|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
VL-821 CMOS Crystal Oscillator Previous Vectron Model VCS3 VL-821 Description Vectron's VL-821 Crystal Oscillator (XO) is a quartz stabilized square wave generator with a CMOS output, operating off either a 1.8, 2.5, or 3.3 volt supply. The VL-821 utilizes a high performance, low frequency quartz resonator followed by a custom ASIC to synthesize the output frequency. Features * * * * * * * * Applications * * * * * * SONET/SDH/DWDM Ethernet, GE, SynchE Storage Area Networking Digital Video Broadband Access Microprocessors/DSP/FPGA Quick delivery CMOS Output 3.2mm x 2.5mm x 1.2mm Output frequencies to 200.00 MHz Tri-state output for the board test and debug -10/70C or -40/85C operating temperature Gold over nickel contact pads Product is compliant to RoHS directive and fully compatible with lead free assembly Block Diagram VDD Crystal Output Osc PLL E/D Gnd Page1 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Performance Specifications Table 1. Electrical Performance, 3.3V Option Parameter Operating Supply Voltage 1 Symbol VDD IDD Min Supply 2.97 -0.05 Typical 3.3 Maximum 3.63 5.0 10 15 20 25 Units V V mA Absolute Maximum Operating Voltage Supply Current, Output Enabled <30 MHz 30.01 to 75 MHz 75.01 to 133 MHz 133.01 to 200 MHz Supply Current, Output disable Frequency Stability , (Ordering Option) 4 IDD Frequency fO 1.000 25, 50, 100 Outputs 15 200.00 uA MHz ppm Output Logic Levels Output Logic High2 Output Logic Low2 Output Logic High Drive Output Logic Low Drive Output Rise /Fall Time2, fo10MHz fo>10MHz Duty Cycle3 Output Enable/Disable Output Enable Output Disable Start-Up Time Operating Temp, (Ordering Option) 1] 2] 3] 4] 5] 5 VOH VOL IOH IOL tR/tF SYM 0.9*VDD 0.1*VDD 8 8 3 2 45 Enable/Disable 50 55 V V mA mA ns ns % VIH VIL tSU TOP 0.7*VDD 0.3V*DD 2 -10/70 or -40/85 V V ms C A 0.01 uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground). VDD supply ramp should be <100 msec. Figure 2 defines these parameters. Figure 1 illustrates the operating conditions under which these parameters are tested and specified. Symmetry is measured defined as On Time/Period. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under operation). Output will be enabled if the Enable/Disable is left open. E/D should be powered up after VDD. tR IDD + VDD 4 .1F .01F 1 + Period Fig 1: Test Circuit Fig 2: Waveform tF VOH 3 2 15pF 50% VOL On Time Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page2 Performance Specifications Table 2. Electrical Performance, 2.5V Option Parameter Operating Supply Voltage 1 Symbol VDD IDD Min Supply 2.25 -0.5 Typical 2.5 Maximum 2.75 5 8.0 10.0 15.0 Units V V mA Absolute Maximum Opertaing Voltage Supply Current, Output Enable <30 MHz 30.01 to 75 MHz 75.01 to 166 MHz Supply Current, Output Disabled 0.7VDD Frequency Stability4, (Ordering Option) IDD Frequency fO 1.000 25, 50, 100 Outputs 15 166.000 uA MHz ppm Output Logic Levels Output Logic High2 Output Logic Low2 Output Logic High Drive Output Logic Low Drive Output Rise /Fall Time2, fo10MHz fo>10MHz Duty Cycle3 Output Enable/Disable5 Output Enable Output Disable Start-Up Time Operating Temp, (Ordering Option) 1] 2] 3] 4] 5] VOH VOL IOH IOL tR/tF SYM 0.9*VDD 0.1*VDD 8 8 4 3 45 Enable/Disable 50 55 V V mA mA ns ns % V VIH VIL tSU TOP 0.7*VDD 0.3*VDD 2 -10/70 or -40/85 ms C A 0.01 uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground). VDD supply ramp should be <100 msec. Figure 2 defines these parameters. Figure 1 illustrates the operating conditions under which these parameters are tested and specified. Symmetry is measured defined as On Time/Period. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under operation). Output will be enabled if the Enable/Disable is left open. E/D should be powered up after VDD. tR IDD + 4 .1F .01F IC VC Fig 1: Test Circuit tF VOH 3 2 15pF 1 + Period Fig 2: Waveform VDD 50% VOL On Time Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page3 Performance Specifications Table 3. Electrical Performance, 1.8V Option Parameter Operating Supply Voltage 1 Symbol VDD IDD Min Supply 1.62 -0.5 Typical 1.8 Maximum 1.98 3.6 6 8 12 Units V V mA Absolute Maximum Voltage Supply Current, Output Enabled <30 MHz 30.01 to 75 MHz 75.01 to 133 MHz Supply Current, Output Disabled Frequency Stability4, (Ordering Option) IDD Frequency fO 1.000 25, 50, 100 Outputs 15 133.00 uA MHz ppm Output Logic Levels Output Logic High2 Output Logic Low2 Output Logic High Drive Output Logic Low Drive Output Rise /Fall Time2,, fo 10MHz fo>10MHz Duty Cycle3 Output Enable/Disable Output Enable Output Disable Start-Up Time Operating Temp, (Ordering Option) 1] 2] 3] 4] 5] 5 VOH VOL IOH IOL tR/tF SYM 0.9*VDD 0.1*VDD 8 8 5 4 45 Enable/Disable 50 55 V V mA mA ns ns % VIH VIL tSU TOP 0.7*VDD 0.3*VDD 2 -10/70 or -40/85 V V ms C A 0.01 uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground). VDD supply ramp should be <100 msec. Figure 2 defines these parameters. Figure 1 illustrates the operating conditions under which these parameters are tested and specified. Symmetry is measured defined as On Time/Period. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under operation). Output will be enabled if the Enable/Disable is left open. E/D should be powered up after VDD. tR IDD + VDD 4 .1F .01F IC VC Fig 1: Test Circuit tF VOH 3 2 15pF 50% VOL On Time Period Fig 2: Waveform 1 + Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page4 Outline Drawing & Pad Layout Table 4. Pin Out Pin 1 2 3 4 Symbol E/D GND fO Function Enable Disable Case and Electrical Ground Output Frequency Power Supply Voltage VDD Reliability VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The VL-821 family is capable of meeting the following qualification tests: Table 5. Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Gross and Fine Leak Resistance to Solvents Moisture Sensitivity Level Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 1010 MIL-STD-883, Method 2003 MIL-STD-883, Method 1014 MIL-STD-883, Method 2015 MSL 1 Contact Pads Gold over Nickel Typical Characteristics - Phase Noise and Gain Curve Although ESD protection circuitry has been designed into the VL-821 proper precautions should be taken when handling and mounting. VI employs a human body model (HBM) and a charged device model (CDM) for ESD susceptibility testing and design protection evaluation. Table 6. ESD Ratings Model Human Body Model Charged Device Model Minimum 1500V 1000V Conditions MIL-STD-883, Method 3115 JESD 22-C101 Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Permanent damage is also possible if E/D is applied before VDD. Table 7. Absolute Maximum Ratings Parameter Storage Temperature Soldering Temp/Time Symbol TS TLS Ratings -55 to 125 260 / 20 Unit C C / sec Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page5 IR Reflow The VL-821 is qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The VL-821 device is hermetically sealed so an aqueous wash is not an issue. Table 8. Reflow Profile Parameter PreHeat Time Ts-min Ts-max Ramp Up Time Above 217 C Time To Peak Temperature Time at 260 C Ramp Down Symbol tS Value 60 sec Min, 260 sec Max 150C 200C 3 C/sec Max 60 sec Min, 150 sec Max 480 sec Max 10 sec Max 6 C/sec Max RUP tL TAMB-P tP RDN Tape and Reel Table 9. Tape and Reel Information Tape Dimensions (mm) Dimension Tolerance VL-821 Reel Dimensions (mm) Po Typ 4 W Typ 8 F Typ 3.5 Do Typ 1.5 P1 Typ 4 A Typ 180 B Min 2 C Typ 13 D Min N Min 60 W1 Typ 8 W2 Typ 12 # Per Reel 1000 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page6 Table 10. Standard Output Frequencies (MHz) 1.000 14.746 33.000 44.000 80.000 150.000 1.544 19.6608 33.333 45.000 98.5382 155.520 2.048 24.49219 33.554 48.000 106.25 156.000 2.176 24.576 36.000 49.152 110.00 156.250 7.3728 25.000 37.056 50.000 124.444 160.000 8.000 26.660 40.000 61.440 125.000 162.000 10.000 27.000 42.660 65.000 133.000 170.000 11.0592 30.000 43.000 66.666 135.000 200.000 Ordering Information VL-821- E A W- K A A N- xxMxxxxxxx Product PLL Crystal Oscillator Package 3.2x5 Ceramic Power Supply E: +3.3Vdc H: +2.5Vdc J: +1.8Vdc Output A: CMOS Temp Range W: -10/70C E: -40/85C *Note: not all combination of options are available. Other specifications may be available upon request. Frequency in MHz Custom Options N: Standard Option Load A: 15pF Enable/Disable A: Enable/Disable, Enable High Stability F: 25ppm K: 50ppm S: 100ppm Example: VL-821-EAW-KAAN-125M000000 For Additional Information, Please Contact USA: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Asia: Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 7/24/2009 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page7 |
Price & Availability of VL-821-HAE-SA |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |