 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Technical Data Sheet 1.8mm Round Subminiature Silicin PIN Photodiode PD42-21C/TR8 Features Fast response time High photo sensitivity Small junction capacitance Package in 12mm tape on 7" diameter reel Pb free The product itself will remain within RoHS compliant version. Descriptions PD42-21C/TR8 is a high speed and high sensitive PIN photodiode in miniature spherical top view lens SMD package and it is molded in a black plastic .The device is spectrally matched with the infrared emitting diode. Applications High speed photo detector Copier Game machine Infrared applied system Device Selection Guide LED Part No. PD Chip Material Silicon Lens Color Water clear Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 1 of 10 Prepared byJaine Tsai PD42-21C/TR8 Package Dimensions 1 Cathode 2 Anode 1 2 1 2 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions 0.1mm Absolute Maximum Ratings (Ta=25) Parameter Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature Power Dissipation at(or below) 25Free Air Temperature Symbol VR Topr Tstg Tsol Pc Rating 32 -25 ~ +85 -40 ~ +100 260 150 Units V mW Notes: *1:Soldering time5 seconds. Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 2 of 10 Prepared byJaine Tsai PD42-21C/TR8 Electro-Optical Characteristics (Ta=25) Parameter Rang Of Spectral Bandwidth Wavelength Of Peak Sensitivity Open-Circuit Voltage Symbol 0.5 P VOC ISC Condition ----Ee=5mW /cm2 P=940nm Ee=1mW /cm2 P=875nm Ee=1mW /cm2 P=875nm VR=5V Ee=0mW /cm2 VR=10V Ee=0mW /cm2 IR=100A Ee=0mW /cm2 f=1MHz VR=5V VR=10V RL=1000 Min 400 ----Typ --940 0.42 Max 1100 ----Unit nm nm V A Short-Circuit Current 2.0 5.0 12 Reverse Light Current IL ID BVR 2.0 5.0 12 A Dark Current Reverse Breakdown Voltage --32 --170 10 --- nA V Total Capacitance Rise Time Fall Time Ct tr tf ------- 5 6 6 ----- pF nS --- Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 3 of 10 Prepared byJaine Tsai PD42-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Power Dissipation vs. Ambient Temperature Fig.2 Spectral Sensitivity 200 1.0 Ta=25 C 0.8 0.6 150 100 0.4 50 0.2 0 100 300 500 700 900 1100 1300 0 -25 0 25 50 75 85 100 Fig.3 Dark Current vs. Ambient Temperature 1000 Fig.4 Reverse Light Current vs. Ee 7 5 100 3 10 VR=10V 1 20 40 60 80 100 1 VR=5V 0 0.05 0.5 1.0 2 3.0 Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 4 of 10 Prepared byJaine Tsai PD42-21C/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Reverse Voltage Fig.6 Response Time vs. Load Resistance 1 10 8 f=1MHZ VR=5V 10 2 VR=10V Ta=25C t 10 0 6 10 -1 4 10 10 -2 -3 2 0.1 1 10 100 10 1 10 2 10 3 10 4 10 5 Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 5 of 10 Prepared byJaine Tsai PD42-21C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 6 of 10 Prepared byJaine Tsai PD42-21C/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 7 of 10 Prepared byJaine Tsai PD42-21C/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% NO. Item Test Conditions Test Hours/ Sample Cycles Sizes 22pcs Failure Judgement Criteria ILLx0.8 Ac/Re 1 REFLOW Soldering TEMP.2605 6Mins 5secs 2 Temperature Cycle H : +100 15mins 50Cycles 5mins 15mins L : -40 3 Thermal Shock H :+100 L :-10 4 High Temperature Storage 5 Low Temperature Storage 5mins 50Cycles 10secs 5mins 1000hrs 1000hrs 1000hrs 1000hrs 0/1 0/1 LLower Specification Limit 22pcs 22pcs 0/1 TEMP.+100 TEMP.-40 22pcs 22pcs 22pcs 22pcs 0/1 0/1 0/1 0/1 6 DC Operating Life VR=5V 7 High Temperature/ 85 / 85% R.H High Humidity Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 8 of 10 Prepared byJaine Tsai PD42-21C/TR8 Package Dimensions Taping Dimensions Unit:mm Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 9 of 10 Prepared byJaine Tsai PD42-21C/TR8 Packing Quantity Specification 1.1000Pcs/1Volume1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHS PD42-21C/TR8 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT's consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. Device NoDTD-042-042 http:\\www.everlight.com Prepared date04-25-2006 Rev 2 Page: 10 of 10 Prepared byJaine Tsai |
Price & Availability of PD42-21C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |