View HDF4553_4634618.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SPEC NO :
SPECIFICATION
CUSTOMER PRODUCT MODEL NO PREPARED APPROVED CHARLES
SAW FILTER HD F4553
CHECKED Houshihong D A T E
2007-7-14
CUSTOMER RECEIVED:
CHECKED
APPROVED
DATE
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 1 of 11
SAW FILTER
HD F4553
History Record
Date Spec No Part No Customer No Modify Content Remark
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 2 of 11
SAW FILTER
HD F4553
1.Features
_ RF bandpass filter for CDMA450 A-Band Tx. Part _ Usable bandwidth 5MHz (452.5 MHz ~ 457.5 MHz) _ High attenuation _ No matching single-ended operation _ Ceramic Surface Mounted Device Package ( 3.0 mm x 3.0mm ) _RoHS Compliant
2. ELECTRICAL SPECIFICATION
Parameter Operating Temperature Range Storage Temperature Range Power Handling Capability Electronic Characteristics 2-1.Typical frequency response Rating -30~85 -40~85 30 Unit C C dBm
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 3 of 11
SAW FILTER
HD F4553
2-2 Input / Output VSWR Charts
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 4 of 11
SAW FILTER
2-3.Electrical characteristics Minimum Center Frequency ( F0 ) Insertion Loss (F0 +/- 2.5 MHz) Amplitude Ripple (F0 +/- 2.5 MHz) VSWR (F0 +/- 2.5 MHz) Relative Attenuation 0.3 MHz ~ 350.0 MHz 350.0 MHz ~ 441.5 MHz 462.5 MHz ~ 467.5 MHz 467.5 MHz ~ 1200 MHz 1200 MH 2000 MH Input/Output Impedance MHz dB dB
-
HD F4553
Typical 455.0 2.0 0.8 1.4 30 30 50 30 50
Maximum
-
25 25 38 25 20 -
2.8 1.5 2.0 -
dB
-
3. TEST CIRCUIT
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 5 of 11
SAW FILTER
HD F4553
4-1. DIMENSION
4-2Marking Configuration
1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 6 of 11
SAW FILTER
HD F4553
Specifications
5.Environmental Performance Characteristics
Item High temperature Condition The specimen shall be store at a temperature of 852 for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of -303 for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of 402 with relative humidity of 90% to 96% for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be subjected to 8 continuous cycles each as shown below. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Temperature Duration 1 +25=>-40 0.5h 2 -40 4h 3 -40=>+85 2h 4 +85 4h 5 +85=>+25 0.5h 6 +25 1h Reflow soldering method Peak: 255 5 , 220 5, 40s At electrode temperature of the specimen.
Low temperature
Humidity
Thermal shock
Resistance to Soldering heat
Mechanical characteristics and specifications in electrical characteristics shall be satisfied. There shall be no excessive change in appearance.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 7 of 11
SAW FILTER
HD F4553
Solder ability
The specimen shall be passed through the reflow furnace with the condition shown in the above profile for 1 time. The specimen shall be stored at standard atmospheric conditions for 1h, after which the measurement shall be made. Test board shall be 1.6 mm thick. Base material shall be glass fabric base epoxy resin. Immerse the pins melt solder at 260+5/-0 More then 95% of for 5 sec. total area of the pins should be covered with solder
6.Mechanical Test
Items Vibration Drop Lead pull Lead bend Conditions 600-3300rpm amplitude 1.5mm 3 directions 2 H each On maple plate from 1m high 3 times Pull with 1kg force for 30 seconds 90o bending with 500g weigh 2 times Specifications There shall be no damage.
7. REMARK
7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 8 of 11
SAW FILTER
HD F4553
8. Packing
8.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 8.2 Reeling Quantity 1000 pcs/reel 7'' 3000 pcs/reel 13'' 8.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below.
(2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 9 of 11
SAW FILTER
HD F4553
9. TAPE SPECIFICATIONS
9.1 Tensile Strength of Carrier Tape: 4.4N/mm width 9.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15 (2) speed: 300mm/min. (3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W 12.00 0.30 F 5.50 0.10 E 1.75 0.10 P0 4.00 0.10 P1 4.00 0.10 P2 2.00 0.10 D0 O1.50 D1 O1.5 0.25 t1 0.31 0.05 t2 1.30 0.10 A 3.4 MAX. B 3.4 MAX
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 10 of 11
SAW FILTER
[Figure 2] [Unit:mm]
HD F4553
A O330 1.0
B O100 0.5
C O13 0.5
D O21 0.8
E 2 0.5
W 13 0.3
t 3 max.
r 1.0 max.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 11 of 11

▲Up To Search▲

Price & Availability of HDF4553

	To Download HDF4553 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .