 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 450-550 Watts 12V DS450-3/DS550-3 Distributed Power System 850 Watts 12V DPS Input Distributed Power Bulk Front-End Total Output Power: 450W - 550W +12vdc Main Output +3.3vdc Stand-By Output Wide Range Input Voltage: 90 - 264VAC Electrical Specs Input Range Frequency Inrush Current Efficiency Conducted EMI Radiated EMI Power Factor Leakage Current Hold Up Time 90 - 264vac 47 - 63 Hz, single phase AC 15A Maximum 84% typical at full load, high line FCC Subpart J EN55022 Class A FCC Subpart J EN55022 Class A 0.99 typical 1.30mA @ 240VAC 20ms Minimum Special Features * * * * * * * * * * * * * * * * * * * * Active Power Factor Correction EN61000-3-2 Harmonic Compliance Active AC Inrush Control 1U X 2U Form Factor 10.3W / in3 (DS550) 8.4W / in3 (DS450) +12vdc Output +3.3vdc Stand-By No Minimum Load Required Hot Plug Operation N + 1 Redundant Internal OR'ing Fets Active Current Sharing Built-in Cooling Fans (40mm x 28mm) I2C Communication Interface Bus EERPOM for FRU Data Amber LED Status, Fan_Fail Green LED Status, Power Good / AC_OK Status Internal Fan Speed Control Fan Fail Tach Output Signal One Year Warranty Output Main DC Voltage Stand-By Adjustment Range Regulation Over Current Over Voltage Under Voltage Turn-On Delay +12vOutput Rise Time +12v +3.3vsb Factory Set, no pot adjustments +12vdc; +5%/-3% +3.3vsb; +5%/-4% See Table 1 next page +12vdc; 13.5 - 15vdc +3.3vsb; 3.76 - 4.30vdc +12vdc; 11.0 - 11.5vdc +3.3vsb; 2.77 - 3.00vdc 1 Second max, 2 - 20mS, Monotonic Logic Control PS Inhibit When supply is inserted into the system the pin is pulled LOW and power supply is ON after all other pins are seated I2C port P6. When the power supply is on and running normal P6 is low. When the power supply is off, either due to -PS_ON, PS_KILL, or a fault, then P6 is high. I2C port P7. P7 is high except when the power supply turns the main outputs, not +3.3VSB, off due to an AC failure (AC missing or too low for power supply operation). If the supply is turned off due to -PS_ON, PS_KILL, or a fault, then P7 remains high. The PSU will provides an open collector Tach 1 output. This signal is generated from the fan. The signal should generate 2 pulses per revolution. The logic in the system will be operating at 3.3V. PS_Status Environmental Operating Temperature: -10C to 50C (50% power derating at 70C) Storage Temperature: -40 to +70C Altitude, Operating 10,000ft Electromagnetic Susceptibility / Input Transients: -EN61000-3-2, -3-3 -EN61000-4-2, 4-4, -4-5, 4-11 Level -EN55024:1998 Humidity: 20 to 90% RH, non-condensing Shock and Vibration Specification (Complies with Astec Std Specification, Q3205 MTBF (Demonstrated): 400KHrs at full load, 40C AC_Pfail Fan_Fault Tach_1 Safety UL/cUL 60950 (UL Recognized) NEMKO+ CB Report EN60950 EN60950 CE Mark China CCC Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 Rev 6.20.07 AMERICAS 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 EUROPE Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 ASIA Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Ordering Information Table 1 Output Nominal Output Voltage Set Point 12.0vdc 3.30vsb 12.0vdc 3.30vsb Set Point Tolerance +/-0.2% +/-1% +/-0.2% +/-1% Total Regulation +5/-3% +5/-4% +5/-3% +5/-4% Minimum Current 0A 0A 0A 0A Maximum Current 37.0A 3.0A 45.0A 3.0A Output Ripply P/P 120mV 60mV 120mV 60mV Over Current 39.5 - 44.4A 4.9A Avg, 7A Max 48.0A - 54.0A 4.9A Avg, 7A Max DS450-3 DS550-3 Table 2 DC Output Connector Pinout Assignment P1 - Power Supply Side 1. FCI Power Blade 51721 series 51721-10002406AA 2. Molex Power Connector SD-87667 series 87667-7002 Mating Connector (System Side) 1.FCI Power Blade 51741-10002406CC Strait Pins 2.FCI Power Blade 51761-10002406AA Right Angle Pin PB 1 PB 2 PB 3 PB 4 PB 5 PB 6 A1 A2 A3 A4 A5 A6 B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 D1 D2 D3 D4 D5 D6 Male connector as viewed from the rear of the supply: D1 D2 D3 D4 D5 D6 Signal Name C1 C2 C3 C4 C5 C6 PB1 PB2 PB3 PB4 PB5 PB6 +12V RETURN B1 B2 B3 B4 B5 B6 +12V RETURN A1 A2 A3 A4 A5 A6 +12V RETURN +12V +12V +12V PS_KILL +12V CURRENT SHARE LOGIC RETURN +3V3 STAND-BY A0 (I2C Address BIT 0 Signal) +3V3 STAND-BY LOGIC RETURN SPARE LOGIC RETURN +3V3 STAND-BY SDA (I2C Data Signal) PSON (Power Enable Signal) LOGIC RETURN TACH 1 (Fan Fail Signal) LOGIC RETURN +3V3 STAND-BY SCL (I2C Clock Signal) VIN_GOOD (AC Input Present) -PS_PRESENT ( Power Supply Seated) SPARE LOGIC RETURN +3V3 STAND-BY S_INT (Alert) POK (Output Power Ok) www.astecpower.com 2 3 (2X) 10.02" (254.7) F 1.52" (38.4) 1.453" (36.9) J G 13.29" (337.6) 12.03"0.3" (305.6 0.8) 10.88" (276.4) (3X) 10.02" (254.7) F E Mechanical Dimensions 1.575" 0.3" (40.0 0.8) 1.51" .03" (38.4 0.8) NOTE: Dimensions given in (mm). D 3.07" (78.0) K 11.925" 0.3" (302.9 0.8) 10.02" (254.6) F A 'POWER GOOD' GREEN B .3976" .028" (10.1 0.5) 'FAULT' YELLOW 'AC GOOD' GREEN .972" 0.2" 24.7 0.5 H 41.5 LATCH SPRING DISTANCE (REF.) C .138" .020" (3.5 0.5) (3X) 254.6 F 3.0 0.3 2.84" (72.2) .228 .02 (5.8 0.5) .197" .02" (5.0 0.5) .1496" .02" (3.8 0.5) 2.913" .024") (74.0 0.6) Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 STD AIRFLOW 3.071" .03" (78.0 0.8) |
Price & Availability of DS450-3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |