|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HG Genuine GBIC Transceiver MGB-243S GBIC Transceiver MGB-243S Features Operating temperature range 0C to +70C Operating bit rate 1250Mbps Hot-pluggable capability. Low power dissipation 1310 nm FP laser SCA-2 electrical interface Single 3.3V/5V power supply Differential PECL input and output TTL signal detect indicator Duplex SC optical interface Detailed product information in E2PROM Applications Gigabit Ethernet Switch to Switch interface Router/server interface Other optical transmission systems Description: MGB-243S is compliant with Gigabit Interface Converter (GBIC) specification Rev5.5. It meets the requirements of IEEE 802.3 Gigabit Ethernet standard and ANSI specifications for fiber channel. It can be inserted in or removed from host chassis without shutting power of the host system. MGB-243S Operating Wavelength is 1310nm, it enables cost-effective data transmission over optical fibers at a distance of 10 km. The operating voltage is +3.3V or +5V. Specifications: Absolute Maximum Ratings Parameter Supply Voltage Ambient Operating Temperature Storage Temperature Relative Humidity Data Input Voltage Transmitter Differential Input Voltage Operating Current Symbol VCC TC Tstg RH TX-DAT TX-DAT Iop -- Min -0.5 0 -40 5 -0 .5 Typ Max 6 70 85 95 VDDT 2000 300 Unit V C C % V mVp-p mA 1of7 HG Genuine Transceiver Electrical Characteristics Parameter Surge Current Power Dissipation Symbol ISURGE PDISS 0.5 0.8 Min Typ Max 30 1.0 1.5 Unit mA W W GBIC Transceiver MGB-243S Note 3.3V 5V Transmitter Electro-optical Characteristics Parameter Output Optical Power 9/125um SMF Optical Extinction Ratio Center Wavelength Spectral Width Optical Rise /Fall Time Total Contributed Jitter Max. Pout TX-DISABLE Asserted Output Eye Differential Input Voltage Transmit Fault Output-Low Transmit Fault Output-High TX-DISABLE Assert Time TX-DISABLE Negate Time Time to initialize, includes reset of TX-FAULT TX-FAULT from fault to assertion TX-DISABLE time to start reset Receiver Electro-optical Characteristics Parameter Input Optical Power Operating Center Wavelength Return Loss Receiver Loss of Signal-TTL low Receiver Loss of Signal-TTL high Receiver Differential Output Voltage Receiver Output Rise Time Receiver Output Fall Time Receiver Loss of Light Load Receiver Loss of Signal Output Voltage -low Receiver Loss of Signal Output Voltage -high Symbol Pin C ORL PRX-LOS A PRX-LOS D RX_DAT TrRx_DAT TfRX_DAT RX-LOSLoad Symbol PO Min -9.5 9 Typ 7 Max -3 Unit dBm avg dB nm nm rms ns ps p-p dBm V V V us ms ms us us Note C tr/tf TJ POFF VDIFF TX-FAULTL TX-FAULTH 1280 1310 1340 2.8 0.26 227 -35 Compliant with IEEE802.3z 0.65 0 2.4 2.0 0.5 VCC 10 1 300 100 10 t-off t-on t-init t-fault t-reset Min -23 1200 12 Typ 7 Max -3 1660 -23 Unit 7 Note 2 -1 PRBS BER<10-12 dBm nm dB dBm dBm mV-p -31 370 0.25 0.25 4.7 0.0 VCC-0.5 2000 0.35 0.35 10 0.5 VCC+0.3 ns ns K V V RX-LOSL RX-LOSH 2of7 HG Genuine Receiver Loss of Signal Assert Time _Logic low to high Receiver Loss of Signal Assert Time _Logic high to low tA, RX-LOS tD, RX-LOS 100 100 GBIC Transceiver MGB-243S us us Pin Figure Figure 1 Pin Definitions: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Signal Name RX-LOS RGND RGND MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) TX-DISABLE TGND TGND TX-FAULT RGND -RX_DAT +RX_DAT RGND VDDR VDDT TGND +TX_DAT -TX_DAT TGND Receiver Ground Receiver Ground TTL Low SCL Serial Clock Signal SDA Serial Data Signal Transmitter Disable Transmitter Ground Transmitter Ground Transmit Fault Receiver Ground Receiver Data, Differential PECL, AC coupled Receiver Data, Differential PECL, AC coupled Receiver Ground Receiver supply Transmitter supply Transmitter Ground Transmitter Data, Differential PECL, AC coupled Transmitter Data, Differential PECL, AC coupled Transmitter Ground Description Receiver Loss of Signal, TTL high, open collector Functions Description The laser is driven by a LD driver IC which converts differential input LVPECL (3.3V) or PECL (5V) logic signals into an analog laser driving current. MGB-243X complies with Module Definition 4. It features an EEPROM that contains the detailed product 3of7 HG Genuine GBIC Transceiver MGB-243S information stored for retrieval by host equipment. This information is accessed via the 2-wire serial CMOS EEPROM protocol of ATMEL AT24C01A. TX_Fault When sensing an improper power level in the laser driver, the GBIC set this signal high and turns off the Laser. TX_FAULT can be reset with the TX_DISABLE line. The signal is in TTL level. TX_Disable The TX_DISABLE signal is high (TTL logic "1") to turn off the laser output. The laser will turn on within 1ms when TX_DISABLE is low (TTL logic "0"). Receive Loss (RX_LOS) The RX_LOS is high (logic "1") when there is no incoming light from the companion transceiver. This signal is normally used by the system for the diagnostic purpose. The signal is operated in TTL level. Figure 2 shows the internal frame of GBIC, Figure34 show the typical eye diagrams of this product. RECEIVEER RXLOS RXdRXd+ jimper DATA+ VCC LA DATA- CONNECTOR MOD_DEF(2) MOD_DEF(1) MOD_DEF(0 ) TRANSIMITER BIAS VCC DATA+ PM TX-FAULT Figure 2: Internal Frame LD TXdTXdis LASER DRIVER TXd+ PT ID E2PROM 4of7 HG Genuine GBIC Transceiver MGB-243S Figure 3: Receiver Eye Diagram 7 Figure4: Transmitter Eye Diagram Note: measured with a 2 -1 PRBS test pattern @1.25Gbps Interface Circuit Figure 5 shows the recommended interface circuit for GBIC application. Host Board DC+5V/+3.3V 4.7K to 10K TX-DISABLE GBIC Module DC+5V/+3.3V 4.7K to 10K TX-FAULT SerDat OUT+ TX-DAT TX-DATQ DC+5V/+3.3V Z0=75 Z0=75 PECL Note A 2X180 SerDat OUT- Laser driver DC+5V/+3.3V serDat IN- Z0=75 Z0=75 RX-DATQ RX-DAT PECL DC+5V/+3.3V 4.7K to 10K serDat IN+ Amplifier RX-LOS DC+5V/+3.3V 3X4.7K to 10K MOD-DEF(2) MOD-DEF(1) MOD-DEF(0) EEPROM GNDR Figure 5: Interface Circuit 5of7 HG Genuine Figure Dimension: (Unit: mm) GBIC Transceiver MGB-243S Figure 6: Dimension Unit: mm 11 65 36 30.4 6of7 HG Genuine Ordering Information: GBIC Transceiver MGB-243S Digital Transceiver Module MGB GBIC Module X1X2 X3 X4 X5 X6 X7 Operating Level: CPECL; T:TTL Laser Type: F:F-P(omit); D:DFB ; V:VCSEL(omit) Operating Voltage: 0: 3.3V or 5V currency(omit) 55V Transmit Distance: S:short distanceM:middle distance L:long distance; U:super long distance Operating Wavelength 31310nm51550nm8850nm Operating Rate 03155Mb/s 12622Mb/s 241.25Gb/s 482.5Gb/s Statement: HG Genuine possesses the authority for ultimate explanation of the content; all information contained in this document is subject to change without notice. All information contained in this document was obtained in specific environments; the users should responsible for verifying the products performance in their own operating environments. HG Genuine is not liable for the performance of users' products. All information contained in this document is only for the users' reference and is not the verification of the product quality. Version: V2.1 Publishing Date: 2005-05-07 Contact Information: Address: Huagong Tech BDG, Science &Technology Region of Hust, Donghu High-Tech Zone, Wuhan Hubei, P.R.China Post Code: 430223 Tel: +86-27-87180203 Website: http://www.genuine-opto.com 7of7 |
Price & Availability of MGB-033S0DC |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |