Part Number Hot Search : 
GSC9406 000AKCY SXXXBF 89LPC9 PDTC14 IR3839 BNP10SHG CNS020
Product Description
Full Text Search
 

To Download SC4517AIMSXXTRT Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 1.25MHz, 1.5A Step-Down Switching Regulator
POWER MANAGEMENT Description
The SC4517A is a current mode switching regulator with an integrated switch, operating at 1.25MHz with separate sync & enable functions. The integrated switch allows for cost effective low power solutions (peak switch current 1.5 amps). The sync function allows customers to synchronize to a faster clock in order to avoid frequency beating in noise sensitive applications. High frequency of operation allows for very small passive components. Current mode operation allows for fast dynamic response & instantaneous duty cycle adjustment as the input varies (ideal for CPE applications where the input is a wall plug power). The low shutdown current makes it ideal for portable applications where battery life is important. The SC4517A is a 1.25MHz switching regulator synchronizable to a faster frequency from 1.6MHz to 2MHz.
SC4517A
Features
Integrated 1.5 Amp switch 1.25MHz frequency of operation Current mode controller Synchronizable to higher frequency up to 2MHz 6A low shutdown current MSOP-8 and MLPD-8 Lead-free packages. This product is fully WEEE and RoHS compliant
Applications
XDSL modems CPE equipment DC-DC point of load applications Portable equipment
Typical Application Circuit
D1
1 VIN Enable C3 2 5 8 BST IN SW 3 6 7
C1 L1 VOUT R1
SC4517AXX
EN SYNC FB COMP
GND 4
D2 R2
C2
C4
R3
Revision: December 13, 2006
1
www.semtech.com
SC4517A
POWER MANAGEMENT Absolute Maximum Ratings
Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied. Exposure to Absolute Maximum rated conditions for extended periods of time may affect device reliability.
Parameter Input Supply Voltage
(1)
Symbol VIN (VBST - VSW) V BST V EN V FB IFB ISYNC J A TA TJ TSTG TLEAD TPKG ESD
Limits -0.3 to +24 16 -0.3 to +32 -0.3 to +16 -0.3 to +6 1 1 185 53 -40 to +85 -40 to +150 -65 to +150 300 260 2
Units V V V V V mA mA C/W C C C C C kV
Boost Pin Above VSW Boost Pin Voltage EN Pin Voltage FB Pin Voltage FB Pin Current SYNC Pin Current Thermal Impedance Junction to Ambient (2) MSOP MLPD Operating Ambient Temperature Range Operating Junction Temperature Range Storage Temperature Range Lead Temperature (Soldering) 10s (MSOP) Peak IR Reflow Temperature 10-40s (MLPD) ESD Rating (Human Body Model)
Notes: (1) For proper operation of device, VIN should be within maximum Operating Input Voltage as defined in Electrical Characteristics. (2) Minimum pad size.
Electrical Characteristics
Unless specified: VIN = 12V, VCOMP = 0.8V, VBST = VIN + 5V, EN = Tied to VIN, SYNC = 0, SW = open. TA = TJ = -40C to 125C.
Parameter Operating Input Voltage
(1)
Symbol VIN ISW fOSC VD(SW) VUVLO IQ IQ(OFF)
Conditions
Min
Typ
Max 16
Units V A
Maximum Switch Current Limit Oscillator Frequency Switch On Voltage Drop VIN Undervoltage Lockout VIN Standby Current Shutdown Current
1.5 0.9 1.25 330 2.60 VFB = VOUT(NOM) + 17% VEN = 0V, VIN = 16V, VSW = 0V 1.0 1.6 550 3 5 45
MHz mV V mA A
2006 Semtech Corp.
2
www.semtech.com
SC4517A
POWER MANAGEMENT Electrical Characteristics (Cont.)
Unless specified: VIN = 12V, VCOMP = 0.8V, VBST = VIN + 5V, EN = Tied to VIN, SYNC = 0, SW = open. TA = TJ = -40C to 125C.
PARAMETER FB Input Current Feedback Voltage
SYMBOL IFB
CONDITIONS SC4517A (adj) SC4517A (adj), SC4517A-1.8V 3V < VIN < 16V VOUT = VFB
(1)
MIN
TYP -0.25
MAX -0.50 1.227 1.836 2.55 3.366 5.1 21.0 30.0 39.0 60.0
UNITS A
1.173 1.764 2.45 3.234 4.9 10.5 14.7 19.0 29.0 150 500
1.2 1.8 2.5 3.3 5 15.0 21.0 27.5 42.0 350 850 120 110 2.5
SC4517A-2.5V SC4517A-3.3V SC4517A-5V
V
FB Input Resistance
RFB
SC4517A-1.8V SC4517A-2.5V SC4517A-3.3V SC4517A-5V
k
FB to VCOMP Voltage Gain(2) FB to VCOMP Transconductance(2) VCOMP Pin Source Current VCOMP Pin Sink Current VCOMP Pin to Switch Current Transconductance VCOMP Pin Maximum Switching Threshold VCOMP Pin Threshold Maximum Switch Duty Cycle Minimum Boost Voltage Above Switch Boost Current
0.4V VCOMP 0.9V ICOMP = 10A VFB = VOUT(NOM) - 17% VFB = VOUT(NOM) + 17%
1300 160 180
Mho A A A/V V V %
Duty cycle = 0% ISW = 1.5A VCOMP = 1.2V, ISW = 400mA ISW = 1.5A, 0C TA 125C and ISW = 1.3A, TA < 0C ISW = 0.5A ISW = 1.5A, 0C TA 125C and ISW = 1.3A, TA < 0C 80
0.35 0.9 90 1.8 10 30 2.7 15 45
V mA
2006 Semtech Corp.
3
www.semtech.com
SC4517A
POWER MANAGEMENT Electrical Characteristics (Cont.)
Unless specified: VIN = 12V, VCOMP = 0.8V, VBST = VIN + 5V, EN = Tied to VIN, SYNC = 0, SW = open. TA = TJ = -40C to 125C.
PARAMETER Enable Input Threshold Voltage
SYMBOL VIH VIL
CONDITIONS
MIN 2
TYP
MAX
UNITS V
0.4 -10 EN = 100mV below threshold 7 1.5 1.6 VSYNC = 0.5V 20 2 15
V A A V MHz k
Enable Input Bias Current
IIL IIH
SYNC Threshold Voltage SYNC Input Frequency (3) SYNC Pin Resistance
Notes: (1) The device is not guaranteed to function outside of its operating condition. The required minimum input voltage for a regulated output depends on the output voltage and load condition. (2) Guaranteed by design. (3) For SYNC applications, please contact factory.
Marking Information
Adjustable Options (MSOP) SC4517AIMS Voltage Options (MSOP) SC4517AIMSXX
APAJ yyww
AP50 yyww
yyww = Date Code (Example: 0012) xxxx = Semtech Lot No. (Example: E901 xxxx 01-1) Adjustable Options (MLPD) SC4517AIML
SC 4517 yyww
Part Number Code (Example: AP50 = 5.0V (50) yyww = Date Code (Example: 0012) xxxx = Semtech Lot No. (Example: E901 xxxx 01-1) Voltage Options (MLPD) SC4517AIMLXX
4517 XX yyww
yyww = Date Code (Example: 0012)
Part Number Code (Example: XX = 5.0V (50) yyww = Date Code (Example: 0012)
2006 Semtech Corp.
4
www.semtech.com
SC4517A
POWER MANAGEMENT Pin Configurations
TOP VIEW
BST IN SW GND 1 2 3 4 8 7 6 5 SYNC COMP FB EN
Ordering Information
Part Number (1)(2)(3) SC4517AIMSXXTRT SC4517AIMSTRT SC4517AIMLXXTRT SC4517AIMLTRT S C 4517A E V B P ackag e MSOP-8
MLPD-8 Evaluation Board
(8 Pin MSOP)
TOP VIEW
Notes: (1) Where XX denotes voltage options. Available voltages are: 1.8V (18), 2.5V (25), 3.3V (33) and 5.0V (50). Leave blank for adjustable voltage option. (2) Only available in tape and reel packaging. A reel contains 2500 for MSOP and 3000 for MLP devices. (3) Lead-free product. This product is fully WEEE and RoHS compliant.
(8 Pin MLPD)
Pin Descriptions
Pin # 1 2 Pin Name Pin Function BST IN This pin provides power to the internal NPN switch. The minimum turn on voltage for this switch is 2.7V. Pi n IN deli vers all power requi red by control and power ci rcui try. Thi s pi n sees hi gh di /dt duri ng switching actions of the switch. A decoupling capacitor should be attached to this pin as close as possible. Pin SW is the emitter of the internal switch. The external freewheeling diode should be connected as close as possible to this pin. All voltages are measured with respect to this pin. The decoupling capacitor and the freewheeling diode should be connected to GND as short as possible. This is the chip enable input. The regulator is switched on if EN is high, and it is off if EN is low. The regulator i s i n standby mode when E N i s low, and the i nput supply current i s reduced to a few microamperes. It needs to be pulled up to Vin if not used. Feedback input for adjustable output controllers. For fixed output controllers, this pin should be directly connected to the output since the voltage dividers have been integrated into the chips (SC4517AXX). Thi s i s the o utp ut o f the i nte rna l e rro r a mp li fi e r a nd i np ut o f the p e a k c urre nt c o mp a ra to r. A compensation network is connected to this pin to achieve the specified performance. This is synchronous control pin used to synchronize the internal oscillator to an external pulse control signal. When not used, it should be connected to GND.
3 4 5
SW GND EN
6
FB
7 8
COMP SYNC
THERMAL Pad for heatsinking purpose. Connect to ground plane using multiple vias. Not electrically connected PAD internally.
(MLPD only)
2006 Semtech Corp.
5
www.semtech.com
SC4517A
POWER MANAGEMENT Block Diagram
+ +
SLOPE
Is
+
ISEN
IN
40m
COMP FB
BST
-
+
EA
PWM
S R
Q
POWER TRANSISTOR
SW
Is
1V
EN
REFERENCE
UVLO
SOFT START HICCUP
0.7V SLOPE SLOPE COMP FB
OL
GND
SYNC
OSCILLATOR
FREQUENCY
CLK
2006 Semtech Corp.
6
www.semtech.com
SC4517A
POWER MANAGEMENT Application Information
General Overview The SC4517A is a high frequency current mode PWM buck regulator. It has an internal clock with fixedfrequency. The SC4517A uses two feedback loops (voltage loop and current loop) that control the duty cycle of the internal power switch. The error amplifier functions like the one of the voltage mode controller. The output of the error amplifier provides a switch current reference. This technique effectively removes one of the double poles in the output LC filter stage. With this, it is easier to compensate a current mode converter for better performance. A minimum 2.7V voltage is required to saturate the NPN power switch when it is "ON" to reduce its conduction loss. Current Limit and Overcurrent Protection The current sense amplifier in the SC4517A monitors the switch current during each cycle. Overcurrent protection (OCP) is triggered when the current limit exceeds the upper limit of 1.5A, detected by a voltage on COMP being greater than about 2V. When an OCP fault is detected, the power switch is turned off and the external COMP capacitor is quickly discharged using an internal small signal NPN transistor. Once the COMP voltage has fallen below 250mV the power switch is turned off, control circuit is held off for 50s determined by a internal timer. When the 50s time is up, an internal timer prevents any operation for 50s, the part enters a normal startup cycle. In the case of sustained overcurrent or dead-short, the part will continually cycle through the retry sequence, at a rate dependent on the value of Ccomp. During start up, the voltage on COMP rises roughly at the rate of dv/dt = 120A/Ccomp. Ccomp is the total capacitance value attached to COMP. Therefore, the retry time for a sustained overcurrent can be approximately calculated as:
Tretry = Ccomp 2V + 50us 120uA
Enable Pulling and holding the EN pin below 0.4V activates the shut down mode of the SC4517A which reduces the input supply current to less than 10A. During the shut down mode, the switch is turned off. The SC4517A is turned on if the EN pin is pulled high. Oscillator Its internal free running oscillator sets the PWM frequency at 1.25MHz for the SC4517A without any external components to program the frequency. An external clock with a duty cycle from 20% to 80% connected to the SYNC pin activates synchronous mode. The frequency of the external clock can be from 1.6MHz to 2MHz. UVLO When the EN pin is pulled and held above 1.8V, the voltage on Pin IN determines the operation of the SC4517A. As VIN increases during power up, the internal circuit senses VIN and keeps the power transistor off until VIN reaches 2.6V. Load Current The peak current IPEAK in the switch is internally limited. For a specific application, the allowed load current IOMAX will change if the input voltage drifts away from the original design as given for current continuous mode:
IOMAX = 1.5 - VO (1 - D) 2 L fs
Figure 1 shows the voltage on COMP during a sustained overcurrent condition.
2V
Where: fs = switching frequency, VO = output voltage; D = duty ratio, Vo/VI; VI = input voltage Figure 2 shows the theoretical maximum load current for the specific cases. In a real application, however, the allowed maximum load current also depends on the layout and the air cooling condition. Therefore, the maximum load current may need to be degraded according to the
7 www.semtech.com
250mV
Figure 1. Voltage on COMP for Startup and OCP
2006 Semtech Corp.
SC4517A
POWER MANAGEMENT Application Information (Cont.)
thermal situation of the application. For example, the SC4517A with EDP package is able to handle higher current than the SC4517A with MSOP package if their working conditions are same.
Maximum Load Current vs Input Voltage L=4.7uH
1.400 1.350 Iomax (A) Vo=2.5V 1.300 1.250 1.200 4 6 8 10 12 14 16 18 Vi (V) Vo=3.3V Vo=5V
Where: fs = switching frequency, = ratio of the peak to peak inductor current to the output load current and VO = output voltage. The peak to peak inductor current is:
Ip -p = * IOMAX
Ip -p 2
IPEAK = IOMAX +
After the required inductor value is selected, the proper selection of the core material is based on the peak inductor current and efficiency specifications. The core must be able to handle the peak inductor current IPEAK without saturation and produce low core loss during the high frequency operation. The power loss for the inductor includes its core loss and copper loss. If possible, the winding resistance should be minimized to reduce inductor's copper loss. The core must be able to handle the peak inductor current I PEAK without saturation and produce low core loss during the high frequency operation. The power loss for the inductor includes its core loss and copper loss. If possible, the winding resistance should be minimized to reduce inductor's copper loss. The core loss can be found in the manufacturer's datasheet. The inductor's copper loss can be estimated as follows:
PCOPPER = I2LRMS R WINDING
Figure 2. Theoretical maximum load current curves. Inductor Selection The factors for selecting the inductor include its cost, efficiency, size and EMI. For a typical SC4517A application, the inductor selection is mainly based on its value, saturation current and DC resistance. Increasing the inductor value will decrease the ripple level of the output voltage while the output transient response will be degraded. Low value inductors offer small size and fast transient responses while they cause large ripple currents, poor efficiencies and more output capacitance to filter out the large ripple currents. The inductor should be able to handle the peak current without saturating and its copper resistance in the winding should be as low as possible to minimize its resistive power loss. A good trade-off among its size, loss and cost is to set the inductor ripple current to be within 15% to 30% of the maximum output current. The inductor value can be determined according to its operating point under its continuous mode and the switching frequency as follows:
L= VO ( VI - VO ) VI fs IOMAX
Where: ILRMS is the RMS current in the inductor. This current can be calculated as follows:
ILRMS = IOMAX 1 + 12 12
Output Capacitor Selection Basically there are two major factors to consider in selecting the type and quantity of the output capacitors. The first one is the required ESR (Equivalent Series Resistance) which should be low enough to reduce the output voltage deviation during load changes. The second one is the required capacitance, which should be high enough to hold up the output voltage. Before the SC4517A regulates the inductor current to a new value during a load transient, the output capacitor delivers all
8 www.semtech.com
2006 Semtech Corp.
SC4517A
POWER MANAGEMENT Application Information (Cont.)
the additional current needed by the load. The ESR and ESL of the output capacitor, the loop parasitic inductance between the output capacitor and the load combined with inductor ripple current are all major contributors to the output voltage ripple. Surface mount ceramic capacitors are recommended. Input Capacitor Selection The input capacitor selection is based on its ripple current level, required capacitance and voltage rating. This capacitor must be able to provide the ripple current by the switching actions. For the continuous conduction mode, the RMS value of the input capacitor current ICIN(RMS) can be calculated from:
ICIN (RMS ) VO ( VI - VO ) = IOMAX V 2I TW = 1 Dmax fs
Where: fs = the switching frequency and Dmax = maximum duty ratio, 0.9 for the SC4517A. The required minimum capacitance for the boost capacitor will be:
Cboost = IB TW VD
Where: IB = the boost current and VD= discharge ripple voltage. With fs = 1.2MHz, VD = 0.5V and IB =0.045A, the required minimum capacitance for the boost capacitor is:
Cboost = IB 1 0.045 1 Dmax = 0.9 = 67.5nF VD fs 0.5 1.2M
This current gives the capacitor's power loss through its RCIN(ESR) as follows:
PCIN = I2 CIN(RMS ) * R CIN(ESR )
The input ripple voltage mainly depends on the input capacitor's ESR and its capacitance for a given load, input voltage and output voltage. Assuming that the input current of the converter is constant, the required input capacitance for a given voltage ripple can be calculated by:
CIN = IOMAX D (1 - D) fs ( VI - IOMAX R CIN(ESR ) )
The internal driver of the switch requires a minimum 2.7V to fully turn on that switch to reduce its conduction loss. If the output voltage is less than 2.7V, the boost capacitor can be connected to either the input side or an independent supply with a decoupling capacitor. But the Pin BST should not see a voltage higher than its maximum rating. Freewheeling Diode Selection This diode conducts during the switch's off-time. The diode should have enough current capability for full load and short circuit conditions without any thermal concerns. Its maximum repetitive reverse block voltage has to be higher than the input voltage of the SC4517A. A low forward conduction drop is also required to increase the overall efficiency. The freewheeling diode should be turned on and off fast with minimum reverse recovery because the SC4517A is designed for high frequency applications. SS13 Schottky rectifier is recommended for certain applications. The average current of the diode, ID_AVG can be calculated by:
ID _ AVG = IO max (1 - D)
Where: VI = the given input voltage ripple. Because the input capacitor is exposed to the large surge current, attention is needed for the input capacitor. If tantalum capacitors are used at the input side of the converter, one needs to ensure that the RMS and surge ratings are not exceeded. For generic tantalum capacitors, it is suggested to derate their voltage ratings at a ratio of about two to protect these input capacitors. Boost Capacitor and its Supply Source Selection The boost capacitor selection is based on its discharge ripple voltage, worst case conduction time and boost current. The worst case conduction time Tw can be estimated as follows:
2006 Semtech Corp. 9
www.semtech.com
SC4517A
POWER MANAGEMENT Application Information (Cont.)
Thermal Considerations There are three major power dissipation sources for the SC4517A. The internal switch conduction loss, its switching loss due to the high frequency switching actions and the base drive boost circuit loss. These losses can be estimated as:
Ptotal = Io Ron D + 22.5 10 -3 Io VI +
2
G VD (s) =
2.5 R L s 1+ 1 RL C
10 Io D ( Vboost ) 500
Where: RL - Load and C - Output capacitor. The goal of the compensation design is to shape the loop to have a high DC gain, high bandwidth, enough phase margin, and high attenuation for high frequency noises. Figure 3 gives a typical compensation network which offers 2 poles and 1 zero to the power stage:
Where: IO = load current; R = on-equivalent resistance of the switch; ON VBOOST = input voltage or output based on the boost circuit connection. The junction temperature of the SC4517A can be further decided by:
TJ = TA + JA Ptotal
1
SC4517
SW FB 3 6 7
JA is the thermal resistance from junction to ambient. Its value is a function of the IC package, the application layout and the air cooling system. It is recommended that a big copper area attached to Pin 4 or the thermal pad be used for better cooling condition. The freewheeling diode also contributes a significant portion of the total converter loss. This loss should be minimized to increase the converter efficiency by using Schottky diodes with low forward drop (VF).
Pdiode = VF Io (1 - D )
L1
IN EN SYNC
BST
2 5 8
Vout
R1 C
GND 4
COMP
C4 C5 R3 D2
R2
Figure 3. Compensation network provides 2 poles and 1 zero. The compensation network gives the following characteristics:
s Z R2 gm GCOMP (s) = 1 s R1 + R 2 s (1 + ) P 2 1+
Loop Compensation Design The SC4517A has an internal error amplifier and requires a compensation network to connect between the COMP pin and GND pin as shown in Figure 3. The compensation network includes C4, C5 and R3. R1 and R2 are used to program the output voltage according to:
R VO = 1.2 * (1 + 1 ) R2
Where:
1 = Z = P 2 = 1 C 4 + C5 1 R3 C4
Assuming the power stage ESR (equivalent series resistance) zero is an order of magnitude higher than the closed loop bandwidth, which is typically one tenth of the switching frequency, the power stage control to output transfer function with the current loop closed (Ridley model) for the SC4517A will be as follows:
2006 Semtech Corp. 10
C 4 + C5 R 3 C 4 C5
www.semtech.com
SC4517A
POWER MANAGEMENT Application Information (Cont.)
The loop gain will be given by:
T(s) = GCOMP (s) G VD (s) = 2.125 10
-3
R R2 1 L C 4 R1 + R 2 s
1+ (1 +
s Z
s s ) (1 + ) P1 P 2
3. Select Z such that it is placed at P1 to obtain a -20dB/dec rate to go across the 0dB line. 4. Place a high frequency compensator pole P2 (P2 = fs) to get the maximum attenuation of the switching ripple and high frequency noise with the adequate phase lag at C. Layout Guidelines: In order to achieve optimal electrical and thermal performance for high frequency converters, special attention must be paid to the PCB layouts. The goal of layout optimization is to identify the high di/dt loops and minimize them. The following guidelines should be used to ensure proper operation of the converters. 1. A ground plane is suggested to minimize switching noises and trace losses and maximize heat transferring. 2. Start the PCB layout by placing the power components first. Arrange the power circuit to achieve a clean power flow route. Put all power connections on one side of the PCB with wide copper filled areas if possible. 3. The VIN bypass capacitor should be placed next to the VIN and GND pins. 4. The trace connecting the feedback resistors to the output should be short, direct and far away from any noise sources such as switching node and switching components. 5. Minimize the loop including input capacitor, the SC4517A and freewheeling diode D2. This loop passes high di/dt current. Make sure the trace width is wide enough to reduce copper losses in this loop. 6. Maximize the trace width of the loop connecting the inductor, freewheeling diode D 2 and the output capacitor. 7. Connect the ground of the feedback divider and the compensation components directly to the GND pin of the SC4517A by using a separate ground trace. 8. Connect Pin 4 to a large copper area to remove the IC heat and increase the power capability of the SC4517A. A few feedthrough holes are required to connect this large copper area to a ground plane to further improve the thermal environment of the SC4517A. The traces attached to other pins should be as wide as possible for the same purpose.
Where:
1 p1 = RL C
For 1.8V, 2.5V, 3.3V and 5V out applications, their respective fixed output parts can be used. The FB pins are connected directly to the outputs. The voltage dividers (R 1 and R 2) have been integrated into the SC4517A controllers. For other output cases, the adjustable SC4517A should be used with an external voltage divider. One integrator is added at origin to increase the DC gain. Z is used to cancel the power stage pole P1 so that the loop gain has -20dB/dec rate when it reaches 0dB line. P2 is placed at half switching frequency to reject high frequency switching noises. Figure 4 gives the asymptotic diagrams of the power stage with current loop closed and its loop gain.
Loop gain T(s) p1 Power stage C Z P2
Figure 4. Asymptotic diagrams of power stage with current loop closed and its loop gain. The design guidelines for the SC4517A applications are as following: 1. Set the loop gain crossover corner frequency C for given switching corner frequency C = 2f . c 2. Place an integrator at the origin to increase DC and low frequency gains.
2006 Semtech Corp. 11
www.semtech.com
SC4517A
POWER MANAGEMENT Application Information (Cont.)
Design Example 1. 12V to 3.3V.
C1 0.1u
D3 L1
VI=12V
C3 2.2u 4.75k R4
IN EN
BST
2 5 8
SW FB
3 4.7uH 6 7 C4 1.5n R3 4.75k R1 17.4k C2 2.2u
Vo=3.3V
SYNC
GND 4
1 COMP
SC4517A
C5 100p
R2 10k
D2
Bill of Materials
Item 1 2 3 4 5 6 7 8 9 10 11 Qty 1 2 1 1 1 1 1 1 1 2 1 C1 C 2, C 3 C4 C5 D3 D2 L1 R1 R2 R3, R4 U1 Reference Value 0.1uF, 25V, 0805, X7R 2.2uF 1.5nF 100pF 1N4148WS, SOD-23 S S 13 4.7uH, 17.4k 10k 4.75k S C 4517A Semtech P/N: SC4517AIMLTRT Fairchild P/N: SS13 Cooper P/N: DR73-4R7 TDK P/N: C3216X7R1E225K Part No./Manufacturer
Unless specified, all resistors have 1% precision with 0603 package. Resistors are +/-1% and all capacitors are +/-20%
2006 Semtech Corp.
12
www.semtech.com
SC4517A
POWER MANAGEMENT PCB Layout
(COMPONENT - TOP) (COMPONENT - BOTTOM)
(PCB - TOP)
(PCB - BOTTOM)
2006 Semtech Corp.
13
www.semtech.com
SC4517A
POWER MANAGEMENT Outline Drawing - MSOP-8
e/2 A N 2X E/2 PIN 1 INDICATOR ccc C 2X N/2 TIPS 12 e B E1 E D
DIM
A A1 A2 b c D E1 E e L L1 N 01 aaa bbb ccc
DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX
.043 .000 .006 .030 .037 .015 .009 .003 .009 .114 .118 .122 .114 .118 .122 .193 BSC .026 BSC .016 .024 .032 (.037) 8 0 8 .004 .005 .010 1.10 0.00 0.15 0.75 0.95 0.22 0.38 0.08 0.23 2.90 3.00 3.10 2.90 3.00 3.10 4.90 BSC 0.65 BSC 0.40 0.60 0.80 (.95) 8 0 8 0.10 0.13 0.25
aaa C SEATING PLANE
D A2 A GAGE PLANE 0.25
H c
C
A1 bxN bbb C A-B D
L (L1) DETAIL
01
A
SIDE VIEW
NOTES: 1.
SEE DETAIL
A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD MO-187, VARIATION AA.
Land Pattern - MSOP-8
X
DIM
(C) G Z C G P X Y Z
DIMENSIONS INCHES MILLIMETERS
(.161) .098 .026 .016 .063 .224 (4.10) 2.50 0.65 0.40 1.60 5.70
Y P
NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET.
2006 Semtech Corp.
14
www.semtech.com
SC4517A
POWER MANAGEMENT Outline Drawing - MLPD-8, 3 x 3mm
A E
B
DIM
A A1 A2 b C D E e L N aaa bbb
DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX
.031 .035 .039 .000 .001 .002 (.008) .010 .012 .014 .088 .094 .098 .059 .065 .069 .114 .118 .122 .026 BSC .012 .016 .020 8 .003 .004 0.80 0.90 1.00 0.00 0.02 0.05 (0.20) 0.25 0.30 0.35 2.23 2.38 2.48 1.50 1.65 1.75 2.90 3.00 3.10 0.65 BSC 0.30 0.40 0.50 8 0.08 0.10
E PIN 1 INDICATOR (LASER MARK)
A aaa C C 1 LxN 2 A1 A2 C
SEATING PLANE
D
N e e/2
NOTES:
bxN bbb
CAB
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS.
Land Pattern - MLPD-8, 3 x 3mm
K Y
DIM
G Z C G H K P X Y Z
DIMENSIONS INCHES MILLIMETERS
(.116) .087 .067 .102 .026 .016 .030 .146 (2.95) 2.20 1.70 2.58 0.65 0.40 0.75 3.70
C
H
X P
NOTES: 1.
THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET.
Contact Information
Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804
2006 Semtech Corp. 15 www.semtech.com


▲Up To Search▲   

 
Price & Availability of SC4517AIMSXXTRT

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X