance to be 1500/25 = 60 . Subtracting the generator fictive source impedance of 40 gives 20 as the required series resistor value for the TISP6NTP2A. Even at the 1500 V test level, this resistor develops 25x20 = 500 V, which should ensure the coordination with the primary protector sparkover.
JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
TISP6NTP2A Programmable Protector
APPLICATIONS INFORMATION
Indoor POTS Lines to ITU-T Recommendation K.21. K.22 and IEC 61000-4-5: 1995
Internal POTS lines from WILL and ISDN-TA equipment are in a relatively unexposed environment. If these lines are galvanically isolated (floating), the return path for any induced surges can only be through equipment capacitance or insulation breakdown. The most stressful condition would be when the POTS lines are not galvanically isolated. Such a case is when an ISDN-TA has a common connection between the incoming ISDN line and the internal POTS lines. The ISDN line is likely to be ground referenced and may have primary protection at the subscriber connection. If the primary protection operates, it provides a direct return to ground. ITU-T recommendation K.22 for a floating 4-conductor T/S bus uses a 1 kV 1.2/50 or 2/10 impulse, capacitively coupled via 8 nF to the bus conductors. Very little circulating current is likely to flow during K.22 testing. If the T/S bus has a ground return, then the testing changes to ITU-T recommendation K.21. The required series resistor values for K.21 and the TISP6NTP2A have been calculated earlier. In IEC 61000-4-5: 1995 the highest specified test level is class 5. For unshielded symmetrically operated lines, class 5 testing uses a 4000 V combination wave (1.2/50, 8/20) generator to apply a simultaneous impulse to all conductors. For the four conductors of the two POTS lines, the currents are equalized by the use of specified 160 feed resistors. As the generator fictive source impedance is 2 , the peak current in each conductor is 4000/(2x4 + 160) = 24 A. This is less than the 60 A TISP6NTP2A rating. If the lines are long and exit the building, testing is done with a 10/700 generator. In this case the feed resistors are 100 and the fictive impedance is 15 . The peak current in each conductor will be 4000/(15x4 + 100) = 25 A. This value is the same as the TISP6NTP2A rating. As the equipment connected to the POTS line may have uncoordinated protection, it is desirable to provided the ring-tip pair current sharing to the TISP6NTP2A by series resistors (R1A, R1B, R2A and R2B). A value of 4 should be sufficient to ensure sharing.
"TISP" is a trademark of Bourns, Ltd., a Bourns Company, and is Registered in U.S. Patent and Trademark Office. "Bourns" is a registered trademark of Bourns, Inc. in the U.S. and other countries.
JUNE 1998 - REVISED JULY 2008 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.

▲Up To Search▲

Price & Availability of TISP6NTP2A

	To Download TISP6NTP2A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .