View 95011-2213-J-BLK_4875416.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

High Reliability Surface Mount Resistor
MCHP Series
* * * * * * * DESC Approved Excellent surge capability Reliable Metal GlazeTM technology Superb solderability - reflow and wave Operating temperature -55C to +150C Minimum board real estate requirements Established SPC and continuous improvement programs
Metal GlazeTM thick film element fired at 1000C to solid ceramic substrate
High temperature dielectric coating Solder over nickel barrier
The MCHP High Reliability Surface Mount Resistors are part of the RG product family of precision resistors developed by IRC in 1960 to meet the stringent demands of the military market. In leaded form, these resistors are qualified to level S under MIL-R-39017 and MIL-R-55182. The MCHP resistor utilizes the core element from this series, but with modified contacts and encapsulation.
The MCHP High Reliability Surface Mount Resistors are in compliance to DESC drawings 85083 (MCHP 1/8) and 87037 (MCHP 1) and are supplied in accordance tot he requirements of MIL-R-55342. Under this specification, all resistors are subjected to "Thermal Shock". Samples are selected from each lot and tested to "TCR", "STOL", "Terminal adhesion", "Solderability", and "Visual" to ensure the lot is in conformance to specified requirements.
Electrical Data
Size Code B D F H Industry Footprint 1206 2010 2512 3610 IRC Type MCHP 1/8 MCHP 1/2 MCHP 1 MCHP 2 DESC Drawing 950114 94048 95006
5
Rated Power (watts) 0.125 @ 70C 0.5 @ 70C 1.0 @ 70C 2.0 @ 25C
Working Voltage 200 300 350 500
Maximum Voltage 400 600 700 1000
Resistance Range (ohms) 0.1 to 1.0M 0.1 to 1.6M 0.1 to 2.2M 0.2 to 2.2M
Tolerance (%) 1, 2, 5 1, 2, 5 1, 2, 5 1, 2, 5
TCR (ppm/C) 100 100 100 100
94047
See page 8 for product dimensions, recommended solder pads, and standard packaging. For operation above 70C, use power derating curve. Not to exceed P x R 4 Formerly 85083 5 Formerly 87037
Power Derating Curve
120 100
% of Rated Power
80 60 40 20
95 00 6,
94 04 7
95 01 1,
94 04 8,
0 25 35 45 55 65 75 85 95 105 115 125 135 145 30 40 50 60 70 80 90 100 110 120 130 140 150
Ambient Temperature (C)
General Note
IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC's own data and is considered accurate at time of going to print.
(c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com
A subsidiary of TT electronics plc
MCHP Series Issue September 2008 Sheet 1 of 2
High Reliability Surface Mount Resistor
Environmental Data
Characteristics Temperature Coefficient Thermal Shock Low Temperature Operation Short Time Overload High Temperature Exposure Resistance to Bonding Exposure Solderability Moisture Resistance Life Test Terminal Adhesion Strength Resistance to Board Bending Maximum Change 100 ppm/C 0.5% + 0.01 ohm 0.25% + 0.01 ohm 0.25% + 0.01 ohm 1% for R>100K ohm 0.5% + 0.01 ohm 0.25% + 0.01 ohm 95% minimum coverage 0.5% 0.01 ohm 0.5% 0.01 ohm 1% + 0.01 ohm no mechanical damage 1% + 0.01 ohm no mechanical damage
IRC Advanced Film Division
Test Method MIL-R-55342E Par 4.7.9 (-55C + 125C) MIL-R-55342E Par 4.7.3 (-65C + 150C, 5 cycles) MIL-R-55342E Par 4.7.4 (-65C @ working voltage) MIL-R-55342E Par 4.7.5 2.5 x P x R for 5 seconds MIL-R-55342E Par 4.7.6 (+150C for 100 hours) MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260C for 10 seconds) MIL-STD-202, Method 208 (245C for 5 seconds) MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours) MIL-R-55342E Par 4.7.10 (2000 hours at 70C intermittent) 1200 gram push from underside of mounted chip for 60 seconds Chip mounted in center of 90mm long board, deflected 5mm so as to exert pull on chip contacts for 10 seconds
Ordering Data
Sample Part No. DESC Drawing Number Resistance Value
(CHP 1/8, CHP 1/2, CHP 1, or CHP 2) (100 ohms and greater - First 3 significant digits plus 4th digit multiplier) Example: 100 ohms = 1000, 1000 ohms = 1001, 150,000 ohms = 1503 (Less than 100 ohms - "R" is used to designate decimal) Example: 51 ohms = 51R0, 1.6 ohm = 1R60, 0.25 ohms = R250
95011
- 2213 - F - 13
Tolerance
(F = 1.0%; G = 2.0%; J = 5.0%)
Packaging Code*
(BLK = Bulk, 7 = 7" Reel, 13 = 13" Reel)
(c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com
MCHP Series Issue September 2008 Sheet 2 of 2

▲Up To Search▲

Price & Availability of 95011-2213-J-BLK

	To Download 95011-2213-J-BLK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .