View HT95A20P_4935402.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HT95LXXX LCD Type Phone 8-Bit MCU
Features
* Provide MASK type and OTP type version * Operating voltage range: 2.4V~5.5V * Program ROM - HT95L400/40P: 16K16 bits - HT95L300/30P: 8K16 bits - HT95L200/20P: 8K16 bits - HT95L100/10P: 4K16 bits - HT95L000/00P: 4K16 bits * Data RAM - HT95L400/40P: 28808 bits - HT95L300/30P: 21128 bits - HT95L200/20P: 11528 bits - HT95L100/10P: 11528 bits - HT95L000/00P: 3848 bits * Bidirectional I/O lines - HT95L400/40P: 40~28 - HT95L300/30P: 28~16 - HT95L200/20P: 28~20 - HT95L100/10P: 20~16 - HT95L000/00P: 18~14 * Programmable frequency divider (PFD)
Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P
* Dual system clock: 32768Hz, 3.58MHz * Four operating modes: Idle mode, Sleep mode,
Green mode and Normal mode
* Up to 1.117ms instruction cycle with 3.58MHz system
clock
* All instructions in one or two machine cycles * Built-in 3.58MHz DTMF Generator * Built-in dialer I/O * Built-in low battery detector
Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P
* LCD driver - LCD contrast can be adjusted by software or exter-
I/O lines I/O lines I/O lines I/O lines I/O lines
nal resistor
- Support two LCD frame frequency 64Hz, 128Hz - Support 16 or 8 common driver pins - Some segments or commons can option to
* 16-bit table read instructions * Subroutine nesting - HT95L400/40P: 12 levels - HT95L300/30P: 8 levels - HT95L200/20P: 8 levels - HT95L100/10P: 8 levels - HT95L000/00P: 4 levels * Timer - Two 16-bit programmable Timer/Event Counter - Real time clock (RTC) - Watchdog Timer (WDT)
bidirectional I/O lines
- HT95L400/40P: 48 seg.16 com. - HT95L300/30P: 48 seg.16 com. - HT95L200/20P: 24 seg.16 com. - HT95L100/10P: 20 seg.8 com. - HT95L000/00P: 16 seg.8 com. * HT95L400/40P: 128-pin QFP package
HT95L300/30P: 100-pin QFP package HT95L200/20P: 100-pin QFP package HT95L100/10P: 64-pin QFP package HT95L000/00P: 56-pin SSOP package
Applications
* Deluxe Feature Phone * Caller ID Phone * Cordless Phone * Fax and answering machines * Other communication system
General Description
The HT95LXXX family MCU are 8-bit high performance RISC-like microcontrollers with built-in DTMF generator and dialer I/O which provide MCU dialer implementation or system control features for telecom product applications. The phone controller has a built-in program ROM, data RAM, LCD driver and I/O lines for high end products design. In addition, for power management purpose, it has a built-in frequency up conversion circuit (32768Hz to 3.58MHz) which provides dual system clock and four types of operation modes. For example, it can operate with low speed system clock rate of 32768Hz in green mode with little power consumption. It can also operate with high speed system clock rate of 3.58MHz in normal mode for high performance operation. To ensure smooth dialer function and to avoid MCU shut-down in extreme low voltage situation, the dialer I/O circuit is built-in to generate hardware dialer signals such as on-hook, hold-line and hand-free. Built-in real time clock and programmable frequency divider are provided for additional fancy features in product developments. The device is best suited for feature phone products that comply with versatile dialer specification requirements of different areas or countries.
Rev. 1.20
1
May 26, 2004
HT95LXXX
Selection Table
Part No. HT95A100 HT95A10P HT95A200 HT95A20P HT95A300 HT95A30P HT95A400 HT95A40P HT95L000 HT95L00P HT95L100 HT95L10P HT95L200 HT95L20P HT95L300 HT95L30P HT95L400 HT95L40P HT95C200 HT95C20P HT95C300 HT95C30P HT95C400 HT95C40P Operating Program Data Normal Dialer Voltage Memory Memory I/O I/O 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 2.4V~5.5V 4K16 4K16 8K16 16K16 4K16 4K16 8K16 8K16 16K16 8K16 8K16 16K16 3848 11528 21128 28808 3848 11528 11528 21128 28808 11528 21128 28808 20 28 28 44 14~18 16~20 20~28 16~28 28~40 20~28 16~28 28~40 6 8 8 8 6 8 8 8 8 8 8 8 LCD 3/4 3/4 3/4 3/4 128~168 168~208 248~2416 3616~4816 3616~4816 248~2416 3616~4816 3616~4816 Timer 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 16-bit2 Stack 4 8 8 12 4 8 8 8 12 8 8 12 External Interrupt 3 4 4 4 3 4 4 4 4 4 4 4 DTMF Generator O O O O O O O O O O O O FSK Receiver 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 O O O Package 28SOP 48SSOP 48SSOP 64QFP 56SSOP 64QFP 100QFP 100QFP 128QFP 128QFP 128QFP 128QFP
Note: Part numbers suffixed with P are OTP devices, all others are mask version devices.
Block Diagram (HT95L400/40P)
RES PowerDown D e te c to r & R e s e t C ir c u it P ro g ra m C o u n te r P ro g ra m ROM STACK0 STACK1 STACK2 32768H z IN T /T M R 1 M U X 32768H z M U X c lo c k /4 PA0~PA7 TM R0
In te rru p t C ir c u it IN T C 0 IN T C 1
TM R1 TM R1C
STACK9 STAC K10 STAC K11
RTC
In s tr u c tio n R e g is te r
TM R0 TM R0C MP0 MP1 M U X DATA M e m o ry
S y s te m PA PAC PB PBC
PB0~PB7
In s tr u c tio n D ecoder ALU T im in g G e n e ra to r ACC
MUX
PD PDC STATUS PE PEC PF PFC
PD 0~PD 7
PE0~PE3
S h ifte r
PF0~PF7
X1 X2 XC HFI HFO HDI HDO HKS PO DNPO XM UTE VDD VSS
OSC
C ir c u it
32768H z W DT OSC S y s te m C lo c k /4 M
W DTS U X W D T P r e s c a le r
PG PGC DTM F G e n e ra to r 3 .5 8 M H z 32768H z o r 3 .5 8 M H z /4
PG 0~PG 3
DTM F
D ia le r I/O
Power S u p p ly
Low B a tte ry D e te c to r
PFD L C D D r iv e r
M U S IC
L B IN
C O M 0~C O M 15 SEG 0~SEG 47
VLCD
Rev. 1.20
2
May 26, 2004
HT95LXXX
Pin Assignment
HT95L400/40P
CO CO CO CO CO CO C C C C C C C C C C C C S EG EG EG M1 M1 M1 M1 M1 M1 OM OM OM OM OM OM OM OM OM OM N N PG PG PG PG PF PF6 PF5 PF4 PF3 PF2 PF1 PF0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 XM UTE DNPO PO HKS HDO HDI HFO HFI VSS VDD IN T /T M R 1 NC NC NC NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 128 127126 125124 123122121120119118117 116115114113112111110109108107106105104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
S
S
0 2 3 4 5 0 1 2 3 4 5 6 7 8 9 0 1 7 0 1 2 NC NC NC SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE SE NC NC NC NC NC G3 G4 G5 G6 G7 G8 G9 G1 G1 G1 G1 G1 G1 G1 G1 G1 G1 G2 G2 G2 G2 G2 G2 G2 G2 G2 G2 G3 G3 G3 2
1
2
3
H T 9 5 L 4 0 0 /4 0 P 1 2 8 Q F P -A
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
NC SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG VLC MUS RES TM R DTM L B IN XC X1 X2 NC D 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 F IC 0 /P /P /P /P /P /P /P /P /P /P /P /P D0 D1 D2 D3 D4 D5 D6 D7 E0 E1 E2 E3
Rev. 1.20
3
May 26, 2004
HT95LXXX
HT95L300/30P
C SEG SEG SEG SEG SEG OM1 OM1 OM1 OM1 OM1 OM1 COM COM COM COM COM COM COM COM COM 4 3 2 1 COM0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 XM UTE DNPO PO HKS HDO HDI HFO HFI VSS VDD IN T /T M R 1 X2 X1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 4445 46 4748 49 50
100 99 98 97 96 9594 93 92 91 90 89 88 87 86 8584 83 82 81
C
C
C
C
C
1
80 79 78 77 76 75 74 73 72 71 70 69 68
2
3
4
5
6
7
H T 9 5 L 3 0 0 /3 0 P 1 0 0 Q F P -A
8
67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
9 SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SGE SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG VLC MUS RES TM R DTM L B IN XC D 35 36 37 38 39 40 41 42 43 44 45 46 47 0 F IC /P /P /P /P /P /P /P /P /P /P /P /P D0 D1 D2 D3 D4 D5 D6 D7 E0 E1 E2 E3
0
1
2
3
4
5
0
HT95L200/20P
CO CO CO CO CO CO CO CO
100 99 98 97 96 9594 93 92 91 90 89 88 87 86 8584 83 82 81
C C M7 M6 M5 M4 M3 M2 M1 M0 OM9 OM8 /P D 7 /P D 6 /P D 5 /P D 4 /P D 3 /P D 2 /P D 1 /P D 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6
NC NC NC NC NC NC PB5 PB4 PB3 PB2 PB1 PB0 XM UTE DNPO PO HKS HDO HDI HFO HFI NC NC NC NC VSS VDD IN T /T M R 1 X2 X1
7 8 9 4 5 6 3 2 1
80 79 78 77 76 75 74 73 72
NC NC NC NC COM COM COM COM COM COM SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG SEG NC NC NC NC 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
NC
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 4445 46 4748 49 50
71 70 69 68
H T 9 5 L 2 0 0 /2 0 P 1 0 0 Q F P -A
67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
10 11 12 13 14 15
SE SE SE SE SE SE SE SE PE PE PE PE NC VL MU RE TM DT LB XC CD S IC S R0 MF IN 3 2 1 0 G 16 G 17 G 18 G 19 G 20 G 21 G 22 G 23
Rev. 1.20
4
May 26, 2004
HT95LXXX
HT95L100/10P, HT95L000/00P
PA3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PA2 PA1 PA0 PB5 PB4 VSS 51 50 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
PA4 PA5 PA6 PA7 X1 X2 XC NC VDD RES DTM F NC NC HFI HFO XM UTE DNPO PO HKS NC S E G 1 5 /P E 3 S E G 1 4 /P E 2 S E G 1 3 /P E 1 S E G 1 2 /P E 0 SEG 11 SEG 10 SEG9 SEG8
COM1
COM0
1 2
64 63 62 61 60 59 58 57 56 55 54 53 52
COM2
COM3
COM4
COM5
COM6
COM7
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5 SEG6 SEG7 SEG8 SEG9 SEG 10 SEG 11 SEG 12 SEG 13 SEG 14 SEG 15 S E G 1 6 /P E 0 S E G 1 7 /P E 1 S E G 1 8 /P E 2 S E G 1 9 /P E 3 VLC D M U S IC RES TM R0 DTM F
PB3 PB2 PB1 PB0 IN T COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7
PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 XM UTE DNPO
49 48 47 46 45 44
H T 9 5 L 1 0 0 /1 0 P 6 4 Q F P -A
43 42 41 40 39 38 37 36 35 34 33
Pin Description
Pin Name CPU VDD VSS X1 X2 XC RES 3/4 3/4 I O I I Positive power supply Negative power supply, ground A 32768Hz crystal (or resonator) should be connected to this pin and X2. A 32768Hz crystal (or resonator) should be connected to this pin and X1. External low pass filter used for frequency up conversion circuit. Schmitt trigger reset input, active low. Supported for HT95L000/00P Schmitt trigger input for external interrupt No internal pull-high resistor. Edge trigger activated on a falling edge. Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P Schmitt trigger input for external interrupt or Timer/Event Counter 1. No internal pull-high resistor. For INT: Edge trigger activated on a falling edge. For TMR1: Activated on falling or rising transition edge, selected by software. Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P Schmitt trigger input for Timer/Event Counter 0. No internal pull-high resistor. Activated on falling or rising transition edge, selected by software. I/O Description
PO
HKS
HDO
HDI
HFO
HFI
VSS
VDD
IN T /T M R 1
X1
X2
XC
L B IN
H T 9 5 L 0 0 0 /0 0 P 5 6 S S O P -A
INT
I
INT/TMR1
I
TMR0
I
Rev. 1.20
5
May 26, 2004
HT95LXXX
Pin Name LCD Driver SEG47~SEG0 O or I/O O or I/O I LCD panel segment outputs. Some segment outputs can be optioned to Bidirectional input/output ports by software. (See the LCD Driver function) LCD panel common outputs. Some common outputs can be optioned to Bidirectional input/output ports by software. (See the LCD Driver function) LCD driver power source. Bidirectional input/output ports. Schmitt trigger input and CMOS output. See mask option table for pull-high and wake-up function Bidirectional input/output ports. Schmitt trigger input and CMOS output. See mask option table for pull-high function Bidirectional input/output ports. Schmitt trigger input and CMOS output. See mask option table for pull-high function Port D could be optioned to LCD signal output, see the Input/Output Ports function Bidirectional input/output ports. Schmitt trigger input and CMOS output. See mask option table for pull-high function Port E could be optioned to LCD signal output, see the Input/Output Ports function Bidirectional input/output ports. Schmitt trigger input and CMOS output. See mask option table for pull-high function Bidirectional input/output ports. Schmitt trigger input and CMOS output. See mask option table for pull-high function Schmitt trigger input structure. An external RC network is recommended for input debouncing. This pin is pulled low with internal resistance of 200kW typ. CMOS output structure. Schmitt trigger input structure. An external RC network is recommended for input debouncing. This pin is pulled high with internal resistance of 200kW typ. CMOS output structure. This pin detects the status of the hook-switch and its combination with HFI/HDI can control the PO pin output to make or break the line. CMOS output structure controlled by HKS and HFI/HDI pins and which determines whether the dialer connects or disconnects the telephone line. NMOS output structure. NMOS output structure. Usually, XMUTE is used to mute the speech circuit when transmitting the dialer signal. This pin outputs dual tone signals to dial out the phone number. The load resistor should not be less than 5kW. This pin outputs the single tone that is generated by the PFD generator. This pin detects battery low through external R1/R2 to determine threshold voltage. I/O Description
COM15~COM0 VLCD Normal I/O PA7~PA0
I/O
PB7~PB0
I/O
PD7~PD0
I/O
PE3~PE0
I/O
PF7~PF0
I/O
PG3~PG0
I/O
Dialer I/O (See the Dialer I/O Function) HFI HFO HDI HDO HKS PO DNPO XMUTE Peripherals DTMF MUSIC LBIN O O I I O I O I O O O
Rev. 1.20
6
May 26, 2004
HT95LXXX
Absolute Maximum Ratings
Supply Voltage ..........................VSS-0.3V to VSS+5.5V Input Voltage .............................. VSS-0.3 to VDD+0.3V Storage Temperature ...........................-50C to 125C Operating Temperature ..........................-20C to 70C
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Electrical Characteristics
Symbol CPU IIDL Idle Mode Current 5V 32768Hz off, 3.58MHz off, CPU off, LCD off, WDT off, no load 32768Hz on, 3.58MHz off, CPU off, LCD off, WDT off, no load 32768Hz on, 3.58MHz off, CPU on, LCD off, WDT off, no load 32768Hz on, 3.58MHz on, CPU on, LCD on, WDT on, DTMF generator off, no load 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 2 Parameter Test Conditions VDD Conditions Min. Typ. Max.
Ta=25C Unit
mA
ISLP
Sleep Mode Current
5V
3/4
3/4
30
mA
IGRN
Green Mode Current
5V
3/4
3/4
50
mA
INOR VIL VIH IOL IOH RPH VLBIN
Normal Mode Current I/O Port Input Low Voltage I/O Port Input High Voltage I/O Port Sink Current I/O Port Source Current Pull-high Resistor Low Battery Detection Reference voltage LCD Panel Power Supply LCD Operation Current XMUTE Leakage Current XMUTE Sink Current HKS Input Current HFI Pull-low Resistance HDI Pull-high Resistance HFO Source Current HFO Sink Current HDO Source Current HDO Sink Current PO Source Current PO Sink Current DNPO Sink Current
5V 5V 5V 5V 5V 5V 5V
3/4 0 4 4 -2 10 1.10
3/4 3/4 3/4 6 -3 30 1.15
3 1 5 3/4 3/4 3/4 1.20
mA V V mA mA kW V
LCD Driver VLCD ILCD Dialer I/O IXMO IOLXM IHKS RHFI RHDI IOH2 IOL2 IOH3 IOL3 IOH4 IOL4 IOL5 2.5V XMUTE pin=2.5V 2.5V XMUTE pin=0.5V 2.5V HKS pin=2.5V 2.5V VHFI=2.5V 2.5V VHDI=0V 2.5V VOH=2V 2.5V VOL=0.5V 2.5V VOH=2V 2.5V VOL=0.5V 2.5V VOH=2V 2.5V VOL=0.5V 2.5V VOL=0.5V 3/4 1 3/4 3/4 3/4 -1 1 -1 1 -1 1 1 3/4 3/4 3/4 200 200 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1 3/4 0.1 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 mA mA mA kW kW mA mA mA mA mA mA mA 3/4 3/4 3/4 VLCD=5V, 32768Hz, no load 3/4 3/4 3 3/4 5 100 V mA
Rev. 1.20
7
May 26, 2004
HT95LXXX
Symbol DTMF Generator VTDC VTOL VTAC RL ACR THD DTMF Output DC Level DTMF Sink Current DTMF Output AC Level DTMF Output Load Column Pre-emphasis Tone Signal Distortion 3/4 3/4 3/4 3/4 3/4 3/4 VDTMF=0.5V Row group, RL=5kW THD-23dB Row group=0dB RL=5kW 3/4 0.45VDD 0.1 120 5 1 3/4 3/4 3/4 155 3/4 2 -30 0.7VDD 3/4 180 3/4 3 -23 V mA mVrms kW dB dB Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit
Functional Description
Execution Flow The system clock for the telephone controller is derived from a 32768Hz crystal oscillator. A built-in frequency up conversion circuit provides dual system clock, namely; 32768Hz and 3.58MHz. The system clock is internally divided into four non-overlapping clocks. One instruction cycle consists of four system clock cycles. Instruction fetching and execution are pipelined in such a way that a fetch takes an instruction cycle while decoding and execution takes the next instruction cycle. The pipelining scheme causes each instruction to be effectively executed in a instruction cycle. If an instruction changes the program counter, two instruction cycles are required to complete the instruction. Program Counter - PC The program counter (PC) controls the sequence in which the instructions stored in the program ROM are executed and its contents specify a full range of program memory. After accessing a program memory word to fetch an instruction code, the contents of the program counter are incremented by 1. The program counter then points to the memory word containing the next instruction code. When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from subroutine, the program counter manipulates the program transfer by loading the address corresponding to
T1 T2 T3 T4 T1 T2
each instruction. The conditional skip is activated by instructions. Once the condition is met, the next instruction, fetched during the current instruction execution, is discarded and a dummy cycle replaces it to get the proper instruction. Otherwise proceed to the next instruction. The program counter lower order byte register (PCL:06H) is a readable and write-able register. Moving data into the PCL performs a short jump. The destination will be within 256 locations. When a control transfer takes place, an additional dummy cycle is required. Program Memory - ROM The program memory is used to store the program instructions which are to be executed. It also contains data, table, and interrupt entries, and is organized into 8K16 bits2 banks (HT95L400/40P), 8K16 bits (HT95L300/30P, HT95L200/20P) or 4K16 bits (HT95L100/10P, HT95L000/00P), addressed by the program counter and table pointer. For the HT95L400/40P, the program memory is divided into 2 banks, each bank having a ROM Size 8K16 bits. To move from the present ROM bank to a different ROM bank, the higher 1 bits of the ROM address are set by the BP (Bank Pointer), while the remaining 13 bits of the PC are set in the usual way by executing the appropriate jump or call instruction. As the 14 address bits are latched during the execution of a call or jump instruction, the correct value of the BP must first be setup before a
T3 T4 T1 T2 T3 T4
S y s te m
C lo c k
PC
PC
PC+1
PC+2
F e tc h IN S T (P C ) E x e c u te IN S T (P C -1 )
F e tc h IN S T (P C + 1 ) E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 ) E x e c u te IN S T (P C + 1 )
Execution Flow
Rev. 1.20
8
May 26, 2004
HT95LXXX
Mode Initial reset External interrupt Timer/Event Counter 0 overflow Timer/Event Counter 1 overflow RTC interrupt Dialer I/O interrupt Skip Loading PCL Jump, call branch Return from subroutine *13 *12 *11 Program Counter *13 0 0 0 0 0 0 *12 0 0 0 0 0 0 *11 0 0 0 0 0 0 *10 0 0 0 0 0 0 *9 0 0 0 0 0 0 *8 0 0 0 0 0 0 *7 0 0 0 0 0 0 *6 0 0 0 0 0 0 *5 0 0 0 0 0 0 *4 0 0 0 0 1 1 *3 0 0 1 1 0 1 *2 0 1 0 1 1 0 *1 0 0 0 0 0 0 *0 0 0 0 0 0 0
Program Counter+2 (within current bank) *10 *9 #9 S9 *8 #8 S8 @7 #7 S7 @6 #6 S6 @5 #5 S5 @4 #4 S4 @3 #3 S3 @2 #2 S2 @1 #1 S1 @0 #0 S0
BP.5 #12 #11 #10 S13 S12 S11 S10
Program ROM Address Note: *13~*0: Program counter bits #12~#0: Instruction code bits S13~S0: Stack register bits @7~@0: PCL bits
Available bits of program counter for HT95L400/40P: Bit 13~Bit 0 Available bits of program counter for HT95L300/30P: Bit 12~Bit 0 Available bits of program counter for HT95L200/20P: Bit 12~Bit 0 Available bits of program counter for HT95L100/10P: Bit 11~Bit 0 Available bits of program counter for HT95L000/00P: Bit 11~Bit 0
jump or call is executed. When either a software or hardware interrupt is received, note that no matter which ROM bank the program is in, the program will always jump to the appropriate interrupt service address in Bank 0. The original 14 bits address will be stored on the stack and restored when the relevant RET/RETI instruction is executed, automatically returning the program to the original ROM bank. This eliminates the need for programmers to manage the BP when interrupts occur. Certain locations in the program memory are reserved for special usage:
* Location 0000H (Bank0)
000H 004H 008H 00C H 010H 014H 018H
D e v ic e In itia liz a tio n P r o g r a m E x te r n a l In te r r u p t S u b r o u tin e T im e r /E v e n t C o u n te r 0 In te r r u p t S u b r o u tin e T im e r /E v e n t C o u n te r 1 In te r r u p t S u b r o u tin e R e s e rv e d R T C In te r r u p t S u b r o u tin e D ia le r I/O In te r r u p t S u b r o u tin e P ro g ra m ROM
This area is reserved for the initialization program. After chip power-on reset or external reset or WDT time-out reset, the program always begins execution at location 0000H.
* Location 0004H (Bank0)
100H 1FFH
L o o k - u p T a b le ( 2 5 6 W o r d s )
L o o k - u p T a b le ( 2 5 6 W o r d s ) (L a s t P a g e s ) 1 6 b its N o te : T T T T T he he he he he La La La La La st st st st st pa pa pa pa pa ge ge ge ge ge fo fo fo fo fo rH rH rH rH rH T9 T9 T9 T9 T9 5L 5L 5L 5L 5L 40 30 20 10 00 0 /4 0 /3 0 /2 0 /1 0 /0 0P 0P 0P 0P 0P is is is is is 3F 1F 1F 0F 0F 00 00 00 00 00 H~ H~ H~ H~ H~ 3F 1F 1F 0F 0F FF FF FF FF FF H H H H H
This area is reserved for the external interrupt service program. If the INT/TMR1 input pin is activated, the external interrupt is enabled and the stack is not full, the program begins execution at location 0004H.
* Location 0008H (Bank0)
This area is reserved for the Timer/Event Counter 0 interrupt service program. If a timer interrupt results from a Timer/Event Counter 0 overflow, the Timer/Event Counter 0 interrupt is enabled and the stack is not full, the program begins execution at location 0008H.
Program Memory
Rev. 1.20
9
May 26, 2004
HT95LXXX
* Location 000CH (Bank0)
This location is reserved for the Timer/Event Counter 1 interrupt service program. If a timer interrupt results from a Timer/Event Counter 1 overflow, the Timer/Event Counter 1 interrupt is enabled and the stack is not full, the program begins execution at location 000CH.
* Location 0014H (Bank0)
This location is reserved for real time clock (RTC) interrupt service program. When RTC generator is enabled and time-out occurs, the RTC interrupt is enabled and the stack is not full, the program begins execution at location 0014H.
* Location 0018H (Bank0)
This location is reserved for the HKS pin edge transition or HDI pin falling edge transition or HFI pin rising edge transition. If this condition occurs, the dialer I/O interrupt is enabled and the stack is not full, the program begins execution at location 18H. Table Location Any location in the ROM space can be used as look-up tables. The instructions TABRDC [m] (the current page, one page=256 words) and TABRDL [m] (the last page) transfer the contents of the lower-order byte to the HT95L400/40P Instruction(s) TABRDC [m] TABRDL [m]
specified data memory, and the higher-order byte to TBLH (08H). For the HT95L400/40P, the instruction TABRDC [m] is used for any page of any bank. Only the destination of the lower-order byte in the table is well-defined, and the higher-order byte of the table word is transferred to TBLH. The table pointer (TBLP) or (TBHP, TBLP for the HT95L400/40P) is a read/write register (07H) or (1FH, 07H for the HT95L400/40P), which indicates the table location. Before accessing the table, the location must be placed in the (TBLP) or (TBHP, TBLP for the HT95L400/40P). The TBLH is read only and cannot be restored. If the main routine and the ISR (Interrupt Service Routine) both employ the table read instruction, the contents of the TBLH in the main routine are likely to be changed by the table read instruction used in the ISR. Errors will then occur. Hence, simultaneously using the table read instruction in the main routine and the ISR should be avoided. However, if the table read instruction has to be applied in both the main routine and the ISR, the interrupt should be disabled prior to the table read instruction. It will not be enabled until the TBLH has been backed-up. All table related instructions require two cycles to complete the operation. These areas may function as normal program memory depending on the requirements.
Table Location *13 #5 1 *12 #4 1 *11 #3 1 *10 #2 1 *9 #1 1 *8 #0 1 *7 @7 @7 *6 @6 @6 *5 @5 @5 *4 @4 @4 *3 @3 @3 *2 @2 @2 *1 @1 @1 *0 @0 @0
HT95L300/30P, HT95L200/20P Instruction(s) TABRDC [m] TABRDL [m] Table Location *12 P12 1 *11 P11 1 *10 P10 1 *9 P9 1 *8 P8 1 *7 @7 @7 *6 @6 @6 *5 @5 @5 *4 @4 @4 *3 @3 @3 *2 @2 @2 *1 @1 @1 *0 @0 @0
HT95L100/10P, HT95L000/00P Instruction(s) TABRDC [m] TABRDL [m] Table Location *11 P11 1 *10 P10 1 *9 P9 1 *8 P8 1 *7 @7 @7 *6 @6 @6 *5 @5 @5 *4 @4 @4 *3 @3 @3 *2 @2 @2 *1 @1 @1 *0 @0 @0
Note: *13~*0: Table location bits @7~@0: TBLP register bit7~bit0
#7~#0: TBHP register bit7~bit0 P12~P8: Current program counter bits
Rev. 1.20
10
May 26, 2004
HT95LXXX
Stack Register This is a special part of the memory which is used to save the contents of the program counter only. The stack is organized into 12 levels (HT95L400/40P), 8 levels (HT95L300/30P, HT95L200/20P, HT95L100/10P) or 4 levels (HT95L000/00P) and is neither part of the data nor part of the program space, and is neither readable nor writable. The activated level is indexed by the stack pointer (SP) and is neither readable nor writable. At a subroutine call or interrupt acknowledge signal, the contents of the program counter are pushed onto the stack. At the end of a subroutine or an interrupt routine, signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the stack. After a chip reset, the SP will point to the top of the stack. If the stack is full and an interrupt takes place, the interrupt request flag will be recorded but the acknowledge signal will be inhibited even if this interrupt is enabled. When the stack pointer is decremented (by RET or RETI), the interrupt will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily. If the stack is full and a CALL is subsequently executed, stack overflow occurs and the first entry will be lost (only the most recent 12, 8 or 4, depending on various MCU type, returned addresses are stored). Data Memory The data memory is divided into four functional groups: special function registers, embedded control register, LCD display memory and general purpose memory. Most are read/write, but some are read only. Special Register, Embedded Control Register, LCD Display Memory and General Purpose RAM BP Address (RAM Bank) Function Description Supported for HT95LXXX 400/P 300/P 200/P 100/P 000/P O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O The special function registers are located from 00H to 1FH. The embedded control registers are located in the memory areas from 20H to 3FH. The remaining spaces which are not specified in the following table before the 40H are reserved for future expanded usage and reading these locations will get 00H. The general purpose data memory is divided into 15 banks (HT95L400/40P), 11 banks (HT95L300/30P), 6 banks (HT95L200/20P, HT95L100/10P) or 2 banks (HT95L000/00P). The banks in the RAM are all addressed from 40H to 0FFH and they are selected by setting the value of the bank pointer (BP). All of the data memory areas can handle arithmetic, logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the data memory can be set and reset by SET [m].i and CLR [m].i. They are also indirectly accessible through memory pointer registers (MP0 or MP1). The bank1~bank14 and bank27 are only indirectly accessible through memory pointer 1 register (MP1). The LCD display memory is located at bank 1BH. They can be read and written to by the indirect addressing mode using memory pointer 1 (MP1). To turn the display On or Off, a 1 or 0 is written to the corresponding bit of the memory area.
Special Function Register 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH IAR0 MP0 IAR1 MP1 BP ACC PCL TBLP TBLH WDTS STATUS INTC0 TMR0H Indirect addressing register 0 Memory pointer register 0 Indirect addressing register 1 Memory pointer register 1 Bank Pointer register Accumulator Program counter lower-order byte register Table pointer Table higher-order byte register Watchdog Timer option setting register Status register Interrupt control register 0 Timer/Event Counter 0 high-order byte register
Rev. 1.20
11
May 26, 2004
HT95LXXX
BP Address (RAM Bank) 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 18H 19H 1AH 1BH 1EH 1FH Function TMR0L TMR0C TMR1H TMR1L TMR1C PA PAC PB PBC DIALERIO PD PDC PE PEC INTC1 TBHP Description Timer/Event Counter 0 low-order byte register Timer/Event Counter 0 control register Timer/Event Counter 1 high-order byte register Timer/Event Counter 1 low-order byte register Timer/Event Counter 1 control register Port A data register Port A control register Port B data register Port B control register Dialer I/O register Port D data register Port D control register Port E data register Port E control register Interrupt control register 1 Table high-order byte pointer Supported for HT95LXXX 400/P 300/P 200/P 100/P 000/P O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 3/4 O O O O O O O O O 3/4 3/4 3/4 3/4 O O O O O O O O O O O O O O O O O O O O O O O O 3/4 O O O O O 3/4 O O O 3/4 3/4 3/4 3/4 O O O O O O 3/4 3/4 3/4 O O O O O O O O O O 3/4 3/4 O O O 3/4 O O O O O O O O O 3/4 3/4 3/4 3/4 O O O O O O 3/4 3/4 3/4 O O O O O O O O O O 3/4 3/4 O O O 3/4 O O 3/4 O O O O 3/4 3/4 3/4 3/4 3/4 3/4 O O 3/4 3/4 3/4 3/4 3/4 3/4 3/4
Embedded Control Register 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 20H 21H 22H 24H 26H 28H 2DH 2EH 2FH 34H 35H 36H 37H DTMFC DTMFD LINE RTCC MODE LCDIO LCDC PFDC PFDD PF PFC PG PGC DTMF generator control register DTMF generator data register Line control register Real time clock control register Operation mode control register LCD segment and I/O option register LCD driver control register PFD control register PFD data register Port F data register Port F control register Port G data register Port G control register
General Purpose RAM 00H 01H 02H 03H 04H 05H 06H 07H 08H 40H~FFH BANK0 RAM General purpose RAM space 40H~FFH BANK1 RAM General purpose RAM space 40H~FFH BANK2 RAM General purpose RAM space 40H~FFH BANK3 RAM General purpose RAM space 40H~FFH BANK4 RAM General purpose RAM space 40H~FFH BANK5 RAM General purpose RAM space 40H~FFH BANK6 RAM General purpose RAM space 40H~FFH BANK7 RAM General purpose RAM space 40H~FFH BANK8 RAM General purpose RAM space
Rev. 1.20
12
May 26, 2004
HT95LXXX
BP Address (RAM Bank) 09H 0AH 0BH 0CH 0DH 0EH Function Description Supported for HT95LXXX 400/P 300/P 200/P 100/P 000/P O O O O O O O O 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4
40H~FFH BANK9 RAM General purpose RAM space 40H~FFH BANK10 RAM General purpose RAM space 40H~FFH BANK11 RAM General purpose RAM space 40H~FFH BANK12 RAM General purpose RAM space 40H~FFH BANK13 RAM General purpose RAM space 40H~FFH BANK14 RAM General purpose RAM space
LCD RAM Display Memory 1BH 40H~9FH LCD RAM LCD RAM mapping space for COM0~COM15 (see LCD Driver function)
Indirect Addressing Register Location 00H and 02H are indirect addressing registers that are not physically implemented. Any read/write operation of [00H] and [02H] will access the memory pointed to by MP0 and MP1, respectively. Reading location [00H] or [02H] indirectly returns the result 00H, while writing it leads to no operation. MP0 is indirectly addressable in bank0, but MP1 is available for all banks by switch BP [04H]. If BP is unequal to 00H, the indirect addressing mode to read/write operation from 00H~3FH will return the result as same as the value of bank0. The memory pointer registers MP0 and MP1 are 8-bits registers, and the bank pointer register BP is 6-bits register for the HT95L400/40P or 5-bits for the other devices in the series. Accumulator The accumulator is closely related to ALU operations. It is also mapped to location 05H of the data memory and can operate with immediate data. All data movement between two data memory locations must pass through the accumulator.
Arithmetic and Logic Unit - ALU This circuit performs 8-bit arithmetic and logic operations and provides the following functions:
* Arithmetic operations (ADD, ADC, SUB, SBC, DAA) * Logic operations (AND, OR, XOR, CPL) * Rotation (RL, RR, RLC, RRC) * Increment and Decrement (INC, DEC) * Branch decision (SZ, SNZ, SIZ, SDZ, etc.)
The ALU not only saves the results of a data operation but also changes the status register. Status Register - STATUS This status register contains the carry flag (C), auxiliary carry flag (AC), zero flag (Z), overflow flag (OV), power down flag (PDF), and watchdog time-out flag (TO). It also records the status information and controls the operation sequence. Except for the TO and PDF flags, bits in the status register can be altered by instructions, similar to the other registers. Data written into the status register will not change the TO or PDF flag. Operations related to the
Register
Label C
Bits 0
Function C is set if the operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. Also it is affected by a rotate through carry instruction. AC is set if the operation results in a carry out of the low nibbles in addition or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared. Z is set if the result of an arithmetic or logic operation is 0; otherwise Z is cleared. OV is set if the operation results in a carry into the highest-order bit but not a carry out of the highest-order bit, or vice versa; otherwise OV is cleared. PDF is cleared when either a system power-up or executing the CLR WDT instruction. PDF is set by executing the HALT instruction. TO is cleared by a system power-up or executing the CLR WDT or HALT instruction. TO is set by a WDT time-out. Unused bit, read as 0
AC Z STATUS (0AH) OV PDF TO 3/4
1 2 3 4 5 6, 7
Rev. 1.20
13
May 26, 2004
HT95LXXX
status register may yield different results from those intended. The TO flag can be affected only by system power-up, a WDT time-out or executing the CLR WDT or HALT instruction. The PDF flag can be affected only by executing the HALT or CLR WDT instruction or during a system power-up. The Z, OV, AC and C flags generally reflect the status of the latest operations. On entering the interrupt sequence or executing the subroutine call, the status register will not be automatically pushed onto the stack. If the contents of the status are important and if the subroutine can corrupt the status register, precautions must be taken to save it . Interrupt The telephone controller provides an external interrupt, internal timer/event counter interrupt, an internal real time clock interrupt and internal dialer I/O interrupt. The Interrupt Control Registers 0 and Interrupt Control Register 1 both contains the interrupt control bits that set the enable/disable and the interrupt request flags. Once an interrupt subroutine is serviced, all the other interrupts will be blocked (by hardware clearing the EMI bit). This scheme may prevent any further interrupt nesting. Other interrupt requests may occur during this interval but only the interrupt request flag is recorded. If a certain interrupt requires servicing within the service routine, the EMI bit and the corresponding bit of the INTC0 (INTC1) may be set to allow interrupt nesting. If the stack is full, any other interrupt request will not be acknowledged, even if the related interrupt is enabled, until the stack pointer is decremented. If immediate service is desired, the stack must be prevented from becoming full. All these kinds of interrupts have a wake-up capability. As an interrupt is serviced, a control transfer occurs by pushing the program counter onto the stack, followed by a branch to a subroutine at specified location in the program memory. Only the program counter is pushed onto the stack. If the contents of the register or status register (STATUS) are altered by the interrupt service program which corrupts the desired control sequence, the contents should be saved in advance. External interrupt is triggered by a high to low transition of the INT/TMR1 pin and the interrupt request flag EIF will be set. When the external interrupt is enabled, the stack is not full and the external interrupt is active, a subroutine call to location 04H will occur. The interrupt request flag EIF and EMI bits will be cleared to disable other interrupts. The Timer/Event Counter 0 interrupt is generated by a timeout overflow and the interrupt request flag T0F will be set. When the Timer/Event Counter 0 interrupt is enabled, the stack is not full and the T0F bit is set, a subroutine call to location 08H will occur. The interrupt request flag T0F and EMI bits will be cleared to disable further interrupts. The Timer/Event Counter 1 interrupt is generated by a timeout overflow and the interrupt request flag T1F will be set. When the Timer/Event Counter 1 interrupt is enabled, the stack is not full and the T1F bit is set, a subFunction Controls the master (global) interrupt (1=enabled; 0=disabled) Controls the external interrupt (1=enabled; 0=disabled) Controls the Timer/Event Counter 0 interrupt (1=enabled; 0=disabled) Controls the Timer/Event Counter 1 interrupt (1=enabled; 0=disabled) External interrupt request flag (1=active; 0=inactive) Timer/Event Counter 0 request flag (1=active; 0=inactive) Timer/Event Counter 1 request flag (1=active; 0=inactive) Unused bit, read as 0 Reserved, inhibit using Control the real time clock interrupt (1=enable; 0=disable) Control the dialer I/O interrupt (1=enable; 0=disable) Unused bit, read as 0 Reserved, inhibit using Internal real time clock interrupt request flag (1=active; 0=inactive) Internal dialer I/O interrupt request flag (1=active: 0=inactive) Unused bit, read as 0
Register
Bits 0 1 2
Label EMI EEI ET0I ET1I EIF T0F T1F 3/4 3/4 ERTCI EDRI 3/4 3/4 RTCF DRF 3/4
R/W RW RW RW RW RW RW RW RO RW RW RW RO RW RW RW RO
INTC0 (0BH)
3 4 5 6 7 0 1 2
INTC1 (1EH)
3 4 5 6 7
Rev. 1.20
14
May 26, 2004
HT95LXXX
routine call to location 0CH will occur. The interrupt request flag T1F and EMI bits will be cleared to disable further interrupts. The real time clock interrupt is generated by a 1Hz RTC generator. When the RTC time-out occurs, the interrupt request flag RTCF will be set. When the RTC interrupt is enabled, the stack is not full and the RTCF is set, a subroutine call to location 14H will occur. The interrupt request flag RTCF and EMI bits will be cleared to disable other interrupts. The dialer I/O interrupt is triggered by any edge transition onto HKS pin or a falling edge transition onto HDI pin or a rising edge transition onto HFI pin, the interrupt request flag DRF will be set. When the dialer I/O interrupt is enabled, the stack is not full and the DRF is set, a subroutine call to location 18H will occur. The interrupt request flag DRF and EMI bits will be cleared to disable other interrupts. Note: 1. If the dialer status is on-hook and hold-line, the falling edge transition onto HDI pin will not generate the dialer I/O interrupt. 2. The HDI input is supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P. 3. The dialer I/O interrupt will be disabled when the operation mode is in Idle mode. During the execution of an interrupt subroutine, other interrupt acknowledge signals are held until the RETI instruction is executed or the EMI bit and the related interrupt control bit are set to 1 (if the stack is not full). To return from the interrupt subroutine, RET or RETI may be invoked. RETI will set the EMI bit to enable an interrupt service, but RET will not. Interrupts, occurring in the interval between the rising edges of two consecutive T2 pulses, will be serviced on the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests the following table shows the priority that is applied. These can be masked by resetting the EMI bit. Interrupt Source External interrupt Timer/Event Counter 0 interrupt Timer/Event Counter 1 interrupt Real time clock interrupt Dialer I/O interrupt Priority 1 2 3 4 5 Vector 04H 08H 0CH 14H 18H It is recommended that a program should not use the CALL subroutine within the interrupt subroutine. Interrupts often occur in an unpredictable manner or need to be serviced immediately in some applications. If only one stack is left and enabling the interrupt is not well controlled, the original control sequence will be damaged once the CALL operates in the interrupt subroutine. Oscillator Configuration There are two oscillator circuits in the controller, the external 32768Hz crystal oscillator and internal WDT OSC. The 32768Hz crystal oscillator and frequency-up conversion circuit (32768Hz to 3.58MHz) are designed for dual system clock source. It is necessary for frequency conversion circuit to add external RC components to make up the low pass filter that stabilize the output frequency 3.58MHz (see the oscillator circuit). The WDT OSC is a free running on-chip RC oscillator, and no external components are required. Even if the system enters the Idle mode (the system clock is stopped), the WDT OSC still works within a period of 78ms normally. When the WDT is disabled or the WDT source is not this RC oscillator, the WDT OSC will be disabled.
X1 X2 XC
15kW 3nF 50nF
System Oscillator Circuit Watchdog Timer - WDT The WDT clock source is implemented by a WDT OSC or external 32768Hz or an instruction clock (system clock divided by 4), determined by the mask option. This timer is designed to prevent a software malfunction or sequence from jumping to an unknown location with unpredictable results. The Watchdog Timer can be disabled by mask option. If the Watchdog Timer is disabled, all the executions related to the WDT result in no operation. If the device operates in a noisy environment, using the on-chip WDT OSC or 32768Hz crystal oscillator is strongly recommended. When the WDT clock source is selected, it will be first divided by 512 (9-stage) to get the nominal time-out period. By invoking the WDT prescaler, longer time-out periods can be realized. Writing data to WS2, WS1, WS0 can give different time-out periods.
Priority of the Interrupt EMI, EEI, ET0I, ET1I, ERTCI and EDRI are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once the interrupt request flags (EIF, T0F, T1F, RTCF, DRF) are set by hardware or software, they will remain in the INTC0 or INTC1 registers until the interrupts are serviced or cleared by a software instruction.
Rev. 1.20
15
May 26, 2004
HT95LXXX
The WDT OSC period is 78ms. This time-out period may vary with temperature, VDD and process variations. The WDT OSC always works for any operation mode. If the instruction clock is selected as the WDT clock source, the WDT operates in the same manner except in the Sleep mode or Idle mode. In these two modes, the WDT stops counting and lose its protecting purpose. In this situation the logic can only be re-started by external logic. If the WDT clock source is the 32768Hz, the WDT also operates in the same manner except in the Idle mode. When in the Idle mode, the 32768Hz stops, the WDT stops counting and lose its protecting purpose. In this situation the logic can only be re-started by external logic. The high nibble and bit3 of the WDTS are reserved for user defined flags, which can be used to indicate some specified status. The WDT time-out under Normal mode or Green mode will initialize chip reset and set the status bit TO. But in the Sleep mode or Idle mode, the time-out will initialize a warm reset and only the program counter and stack pointer are reset to 0. To clear the WDT contents (including the WDT prescaler), three methods are adopted; external reset (a low level to RES pin), software instruction and a HALT instruction. The software instruction include CLR WDT and the other set CLR WDT1 and CLR WDT2. Of these two types of instruction, only one can be active depending on the mask option WDT instr. If the CLR WDT is selected (i.e. One clear instruction), any execution of the CLR WDT instruction will clear the WDT. In the case that
32768H z W DT OSC S y s te m C lo c k /4 M ask O p tio n S e le c t W D T P r e s c a le r 9 - b it C o u n te r 7 - b it C o u n te r
CLR WDT1 and CLR WDT2 are chosen (i.e. Two clear instructions), these two instructions must be executed to clear the WDT; otherwise, the WDT may reset the chip as a result of time-out. Controller Operation Mode Holteks telephone controllers support two system clock and four operation modes. The system clock could be 32768Hz or 3.58MHz and operation mode could be Normal, Green, Sleep or Idle mode. These are all selected by the software. The following conditions will force the operation mode to change to Green mode:
* Any reset condition from any operation mode * Any interrupt from Sleep mode or Idle mode * Port A wake-up from Sleep mode or Idle mode
How to change the Operation Mode
* Normal mode to Green mode:
Clear MODE1 to 0, then operation mode is changed to Green mode but the UPEN status is not changed. However, UPEN can be cleared by software.
* Normal mode or Green mode to Sleep mode:
Step 1: Clear MODE0 to 0 Step 2: Clear MODE1 to 0 Step 3: Clear UPEN to 0 Step 4: Execute HALT instruction After Step 4, operation mode is changed to Sleep mode.
* Normal mode or Green mode to Idle mode:
Step 1: Set MODE0 to 1 Step 2: Clear MODE1 to 0 Step 3: Clear UPEN to 0 Step 4: Execute HALT instruction After Step 4, operation mode is changed to Idle mode.
* Green mode to Normal mode:
W S0~W S2
8 -to -1 M U X W D T T im e - o u t
Watchdog Timer
Step 1: Set UPEN to 1 Step 2: Software delay 20ms Step 3: Set MODE1 to 1 After Step 3, operation mode is changed to Normal mode.
Register
Label
Bits
R/W
Function Watchdog Timer division ratio selection bits Bit 2, 1, 0=000, Division ratio=1:1 Bit 2, 1, 0=001, Division ratio=1:2 Bit 2, 1, 0=010, Division ratio=1:4 Bit 2, 1, 0=011, Division ratio=1:8 Bit 2, 1, 0=100, Division ratio=1:16 Bit 2, 1, 0=101, Division ratio=1:32 Bit 2, 1, 0=110, Division ratio=1:64 Bit 2, 1, 0=111, Division ratio=1:128 Unused bit. These bits are read/write-able.
WDTS (09H)
WS0 WS1 WS2
0 1 2
RW
3/4
7~3
RW
Rev. 1.20
16
May 26, 2004
HT95LXXX
Register Label 3/4 UPEN MODE (26H) Bits 4~0 5 R/W RO RW Unused bit, read as 0 1: Enable frequency up conversion function to generate 3.58MHz 0: Disable frequency up conversion function to generate 3.58MHz 1: Disable 32768Hz oscillator while the HALT instruction is executed (Idle mode) 0: Enable 32768Hz oscillator while the HALT instruction is executed (Sleep mode) 1: Select 3.58MHz as CPU system clock 0: Select 32768Hz as CPU system clock Function
MODE0
6
RW
MODE1
7
RW
Operation Mode Description HALT Instruction Not execute Not execute Be executed Be executed MODE1 1 0 0 0 MODE0 X X 0 1 UPEN 1 0 0 0 Operation Mode Normal Green Sleep Idle 32768Hz ON ON ON OFF 3.58MHz ON OFF OFF OFF System Clock 3.58MHz 32768Hz HALT HALT
Note: X means dont care
* Sleep mode or Idle mode to Green mode:
Method 1: Any reset condition occurred Method 2: Any interrupt is active Method 3: Port A wake-up Note:The Timer 0, Timer 1, RTC and dialer I/O interrupt function will not work at the Idle mode because the 32768Hz crystal is stopped. The reset conditions include power on reset, external reset, WDT time-out reset. By examining the processor status flag, PDF and TO, the program can distinguish between different reset conditions. Refer to the Reset function for detailed description. The port A wake-up and interrupt can be considered as a continuation of normal execution. Each bit in port A can be independently selected to wake-up the device by mask option. Awakening from Port A stimulus, the program will resume execution of the next instruction. Any valid interrupts from Sleep mode or Idle mode may cause two sequences. One is if the related interrupt is disabled or the interrupt is enabled but the stack is full, the program will resume execution at the next instruction. The other is if the interrupt is enabled and the stack is not full, the regular interrupt response takes place. It is necessary to mention that if an interrupt request flag is set to 1 before entering the Sleep mode or Idle mode, the wake-up function of the related interrupt will be disabled. Once a Sleep mode or Idle mode wake-up event occurs, it will take SST delay time (1024 system clock period) to
resume to Green mode. In other words, a dummy period is inserted after a wake-up. If the wake-up results from an interrupt acknowledge signal, the actual interrupt subroutine execution will be delayed by one or more cycles. If the wake-up results in the next instruction execution, this will be executed immediately after the dummy period is finished. To minimize power consumption, all the I/O pins should be carefully managed before entering the Sleep mode or Idle mode. The Sleep mode or Idle mode is initialized by the HALT instruction and results in the following.
* The system clock will be turned off. * The WDT function will be disabled if the WDT clock
source is the instruction clock.
* The WDT function will be disabled if the WDT clock
source is the 32768Hz in Idle mode.
* The WDT will still function if the WDT clock source is
the WDT OSC.
* If the WDT function is still enabled, the WDT counter
and WDT prescaler will be cleared and recounted again.
* The contents of the on chip RAM and registers remain
unchanged.
* All the I/O ports maintain their original status. * The flag PDF is set and the flag TO is cleared by hard-
ware.
Rev. 1.20
17
May 26, 2004
HT95LXXX
Reset There are three ways in which a reset can occur.
* Power on reset. * A low pulse onto RES pin. * WDT time-out.
VDD RES S S T T im e - o u t C h ip R eset tS
ST
After these reset conditions, the Program Counter and Stack Pointer will be cleared to 0. To guarantee that the system oscillator is started and stabilized, the SST (System Start-up Timer) provides an extra-delay of 1024 system clock pulses when the system is reset or awakes from the Sleep or Idle operation mode.
V
DD
Reset Timing Chart By examining the processor status flags PDF and TO, the software program can distinguish between the different chip resets. TO 0 u 0 PDF 0 u 1 u 1 Reset Condition Power on reset External reset during Normal mode or Green mode External reset during Sleep mode or Idle mode WDT time-out during Normal mode or Green mode WDT time-out during Sleep mode or Idle mode
100kW RES 0 .1 m F
1 1
Reset Circuit
Note: u means unchanged The functional units chip reset status are shown below:
W a rm R eset
HALT W DT W D T tim e - o u t
Program Counter Interrupt Prescaler
000H Disabled Cleared Cleared After a master reset, WDT begins counting. (If WDT function is enabled by mask option) Input mode Points to the top of the stack
E x te rn a l
RES SST 1 0 - b it R ip p le C o u n te r S y s te m R eset
C o ld R e s e t
SYSCLK
WDT
Timer/Event Counter 0/1 Off Reset Configuration Input/output Port Stack Pointer
When the reset conditions occurred, some registers may be changed or unchanged. (HT95L400/40P) Reset Conditions Register IAR0 MP0 IAR1 MP1 BP ACC PCL TBLP TBLH Addr. 00H 01H 02H 03H 04H 05H 06H 07H 08H Power On xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx ---0 0000 xxxx xxxx 0000H xxxx xxxx xxxx xxxx RES Pin uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---0 0000 uuuu uuuu 0000H uuuu uuuu uuuu uuuu RES Pin (Sleep/Idle) uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---0 0000 uuuu uuuu 0000H uuuu uuuu uuuu uuuu WDT uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---0 0000 uuuu uuuu 0000H uuuu uuuu uuuu uuuu WDT (Sleep/Idle) uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---u uuuu uuuu uuuu 0000H uuuu uuuu uuuu uuuu
Rev. 1.20
18
May 26, 2004
HT95LXXX
Reset Conditions Register WDTS STATUS INTC0 TMR0H TMR0L TMR0C TMR1H TMR1L TMR1C PA PAC PB PBC DialerIO PD PDC PE PEC INTC1 TBHP DTMFC DTMFD LINE RTCC MODE LCDIO LCDC PFDC PFDD PF PFC PG PGC Addr. 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 18H 19H 1AH 1BH 1EH 1FH 20H 21H 22H 24H 26H 28H 2DH 2EH 2FH 34H 35H 36H 37H Power On 0000 0111 --00 xxxx -000 0000 xxxx xxxx xxxx xxxx 00-0 1--xxxx xxxx xxxx xxxx 00-0 1--1111 1111 1111 1111 1111 1111 1111 1111 111x xxxx 1111 1111 1111 1111 ---- 1111 ---- 1111 -000 -000 --xx xxx ---- -0-1 0000 0000 0--- ---0-0- ---000- ---000- ---0000 -000 0000 ---0000 0000 1111 1111 1111 1111 ---- 1111 ---- 1111 x RES Pin 0000 0111 --uu uuuu -000 0000 xxxx xxxx xxxx xxxx 00-0 1--xxxx xxxx xxxx xxxx 00-0 1--1111 1111 1111 1111 1111 1111 1111 1111 111x xxxx 1111 1111 1111 1111 ---- 1111 ---- 1111 -000 -000 --uu uuuu ---- -0-1 0000 0000 u--- ---u-u- ---00u- ---uuu- ---uuuu -uuu 0000 ---0000 0000 1111 1111 1111 1111 ---- 1111 ---- 1111 u RES Pin (Sleep/Idle) 0000 0111 --01 uuuu -000 0000 xxxx xxxx xxxx xxxx 00-0 1--xxxx xxxx xxxx xxxx 00-0 1--1111 1111 1111 1111 1111 1111 1111 1111 111x xxxx 1111 1111 1111 1111 ---- 1111 ---- 1111 -000 -000 --uu uuuu ---- -0-1 0000 0000 u--- ---u-u- ---00u- ---uuu- ---uuuu -uuu 0000 ---0000 0000 1111 1111 1111 1111 ---- 1111 ---- 1111 u WDT 0000 0111 --1u uuuu -000 0000 xxxx xxxx xxxx xxxx 00-0 1--xxxx xxxx xxxx xxxx 00-0 1--1111 1111 1111 1111 1111 1111 1111 1111 111x xxxx 1111 1111 1111 1111 ---- 1111 ---- 1111 -000 -000 --uu uuuu ---- -0-1 0000 0000 u--- ---u-u- ---00u- ---uuu- ---uuuu -uuu 0000 ---0000 0000 1111 1111 1111 1111 ---- 1111 ---- 1111 u WDT (Sleep/Idle) uuuu uuuu --11 uuuu -uuu uuuu uuuu uuuu uuuu uuuu uu-u u--uuuu uuuu uuuu uuuu uu-u u--uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---- uuuu ---- uuuu -uuu -uuu --uu uuuu ---- -u-u uuuu uuuu u--- ---u-u- ---000- ---uuu- ---uuuu -uuu uuuu ---uuuu uuuu uuuu uuuu uuuu uuuu ---- uuuu ---- uuuu u
RAM (Data & LCD) Note: u means unchanged x means unknown - means unused
Rev. 1.20
19
May 26, 2004
HT95LXXX
Timer/Event Counter Two timer/event counters (TMR0, TMR1) are implemented in the telephone controller series. The Timer/Event Counter 0 and Timer/Event Counter 1 contain 16-bits programmable count-up counter and the clock may come from an external or internal source. For TMR0, the internal source is the instruction clock (system clock/4). For TMR1, the internal source is 32768Hz. Using the 32768Hz clock or instruction clock, there is only one reference time-base. The external clock input allows the user to count external events, measure time intervals or pulse width, or generate an accurate time base. There are 3 registers related to the Timer/Event Counter 0; TMR0H, TMR0L and TMR0C. Writing TMR0L only writes the data into a low byte buffer, but writing TMR0H simultaneously writes the data along with the contents
T im e r 0 : In s tr u c tio n c lo c k ( s y s te m T im e r 1 : 3 2 7 6 8 H z c lo c k /4 )
of the low byte buffer into the Timer/Event Counter 0 preload register (16-bit). The Timer/Event Counter 0 preload register is changed by writing TMR0H operations. Writing TMR0L will keep the Timer/Event Counter 0 preload register unchanged. Reading TMR0H latches the TMR0L into the low byte buffer to avoid a false timing problem. Reading TMR0L returns the contents of the low byte buffer. In other words, the low byte of the Timer/Event Counter 0 can not be read directly. It must read the TMR0H first to make the low byte contents of Timer/Event Counter 0 be latched into the buffer. There are 3 registers related to the Timer/Event Counter 1; TMR1H, TMR1L and TMR1C. The Timer/Event Counter 1 operates in the same manner as the Timer/Event Counter 0.
D a ta B u s T im e r /E v e n t C o u n te r 0 /1 P r e lo a d R e g is te r R e lo a d
*
IN T /T M R 1 *TM R0
T 0 M 1 /T 1 M 1 T 0 M 0 /T 1 M 0 T 0 E /T 1 E
T 0 M 1 /T 1 M 1 T 0 M 0 /T 1 M 0 T 0 O N /T 1 O N
P u ls e W id th M e a s u re m e n t M o d e C o n tro l
T im e r /e v e n t C o u n te r 0 /1
O v e r flo w to In te rru p t
N o te : * T M R 1 , T M R 0 p in a r e n o t s u p p o rte d fo r H T 9 5 L 0 0 0 /0 0 P .
Low
B y te B u ffe r
Timer/Event Counter 0/1 Register Label 3/4 Bits 0~2 R/W RO Unused bit, read as 0 To define the TMR0/TMR1 active edge of timer For event count or Timer mode (0=active on low to high; 1=active on high to low) For pulse width measurement mode (0=measures low pulse width; 1=measures high pulse width) To enable/disable timer counting (0=disabled; 1=enabled) Unused bit, read as 0 To define the operating mode Bit 7, 6=01, Event count mode (external clock) Bit 7, 6=10, Timer mode Bit 7, 6=11, Pulse width measurement mode Bit 7, 6=00, Unused Only Timer mode is available for HT95L000/00P. Function
T0E/T1E TMR0C (0EH) / TMR1C (11H)
3
RW
T0ON/T1ON 3/4
4 5
RW RO
T0M0/T1M0 T0M1/T1M1
6 7
RW
Register TMR0H (0CH) TMR0L (0DH) TMR1H (0FH) TMR1L (10H)
Bits 0~7 0~7 0~7 0~7
R/W RW RW RW RW
Function Timer/Event Counter 0 higher-order byte register Timer/Event Counter 0 lower-order byte register Timer/Event Counter 1 higher-order byte register Timer/Event Counter 1 lower-order byte register
Rev. 1.20
20
May 26, 2004
HT95LXXX
The TMR0C is the Timer/Event Counter 0 control register, which defines the Timer/Event Counter 0 options. The Timer/Event Counter 1 has the same options as the Timer/Event Counter 0 and is defined by TMR1C. The timer/event counter control registers define the operating mode, counting enable or disable and active edge. The T0M0/T1M0, T0M1/T1M1 bits define the operating mode. The event count mode is used to count external events, which means the clock source comes from an external (TMR0 or INT/TMR1) pin. The timer mode functions as a normal timer with the clock source coming from instruction clock (TMR0) or 32768Hz (TMR1). The pulse width measurement mode can be used to count the high or low level duration of the external signal (TMR0 or INT/TMR1). The counting is based on the 32768Hz clock for TMR1 or instruction clock for TMR0. In the event count or timer mode, once the timer/event counter starts counting, it will count from the current contents in the timer/event counter to FFFFH. If an overflow occurs, the counter is reloaded from the timer/event counter preload register and generates the corresponding interrupt request flag (T0F/T1F) at the same time. Note that the event count mode is not available for HT95L000/00P. I n p u ls e w i dt h m e a s ur e m e n t m ode w i t h t h e T0ON/T1ON and T0E/T1E bits equal to 1, once the TMR0/TMR1 pin has received a transient from low to high (or high to low; if the T0E/T1E bit is 0) it will start counting until the TMR0/TMR1 pin returns to the original level and resets the T0ON/T1ON. The measured result will remain in the timer/event counter even if the activated transient occurs again. In other words, only 1 cycle measurement can be done. Until setting the T0ON/T1ON, the cycle measurement will function again as long as it receives further transient pulse. Note that, in this operating mode, the timer/event counter starts counting not according to the logic level but according to the transient edges. In the case of counter overflows, the counter is reloaded from the timer/event counter preload register and continue to measure the width and issues the interrupt request just like the other two modes. Note that this mode is not available for HT95L000/00P. To enable the counting operation, the timer on bit (T0ON/T1ON) should be set to 1. In the pulse width measurement mode, the T0ON/T1ON will be cleared automatically after the measurement cycle is completed. But in the other two modes the T0ON/T1ON can only be reset by instruction. The overflow of the timer/event counter is one of the wake-up sources. No matter what the operation mode is, writing a 0 to ET0I/ET1I can disable the corresponding interrupt service. In the case of timer/event counter off condition, writing data to the timer/event counter preload register also reloads that data to the timer/event counter. But if the timer/event counter is turned on, data written to the timer/event counter is reserved only in the timer/event counter preload register. The timer/event counter will go on operating until an overflow occurs. Input/Output Ports There is a maximum of 40 bidirectional input/output lines in the HT95LXXX family MCU, labeled as PA, PB, PD, PE, PF and PG. All of these I/O ports can be used for input and output operations. For input operation, these ports are non-latching, that is, the inputs must be ready at the T2 rising edge of instruction "MOV A,[m]" (m=12H, 14H, 18H, 1AH, 34H or 36H). For output operation, all the data is latched and remains unchanged until the output latch is rewritten. Each I/O line has its own control register (PAC, PBC, PDC, PEC, PFC, PGC) to control the input/output configuration. With this control register, CMOS output or Schmitt trigger input can be reconfigured dynamically under software control. To make one I/O line to function as an input line, the corresponding latch of the control register must be written with a 1. The pull-high resistance shows itself automatically if the pull-high option is selected. The input source also depends on the control register. If the control register bit is 1, the input will read the pad state. If the control register bit is 0, the contents of the latches will move to the internal bus. The latter is possible in the read-modify-write instruction. For output function, CMOS is the only configuration. Each bit of these input/output latches can be set or cleared by SET [m].i and CLR [m].i (m=12H, 14H, 18H, 1AH, 34H or 36H) instructions. Some instructions first input data and then follow the output operations. For example, SET [m].i, CLR [m].i, CPL [m], CPLA [m] read the entire port states into the CPU, execute the defined operations (bit-operation), and then write the results back to the latches or the accumulator. Each line of port A has the capability of waking-up the device. They are selected by mask option per bit. There is a pull-high option available for all I/O lines. Once the pull-high option of an I/O line is selected, the I/O lines have pull-high resistor. Otherwise, the pull-high resistor is absent. It should be noted that a non-pull-high I/O line operating in input mode may cause a floating state.
Rev. 1.20
21
May 26, 2004
HT95LXXX
I/O port pull-high, wake-up function are selected by mask option I/O Port PA7~PA0 PB7~PB0 PD7~PD0 PE3~PE0 PF7~PF0 PG3~PG0 Output CMOS CMOS CMOS CMOS CMOS CMOS Input Supported for HT95LXXX
Pull-high Resistor Wake-up Function 400/40P 300/30P 200/20P 100/10P 000/00P Selected per bit Selected per bit Selected per nibble Selected per nibble Selected per nibble Selected per nibble Selected per bit 3/4 3/4 3/4 3/4 3/4 O O O O O O O O O O 3/4 3/4 O O O O 3/4 3/4 O O 3/4 O 3/4 3/4 O * 3/4 O 3/4 3/4
Note: 3/4 means unavailable
V C o n tr o l B it D a ta B u s D CK W r ite C o n tr o l R e g is te r C h ip R e s e t R e a d C o n tr o l R e g is te r Q QB S A ll I/O D a ta B it Q D CK QB S P in s PU
DD
W r ite D a ta R e g is te r
M U R e a d D a ta R e g is te r S y s te m W a k e -u p ( P A o n ly )
X P A W a k e - u p O p tio n 0 ~ 7
Input/Output Ports Some input/output pins can be optioned to LCD outputs by software. Register Bits R/W Label Value 5 LCDIO (28H) RW SPE0 0 1 0 1 0 1 0 1 400/40P 300/30P 200/20P 3/4 3/4 3/4 3/4 3/4 3/4 COM7~COM0 PD7~PD0 100/10P 000/00P
SEG47~SEG44 PE3~PE0 SEG43~SEG40 PD7~PD4 SEG39~SEG36 PD3~PD0 COM7~COM0 COM7~COM0 are unavailable
SEG19~SEG16 SEG15~SEG12 PE3~PE0 3/4 3/4 3/4 3/4 3/4 3/4 PE3~PE0 3/4 3/4 3/4 3/4 3/4 3/4
7
RW SPD1
6 LCDC (2DH)
RW SPD0
1
RW VBIAS
When the PD0~PD7 or the PE0~PE3 are not selected, the I/O port control register PDC (19H), PEC (1BH) could be readable/writable and be used as a general user RAM, but this function is not available for register PD (18H) and PE (1AH).
Rev. 1.20
22
May 26, 2004
HT95LXXX
DTMF Generator The DTMF (Dual Tone Multiple-Frequency) signal generator is implemented in the telephone controller. It can generate 16 dual tones and 8 single tones from the DTMF pin. This generator also supports power down, tone on/off function. The DTMF generator clock source is 3.58MHz, before using this function, the system operation mode must be at Normal mode. The power down mode (D_PWDN=1) will terminate all the DTMF generator function, however, the registers DTMFC and DTMFD are accessible at this power down mode. The duration of DTMF output should be handled by the software. DTMFD register value could be changed as desired, the DTMF pin will output the new dual-tone simultaneously. Register Label D_PWDN 3/4 TONE 3/4 3/4 3/4 3/4 3/4 DTMFD (21H) TC4~TC1 TR4~TR1 Bits 0 1 2 3 4 5 6 7 3~0 7~4 R/W RW RO RW RW RW RO RW RO RW RW Function DTMF generator power down 1: DTMF generator is at power down mode. 0: DTMF generator is at operation mode. Unused bit, read as 0 Tone output enable 1: DTMF signal output is enabled. 0: DTMF signal output is disabled. Reserved, inhibit using. Reserved, inhibit using. Unused bit, read as 0 Reserved, inhibit using. Unused bit, read as 0 To set high group frequency To set low group frequency
DTMFC (20H)
Note: Bit3, 4, 6 of DTMFC are reserved, always keep the initial value. The DTMF pin output is controlled by the combination of the D_PWDN, TONE, TR~TC value. Control Register Bits D_PWDN 1 0 0 0
D_PD W N=1
TONE x 0 1 1
TR4~TR1/TC4~TC1 x x 0 Any valid value
DTMF Pin Output Status 0 1/2 VDD 1/2 VDD 16 dual tones or 8 signal tones, bias with 1/2 VDD
D_PD W N=0
1 /2 V D D TO NE=0
TO NE=1
TO NE=0
TO NE=1
TO NE=1
TO NE=0
A ll th e tim in g o f th e T O N E = 1 a n d T O N E = 0 a r e d e te r m in e d b y s o ftw a r e
DTMF Output Tone frequency Output Frequency (Hz) Specified 697 770 852 941 1209 1336 1477 Actual 699 766 847 948 1215 1332 1472 % Error +0.29% -0.52% -0.59% +0.74% +0.50% -0.30% -0.34%
% Error does not contain the crystal frequency shift Rev. 1.20 23 May 26, 2004
HT95LXXX
DTMF frequency selection table: register DTMFD[21H] Low Group TR4 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 TR3 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 TR2 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 TR1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 TC4 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 High Group TC3 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 TC2 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 TC1 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 DTMF Output Low 697 697 697 697 770 770 770 770 852 852 852 852 941 941 941 941 High 1209 1336 1477 1633 1209 1336 1477 1633 1209 1336 1477 1633 1209 1336 1477 1633 DTMF Code 1 2 3 A 4 5 6 B 7 8 9 C * 0 # D
Single tone for testing only 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 697 770 852 941 1209 1336 1477 1633
Writing other values to TR4~TR1, TC4~TC1 may generate an unpredictable tone.
Rev. 1.20
24
May 26, 2004
HT95LXXX
Dialer I/O Function A special dialer I/O circuit is built into the telephone controller for dialing application. These specially designed I/O cells allows the controller to work under a low voltage condition that usually happens when the subscribers loop is long. Dialer I/O pin function: Name XMUTE I/O NMOS Output Description XMUTE pin output is controlled by software. This is an NMOS open drain structure pulled to VSS during dialing signal transmission. Otherwise, it is an open circuit. XMUTE is used to mute the speech circuit when transmitting the dialer signal. DNPO pin is an NMOS output, usually by means of software to make/break the line. This pin is only controlled by software. This pin is controlled by the HKS, HFI and HDI pins. When PO pin is high, the telephone line is make. When PO pin is low, the telephone line is break. This pin controls the PO pin directly. This pin is used to monitor the status of the hook-switch and its combination with HFI/HDI can control the PO pin output to make or break the line. A rising edge to HKS pin will cause the dialer I/O to be on-hook status and generate an interrupt, its vector is 18H. A falling edge to HKS pin will cause the dialer I/O to be off-hook status and clear HFO and HDO flags to 0. This falling edge will also generate an interrupt, its vector is 18H. Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P This pin is controlled directly by HDI, HKS and HFI pin. When HDO pin is high, the hold-line function is enabled and PO outputs a high signal to make the line. Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P A low pulse to HDI pin (hold-line function request) will clear HFO to 0 and toggle HDO and generates an interrupt, its vector is 18H. This pin controls the HFO and HDO pins directly. This pin is functional only when the line is made, that is, off-hook or hand-free (PO output high signal). This pin is controlled directly by HFI, HDI and HKS pins. When HFO pin is high, the hand-free function is enabled and PO outputs a high signal to make the line. A high pulse to HFI pin (hand-free function request) will clear HDO to 0 and toggle HFO and generates an interrupt, its vector is 18H. This pin controls the PO, HFO and HDO pins directly.
DNPO
NMOS Output
PO
CMOS Output
HKS
Schmitt Trigger Input
HDO
CMOS Output
HDI
Schmitt Trigger Input
HFO
CMOS Output
HFI
Schmitt Trigger Input
The following are the recommended circuit for HFI and HDI pins.
V
DD
10kW H F I P in 0 .1 m F In te r n a l P u ll- lo w 200kW 10kW 0 .1 m F H D I P in
V
DD
In te r n a l P u ll- h ig h 2 0 0 k W
Rev. 1.20
25
May 26, 2004
HT95LXXX
Phone controller also supports the dialer I/O flag to monitor the dialer status. Register Label HFI HFO Bits R/W 0 1 1: The HFI pin level is 1. RO 0: The HFI pin level is 0. RO 1: The HFO pin level is 1. 0: The HFO pin level is 0. Function
HDI
2
Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P RO 1: The HDI pin level is 1. 0: The HDI pin level is 0. Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P RO 1: The HDO pin level is 1. 0: The HDO pin level is 0. RO RW RW RW 1: The HKS pin level is 1. 0: The HKS pin level is 0. 1: The PO pin is controlled by the combination of the HKS, HFI and HDI pin. 0: The PO pin level is set to 0 by software. 1: The DNPO pin level is set to floating by software. 0: The DNPO pin level is set to 0 by software. 1: The XMUTE pin is set to floating by software. 0: The XMUTE pin is set to 0 by software.
DIALERIO (16H)
HDO
3
HKS SPO SDNPO XMUTE
4 5 6 7
The SPO flag is special designed to control the PO. When the flag SPO is set to 1, the PO pin is controlled by the combination of the HKS pin, HFI pin and HDI pin. The PO pin will always be 0 if the flag SPO=0. The relation between the Dialer I/O function (SPO=1) Dialer Function On-hook On-hook & Hand-free On-hook & Hold-line Off-hook Off-hook & Hand-free Off-hook & Hold-line Dialer I/O Pin (Flag) Status HKS 1 1 1 0 0 0 HFO 0 1 0 0 1 0 HDO 0 0 1 0 0 1 PO 0 1 1 1 1 1 DNPO floating floating floating floating floating floating Result Telephone Line break make make make make make
The following describes the dialer I/O function status machine figure (Available on Normal mode, Green mode or Sleep mode): Off-hook: A falling edge to HKS pin
HDI O n -h o o k HFI O ff-h o o k H a n d -fre e HFI HDI HDI O ff-h o o k H o ld - lin e O n -h o o k O n -h o o k HFI O ff-h o o k O ff-h o o k O n -h o o k H o ld - lin e HDI HFI HDI O ff-h o o k O n -h o o k O ff-h o o k
On-hook: A rising edge to HKS pin HFI: A high pulse to HFI pin (Hand-free request is generated.) HDI: A low pulse to HDI pin (Hold-line request is generated.)
O n -h o o k H a n d -fre e
Note: 1. If the dialer status is on-hook and hold-line, the falling edge transition onto HDI pin will not generate the dialer I/O interrupt. 2. Dialer I/O function is not available in Idle mode
Rev. 1.20
26
May 26, 2004
HT95LXXX
Line Control Function (Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P) Register LINE (22H) Label 3/4 LINEC Bits 6~0 7 R/W RO RW Unused bit, read as 0 1: Enable the line control function 0: Disable the line control function Function
The line control function is enabled by flag LINEC Conditions LINEC 1 1 1 Operation Mode Normal or Green mode Sleep mode Idle mode Source to Enable Line Control Function RTC time out interrupt Port A wake-up RTC time out interrupt Port A wake-up
When the line control source is activated, the PO pin will be set to high signal. Clearing LINEC to 0 will terminate the line control function and drive PO pin outputs low signal.
RTC In te rru p t L in e C o n tr o l C ir c u it PO =1
P o r t A W a k e - u p F u n c tio n
L IN E C = 1
RTC Function Register Label 3/4 RTCC (24H) RTCEN RTCTO Bits 6, 4~0 5 7 R/W RO RW RW Unused bit, read as 0 1: Enable RTC function 0: Disable RTC function 1: RTC time-out occurs 0: RTC time-out not occurs Function
The real time clock (RTC) is used to supply a regular internal interrupt. Its time-out period is 1000ms. If the RTC time-out occurs, the interrupt request flag RTCF and the RTCTO flag will be set to 1. The interrupt vector for the RTC is 14H. When the interrupt subroutine is serviced, the interrupt request flag (RTCF) will be cleared to 0, but the flag RTCTO remain in its original value. If the RTCTO flag is not cleared, next RTC time-out interrupt will occur. Low Battery Detection (Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P) The phone controller provides a circuit that detects the LBIN pin voltage level. To enable this detection function, the LBEN should be written as 1. Once this function is enabled, the detection circuit needs 50ms to be stable. After that, the user could read the result from LBFG. The low battery detect function will consume power. For power saving, write 0 to LBEN if the low battery detection function is unnecessary.
V R
1
DET
1 .1 5 V R e fe r e n c e V o lta g e
LBFG
2
R
L B IN LBEN
The battery low threshold is determined by external R1 and R2 resistors. 1.15= VDETxR2 1.15x(R1+ R2) (R) VDET= R1+ R2 R2
If we want to detect VDET=2.4V then 2.4V= 1.15x(R1+ R2) (R) R1=1.087R2 R2
Rev. 1.20
27
May 26, 2004
HT95LXXX
LCD Driver The LCD driver can directly drive an LCD panel with 1/8 duty and 1/4 bias or with 1/16 duty and 1/5 bias, this function is selected by the flag VBIAS. The frame of this LCD driver may select a 64Hz or 128Hz by flag FRAME. LCD driver uses the voltage of the VLCD pin as the power source. To adjust the view angle, the programmer can select the real LCD power by the flags VCON0 and VCON1. The flag LCDON is used to turn On/Off the LCD display. Note that the VLCD voltage must equal or be less than VDD. Segment/Common to I/O Selection For the flexible purpose, some of the LCD COMMON and SEGMENT pins are shared with the input/output port. Both of the HT95L400/40P and HT95L300/30P provide 12 pins to be selected to SEGMENT output pins or I/O pins. HT95L200/20P provides 8 pins to be selected for COMMON output pins or I/O pins. Both of the HT95L100/10P and HT95L000/00P provide 4 pins to be selected for SEGMENT output pins or I/O pins. All of the HT95L400/40P, HT95L300/30P and HT95L200/20P provide the LCD COMMON output pins for 8 COMMON or 16 COMMON. The description of the relation between segment pins, common pins and I/O pins are shown on the below. Register Label Bits R/W Function
FRAME
0
Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P LCD frame selection RW 0: LCD frame is 64Hz 1: LCD frame is 128Hz The frame frequency is fixed to 64Hz for HT95L100/10P and HT95L000/00P Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P LCD BIAS selection 0: select 1/16 duty and 1/5 bias, COM15~COM0 are available 1: select 1/8 duty and 1/4 bias, only COM15~COM8 are available RW When the 8 COM is selected HT95L400/40P: COM7~COM0 will be optioned to unused pins HT95L300/30P: COM7~COM0 will be optioned to unused pins HT95L200/20P: COM7~COM0 are disabled, PD7~PD0 are available Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P Low battery detection switch RW 0: disable the low battery detection 1: enable the low battery detection RO Unused bit, read as 0 Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P Low battery detection flag ROS 1: LBIN pin voltage is less than 1.15V 0: LBIN pin voltage is not less than 1.15V LCD contrast adjusting Bit6,5=00: LCD voltage supply is 0.66VLCD RW Bit6,5=10: LCD voltage supply is 0.82VLCD Bit6,5=01: LCD voltage supply is 0.93VLCD Bit6,5=11: LCD voltage supply is 1.00VLCD RW 1: Turn on the LCD display 0: Turn off the LCD display
VBIAS
1
LCDC (2DH)
LBEN
2
3/4
3
LBFG
4
VCON0 VCON1
5 6
LCDON
7
Rev. 1.20
28
May 26, 2004
HT95LXXX
Register Label 3/4 Bits R/W 0~4 RO Unused bit, read as 0 Supported for HT95L400/40P, HT95L300/30P, HT95L100/10P, HT95L000/00P Bit value is 0: HT95L400/40P: SEG47~SEG44 output are available HT95L300/30P: SEG47~SEG44 output are available HT95L100/10P: SEG19~SEG16 output are available RW HT95L000/00P: SEG15~SEG12 output are available Bit value is 1: HT95L400/40P: PE3~PE0 output are available HT95L300/30P: PE3~PE0 output are available HT95L100/10P: PE3~PE0 output are available HT95L000/00P: PE3~PE0 output are available Supported for HT95L400/40P, HT95L300/30P RW Bit value is 0: SEG39~SEG36 output are available Bit value is 1: PD3~PD0 output are available Supported for HT95L400/40P, HT95L300/30P RW Bit value is 0: SEG43~SEG40 output are available Bit value is 1: PD7~PD4 output are available Function
SPE0 LCDIO (28H)
5
SPD0
6
SPD1
7
LCD Display Memory The phone controller provides an area on embedded data memory for LCD display. The LCD display memory are located at bank 1BH and can be read and written to, only by indirect addressing mode using MP1. When data is written into the display data area it is automatically read by the LCD driver which then generates the corresponding LCD driving signals, to turn the display On or Off, a 1 or 0 is written to the corresponding bit of the display memory, respectively. All of the LCD display memories are with random values after the power on reset and unchanged after other reset conditions. COM7 to COM0 for HT95L400/40P, HT95L300/30P Address 40H 41H 3/4 6EH 6FH Register Name SEG0 SEG1 3/4 SEG46 SEG47 Bit 7 COM7 COM7 COM7 COM7 COM7 Bit 6 COM6 COM6 COM6 COM6 COM6 Bit 5 COM5 COM5 COM5 COM5 COM5 Bit 4 COM4 COM4 COM4 COM4 COM4 Bit 3 COM3 COM3 COM3 COM3 COM3 Bit 2 COM2 COM2 COM2 COM2 COM2 Bit 1 COM1 COM1 COM1 COM1 COM1 Bit 0 COM0 COM0 COM0 COM0 COM0
COM15 to COM8 for HT95L400/40P, HT95L300/30P Address 70H 71H 3/4 9EH 9FH Register Name SEG0 SEG1 3/4 SEG46 SEG47 Bit 7 COM15 COM15 COM15 COM15 COM15 Bit 6 COM14 COM14 COM14 COM14 COM14 Bit 5 COM13 COM13 COM13 COM13 COM13 Bit 4 COM12 COM12 COM12 COM12 COM12 Bit 3 COM11 COM11 COM11 COM11 COM11 Bit 2 COM10 COM10 COM10 COM10 COM10 Bit 1 COM9 COM9 COM9 COM9 COM9 Bit 0 COM8 COM8 COM8 COM8 COM8
Note: When VBIAS bit set to 1 for 8 COM operation (488), the LCD RAM only map to (70H~9FH).
Rev. 1.20
29
May 26, 2004
HT95LXXX
COM7 to COM0 for HT95L200/20P Address 40H 41H 3/4 56H 57H Register Name SEG0 SEG1 3/4 SEG22 SEG23 Bit 7 COM7 COM7 COM7 COM7 COM7 Bit 6 COM6 COM6 COM6 COM6 COM6 Bit 5 COM5 COM5 COM5 COM5 COM5 Bit 4 COM4 COM4 COM4 COM4 COM4 Bit 3 COM3 COM3 COM3 COM3 COM3 Bit 2 COM2 COM2 COM2 COM2 COM2 Bit 1 COM1 COM1 COM1 COM1 COM1 Bit 0 COM0 COM0 COM0 COM0 COM0
COM15 to COM8 for HT95L200/20P Address 70H 71H 3/4 86H 87H Register Name SEG0 SEG1 3/4 SEG22 SEG23 Bit 7 COM15 COM15 COM15 COM15 COM15 Bit 6 COM14 COM14 COM14 COM14 COM14 Bit 5 COM13 COM13 COM13 COM13 COM13 Bit 4 COM12 COM12 COM12 COM12 COM12 Bit 3 COM11 COM11 COM11 COM11 COM11 Bit 2 COM10 COM10 COM10 COM10 COM10 Bit 1 COM9 COM9 COM9 COM9 COM9 Bit 0 COM8 COM8 COM8 COM8 COM8
Note: When VBIAS bit is set to 1 for 8 COM operation (248), the LCD RAM only map to (70H~87H). COM7 to COM0 for HT95L100/10P Address 8CH 8DH 3/4 9EH 9FH Register Name SEG0 SEG1 3/4 SEG18 SEG19 Bit 7 COM7 COM7 COM7 COM7 COM7 Bit 6 COM6 COM6 COM6 COM6 COM6 Bit 5 COM5 COM5 COM5 COM5 COM5 Bit 4 COM4 COM4 COM4 COM4 COM4 Bit 3 COM3 COM3 COM3 COM3 COM3 Bit 2 COM2 COM2 COM2 COM2 COM2 Bit 1 COM1 COM1 COM1 COM1 COM1 Bit 0 COM0 COM0 COM0 COM0 COM0
COM7 to COM0 for HT95L000/00P Address 90H 91H 3/4 9EH 9FH Register Name SEG0 SEG1 3/4 SEG14 SEG15 Bit 7 COM7 COM7 COM7 COM7 COM7 Bit 6 COM6 COM6 COM6 COM6 COM6 Bit 5 COM5 COM5 COM5 COM5 COM5 Bit 4 COM4 COM4 COM4 COM4 COM4 Bit 3 COM3 COM3 COM3 COM3 COM3 Bit 2 COM2 COM2 COM2 COM2 COM2 Bit 1 COM1 COM1 COM1 COM1 COM1 Bit 0 COM0 COM0 COM0 COM0 COM0
PFD Generator (Supported for HT95L400/40P, HT95L300/30P, HT95L200/20P, HT95L100/10P) Register Label 3/4 PFDEN PFDC (2EH) Bits 3~0 4 R/W RO RW Unused bit, read as 0 1: Enable PFD output 0: Disable PFD output, the MUSIC pin output low level. Bit6, 5=00: Prescaler output= PFD frequency source/1 Bit6, 5=01: Prescaler output= PFD frequency source/2 Bit6, 5=10: Prescaler output= PFD frequency source/4 Bit6, 5=11: Prescaler output= PFD frequency source/8 1: The PFD frequency source is 3.58MHz/4 0: The PFD frequency source is 32768Hz PFD data register Function
PRES0 PRES1
5 6
RW
FPFD PFDD (2FH) 3/4
7 7~0
RW RW
Rev. 1.20
30
May 26, 2004
HT95LXXX
The PFD (programmable frequency divider) is implemented in the phone controller. It is composed of two portions: a prescaler and a general counter. The prescaler is controlled by the register bits, PRES0 and PRES1. The general counter is programmed by an 8-bit register PFDD. The source for this generator can be selected from 3.58MHz/4 or 32768Hz. To enable the PFD output, write 1 to the PFDEN bit. The PFDD is inhibited to write while the PFD is disabled. To modify the PFDD contents, the PFD must be enabled. When the generator is disabled, the PFDD is cleared by hardware.
P r e s c a le r O u tp u t PFD O u tp u t
32768H z 3 .5 8 M H z /4
P r e s c a le r
PFDD C le a r
M U S IC
PR ES1,PR ES0
PFDEN
PFDEN
Prescaler output , where N=the value of the PFDD PFD output frequency= 2x(N + 1) Mask Option Table The following shows many kinds of mask options in the telephone controller. All these options should be defined in order to ensure proper system functions. Name Mask Option WDT source selection RC(R)Select the WDT OSC to be the WDT source. T1(R)Select the instruction clock to be the WDT source. 32kHz(R)Select the external 32768Hz to be the WDT source. Disable(R)Disable WDT function. This option defines how to clear the WDT by instruction. One clear instruction(R)The CLR WDT can clear the WDT. Two clear instructions(R)Only when both of the CLR WDT1 and CLR WDT2 have been executed, then WDT can be cleared. Port A wake-up selection. Define the activity of wake-up function. All port A have the capability to wake-up the chip from a HALT. This wake-up function is selected per bit. Pull-high option. This option determines whether the pull-high resistance is viable or not. Port A pull-high option is selected per bit. Port B pull-high option is selected per bit. Port D pull-high option is selected per nibble. (Note: Port D pull-high option is selected per byte for HT95L200/20P.) Port E pull-high option is selected per nibble. Port F pull-high option is selected per nibble. Port G pull-high option is selected per nibble.
WDT
CLRWDT
Wake-up PA
Pull-high PA Pull-high PB Pull-high PD Pull-high PE Pull-high PF Pull-high PG
Rev. 1.20
31
May 26, 2004
HT95LXXX
Application Circuits
22M W T ip O ff-h o o k A92 R in g 100kW 10mF 3 .3 k W A42 100kW 47kW H a n d fre e 0 .0 2 m F 10kW 270kW V 5 .1 V 0 .1 m F 100mF V
DD
100kW O n -h o o k 330kW 1N4148 2 .2 k W 220kW 1mF 1N4148 1N4148
1N4148
220kW 33kW
1 .5 k W 220kW 1mF
150kW
S peech N e tw o rk 100kW
B a tte ry 1 .5 3 = 4 .5 V
DD
0 .1 m F
HFI I/O
PO
HDO
HDI
VDD
HKS
HFO
DTM F XM UTE M U S IC V
DD
0 .1 m F
VLCD RES
100kW 0 .1 m F
H T95LXXX
V
DD
L B IN
MEMORY D IA L IN G
STORE HOLD
AM PM
ABR
MON
TUE
W ED
THR
FRI
SAT
SUN
COMMON
SEGMENT LCD Pannel I/O I/O X1 X2 XC 15kW 1 4 7 * /T 0 # 8 9 5 6 2 3 K ey1 K ey2 K ey3 K ey4 K ey5 K ey6 K ey7 K ey8 K ey9 K ey10 K ey11 K ey12 32768H z 3nF 50nF VSS
K e y M a tr ix
Note: Some floating input pins (INT/TMR1, TMR0, etc.) are not shown in this circuit.
Rev. 1.20
32
May 26, 2004
HT95LXXX
Instruction Set Summary
Mnemonic Arithmetic ADD A,[m] ADDM A,[m] ADD A,x ADC A,[m] ADCM A,[m] SUB A,x SUB A,[m] SUBM A,[m] SBC A,[m] SBCM A,[m] DAA [m] Add data memory to ACC Add ACC to data memory Add immediate data to ACC Add data memory to ACC with carry Add ACC to data memory with carry Subtract immediate data from ACC Subtract data memory from ACC Subtract data memory from ACC with result in data memory Subtract data memory from ACC with carry Subtract data memory from ACC with carry and result in data memory Decimal adjust ACC for addition with result in data memory 1 1(1) 1 1 1(1) 1 1 1(1) 1 1(1) 1(1) Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV C Description Instruction Cycle Flag Affected
Logic Operation AND A,[m] OR A,[m] XOR A,[m] ANDM A,[m] ORM A,[m] XORM A,[m] AND A,x OR A,x XOR A,x CPL [m] CPLA [m] AND data memory to ACC OR data memory to ACC Exclusive-OR data memory to ACC AND ACC to data memory OR ACC to data memory Exclusive-OR ACC to data memory AND immediate data to ACC OR immediate data to ACC Exclusive-OR immediate data to ACC Complement data memory Complement data memory with result in ACC 1 1 1 1(1) 1(1) 1(1) 1 1 1 1(1) 1 Z Z Z Z Z Z Z Z Z Z Z
Increment & Decrement INCA [m] INC [m] DECA [m] DEC [m] Rotate RRA [m] RR [m] RRCA [m] RRC [m] RLA [m] RL [m] RLCA [m] RLC [m] Data Move MOV A,[m] MOV [m],A MOV A,x Bit Operation CLR [m].i SET [m].i Clear bit of data memory Set bit of data memory 1(1) 1(1) None None Move data memory to ACC Move ACC to data memory Move immediate data to ACC 1 1(1) 1 None None None Rotate data memory right with result in ACC Rotate data memory right Rotate data memory right through carry with result in ACC Rotate data memory right through carry Rotate data memory left with result in ACC Rotate data memory left Rotate data memory left through carry with result in ACC Rotate data memory left through carry 1 1(1) 1 1(1) 1 1(1) 1 1(1) None None C C None None C C Increment data memory with result in ACC Increment data memory Decrement data memory with result in ACC Decrement data memory 1 1(1) 1 1(1) Z Z Z Z
Rev. 1.20
33
May 26, 2004
HT95LXXX
Mnemonic Branch JMP addr SZ [m] SZA [m] SZ [m].i SNZ [m].i SIZ [m] SDZ [m] SIZA [m] SDZA [m] CALL addr RET RET A,x RETI Table Read TABRDC [m] TABRDL [m] Miscellaneous NOP CLR [m] SET [m] CLR WDT CLR WDT1 CLR WDT2 SWAP [m] SWAPA [m] HALT No operation Clear data memory Set data memory Clear Watchdog Timer Pre-clear Watchdog Timer Pre-clear Watchdog Timer Swap nibbles of data memory Swap nibbles of data memory with result in ACC Enter power down mode 1 1(1) 1(1) 1 1 1 1(1) 1 1 None None None TO,PDF TO(4),PDF(4) TO(4),PDF(4) None None TO,PDF Read ROM code (current page) to data memory and TBLH Read ROM code (last page) to data memory and TBLH 2(1) 2(1) None None Jump unconditionally Skip if data memory is zero Skip if data memory is zero with data movement to ACC Skip if bit i of data memory is zero Skip if bit i of data memory is not zero Skip if increment data memory is zero Skip if decrement data memory is zero Skip if increment data memory is zero with result in ACC Skip if decrement data memory is zero with result in ACC Subroutine call Return from subroutine Return from subroutine and load immediate data to ACC Return from interrupt 2 1(2) 1(2) 1(2) 1(2) 1(3) 1(3) 1(2) 1(2) 2 2 2 2 None None None None None None None None None None None None None Description Instruction Cycle Flag Affected
Note: x: Immediate data m: Data memory address A: Accumulator i: 0~7 number of bits addr: Program memory address O: Flag is affected -: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle (four system clocks). : If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more cycle (four system clocks). Otherwise the original instruction cycle is unchanged. : and (2)
(2)
(3) (1) (4)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the CLR WDT1 or CLR WDT2 instruction, the TO and PDF are cleared. Otherwise the TO and PDF flags remain unchanged.
Rev. 1.20
34
May 26, 2004
HT95LXXX
Instruction Definition
ADC A,[m] Description Operation Affected flag(s) TO 3/4 ADCM A,[m] Description Operation Affected flag(s) TO 3/4 ADD A,[m] Description Operation Affected flag(s) TO 3/4 ADD A,x Description Operation Affected flag(s) TO 3/4 ADDM A,[m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O Add data memory and carry to the accumulator The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator. ACC ACC+[m]+C
Add the accumulator and carry to data memory The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory. [m] ACC+[m]+C
Add data memory to the accumulator The contents of the specified data memory and the accumulator are added. The result is stored in the accumulator. ACC ACC+[m]
Add immediate data to the accumulator The contents of the accumulator and the specified data are added, leaving the result in the accumulator. ACC ACC+x
Add the accumulator to the data memory The contents of the specified data memory and the accumulator are added. The result is stored in the data memory. [m] ACC+[m]
Rev. 1.20
35
May 26, 2004
HT95LXXX
AND A,[m] Description Operation Affected flag(s) TO 3/4 AND A,x Description Operation Affected flag(s) TO 3/4 ANDM A,[m] Description Operation Affected flag(s) TO 3/4 CALL addr Description PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 Logical AND accumulator with data memory Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator. ACC ACC AND [m]
Logical AND immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical_AND operation. The result is stored in the accumulator. ACC ACC AND x
Logical AND data memory with the accumulator Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory. [m] ACC AND [m]
Subroutine call The instruction unconditionally calls a subroutine located at the indicated address. The program counter increments once to obtain the address of the next instruction, and pushes this onto the stack. The indicated address is then loaded. Program execution continues with the instruction at this address. Stack PC+1 PC addr
Operation Affected flag(s)
TO 3/4 CLR [m] Description Operation Affected flag(s) TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Clear data memory The contents of the specified data memory are cleared to 0. [m] 00H
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.20
36
May 26, 2004
HT95LXXX
CLR [m].i Description Operation Affected flag(s) TO 3/4 CLR WDT Description Operation Affected flag(s) TO 0 CLR WDT1 Description PDF 0 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Clear bit of data memory The bit i of the specified data memory is cleared to 0. [m].i 0
Clear Watchdog Timer The WDT is cleared (clears the WDT). The power down bit (PDF) and time-out bit (TO) are cleared. WDT 00H PDF and TO 0
Preclear Watchdog Timer Together with CLR WDT2, clears the WDT. PDF and TO are also cleared. Only execution of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged. WDT 00H* PDF and TO 0*
Operation Affected flag(s)
TO 0* CLR WDT2 Description
PDF 0*
OV 3/4
Z 3/4
AC 3/4
C 3/4
Preclear Watchdog Timer Together with CLR WDT1, clears the WDT. PDF and TO are also cleared. Only execution of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged. WDT 00H* PDF and TO 0*
Operation Affected flag(s)
TO 0* CPL [m] Description Operation Affected flag(s) TO 3/4
PDF 0*
OV 3/4
Z 3/4
AC 3/4
C 3/4
Complement data memory Each bit of the specified data memory is logically complemented (1s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. [m] [m]
PDF 3/4
OV 3/4
Z O
AC 3/4
C 3/4
Rev. 1.20
37
May 26, 2004
HT95LXXX
CPLA [m] Description Complement data memory and place result in the accumulator Each bit of the specified data memory is logically complemented (1s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. The complemented result is stored in the accumulator and the contents of the data memory remain unchanged. ACC [m]
Operation Affected flag(s)
TO 3/4 DAA [m] Description
PDF 3/4
OV 3/4
Z O
AC 3/4
C 3/4
Decimal-Adjust accumulator for addition The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored in the data memory and only the carry flag (C) may be affected. If ACC.3~ACC.0 >9 or AC=1 then [m].3~[m].0 (ACC.3~ACC.0)+6, AC1=AC else [m].3~[m].0 (ACC.3~ACC.0), AC1=0 and If ACC.7~ACC.4+AC1 >9 or C=1 then [m].7~[m].4 ACC.7~ACC.4+6+AC1,C=1 else [m].7~[m].4 ACC.7~ACC.4+AC1,C=C
Operation
Affected flag(s) TO 3/4 DEC [m] Description Operation Affected flag(s) TO 3/4 DECA [m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Decrement data memory Data in the specified data memory is decremented by 1. [m] [m]-1
Decrement data memory and place result in the accumulator Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. ACC [m]-1
Rev. 1.20
38
May 26, 2004
HT95LXXX
HALT Description Enter power down mode This instruction stops program execution and turns off the system clock. The contents of the RAM and registers are retained. The WDT and prescaler are cleared. The power down bit (PDF) is set and the WDT time-out bit (TO) is cleared. PC PC+1 PDF 1 TO 0
Operation
Affected flag(s) TO 0 INC [m] Description Operation Affected flag(s) TO 3/4 INCA [m] Description Operation Affected flag(s) TO 3/4 JMP addr Description Operation Affected flag(s) TO 3/4 MOV A,[m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Directly jump The program counter are replaced with the directly-specified address unconditionally, and control is passed to this destination. PC addr PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 1 OV 3/4 Z 3/4 AC 3/4 C 3/4
Increment data memory Data in the specified data memory is incremented by 1 [m] [m]+1
Increment data memory and place result in the accumulator Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. ACC [m]+1
Move data memory to the accumulator The contents of the specified data memory are copied to the accumulator. ACC [m]
Rev. 1.20
39
May 26, 2004
HT95LXXX
MOV A,x Description Operation Affected flag(s) TO 3/4 MOV [m],A Description Operation Affected flag(s) TO 3/4 NOP Description Operation Affected flag(s) TO 3/4 OR A,[m] Description Operation Affected flag(s) TO 3/4 OR A,x Description Operation Affected flag(s) TO 3/4 ORM A,[m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 No operation No operation is performed. Execution continues with the next instruction. PC PC+1 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Move immediate data to the accumulator The 8-bit data specified by the code is loaded into the accumulator. ACC x
Move the accumulator to data memory The contents of the accumulator are copied to the specified data memory (one of the data memories). [m] ACC
Logical OR accumulator with data memory Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator. ACC ACC OR [m]
Logical OR immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical_OR operation. The result is stored in the accumulator. ACC ACC OR x
Logical OR data memory with the accumulator Data in the data memory (one of the data memories) and the accumulator perform a bitwise logical_OR operation. The result is stored in the data memory. [m] ACC OR [m]
Rev. 1.20
40
May 26, 2004
HT95LXXX
RET Description Operation Affected flag(s) TO 3/4 RET A,x Description Operation Affected flag(s) TO 3/4 RETI Description Operation Affected flag(s) TO 3/4 RL [m] Description Operation Affected flag(s) TO 3/4 RLA [m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Return from subroutine The program counter is restored from the stack. This is a 2-cycle instruction. PC Stack
Return and place immediate data in the accumulator The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data. PC Stack ACC x
Return from interrupt The program counter is restored from the stack, and interrupts are enabled by setting the EMI bit. EMI is the enable master (global) interrupt bit. PC Stack EMI 1
Rotate data memory left The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0. [m].(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 [m].7
Rotate data memory left and place result in the accumulator Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. ACC.(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 [m].7
Rev. 1.20
41
May 26, 2004
HT95LXXX
RLC [m] Description Operation Rotate data memory left through carry The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position. [m].(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 C C [m].7
Affected flag(s) TO 3/4 RLCA [m] Description PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rotate left through carry and place result in the accumulator Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored in the accumulator but the contents of the data memory remain unchanged. ACC.(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 C C [m].7
Operation
Affected flag(s) TO 3/4 RR [m] Description Operation Affected flag(s) TO 3/4 RRA [m] Description Operation Affected flag(s) TO 3/4 RRC [m] Description Operation PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rotate data memory right The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7. [m].i [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 [m].0
Rotate right and place result in the accumulator Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. ACC.(i) [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 [m].0
Rotate data memory right through carry The contents of the specified data memory and the carry flag are together rotated 1 bit right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position. [m].i [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 C C [m].0
Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rev. 1.20
42
May 26, 2004
HT95LXXX
RRCA [m] Description Rotate right through carry and place result in the accumulator Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is stored in the accumulator. The contents of the data memory remain unchanged. ACC.i [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 C C [m].0
Operation
Affected flag(s) TO 3/4 SBC A,[m] Description Operation Affected flag(s) TO 3/4 SBCM A,[m] Description Operation Affected flag(s) TO 3/4 SDZ [m] Description PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Subtract data memory and carry from the accumulator The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator. ACC ACC+[m]+C
Subtract data memory and carry from the accumulator The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory. [m] ACC+[m]+C
Skip if decrement data memory is 0 The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]-1)=0, [m] ([m]-1)
Operation Affected flag(s)
TO 3/4 SDZA [m] Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Decrement data memory and place result in ACC, skip if 0 The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. The result is stored in the accumulator but the data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]-1)=0, ACC ([m]-1)
Operation Affected flag(s)
TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.20
43
May 26, 2004
HT95LXXX
SET [m] Description Operation Affected flag(s) TO 3/4 SET [m]. i Description Operation Affected flag(s) TO 3/4 SIZ [m] Description PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Set data memory Each bit of the specified data memory is set to 1. [m] FFH
Set bit of data memory Bit i of the specified data memory is set to 1. [m].i 1
Skip if increment data memory is 0 The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]+1)=0, [m] ([m]+1)
Operation Affected flag(s)
TO 3/4 SIZA [m] Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Increment data memory and place result in ACC, skip if 0 The contents of the specified data memory are incremented by 1. If the result is 0, the next instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]+1)=0, ACC ([m]+1)
Operation Affected flag(s)
TO 3/4 SNZ [m].i Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Skip if bit i of the data memory is not 0 If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data memory is not 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m].i0
Operation Affected flag(s)
TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.20
44
May 26, 2004
HT95LXXX
SUB A,[m] Description Operation Affected flag(s) TO 3/4 SUBM A,[m] Description Operation Affected flag(s) TO 3/4 SUB A,x Description Operation Affected flag(s) TO 3/4 SWAP [m] Description Operation Affected flag(s) TO 3/4 SWAPA [m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O Subtract data memory from the accumulator The specified data memory is subtracted from the contents of the accumulator, leaving the result in the accumulator. ACC ACC+[m]+1
Subtract data memory from the accumulator The specified data memory is subtracted from the contents of the accumulator, leaving the result in the data memory. [m] ACC+[m]+1
Subtract immediate data from the accumulator The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator. ACC ACC+x+1
Swap nibbles within the data memory The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged. [m].3~[m].0 [m].7~[m].4
Swap data memory and place result in the accumulator The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged. ACC.3~ACC.0 [m].7~[m].4 ACC.7~ACC.4 [m].3~[m].0
Rev. 1.20
45
May 26, 2004
HT95LXXX
SZ [m] Description Skip if data memory is 0 If the contents of the specified data memory are 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m]=0
Operation Affected flag(s)
TO 3/4 SZA [m] Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move data memory to ACC, skip if 0 The contents of the specified data memory are copied to the accumulator. If the contents is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m]=0
Operation Affected flag(s)
TO 3/4 SZ [m].i Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Skip if bit i of the data memory is 0 If bit i of the specified data memory is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m].i=0
Operation Affected flag(s)
TO 3/4 TABRDC [m] Description Operation Affected flag(s) TO 3/4 TABRDL [m] Description Operation Affected flag(s) TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move the ROM code (current page) to TBLH and data memory The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved to the specified data memory and the high byte transferred to TBLH directly. [m] ROM code (low byte) TBLH ROM code (high byte)
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move the ROM code (last page) to TBLH and data memory The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to the data memory and the high byte transferred to TBLH directly. [m] ROM code (low byte) TBLH ROM code (high byte)
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.20
46
May 26, 2004
HT95LXXX
XOR A,[m] Description Operation Affected flag(s) TO 3/4 XORM A,[m] Description Operation Affected flag(s) TO 3/4 XOR A,x Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 Logical XOR accumulator with data memory Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator. ACC ACC XOR [m]
Logical XOR data memory with the accumulator Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected. [m] ACC XOR [m]
Logical XOR immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected. ACC ACC XOR x
Rev. 1.20
47
May 26, 2004
HT95LXXX
Package Information
56-pin SSOP (300mil) Outline Dimensions
56 A 1 C C'
29 B 28
G H a F
D E
Symbol A B C C D E F G H a
Dimensions in mil Min. 395 291 8 720 89 3/4 4 25 4 0 Nom. 3/4 3/4 3/4 3/4 3/4 25 3/4 3/4 3/4 3/4 Max. 420 299 12 730 99 3/4 10 35 12 8
Rev. 1.20
48
May 26, 2004
HT95LXXX
64-pin QFP (1420) Outline Dimensions
C D 51 33 G H
I 52 32 F A B E
64
20 K a J 1 19
Symbol A B C D E F G H I J K a
Dimensions in mm Min. 18.80 13.90 24.80 19.90 3/4 3/4 2.50 3/4 3/4 1.15 0.10 0 Nom. 3/4 3/4 3/4 3/4 1 0.40 3/4 3/4 0.10 3/4 3/4 3/4 Max. 19.20 14.10 25.20 20.10 3/4 3/4 3.10 3.40 3/4 1.45 0.20 7
Rev. 1.20
49
May 26, 2004
HT95LXXX
100-pin QFP (1420) Outline Dimensions
C D 80 51 G H
I 81 50
F A B
E
100
31 K 1 30 a J
Symbol A B C D E F G H I J K a
Dimensions in mm Min. 18.50 13.90 24.50 19.90 3/4 3/4 2.50 3/4 3/4 1 0.10 0 Nom. 3/4 3/4 3/4 3/4 0.65 0.30 3/4 3/4 0.10 3/4 3/4 3/4 Max. 19.20 14.10 25.20 20.10 3/4 3/4 3.10 3.40 3/4 1.40 0.20 7
Rev. 1.20
50
May 26, 2004
HT95LXXX
128-pin QFP (1420) Outline Dimensions
C D 102 65 G I 103 64 H
F
A B
E
128
39
K 1 38 a J
Symbol A B C D E F G H I J K a
Dimensions in mm Min. 17.00 13.90 23.00 19.90 3/4 3/4 2.50 3/4 3/4 0.65 0.10 0 Nom. 3/4 3/4 3/4 3/4 0.50 0.20 3/4 3/4 0.10 3/4 3/4 3/4 Max. 17.50 14.10 23.50 20.10 3/4 3/4 3.10 3.40 3/4 0.95 0.20 7
Rev. 1.20
51
May 26, 2004
HT95LXXX
Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031 Tel: 0755-8346-5589 Fax: 0755-8346-5590 ISDN: 0755-8346-5591 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holmate Semiconductor, Inc. (North America Sales Office) 46712 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright O 2004 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holteks products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw.
Rev. 1.20
52
May 26, 2004

▲Up To Search▲

Price & Availability of HT95A20P

	To Download HT95A20P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .