PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST
TITLE : HV089WX1-100 HV089WX1 100 Product Specification for Customer Rev. O
FOR MORE INFORMATION:
AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com
BOE HYDIS TECHNOLOGY
SPEC. NUMBER B2005-C001-B (1/3)
PRODUCT GROUP TFT-LCD
REV. O
ISSUE DATE 2008.2. 11
PAGE 1 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV O
ISSUE DATE 2008.2.11
REVISION HISTORY
REV. O ECN NO. DESCRIPTION OF CHANGES Initial Release DATE 2008.02.11 PREPARED Joseph Ha
SPEC. NUMBER B2005-C001-B (2/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 2 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV O
ISSUE DATE 2008. 2.11
Contents
No 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 General Description Absolute Maximum ratings Electrical specifications Optical specifications Interface Connection Signal Timing Specification Signal Timing waveforms of interface signal (DE mode) Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Mechanical Drawing Reliability Test Handling & Cautions Environment & Safety Packing Information Item Page 4 6 7 9 14 17 17 19 20 21 22 24 24 26 28
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 3 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 1.0 GENERAL DESCRIPTION
1.1 Introduction
REV O
ISSUE DATE 2008. 2.11
HV089WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 8.9 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 768 vertical pixel array) Each pixel is divided into RED GREEN BLUE dots which are array). RED, GREEN, arranged in vertical stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type.
LVDS Input Signal Si l
1 CN Connector (C 1 )
Source Driver LCDS Rx + T/CON Gate Driver
VDD
DC/DC Gamma Vcom
TFT LCD Panel BACK LIGHT (Fluorescent Lamp) 1280 X 768
HVDD VDIM Back Light (SMD LED Array)
CN2
1.2 Features Thin and light weight 3.3 V power supply Low driving voltage and low power consumption 1 Channel LVDS Interface SMD LED (36EA) Array (Top Side/Horizontal Direction) 262,144 colors Data enable signal mode Front Mounting Frame RoHS Product No EDID and No LED driver
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 4 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
1.3 Application Tablet PC
REV O
ISSUE DATE 2008. 2.11
1.4 General Specifications
T bl 1 G lS ifi ti Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Luminance of White Weight Back-light Specification 193.92 (H) x116.35 (V) 1280 (H) x768 (V) 0.1515 (H) x0.1515 (V) 0.1515 RGB Vertical stripe 262,144 Normally Black 206.60.3(W) x133.00.3(V) x 5.25 (D/Max) () () (/ ) 300 (Typ.) mm Cd/m Note 1 At Center colors Unit mm pixels mm Remarks
130(Typ.) 5 (Min. / Max.) SMD LED (36EA) Array
g
Note 1: at PCB side
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 5 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 2.0 ABSOLUTE MAXIMUM RATINGS
REV O
ISSUE DATE 2008. 2.11
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit.
Ta=25+/-2C
Parameter Logic P L i Power Supply Voltage S l Vl Logic Power Supply Voltage Back-light Power Supply Voltage Back-light LED Current 25 50 Back-light LED Reverse Voltage Operating Temperature Storage Temperature
Symbol VDD VIN HVDD ILED ILED VR TOP TSP
Min. -0.3 03 -0.3 -0.3 0 -20
Max. 4.0 40 VDD+0.3 40 30 20 5 +50 +60
Unit V V V mA mA V
Remarks
Note 1
Note 1, 2
Note 1 Ambient temperature vs allowable forward current are shown in the figure below 1. below. Note 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40 Ta) Maximum wet - bulb temperature at 39 or less. ( > 40) No condensation.
Relative Humudity
Ambient Temperature vs Maximum Forward Current
100 90 80 (40, 90)
(50,20)
60
Operating Range p g g
(50, 50)
40 (60, 27) 20 5 -40 -20 0 20 40 60 80
Storage Range
Temperature ()
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 6 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 3.0 ELECTRICAL SPECIFICATIONS
3.1 Electrical Specifications Parameter Logic Power Supply Voltage Logic Power Supply Current Back-light Anode Supply Voltage Back-light Cathode Supply Voltage Back-light PWM Frequency g q y High Level Differential Input Signal Voltage Low Level Differential Input Signal Voltage Back-light LED Voltage / Back-light LED Total Voltage Back-light LED Current / Back-light LED Total Current Life Time PD Power Consumption Power Consumption (EBL) PLED Ptotal PEBL VDD IDD Vanode Vcathode FPWM VIH VIL VLED /VBL ILED /IBL
< Table 3. Electrical Specifications >
REV O
ISSUE DATE 2008. 2.11
Min. 3.0 100 -100
2.7/ 16.2 16 2
Typ. 3.3 330 19.2 0 3.2/ 19.2 19 2 16/ 96 1.09 1.84 1 84 2.84 1.46
Max. 3.6 500 25.8 4.8 500 +100 3.5/ 21.0 21 0 16.8/ 100.8 1.65 2.12 2 12 3.77 1.51
Unit V mA V V mV mV V mA Hrs W W W W
Remarks
Note 1 Note 1 Note 2 Note 2
VCM = +1.2V
15.2/ 91.2
12,000
Based on LED Note 1 Note 2 3 2, Note 1, 2, 3 Note 1, 2, 3
-
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25. a) Typ : Window XP pattern ) d b) Max : Vertical Sub line pattern c) EBL : Mosaic pattern (32 x 32) 2. The power supply voltage and current is measured and specified at the interface connector of LCM including LED Driver. 3. Reference value, which is measured with LED Driver for 12V. 4. Reference value, which is measured without LED Driver. 5. Calculated value for reference (VLED x ILED x # of LEDs (36EA) ).
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 7 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 4.0 OPTICAL SPECIFICATION
4.1 Overview
REV O
ISSUE DATE 2008. 2.11
The test of Optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 252) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. We refer to O=0 (=3 ) as the 3 o'clock direction (the "right"), O=90 (= 12 ) as the 12 o'clock direction ("upward"), O=180 (= 9 ) as the 9 o'clock direction ("left") and O=270(= 6 ) as the 6 o'clock direction ("bottom"). While scanning and/or O, the center of the measuring O 270 spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25C. Optimum viewing angle direction is 6 o'clock.
4.2 Optical Specifications
Parameter Viewing Angle range Horizontal Vertical Symbol 3 9 12 6 CR Yw Y5 Y13 xw yw xR yR Reproduction Of color Green Blue Response Time Cross Talk Rise Decay xG yG xB yB Tr Td CT Ta= 25 C = 0 = 0 = 0 = 0 = 0 = 0 CR > 10 Condition Min. 85 85 85 85 450 270 80 60 0.260 0.280 0.523 0.314 0.291 0.502 0 502 0.106 0.077 Typ. 89 89 89 89 500 300 85 70 0.300 0.320 0.563 0.354 0.331 0.542 0 542 0.146 0.117 28 Max. 90 90 90 90 0.340 0.360 0.603 0.394 0.371 0.582 0 582 0.186 0.157 2.0 ms % Note 5 Note 6 cd/m2 % Note 3 Note 4 Unit Deg. Deg. Deg. Deg. Note 2 Note 1 Remark
Luminance Contrast ratio Luminance of White White Luminance uniformity 1 Point 5 Points 13 Points
White Chromaticity Red
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 8 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT Note :
REV O
ISSUE DATE 2008. 2.11
1.
2.
Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o'clock direction and the vertical or 6, 12 o'clock direction with respect to the optical axis which is normal to the LCD surface. ( see FIGURE 1 shown in Appendix ) Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. Luminance when displaying a white raster Luminance when displaying a black raster
CR =
3. 4. 4 5. 6.
The White luminance uniformity on LCD surface is then expressed as : Y = Maximum Luminance of 5(or 13) points / Minimum Luminance of 5(or 13) points. ( see FIGURE 2 shown in Appendix ) The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the "data" input signal OFF and ON. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the l i h luminance (YA) of a 25 f 25mm di diameter area, with all di l pixels set to a gray l i h ll display i l level, to l the luminance (YB) of that same area when any adjacent area is driven dark. ( see FIGURE 4 shown in Appendix )
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 9 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
4.3 Optical Measurements
Figure 1. Measurement Set Up
Photo detector ( TOPCON BM-5A)
REV O
ISSUE DATE 2008. 2.11
Field = 1 TFT-LCD module
o
50 cm LCD panel
Center of the screen
Optical characteristics measurement setup Figure 2. White Luminance and Uniformity Measurement Locations (5 points)
Column Row 192 320 640 960
384
576
Note 4 N 4. Luminance of white is defined as luminance values of 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 2 for a total of the measurements per display. * Yw = (Sum of 5 Points Luminance / 5 ) * LED Condition = (Duty Ratio 100%, LED current 16.0mA)
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 10 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV O
ISSUE DATE 2008. 2.11
Figure 3. Uniformity Measurement Locations (13 points) 3
192
384
576
Note 5. The White luminance uniformity on LCD surface is then expressed as : Y5 = (Minimum Luminance of five points / Maximum Luminance of five points) X 100% (see Figure 2) , Y13 = (Minimum Luminance of 13 points /Maximum Luminance of 13 points) X 100% (see Figure 3).
Figure 4. Response Time Testing g p g
TFT Off(Black)
TFT On(White)
TFT Off(Black)
Tr
Td
100% 90% 10% 0%
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 11 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
Figure 5. Cross Modulation Test Description VIEW AREA VIEW AREA 320,192 L31 320,576 YA (1120, 384) Cross-Talk (%) = YB - YA YB x 100 L0
REV O
ISSUE DATE 2008. 2.11
960,192 YB(1120, 384) 960,576
Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns Note 6. The electro-optical response time measurements shall be made as Figure 4 by switching the "data" input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. Note 7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark (Refer to Figure 5).
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 12 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 5.0 INTERFACE CONNECTION.
5.1 Electrical Interface Connection
REV O
ISSUE DATE 2008. 2.11
CN1 CN2 Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Interface connector FPC connector Symbol VDD1 VDD2 VDD3 VDD4 NC VSS VSS VSS VSS RIN0RIN0+ 0 VSS RIN1RIN1+ VSS RIN2RIN2+ VSS RCLKINRCLKIN+ VSS NC VCD1 VCD2 VCD3 VCD4 VCD5 VCD6 NC VAD I-PX / 20347-030E-02 or equivalent I-PEX / 20397-008E or equivalent Function +3.3V +3.3V +3.3V +3.3V Remark
Power Supply: Power Supply: Power Supply: Power Supply: Reserved Ground Ground Ground Ground LVDS Negative data signal (-) LVDS Positive data s g a ( ) S os t e signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative clock signal (-) LVDS Positive clock signal (+) Ground Reserved LED Power Cathode LED Power Cathode LED Power Cathode LED Power Cathode LED Power Cathode LED Power Cathode Reserved LED Power Anode
Tx pin # 48 Tx pin # 47 p Tx pin # 46 Tx pin # 45 Tx pin # 42 Tx pin # 41 Tx pin # 40 Tx pin # 39
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 13 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
5.2. LVDS Interface LVDS Transmitter: THC63LVDM83A or equivalent.
Input signal R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 HSYNC VSYNC DE MCLK Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 9 20 22 23 24 27 28 30 31 40 39 CLKOUTCLKOUT CLKOUT+ CLKINCLKIN CLKIN+ 42 41 OUT2OUT2+ IN2IN2+ 46 45 OUT1OUT1+ IN1IN1+ 48 47 OUT0OUT0+ IN0IN0+ Pin No Interface System (Tx) TFT-LCD (Rx)
REV O
ISSUE DATE 2008. 2.11
DF19KR-20P-1H Pin No.
Remark
10 11
13 14
16 17
19 20
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 14 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
5.3 Back-light Interface g
CN2 Pin No. 1 2 3 4 5 6 7 8 9
REV O
ISSUE DATE 2008. 2.11
LED FPC Connector (20397-008E, Manufactured by I-PEX ) Symbol Anode1 Anode2 Anode3 Anode4 NC Cathode1 Cathode2 Cathode3 Cathode4 Function LED Anode Power Supply LED Anode Power Supply LED Anode Power Supply LED Anode Power Supply Non-Connection LED Cathode Power Supply LED Cathode Power Supply LED Cathode Power Supply LED Cathode Power Supply LED Cathode Power Supply LED Anode Power Supply pp y (3.2V X 6 EA = 19.2V) Remark
5.4. Data Input Format
(1,1) (1,2) (1279,1) (1280,1) RGBRGB
RGBRGB
1 Pixel = 3 Dots
RGB
RGBRGB (1,768) (2,768)
RGBRGB (1279,768) (1280,768)
Display position of input data
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 15 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 6.0. 6 0 SIGNAL TIMING SPECIFICATIONS
REV O
ISSUE DATE 2008. 2.11
6.1 HV089WX1-100 is operated by the only DE (Data enable) mode (LVDS Transmitter Input)
Item Frame Period Vertical Display Period One Line Scanning Period Horizontal Display Period Clock Frequency Symbols T1 T2 T3 T4 1/T5 Min 804 1350 Typ 823 768 1440 1280 71.11 Max Unit lines lines clocks clocks MHz
7.0 SIGNAL TIMING WAVEFORMS
7.1 7 1 Timing Waveforms of Interface Signal
T1 T2 DE
T3 DCLK T5 DE DATA SIGNALS T4
Valid display data (1280 Clocks)
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 16 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
7.2 LVDS Rx Interface Timing Parameter
The specification of the LVDS Rx interface timing parameter < LVDS Rx Interface Timing Specification>
REV O
ISSUE DATE 2008. 2.11
Item CLKIN P i d Period Input Data 0 Input Data 1 Input Data 2 Input Data 3 Input Data 4 Input Data 5 Input Data 6
Symbol tRCIP tRIP0 tRIP1 tRIP2 tRIP3 tRIP4 tRIP5 tRIP6
Min. 12.50 12 50 -0.4 tRICP/7-0.4
Typ. 14.43 14 43 0.0 tRICP/7
Max. 25.00 25 00 +0.4 tRICP/7+0.4
Unit Remarks nsec nsec nsec
2 xtRICP/7-0.4 2 xtRICP/7 2 xtRICP/7+0.4 nsec 3 xtRICP/7 0 4 3 xtRICP/7 3 xtRICP/7+0 4 nsec xtRICP/7-0.4 xtRICP/7+0.4 4 xtRICP/7-0.4 4 xtRICP/7 4 xtRICP/7+0.4 nsec 5 xtRICP/7-0.4 5 xtRICP/7 5 xtRICP/7+0.4 nsec 6 xtRICP/7-0.4 6 xtRICP/7 6 xtRICP/7+0.4 nsec
tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 tRIP1 tRIP0 RxINz +/* Z = 0, 1, 2 RxCLKIN+/Rx Rx Rx Rx Rx Rx Rx Rx Rx Rx Rx
Vdiff=0[v] tRCIP
Vdiff=0[v]
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 17 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV O
ISSUE DATE 2008. 2.11
8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS
Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data.
Colors & Gray Scale
Black Blue Green Basic Colors Cyan Red Magenta Yellow White Black Gray Scale Of Red Darker Brighter Red Black Gray Scale Of Green Darker Brighter Green G Black Gray Scale Of Blue Darker Brighter Blue Black Gray Scale Of White & Black Darker Brighter White 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 1 1 1 0 1
Red Data R5
0 0 0 0 1 1 1 1 0 0 0
Green Data R1
0 0 0 0 1 1 1 1 0 0 1
Blue Data G1
0 0 1 1 0 0 1 1 0 0 0
R4
0 0 0 0 1 1 1 1 0 0 0
R3
0 0 0 0 1 1 1 1 0 0 0
R2
0 0 0 0 1 1 1 1 0 0 0
R0
0 0 0 0 1 1 1 1 0 1 0
G5
0 0 1 1 0 0 1 1 0 0 0
G4
0 0 1 1 0 0 1 1 0 0 0
G3
0 0 1 1 0 0 1 1 0 0 0
G2
0 0 1 1 0 0 1 1 0 0 0
G0
0 0 1 1 0 0 1 1 0 0 0
B5
0 1 0 1 0 1 0 1 0 0 0
B4
0 1 0 1 0 1 0 1 0 0 0
B3
0 1 0 1 0 1 0 1 0 0 0
B2
0 1 0 1 0 1 0 1 0 0 0
B1
0 1 0 1 0 1 0 1 0 0 0
B0
0 1 0 1 0 1 0 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
1 1 1 0 0 0
0 1 1 0 0 1
1 0 1 0 1 0
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 18 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 9.0 POWER SEQUENCE Q
REV O
ISSUE DATE 2008. 2.11
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below
0.9VDD 0 9VDD
Power Supply
0V
0.9VDD 0.1VDD
0.1VDD
T1 T2
T5
T7 T6
Interface Signal
Valid
0V
T3
T4
Back- light
0V
0 < T1 10 ms 0 < T2 50 ms 200 ms T3 200 ms T4 0 T5 50ms 0 T6 10ms 150ms T7
Notes:
1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. g p g g
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 19 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 10.0 MECHANICAL CHARACTERISTICS
10.1 Dimensional Requirements
REV O
ISSUE DATE 2008. 2.11
FIGURE 5, 6 shown in appendix shows mechanical outlines for the model.
Parameter Active area Number of pixels Specification 193.92 (H) x116.35 (V) 1280(H) x768(V) (1 pixel = R + G + B dots) Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Back-light 0.1515(H) x0.1515(V) RGB Vertical stripe 262,144 Normally Black 206.60.3(W) x133.00.3(V) x 5.25 (D/Max) 130 (Typ.) SMD LED (36ea) Array
mm g colors mm
Unit
mm pixels
10.2 Mounting See FIGURE 5. (shown in Appendix) 10.3 Glare and Polarizer Hardness. The surface of the LCD has an glare coating and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50 cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable.
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 20 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 11.0 Mechanical Drawing
REV O
ISSUE DATE 2008. 2.11
Figure 6. TFT-LCD Module Outline Dimension (Front View)
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 21 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV O
ISSUE DATE 2008. 2.11
Figure 7. TFT LCD Module Outline Dimensions (Rear view) TFT-LCD
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
10
PAGE 22 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV O
ISSUE DATE 2008. 2.11
12.0 RELIABLITY TEST The Reliability test items and its conditions are shown in below.
No 1 2 3 4 5 6 7 Test Items High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Thermal shock Vibration test (non-operating) Shock test (non-operating) Electro-Static Discharge Test (non-operating) (non operating) Conditions Ta = 60 C, 240 hrs C, Ta = -20 C, 240 hrs Ta = 50 , 80%RH, 240hrs Ta = 50 C, 240 hrs Ta = 0 C, 240 hrs Ta = -20 C 60 C (30 min), 100 cycle Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min Gravity : 220G Pulse width : 2ms, half sine wave X, Y, Z Once for each direction Air : 150pF, 330ohm, 15KV Contact : 150pF 330ohm 8KV 150pF, 330ohm,
8
9
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 23 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 13.0 HANDLING & CAUTIONS
REV O
ISSUE DATE 2008. 2.11
13.1 Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. 13.2 Cautions for handling the module As the electrostatic discharges may break the LCD module handle the LCD module module, with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and backlight element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. 13.3 Cautions for the operation When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence were applied, the module would be damaged. 13.4 Cautions for the atmosphere Dewdrop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. St t h Storage i an electro-conductive polymer-packing pouch and under in lt d ti l ki hdd relatively low temperature atmosphere is recommended. 13.5 Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. 13.6 Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc, please pack the module not to be broken. We recommend using the original shipping packages.
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 24 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 14.0 Environment & Safety
14.1 Packing Label Label Size: 108 mm (L) x 56 mm (W) Contents Model: HV089WX1-100 Qty: Module Qty in one box Serial No.: Box Serial No. See next figure for detail description. Date: Packing Date FG Code: FG Code of Product
REV O
ISSUE DATE 2008. 2.11
HV089WX1-100 * 0000000000000 *
XX 200X.X.XX
XXXX
00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no
FG CODE
RoHS Mark
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 25 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
14.3 Product Label
REV O
ISSUE DATE 2008. 2.11
10
BOE HYDIS Barcode 1 X X 2 X 3 X 4 X 5 X X 6 XX X X X 7 X X X
No 1. Control Number No 2. Rank / Grade
No 5. Month (1, 2, 3,..., 9, X, Y, Z) No 6. Product name
No 3. Line Classification No 7. Serial Number (BOE HYDIS : H, LCM : L, BOE OT : A/B/C) No 4. Year (7 : 2007, 8 : 2008, ...)
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 26 OF 27 A4(210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 15.0 PACKING INFORMATION
15.1 Packing Order
REV O
ISSUE DATE 2008. 2.11
Put Pad into the box.
Put silica gels in the box.
After sealing the box, attach Packing Label on the attach position sign area of the box.
Place a cover on the top of the box. As shown in the f figure, place the Modules bundled by shielding bag in the box.
Notes Box Dimension : 261mm(W) X 349mm(D) X 311mm(H) Package Q Pk Quantity i one Box : 20 tit in B 20pcs
SPEC. NUMBER B2005-C001-B (3/3)
SPEC. TITLE HV089WX1-100 Product Specification for Customer
PAGE 27 OF 27 A4(210 X 297)
| |
Price & Availability of HV089WX1-100
 |
|
|
|
|
|
All Rights Reserved ©
IC-ON-LINE 2003 - 2022 |
.
.
.
.
.
| |
We use cookies to deliver the best possible
web experience and assist with our advertising efforts. By continuing to use
this site, you consent to the use of cookies. For more information on
cookies, please take a look at our
Privacy Policy. |
X |
|
