View ML6204_4277089.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ML6204
ML6204 Series - High Speed LDO Regulators
(low ESR capacitor compatible, ON/OFF switch)
CMOS Low Power Consumption Dropout Voltage: 60mV @ 30mA, 200mV @ 100mA Maximum Output Current: 150mA Highly Accurate: 1.5V ~ 1.95V 3% 2.0V ~ 6.00V 2% Output Voltage Range: 1.5V ~ 6.0V Low ESR capacitor compatible
Applications
Mobile phones Cordless phones Cameras, video recorders Portable games Portable AV equipment Reference voltage Battery-powered equipment
General Description
The ML6204 series are highly precise, low noise, positive voltage LDO regulators manufactured using CMOS process. The series achieves high ripple rejection and low dropout and consists of a standard voltage source, an error correction, current limiter and a phase compensation circuit plus a driver transistor. Output voltage is selectable in 50mV increments within a range of 1.5V ~ 6.0V. The series is also compatible with low ESR ceramic capacitors which give added output stability. This stability can be maintained even during load fluctuations due to the excellent transient response of the series. The CE function enables the output to be turned off, resulting in greatly reduced power consumption.
Features
Maximum Output Current: 150mA Dropout Voltage: 200mV (IOUT = 100mA) Maximum Operating Voltage: 10V Output Voltage Range: 1.5V ~ 6.0V in 50mV increments Highly Accurate: 2% Low Power Consumption: TYP 70A Standby Current: less than 0.1A High Ripple Rejection: 70dB (10 kHz) Low Output Noise: 30Vrms Operational Temperature Range: -40C ~ +85C Low ESR Capacitor Compatible: Ceramic capacitor
Typical Application
P1/19
Rev. G, October 2006
ML6204
Pin Assignment
Pin Function
Pin No. SOT-23-5 1 2 3 4 5 SOT-89-5 4 2 3 1 5 VIN VSS CE N.C. VOUT Input Ground ON/OFF Control No Connection Output Pin Name Description
SOT-23-5
SOT-89-5
Product Classification Selection Guide The following options for the CE pin logic and internal pull-up/down are available: Active 'High' + no pull-down resistor built-in (standard) Active 'High' + 800k pull-down resistor built-in (semi-custom) Active 'Low' + no pull-up resistor built-in (semi-custom) Active 'Low' + 800k pull-up resistor built-in (semi-custom)
Note: *With the pull-up resistor or pull-down resistor built-in types, the supply current during operation will increase by VIN / 800k (TYP.)
Ordering Information ML62041234567 Designator Symbol A 1 B C D 23 15 ~ 60 2 4 A 5 6 7 M P R L G
Description Active "High" (pull-down resistor built in) Active "High" (no pull-down resistor built in) Active "Low" (pull-up resistor built in) Active "Low" (no pull-up resistor built in) Output Voltage: e.g. 20 2.0V, 30 3.0V etc. Output Voltage: 100mV increments, 2% accuracy e.g.2=3,3=8, 4=2 3.8V, 2% Output Voltage: 50mV increments, 2% accuracy e.g. 2=3,3=8, 4=A 3.85V, 2% SOT-23-5 Package SOT-89-5 Package Embossed Tape: Standard Feed Embossed Tape: Reverse Feed Lead-free Package
Please note that "B" version is the standard part while the A, C and D are semi-custom parts. P2/19 Rev. G, October 2006
ML6204
Marking Information
SOT-23-5
1represents the product name Designator P Product Name ML6204*******
(TOP VIEW)
2 represents the integer part of the output voltage Designator 1 2 3 4 5 6 Designator 0 1 2 3 4 5 6 7 8 9 Output Voltage (V) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Output voltage (V) 1.0 2.0 3.0 4.0 5.0 6.0 Designator A B C D E F G H I J Output voltage (V) 0.05 0.15 0.25 0.35 0.45 0.55 0.65 0.75 0.85 0.95
SOT-89-5
(TOP VIEW)
3represents the decimal part of the output voltage
e.g. 23=12 1.20V and 23=1C 1.25V. 4 represents the resistor version Designator A B C D Resistor Version Active "High" (pull-down resistor built in) Active "High" (no pull-down resistor built in) Active "Low" (pull-up resistor built in) Active "Low" (no pull-up resistor built in)
P3/19
Rev. G, October 2006
ML6204
Package Information
SOT-23-5
P4/19
Rev. G, October 2006
ML6204
Package Information
SOT-89-5
P5/19
Rev. G, October 2006
ML6204
Block Diagram
The diodes in the circuit above are the protective diodes.
Absolute Maximum Ratings
Parameter Input Voltage Output Current Output Voltage Power Dissipation SOT25 Operation Ambient Temperature Storage Temperature
* IOUT= the range of Pd/VIN-VOUT
Symbol VIN IOUT VOUT Pd Topr Tstg
Ratings 10 400 VSS-0.3 ~ VIN+0.3 250 -40 ~ +70 -55 ~ +80
Units V mA V mW C C
P6/19
Rev. G, October 2006
ML6204
Electrical Characteristics
ML6204A, B Series
Parameter Symbol Conditions IOUT = 30mA, 1.5V VOUT(T) 1.95V IOUT = 30mA, 2.0V VOUT(T) 6.0V 1mA IOUT 100mA IOUT = 30mA IOUT = 100mA VIN=VCE=VOUT(T)+1.0V VIN=VCE=VOUT(T)+1.0V VIN=OUT(T)+1.0V, VCE=VSS VOUT(T)+1.0V VIN 10V IOUT=30mA IOUT=30mA -40C Topr 85C IOUT=10mA 300Hz ~ 50kHz
VIN=[VOUT(T)+1.0]V+1.0Vp-pAC IOUT=50mA, f=10kHz
Min
Ta=25C Typ Max
-40C Ta 85C Units Circuit Min Typ Max V 1 1 1 1 2 2 1 -1 3 4 1 1 1 1 2 2 2
X0.97 VOUT(T) X1.03 X0.96 VOUT(T) X1.04 X0.98 VOUT(T) X1.02 X0.97 VOUT(T) X1.03 150 15 50 E-1 E-2 20 20 80 70 0.01 0.01 2 100 30 70 300 50 1.6 VIN 0.25 20 0.10 0.10 1.7 -0.15 -0.15 -0.15 280 60 VIN 0.20 25 0.15 0.15 120 100 0.10 0.20 10 2 20 20 90 80 0.05 0.05 145 120 1.00 0.30 10 150 30 80 mA mV mV mV A A %/V V Ppm/ C Vrms dB mA mA V V A A A
Output Voltage Maximum Output Current Load Regulation Dropout Voltage Supply Current (A series) Supply Current (B series) Standby Current Line Regulation Input Voltage Output Voltage Temp. Characteristics Output Noise Ripple Rejection Rate Current Limited Short-circuit Current CE "High" Voltage CE "Low" Voltage CE "High" Current (A series) CE "High" Current (B series) CE "Low" Current
Note
VOUT(E) IOUT MAX VOUT Vdif1 Vdif2 IDD Istby VOUT VIN-VOUT VIN VOUT Topr-VOUT en PSRR IIim Ishort VCEH VCEL ICEH ICEH ICEL
VIN=VOUT(T)+1.0V, VCE=VIN VIN=VOUT(T)+1.0V, VCE=VIN
VIN=VCE=VOUT(T)+1.0V VIN=VCE=VOUT(T)+1.0V VIN =VOUT(T)+1.0V, VCE=VSS
-0.10 -0.10 -0.10
(NOTE 1) Unless otherwise stated, VIN =VOUT(T) +1.0V (NOTE 2) VOUT(T)=Specified Output Voltage (NOTE 3) VOUT(E)=Effective Output Voltage (I.e. the output voltage when "VOUT(T)+1.0V" is provided at the VIN pin while maintaining a certain IOUT value) (NOTE 4) Vdif= (VIN1 (NOTE6) - VOUT1 (NOTE5)) (NOTE 5) VOUT1=A voltage equal to 98% of the Output Voltage whenever an amply stabilized IOUT (VOUT(T)+1.0V) is input. (NOTE 6) VIN1=The Input Voltage when VOUT1 appears as Input Voltage is gradually decreased. (NOTE 7) The values for -40C Topr 85C are designed values.
P7/19
Rev. G, October 2006
ML6204
ML6204C, D Series
Parameter Output Voltage Maximum Output Current Load Regulation Dropout Voltage Supply Current (C series) Supply Current (B series) Standby Current Line Regulation Input Voltage Output Voltage Temp. Characteristics Output Noise Ripple Rejection Rate Current Limited Short-circuit Current CE "High" Voltage CE "Low" Voltage CE "High" Current CE "Low" Current (C series) CE "Low" Current (D series)
Note (NOTE 1) Unless otherwise stated, VIN =VOUT(T) +1.0V (NOTE 2) VOUT(T)=Specified Output Voltage (NOTE 3) VOUT(E)=Effective Output Voltage (I.e. the output voltage when "VOUT(T)+1.0V" is provided at the VIN pin while maintaining a certain IOUT value) (NOTE 4) Vdif= (VIN1 (NOTE6) - VOUT1 (NOTE5)) (NOTE 5) VOUT1=A voltage equal to 98% of the Output Voltage whenever an amply stabilized IOUT (VOUT(T)+1.0V) is input. (NOTE 6) VIN1=The Input Voltage when VOUT1 appears as Input Voltage is gradually decreased. (NOTE 7) The values for -40C Topr 85C are designed values.
Symbol VOUT(E) IOUT MAX VOUT Vdif1 Vdif2 IDD Istby VOUT VIN-VOUT VIN VOUT Topr-VOUT en PSRR IIim Ishort VCEH VCEL ICEH ICEL ICEL
Conditions IOUT = 30mA, 1.5V VOUT(T) 1.95V IOUT = 30mA, 2.0V VOUT(T) 6.0V 1mA IOUT 100mA IOUT = 30mA IOUT = 100mA VIN= VOUT(T) +1.0V, VCE=VSS VIN= VOUT(T) +1.0V, VCE=VSS VIN=VCE=OUT(T)+1.0V VOUT(T)+1.0V VIN 10V IOUT=30mA IOUT=30mA -40C Topr 85C IOUT=10mA 300Hz ~ 50kHz
VIN=[VOUT(T)+1.0]V+1.0Vp-pAC IOUT=50mA, f=10kHz
Min
Ta=25C Typ Max
-40C Ta 85C Units Min Typ Max V
Circuit 1 1 1 1 2 2 1 -1 3 4 1 1 1 1 2 2 2
X0.97 VOUT(T) X1.03 X0.96 VOUT(T) X1.04 X0.98 VOUT(T) X1.02 X0.97 VOUT(T) X1.03 150 15 50 E-1 E-2 20 20 80 70 0.01 0.01 2 100 30 70 300 50 1.6 VIN 0.25 0.10 0.10 0.10 1.7 -0.15 -25 -0.15 280 60 VIN 0.20 0.15 0.15 0.15 120 100 0.10 0.20 10 2 20 20 90 80 0.05 0.05 145 120 1.00 0.30 10 150 30 80 mA mV mV mV A A %/V V Ppm/ C Vrms dB mA mA V V A A A
VIN=VOUT(T)+1.0V, VCE=VSS VIN=VOUT(T)+1.0V, VCE=VSS
VIN=VCE=VOUT(T)+1.0V VIN =VOUT(T)+1.0V, VCE=VSS VIN =VOUT(T)+1.0V, VCE=VSS
-0.10 -20 -0.10
P8/19
Rev. G, October 2006
ML6204
Dropout Voltage - Table 1
SYMBOL
PARAMETER OUTPUT VOLTAGE
E-0
E-1 Dropout Voltage 1 (mV)
E-2 Dropout Voltage 2 (mV) (IOUT=100mA) Ta=25C Vdif2 TYP 600 600 500 500 400 400 350 350 320 320 270 270 250 250 250 250 240 240 240 240 230 230 230 230 230 230 220 220 220 220 220 220 200 200 200 Vdif2 MAX 800 800 680 680 620 620 480 480 460 460 420 420 400 400 400 400 380 380 380 380 350 350 350 350 350 350 330 330 330 330 300 300 280 280 280 -40C Topr 85C Vdif2 TYP 620 620 520 520 420 420 360 360 340 340 290 290 280 280 280 280 280 280 280 280 260 260 260 260 260 260 260 260 260 260 260 260 240 240 240 Vdif2 MAX 820 820 700 700 640 640 500 500 480 480 440 440 410 410 410 410 400 400 400 400 380 380 380 380 380 380 370 370 370 370 350 350 330 330 330
Output Voltage (V)
(IOUT=30mA) Ta=25C -40C Topr 85C Vdif1 TYP 410 410 310 310 260 260 210 210 150 150 110 110 110 110 110 110 110 110 110 110 100 100 100 100 100 100 100 100 100 100 90 90 90 90 90 Vdif1 MAX 520 520 400 400 330 330 260 260 190 190 160 160 160 160 160 160 160 160 160 160 130 130 130 130 130 130 130 130 130 130 110 110 110 110 110
VOUT(T) 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20
VOUT MIN 1.455 1.504 1.552 1.601 1.649 1.698 1.746 1.795 1.843 1.892 1.960 2.009 2.058 2.107 2.156 2.205 2.254 2.303 2.352 2.401 2.450 2.499 2.548 2.597 2.646 2.695 2.744 2.793 2.842 2.891 2.940 2.989 3.038 3.087 3.136 MAX 1.545 1.597 1.648 1.700 1.751 1.803 1.854 1.906 1.957 2.009 2.040 2.091 2.142 2.193 2.244 2.295 2.346 2.397 2.448 2.499 2.550 2.601 2.652 2.703 2.754 2.805 2.856 2.907 2.958 3.009 3.060 3.111 3.162 3.213 3.264
Vdif1 TYP 400 400 300 300 250 250 200 200 140 140 100 100 100 100 100 100 100 100 100 100 90 90 90 90 90 90 90 90 90 90 80 80 80 80 80
Vdif1 MAX 500 500 380 380 320 320 250 250 180 180 150 150 150 150 150 150 150 150 150 150 120 120 120 120 120 120 120 120 120 120 100 100 100 100 100
P9/19
Rev. G, October 2006
ML6204
Dropout Voltage - Table 2
SYMBOL
PARAMETER OUTPUT VOLTAGE
E-0
E-1 Dropout Voltage 1 (mV)
E-2 Dropout Voltage 2 (mV) (IOUT=100mA) Ta=25C Vdif2 TYP 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 180 180 180 180 180 180 180 180 180 180 180 180 180 180 Vdif2 MAX 280 280 280 280 280 280 280 280 280 280 280 280 280 280 280 260 260 260 260 260 260 260 260 260 260 260 260 260 260 -40C Topr 85C Vdif2 TYP 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 220 220 220 220 220 220 220 220 220 220 220 220 220 220 Vdif2 MAX 330 330 330 330 330 330 330 330 330 330 330 330 330 330 330 310 310 310 310 310 310 310 310 310 310 310 310 310 310
Output Voltage (V)
(IOUT=30mA) Ta=25C -40C Topr 85C Vdif1 TYP 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 80 80 80 80 80 80 80 80 80 80 80 80 80 80 Vdif1 MAX 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 100 100 100 100 100 100 100 100 100 100 100 100 100 100
VOUT(T) 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65
VOUT MIN 3.185 3.234 3.283 3.332 3.381 3.430 3.479 3.528 3.577 3.626 3.675 3.724 3.773 3.822 3.871 3.920 3.969 4.018 4.067 4.116 4.165 4.214 4.263 4.312 4.361 4.410 4.459 4.508 4.557 MAX 3.315 3.366 3.417 3.468 3.519 3.570 3.621 3.672 3.723 3.774 3.825 3.876 3.927 3.978 4.029 4.080 4.131 4.182 4.233 4.284 4.335 4.386 4.437 4.488 4.539 4.590 4.641 4.692 4.743
Vdif1 TYP 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 70 70 70 70 70 70 70 70 70 70 70 70 70 70
Vdif1 MAX 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 90 90 90 90 90 90 90 90 90 90 90 90 90 90
P10/19
Rev. G, October 2006
ML6204
Dropout Voltage - Table 3
SYMBOL
PARAMETER OUTPUT VOLTAGE
E-0
E-1 Dropout Voltage 1 (mV)
E-2 Dropout Voltage 2 (mV) (IOUT=100mA) Ta=25C Vdif2 TYP 180 180 180 180 180 180 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 160 Vdif2 MAX 260 260 260 260 260 260 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 240 -40C Topr 85C Vdif2 TYP 220 220 220 220 220 220 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 Vdif2 MAX 310 310 310 310 310 310 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290 290
Output Voltage (V)
(IOUT=30mA) Ta=25C -40C Topr 85C Vdif1 TYP 80 80 80 80 80 80 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 Vdif1 MAX 100 100 100 100 100 100 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
VOUT(T) 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40 5.45 5.50 5.55 5.60 5.65 5.70 5.75 5.80 5.85 5.90 5.95 6.00
VOUT MIN 4.606 4.655 4.704 4.753 4.802 4.851 4.900 4.949 4.998 5.047 5.096 5.145 5.194 5.243 5.292 5.341 5.390 5.439 5.488 5.537 5.586 5.635 5.684 5.733 5.782 5.831 5.880 MAX 4.794 4.845 4.896 4.947 4.998 5.049 5.100 5.151 5.202 5.253 5.304 5.355 5.406 5.457 5.508 5.559 5.610 5.661 5.712 5.763 5.814 5.865 5.916 5.967 6.018 6.069 6.120
Vdif1 TYP 70 70 70 70 70 70 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50
Vdif1 MAX 90 90 90 90 90 90 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80
P11/19
Rev. G, October 2006
ML6204
Typical Performance Characteristics
(1) Output Voltage VS Output Current
(2) Output Voltage VS Input Voltage
10 mA
30 mA
100 mA
P12/19
Rev. G, October 2006
ML6204
10mA
30mA 100mA
10mA 30 mA 100mA
P13/19
Rev. G, October 2006
ML6204
(3) Supply Current VS Input Voltage
P14/19
Rev. G, October 2006
ML6204
(4) Input Transient Responses
P15/19
Rev. G, October 2006
ML6204
(5)
Load Transient Response (1)
]
P16/19
Rev. G, October 2006
ML6204
(5) Load Transient Response (2)
P17/19
Rev. G, October 2006
ML6204
(6) Turn on Response Time
P18/19
Rev. G, October 2006
ML6204
(7) Enable Response Time
DISCLAIMER: The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use.
: Vout (V)
P19/19
Rev. G, October 2006

▲Up To Search▲

Price & Availability of ML6204

	To Download ML6204 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .