View XP1043-QH-EV1_4142837.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

12.0-16.0 GHz Power Amplifier QFN, 4x4mm
February 2008 - Rev 06-Feb-08
P1043-QH
Features
32 dBm Saturated RF Power 41 dBm Output IP3 Linearity 17 dB Gain Control On-Chip Power Detector 4x4mm Standard QFN Package 100% RF Testing
General Description
The XP1043-QH is a packaged linear power amplifier that operates over the 12.0-16.0 GHz frequency band. The device provides 20 dB gain and 41 dBm Output Third Order Intercept Point (OIP3) across the band and is offered in an industry standard, fully molded 4x4mm QFN package. The packaged amplifier is comprised of a three stage power amplifier with an integrated, temperature compensated on-chip power detector. The device includes on-chip ESD protection structures and DC by-pass capacitors to ease the implementation and volume assembly of the packaged part. The device is manufactured in 0.5um GaAs PHEMT device technology with BCB wafer coating to enhance ruggedness and repeatability of performance. XP1043-QH is well suited for Point-to-Point Radio, LMDS, SATCOM and VSAT applications.
Absolute Maximum Ratings1
Supply Voltage (Vd1,2,3) Supply Current (Id1,2,3) Gate Bias Voltage (Vg1,2,3) Max Power Dissipation (Pdiss) RF Input Power Operating Temperature (Ta) Storage Temperature (Tstg) Channel Temperature (Tch)
+10.0V 1500 mA -3V 8.0W +19 dBm -55 to +85 C -65 to +150 C -40 to MTTF Graph2
(1) Operation of this device above any one of these parameters may cause permanent damage. (2) Channel temperature directly affects a device's MTTF. Channel temperature should be kept as low as possible to maximize lifetime.
Electrical Characteristics (Ambient Temperature T = 25 oC)
Parameter Frequency Range (f ) Small Signal Gain (S21) Input Return Loss (S11) Output Return Loss (S22) Reverse Isolation (S12) P1dB Psat OIP3 Drain Bias Voltage (Vd1,2,3) Detector Bias Voltage (Vdet,ref ) Gate Bias Voltage (Vg1,2,3) Supply Current (Id1) Supply Current (Id2) Supply Current (Id3) Units GHz dB dB dB dB dBm dBm dBm VDC VDC VDC mA mA mA Min. 12.0 Typ. 20.0 15.0 10.0 55.0 30.0 32.0 41.0 7.0 5.0 -1.0 100 200 400 Max. 16.0
-2
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 1 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier QFN, 4x4mm
February 2008 - Rev 06-Feb-08
P1043-QH
Power Amplifier Measurements
XP1043-QH: S-Parameters at Room Temp. Vd=7 V, Id1=60 mA, Id2=120 mA, Id3=240 mA
24 20 16
XP1043-QH: Pout (dBm) vs Pin (dBm) at Room Temp. Vd = 7 V, Iq = 700mA
34 32 30 Output Power (dBm) 28 26 24 22 20 18 16 14 12
Pout, Freq = 12.5 GHz Pout, Freq = 13.0 GHz Pout, Freq = 13.5 GHz Pout, Freq = 14.0 GHz Pout, Freq = 14.5 GHz Pout, Freq = 15.0 GHz Pout, Freq = 15.5 GHz
S21
S-Parameters (dB)
12 8 4 0 -4 -8 -12 -16 -20 -24 11 11.5 12 12.5 13 13.5 14 14.5 15 15.5 16 16.5 17
S22 S11
Frequency (GHz)
10 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 20 22 Input Power (dBm)
XP1043-QH: Pout (dBm) vs Pin (dBm) at +85 C. Vd = 7 V, Iq = 700mA
34 30 Output Power (dBm) 28 26 24 22 20 18 16 14 12 10 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 20 22 Input Power (dBm)
Pout, Freq = 12.5 GHz Pout, Freq = 13.0 GHz Pout, Freq = 13.5 GHz Pout, Freq = 14.0 GHz Pout, Freq = 14.5 GHz Pout, Freq = 15.0 GHz Pout, Freq = 15.5 GHz
XP1043-QH: V_Detect vs Output Power, 12-16 GHz T=25C (green and +80C ( ed) ) r
10000 Detector Voltage = Vref - Vdet (mV)
32
1000
100
10
1 -5 0 5 10 15 20 25 30 35 Output Power (dBm)
XP1043-QH: C/I3 (dBc) vs Pout per Tone (dBm) at Room Temp. Vd=7 V, Id=700 mA. 12.5 to 15.5 GHz
60 55 50 45 40 65 60 55 50 45 40 35 30 25 20 15 10 5 0 14 15 16 17 18 19 20 21 22 14
XP1043-QH: C/I3 (dBc) vs Pout per Tone (dBm) at at +85 C. Vd=7 V, Id=700 mA. 12.5 to 15.5 GHz
CI/3 (dBc)
35 30 25 20 15 10 5 0
CI3, Freq = 12.5 GHz, Temp = 35 C CI3, Freq = 13.5 GHz, Temp = 35 C CI3, Freq = 14.5 GHz, Temp = 35 C CI3, Freq = 15.5 GHz, Temp = 35 C
CI/3 (dBc)
CI3, Freq = 12.5 GHz, Temp = 85 C CI3, Freq = 13.5 GHz, Temp = 85 C CI3, Freq = 14.5 GHz, Temp = 85 C CI3, Freq = 15.5 GHz, Temp = 85 c
15
16
17
18
19
20
21
22
Output Power (dBm per tone)
Output Power (dBm per tone)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 2 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier QFN, 4x4mm
February 2008 - Rev 06-Feb-08
P1043-QH
Package Dimensions / Layout
Functional Schematic
GND GND
24 23
GND VD1
22 21
VD2
20
VD3
Pin Designations
18 17 16 15 14 13 GND GND GND RF OUT GND GND
19
GND GND GND RF IN GND GND
1 2 3 4 5 6
10
11
VG1 VG2 VG3
GND Vdet
Vref
12
7
8
9
Pin Number Pin Name Pin Function 1-3 GND Ground 4 RF In RF Input 5-6 GND Ground 7 VG1 Gate 1 Bias 8 VG2 Gate 2 Bias 9 VG3 Gate 3 Bias 10 GND Ground 11 Vdet Pwr Det 12 Vref Pwr Det Reference 13-14 GND Ground 15 RF Out RF Output 16-18 GND Ground 19 VD3 Drain 3 Bias 20 VD2 Drain 2 Bias 21 VD1 Drain 1 Bias 22-24 GND Ground
Nominal Value
~ -1.0V ~ -1.0V ~ -1.0V 5.0V 5.0V
7.0V, 400 mA 7.0V, 200 mA 7.0V, 100 mA
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 3 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier QFN, 4x4mm
February 2008 - Rev 06-Feb-08
P1043-QH
App Note [1] Biasing - As shown in the Pin Designations table, the device is operated by biasing VD1,2,3 at 7.0V with 100, 200, 400mA respectively. It is recommended to use active bias to keep the currents constant in order to maintain the best performance over temperature. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -1.0V. Make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Board Layout - As shown in the board layout, it is recommended to provide 100pF decoupling caps as close to the bias pins as possible, with additional 10F decoupling caps.
Recommended Layout
Recommended Decoupling Capacitors: 100pF 0402, 10F 0805
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 4 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier QFN, 4x4mm
February 2008 - Rev 06-Feb-08
P1043-QH
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: * Do not ingest. * Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. * Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Electrostatic Sensitive Device Observe all necessary precautions when handling. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Typical Reflow Profiles Reflow Profile Ramp Up Rate Activation Time and Temperature Time Above Melting Point Max Peak Temperature Time Within 5 C of Peak Ramp Down Rate SnPb 3-4 C/sec 60-120 sec @ 140-160 C 60-150 sec 240 C 10-20 sec 4-6 C/sec Pb Free 3-4 C/sec 60-180 sec @ 170-200 C 60-150 sec 265 C 10-20 sec 4-6 C/sec
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260C reflow) "Pb Free" processes.
Ordering Information
Part Number for Ordering XP1043-QH-0G00 XP1043-QH-0G0T XP1043-QH-EV1 Description Matte Tin plated RoHS compliant 4x4 24L QFN surface mount package in bulk quantity Matte Tin plated RoHS compliant 4x4 24L QFN surface mount package in tape and reel XP1043-QH evaluation board
Caution: ESD Sensitive
Appropriate precautions in handling, packaging and testing devices must be observed.
Proper ESD procedures should be followed when handling this device.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.

▲Up To Search▲

Price & Availability of XP1043-QH-EV1

	To Download XP1043-QH-EV1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .