View HT17E11-300_4127426.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF HYDIS A N D S H A L L N O T B E REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF HEI AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST.
TITLE: HT17E11-300 Preliminary Product Specification
Rev. P1
Hyundai Display Technology, Inc.
SPEC. NUMBER S864-1080 RASR 055-2
PRODUCT GROUP TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
PAGE 1 OF 22 A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
REVISION HISTORY
REV.
P0 P1
ECN NO.
-
DESCRIPTION OF CHANGES
Initial Release Up-date optical specifications (page 7)
DATE DEC. 14, `01
JAN. 09, `02
PREPARED
K.C.CHO K.C.CHO
SPEC. NUMBER S864-1080 RASR 056-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 2 OF 22 A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
Contents
No. 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connection Signal Timing Specifications Signal Timing Waveforms of interface signal (DE mode) Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling & Cautions Appendix Item Page 4 5 6 7 9 11 13 14 15 16 17 18 19
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 3
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
1.0 GENERAL DESCRIPTION
REV. P1
ISSUE DATE
JAN. 09, `02
1.1 Introduction
[HT17E11-300] is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 17.0 inch diagonally measured active area with SXGA resolutions (1280 horizontal by 1024 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16,194,227 colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.
CN21 CN22
LVDS Input Signal
Connector (CN11)
Source Driver LVDS Rx + Timing Controller
TFT LCD Panel 1280 1024
Gate Driver
VDD
Power & Analog Block
CN23 CN24
1.2 Features l LVDS Interface with 2 pixel / clock l High-speed response l Low power consumption l 8-bit color depth, display 16,194,227 colors l Incorporated edge type back-light (Four lamps) l High luminance and contrast ratio, low reflection and wide viewing angle l DE (Data Enable) mode only 1.3 Applications l Desktop Type of PC & Workstation Use l Slim-Size Display for Stand-alone Monitor l Display Terminals for Control System l Monitors for Process Controller
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 4
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
1.4 General Specifications The followings are general specifications at the model [HT17E11-300]. Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Back-light Specification 337.92 (H) 270.336(V) 1280(H) 1024(V) 0.264(H) 0.264(V) RGB Vertical stripe 16,194,227 Normally White 383.5(H) 306.0(V) 21.0(D) typ. 2,200 typ. Top/Bottom edge side 4-CCFL type
REV. P1
ISSUE DATE
JAN. 09, `02
Unit mm pixels mm
Remarks
colors
mm gram Note 1
Note: 1. CCFL (Cold Cathode Fluorescent Lamp) 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2.

Parameter Power Input Voltage Logic Input Voltage Back-light Lamp Current Back-light lamp Frequency Operating Temperature (Humidity) Storage Temperature (Humidity) Symbol VDD VIN IBL FL TOP RH TST RH -20 Min VSS-0.5 VSS-0.3 3 40 0 Max 6.5 VDD+0.3 7 (80) +50 80 +60 90 [VSS = GND =0V] Unit V V mA KHz E % E % A 40 E A 40 E Remarks Ta = 25E
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 5
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
3.0 ELECTRICAL SPECIFICATIONS < Table 3. Electrical specifications > Parameter Power Supply Voltage Power Supply Current Permissible Input Ripple Voltage High Level Differential Input Threshold Voltage Low Level Differential Input Threshold Voltage Back-light Lamp Voltage Back-light Lamp Current Back-light Lamp operating Frequency Lamp Start Voltage 1310 Lamp Life PD Power Consumption P BL P total 40000 50000 2.8 17.0 19.8 VDD IDD VRF VIH VIL VBL IBL FL -100 680 3.0 40 710 6.0 840 7.0 60 1075 Min 4.5 Typ 5.0 560 Max 5.5 1000 100 +100
REV. P1
ISSUE DATE
JAN. 09, `02
[Ta = 253/42E] Unit V mA mV mV mV Vrms mArms KHz Vrms Vrms hrs W W W IBL = 6.0mA, Note 4 Note 2 25E, Note 3 0E , Note 3 IBL = 6.0mA Remarks Note1 VDD = 5.0V Vcm = 1.2V typ.
Notes: 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD = 5.0V, Frame rate= 60Hz and Clock frequency = 54MHz. Test Pattern of power supply current a) Typ: Vertical color bar pattern b) Max: Vertical 2 Skip lines pattern 2. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 3. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the lamps may not be turned on. 4. Calculated value for reference (VBL IBL) 4 excluding inverter loss.
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 6
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
4.0 OPTICAL SPECIFICATIONS
REV. P1
ISSUE DATE
JAN. 09, `02
4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 252C) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. We refer to =0 (=3) as the 3 o'clock direction (the "right"), =90 (=12) as the 12 o'clock direction ("upward"), =180 (=9) as the 9 o'clock direction ("left") and =270 (=6) as the 6 o'clock direction ("bottom"). While scanning and/or , the center of the measuring spot on the display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/- 10% at 25C. Optimum viewing angle direction is 6 o'clock. 4.2 Optical Specifications [VDD=5.0V, Frame rate=60Hz, Clock=54MHz, IBL = 6.0mA, Ta = 253/42E] Parameter Horizontal Viewing Angle Vertical Luminance contrast ratio Luminance of white White luminance uniformity White Red Reproduction of color Green Blue Response time (Rise + Decay) Cross talk Symbol E3 E9 E12 E6 CR YW AY xW yW xR yR xG yG xB yB Ttotal CT E = 0 (Center) Normal Viewing Angle CR > 10 Condition Min 65 65 40 60 350 0.291 0.308 0.610 0.317 0.272 0.557 0.113 0.069 Typ 70 70 45 65 500 250 0.321 0.338 0.640 0.347 0.302 0.587 0.143 0.099 20 Max 1.2 0.351 0.368 0.670 0.377 0.332 0.617 0.173 0.129 2.0 msec % Note 6 Note 7 Note 5 cd/m2 Unit Deg Deg Deg Deg Note 2 Note 3 Note 4 Note 1 Remark
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 7
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
Note: 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o'clock direction and the vertical or 6, 12 o'clock direction with respect to the optical axis which is normal to the LCD surface (See FIGURE 1 shown in Appendix). 2. Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR = 3. Luminance when displaying a white raster Luminance when displaying a black raster
4.
5.
6.
7.
Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. The White luminance uniformity on LCD surface is then expressed as : AY = Maximum Luminance of five points / Minimum Luminance of five points (See FIGURE 2 shown in Appendix). The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the "data" input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix).
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 8
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
5.0 INTERFACE CONNECTION 5.1 Electrical Interface Connection l CN11: Module Side Connector User Side Connector
Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Symbol RXO0RXO0+ RXO1RXO1+ RXO2RXO2+ GND RXOCLKRXOCLK+ RXO3RXO3+ RXE0RXE0+ GND RXE1RXE1+ GND RXE2RXE2+ RXECLKRXECLK+ RXE3RXE3+ GND NC DE NC VDD VDD VDD POWER SUPPLY (+5.0V)
REV. P1
ISSUE DATE
JAN. 09, `02
: FI-X30S-HF (JAE) : FI-X30H-HF (JAE) or equivalent
Function Remark
LVDS ODD 0 - SIGNAL LVDS ODD 0 + SIGNAL LVDS ODD 1 - SIGNAL LVDS ODD 1 + SIGNAL LVDS ODD 2 - SIGNAL LVDS ODD 2 + SIGNAL GROUND LVDS ODD CLOCK - SIGNAL LVDS ODD CLCOK + SIGNAL LVDS ODD 3 - SIGNAL LVDS ODD 3 + SIGNAL LVDS EVEN 0 - SIGNAL LVDS EVEN 0 + SIGNAL GROUND LVDS EVEN 1 - SIGNAL LVDS EVEN 1 + SIGNAL GROUND LVDS EVEN 2 - SIGNAL LVDS EVEN 2 + SIGNAL LVDS EVEN CLOCK - SIGNAL LVDS EVEN CLOCK + SIGNAL LVDS EVEN 3 - SIGNAL LVDS EVEN 3 + SIGNAL GROUND NO CONECTION DE OUT NO CONECTION
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification 9
PAGE OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
5.2 LVDS Interface (Tx : THC63LVDM83A or Equivalent)
Input signal OR0 OR1 OR2 OR3 OR4 OR5 OG0 OG1 OG2 OG3 OG4 OG5 OB0 OB1 OB2 OB3 OB4 OB5 HSYNC VSYNC DE MCLK OR6 OR7 OG6 OG7 OB6 OB7 RSVD ER0 ER1 ER2 ER3 ER4 ER5 EG0 EG1 EG2 EG3 EG4 EG5 EB0 EB1 EB2 EB3 EB4 EB5 HSYNC VSYNC DE MCLK ER6 ER7 EG6 EG7 EB6 EB7 RSVD Transmitter Pin No Pin No 51 52 54 48 55 47 56 3 4 6 7 11 46 12 45 14 15 19 20 22 23 42 24 41 27 28 30 31 40 39 50 2 8 38 10 37 16 18 25 51 52 54 48 55 47 56 3 4 6 7 11 46 12 45 14 15 19 20 22 23 42 24 41 27 28 30 31 40 39 50 2 8 38 10 37 16 18 25 Interface System (Tx) TFT-LCD (Rx)
REV. P1
FI-X30S-HF Pin No.
ISSUE DATE
JAN. 09, `02
Remark
OUT0OUT0+
RXO0RXO0+
1 2
O D D L V D S
OUT1OUT1+
RXO1RXO1+
3 4
OUT2OUT2+
RXO2RXO 2+
5 6
CLKOUTCLKOUT+
RXO CLKRXO CLK+
8 9
OUT3+ OUT3-
RXO 3RXO 3+
10 11
OUT0OUT0+
RXE0RXE 0+
12 13
E V E N L V D S
OUT1OUT1+
RXE 1RXE 1+
15 16
OUT2OUT2+
RXE 2RXE 2+
18 19
CLKOUTCLKOUT+
RXE CLKRXE CLK+
20 21
OUT3+ OUT3-
RXE 3RXE 3+
22 23
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 10 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
5.3 Data Input Format ODD EVEN (1,1) (2,1) RGBRGB
REV. P1
ISSUE DATE
JAN. 09, `02
(1279,1) (1280,1) RGBRGB
1 Pixel = 3 Dots
RGB
RGBRGB (1,1024) (2,1024)
RGBRGB (1279,1024) (1280,1024) Display Position of Input Data (V-H)
5.4 Back-light Interface Connection l CN21, 22, 23, 24: Module side connector User side connector Pin No 1 2 INPUT HOT COLD
: BHSR-02VS-1 (JST) : SM02B-BHSS-1-TB (JST) or equivalent Color Pink White Function High voltage Ground
6.0 SIGNAL TIMING SPECIFICATIONS 6.1 The [HT17E11-300] is operated by the only DE (Data enable) mode (LVDS Transmitter Input) Item Frequency Clock High Time Low Time Setup Time Data Hold Time Data Enable Setup Time Frame Period Vertical Display Period One Line Scanning Period Horizontal Display Period Symbols 1/Tc Tch Tcl Tds Tdh Tes Tv Tvd Th Thd Min 5 5 4 4 4 1032 672 640 Typ 54 1066 1024 844 640 Max 68 2044 1022 640 Unit MHz ns ns ns ns ns lines lines clocks clocks
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 11 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
6.2 LVDS Rx interface timing parameter The specification of the LVDS Rx interface timing parameter is shown in Table 4. < Table 4. LVDS Rx Interface Timing Specification> Symbol Min Typ Max tRCIP tCdiff tRIP1 tRIP0 tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 14.7 TBD -0.2
1*tRICP/7-0.2 2*tRICP/7-0.2 3*tRICP/7-0.2 4*tRICP/7-0.2 5*tRICP/7-0.2 6*tRICP/7-0.2
Item CLKIN Period CLK Difference Input Data 0 Input Data 1 Input Data 2 Input Data 3 Input Data 4 Input Data 5 Input Data 6
Unit nsec nsec nsec nsec nsec nsec nsec nsec nsec
Remark
18.5 0 0
1*tRICP/7 2*tRICP/7 3*tRICP/7 4*tRICP/7 5*tRICP/7 6*tRICP/7
TBD +0.2
1*tRICP/7+0.2 2*tRICP/7+0.2 3*tRICP/7+0.2 4*tRICP/7+0.2 5*tRICP/7+0.2 6*tRICP/7+0.2
TRIP2 tRIP3 tRIP4 tRIP5 tRIP6 tRIP0 tRIP1 RXO/Ez +/* Z=0, 1, 2, 3
Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0
RXOCLK+
Vdiff=0[v] tRCIP
Vdiff=0[v]
RXECLK+
tCdiff
* Vdiff = (RXO/Ez+)-(RXO/Ez-), ..... , (RXO/ECLK+)-(RXO/ECLK-)
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 12 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL (DE MODE) 7.1 Vertical Timing Waveforms
Tv Tvd
MCLK Th ENAB
R7 ~ R0 G7 ~ G0 B7 ~ B0
Invalid Data
x,1
x,2
x,y
x,1024
Invalid
Data
x+1,1
7.2 Horizontal Timing Waveforms
Th Thd MCLK Tc ENAB
RA7 ~RA0 GA7 ~GA0 BA7 ~BA0
D1
D2
Dn
D638
D639
D640
Invalid
Data
D1
D2
D3
Tch
Tcl 2.0V
MCLK Tds
1.5V Tdh
0.8V
Data
Valid Tes
Data
2.0V 0.8V
ENAB
2.0V
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 13 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
Colors & Gray Scale Black Blue Green Cyan Red Magenta Yellow White Black a Darker a a Brighter a Red Black a Darker a a Brighter a Green Black a Darker a a Brighter a Blue Black a Darker a a Brighter a White Red data 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 00 00 00 00 11 11 11 11 00 00 00 e e 11 11 11 00 00 00 e e 00 00 00 00 00 00 e e 00 00 00 00 00 00 e e 11 11 11 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 Green data 0 0 1 1 0 0 1 1 0 0 0 00 00 11 11 00 00 11 11 00 00 00 e e 00 00 00 00 00 00 e e 11 11 11 00 00 00 e e 00 00 00 00 00 00 e e 11 11 11 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0
REV. P1
ISSUE DATE
JAN. 09, `02
Blue data
8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Basic Colors
Gray Scale Of Red
0 1 0 1 0 0 0 1 0 0 0
0 1 0 1 0 0 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
Gray Scale Of Green
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Gray Scale Of Blue
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Gray Scale Of White & Black
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
1 1 1
1 1 1
1 1 1
00 11 00 11 00 11 00 11 00 00 00 e e 00 00 00 00 00 00 e e 00 00 00 00 00 00 e e 11 11 11 00 00 00 e e 11 11 11
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
1 1 1 0 0 0
0 1 1 0 0 1
1 0 1 0 1 0
1 1 1
0 1 1
1 0 1
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 14 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT 9.0 POWER SEQUENCE
REV. P1
ISSUE DATE
JAN. 09, `02
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence should be as shown in below
0.9VDD
0.9VDD 0.1VDD
Power Supply
0V
0.1VDD
T1 T2 T5 T6
Interface Signal
0V
Valid
T3
T4
Back- light
0V
l l l l l l
0 < T1 5 ms 20 ms < T2 50 ms 500 ms T3 100 T4 0 < T5 50 ms 1 sec T6
Notes: 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 15 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements
REV. P1
ISSUE DATE
JAN. 09, `02
FIGURE 6 shown in appendix shows mechanical outlines for the model [HT17E11-300]. Other parameters are shown in Table 5.

Parameter Active area Number of pixels Specification 337.92 (H) 270.336(V) 1280(H) 1024(V) (1 pixel = R + G + B dot) Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Back-light 0.264(H) 0.264(V) RGB Vertical stripe 16,194,227 Normally white 383.5 (H) 306.0 (V) 21.0 (D) 2,200 typ. Top / Bottom edge side 4-CCFL type mm gram colors mm Unit mm pixels
10.2 Mounting See FIGURE 5 shown in appendix 10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50[cm] from the screen with an overhead light level of 350[lux]. The manufacture shall furnish limit samples of the panel showing the lightest leakage acceptable.
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 16 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
11.0 RELIABILITY TEST The Reliability test items and its conditions are shown in below.

No 1 2 3 operation test 4 5 6 High temperature operation test Low temperature operation test Thermal shock Vibration test 7 (non-operating) Period Gravity Shock test 8 (non-operating) Air 9 Electrostatic discharge test Contact Pulse width Gravity/AMP : 1.5G Test Items High temperature storage test Low temperature storage test High temperature & high humidity Ta = 60 C, 240 hrs Ta = -20 C, 240 hrs Ta = 50 C, 80 %RH, 240 hrs Ta = 50 C, 240 hrs Ta = 0 C, 240 hrs Conditions
REV. P1
ISSUE DATE
JAN. 09, `02
Ta = -20 C 60 C (30 min), 100 cycle Frequency : 10 ~ 300 Hz, Sweep rate 30min
: 3/4X, 3/4Y, 3/4Z 30min : 70G : 11ms, sine wave X, Y, Z Once for each direction : 150 pF, 330O, 15KV : 150 pF, 330O, 8KV
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 17 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
12.0 HANDLING & CAUTIONS
REV. P1
ISSUE DATE
JAN. 09, `02
12.1 Cautions when taking out the module Y Pick the pouch only, when taking out module from a shipping package. 12.2 Cautions for handling the module Y As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. Y As the LCD panel and back-light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. Y As the surface of the polarizer is very soft and easily scratched, use a soft dry-cloth without chemicals for cleaning. Y Do not pull the interface connector in or out while the LCD module is operating. Y Put the module display side down on a flat horizontal plane. Y Handle connectors and cables with care. 12.3 Cautions for the operation Y When the module is operating, do not lose LVDS signals. If any one of these signals were lost, the LCD panel would be damaged. Y Obey the supply voltage sequence. If the wrong sequences were applied, the module would be damaged. 12.4 Cautions for the atmosphere Y Dewdrop atmosphere should be avoided. Y Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer-packing pouch and under relatively low temperature atmosphere is recommended. 12.5 Cautions for the module characteristics Y Do not apply fixed pattern data signal to the LCD module at aging time. Y Applying fixed pattern for a long time may cause image sticking. 12.6 Other cautions Y Do not disassemble and/or re-assemble LCD module. Y Do not re-adjust variable resistor or switch etc. Y When returning the module for repair or etc, please pack the module not to be broken. We recommend on using the original shipping packages.
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 18 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
13.0 APPENDIX
REV. P1
ISSUE DATE
JAN. 09, `02
Figure 1. Measurement Set Up
Figure 2. Locations
Average Luminance Measurement Locations & Uniformity Measurement
Column
320 2
640
960 3
Row 256
1
512
4
5
768
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 19 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
Figure 3. Response Time Testing
REV. P1
ISSUE DATE
JAN. 09, `02
TFT Off(White)
TFT On(Black)
TFT Off(White)
Tr
Td
100% 90%
10% 0%
Figure 4. Cross Modulation Test Description
VIEW AREA 320, 256 320, 768
VIEW AREA 960, 256
960, 768 YB (1120, 512)
YA (1120, 512) YB - YA YA
Cross-Talk =
100
Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns.
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 20 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
Figure 5. TFT-LCD Module Outline Dimensions (Front view)
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 21 OF 22
A4 (210 X 297)
PRODUCT GROUP
TFT-LCD PRODUCT
REV. P1
ISSUE DATE
JAN. 09, `02
Figure 6. TFT-LCD Module Outline Dimensions (Rear view)
SPEC. NUMBER S864-1080 RASR 057-1
SPEC. TITLE HT17E11-300 Preliminary Product Specification
PAGE 22 OF 22
A4 (210 X 297)

▲Up To Search▲

Price & Availability of HT17E11-300

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]

Mirror Sites : [www.datasheet.hk] [www.maxim4u.com] [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com] [www.gdcy.net]

. . . . .

We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy.

	To Download HT17E11-300 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .