View PSP-500_4333588.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

500W with PFC and Parallel Function
Features :
PSP-500
Universal AC input / Full range Built-in active PFC function, PF>0.95
series
Protections: Short circuit / Overload / Over voltage / Over temperature Foced air cooling by built-in DC fan Current sharing up to 2000W(3+1) With power good and fail signal output Built-in remote ON-OFF control Built-in remote sense function 3 years warranty
SPECIFICATION
MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE FUNCTION REMOTE CONTROL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & EMC
(Note 4)
PSP-500-5 5V 80A 0 ~ 80A 400W 4.75 ~ 5.5V 2.0% 0.5% 2.0% 24ms at full load
Note.6 90 ~ 264VAC
PSP-500-12 12V 41.5A 0 ~ 41.5A 498W 150mVp-p 10 ~ 13.2V 1.0% 0.3% 0.5%
PSP-500-13.5 13.5V 37A 0 ~ 37A 499.5W 150mVp-p 12 ~ 15V 1.0% 0.3% 0.5%
PSP-500-15 15V 33A 0 ~ 33A 495W 150mVp-p 13.5 ~ 18V 1.0% 0.3% 0.5%
PSP-500-24 24V 20.8A 0 ~ 20.8A 499.2W 150mVp-p 20 ~ 26.4V 1.0% 0.2% 0.5%
PSP-500-27 27V 18.5A 0 ~ 18.5A 499.5W 150mVp-p 24 ~ 30V 1.0% 0.2% 0.5%
PSP-500-48 48V 10.5A 0 ~ 10.5A 504W 200mVp-p 41 ~ 56V 1.0% 0.2% 0.5%
RIPPLE & NOISE (max.) Note.2 100mVp-p
1500ms, 50ms at full load 127 ~ 370VDC 0.98/100VAC at full load 82% 3.5A/230VAC 40A/230VAC 82% 82% 84% 84% 86%
47 ~ 63Hz 0.95/230VAC 76% 7A/115AVC 20A/115VAC <1mA / 240VAC 110 ~ 125% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V Protection type : Shut down o/p voltage, re-power on to recover RTH2 95 detect on heatsink of Q1,Q7 power transistor & L3 output choke Protection type : Shut down o/p voltage, recovers automatically after temperature goes down RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off sink current <4 ~ 10mA -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH with 30CFM forced air non-condensing -20 ~ +85 0.03%/ , 10 ~ 95% RH (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC / 70% RH
ISOLATION RESISTANCE HARMONIC CURRENT EMS IMMUNITY MTBF
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A 130.1K hrs min. MIL-HDBK-217F (25 ) 278*127*63.5mm (L*W*H) 2.6Kg; 6pcs/15.7Kg/0.89CUFT
OTHERS
DIMENSION PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. In parallel connection, maybe only one unit operated, if the total output load less than 5% of rated load condition. 6. Derating may be needed under low input voltages. Please check the derating curve for more details.
File Name:PSP-500-SPEC 2008-12-30
500W with PFC and Parallel Function
Mechanical Specification
220 16 19 max. 18 max.
PSP-500
Case No. 919A
127 113 7
series
Unit:mm
30
20
4-M3
5 4-M3 4-M3 Air flow direction 1 2 3 4 5 6 5 O/P
127
I/P 1 2 3
113
TOP VIEW
13
240
10
10
5 6 7 8
1 2 3 4
BOTTOM VIEW
7
7
LED
ADJ.
240 251 278
CONTROL
220
15
AC Input Terminal Pin No. Assignment
Pin No. 1 2 3 Assignment AC/L AC/N FG
DC Output Terminal Pin No. Assignment
Pin No. 1~3 4~6 Assignment DC OUTPUT +V DC OUTPUT -V
Control Pin No. Assignment : MOLEX 5559-NP uses 5558 male crimp terminal
Pin No. Assignment Pin No. Assignment Mating connector Terminal 1 5 P(Current share) NC MOLEX 5556 2 6 -S PF(Power fail signal) MOLEX 5557-NR Female crimp Terminal G +S 3 7 receptacle RCRC+ 4 8
CURRENT SHARING P PF +S +V -V -S
34.5 20 63.5
4-M3
Block Diagram
ACTIVE INRUSH CURRENT LIMITING RECTIFIERS & P.F.C.
FAN PF EMI FILTER POWER SWITCHING RECTIFIERS & FILTER O.C.P.
fosc : 134KHz
I/P
FG O.L.P. O.T.P. PWM CONTROL
DETECTION CIRCUIT O.V.P. +RC -RC
Derating Curve
Output Derating VS Input Voltage
12 ~ 48V
100
100 90
80
80
60
5V
70
LOAD (%)
40
LOAD(%)
0 10 20 30 40 50 60 (HORIZONTAL)
60 50 40
20
-10
90
115
135
180
230
264
AMBIENT TEMPERATURE ( )
INPUT VOLTAGE (V) 60Hz
File Name:PSP-500-SPEC 2008-12-30
500W with PFC and Parallel Function
Control terminal instruction manual
PF G +5V
PSP-500
series
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
-V -V -V +V +V +V LOAD + POWER SIGNAL
-V -V -V +V +V +V LOAD +
-V -V -V +V +V +V
DC 0~10V
LOAD +
Power Fail Signal
PF Signal is the voltage difference between "G" and "PF" pin output
Remote Sensing
Remote Control
Power ON: When V RC+ , RC- =0 ~ 0.8V or Open Power OFF: When V RC+ , RC- =4 ~ 10V
Parallel Operation
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
-V -V -V +V +V +V
-V -V -V +V +V +V
-V -V -V +V +V +V
LOAD +
Parallel Operation With Remote Sensing
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
-V -V -V +V +V +V
-V -V -V +V +V +V LOAD +
-V -V -V +V +V +V
DC 0~10V
Parallel Operation With Remote Control
File Name:PSP-500-SPEC 2008-12-30

▲Up To Search▲

Price & Availability of PSP-500

	To Download PSP-500 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .