|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PD-94968 IRF1404PBF Advanced Process Technology l Ultra Low On-Resistance l Dynamic dv/dt Rating l 175C Operating Temperature l Fast Switching l Fully Avalanche Rated l Automotive Qualified (Q101) l Lead-Free Description l HEXFET(R) Power MOSFET D VDSS = 40V RDS(on) = 0.004 G S ID = 202A Seventh Generation HEXFET(R) Power MOSFETs from International Rectifier utilize advanced processing techniques to achieve extremely low on-resistance per silicon area. This benefit, combined with the fast switching speed and ruggedized device design that HEXFET power MOSFETs are well known for, provides the designer with an extremely efficient and reliable device for use in a wide variety of applications including automotive. The TO-220 package is universally preferred for all automotive-commercial-industrial applications at power dissipation levels to approximately 50 watts. The low thermal resistance and low package cost of the TO-220 contribute to its wide acceptance throughout the industry. TO-220AB Absolute Maximum Ratings ID @ TC = 25C ID @ TC = 100C IDM PD @TC = 25C VGS EAS IAR EAR dv/dt TJ TSTG Parameter Continuous Drain Current, VGS @ 10V Continuous Drain Current, VGS @ 10V Pulsed Drain Current Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy Avalanche Current Repetitive Avalanche Energy Peak Diode Recovery dv/dt Operating Junction and Storage Temperature Range Soldering Temperature, for 10 seconds Mounting Torque, 6-32 or M3 screw Max. 202 143 808 333 2.2 20 620 See Fig.12a, 12b, 15, 16 1.5 -55 to + 175 -55 to + 175 300 (1.6mm from case ) 10 lbf*in (1.1N*m) Units A W W/C V mJ A mJ V/ns C Thermal Resistance Parameter RJC RCS RJA Junction-to-Case Case-to-Sink, Flat, Greased Surface Junction-to-Ambient Typ. --- 0.50 --- Max. 0.45 --- 62 Units C/W www.irf.com 1 02/02/04 IRF1404PBF Electrical Characteristics @ TJ = 25C (unless otherwise specified) V(BR)DSS V(BR)DSS/TJ RDS(on) VGS(th) gfs IDSS IGSS Qg Qgs Qgd td(on) tr td(off) tf LD LS Ciss Coss Crss Coss Coss Coss eff. Parameter Drain-to-Source Breakdown Voltage Breakdown Voltage Temp. Coefficient Static Drain-to-Source On-Resistance Gate Threshold Voltage Forward Transconductance Drain-to-Source Leakage Current Gate-to-Source Forward Leakage Gate-to-Source Reverse Leakage Total Gate Charge Gate-to-Source Charge Gate-to-Drain ("Miller") Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Internal Drain Inductance Internal Source Inductance Input Capacitance Output Capacitance Reverse Transfer Capacitance Output Capacitance Output Capacitance Effective Output Capacitance Min. 40 --- --- 2.0 76 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- Typ. Max. Units Conditions --- --- V VGS = 0V, ID = 250A 0.039 --- V/C Reference to 25C, ID = 1mA 0.0035 0.004 VGS = 10V, ID = 121A --- 4.0 V VDS = 10V, ID = 250A --- --- S VDS = 25V, ID = 121A --- 20 VDS = 40V, VGS = 0V A --- 250 VDS = 32V, VGS = 0V, TJ = 150C --- 200 VGS = 20V nA --- -200 VGS = -20V 131 196 ID = 121A 36 --- nC VDS = 32V 37 56 VGS = 10V 17 --- VDD = 20V 190 --- ID = 121A ns 46 --- RG = 2.5 33 --- RD = 0.2 D Between lead, 4.5 --- 6mm (0.25in.) nH G from package 7.5 --- and center of die contact S 5669 --- VGS = 0V 1659 --- pF VDS = 25V 223 --- = 1.0MHz, See Fig. 5 6205 --- VGS = 0V, VDS = 1.0V, = 1.0MHz 1467 --- VGS = 0V, VDS = 32V, = 1.0MHz 2249 --- VGS = 0V, VDS = 0V to 32V Source-Drain Ratings and Characteristics IS ISM VSD trr Qrr ton Notes: Parameter Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode) Diode Forward Voltage Reverse Recovery Time Reverse RecoveryCharge Forward Turn-On Time Min. Typ. Max. Units Conditions D MOSFET symbol --- --- 202 showing the A G integral reverse --- --- 808 S p-n junction diode. --- --- 1.5 V TJ = 25C, IS = 121A, VGS = 0V --- 78 117 ns TJ = 25C, IF = 121A --- 163 245 nC di/dt = 100A/s Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD) Repetitive rating; pulse width limited by Starting TJ = 25C, L = 85H max. junction temperature. (See fig. 11) Pulse width 400s; duty cycle 2%. Coss eff. is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 to 80% VDSS Calculated continuous current based on maximum allowable junction temperature. Package limitation current is 75A. RG = 25, IAS = 121A. (See Figure 12) ISD 121A, di/dt 130A/s, VDD V(BR)DSS, TJ 175C 2 www.irf.com IRF1404PBF 1000 I D , Drain-to-Source Current (A) 100 I D , Drain-to-Source Current (A) VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V TOP 1000 100 VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM4.5V TOP 4.5V 10 4.5V 10 1 0.1 20s PULSE WIDTH TJ = 25 C 1 10 100 1 0.1 20s PULSE WIDTH TJ = 175 C 1 10 100 VDS , Drain-to-Source Voltage (V) VDS , Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics TJ = 25 C TJ = 175 C RDS(on) , Drain-to-Source On Resistance (Normalized) 1000 2.5 ID = 202A I D , Drain-to-Source Current (A) 2.0 1.5 100 1.0 0.5 10 V DS= 25V 20s PULSE WIDTH 4 5 6 7 8 9 10 11 12 0.0 -60 -40 -20 0 VGS = 10V 20 40 60 80 100 120 140 160 180 VGS , Gate-to-Source Voltage (V) TJ , Junction Temperature ( C) Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance Vs. Temperature www.irf.com 3 IRF1404PBF 10000 8000 C, Capacitance(pF) Crss = C gd Coss = C + Cgd ds VGS , Gate-to-Source Voltage (V) VGS = 0V, f = 1 MHZ Ciss = C + Cgd, Cds SHORTED gs 20 ID = 121A V DS= 32V V DS= 20V 16 6000 Ciss 12 4000 Coss 8 2000 Crss 0 1 10 100 4 0 FOR TEST CIRCUIT SEE FIGURE 13 0 50 100 150 200 VDS, Drain-to-Source Voltage (V) QG , Total Gate Charge (nC) Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage 1000 10000 ISD , Reverse Drain Current (A) TJ = 175 C OPERATION IN THIS AREA LIMITED BY RDS(on) ID , Drain Current (A) 100 1000 10us 10 100 100us 1ms TJ = 25 C 1 10 10ms 0.1 0.0 V GS = 0 V 0.5 1.0 1.5 2.0 2.5 3.0 3.5 1 TC = 25 C TJ = 175 C Single Pulse 1 10 100 VSD ,Source-to-Drain Voltage (V) VDS , Drain-to-Source Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage Fig 8. Maximum Safe Operating Area 4 www.irf.com IRF1404PBF 220 200 180 LIMITED BY PACKAGE VGS RG 10V VDS RD D.U.T. + ID , Drain Current (A) 160 140 120 100 80 60 40 20 0 25 50 75 100 125 150 175 -V DD Pulse Width 1 s Duty Factor 0.1 % Fig 10a. Switching Time Test Circuit VDS 90% TC , Case Temperature ( C) Fig 9. Maximum Drain Current Vs. Case Temperature 10% VGS td(on) tr t d(off) tf Fig 10b. Switching Time Waveforms 1 Thermal Response (Z thJC ) D = 0.50 0.1 0.20 0.10 0.05 0.02 0.01 SINGLE PULSE (THERMAL RESPONSE) PDM t1 t2 Notes: 1. Duty factor D = t 1 / t 2 2. Peak TJ = P DM x Z thJC + TC 0.0001 0.001 0.01 0.1 0.01 0.001 0.00001 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRF1404PBF 15V EAS , Single Pulse Avalanche Energy (mJ) 1500 VDS L DRIVER 1200 ID 49A 101A BOTTOM 121A TOP RG 20V D.U.T IAS tp + V - DD 900 A 0.01 600 Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp 300 0 25 Starting TJ , Junction Temperature ( C) 50 75 100 125 150 175 I AS Fig 12b. Unclamped Inductive Waveforms QG Fig 12c. Maximum Avalanche Energy Vs. Drain Current 10 V QGS QGD -VGS(th) Gate threshold Voltage (V) 4.0 VG 3.0 Charge ID = -250A Fig 13a. Basic Gate Charge Waveform Current Regulator Same Type as D.U.T. 2.0 50K 12V .2F .3F D.U.T. VGS 3mA + V - DS 1.0 -75 -50 -25 0 25 50 75 100 125 150 T J , Temperature ( C ) IG ID Current Sampling Resistors Fig 14. Threshold Voltage Vs. Temperature Fig 13b. Gate Charge Test Circuit 6 www.irf.com IRF1404PBF 1000 Duty Cycle = Single Pulse Avalanche Current (A) 0.01 100 0.05 0.10 10 Allowed avalanche Current vs avalanche pulsewidth, tav assuming Tj = 25C due to avalanche losses 1 1.0E-08 1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01 tav (sec) Fig 15. Typical Avalanche Current Vs.Pulsewidth 400 350 EAR , Avalanche Energy (mJ) 300 250 200 150 100 50 0 25 50 TOP Single Pulse BOTTOM 10% Duty Cycle ID = 121A 75 100 125 150 Starting T J , Junction Temperature (C) Notes on Repetitive Avalanche Curves , Figures 15, 16: (For further info, see AN-1005 at www.irf.com) 1. Avalanche failures assumption: Purely a thermal phenomenon and failure occurs at a temperature far in excess of Tjmax. This is validated for every part type. 2. Safe operation in Avalanche is allowed as long asTjmax is not exceeded. 3. Equation below based on circuit and waveforms shown in Figures 12a, 12b. 4. PD (ave) = Average power dissipation per single avalanche pulse. 5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. Iav = Allowable avalanche current. 7. T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as 25C in Figure 15, 16). tav = Average time in avalanche. 175 D = Duty cycle in avalanche = t av *f ZthJC(D, tav) = Transient thermal resistance, see figure 11) PD (ave) = 1/2 ( 1.3*BV*Iav) = DT/ ZthJC Iav = 2DT/ [1.3*BV*Zth] EAS (AR) = PD (ave)*tav Fig 16. Maximum Avalanche Energy Vs. Temperature www.irf.com 7 IRF1404PBF Peak Diode Recovery dv/dt Test Circuit D.U.T + + Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer - + RG * * * * dv/dt controlled by RG Driver same type as D.U.T. ISD controlled by Duty Factor "D" D.U.T. - Device Under Test + VDD Driver Gate Drive P.W. Period D= P.W. Period VGS=10V * D.U.T. ISD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt VDD Re-Applied Voltage Inductor Curent Body Diode Forward Drop Ripple 5% ISD * VGS = 5V for Logic Level Devices Fig 17. For N-channel HEXFET(R) Power MOSFETs 8 www.irf.com IRF1404PBF TO-220AB Package Outline 2.87 (.113) 2.62 (.103) 10.54 (.415) 10.29 (.405) 3.78 (.149) 3.54 (.139) -A6.47 (.255) 6.10 (.240) Dimensions are shown in millimeters (inches) -B4.69 (.185) 4.20 (.165) 1.32 (.052) 1.22 (.048) 4 15.24 (.600) 14.84 (.584) 1.15 (.045) MIN 1 2 3 LEAD ASSIGNMENTS IGBTs, CoPACK 1 - GATE 21- GATE DRAIN 1- GATE 32- DRAINSOURCE 2- COLLECTOR 3- SOURCE 3- EMITTER 4 - DRAIN LEAD ASSIGNMENTS HEXFET 14.09 (.555) 13.47 (.530) 4- DRAIN 4.06 (.160) 3.55 (.140) 4- COLLECTOR 3X 3X 1.40 (.055) 1.15 (.045) 0.93 (.037) 0.69 (.027) M BAM 3X 0.55 (.022) 0.46 (.018) 0.36 (.014) 2.54 (.100) 2X NOTES: 1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION : INCH 2.92 (.115) 2.64 (.104) 3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB. 4 HEATSINK & LEAD MEASUREMENTS DO NOT INCLUDE BURRS. TO-220AB Part Marking Information E XAMPL E : T HIS IS AN IR F 1010 LOT CODE 1789 AS S E MB L E D ON WW 19, 1997 IN T H E AS S E MB LY L INE "C" INT E R NAT IONAL R E CT IF IE R L OGO AS S E MB L Y LOT CODE PAR T NU MB E R Note: "P" in assembly line position indicates "Lead-Free" DAT E CODE YE AR 7 = 1997 WE E K 19 L INE C TO-220AB package is not recommended for Surface Mount Application. Data and specifications subject to change without notice. This product has been designed and qualified for the automotive [Q101] market. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information.02/04 www.irf.com 9 Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/ |
Price & Availability of IRF1404PBF |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |