View NCP2823AFCT2G_4728451.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP2823 Series High Efficiency 3W Filterless Class D Audio Amplifier
The NCP2823A/B are cost effective mono audio power amplifiers designed for portable electronic devices. NCP2823A is optimized for 8 W operation and NCP2823B can operate with speaker impedance down to 4.0 W. For Instance, NCP2823B is capable of delivering 3 W of continuous average power to a 4.0 W from a 5.0 V supply in a Bridge Tied Load (BTL) configuration. Under the same conditions, NCP2823A can provide 1.5 W to an 8.0 W BTL load with less than 10% THD+N. For cellular handsets or PDAs it offers space and cost savings because no output filter is required when using inductive transducers. With more than 90% efficiency and very low shutdown current, it increases the lifetime of your battery and drastically lowers the junction temperature. NCP2823 processes analog inputs with a pulse width modulation technique that lowers output noise and THD. The device allows independent gain while summing signals from various audio sources. Thus, in cellular handsets, the earpiece, the loudspeaker and even melody ringer can be driven with a single NCP2823. Due to its low 26 mV noise floor, A-weighted, clean listening is guaranteed no matter the load sensitivity.
Features http://onsemi.com MARKING DIAGRAM
9-PIN FLIP-CHIP CSP FC SUFFIX CASE 499AL XXX A Y WW G XXXG AYWW A1 = QTA for NCP2823A = PMA for NCP2823B = Assembly Location = Year = Work Week = Pb-Free Package
1
ORDERING INFORMATION
See detailed ordering and shipping information on page 10 of this data sheet.
* * * * * * * * * * *
Optimized PWM Output Stage: Filterless Capability Externally gain setting Low consumption: 1.8 mA for NCP2823A High efficiency: up to 92% Large Output Power Capability: 2 W @ VP = 5.0 V, 8.0 W High PSRR: up to -77 dB Fully Differential Capability: RF immunity Thermal and Auto recovery Short-Circuit Protection CMRR (-80 dB) Eliminates Two Input Coupling Capacitors Pin to Pin compatible with NCP2820 Flip-Chip These Devices are Pb-Free and are RoHS Compliant
1.45 mm 3.7 mm
Typical Applications

* Audio Amplifier for
Cellular Phones Digital Cameras Personal Digital Assistant and Portable Media Player GPS
(c) Semiconductor Components Industries, LLC, 2010
February, 2010 - Rev. P0
1
Publication Order Number: NCP2823/D
NCP2823 Series
A1 INP B1 AVDD C1 INN A2 A3
AGND VOUTN B2 PVDD C2 B3 PGND C3
EN VOUTP (Top View)
Figure 1. Pin Description
BATTERY Cs
VDD Ri INN Rf RAMP GENERATOR Negative Differential Input Rf Ri INP 300 kW EN Vih Vil
VOUTP
VOUTN
Positive Differential Input
Shutdown Control
GND
Figure 2. Simplified Block Diagram
http://onsemi.com
2
RL = 8 W
Data Processor
CMOS Output Stage
NCP2823 Series
PIN FUNCTION DESCRIPTION
Pin A1 C1 B2 B1 C3 A3 C2 B3 Pin Name INP INN PVDD AVDD VOUTP VOUTN EN PGND Type INPUT INPUT POWER POWER OUTPUT OUTPUT INPUT POWER Positive Differential Input Negative Differential Input Power Supply: This pin is the power supply of the device. A 4.7 mF ceramic capacitor or larger must bypass this input to the ground. This capacitor should be placed as close a possible to this input. Analog Power Supply: This pin must be connected to PVDD. Positive output Special care must be observed at layout level. See the Layout recommendations. Negative output: Special care must be observed at layout level. See the Layout recommendations. Enable: When a High logic is applied to this pin, the device is activated Power Ground: This pin is the power ground and carries the high switching current. A high quality ground must be provided to avoid any noise spikes/uncontrolled operation. Care must be observed to avoid high-density current flow in a limited PCB copper track. Analog Ground: This pin is the analog ground of the device and must be connected to GND plane. Description
A2
AGND
POWER
MAXIMUM RATINGS
Rating AVDD, PVDD Pins: Power Supply Voltage (Note 2) INP/N ,Pins: Input (Note 2) Digital Input/Output: EN Pin: Input Voltage Input Current Human Body Model (HBM) ESD Rating are (Note 3) Machine Model (MM) ESD Rating are (Note 3) WCSP 1.5 x 1.5 mm package (Notes 6 and 7) Thermal Resistance Junction-to-Case Operating Ambient Temperature Range Operating Junction Temperature Range Maximum Junction Temperature (Note 6) Storage Temperature Range Moisture Sensitivity (Note 5) Symbol VP VINP/N VDG IDG ESD HBM ESD MM RqJC TA TJ TJMAX TSTG MSL Value -0.3 to +6.0 -0.3 to +VDD -0.3 to VDD +0.3 1 2000 200 90 -40 to +85 -40 to +125 +150 -65 to +150 Level 1 Unit V V V mA V V C/W C C C C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Maximum electrical ratings are defined as those values beyond which damage to the device may occur at TA = 25C. 2. According to JEDEC standard JESD22-A108B. 3. This device series contains ESD protection and passes the following tests: Human Body Model (HBM) +/-2.0 kV per JEDEC standard: JESD22-A114 for all pins. Machine Model (MM) +/-200 V per JEDEC standard: JESD22-A115 for all pins. 4. Latch up Current Maximum Rating: $100 mA per JEDEC standard: JESD78 class II. 5. Moisture Sensitivity Level (MSL): 1 per IPC/JEDEC standard: J-STD-020A. 6. The thermal shutdown set to 150C (typical) avoids irreversible damage on the device due to power dissipation. 7. The RqCA is dependent on the PCB heat dissipation. The maximum power dissipation (PD) is dependent on the min input voltage, the max output current and external components selected.
R qCA +
125 * T A PD
* R qJC
http://onsemi.com
3
NCP2823 Series
ELECTRICAL CHARACTERISTICS Min and Max Limits apply for TA between -40C to +85C and for VDD between 2.5 V to 5.5 V
(Unless otherwise noted). Typical values are referenced to TA = + 25 C and VDD = 3.6 V. (see Note 8) Symbol Parameter Conditions Min Typ Max Unit
GENERAL PERFORMANCES VP FOSC IDD Operational Power Supply Oscillator Frequency Supply current NCP2823A VP = 3.6 V, No Load NCP2823B VP = 3.6 V, No Load VENL = VENR = 0 V EN rising edge EN falling edge VENL = 0 V 2.5 250 300 1.8 2.6 0.01 7.4 4 20 300 NCP2823A, VP = 3.6 V, Po = 600 mW, RL = 8 W, F = 1 kHz NCP2823B, VP = 3.6 V, Po = 1 W, RL = 4 W, F = 1 kHz Av FLP TSD TSDH VIH VIL RPLD voo PSRR Voltage gain -3 dB Cut off Frequency of the Built in Low Pass Filter Thermal Shut Down Protection Thermal Shut Down Hysteresis Rising Voltage Input Logic High Falling Voltage Input Logic Low Pull Down Resistor 1.2 285 kW Ri 92 90 300 kW Ri 30 150 10 - - 250 VDD 0.4 315 kW Ri V/V kHz C C V V kW 5.5 350 2.4 4.6 1 mA ms ms kW mW % V kHz mA
Isd TON TOFF Zsd RDS(ON) h
Shutdown current Turn ON Time Turn Off Time Class D Output impedance in shutdown mode Static drain-source on-state resistance of power Mosfets Efficiency
AUDIO PERFORMANCES Output offset Power supply rejection ratio F = 217 Hz, Input ac grounded F = 1 kHz, Input ac grounded SNR CMRR Vn Signal to noise ratio Common mode rejection ratio Output Voltage noise VP = 5 V, Pout = 600 mW (A. Weighted) Input shorted together VIC = 1 Vpp, f = 217 Hz Input ac grounded, Av = 0 dB No weighting A. Weighted 0.3 -77 -63 97 -80 35 26 dB dB mV mV dB
8. Performances guaranteed over the indicated operating temperature range by design and/or characterization, production tested at TJ = TA = 25C.
http://onsemi.com
4
NCP2823 Series
ELECTRICAL CHARACTERISTICS Min and Max Limits apply for TA between -40C to +85C and for VDD between 2.5 V to 5.5 V
(Unless otherwise noted). Typical values are referenced to TA = + 25 C and VDD = 3.6 V. (see Note 8) Symbol Parameter Conditions Min Typ Max Unit
AUDIO PERFORMANCES Po Output Power NCP2823A RL = 8 W F = 1 kHz THD+N < 1% VP = 5 V VP = 3.6 V VP = 2.5 V THD+N < 10% VP = 5 V VP = 3.6 V VP = 2.5 V NCP2823B RL = 4 W F = 1 kHz THD+N < 1% VP = 5 V VP = 3.6 V VP = 2.5 V THD+N < 10% VP = 5 V VP = 3.6 V VP = 2.5 V THD+N Total harmonic distortion plus noise VP = 3.6 V, Av = 6 dB, Po = 0.5 W VP = 5 V, Av = 6 dB, Po = 1 W 1.5 0.7 0.22 1.8 0.87 0.4 1.72 1.2 0.58 3 1.57 0.71 0.1 0.08 % W
8. Performances guaranteed over the indicated operating temperature range by design and/or characterization, production tested at TJ = TA = 25C.
http://onsemi.com
5
NCP2823 Series
TYPICAL OPERATING CHARACTERISTICS
100 90 80 70 60 (%) 50 40 30 20 10 0 0 500 1000 Pout (mW) 1500 2000 0.01 10 100 Pout (mW) 1000 10000 VP = 5.5 V 3.6 V 4.2 V 5V 3 V to 2.5 V THD (%) 10 2.7 V 1 3V 3.6 V 0.1 4.2 V 5V VP = 5.5 V 100 Pout @ 25C 2.5 V
Figure 3. Efficiency Vs Pout
100 2.5 V 0.1 5V 4.2 V 0.1 VP = 5.5 V 0.01 10 100 1000 10000 0.001 10 THD(%) 1
Figure 4. NCP2823A, THD+N vs Pout, RL = 8 W
VP = 2.7 V 10 THD (%) 2.7 V 3V 1 3.6 V
0.01
100
Pout (mW)
1000 FREQUENCY (Hz)
10000
100000
Figure 5. NCP2823B, THD+N vs Pout, RL = 4 W
1 1
Figure 6. THD+N vs Frequency Pout = 150 mW, RL = 8 W
0.1 THD(%) VP = 5 V 2.5 V 3.6 V THD(%)
0.1 VP = 3.6 V 0.01 VP = 5 V
0.01
0.001 10
100
1000 FREQUENCY (Hz)
10000
100000
0.001 10
100
1000 10000 FREQUENCY (Hz)
100000
Figure 7. THD+N vs Frequency Pout = 250 mW, RL = 8 W
Figure 8. THD+N vs Frequency Pout = 500 mW, RL = 8 W
http://onsemi.com
6
NCP2823 Series
TYPICAL OPERATING CHARACTERISTICS
1 VP = 5 V 1
VP = 2.7 V
0.1 THD(%) THD(%) 0.01
0.1
0.01
0.001 10
100
1000 10000 FREQUENCY (Hz)
100000
0.001
10
100
1000 10000 FREQUENCY (Hz)
100000
Figure 9. THD+N vs Frequency Pout = 1 W, RL = 8 W
1 1
Figure 10. THD+N vs Frequency Pout = 300 mW, RL = 4 W
0.1 THD(%) VP = 5 V 0.01 2.5 V 4.2 V THD(%)
0.1 VP = 3.6 V VP = 5 V 0.01
0.001 10
100
1000 10000 FREQUENCY (Hz)
100000
0.001
10
100
1000 10000 FREQUENCY (Hz)
100000
Figure 11. THD+N vs Frequency Pout = 500 mW, RL = 4 W
1 VP = 5 V 0 -10 -20 0.1 CMRR(dB) THD(%) -30 -40 -50 -60 -70 -80 0.001 10 100 1000 10000 FREQUENCY (Hz) 100000 -90 10
Figure 12. THD+N vs Frequency Pout = 1 W, RL = 4 W
0.01
VP = 2.5 V to 5.5 V
100
1000 10000 FREQUENCY (Hz)
100000
Figure 13. THD+N vs Frequency Pout = 2 W, RL = 4 W
Figure 14. CMRR vs Frequency, Vipp = 1 Vpp, RL = 8 W
http://onsemi.com
7
NCP2823 Series
TYPICAL OPERATING CHARACTERISTICS
0 -20 -40 CMRR (dB) PSRR (dB) -60 -80 Vrip = 200 mVpp -100 -120 10 Vrip = 1 Vpp 0 -10 -20 -30 -40 -50 -60 -70 -80 100 1000 10000 FREQUENCY (Hz) 100000 -90 10 VP = 4.2 V 100 1000 10000 FREQUENCY (Hz) 100000 3.6 V 2.5 V Input Grounded
Figure 15. CMRR vs Frequency vs VP
Figure 16. PSRR vs Frequency
0 -10 -20 PSRR (dB) -30 -40 -50 -60 -70 -80 -90 10 100 1000 FREQUENCY (Hz) 10000 100000 VP = 4.2 V 2.5 V 3.6 V Input Floating
Figure 17. PSRR vs Frequency
http://onsemi.com
8
NCP2823 Series
DETAIL OPERATING DESCRIPTION
General Description
The basic structure of the NCP2823A/B is composed of one analog pre-amplifier, a pulse width modulator and an H-bridge CMOS power stage. The first stage is externally configurable with gain-setting resistor Ri and the internal fixed feedback resistor Rf (the closed-loop gain is fixed by the ratios of these resistors). The load is driven differentially through two output stages. The differential PWM output signal is a digital image of the analog audio input signal. The human ear is a band pass filter regarding acoustic waveforms, which the typical cut off values are 20 Hz and 20 kHz. Thus, the user will hear only the amplified audio input signal within the frequency range. The switching frequency and its harmonics are fully filtered. The inductive parasitic element of the loudspeaker helps to guarantee a superior distortion value.
Power Amplifier
of this resistor is to eliminate any unwanted state changes when the Enable pin is floating.
30 kHz Built-in Low Pass Filter
This filter allows connecting directly a DAC or a CODEC to the NCP2823 input without increasing the output noise by mixing frequency with the DAC/CODEC output frequency. Consequently, optimized operation with DACs or CODECs is guaranteed without additional external components.
Power Supply Bypassing
The NCP2823 requires a correct decoupling of the power supply in order to guarantee the best operation in terms of audio performances. To achieve these performances, it is necessary to place a 4.7 mF low ESR ceramic capacitor as close as possible to the PVDD pin in order to reduce high frequency transient spikes due to parasitic inductance (see Layout considerations).
Input Capacitors Cin
The output PMOS and NMOS transistors of the amplifier have been designed to deliver a maximum output power before clipping. The channel resistance (Ron) of the NMOS and PMOS transistors is typically 0.3 W.
Gain Selection
The preamplifier stage amplifies the input signal. The gain is fully configurable by external resistors. The gain setting is given by the following equation:
Av + 300 kW Ri
(eq. 1)
Thanks to its fully differential architecture the NCP2823 does not require input capacitors. However, it is possible to use input capacitors when the differential source is not biased or in single ended configuration. In this case it is necessary to take into account the corner frequency which can influence the low frequency response of the NCP2823. The following equation will help choose the adequate input capacitor.
fC + 1 2 @ p @ Ri @ C in
(eq. 2)
Turn On and Turn Off Transitions
In order to reduce "pop and click" noises during transition, the output power in the load must not be established or cutoff suddenly. When logic high is applied to the Enable pin, the internal biasing voltage rises quickly and, 4 ms later, once the output DC level is around the common mode voltage, the gain is established slowly (5.0 ms). Thus, the total turn on time to get full power to the load is 7.4 ms (typical). The device has the same behavior when it is turned-off by a logic low on the Enable pin. No power is delivered to the load 4 ms after a falling edge on the shutdown pin. Due to the fast turn on and off times, the shutdown signal can be used as a mute signal as well.
Shutdown Function
Over Current Protection
This protection allows detecting an over current in the H-Bridge. When the current is higher than 2A for the NCP2823B or 1A for the NCP2823A, the H-Bridge is positioned in high impedance. When the short circuit is removed or the current is lower, the NCP2823 goes back to normal operation. This protection avoids over current due to a bad assembly (Output shorted together, to VDD or to ground).
Layout Recommendations
The device enters shutdown mode when the Enable signal is low. During the shutdown mode, the DC Shutdown current of the circuit does not exceed 1 mA. The NCP2823A/B has an internal resistor (RPLD = 250 kW) connected between GND and Enable. The purpose
For Efficiency and EMI standpoints, it is strongly recommended to use Power and ground plane in order to reduce parasitic resistance and inductance. For the same reason, it is recommended to keep the output traces short and well shielded in order to avoid them to act as antenna.
http://onsemi.com
9
NCP2823 Series
The EMI Level is strongly dependent upon the application. However, ferrite beads placed close to the NCP2823 will reduce EMI radiation when it is needed. Ferrite value is strongly dependent upon the application.
Figure 18. PCB Layout example ORDERING INFORMATION
Device NCP2823AFCT2G NCP2823BFCT2G Package WCSP - 9 - 1.45 x 1.45 mm (Pb-Free) WCSP - 9 - 1.45 x 1.45 mm (Pb-Free) Shipping 3000 / Tape & Reel 3000 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
Demo Board Available:
NCP2823AGEVB/D and NCP2823BGEVB/D evaluation board configure the device in typical application.
http://onsemi.com
10
NCP2823 Series
PACKAGE DIMENSIONS
9-PIN FLIP-CHIP CSP FC SUFFIX CASE 499AL-01 ISSUE O
-A- D -B- E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. COPLANARITY APPLIES TO SPHERICAL CROWNS OF SOLDER BALLS. MILLIMETERS MIN MAX 0.540 0.660 0.210 0.270 0.330 0.390 1.450 BSC 1.450 BSC 0.290 0.340 0.500 BSC 1.000 BSC 1.000 BSC
4X
0.10 C
TOP VIEW 0.10 C 0.05 C -C-
SEATING PLANE
A
DIM A A1 A2 D E b e D1 E1
A2 A1 SIDE VIEW D1 e
C B A
e
1 2 3
E1
9X
b
0.05 C A B 0.03 C BOTTOM VIEW
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
11
NCP2823/D

▲Up To Search▲

Price & Availability of NCP2823AFCT2G

	To Download NCP2823AFCT2G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .