View SMLP36RGB1W_4647576.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Tri-Color Top View 0604 <1.5 1.0 t=0.2mm> High Brightness Type
SMLP36 Series (under development)
Emitting Color Material Package Size(mm) Part No.
PICOLEDTM -RGB
Target Spec.
Green Red AlGalnP on GaAs
Blue InGaN on SiC
SMLP36RGB1W
1510(0604) 1.5x1.0(t=0.2)
Absolute Maximum Ratings (Ta=25C)
Power
Part No. Emitting dissipation color PD
Dimensions (Unit:mm)
1.5
(mW)
Blue Red
Peak Storage Forward Reverse Operating forward current voltage temperature temperature current Tstg Topr IF VR IFP (mA)1 (V) (C) (C) 2 (mA)
B
G
0.6 1.0 0.2 +0.05 -0.02 0.08
R
SMLP36
Green
64
20
100
5
-30 to +85
-40 to +100
1:The above absolute maximum ratings are valid for the case of lighting a single color. When lighting two colors at the same time, each of the figures in the absolute maximum ratings should be reduced down to 50% of it. When lighting three colors, it will be reduced down to 30% of it. (DC drive) 2:Conditions of IFP : Pulse width 1ms Duty 1/120
1.42 0.9 0.4 0.92 0.4
B
Anode
Electrical Optical Characteristics (Ta=25C)
Forward voltage VF
Typ. (V) 3.0 (3.2) SMLP36 IF (mA)
R
G
Part No.
Resin Color
Reverse current IR
Max. (A) VR (V)
Light wavelength
Dominant
D3 Typ. (nm) 470 IF (mA) Min.
Brightness IV
Typ. (mcd) 18 (50) 71 (200) 28 (100) 5 (20)
Green
X Y
Cathode
(mcd)
IF (mA)
Tolerance:0.1
9.0 (28) 5 36 (110) 14 (56)
Directivity (Typ.)
Angular Displacement (deg)
Milkey White
3.1 (3.3) 1.9 (2.2)
5 (20)
0 30 30
Red
100
5
527 624
Green Red
60
3:Measurement tolerance : 2nm
90 100
In preparation
50 0 50
60
90 100
RELATIVE LUMINOUS INTENSITY (%)
Red
X' Y'
Angular Displacement (deg)
0 30 30
Green, Red
Green
60
In preparation
50 0 50
60
90 100
90 100
RELATIVE LUMINOUS INTENSITY (%)
Recommended Pad Layout
0.45 0.45 0.4 0.4
Packaging Specifications (Unit:mm) Tape Specifications:1 <5,000pcs/reel>
Feeding direction 4.0 0.1 1.750.1
Reel Specifications
11.41
0.4
2.00.05
1.5 +0.1 0
0.200.08
13
0.45
3.50.05
8.00.2
The recommended thickness of the screen mask for soldering is between 80 and 130m. The hole size of the screen mask should be same as the recommended land pattern or smaller.
4.00.05
1.62
0.280.05
1.120.05
0.25
0.25
(Unit:mm)
3MAX
1.12
Tolerance:0.2
Tolerance:0.2
60 +1 0 0 180 -3
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright (c) 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121 FAX : +81-75-315-0172
Appendix1-Rev2.0

▲Up To Search▲

Price & Availability of SMLP36RGB1W

	To Download SMLP36RGB1W Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .