View MT6224-OG-A_4533147.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3Northway Lane North Latham,New York 12110.
Tollfree:1.800.984.5337 Phone:1.518.956.2980 Fax:1.518.785.4725 Http://www.marktechopto.com
SPECIFICATION
PART NO. : MT6224-OG-A 5.0mm ROUND BI- POLAR LAMP (3LEADS)
ATTENTION
OBSERVE PRECAUTION FOR HANDLING ELECTRO STATIC SENSITIVE DEVICES
MT6224-OG-A
Description
5.0mm ROUND BI- POLAR LAMP (3LEADS)
This green and amber bi-color lamp is made with GaP/GaP green chip, GaAsP/GaP amber chip and white diffused epoxy resin.
GREEN ANODE
COMMON CATHODE
AMBER ANODE
Notes: 1. All dimensions are in mm. 2. Tolerance is 0.25mm unless otherwise noted.
Description
LED Chip Part No.
Material GaP/GaP MT6224-OG-A GaAsP/GaP Amber Emitting Color Green White diffused
Lens Color
VER.: 01
Date: 2007/11/11
Page: 1/5
MT6224-OG-A
Absolute Maximum Ratings at Ta=25
Parameter
Power Dissipation Reverse Voltage D.C. Forward Current Reverse (Leakage) Current Peak Current(1/10Duty Cycle,0.1ms Pulse Width.) Operating Temperature Range Storage Temperature Range Soldering Temperature(1.6mm from body)
5.0mm ROUND BI- POLAR LAMP (3LEADS)
Symbol
PD VR If Ir If(Peak) Topr. Tstg. Tsol.
Rating
78 5 30 100 100 -40 to +95 -40 to +100 Dip Soldering : 260 Hand Soldering : 350
Unit
mW V mA A mA
for 5 sec. for 3 sec.
Electrical and Optical Characteristics:
Parameter
Luminous Intensity Forward Voltage Peak Wavelength Dominant Wavelength Reverse (Leakage) Current Viewing Angle Spectrum Line Halfwidth 2
Green
Min.
9.8
Symbol
IV Vf p d Ir 1/2
Condition
If=20mA If=20mA If=20mA If=20mA Vr=5V If=20mA If=20mA
Typ.
20.0 2.1 567 572
Max.
Unit
mcd
2.6
V nm nm
100 70 30
A deg nm
Notes:
The datas tested by IS tester. 2. Customer's special requirements are also welcome.
VER.: 01
Date: 2007/11/11
Page: 2/5
MT6224-OG-A
Absolute Maximum Ratings at Ta=25
Parameter
Power Dissipation Reverse Voltage D.C. Forward Current Reverse (Leakage) Current Peak Current(1/10Duty Cycle,0.1ms Pulse Width.) Operating Temperature Range Storage Temperature Range Soldering Temperature(1.6mm from body)
5.0mm ROUND BI- POLAR LAMP (3LEADS)
Symbol
PD VR If Ir If(Peak) Topr. Tstg. Tsol.
Rating
78 5 30 100 100 -40 to +95 -40 to +100 Dip Soldering : 260 Hand Soldering : 350
Unit
mW V mA A mA
for 5 sec. for 3 sec.
Electrical and Optical Characteristics:
Parameter
Luminous Intensity Forward Voltage Peak Wavelength Dominant Wavelength Reverse (Leakage) Current Viewing Angle Spectrum Line Halfwidth 2
Amber
Min.
9.8
Symbol
IV Vf p d Ir 1/2
Condition
If=20mA If=20mA If=20mA If=20mA Vr=5V If=20mA If=20mA
Typ.
20.0 2.1 610 605
Max.
Unit
mcd
2.6
V nm nm
100 70 35
A deg nm
Notes:
The datas tested by IS tester. 2. Customer's special requirements are also welcome.
VER.: 01
Date: 2007/11/11
Page: 3/5
MT6224-OG-A
5.0mm ROUND BI- POLAR LAMP (3LEADS)
Typical Electrical / Optical Characteristics Curves :
50 40 30 20 10
25.0 Relative Luminous Intensity 20.0 15.0 10.0 5.0 0
Forward Current IF(mA)
1.2
1.6
2.0
2.4
2.8
3.2
0.0
10.0
20.0
30.0
Forward Voltage (V) FORWARD CURRENT VS.APPLIED VOLTAGE
Forward Current (mA)
FORWARD CURRENT VS. LUMINOUS INTENSITY
0
50 40
10
20 30
Forward Current IF(mA)
40
30 20 10
1.0 0.9 0.8
50 60 70 80 90 0.5 0.3 0.1 0.2 0.4 0.6
0.7
0 20 40 60 Temperature( C) 80 100
FORWARD CURRENT VS. AMBIENT TEMPERATURE
RADIATION DIAGRAM
VER.: 01
Date: 2007/11/11
Page: 4/5
MT6224-OG-A
Precautions:
TAKE NOTE OF THE FOLLOWING IN USE OF LED 1. Temperature in use
5.0mm ROUND BI- POLAR LAMP (3LEADS)
Since the light generated inside the LED needs to be emitted to outside efficiently, a resin with high light transparency is used; therefore, additives to improve the heat resistance or moisture resistance (silica gel , etc) which are used for semiconductor products such as transistors cannot be added to the resin. Consequently, the heat resistant ability of the resin used for LED is usually low; therefore, please be careful on the following during use. Avoid applying external force, stress, and excessive vibration to the resins and terminals at high temperature. The glass transition temperature of epoxy resin used for the LED is approximately 120-130 . At a temperature exceeding this limit, the coefficient of liner expansion of the resin doubles or more compared to that at normal temperature and the resin is softened. If external force or stress is applied at that time, it may cause a wire rupture. 2. Soldering Please be careful on the following at soldering. After soldering, avoided applying external force, stress, and excessive vibration until the products go to cooling process (normal temperature), (1) (2) (3) Soldering measurements: Distance between melted solder side to bottom of resin shall be 1.6mm or longer. Solder dip: Preheat: 90 Solder bath: 260 5 Soldering iron : 350 max. (Backside of PCB), Within 60 seconds (Solder temperature), Within 5 seconds max. (Temperature of soldering iron tip), Within 3 seconds
3. Insertion Pitch of the LED leads and pitch of mounting holes need to be same 4. Others Since the heat resistant ability of the LED resin is low, SMD components are used on the same PCB, please mount the LED after adhesive baking process for SMD components. In case adhesive baking is done after LED lamp insertion due to a production process reason, make sure not to apply external force, stress, and excessive vibration to the LED and follow the conditions below. Baking temperature: 120 max. Baking time: Within 60 seconds If soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down the LED to normal temperature.
VER.: 01
Date: 2007/11/11
Page: 5/5

▲Up To Search▲

Price & Availability of MT6224-OG-A

	To Download MT6224-OG-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .