View HMC783LP6CE10_4536684.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Features
* RF Bandwidth: 11.5 GHz to 12.5 GHz * Fractional or Integer Modes * Ultra Low Phase Noise 12 GHz; 50 MHz Ref. -95 / -99 dBc/Hz @ 10 kHz (Frac / Int) -134 dBc/Hz @ 1 MHz (Open Loop) * Figure of Merit (FOM) -221 / -226 dBc/Hz (Frac / Int) * 24-bit Step Size, Resolution 3 Hz typ * 225 MHz, 14-bit reference path input * Direct FSK Modulation Mode * Cycle Slip Prevention * Read / Write Serial Port, Chip ID * 40 Lead 6x6mm SMT Package: 36mm2
Typical Applications
6
PLLS w/ INTEGRATED VCO - SMT
* VSAT Radio * Point-to-Point / Multi-Point Radio * Test Equipment & Industrial Control
* Military End-Use * Phased Array Applications
Functional Diagram
[1] Please refer to the pin description table for details
6 - 30
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
General Description
The HMC783LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The input reference frequency range is 100 kHz to 220 MHz while the advanced delta-sigma modulator design in the fractional synthesizer allows both ultra-fine step sizes and very low spurious products. The highly integrated structure provides excellent phase noise performance over temperature, shock and process. The HMC783LP6CE is packaged in a leadless QFN 6x6 mm surface mount package. The output power is 11 dBm typical, making the HMC783LP6CE ideal for driving the LO port of many of Hittite's Hi Linearity and I/Q mixer products. For theory of operation and register map refer to the "PLLs w/ Integrated VCO - Microwave VCOs" Operating Guide. To view the Operating Guide, please visit www.hittite.com and choose HMC783LP6CE from the "Search by Part Number" pull down menu.
Electrical Specifi cations, TA = +25 C; VCCVCO, VDDCP, VCCCP = +5V; AVCC, VCCPS
VDDPFD, AVDD, RVDD, DVDD, DVDDM, DVDDQ, VDDIO = +3.3V; AGND = DGND = 0V
Parameter Condition Min. Typ. Max. Units
6
V
RF Output Characteristics
VCO Output Frequency Range VCO Output Power VCO Tuning Voltage VCO Tuning Sensitivity Frequency Pulling (into a 2:1 VSWR) Frequency Pushing Frequency Drift Rate Sub Harmonic (1/2) Harmonic (2nd) Harmonic (3rd) VCO SSB Phase Noise @ 100 kHz Offset (Open Loop) Synthesizer In-Band SSB Phase Noise @ 10 kHz Offset (Frac/Int) Synthesizer Normalized In-Band SSB Phase Noise Floor (Frac/Int) Synthesizer Fractional Spurs [1] Synthesizer Frequency Settling Time (100 MHz Step) 16-Bit Divider Range (Int) 16-Bit Divider Range (Frac) From 12.1 GHz to 12 GHz Loop BW = 100 kHz N Divider Ratio 216+31 N Divider Ratio 216 -1 32 36 V TUNE = +5V Fvco = 12 GHz Fref = 50 MHz Fvco = 12 GHz Loop BW = 100 kHz V TUNE = +5V V TUNE = +5V 11.5 5 2 160 8 6 1.2 30 24 40 -110 -95 / -99 -221 / -226 -65 104 65567 65535 12 12.5 15 13 GHz dBm
MHz/V MHz pp MHz/V MHz/ C dBc dBc dBc dBc/Hz dBc/Hz dBc/Hz dBc us
REF Input Characteristics
Max Ref Input Frequency (3.3V) Min Ref Input Frequency Ref Input Sensitivity Max Ref Input Ref Input Capacitance 14-Bit Ref Divider Range 16383 AC Coupled DC Coupled 0 200 225 100 500 200 700 VDDIO 5 1 MHz kHz mVpp V pF
[1] Actual spur level is dependent on loop parameters and will increase at division ratios closest to integer boundaries. Number listed is average value.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
6 - 31
PLLS w/ INTEGRATED VCO - SMT
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Electrical Specifi cations (Continued)
Parameter Condition Min. Typ. Max. Units
Phase Detector
Max Phase Detector Frequency (Frac) Max Phase Detector Frequency (Int) Min Phase Detector Frequency 70 140 105 160 100 MHz MHz kHz
Charge Pump
Max Output Current Min Output Current Charge Pump Noise Input referred 50 MHz Ref. 2 500 -145 mA A dBc/Hz
Logic Inputs
6
PLLS w/ INTEGRATED VCO - SMT
VIH Input High Voltage VIL Input Low Voltage
VDDIO-0.4 0
VDDIO 0.4
V V
Logic Outputs
VOH Output High Voltage VOL Output Low Voltage Serial Port Max Clock VDDIO-0.4 0 50 VDDIO 0.4 V V MHz
Power Supply Voltages
Analog 3.3V Supplies: AVCC, VDDPFD, AVDD, RVDD, VCCPS Digital Internal Supplies: DVDD, DVDDQ, DVDDM Digital I/O Supplies: VDDIO Analog 5V Supplies: VCCVCO, VDDCP, VCCCP Logic I/O VCCCP must equal VDDCP AVDD must equal DVDD 3 3 1.8 4.75 3.3 3.3 3.3 5 3.45 3.45 5.5 5.25 V V V V
Power Supply Currents
Total Current Consumption (5V) Total Current Consumption (3.3V) Power Down Current [1] CSP Disabled CSP Enabled Measured with 10 G meter 1.880 145 90 1 450 1.920 1.960 190 110 10 mA mA A A V
Bias Reference Voltage
[1] Refers only to the Synthesizer portion of the HMC783LP6CE
6 - 32
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
SSB Phase Noise vs. Frequency, Integer Mode
-60 -70 11.5 GHz 12.0 GHz 12.5 GHz
SSB Phase Noise vs. Temperature @ 12 GHz, Integer Mode
-60 -70 +25 C +85 C -40 C
PHASE NOISE (dBc/Hz)
-80 -90 -100 -110 -120 -130 -140 -150 10
2
PHASE NOISE (dBc/Hz)
-80 -90 -100 -110 -120 -130 -140 -150 2 10 Fref = 50 MHz Loop BW = 100 kHz
3 4 5 6
Temp = 25C Fref = 50 MHz Loop BW = 100 kHz
3 4 5 6 7
10
10
10
10
10
10
10
10
10
10
7
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
6
PLLS w/ INTEGRATED VCO - SMT
6 - 33
SSB Phase Noise Fractional Spurs @ 12.002 GHz
-60 -70
SSB Phase Noise vs. Reference Freq. & Loop BW @ 12 GHz, Integer Mode
-60 -70
PHASE NOISE (dBc/Hz)
PHASE NOISE (dBc/Hz)
-80 -90 -100 -110 -120 -130 -140 -150 2 10 Temp = 25C Fref = 50 MHz Loop BW = 100 kHz 10
3
-80 -90 -100 -110 -120 -130 -140 Fref = 10MHz Loop BW= 10kHz Fref = 50MHz Loop BW=100kHz
10
4
10
5
10
6
10
7
-150 2 10
10
3
10
4
10
5
10
6
10
7
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
Example of Cycle Slip Prevention Hop from 12.2 to 11.7 GHz
12.3 12.2
Typical Reference Sensitivity vs. Frequency, 3.3V [1]
20 10 R = Max, +25C R = Max, +85C
FREQUENCY (GHz)
12.1 12 11.9 11.8 11.7 11.6 -20 -10 0 10 20 30 40 50 60 70 80 CSP ON CSP OFF
SENSITIVITY (dBm)
0 -10 -20 -30 -40 -50 R = 3, +25C R = 3, +85C
0
50
100
150
200
250
300
TIME (SEC)
FREQUENCY (MHz)
[1] R refers to the reference path division ratio
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Frequency vs. Tuning Voltage, T= 25C
13.4
Frequency vs. Tuning Voltage, Vcc= +5V
13.4
OUTPUT FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
13.1 12.8 12.5 12.2 11.9 11.6 11.3 11 10.7 10.4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 Vcc=4.75V Vcc=5.00V Vcc=5.25V
13.1 12.8 12.5 12.2 11.9 11.6 11.3 11 10.7 10.4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 +25C +85C -40C
6
PLLS w/ INTEGRATED VCO - SMT
700 600 500 400 300 200 100 0 0 1 2 3
TUNING VOLTAGE (V)
TUNING VOLTAGE (V)
Sensitivity vs. Tuning Voltage, Vcc= +5V
Output Power vs. Tuning Voltage, Vcc= +5V
14 13
OUTPUT POWER (dBm)
SENSITIVITY (MHz/V)
12 11 10 9 8 7 6 5 4 +25C +85C -40C
+25C +85C -40C
4
5
6
7
8
9
10
11
12
13
0
1
2
3
4
5
6
7
8
9
10
11
12
13
TUNING VOLTAGE (V)
TUNING VOLTAGE (V)
Open Loop VCO SSB Phase Noise @ Vtune = +5V
0
Open Loop VCO SSB Phase Noise vs. Tuning Voltage
0
SSB PHASE NOISE (dBc/Hz)
-40 -60 -80 -100 -120 -140 -160 10
3
+25C +85C -40C
SSB PHASE NOISE (dBc/Hz)
-20
-20 -40 -60 -80 -100 -120 -140 10KHz Offset 100KHz Offset
10
4
10
5
10
6
10
7
1
2
3
4
5
6
7
8
9
10
11
12
13
OFFSET FREQUENCY (GHz)
TUNING VOLTAGE (V)
6 - 34
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Pin Descriptions
Pin Number 1, 9 - 13, 22, 36 2 - 4, 7, 37, 39 5 8 40 6 14 Function N/C GND [1] GND VCCVCO2 [2] +5V Power Supply for VCO VCCVCO1 VTUNE ACG Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. AC Ground. This pin must be connected to an external capacitor to ground. Analog Power supply pin for the RF Section. A decoupling capacitor to the ground plane should be placed as close as possible to this pin. Nominally 3.3V +5V Power Supply for charge pump digital section +5V Power Supply for the charge pump analog section Charge pump output Analog Power supply for the phase frequency detector, Nominally 3.3V External bypass decoupling for precision bias circuits, 1.920V 20 mV is generated internally Analog Power supply for analog ref paths, Nominally 3.3V Reference input (Negative or AC coupled to GND) Reference input (Positive) Ref path supply Digital supply for Substrate, Nominally 3.3V Chip Enable Serial port latch enable input Serial port clock input Serial port data input Power supply pin for internal digital circuitry. Nominally 3.3V Power Supply for digital I/O driver Lock Detect, Main Serial Data Output or VCO Serial Port Data Out Analog Power Supply for Prescaler, Nominally 3.3V Digital Power Supply for M-Counter, Nominally 3.3V RF output (AC coupled). Description No Connection. These pins may be connected to RF/DC ground. Performance will not be affected. These pins must be connected to RF/DC Ground These pins and package bottom must be connected to RF/DC Ground
15 16 17 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 35 38
AVCC VDDCP VCCCP CP VDDPFD BIAS [3] AVDD REFN REFP RVDD DVDDQ CE SEN SCK SDI DVDD VDDIO LD_SDO VCCPS DVDDM RFOUT
6
PLLS w/ INTEGRATED VCO - SMT
6 - 35
[1] This pin is not connected internally, however, this pin must be connected to GND to maintain product family pin for pin compatibility. [2] This pin is not connected internally, however, this pin must be connected to Vcc to maintain product family pin for pin compatibility. [3] BIAS ref voltage (pin 20) cannot drive an external load, and must be measured with a 10 GOhm meter such as Agilent 34410A; a typical 10 Mohm DVM will read erroneously.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Pin Schematic Equivalents
Pins Equivalent Schematic
RFOUT
VCCVCO1
6
VTUNE
PLLS w/ INTEGRATED VCO - SMT
GND
SEN, CE, SCK, SDI
LD_SDO
CP
6 - 36
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Pin Schematic Equivalents (Continued)
Pins Equivalent Schematic
Bias
6
PLLS w/ INTEGRATED VCO - SMT
6 - 37
REFN, REFP
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Evaluation Circuit
3VDIGITAL
R8 100K
2
3VANALOG
C12 100NF C10 10PF C8 10PF C9 100NF
3VDIGITAL
CEN 3VDIGITAL
C14 100NF
1
C13 10PF
A B C D
JP1 R20 1K J3
1
RFout
C15 100PF
50 Ohm Co-Planar Trace
5VVCO
6
PLLS w/ INTEGRATED VCO - SMT
TP6
SDO
5016 TP5
SYNTH
C32 4.7UF C38 1NF
2
5016
NC NC NC ACG AVCC VDDCP VCCCP CP VDDPFD BIAS
GND
1 2 3 4 5 6 7 8 9 10
VCCVCO1 GND RFOUT GND NC DVDDM VCCPS LD_SDO VDDIO DVDD
JP2
LD
2
C4 4.7UF
C1 1NF
40 39 38 37 36 35 34 33 32 31
NC GND GND GND GND VTUNE GND VCCVCO2 NC NC
U1 HMC783LP6CE
SDI SCK SEN CE DVDDQ RVDD REFP REFN NC AVDD
30 29 28 27 26 25 24 23 22 21
1
E F G H
C21 1NF
11 12 13 14 15 16 17 18 19 20
JP3
C35 100NF
C31
1
100PF
R23 C65
DEPOP
R27 DEPOP
0 L1
R28
DEPOP
C61 3.9NF
DEPOP R21 30 R3 1K R12
DEPOP
I
R13 182 C37 3.9NF C33 1.5NF
C62
DEPOP
R4 620 C64
DEPOP
J
+15V
TP4 FB4 C57 22UF 1000 FB3 1000 THS4031IDGN
4
C63
DEPOP
K
C58 4.7UF C39 1NF
6 7 2
5016 TP3
R25
DEPOP
U5
3
R26
DEPOP
R22 R15 10K C60 1NF R14 10K
0
L
5016
GND
JP6
1 2
M
6 - 38
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Evaluation Circuit (Continued)
Header to USB Board
J1
A B C D
R1 100K
SCK SDI SDO SEN CEN
1 3 5 7 9 11
2 4 6 8 10 12 NC NC NC NC
3VDIGITAL
TLW-106-05-T-D
3VDIGITAL
C5 10PF C7 100NF
3VANALOG
C2 10PF C3 100NF
6
5V
J2 R9
1
C34 100NF R6 R2 120 56 R7 120 C40
3
100NF
TCXO
FOUT
Y2
GND 2
VDD VC
4 1
3VTCXO
100NF
C6 10PF
C28 100NF R24
10
DEPOP
C30 DEPOP
R10 0
5VCP
I
C16 10PF C18 100NF
3VANALOG
3VAN
J
C22 10PF C23 100NF
3VANALOG
K
C24 10PF C25 100NF
5VCP
3VDIG
L
C26 10PF C27 100NF
3VANALOG
3VTC
M
5VCP
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
6 - 39
PLLS w/ INTEGRATED VCO - SMT
E F G H
50 Ohm Trace
C29
REFin
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Evaluation Circuit (Continued)
5.5V GND
R41 1K
2
TP2
FB2 1000 C42 100NF C59 4.7UF FB1 1000
5016 TP1
5016
JP5
1
U9 LP3878MR-ADJ
SD 8 4 1 3 6 ADJ VIN BPASS VOUT GND
R11 4.02K
R40 4.02K
C67 1.2NF
C41 100NF C73 10NF
C74 4.7UF
5
6
PLLS w/ INTEGRATED VCO - SMT
CXO
5VVCO
C36 100NF C68 4.7UF
R17 1K
6
U8 LP3878MR-ADJ
SD 8 4 1 3 ADJ VIN BPASS VOUT GND
R16 4.02K
C44 1.2NF
C43 100NF C47 10NF
C48 4.7UF
5
5VCP
C46 100NF C45 4.7UF
U2 LP5900-3_3V
3VANALOG
C19 10PF C20 100NF
1
VOUT
VIN
6 4
GND EN 3
R5 10K
C11 100NF
C17 4.7UF
3VDIGITAL
C51 10PF C52 100NF
U4 LP5900-3_3V
1 VOUT VIN
6 4
GND EN 3
R18 10K
C50 100NF
C49 4.7UF
3VTCXO
C55 10PF C56 100NF
U6 LP5900-3_3V
1 VOUT VIN
6 4
GND EN 3
R19 10K
1
C54 100NF JP4
2
C53 4.7UF
6 - 40
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Absolute Maximum Ratings
Nominal 3.3V Supplies to GND Nominal Digital Supply Relative to 3.3V Analog Supply Nominal 5V Supply to GND Vtune Storage Temperature Max Peak Reflow Temperature ESD Sensitivity (HBM) -0.3V to +3.6V -0.3V to +0.3V -0.3 to +5.5V 0 to +15V -65 to +150C 260 C Class 1A
Reliability Information
Junction Temperature to Maintain 1 Million Hour MTTF Nominal Junction Temperature (T=85 C) Thermal Resistance (Junction to GND Paddle, 5V Supply) Operating Temperature 135 C 120 C 48.3 C/W -40 to +85C
6
PLLS w/ INTEGRATED VCO - SMT
H783 XXXX
Outline Drawing
NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number HMC783LP6CE Package Body Material RoHS-compliant Low Stress Injection Molded Plastic Lead Finish 100% matte Sn MSL Rating MSL3 Package Marking [1]
[1] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
6 - 41
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
Evaluation PCB
6
PLLS w/ INTEGRATED VCO - SMT
The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
6 - 42
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC783LP6CE
v02.0110
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 11.5 - 12.5 GHz
List of Materials for Evaluation PCB 127272 [1]
Item J1 J2, J3 JP1 - JP6 C1, C21, C38 - C39, C60 C2, C5, C6, C8, C10, C13, C16, C19, C22, C24, C26, C51, C55 C3, C7, C9, C11, C12, C14, C18, C20, C23, C25, C27 - C29, C34 - C36, C40 - C43, C46, C50, C52, C54, C56 C4, C17, C32, C45, C48, C49, C53, C68, C74 C15, C31 C44, C67 C33 C37 C47, C73 C57 C58, C59 C61 FB1 - FB4 R1, R8 R2, R7 R3, R17, R20, R41 R4 R5, R14, R15, R18, R19 R6 R9 R10, R22, R23 R11, R16, R40 R13 R21 TP1 - TP6 U1 U2, U4, U6 U5 U8, U9 Y2 PCB [2] Description Dual Row Terminal Strip PCB Mount SMA RF Connector Single Row Terminal Strip 1000 pF Capacitor, 0402 Pkg. 10 pF Capacitor, 0402 Pkg.
0.1 F Capacitor, 0402 Pkg.
4.7 F Capacitor, 0805 Pkg. 100 pF Capacitor, 0402 Pkg. 1200 pF Capacitor, 0402 Pkg. 1500 pF Capacitor, 0402 Pkg. 0.039 F Capacitor, 0603 Pkg. 10,000 pF Capacitor, 0402 Pkg. 22 F Tantalum Capacitor, Case D 4.7 F Tantalum Capacitor, Case B 3900 pF Capacitor, 0402 Pkg. 1000 Ohm 200 mA Ferrite Chip, 0805 Pkg. 100k Ohm Resistor, 0402 Pkg. 120 Ohm Resistor, 0402 Pkg. 1k Ohm Resistor, 0402 Pkg. 620 Ohm Resistor, 0402 Pkg. 10k Ohm Resistor, 0402 Pkg. 56 Ohm Resistor, 0402 Pkg. 10 Ohm Resistor, 0402 Pkg. Zero Ohm Resistor, 0402 Pkg. 4.02k Ohm Resistor, 0402 Pkg. 182 Ohm Resistor, 0402 Pkg. 30 Ohm Resistor, 0402 Pkg. Test Point PC Compact SMT HMC783LP6CE Fractional-N Synthesizer, with Integrated VCO Low Noise 3.3V, 100 mA Linear Regulator Low Noise Op-Amp, THS4031IDGN 5V, 800mA Voltage Regulator 3.3V, 50 MHz VCXO Crystal Oscillator 125536 Evaluation Board
6
PLLS w/ INTEGRATED VCO - SMT
6 - 43
[1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com

▲Up To Search▲

Price & Availability of HMC783LP6CE10

	To Download HMC783LP6CE10 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .