 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SPEC NO : SPECIFICATION CUSTOMER PRODUCT MODEL NO PREPARED APPROVED CHARLES SAW FILTER HD F4552 CHECKED Houshihong D A T E 2007-01-25 CUSTOMER RECEIVED: CHECKED APPROVED DATE Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 1 of 13 SAW FILTER HD F4552 History Record Date Spec No Part No Customer No Modify Content Remark www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 2 of 13 SAW FILTER 1.Features _ RF bandpass filter for CDMA450 Tx. Part _ Usable bandwidth 5MHz (452.5MHz ~ 457.5 MHz) _ High attenuation _ No matching 50 single-ended operation _ Ceramic Surface Mounted Device Package ( 3.8 mm *3.8 mm ) HD F4552 2. Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range DC Voltage VDC Power Handling Capability Rating -30~85 -40~85 10 27 Unit C C V dBm 2-1-1Electrical characteristics( T=25C) Minimum Center Frequency ( F0 ) Insertion Loss (F0 +/- 2.5 MHz) Amplitude Ripple (F0 +/- 2.5 MHz) VSWR (F0 +/- 2.5 MHz) Relative Attenuation 0.3 MHz ~ 350.0 MHz 350.0 MHz ~ 441.0 MHz 462.5 MHz ~ 467.5 MHz 467.5 MHz ~ 1200 MHz Input/Output Impedance MHz dB dB - Typical 455.0 2.0 0.8 1.4 30 30 30 50 Maximum - 25 25 40 25 - 2.8 1.2 2.0 - dB - www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 3 of 13 SAW FILTER 2-1-2.Electrical characteristics( T=+70C~-20C) Minimum Center Frequency ( F0 ) Insertion Loss (F0 +/- 2.5 MHz) Amplitude Ripple (F0 +/- 2.5 MHz) VSWR (F0 +/- 2.5 MHz) Relative Attenuation 0.3 MHz ~ 350.0 MHz 350.0 MHz ~ 441.0 MHz 462.5 MHz ~ 467.5 MHz 467.5 MHz ~ 1200 MHz Input/Output Impedance MHz dB dB - HD F4552 Typical 455.0 2.0 0.8 1.4 30 30 30 50 Maximum - 25 25 30 25 - 3.5 1.2 2.0 - dB 2-2.Typical frequency response www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 4 of 13 SAW FILTER 2-3 Input / Output VSWR Charts HD F4552 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 5 of 13 SAW FILTER 2-4 Input / Output Smith Charts HD F4552 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 6 of 13 SAW FILTER HD F4552 3. TEST CIRCUIT 4-1. DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 7 of 13 SAW FILTER HD F4552 4-2Marking Configuration 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number 4) Lot Number 4-3 picture 5.Environmental Performance Characteristics Item High temperature Condition The specimen shall be store at a temperature of 852 for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of -303 for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Specifications Low temperature Humidity www.shoulder.cn Mechanical characteristics and specifications in electrical characteristics shall Page 8 of 13 SAW FILTER 402 with relative humidity of 90% to 96% for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be subjected to 8 continuous cycles each as shown below. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Temperature Duration 1 +25=>-40 0.5h 2 -40 4h 3 -40=>+85 2h 4 +85 4h 5 +85=>+25 0.5h 6 +25 1h Reflow soldering method Peak: 255 5 , 220 5, 40s At electrode temperature of the specimen. HD F4552 be satisfied. There shall be no excessive change in appearance. Thermal shock Resistance to Soldering heat Solder ability The specimen shall be passed through the reflow furnace with the condition shown in the above profile for 1 time. The specimen shall be stored at standard atmospheric conditions for 1h, after which the measurement shall be made. Test board shall be 1.6 mm thick. Base material shall be glass fabric base epoxy resin. Immerse the pins melt solder at 260+5/-0 More then 95% of for 5 sec. total area of the pins should be covered with solder Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn www.shoulder.cn Page 9 of 13 SAW FILTER HD F4552 6.Mechanical Test Items Vibration Drop Lead pull Lead bend Conditions 600-3300rpm amplitude 1.5mm 3 directions 2 H each On maple plate from 1m high 3 times Pull with 1kg force for 30 seconds 90o bending with 500g weigh 2 times Specifications There shall be no damage. 7. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 8. Packing 8.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 8.2 Reeling Quantity 1000 pcs/reel 7'' 3000 pcs/reel 13'' 8.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 10 of 13 SAW FILTER HD F4552 (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 11 of 13 SAW FILTER HD F4552 9. TAPE SPECIFICATIONS 9.1 Tensile Strength of Carrier Tape: 4.4N/mm width 9.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15 (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W 12.00 0.30 F 5.50 0.10 E 1.75 0.10 P0 4.00 0.10 P1 8.00 0.10 P2 2.00 0.10 D0 O1.50 D1 O1.0 0.25 t1 0.25 0.05 t2 1.65 0.10 A 4.04 0.10 B 4.10 0.10 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 12 of 13 SAW FILTER [Figure 2] [Unit:mm] HD F4552 A O330 1.0 B O100 0.5 C O13 0.5 D O21 0.8 E 2 0.5 W 13 0.3 t 3 max. r 1.0 max. 10.REVIRION Date 2005-6-15 2006-5-16 2006-5-25 2006-7-7 2008-1-30 Page Revision A B C D E Reason NEW Customer's require Customer's require Customer's require Customer's require www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 13 of 13 |
Price & Availability of HDF4552
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |