![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 1/7 APPLICATIONS o Highside switch for industrial applications, such as relays, inductive proximity sensors and light barriers FEATURES o 36 V highside switch/level shifter o p-channel output driver without charge pump for short activation time o Decoupling of input and output reference voltages (SOT23-6L) permits control by 5V logic o 200 mA of output current o Short-circuit protected o Output with an active freewheeling circuit o On-chip overtemperature protection with hysteresis o 4 to 36 V input voltage range o Input with hysteresis o 3-pin configuration possible o Wide temperature range of -40 to 120 C o Package option: (SOT223-4L, SC59-3L, DFN, CSP) PACKAGES SOT23-6L BLOCK DIAGRAM 3-pin configuration PI IC-DP INPUT INTERFACE HIGH-SIDE SWITCH VP & Tj < 120C temperature monitor 200 mA 3.5 V NI DP Copyright (c) 2007 iC-Haus http://www.ichaus.com IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 2/7 DESCRIPTION IC-DP is a monolithic highside switch for ohmic, inductive and capacitive loads. Designed for a wide input voltage range of 4 to 36 V, it is capable of supplying a minimum output current of 200 mA. The output acts as a current source with a low saturation voltage; protection against shortcircuiting is provided by the device shutting down with excessive temperature. The chip is activated when the input voltage threshold V(PI)-V(NI) of typically 3.5 V is exceeded. When used as a 4-pin element (with the SOT23-6L package only), the input (PI, NI) and output (DP, VP) reference voltages are decoupled. The maximum permissive voltage difference between VP and PI is 36 V. PACKAGES SOT23-6L (JEDEC) PIN CONFIGURATION SOT23-6L (JEDEC), 1.6 mm (top view) 6 5 4 PIN FUNCTIONS No. Name Function 1 2 3 4 5 6 NI PI DP VP n.c. n.c. Negative Input Positive Input Output Supply 1 2 3 SOT223-4L, SC59-3L , DFN and CSP packages are available on request. IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 3/7 ABSOLUTE MAXIMUM RATINGS Beyond these values damage may occur; device operation is not guaranteed. Absolute Maximum Ratings are no Operating Conditions. Integrated circuits with system interfaces, e.g. via cable accessible pins (I/O pins, line drivers) are per principle endangered by injected interferences, which may compromise the function or durability. The robustness of the devices has to be verified by the user during system development with regards to applying standards and ensured where necessary by additional protective circuitry. By the manufacturer suggested protective circuitry is for information only and given without responsibility and has to be verified within the actual system with respect to actual interferences. Item No. Symbol Parameter VP, PI Input Voltage with reference to NI DP Output Current PI Input Current NI Input Current ESD Susceptibility Max. Junction Temperature Storage Temperature Range Inductive load switch-off energy dissipation temperature monitor not active, Tj < Ton HBM 100 pF/ discharged throught 1.5 k -40 -40 -10 2 150 150 5 Conditions V()=V(VP)-V(NI) bzw. V()=V(PI)-V(NI) Fig. Min. -0.3 -40 -300 10 Max. 40 0.3 V V mA mA mA kV C C mJ Unit G001 V() G002 V(DP) G003 I(DP) G004 I(PI) G005 I(NI) G006 Vd() G007 Tj G008 Ts G009 Eas DP Output Voltage with reference to VP no free wheeling THERMAL DATA Operating Conditions: V(PI) = 4...36 V, unless otherwise stated Item No. T01 Symbol Ta Parameter Ambient Temperature Range Conditions Fig. Min. -40 Typ. Max. 120 C Unit All voltages are referenced to ground (NI) unless otherwise stated. All currents into the device pins are positive; all currents out of the device pins are negative. IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 4/7 ELECTRICAL CHARACTERISTICS Operating Conditions: V(PI) = 4...36 V, Tj = -40...120 C, unless otherwise stated Item No. 001 002 Symbol Parameter Conditions Tj C Fig. Min. 4 Typ. Max. 36 V Unit Total Device V() I(PI) VP, PI Supply Voltage PI Supply Current V()= V(VP)-V(NI) bzw. V()=V(PI)V(NI) No load; V(PI) - V(NI) > V(PI)on V(PI) - V(NI) < V(PI)off No load; V(PI) - V(NI) > V(PI)on V(PI) - V(NI) < V(PI)off No load; V(PI) - V(NI) > V(PI)on V(PI) - V(NI) < V(PI)off V(PI) - V(NI) < V(PI)off, V(DP) = 0..V(VP) Vc(DP)lo = V(DP) - V(VP), I(DP) = -10 mA Vc(DP)hi = V(DP) - V(VP), I(DP) = 10 mA Vc()hi = V() - V(NI), I() = 4 mA V(PI)on < V(PI) - V(NI) < 48 V, V(Rload) = 48 V, Rload = 360 , I(DP) = 0 -90 mA V(PI) - V(NI) < V(PI)off, V(Rload) = 36 V, Rload = 360 , I(DP) = -100 -10 mA DP = hi, with reference to VP I(DP) = -200 mA, I(DP) = -50 mA V(VP) - V(DP) = 1 V...VB, DP = hi -40 27 120 0 0 80 0 -850 -2000 -100 -70 0.3 37 1 40 -45 300 190 680 2000 -130 0 100 -40 1 A A A A A A A V V V 003 I(VP) VP Supply Current 004 I(NI) NI Input Current 005 006 007 008 009 Ilk(DP) Vc(DP)lo Vc(DP)hi Vc()hi tpiohi DP Output Leakage Current DP Clamp Voltage low DP Clamp Voltage high PI, VP Clamp Voltage high Activation Delay NI DP 25 s 010 tpiolo Deactivation Delay NI DP 1 15 s Highside Output DP 101 Vs(DP) Output Saturation Voltage -600 -150 -800 -400 50 -200 -200 -200 mV mV mA mA mA V/s 102 Isc(DP) Output Short-Circuit Current 103 SR(DP)on Slew Rate, V(DP) VP V(PI) - V(NI) > V(PI)on, V(Rload) = 36 V, Rload = 360 , V(VP) - V(DP) = 32.4 3.6 V V(PI) - V(NI) < V(PI)off, V(Rload) = 36 V, Rload = 360 , V(VP) - V(DP) = 3.6 32.4 V I(DP) = -200 mA, with reference to VP -70 104 SR(DP)off Slew Rate, V(DP) V(NI) 20 V/s 105 Vfw(DP) Freewheeling Voltage -45 -40 V Temperature Monitor 201 202 203 301 302 303 Toff Ton Thys V(PI)on V(PI)off V(PI)hys Thermal Shutdown Threshold Thermal Release Threshold Thermal Shutdown Hysteresis Power-On Threshold Voltage Power-Off Threshold Voltage Hysteresis Decreasing temperature Thys = Toff - Ton V(PI) - V(NI) V(PI)-V(NI), decreasing voltage V(PI)hys = V(PI)on - V(PI)off 2.7 2.3 170 380 120 110 15 4.1 3.7 590 150 135 C C C V V mV Input Threshold IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 5/7 ELECTRICAL CHARACTERISTIC: DIAGRAMS Simulation Data (current consumption without load; leakage currents not included) 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 V(PI)-V(NI) [V] -200 -400 -600 -800 -400 -800 -1200 -1600 V(PI)-V(NI) [V] I(NI) [A] I(NI) [A] Figure 1: NI input current, no load 0 2 4 6 8 10 12 14 -200 -150 -100 -50 Figure 2: NI input current, I(DP) = -5 mA I(PI) [A] V(PI)-V(NI) [V] -200 -400 -600 -800 V(PI)-V(NI) [V] I(NI) [A] 0 2 4 6 8 10 12 14 Figure 3: NI input current, I(DP) = -100 mA Figure 4: PI input current, load independent 0 10 20 30 40 I(VP) [A] 600 -100 -200 -300 200 -400 V(PI)-V(NI) [V] 400 V(PI)-V(NI) [V] 0 2 4 6 8 10 12 14 -500 Isc(DP) [A] Figure 5: VP supply current, no load 0 2 Figure 6: DP short-circuit output current 36 4 35 V(VP)-V(DP) [V] 200 400 600 800 I(DP) [mA] Figure 7: DP output characteristic IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 6/7 APPLICATION NOTES Example application circuits for SOT23-6L package 36V I PI IC-DP 10k 10k VP PI IC-DP VP 36V I NI SOT23-6L DP Rload NI SOT23-6L DP Rload Figure 8: 36 V supply, NPN input control 36V 5V Figure 9: 36 V supply, PNP input control 36V 12V I V PI IC-DP VP PI IC-DP 10k VP 0V NI SOT23-6L DP Rload NI SOT23-6L DP Rload Figure 10: 5 V C operating at 5 to 0 V input control, 36 V output supply 36V 12V Figure 11: 12 V PNP input control, 36 V output supply PI IC-DP 10k VP NI I SOT23-6L DP Rload Figure 12: 12 V NPN input control, 36 V output supply This specification is for a newly developed product. iC-Haus therefore reserves the right to change or update, without notice, any information contained herein, design and specification; and to discontinue or limit production or distribution of any product versions. Please contact iC-Haus to ascertain the current data. Copying - even as an excerpt - is only permitted with iC-Haus approval in writing and precise reference to source. iC-Haus does not warrant the accuracy, completeness or timeliness of the specification on this site and does not assume liability for any errors or omissions in the materials. The data specified is intended solely for the purpose of product description. No representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or areas of applications of the product. iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade mark rights of a third party resulting from processing or handling of the product and/or any other use of the product. IC-DP HIGHSIDE SWITCH y inar im prel Rev B1, Page 7/7 ORDERING INFORMATION Type IC-DP Package SOT23-6L (JEDEC) Order Designation IC-DP SOT23-6L For technical support, information about prices and terms of delivery please contact: iC-Haus GmbH Am Kuemmerling 18 D-55294 Bodenheim GERMANY Tel.: +49 (61 35) 92 92-0 Fax: +49 (61 35) 92 92-192 Web: http://www.ichaus.com E-Mail: sales@ichaus.com Appointed local distributors: http://www.ichaus.de/support_distributors.php |
Price & Availability of IC-DP
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |