 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| D100VHI Series Miniature, 1W SIP Ultra-High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: * 1W Output Power * 6.0 kVDC Isolation * Miniature SIP Case * Single & Dual Outputs * Miniature SIP Case * 12 Standard Models * 2.0 MH MTBF * Industry Standard Pin-Out Input Parameter Input Voltage Range Input Filter Reverse Polarity Input Current Conditions 5 VDC Input 12 VDC Input Min. 4.5 10.8 Typ. 5.0 12.0 Max. 5.5 13.2 0.3 Conditions Dual Output , Balanced Loads For Vin Change of 1% Min. Typ. 1.0 0.1 1.2 100 Over Line, Load & Temp. 120 0.01 Momentary (0.5 Sec.) Conditions 60 Seconds Flash Tested For 1 Sec 500 VDC 100 kHz, 1V 50 Conditions Ambient Case Min. -40 -40 -40 Free Air Convection RH, Non-condensing 95 % Min. 6,000 6,600 10 15 80 Typ. +25 20 100 Max. +70 +90 +125 Typ. Max. Units VDC VDC G pF kHz Units C C C 0.02 Max. 3.0 1.0 1.5 150 200 5 Units VDC Internal Capacitor A Units % % % mV P - P mV P - P mV rms % %/C Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit See Model Selection Guide RoHS Compliant General Parameter Isolation Voltage Isolation Test Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Cooling Humidity Physical Case Size Case Material Weight 0.87 x 0.49 x 0.30 Inches (22.0 x 12.5 x 7.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.13 Oz (3.9g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 2.0 Min. -0.7 -0.7 Typ. Max. 9.0 18.0 260 650 Typ. Max. Units MHours Units VDC C mW Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Input Model Number D101VHI D102VHI D103VHI D104VHI D105VHI D106VHI D111VHI D112VHI D113VHI D114VHI D115VHI D116VHI Voltage (VDC) Nominal 5 5 5 5 5 5 12 12 12 12 12 12 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 Output Load Voltage Current Current Regulation Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) Current (mA) 303 291 295 303 267 287 126 121 123 126 108 117 55 55 55 55 55 55 30 30 30 30 30 30 5.0 12.0 15.0 5.0 12.0 15.0 5.0 12.0 15.0 5.0 12.0 15.0 200.0 80.0 65.0 100.0 40.0 35.0 200.0 80.0 65.0 100.0 40.0 35.0 4.0 2.0 1.0 2.0 1.0 1.0 4.0 2.0 1.0 2.0 1.0 1.0 10 8 8 10 8 8 10 8 8 10 8 8 Efficiency (%, Typ) 66 66 66 66 72 73 66 66 66 66 74 75 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 200 200 200 200 200 200 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recomended that an external 0.33 F ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin 1 2 5 6 7 Single +Vin -Vin -Vout No Pin +Vout Dual +Vin -Vin -Vout Common +Vout NC: No Connection Capacitive Load Single Output F Max 680 Dual Output F Max 220 Mechanical Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of D106VHI
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |