View W83L951FG_1335813.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Winbond Mobile Keyboard and Embedded Controller W83L951DG W83L951FG
Date:
August/2006
Revision: 1.00
W83L951DG/W83L951FG
W83L951DG/W83L951FG Data Sheet Revision History
PAGES DATES VERSION WEB VERSION MAIN CONTENTS
1 2 3 4 5 6 7 8 9 10
n.a.
8/7/2006
1.0
1.0
First Release
-1-
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Table of Contents1. 2. 3. 4. 5. GENERAL DESCRIPTION ......................................................................................................... 1 PRODUCT FEATURES .............................................................................................................. 2 BLOCK DIAGRAM ...................................................................................................................... 4 PIN CONFIGURATION FOR W83L951DG/W83L951FG........................................................... 5 PIN DESCRIPTION..................................................................................................................... 7 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 6. 6.1 6.2 6.3 6.4 6.5 6.6 Pin configuration table..............................................................................................................7 RESET# & TEST# Part..........................................................................................................15 LPC Interface Part..................................................................................................................16 GPIO0 Part .............................................................................................................................16 GPIO1 Part .............................................................................................................................18 GPIO2 Part .............................................................................................................................19 GPIO3 Part .............................................................................................................................20 GPIO4 Part .............................................................................................................................21 GPIO5 Part .............................................................................................................................22 GPIO6 Part .............................................................................................................................22 GPIO7 Part .............................................................................................................................23 GPIO8 Part .............................................................................................................................24 GPIO9 Part .............................................................................................................................25 GPIOA Part.............................................................................................................................26 GPIOB Part.............................................................................................................................26 GPIOC Part ............................................................................................................................27 Power & Clock Part ................................................................................................................28 Turbo 8051 Core Block ..........................................................................................................31
6.1.1 6.2.1 6.3.1 6.4.1 6.5.1 6.6.1 6.6.2 Register Description ...................................................................................................32 Register Description ...................................................................................................38 Register Description ...................................................................................................43 Register Description ...................................................................................................49 Register Description ...................................................................................................54 GPIO Data Register Description.................................................................................58 GPIO Direction Register Description ..........................................................................61 Register Description ...................................................................................................63
FUNCTIONAL DESCRIPTION.................................................................................................. 29
Low Pin Count Interface Block...............................................................................................38 Personal System 2 Block .......................................................................................................43 System Management Bus Block............................................................................................48 Internal Interrupt Controller Block ..........................................................................................53 GPIOs Block ...........................................................................................................................57
6.7
Watch Dog Block....................................................................................................................63
6.7.1
-2-
W83L951DG/W83L951FG
6.8 6.9 6.10 6.11 6.12 6.13 6.14 6.15 6.16 6.17 Timer Block.............................................................................................................................65
6.8.1 6.9.1 6.10.1 6.11.1 6.12.1 6.13.1 6.14.1 6.15.1 6.16.1 6.17.1 6.17.2 6.17.3 6.17.4 6.17.5 6.17.6 6.17.7 6.17.8 6.17.9 Register Description ...................................................................................................65 Register Description ...................................................................................................70 Register Description ...................................................................................................72 Register Description ...................................................................................................75 Register Description ...................................................................................................80 Register Description ...................................................................................................81 Register Description ...................................................................................................82 Register Description ...................................................................................................83 Register Description ...................................................................................................85 External Programming Mode ......................................................................................88 Internal Programming Mode .......................................................................................88 Device Bus Operation.................................................................................................89 Command Definitions .................................................................................................89 Write Operation Status ...............................................................................................91 Table of Operating Modes ..........................................................................................92 Embedded Algorithm ..................................................................................................93 Timing Parameters .....................................................................................................96 Timing Waveforms......................................................................................................97
Pulse Width Modulator Block.................................................................................................69 UART Block ............................................................................................................................72 Consumer Infrared Communications Receiver Block...........................................................75 A/D Converter Block...............................................................................................................80 D/A Converter Block...............................................................................................................81 Fan Tachometer Block...........................................................................................................82 Real Time Clock Generator Block .........................................................................................83 External Interrupt Control Block .............................................................................................85 Flash Memory.........................................................................................................................88
7.
SPECIFICATIONS .................................................................................................................. 101 7.1 7.2 Absolute Maximum Ratings .................................................................................................101 Analog Characteristics .........................................................................................................101
7.2.1 7.2.2 ADC Characteristics .................................................................................................101 DAC Characteristics .................................................................................................101
7.3 7.4 8. 9. 10. 11.
Power Supply Current Consumption ...................................................................................101 DC Characteristics ...............................................................................................................102
ORDERING INSTRUCTION ................................................................................................... 104 HOW TO READ THE TOP MARKING.................................................................................... 105 PACKAGE DIMENSIONS ....................................................................................................... 106 DEMO CIRCUITS ................................................................................................................... 107
-3-
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
1. GENERAL DESCRIPTION
The Winbond mobile keyboard and embedded controller W83L951DG/FG architecture consists of a Turbo-8051 core logic controller and surrounded by various components, 2K+256 bytes of RAM, 64K on-chip FLASH, LPC host interface, 13 general purpose I/O port with 24 external interrupt source, 4 timers, 1 serial port, 2 SMBus interface for master mode, 3 PS/2 port, 2 PWM channels with 8-bits and 2 PWM channels with 16-bits, 2 D-A and 8 A-D converters, 1 Consumer Infrared Communications Receiver, 2 Fan Tachometer , 1 Real Time Clock Generator, and Matrix Interface. The part number with an affix of "G" is the Lead-free package product.
-1-
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
2. PRODUCT FEATURES
Core logic 8-bit Turbo 8052 Microprocessor Code based, Speed up to 24MHz 256 bytes Internal RAM 64K bytes Embedded Programmable Flash Memory 2K bytes External SRAM Host interface Software Optional with LPC Interface Primary Programmable I/O Address Communication Port in LPC Mode Support SERIRQ in LPC Interface Support Hardware Fast Gate A20 and KBRST Support Port 92h SMBus Support 2 SMBus Interface support Master Mode. Timers Support Four Timer Signal with Three Pre-scalars Timer 1 and 2 Shard the Same Pre-scalar and are Free-Running Only. Timer X and Y Have Individual Pre-scalar and Support up to Four Control Modes, Free Running, Pulse Output, Event Counter and Pulse Width Measurement PWM Support Four PWM Channels PWM 0 and 1 are 8-bits and Programmable Frequency from 62Hz to 7.5 KHz PWM 2 and 3 are 16-bits and Programmable Frequency from 6Hz to 3MHz Fan Tachometer Support two Fan Tachometer Inputs A/D Converter Firmware Programmable Optional with 10-bite or 8-bit Resolution Support Eight Channels
-2-
W83L951DG/W83L951FG
D/A Converter 8-bit Resolution Support Two Channels PS2 Support Three Hardware PS2 Channels Optional PS2 Clock Inhibit by Hardware or Firmware Keyboard Controller Support 16*8 Keyboard Matrix-scan, Expanding to 18*8 and 20*8 GPIO Support 104 Useful GPIO Pins Totally and Bit-addressable to Facility Firmware Coding FLASH Support External On-Board 64K Flash via Matrix Interface (GP0, 1, 3) CIR Support Decoding for the NEC Consumer IR Remote Control Format RTC Real Time Clock Generator with 32.768 KHz Input ACPI Support ACPI Appliance Secondary Programmable I/O Address Communication Port in LPC Mode Package -Pin QFP and 128-Pin LQFP Leadfree Package Options, in compliance with the RoHS (Restriction on Hazardous Substances)
-3-
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
3. BLOCK DIAGRAM
Internal Reset
Watch Dog Timer
LRESET#
8051 Core LPC Interface 256 Byte RAM
LCLK LFRAME# LAD0~LAD3 SERIRQ CLKRUN# KBRST# GATE_A20
CNTR0
Timer
CNTR1
PWM0 PWM1 PWM2 PWM3
Pulse Width Modulator
2K Byte RAM
GPIOs
GP0~GPC
UARTTX
UART
UARTRX
Flash 64K Byte
Martix Interface
M_KR0~M_KR7 M_KC0~M_KC16
KPS2CLK CIRRX
CIR
FAN
FAN1 FAN2
KPS2DAT
PS2
MPS2CLK MPS2DAT
AD7~AD0
ADC External Interrupt Controller
EXTINT1 EXTINT2 EXTINT3
APS2CLK APS2DAT
DA1~DA0
DAC
SDA1 SCL1
XCIN
RTC
Internal RAM Bus External RAM Bus
SMBus
SDA2 SCL2
Note: This Block Diagram should not used for pin count.
-4-
W83L951DG/W83L951FG
4. PIN CONFIGURATION FOR W83L951DG/W83L951FG
128-Pin Low Profile Quad Flat Pack (LQFP)
W83L951DG
Note: The Pin Configuration is only for 128-pin LQFP Package.
-5-
Publication Release Date: August 2006 Revision 1.0
128-Pin Quad Flat Pack (QFP)
Note: The Pin Configuration is only for 128-pin QFP Package.
W83L951FG
-6-
ODO5/EXTINT35/GPC5 ODO4/EXTINT34/GPC4 ODO3/EXTINT33/GPC3 ODO2/EXTINT32/GPC2 ODO1/EXTINT31/GPC1 ODO0/EXTINT30/GPC0 ODI7/EXTINT27/GPB7 ODI6/EXTINT26/GPB6 ODI5/EXTINT25/GPB5 ODI4/EXTINT24/GPB4 ODI3/EXTINT23/GPB3 ODI2/EXTINT22/GPB2 ODI1/EXTINT21/GPB1 ODI0/EXTINT20/GPB0 OA7/EXTINT17/GPA7 OA6/EXTINT16/GPA6 OA5/EXTINT15/GPA5 OA4/EXTINT14/GPA4 OA3/EXTINT13/GPA3 OA2/EXTINT12/GPA2 OA1/EXTINT11/GPA1 OA0/EXTINT10/GPA0 VCC1 FOEHV/GP97 FWEHV/GP96 FCEHV/GP95 FA9HV/GP94 FA13HV/GP93 FA14HV/GP92 FA15HV/GP91 GP90 GND OM1/GP87 OM0/GP86 GP85 CIR_RX/GP84 CNTR1/GP83 CNTR0/GP82 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
GP30/M_KR0/(FD0) GP31/M_KR1/(FD1) GP32/M_KR2/(FD2) GP33/M_KR3/TS(FD3) GP34/M_KR4/ALE(FD4) GP35/M_KR5/FWEN#/(FD5) GP36/M_KR6/FOEN#/(FD6) GP37/M_KR7/FCEN#/(FD7) GP00/M_KC0/FA0/FD0 GP01/M_KC1/FA1/FD1 GP02/M_KC2/FA2/FD2 GP03/M_KC3/FA3/FD3 GP04/M_KC4/FA4/FD4 GP05/M_KC5/FA5/FD5 GP06/M_KC6/FA6/FD6 GP07/M_KC7/FA7/FD7 GP10/M_KC8/FA8 GP11/M_KC9/FA9 GP12/M_KC10/FA10 GP13/M_KC11/FA11 GP14/M_KC12/FA12 GP15/M_KC13/FA13 GP16/M_KC14/FA14 GP17/M_KC15/FA15 VCC1 GP20/nM_KC16 GP21/nM_KC17 GP22/nM_KC18 GP23/nM_KC19 GP24/PWM1 GP25/PWM2 GP26/PWM3 GP27/PWM4 GND GP40/FAN_TACH1 GP41/FAN_TACH2 GP42/RXD GP43/TXD
W83L951DG/W83L951FG
W83L951DG/W83L951FG
5. PIN DESCRIPTION
Table 5-1 Pin Type Description
TYPE DESCRIPTION
I/O12tsm I/O12tsai I/O12tsao I/O16tsh I/O24ts Its Ic, Oc Ivdd Ivss
Bi-directional pin, TTL level, Schmitt-trigger input, selectable 250uA/12mA sink capability, 12mA select source capability Bi-directional pin, TTL level, Schmitt-trigger input, Analog Input, 12mA source-sink capability Bi-directional pin, TTL level, Schmitt-trigger input, Analog Output, 12mA source-sink capability Bi-directional pin, TTL level, Schmitt-trigger input, 5V Tolerant, 16mA source-sink capability Bi-directional pin, Schmitt-trigger input, 24mA source-sink capability TTL level, Schmitt-trigger input Clock Input, Clock Out Voltage Input Ground Input
Note: t - TTL level, s - Schmitt-trigger, m - matrix keyboard, ai - analog input, ao - analog output, h - 5V Tolerant, c - clock.
5.1
Pin configuration table
SYMBOL PIN I/O FUNCTION
Table 5-2 Pin configuration table GPC5 EXTINT35 GPC4 EXTINT34 GPC3 EXTINT33 GPC2 EXTINT32 GPC1 EXTINT31 GPC0 EXTINT30 GPB7 EXTINT27 General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input
1 2 3 4 5 6 7
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
-7-
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GPB6 EXTINT26 GPB5 EXTINT25 SYMBOL GPB4 EXTINT24 GPB3 EXTINT23 GPB2 EXTINT22 GPB1 EXTINT21 GPB0 EXTINT20 GPA7 EXTINT17 GPA6 EXTINT16 GPA5 EXTINT15 GPA4 EXTINT14 GPA3 EXTINT13 GPA2 EXTINT12 GPA1 EXTINT11 GPA0 EXTINT10 VCC1 GP97
8 9 PIN 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
I/O16tsh I/O16tsh I/O I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh Ivdd I/O16tsh
General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input FUNCTION General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input Normal Power Input, +3.3V General Purpose I/O Function
-8-
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP96 GP95 GP94 GP93 GP92 GP91 GP90 GND GP87 GP86 GP85 GP84 CIR_RX GP83 CNTR1 GP82 CNTR0 GP81 SCL2 SYMBOL GP80 SDA2 GP77 SCL1 GP76 SDA1 GP75 APS2_DAT GP74 APS2_CLK GP73 MPS2_DAT
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 PIN 40 41 42 43 44 45
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh Ivss I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function Normal GND General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function Consumer Infrared Communication Receiver Function General Purpose I/O Function Timer Y Signal General Purpose I/O Function Timer X Signal General Purpose I/O Function SMBus 2 Clock Signal FUNCTION General Purpose I/O Function SMBus 2 Data Signal General Purpose I/O Function SMBus 1 Clock Signal General Purpose I/O Function SMBus 1 Data Signal General Purpose I/O Function Auxiliary PS2 Data Signal General Purpose I/O Function Auxiliary PS2 Clock Signal General Purpose I/O Function Mouse PS2 Data Signal
-9-
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP72 MPS2_CLK GP71 KPS2_DAT GP70 KPS2_CLK VCC1 RESET# LCLK
46 47 48 49 50 51
I/O16tsh I/O16tsh I/O16tsh Ivdd Its Its
General Purpose I/O Function Mouse PS2 Clock Signal General Purpose I/O Function Keyboard PS2 Data Signal General Purpose I/O Function Keyboard PS2 Clock Signal Normal Power Input, +3.3V System Reset. PCI clock input. Same 33MHz clock as PCI clock on the host. Same clock phase with typical PCI skew. Indicates start of a new cycle or termination of a broken cycle. Reset signal. It can connect to PCIRST# signal on the host. Serial IRQ input/Output. Normal GND LAD[3..0] are multiplexed address, control, and data in LPC bus. LAD[3..0] are multiplexed address, control, and data in LPC bus. LAD[3..0] are multiplexed address, control, and data in LPC bus. LAD[3..0] are multiplexed address, control, and data in LPC bus. Power status. Indicates current power status of LPC interface. General Purpose I/O Function General Purpose I/O Function Advance LPC function: It is used to request starting the clock General Purpose I/O Function Gate A20 output General Purpose I/O Function CPU reset output
LFRAME# LRESET# SERIRQ GND LAD0 LAD1 LAD2 LAD3 LPWRSTS GP47 GP46 CLKRUN# GP45 GATE_A20 GP44 KBRST#
52 53 54 55 56 57 58 59 60 61 62
Its Its I/O24ts Ivss I/O24ts I/O24ts I/O24ts I/O24ts Its I/O16tsh I/O16tsh
63 64
I/O16tsh I/O16tsh
- 10 -
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP43 TXD GP42 RXD GP41 FAN_TACH1 GP40 FAN_TACH0 SYMBOL GND GP27 PWM3 GP26 PWM2 GP25 PWM1 GP24 PWM0 GP23 KC19 GP22 KC18 GP21 KC17 GP20 KC16 VCC1 GP17 KC15 FA15
65 66 67 68 PIN 69 70 71 72 73 74 75 76 77 78 79
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O Ivss I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O12tsm I/O12tsm I/O12tsm I/O12tsm Ivdd I/O12tsm
General Purpose I/O Function UART TX output General Purpose I/O Function UART RX Input General Purpose I/O Function Fan tachometer 1 General Purpose I/O Function Fan tachometer 0 FUNCTION Normal GND General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Keyboard Matrix Column Output General Purpose I/O Function Keyboard Matrix Column Output General Purpose I/O Function Keyboard Matrix Column Output General Purpose I/O Function Keyboard Matrix Column Output Normal Power Input, +3.3V General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address
- 11 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP16 KC14 FA14 GP15 KC13 FA13 GP14 KC12 FA12 GP13 KC11 FA11 GP12 KC10 FA10 GP11 KC9 FA9 GP10 KC8 FA8 GP07 KC7 FA7/FD7 GP06 KC6 FA6/FD6 SYMBOL GP05 KC5 FA5/FD5 89 I/O12tsm PIN I/O 88 I/O12tsm 87 I/O12tsm 86 I/O12tsm 85 I/O12tsm 84 I/O12tsm 83 I/O12tsm 82 I/O12tsm 81 I/O12tsm 80 I/O12tsm
General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data FUNCTION General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data
- 12 -
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP04 KC4 FA4/FD4 GP03 KC3 FA3/FD3 GP02 KC2 FA2/FD2 GP01 KC1 FA1/FD1 GP00 KC0 FA0/FD0 GP37 KR7 CE# GP36 KR6 OE# GP35 KR5 WE# GP34 KR4 ALE GP33 KR3 GP32 KR2 99 100 I/O16tsh I/O16tsh 98 I/O16tsh 97 I/O16tsh 96 I/O16tsh 95 I/O16tsh 94 I/O12tsm 93 I/O12tsm 92 I/O12tsm 91 I/O12tsm 90 I/O12tsm
General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Flash chip select enable General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Flash output enable General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Flash write enable General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Address latch enable General Purpose I/O Function Keyboard Matrix Row Input General Purpose I/O Function Keyboard Matrix Row Input
- 13 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP31 KR1 GP30 KR0 VREF GP67 AD7 GP66 AD6 GP65 AD5 GP64 AD4 SYMBOL GP63 AD3 GP62 AD2 GP61 AD1 GP60 AD0 AVCC GP57 DA2 GP56 DA1 AGND GP55 GP54 GP53 GP52
101 102 103 104 105 106 107 PIN 108 109 110 111 112 113 114 115 116 117 118 119
I/O16tsh I/O16tsh Ivdd I/O12tsao I/O12tsao I/O12tsao I/O12tsao I/O I/O12tsao I/O12tsao I/O12tsao I/O12tsao Ivdd I/O12tsai I/O12tsai Ivss I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function Keyboard Matrix Row Input General Purpose I/O Function Keyboard Matrix Row Input Analog Reference Voltage Input General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal FUNCTION General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal Analog Power Input, +3.3V General Purpose I/O Function DA Converter Output General Purpose I/O Function DA Converter Output Analog GND General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function
- 14 -
W83L951DG/W83L951FG
Pin configuration table, continued.
SYMBOL
PIN
I/O
FUNCTION
GP51 GP50 XOUT XIN TEST# XCOUT XCIN GPC7 EXTINT37 GPC6 EXTINT36
120 121 122 123 124 125 126 127 128
I/O16tsh I/O16tsh Oc Ic Its Oc Ic I/O16tsh I/O16tsh
General Purpose I/O Function General Purpose I/O Function 24MHz/12MHz System Clock Output 24MHz/12MHz System Clock Input Test pin to provide different operation. 32.768 KHz Clock Output 32.768 KHz Clock Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input
5.2
RESET# & TEST# Part
SYMBOL PIN I/O FUNCTION
Table 5-3 RESET# & TEST# pin configuration table RESET# TEST# 50 124 Its Its System Reset. Test pin to provide different operation.
In W83L951DG/FG, RESET# Pin and TEST# Pin decide the status of W83L951DG/FG to provide 4 operations.
TEST# RESET# CHIP CURRENT STATUS
0 0 1 1
0 1 0 1
Internal Flash Access Interface Enable Reserved Normal Reset Normal Operation
- 15 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
5.3 LPC Interface Part
LPC Interface is formed by LAD0~LAD3, SERIRQ, LRESET#, LFRAME#, LCLK and VCC2. These pins are defined by LPC interface Spec except VCC2. Below are descriptions about all LPC pins: Table 5-4 LPC interface pin configuration table
SYMBOL PIN I/O FUNCTION
LCLK LFRAME# LRESET# SERIRQ LAD0 LAD1 LAD2 LAD3
51 52 53 54 56 57 58 59
Its Its Its I/O24ts I/O24ts I/O24ts I/O24ts I/O24ts
PCI clock input. Same 33MHz clock as PCI clock on the host. Same clock phase with typical PCI skew. Indicates start of a new cycle or termination of a broken cycle. Reset signal. It can connect to PCIRST# signal on the host. Serial IRQ input/Output. LAD[3..0] are multiplexed address, control, and data in LPC bus. LAD[3..0] are multiplexed address, control, and data in LPC bus. LAD[3..0] are multiplexed address, control, and data in LPC bus. LAD[3..0] are multiplexed address, control, and data in LPC bus.
Note: Other pins about LPC interface, CLKRUN#: Please see "GP4" part.VCC2: Please see "power & clock" part.
5.4
GPIO0 Part
This part contains: General Purpose I/O Function Default is General Purpose I/O. Change the value of GPIO0 and GPIOD0 register to determine 8 input/output. Keyboard Matrix Column Output Use Chipctrl2 register bit 3 to enable {GP0, GP1, GP20~23} keyboard scan and GP3 key wakeup interrupt function. Internal Flash Access Interface When TEST# and RESET# are both low, Internal Flash Access Interface is enabled and other functions are disabled.
- 16 -
W83L951DG/W83L951FG
Table 5-5 GPIO0 pin configuration table
SYMBOL PIN I/O FUNCTION
GP07 KC7 FA7/FD7 GP06 KC6 FA6/FD6 GP05 KC5 FA5/FD5 GP04 KC4 FA4/FD4 GP03 KC3 FA3/FD3 GP02 KC2 FA2/FD2 GP01 KC1 FA1/FD1 GP00 KC0 FA0/FD0 94 I/O12tsm 93 I/O12tsm 92 I/O12tsm 91 I/O12tsm 90 I/O12tsm 89 I/O12tsm 88 I/O12tsm 87 I/O12tsm
General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address/ Internal Flash Data
- 17 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
5.5 GPIO1 Part
This part contains: General Purpose I/O Function Default is General Purpose I/O. Change the value of GPIO1 and GPIOD1 register to determine 8 input/output. Keyboard Matrix Column Output Use Chipctrl2 register bit 3 to enable {GP0, GP1, GP20~23} keyboard scan and GP3 key wakeup interrupt function. Internal Flash Access Interface When TEST# and RESET# are both low, Internal Flash Access Interface is enabled and other functions are disabled. Table 5-6 GPIO1 pin configuration table
SYMBOL PIN I/O FUNCTION
GP17 KC15 FA15 GP16 KC14 FA14 GP15 KC13 FA13 GP14 KC12 FA12 GP13 KC11 FA11 GP12 KC10 FA10 GP11 KC9 FA9 GP10 KC8 FA8
79
I/O12tsm
80
I/O12tsm
81
I/O12tsm
82
I/O12tsm
83
I/O12tsm
84
I/O12tsm
85
I/O12tsm
86
I/O12tsm
General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address General Purpose I/O Function Keyboard Matrix Column Output Internal Flash Address
- 18 -
W83L951DG/W83L951FG
5.6 GPIO2 Part
This part contains: General Purpose I/O Function Default is General Purpose I/O. Change the value of GPIO2 and GPIOD2 register to determine 8 input/output. Pulse Width Modulator Output Use Pulse Width Modulator Registers to control 4 Pulse Width Modulator Output. Keyboard Matrix Column Output Change the value of chip control 2 register bit 3 (Keyboard Scan Function Enable) to enable {GP0, GP1, GP20~23} keyboard scan function and GP3 key wakeup interrupt function. Table 5-7 GPIO2 pin configuration table
SYMBOL PIN I/O FUNCTION
GP27 PWM3 GP26 PWM2 GP25 PWM1 GP24 PWM0 GP23 KC19 GP22 KC18 GP21 KC17 GP20 KC16
70 71 72 73 74 75 76 77
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O12tsm I/O12tsm I/O12tsm I/O12tsm
General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Pulse Width Modulator Output General Purpose I/O Function Keyboard Matrix Column Output General Purpose I/O Function Keyboard Matrix Column Output General Purpose I/O Function Keyboard Matrix Column Output General Purpose I/O Function Keyboard Matrix Column Output
- 19 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
5.7 GPIO3 Part
This part contains General Purpose I/O function, external flash interface, and keyboard matrix row input. Default function is General Purpose I/O function. General Purpose I/O Function Change the value of GPIO 3 data register (GPIO3) and GPIO 3 direction register (GPIOD3) to determine 8 input/output. Keyboard Matrix Row Input Change the value of chip control 2 register bit 3 (Keyboard Scan Function Enable) to enable GP3 key wakeup interrupt function. Note: GPIO3 must be set as input when this function is enabled The sample frequency about KEY Interrupt Mode is a system cycle, trigger for ' Low ' of input of GP3 and only take a sample once (unless input of GP3 return 'High', then enter `low'). If signal debounce, then interrupt may request again. Internal Flash Access Interface GPIO30~33: Reserved (Must assign low) Table 5-8 GPIO3 pin configuration table
SYMBOL PIN I/O FUNCTION
GP37 KR7 CE# GP36 KR6 OE# GP35 KR5 WE# GP34 KR4 ALE GP33 KR3 GP32 KR2 GP31 KR1 GP30 KR0
95
I/O16tsh
96
I/O16tsh
97
I/O16tsh
98 99 100 101 102
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Flash chip select enable General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Flash output enable General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Flash write enable General Purpose I/O Function Keyboard Matrix Row Input Internal Flash Access Interface: Address latch enable General Purpose I/O Function Keyboard Matrix Row Input General Purpose I/O Function Keyboard Matrix Row Input General Purpose I/O Function Keyboard Matrix Row Input General Purpose I/O Function Keyboard Matrix Row Input
- 20 -
W83L951DG/W83L951FG
5.8 GPIO4 Part
General Purpose I/O Function Change the value of GPIO 4 data register (GPIO4) and GPIO 4 direction register (GPIOD4) to determine 8 input/output. Universal Asynchronous Serial I/O Function Change the value of chip control 1 register bit 3 (UART Function Enable) to enable Universal Asynchronous Serial I/O Function. Hardware Keyboard Reset Function Change the value of keyboard control register bit4 (Port 92 Enable) and bit3 (Hardware Keyboard Reset Control Enable) to enable Hardware Keyboard Reset Function. Hardware Gate A20 Function Change the value of keyboard control register bit4 (Port 92 Enable) and bit2 (Hardware Gate A20 Control Enable) to enable Hardware Gate A20 Function. Table 5-9 GPIO4 pin configuration table
SYMBOL PIN I/O FUNCTION
GP47 GP46 CLKRUN# GP45 GATE_A20 GP44 KBRST# GP43 TXD GP42 RXD GP41 FAN_TACH1 GP40 FAN_TACH0
61 62 63 64 65 66 67 68
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function General Purpose I/O Function Advance LPC function: It is used to request starting the clock General Purpose I/O Function Gate A20 output General Purpose I/O Function CPU reset output General Purpose I/O Function UART TX output General Purpose I/O Function UART RX Input General Purpose I/O Function Fan tachometer 1 General Purpose I/O Function Fan tachometer 0
- 21 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
5.9 GPIO5 Part
General Purpose I/O Function Change the value of GPIO 5 data register (GPIO5) and GPIO 5 direction register (GPIOD3) to determine 8 input/output. D/A Converter Function Change the value of chip control 2 register bit 7 (D/A 2 Function Enable) and Bit 6 (D/A 1 Function Enable) to enable D/A Converter Function. Table 5-10 GPIO5 pin configuration table
SYMBOL PIN I/O FUNCTION
GP57 DA2 GP56 DA1 GP55 GP54 GP53 GP52 GP51 GP50
113 114 116 117 118 119 120 121
I/O12tsai I/O12tsai I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function DA2 Converter Output General Purpose I/O Function DA1 Converter Output General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function
5.10 GPIO6 Part
General Purpose I/O Function Change the value of GPIO 6 data register (GPIO6) and GPIO 6 direction register (GPIOD6) to determine 8 input/output. A/D Converter Function Change the value of chip control 2 register bit 5 (A/D Function Enable) to enable A/D Converter Function.
- 22 -
W83L951DG/W83L951FG
Table 5-11 GPIO6 pin configuration table
SYMBOL PIN I/O FUNCTION
GP67 AD7 GP66 AD6 GP65 AD5 GP64 AD4 GP63 AD3 GP62 AD2 GP61 AD1 GP60 AD0
104 105 106 107 108 109 110 111
I/O12tsao I/O12tsao I/O12tsao I/O12tsao I/O12tsao I/O12tsao I/O12tsao I/O12tsao
General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal General Purpose I/O Function A/D Converter Input Signal
5.11 GPIO7 Part
General Purpose I/O Function Change the value of GPIO 7 data register (GPIO7) and GPIO 7 direction register (GPIOD7) to determine 8 input/output. Keyboard PS2 Function Enable Function Change the value of chip control 3 register bit 2 (Keyboard PS2 Function Enable) to enable Keyboard PS2 Function Enable Function. Mouse PS2 Function Enable Function Change the value of chip control 3 register bit 3 (Mouse PS2 Function Enable) to enable Mouse PS2 Function Enable Function. Auxiliary PS2 Function Enable Function Change the value of chip control 3 register bit 4 (Auxiliary PS2 Function Enable) to enable Auxiliary PS2 Function Enable Function. SMBUS 1 Function Change the value of chip control 3 register bit 0 (SMBUS 1 Function Enable) to enable SMBUS 1 Function.
- 23 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Table 5-12 GPIO7 pin configuration table
SYMBOL PIN I/O FUNCTION
GP77 SCL1 GP76 SDA1 GP75 APS2_DAT GP74 APS2_CLK GP73 MPS2_DAT GP72 MPS2_CLK GP71 KPS2_DAT GP70 KPS2_CLK
41 42 43 44 45 46 47 48
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function SMBus 1 Clock Signal General Purpose I/O Function SMBus 1 Data Signal General Purpose I/O Function Auxiliary PS2 Data Signal General Purpose I/O Function Auxiliary PS2 Clock Signal General Purpose I/O Function Mouse PS2 Data Signal General Purpose I/O Function Mouse PS2 Clock Signal General Purpose I/O Function Keyboard PS2 Data Signal General Purpose I/O Function Keyboard PS2 Clock Signal
5.12 GPIO8 Part
General Purpose I/O Function Change the value of GPIO 8 data register (GPIO8) and GPIO 8 direction register (GPIOD8) to determine 8 input/output. Consumer Infrared Communications Receiver Function Change the value of chip control 3 register bit 5 (CIR Function Enable) to enable Consumer Infrared Communications Receiver Function. Wave Measurement Function Change the value of timer X/Y mode register bit 5-4 and bit 1-0 to enable Wave Measurement Function. SMBUS 2 Function Change the value of chip control 2 register bit 1 (SMBUS 2 Function Enable) to enable SMBUS 2 Function.
- 24 -
W83L951DG/W83L951FG
Table 5-13 GPIO8 pin configuration table
SYMBOL PIN I/O FUNCTION
GP87 GP86 GP85 GP84 CIR_RX GP83 CNTR1 GP82 CNTR0 GP81 SCL2 GP80 SDA2
33 34 35 36 37 38 39 40
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function Consumer Infrared Communication Receiver Function General Purpose I/O Function Timer Y Signal General Purpose I/O Function Timer X Signal General Purpose I/O Function SMBus 2 Clock Signal General Purpose I/O Function SMBus 2 Data Signal
5.13 GPIO9 Part
General Purpose I/O Function Change the value of GPIO 9 data register (GPIO9) and GPIO 9 direction register (GPIOD9) to determine 8 input/output. Table 5-14 GPIO9 pin configuration table
SYMBOL PIN I/O FUNCTION
GP97 GP96 GP95 GP94 GP93 GP92 GP91 GP90
24 25 26 27 28 29 30 31
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function General Purpose I/O Function
- 25 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
5.14 GPIOA Part
General Purpose I/O Function Change the value of GPIO A data register (GPIOA) and GPIO A direction register (GPIODA) to determine 8 input/output. External Interrupt Source Input Function Change the value of external interrupt enable 1 register to determine External Interrupt. Table 5-15 GPIOA pin configuration table
SYMBOL PIN I/O FUNCTION
GPA7 EXTINT17 GPA6 EXTINT16 GPA5 EXTINT15 GPA4 EXTINT14 GPA3 EXTINT13 GPA2 EXTINT12 GPA1 EXTINT11 GPA0 EXTINT10
15 16 17 18 19 20 21 22
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input
5.15 GPIOB Part
General Purpose I/O Function Change the value of GPIO B data register (GPIOB) and GPIO B direction register (GPIODB) to determine 8 input/output. External Interrupt Source Input Function Change the value of external interrupt enable 2 register to determine External Interrupt.
- 26 -
W83L951DG/W83L951FG
Table 5-16 GPIOB pin configuration table
SYMBOL PIN I/O FUNCTION
GPB7 EXTINT27 GPB6 EXTINT26 GPB5 EXTINT25 GPB4 EXTINT24 GPB3 EXTINT23 GPB2 EXTINT22 GPB1 EXTINT21 GPB0 EXTINT20
7 8 9 10 11 12 13 14
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input
5.16 GPIOC Part
General Purpose I/O Function Change the value of GPIO C data register (GPIOC) and GPIO C direction register (GPIODC) to determine 8 input/output. External Interrupt Source Input Function Change the value of external interrupt enable 3 register to determine External Interrupt.
- 27 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Table 5-17 GPIOC pin configuration table
SYMBOL PIN I/O FUNCTION
GPC7 EXTINT37 GPC6 EXTINT36 GPC5 EXTINT35 GPC4 EXTINT34 GPC3 EXTINT33 GPC2 EXTINT32 GPC1 EXTINT31 GPC0 EXTINT30
127 128 1 2 3 4 5 6
I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh I/O16tsh
General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input General Purpose I/O Function External Interrupt Input
5.17 Power & Clock Part
Table 5-18 Power & clock pin configuration table
SYMBOL PIN I/O FUNCTION
XOUT XIN XCOUT XCIN VCC1 VCC2 GND AVCC AGND VREF
122 123 125 126 23 49 78 60 32 55 69 112 115 103
Oc Ic Oc Ic Ivdd Its Ivss Ivdd Ivss Ivdd
24MHz/12MHz System Clock Output 24MHz/12MHz System Clock Input 32.768 KHz Clock Output 32.768 KHz Clock Input Normal Power Input, +3.3V Power status. Indicates current power status of LPC interface. Normal GND Analog Power Input, +3.3V Analog GND Analog Reference Voltage Input
- 28 -
W83L951DG/W83L951FG
6. FUNCTIONAL DESCRIPTION
In W83L951DG/FG, memory organization and data type are based on Turbo 51 core controller. Register sets of various function blocks are finished by accessing Special Function Register (SFR). According to the difference of accessing approaches, SFR are divided into Address Mapping and External RAM Address Mapping. Internal RAM Address Mapping: It means to use direct addressing to access 128 bytes from internal RAM address 80H to 0FFH. Function blocks that use Internal RAM Address Mapping are listed below: Table 6-1 Reset Source Table
NAME RESET SOURCE
8051 Core Internal Interrupt Controller PS2 Device Interface Low Pin Count Interface Controller SMBus 1 SMBus 2 GPIO Controller
System Reset. System Reset System Reset + PS2 Reset System Reset + LPC Power Fail + LPC Reset System Reset + SMBUS1 Reset System Reset + SMBUS2Reset System Reset.
Table 6-2 Internal RAM Address Mapping Table
Base on 00h Offset 80 88 90 98 A0 A8 B0 B8 C0 C8 D0 D8 E0 E8 F0 F8 Index + 8 Index 0 +GP0 +GP1 +GP2 +GP3 +GP4 +GP5 +GP6 +GP7 +GP8 +GP9 +PSW +GPA +ACC +GPB +B +GPC 8 1 SP CHIPCTRL1 KBCCON DBB1STS KPS2DATA APS2DATA S1CR S1MFIFOSTS S2CR S2MFIFOSTS GPD0 GPD7 IE1 IREQ1 IP1 FCON 9 2 DPL1 CHIPCTRL2 LPCCON DBB1 KPS2CON APS2CON S1IREQ S1SFIFO S2IREQ S2SFIFO GPD1 GPD8 IE2 IREQ2 IP2 FADDH A 3 DPH1 CHIPCTRL3 DBB0STS DBB1ADDH KPS2STS APS2STS S1IE S1SCON S2IE S2SCON GPD2 GPD9 IE3 IREQ3 IP3 FADDL B 4 DPL2 DPSEL DBB0 DBB1ADDL MPS2DATA S1FIFOCON S1SSTS S2FIFOCON S2SSTS GPD3 GPDA IE4 IREQ4 IP4 FDATA C DPH2 INTEN DBB0ADDH SIRQ1 MPS2CON S1MFIFO S1SFIFOSTS S2MFIFO S2SFIFOSTS GPD4 GPDB 6 ID MMEN DBB0ADDL MPS2STS S1MCON S2MCON GPD5 GPDC 7 VERSION SIRQ0 PS2HSEN S1MSTS S2MSTS GPD6
E
F
Read Only
Reserved
+ a bit addressable register
- 29 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
External RAM Address Mapping: It means to use MOVX to access 256 bytes from external RAM addressing FF00H~FFFFH. Function blocks that use External RAM Address Mapping are listed below: Table 6-3 Reset Source Table
NAME RESET SOURCE
Watch Dog Block Timer Block PWM1/2/3/4 Block Serial I/O Block CIR Block AD Convert Block DA Convert Block External Interrupt Block FAN Block RTC Block
System Reset + WDT Reset System Reset System Reset + PWM1/2/3/4 Reset System Reset + SIO Reset System Reset + CIR Reset System Reset + AD Reset System Reset + DA Reset System Reset + System Reset. System Reset + FAN Reset System Reset + RTC Reset
Table 6-4 External RAM Address Mapping Table
Base FF00h Offset 00h 08h 10h 18h 20h 28h 30h 38h 40h 48h 50h 58h 60h 68h 70H 78H 80H 88H Index + Index 0 WDTCON PRE1 TM PWMCON PWM3HH UARTCON CIR AD1 FAN1 RTCSEC EIE1 EINTT1 8 1 WDTSTS T1 PREX PWM1P PWM4PL UARTSTS BRD AD2 FAN2 RTCSECAL RTCMIN EIE2 EINTT2 9 EIE3 EINTT3 A RTCMINAL RTCHR EIREQ1 EINTT4 B EIREQ2 C RTCHRAL EIREQ3 D E F 2 3 4 5 6 7
PRE2 TX PWM1H PWM4PH BRGH CIRFIFO DA1
T2 PREY PWM2P PWM4HL BRGL
TY PWM2H PWM4HH UARTBUF
PWM3PL
PWM3PH
PWM3HL
DA2
Read Only
Reserved
- 30 -
W83L951DG/W83L951FG
6.1 Turbo 8051 Core Block
The Turbo 8051 is fully instruction compatible. It features a faster running and better performance. It improves the performance not just by running at high frequency but also reduces the machine cycle duration from the standard 8051 period of twelve clocks to four clock cycles for the majority of instructions. This improves performance by an average of 1.5 to 3 times. The Turbo 8051 also provides dual Data Pointers (DPTRs) to speed up block data memory transfers. In W83L951DG/FG, External Wakeup Source will only be controlled by external wakeup configure register, not be influenced by internal interrupt configuration, even relevant interrupt enable or global interrupt enable have not been set, can carry out action of wakeup chip equally. Table 6-5 8051 Configure Register Define
8051 Configure Register (12) IntAddr Name 7 6 5 D0 PSW CY AC F0 E0 ACC Accumulator [7:0] F0 B B[7:0] 81 SP Stack Pointer [7:0] 82 DPL1 Data Pointer 1 [7:0] 83 DPH1 Data Pointer 1 [15:8] 84 DPL2 Data Pointer 2 [7:0] 85 DPH2 Data Pointer 2 [15:8] 86 ID Device ID Register 87 REV Device Revised Version Register 8C DPSEL 8D INTEN 8E MMC 89 CHIPCTRL1 PWM4EN PWM3EN PWM2EN 8A CHIPCTRL2 D/AEN2 D/AEN1 A/DEN 8B CHIPCTRL3 FAN2EN FAN1EN CIREN 4 RS1 3 RS0 2 OV 1 F1 0 P
PWM1EN UARTEN ALPCEN RTCEN KEYEN WDTEN APS2 MPS2 KPS2
DPS INTEN MMEN Clock Select PD IDLE SM2EN SM1EN
Table 6-6 External Wakeup Configure Register Define
POWER DOWN CONFIGURE REGISTER EXTADDR NAME 7 6 5 4 3 2 1 0
8C 8D
EXTWKP1 EXTWKP2
Reserved Reserved RTC
KEY LPC
EXTINT3 APS2
EXTINT2 MPS2
EXTINT1 KPS2
- 31 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.1.1 6.1.1.1 Register Description Program Status Word Register (PSW) (Default Value: 0000_0000)
Bit7: Carry Flag (CY): Set for an arithmetic operation, which results in a carry being generated from the ALU. It is also used as the accumulator for the bit operations. Bit6: Auxiliary Carry (AC): Set when the previous operation resulted in a carry (during addition) or borrow (during subtraction) from the high order nibble. Bit5: User Flag 0 (F0): General-purpose flag can be set or cleared by the user by software. Bit4~3: Register bank selects bits (RS1, RS0): RS1 RS0 Register bank 0 0 0 0 1 1 1 0 2 1 1 3 Bit2: Overflow Flag (OV): Address Range 00-07h 08-0Fh 10-17h 18-1Fh
Set when a carry was generated from the seventh bit but not from the 8th bit as a result of the previous operation or vice-versa. Bit1: User Flag 1 (F1): General-purpose flag that can be set or cleared by the user by software Bit0: Parity flag (P): Set/cleared by hardware to indicate odd/even number of 1's in the accumulator. Please refer to MCS-8051 define in detail.
6.1.1.2
Accumulator Register (ACC) (Default Value: 0000_0000)
Bit7~0: Accumulator (A) The A or ACC register is the standard 8032 accumulator. Please refer to MCS-8051 define in detail.
6.1.1.3
Bit7~0: B
B Register (B) (Default Value: 0000_0000)
The B register is the standard 8032 accumulator. Please refer to MCS-8051 define in detail.
6.1.1.4
Stack Pointer Register (SP) (Default Value: 0000_0111)
Bit7~0: Stack Pointer The Stack Pointer stores the Scratch-pad RAM address where the stack begins. In other words it always points to the top of the stack. Note: The address range is 00h~FFh. Please refer to MCS-8051 define in detail.
- 32 -
W83L951DG/W83L951FG
6.1.1.5 6.1.1.6 6.1.1.7 6.1.1.8 6.1.1.9 6.1.1.10 6.1.1.11 Data Pointer 1 High Byte Register (DPH1) (Default Value: 0000_0000) Data Pointer 1 Low Byte Register (DPL1) (Default Value: 0000_0000) Data Pointer 2 High Byte Register (DPH2) (Default Value: 0000_0000) Data Pointer 2 Low Byte Register (DPL1) (Default Value: 0000_0000) Device ID Register (ID) (Default Value: 0001_0010) Revised Version Register (REV) (Default Value: 0000_0000) Data Pointer Select Register (DPSEL) (Default Value: 0000_0000)
This is the high byte of the standard 8032 16-bit data pointer.
This is the low byte of the standard 8032 16-bit data pointer.
Same as Data Pointer 1 High Byte Register, it is selected by DPSEL@DPS.
Same as Data Pointer 1 High Byte Register, it is selected by DPSEL@DPS.
Device ID Number = 12h.
Version Number = 00h
Bit7~1: Reserved Bit0: Select Data Pointer 1/2 Register (Default Value: 0) 1: Data Pointer 2 Register 0: Data Pointer 1 Register
6.1.1.12
All Interrupt Enable Register (INTEN) (Default Value: 0000_0000)
Bit7~1: Reserved Bit0: Enable 8051 All Interrupt Procedure 1: Enable 8051 All Interrupt Procedure 0: Disable
6.1.1.13
Memory Mapping Control Register (MMC) (Default Value: 0000_0000)
Bit7~1: Reserved Bit0: Enable Memory Mapping
1: Enable, 0000~07FFh (Address) based on Data Address Map to F800~FFFFh based on Code Address. 0: Disable
- 33 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.1.1.14 Chip Control 1 Register (CHIPCTRL1) (Default Value: 0000_0000)
Bit 7: Pulse Width Modulator 4 Function Enable 1: Enable Pulse Width Modulator 4 (GP27 GPIO Function Disable) 0: Power down Pulse Width Modulator 4 Bit 6: Pulse Width Modulator 3 Function Enable 1: Enable Pulse Width Modulator 3 (GP26 GPIO Function Disable) 0: Power down Pulse Width Modulator 3 Bit 5: Pulse Width Modulator 2 Function Enable 1: Enable Pulse Width Modulator 2 (GP25 GPIO Function Disable) 0: Power down Pulse Width Modulator 2 Bit 4: Pulse Width Modulator 1 Function Enable 1: Enable Pulse Width Modulator 1 (GP24 GPIO Function Disable) 0: Power down Pulse Width Modulator 1 Bit 3: UART Function Enable 1: Enable UART Block (GP42GP43 GPIO Function Disable) 0: Power down UART Block Bit 2: Advance LPC Function Enable 1: Enable CLKRUN# Function. (GP46 GPIO Function Disable) 0: Disable Bit 1~0: System Clock Select 00: Input Clock, 01: Input Clock, 10: Input Clock/2, 11: Input Clock/4
6.1.1.15
Chip Control 2 Register (CHIPCTRL2) (Default Value: 0000_0000)
Bit 7: D/A 2 Function Enable 1: Enable DAC2 Block (GP56 GPIO Function Disable) 0: Power down DAC2 Block Bit 6: D/A 1 Function Enable 1: Enable DAC1 Block (GP57 GPIO Function Disable) 0: Power down DAC1 Block Bit 5: A/D Function Enable 1: Enable ADC Block (GP6 GPIO Function Disable) 0: Power down ADC Block
- 34 -
W83L951DG/W83L951FG
Bit 4: Real Time Clock Function Enable 1: Enable RTC Block 0: Power down RTC Block Bit 3: Keyboard Scan Function Enable 1: Enable {GP0, GP1, GP20~23} Keyboard Scan Function and GP3 Key Wakeup Interrupt Function. 0: Disable
Note: To enable Keyboard Scan Function will switch {GP0, GP1, GP20~23} drive current from 12mA to 250uA.
Bit 2: Watch Dog Timer Function Enable 1: Enable WDT Block 0: Power down WDT Block Bit 1: Whole Chip Power down Enable 1: Power down mode: When there is no any external interrupt, Key Wake-up interrupt and LPC interrupt occurs or PS2 data line is low , W83L951DG/FG will stop external clock to enter power down mode, otherwise it will clear this bit as 0 automatically. 0: Normal Mode: When any external interrupt or Key Wake-up interrupt occurs or PS2 data line goes low, this bit will clear this bit as 0 automatically. Note: If whole chip power down mode and idle mode are both enabled, after leaving power down mode, W83L951DG/FG will enter idle mode to wait for internal interrupt. Bit 0: Whole Chip Idle Enable 1: Idle Mode: When there is no any interrupt occurs, W83L951DG/FG will enter idle mode, otherwise it will clear this bit as 0 automatically. 0: Normal Mode: It will clear this bit as 0 when all interrupt events occur.
6.1.1.16
Chip Control 3 Register (CHIPCTRL3) (Default Value: 0000_0000)
Bit 7: FAN 2 Function Enable 1: Enable FAN1 Block (GP40 GPIO Function Disable) 0: Power down FAN1 Block Bit 6: FAN 1 Function Enable 1: Enable FAN2 Block (GP41 GPIO Function Disable) 0: Power down FAN2 Block
- 35 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit 5: CIR Function Enable 1: Enable CIR Block (GP84 GPIO Function Disable) 0: Power down CIR Block Bit 4: Auxiliary PS2 Function Enable 1: Enable Auxiliary PS2 Block (GP70GP71 GPIO Function Disable) 0: Power down Auxiliary PS2 Block (The Wakeup by APS2 is also disabled) Bit 3: Mouse PS2 Function Enable 1: Enable Mouse PS2 Block (GP72GP73 GPIO Function Disable) 0: Power down Mouse PS2 Block (The Wakeup by MPS2 is also disabled) Bit 2: Keyboard PS2 Function Enable 1: Enable Keyboard PS2 Block (GP70GP71 GPIO Function Disable) 0: Power down Keyboard PS2 Block (The Wakeup by KPS2 is also disabled) Bit 1: SMBUS 2 Function Enable 1: Enable SMBUS2 Block (GP80GP81 GPIO Function Disable) 0: Power down SMBUS2 Block Bit 0: SMBUS 1 Function Enable 1: Enable SMBUS1 Block (GP76GP77 GPIO Function Disable) 0: Power down SMBUS1 Block
6.1.1.17
External Wake-up 1 Register (EXTWKP1) (Default Value: 0000_0000)
Bit7~4: Reserved Bit3: Enable Key Wake-up Interrupt wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Bit2: Enable External Interrupt 3 wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Bit1: Enable External Interrupt 2 wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Bit0: Enable External Interrupt 1 wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable.
- 36 -
W83L951DG/W83L951FG
6.1.1.18 External Wake-up 2 Register (EXTWKP2) (Default Value: 0000_0000)
Bit7~5: Reserved Bit4: Enable RTC Interrupt wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Bit3: Enable LPC Interrupt wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Bit2: Enable APS2 Interrupt wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Note: Before enabling the function, Auxiliary PS2 Noise Filter Enable Bit (NFEN@PS2CON) must be set low. Bit1: Enable MPS2 Interrupt wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Note: Before enabling the function, Mouse PS2 Noise Filter Enable Bit (NFEN@PS2CON) must be set low. Bit0: Enable KPS2 Interrupt wake-up W83L951DG/FG at power down mode. 1: Enable. 0: Disable. Note: Before enabling the function, Keyboard PS2 Noise Filter Enable Bit (NFEN@PS2CON) must be set low.
- 37 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.2 Low Pin Count Interface Block
LOW PIN COUNT INTERFACE(LPC) & SERIAL IRQ & DATA BUFFER BLOCK(10) INTA DDR NAME KBCCON LPCCON DBB0STS DBB0
DBB0ADDH DBB0ADDL
Table 6-7 Low Pin Count Interface Register Define
7 Reserved
DBB1En
6
5
4 P92EN
3 HKBEN
SIRQ01EN
2 HGAEN
SIRQ00EN
1 GA20SET
SIRQ1GEN
0 GA20CLR
SIRQ0GEN
91 92 93 94 95 96 97 99 9A 9B 9C 9D
DBB0En
SIRQ11EN
SIRQ10EN
UDF[3:0] Data Buffer 0 [7:0] Data Buffer 0 Address High Byte Data Buffer 0 Address Low Byte OBF01 SIRQ Number UDF[3:0] Data Buffer 1 [7:0] Data Buffer 1 Address High Byte Data Buffer 1 Address Low Byte OBF11 SIRQ Number
CD0
UDF
IBF0
OBF0
SIRQ0 DBB1STS DBB1
DBB1ADDH DBB1ADDL
OBF00 SIRQ Number CD1 UDF IBF1 OBF1
SIRQ1
OBF10 SIRQ Number
Gray: Only with System Reset to initial.
6.2.1 6.2.1.1
Register Description DBB0 Status Register (DBB0STS) (Default Value: 0000_?0?0)
Bit7~4: User Define Flag Bit3: Indicate IDBB0 Command/Data (By LRESET_N Pin to reset) 1: Command, 0: Data. Bit2: User Define Flag Bit1: Input Buffer Full Flag (By LRESET_N Pin to reset) 1: Full, 0: Empty Bit0: Output Buffer Full Flag 1: Full, 0: Empty
6.2.1.2
Data Bus Buffer 0 Register (DBB0) (Default Value: 0000_0000)
Write data to output buffer, and read data from input buffer.
- 38 -
W83L951DG/W83L951FG
6.2.1.3 Data Bus Buffer 0 Address High Byte Register (DBB0ADDH) (Default Value: 0000_0000)
DBB0 address is according to {DBB0ADDH, DBB0ADDL}. Default I/O address is 0x00h. If transmission is proceeding, address is encoded and decoded in next package.
6.2.1.4 Data Bus Buffer 0 Address Low Byte Register (DBB0ADDL) (Default Value: 0000_0000)
DBB0 address is according to {DBB0ADDH, DBB0ADDL}. Default I/O address is 0x00h. If transmission is proceeding, address is encoded and decoded in next package.
6.2.1.5
Low Pin Count Control Register (LPCCON) (Default Value: 0000_0000)
Bit7: Data Bus Buffer 1 Enable 1: Enable (If transmission is proceeding, address is encoded and decoded in next package.) 0: Disable Bit6: Data Bus Buffer 0 Enable 1: Enable (If transmission is proceeding, address is encoded and decoded in next package.) 0: Disable Bit5: Serial IRQ 11 Enable 1: Enable (Start generating Serial IRQ for OBF1) 0: Disable (Stop generating Serial IRQ for OBF1) Bit4: Serial IRQ 10 Enable 1: Enable (Start generating Serial IRQ for OBF1) 0: Disable (Stop generating Serial IRQ for OBF1) Bit3: Serial IRQ 01 Enable 1: Enable (Start generating Serial IRQ for OBF0) 0: Disable (Stop generating Serial IRQ for OBF0) Bit2: Serial IRQ 00 Enable 1: Enable (Start generating Serial IRQ for OBF0) 0: Disable (Stop generating Serial IRQ for OBF0) Bit1: Serial IRQ 1 Generate Start Bit W83L951DG/FG hardware checks this bit in every starting of Serial IRQ procedure. If this bit is high, W83L951DG/FG will generate Serial IRQ corresponding to OBF1 SIRQ Number @SIRQ. This bit clears as low automatically after W83L951DG/FG receives request and enters Serial IRQ procedure. This bit is set as high in writing this bit and data is written to Data Bus Buffer 1 Register. This bit is to provide the method to generate Serial IRQ that is needless through writing to Data Bus Buffer 1 Register.
- 39 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit0: Serial IRQ 0 Generate Start Bit W83L951DG/FG hardware checks this bit in every starting of Serial IRQ procedure. If this bit is high, W83L951DG/FG will generate Serial IRQ corresponding to OBF0 SIRQ Number @SIRQ. This bit clears as low automatically after W83L951DG/FG receives request and enters Serial IRQ procedure. This bit is set as high in writing this bit and data is written to Data Bus Buffer 0 Register. This bit is to provide the method to generate Serial IRQ that is needless through writing to Data Bus Buffer 0 Register.
6.2.1.6
Serial IRQ 0 Number (SIRQ0) (Default Value: 0000_0000)
Bit7~4: Serial IRQ 01 Number If transmission is proceeding, IRQ number will be changed in next transmission. Set as 0000, SIRQ01 is disabled. Bit3~0: Serial IRQ 00 Number If transmission is proceeding, IRQ number will be changed in next transmission. Set as 0000, SIRQ00 is disabled.
6.2.1.7
Serial IRQ 1 Number (SIRQ1) (Default Value: 0000_0000)
Bit7~4: Serial IRQ 11 Number If transmission is proceeding, IRQ number will be changed in next transmission. Set as 0000, SIRQ11 is disabled. Bit3~0: Serial IRQ 10 Number If transmission is proceeding, IRQ number will be changed in next transmission. Set as 0000, SIRQ10 is disabled.
6.2.1.8
Keyboard Control Register (KBCCON)(Default Value: 0000_0001)
Bit7~5: Serial IRQ Hold Counter for Serial IRQ Generate Function 000: Generate 1 cycle of Serial IRQ. 001: Generate 2 cycles of Serial IRQ. 010: Generate 3 cycles of Serial IRQ. 011: Generate 4 cycles of Serial IRQ. 100: Generate 5 cycles of Serial IRQ. 101: Generate 6 cycles of Serial IRQ. 110: Generate 7 cycles of Serial IRQ. 111: Generate 8 cycles of Serial IRQ.
- 40 -
W83L951DG/W83L951FG
Bit4: Port 92 Enable (Default Value: 0) 1: Enable W83L951DG/FG's hardware logic to receive the data written in I/O address@0092h. Bit1 and bit0 of port92 control register controls Gate A20 and KBRST pin. Gate A20 will drive high when bit1 is 1 and KBRESET pin drive {14us High 6us Low High} waveform when bit0 is 1. Gate A20 is default high level after LPC reset and GP44, GP45 GPIO function is disabled. 0: Disable Bit3: Hardware Keyboard Reset Control Enable (Default Value: 0) 1: Enable W83L951DG/FG's hardware logic to set KBRESET. When the KBC receives data that follows a "FE" command, the KBRESET pin drives {14us High 6us Low High} waveform. And GP44 GPIO function is disabled. 0: Disable Bit2: Hardware Gate A20 Control Enable (Default Value: 0) 1: Enable W83L951DG/FG's hardware logic to set Gate A20. When the KBC receives data that follows a "D1" command, the Gate A20 pin drives high. And GP45 GPIO function is disabled. 0: Disable Bit1: Gate A20 Set Set directly Gate A20 Output Register. If host is setting from LPC Interface, the request will be ignored. This belongs to software control. Bit0: Gate A20 Clear/Gate A20 Status Write: Clear directly Gate A20 Output Register. If host is setting from LPC Interface, the request will be ignored. This belongs to software control. Read: Current Internal Gate A20 Status.
6.2.1.9
DBB1 Status Register (DBB1STS) (Default Value: 0000_?0?0)
Bit7~4: User Define Flag Bit3: Indicate IDBB Command/Data (By LRESET# Pin to reset) 1: Command, 0: Data. Bit2: User Define Flag Bit1: Input Buffer Full Flag (By LRESET# Pin to reset) 1: Full, 0: Empty Bit0: Output Buffer Full Flag 1: Full, 0: Empty
- 41 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.2.1.10 Data Bus Buffer 1 Register (DBB1) (Default Value: 0000_0000)
The output buffer register and the input buffer register are located at the same address. The output buffer is write-only and the input buffer is read-only.
6.2.1.11 Data Bus Buffer 1 Address High Byte Register (DBB1ADDH) (Default Value: 0000_0000)
DBB1 address is according to {DBB1ADDH, DBB1ADDL}. Default I/O address is 0x00h. If transmission is proceeding, address will be encoded and decoded in next package, not in current package.
6.2.1.12 Data Bus Buffer 1 Address Low Byte Register (DBB1ADDL) (Default Value: 0000_0000)
DBB1 address is according to {DBB1ADDH, DBB1ADDL}. Default I/O address is 0x00h. If transmission is proceeding, address will be encoded and decoded in next package, not in current package.
- 42 -
W83L951DG/W83L951FG
6.3 Personal System 2 Block
The Winbond Keyboard controller has three independent PS/2 serial ports implemented in hardware, which are directly controlled by the on chip 8051. Each of the three PS/2 serial channels uses a synchronous serial protocol to communicate with the auxiliary device. Each PS/2 channel has two signal lines: Clock and Data. Both signal lines are bi-directional and employ open drain. The PS2DATA, PS2CON and PS2STS is defined individually for each PS/2 channel. PS2HSEN is only one register for controlling all PS/2 device handshake action. Table 6-8 Personal System 2(PS2) Register Define
KEYBOARD & MOUSE & AUXILIARY PS2 BLOCK(9) INTADDR
A1 A2 A3 A4 A5 A6 A7 A9 AA AB
NAME
KPS2CON KPS2STS
7
NFEN KPS2BUSY
6
Inhibit START_DEC
5
STOP
4
3
2
1
Reserved
0
KPS2T/R
KPS2DATA KPS2 Data register [7:0] PARITY PE
TTIMEOUT XMIT_BUSY FE
RTIMEOUT RDAT_RDY
MPS2DATA MPS2 Data register [7:0] MPS2CON MPS2STS PS2HSEN NFEN MPS2BUSY Reserved Inhibit START_DEC STOP PARITY PE Reserved MPS2T/R
TTIMEOUT XMIT_BUSY FE
RTIMEOUT RDAT_RDY HSEN
APS2DATA APS2 Data register [7:0] APS2CON APS2STS NFEN APS2BUSY Inhibit START_DEC STOP PARITY PE Reserved APS2T/R
TTIMEOUT XMIT_BUSY FE
RTIMEOUT RDAT_RDY
Gray: Only with System Reset to initial.
6.3.1 6.3.1.1
Register Description PS/2 Handshake Enable Register (PS2HSEN) (Default Value:: 0000_0000)
Bit 7~1: Reserved (always return `LOW') Bit 0: Handshake Mode Enable (HSEN) 0: The handshake mode of PS2 disables. 1: The handshake mode of PS2 enables. When the handshake mode of PS2 is enabling, the TR bit (BIT 0) of PSCON is automatically set high when the START_DEC bit (bit 6) of PS2STS of the other channel is set. Note: The priority of three PS2 interface is KPS2 > MPS2 > APS2. Whether the handshake mode of PS2 is enabling or no, the TR bit (BIT 0) of PSCON is automatically set high when the RDATA_RDY bit (bit 0) of PS2STS of this channel is set.
- 43 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.3.1.2
Transmit: The byte written to this register, when PS2_T/R = 1 and PS2_EN = 1 and XMIT_BUSY = 0, is transmitted automatically by the PS/2 channel control logic. On successful start of this transmission, the PS2 logic will automatic set XMIT_BUSY to high. If PS2_T/R = 0 or PS2_EN = 0 or XMIT_BUSY = 1, then writes to this register are ignored. On successful completion of this transmission or upon a Transmit Time-out condition the PS2_T/R and XMIT_BUSY bit is automatically set to low. The PS2_T/R bit must be written to a HIGH before initiating another transmission to the remote device. Note: Even if PS2_T/R = 1 and PS2_EN = 1 and XMIT_BUSY = 0, writing the transmit Register will hold the current transmission if RDATA_RDY is set. The automatic PS2 logic forces data to be read from the Receive Register before allowing a transmission. An interrupt is generated on the high to low transition of XMIT_BUSY. All bits of this register are write-only for transmit data, because you always read received data. Receive: When PS2_EN=1 and PS2_T/R=0, the PS2 Channel is set to automatically receive data on that channel (both the CLK and DATA lines will float waiting for the peripheral to initiate a reception by sending a start bit followed by the data bits). After a successful reception data is placed in this register and the RDATA_RDY bit is set and the CLK line is forced low by the PS2 channel logic. RDATA_RDY is cleared and the CLK line is released to hi-z following a read of this register. This automatically holds off further receive transfers until the 8051 has had a chance to get the data. Note: The Receive Register is initialized to 0xFF after a Timeout has occurred. The channel can be enabled to automatically transmit data (PS2_EN=1) by setting PS2_T/R while RDATA_RDY is set, however a device (not include host) transmission can hold until the data has been read from the Receive Register. An interrupt is generated on the low to high transition of RDATA_RDY. If a receive timeout (REC_TIMEOUT=1) or a transmit timeout (XMIT_TIMEOUT =1) occurs the channel is busied (CLK held low) for 300us(Input clock=24MHz) or 600us(Input clock=12MHz) (Hold Time) to guarantee that the peripheral aborts. Writing to the Transmit Register will be allowed; however the data written will not be transmitted until the Hold Time expires. In the foregoing situation, RDATA_RDY won't automatically clear.
PS/2 T/R DATA Registers (PS2DATA) (Default Value: 1111_1111)
- 44 -
W83L951DG/W83L951FG
6.3.1.3 PS/2 Control Registers (PS2CON) (Default Value:: 0000_0000)
Bit 7: NOISE FILTER ENABLE (NFEN) 0: Disable noise filter for clock line 1: Enable noise filter for clock line Bit 6: Inhibit bit The low to high transition of the inhibit bit will hold the clock line low for 100us(Input clock=24MHz) or 200us(Input clock=12MHz). Bit 5-4: STOP Bits [5:4] of the Control Register are used to set the level of the stop bit expected by the PS/2 channel state machine. These bits are therefore only valid when PS2_EN=1. Bits [5:4] = 00: Receiver expects an active high stop bit. 01: Receiver expects an active low stop bit. 10: Receiver ignores the level of the Stop bit (11th bit is not interpreted as a stop bit). 11: Reserved. Bit 3-2: PARITY Bits [3:2] of the Control Register are used to set the parity expected by the PS/2 channel state machine. These bits are therefore only valid when PS2_EN=1. Bits [3:2] = 00: Receiver expects Odd Parity (Default Value:). 01: Receiver expects Even Parity. 10: Receiver ignores level of the parity bit (10th bit is not interpreted as a parity bit). 11: Reserved. Bit 1: PS2_EN PS2 Channel Enable When PS2_EN=1 the PS/2 State machine is enabled allowing the channel to perform automatic reception or transmission depending on the bit value of PS2_T/R. When PS2_EN = 0, the channel's automatic PS/2 state machine is disabled. Note: If the PS2_EN bit is cleared prior to the rising edge of the 10th (parity bit) clock edge the receive data is discarded (RDATA_RDY remains low). If the PS2_EN bit is cleared following the rising edge of the 10th clock signal then the receive data is saved in the Receive Register (RDATA_RDY goes high) assuming no parity error. In the foregoing two situations, ps2 device can't differentiate host receive data success or fail, and therefore we don't recommend to use this function. It shall set to high before you start any operation of PS2.
- 45 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit 0: PS2_T/R PS/2 Channel Transmit/Receive This bit is only valid when PS2_EN=1 and sets the PS2 logic for automatic transmission or reception when PS2_T/R equals HIGH or LOW respectively (This bit may be modified, after unsetting PS2_EN). When set the PS/2 channel is enabled to transmit data. To properly initiate a transmit operation this bit must be set prior to writing to the Transmit Register; writes are blocked to the Transmit Register when this bit is not set. Upon setting the PS2_T/R bit the channel will drive its CLK line low and then float the DATA line and hold this state until a write occurs to the Transmit Register or until the PS2_T/R bit is cleared. Writing to the Transmit Register initiates the transmit operation. KB controller drives the data line low and, within 100us, floats the clock line (externally pulled high by the pull-up resistor) to signal to the external PS/2 device that data is now available. The PS2_T/R bit is cleared on the 11th clock edge of the transmission or if a Transmit Timeout error condition occurs. Note: If the PS2_T/R bit is set while the channel is actively receiving data prior to the rising edge of the 10th (parity bit) clock edge the receive data is discarded. If this bit is not set prior to the 10th clock signal then the receive data is saved in the Receive Register. When the PS2_T/R bit is cleared the PS/2 channel is enabled to receive data. Upon clearing this bit, whether RDATA_RDY=0 or no, the channel's CLK and DATA will float waiting for the external PS/2 device to signal the start of a transmission for receiving data. But if RDATA_RDY=1, the hardware won't generate interrupt to indicate finished receive data. If the PS2_T/R bit is set while RDATA_RDY=1 then the channel's DATA line will float but its CLK line will be held low, holding off the peripheral, until the Receive Register is read.
6.3.1.4
PS/2 Status Registers (PS2STS) (Default Value:: 0000_0000)
Bit 7: Receiver Busy (RX_BUSY) This bit is indicators for each of the three PS/2 Channels. When a RX_BUSY bit is set the associated channel is actively receiving PS/2 data; when a RX_BUSY bit is clear the channel is idle. Bit 6: Start Bit Detect (START_DEC) This bit is set on detecting start bit of receive conditions. Writing high will clear this bit. Bit 5: Transmitter Timeout (XMIT_TIMEOUT) This bit is set on one of 3 transmit conditions, and in addition the channel's CLK line is automatically pulled low and held for a period of 300us(Input clock=24MHz) or 600us(Input clock=12MHz) following assertion of the XMIT_TIMEOUT bit during which time the PS2_T/R is also held low: When the transmitter bit time (time between falling edges) exceeds 300us(Input clock=24MHz) or 600us(Input clock=12MHz). When the transmitter start bit is not received within 25ms(Input clock=24MHz) or 50ms(Input clock=12MHz) from signaling a transmit start event. If the time from the 1st (start, falling edge) bit to the 11th (stop, falling edge) bit exceeds 2ms. Writing high will clear this bit.
- 46 -
W83L951DG/W83L951FG
Bit 4: Transmitter Busy (XMIT_BUSY) When high, the XMIT_BUSY bit is a status bit indicating that the PS2 channel is actively transmitting data to the PS2 peripheral device. Writing to the Transmit Register whether the channel ready to transmit will cause the XMIT_BUSY bit to assert and remain asserted until one of the following conditions occur and an Interrupt is generated.. The falling edge of the 11th CLK; upon a Transmit Timeout condition (XMIT_TIMEOUT goes high); Upon the PS2_T/R bit being written to 0. Upon the PS2_EN bit being written to 0. Note: An interrupt is generated on the high to low transition of XMIT_BUSY. Bit 3: Framing Error (FE) When receiving data the stop bit is clocked in on the falling edge of the 11th CLK edge. If the channel has been set to expect either a high or low stop bit and the 11th bit is contrary to the expected stop polarity, then the FE and REC_TIMEOUT bits are set following the falling edge of the 11th CLK edge and an Interrupt is generated. Writing high will clear this bit. Bit 2: Parity Error (PE) When receiving data the parity bit is clocked in on the falling edge of the 10th CLK edge. If the channel has been set to expect either even or odd parity and the 10th bit is contrary to the expected parity, then the PE and REC_TIMEOUT bits are set following the falling edge of the 10th CLK edge and an Interrupt is generated. Writing high will clear this bit. Bit 1: Receiver Timeout (REC_TIMEOUT) Under PS2 automatic operation, PS2_EN=1, this bit is set on one of 4 receive error conditions, and in addition the Channel's CLK line is automatically pulled low and held for a period of 300us following assertion of the REC_TIMEOUT bit: When the receiver bit time (time between falling edges) exceeds 300us(Input clock=24MHz) or 600us(Input clock=12MHz). If the time from the 1st (start, falling edge) bit to the 10th (stop, falling edge) bit exceeds 2ms. On a receive parity error along with the parity error (PE) bit. On a receive framing error due to an incorrect STOP bit along with the framing error (FE) bit. Writing high will clear this bit. Note: An Interrupt is generated on the low to high transition of the REC_TIMEOUT bit. Bit 0: Data Ready (RDATA_RDY) Receive Data Ready: Under normal operating conditions, this bit is set following the falling edge of the 11th clock given successful reception of a data byte from the PS/2 peripheral (i.e., no parity, framing, or receive timeout errors) and indicates that the received data byte is available to be read from the Receive Register. This bit may also be set in the event that the PS2_EN bit is cleared following the 10th CLK edge (see the PS2_EN bit description for further details). Writing high will clear this bit. Note: An Interrupt is generated on the low to high transition of the RDATA_RDY bit.
- 47 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.4 System Management Bus Block
W83L951DG/FG provides 2 System Management Bus (SMBus) host controllers. The SMBus host controllers is SMBUS 2.0 compatible. It also provides 32 bytes FIFO. The FIFO contains SMBus1 Master Data FIFO(8), SMBus2 Master Data FIFO(8). Table 6-9 SMBus 1 Register Define
SMBUS 1 BLOCK(24) INTADDR B1 B2 B3 B4 B5 B6 B7 B9 BA BB BC BD NAME SM1SCR SM1IREQ SM1IE 7 Reserved MSTS 6 5 Baud Rate Select MFIFORdy MFIFOReq MPktFinish 4 3 2 RBIM 1 0
Reserved Reserved
Interrupt Enable [7:0] RepStart Master Level[1:0] ClrMFIFO ClrSFIFO Slave Leve[1:0]
SM1FIFOCON STOP SM1MFIFO SM1MCON SM1MSTS
Master Data FIFO [7:0] MasterEn RMS RxTMO TxTMO Empty Read Byte Count[5:0] AlFull AlEmty WrErr NACKRe ArbFail ClrFinish
SM1MFIFOSTS Full Reserved Reserved Reserved Reserved
FIFO Data Length[5:0]
Table 6-10 SMBus 2 Register Define
SMBUS 2 BLOCK(24) INTADDR C1 C2 C3 C4 C5 C6 C7 C9 CA CB CC CD NAME SM2SCR SM2IREQ SM2IE SM2FIFOCON SM2MFIFO SM2MCON SM2MSTS SM2MFIFOSTS Reserved Reserved Reserved Reserved MasterEn RxTMO Full RMS TxTMO Empty AlFull AlEmty STOP RepStart 7 Reserved MSI 6 5 4 Baud Rate Select 3 2 RBIM 1 Reserved 0 Reserved
MFIFORdy MFIFOReq MPktFinish Interrupt Enable [7:0] Master Level[1:0] ClrMFIFO ClrSFIFO Slave Leve[1:0]
Master Data FIFO [7:0] Read Byte Count[5:0] WrErr NACKRec ArbFail ClrFinish
FIFO Data Length[5:0]
Gray: Only with System Reset to initial.
- 48 -
W83L951DG/W83L951FG
6.4.1 6.4.1.1 Register Description System Control Register (SM1/2SCR) (Default Value: 0001_10?0)
Bit 7~6: Reserved (Must Assign Low) Bit 5~3: Baud Rate Select Select SMBus baud rate. Input Clock is 24MHz : When System Clock is 24MHz: 000: 12.5 KHz, 001: 25 KHz, 010: 50 KHz, 011: 100 KHz 100: 400 KHz, 101: 800 KHz, 110: 1.2 MHz, 111: 2.4 MHz When System Clock is 12MHz: 000: 12.5 KHz, 001: 25 KHz, 010: 50 KHz, 011: 100 KHz 100: 400 KHz, 101: 800 KHz, 110: 1.2 MHz, 111: N/A When System Clock is 6MHz: 000: 12.5 KHz, 001: 25 KHz, 010: 50 KHz, 011: 100 KHz 100: 400 KHz, 101: 800 KHz, 110: N/A, 111: N/A
Input Clock is 12MHz When System Clock is 12MHz: 000: 6.25 KHz, 001: 12.5 KHz, 010: 25 KHz, 011: 50 KHz 100: 200 KHz, 101: 400 KHz, 110: 600 KHz, 111: 1.2 MHz When System Clock is 6MHz: 000: 6.25 KHz, 001: 12.5 KHz, 010: 25 KHz, 011: 50 KHz 100: 200 KHz, 101: 400 KHz, 110: 600 KHz, 111: N/A When System Clock is 3MHz: 000: 6.25 KHz, 001: 12.5 KHz, 010: 25 KHz, 011: 50 KHz 100: 200 KHz, 101: 400 KHz, 110: N/A, 111: N/A Bit 2: Rx Byte Interrupt Mode Select the mode that SMBus receive data bytes to generate Master/Slave Data Ready interrupt. 0: Only First Byte and FIFO Full Byte: Master/Slave Data Ready Interrupt only occurs in receiving first byte after Start phase or Repeat_Start phase and any byte that make FIFO enter Full state. 1: Every Byte: Master/Slave Data Ready Interrupt occurs in every time to finish receiving one byte.
- 49 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit 1: SMBALERT Pin Status (Reserved) Bit 0: SMBALTER Event Control (Reserved) Control the occurrence of SMBALTER Event 0: Disable 1: Enable.
6.4.1.2
Interrupt Register (SM1/2IREQ) (Default Value: 0000_0000)
Bit 7: Master Status Indicate Master Status Register changed. Bit 6: Master FIFO Data Ready Interrupt Indicate that FIFO finishes receiving data byte when Master is under MSR (Master at Receiving) mode. About detail description, please refer Bit7@SM1/2SCR. Bit 5: Master FIFO Data Request Interrupt Indicate that FIFO request micro-processor provides data for transmitting to Salve when Master is under MST (Master at Transmitting) mode and empty. Bit 4: Master Packet Finished Interrupt Indicate that Master finishes package transmission (Include Rx and Tx). Bit 3~0: Reserved
6.4.1.3
All Bits:
Interrupt Enable Register (SM1/2IE) (Default Value: 0000_0000)
1: Enable Interrupt. The content of Interrupt Register via OR operation will convert into Microprocessor Internal Interrupt Source. 0: Disable Interrupt. Disable convert into Microprocessor Internal Interrupt, but relative interrupt flag will still be produced.
6.4.1.4
FIFO Control Register (SM1/2FIFOCON) (Default Value: 0000_0000)
Bit 7: STOP Tag Flag (Only for Master) Indicate that writing byte is the last byte. Bit 6: Repeat_Start Tag Flag (Only for Master) Indicate that writing byte is Repeat_Start Byte. Bit 5~4: Master FIFO Threshold Level Select 00: AE - 2, AF - 6, 01: AE - 3, AF - 5 10: AE - 4, AF - 4, 11: Disable Note: AE is Almost Empty Flag, AF is Almost Full Flag.
- 50 -
W83L951DG/W83L951FG
Bit 3: Clear Master FIFO Clear Master FIFO. Master will stop transfer immediately and generate Stop phase. After SMBus finishes the action, SMBus responds to micro-processor via FIFO Clear Finished Event in Master Status Register. Bit 2~0: Reserved
6.4.1.5
Master Data FIFO Register (SM1/2MFIFO) (Default Value: 0000_0000)
This FIFO register stores the data from Master. Only allow writing in MST mode, and only allowed to read in MSR mode. Default is MST mode and transforming is through Data_Ready_Interrupt.
6.4.1.6
Master Control Register (SM1/2MCON) (Default Value: 0100_0000)
Bit 7: Master Enable Bit 6: Read Mode Select 1: Host Read One Byte Hold Mode. Master holds bus (drive SCL low) after finishing receiving every byte. 0: Host Read Continue Mode. Master finishes {Receiving Package -> Stop Phase -> Release Bus} automatically according to read byte count. Note: If Read Byte Count initial value is 1, Master will ignore criterion of "Host Read One Byte Hold Mode". Bit 5~0: Read Byte Count Indicate Read Byte Count. The allowed maximum is 64 bytes block read. Filled Value Actual Value 0 64 1~63 1~63
6.4.1.7
Master Status Register (SM1/2MSTS) (Default Value: 0000_0000)
Bit 7: Master Rx Timeout Event Indicate Master generates RX_TIMEOUT (When Master FIFO is full, SCL drive low to generate timeout). After the Master generates Stop Phase, will be back to initial state and clear FIFO. Note: If timeout is not generated by the Master, the response will occur in FIFO Clear Finished Event in Master Status Register. Bit 6: Master Tx Timeout Event Indicate Master generates TX_TIMEOUT (When Master FIFO is empty, SCL drive low to timeout). After Master generates Stop Phase, will be back to initial state and clear FIFO. generate
Note: If timeout is not generated by Master, the response is in FIFO Clear Finished Event in Master Status Register.
- 51 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit 5: Master Almost Full Event Indicate that Master generate Almost Full Event. It occurs only up to Almost Full level. Bit 4: Master Almost Empty Event Indicate that Master generate Almost Empty Event. It occurs only down to Almost Empty level. Bit 3: Master FIFO Data Write Error Event Indicate that Microprocessor writes to Master FIFO, Master FIFO is full or Read Mode. Bit 2: NACK Received Event Indicate that Master receives NACK. After generating Stop Phase, Master will be back to initial state and clear FIFO. Note: Wait for the response of Clear Finished Event in Master Status Register to start next transfer. Bit 1: Bus Arbitration Failed Event Indicate that bus arbitration failed. Master will be back to initial state and clear FIFO. Bit 0: FIFO Clear Finished Event Indicate that Master finishes the request to clear FIFO. Note: When Micro Processors has not proposed Master FIFO Clear Request but produces, it indicates the remote device to drive SCL low to generate timeout.
6.4.1.8
Master FIFO Status Register (SM1/2MFIFOSTS) (Default Value: 0100_0000)
Bit 7: Full Flag Bit 6: Empty Flag Bit 5~4: Reserved Bit 3~0: FIFO Data Length
- 52 -
W83L951DG/W83L951FG
6.5 Internal Interrupt Controller Block
W83L951DG/FG Interrupts occur by 28 sources, 27 external and 25 internal interrupt. About Interrupt Control, each interrupt is controlled and corresponding to a bit in Interrupt Enable Register (IE1/2/3/4), the Interrupt Priority Control Register (IP1/2/3/4) and the Interrupt Request Register (IREQ1/2/3/4). An interrupt occurs if the corresponding Interrupt Request occurs and enable bits is HIGH. When several interrupts occur at the same time, the interrupts are received according to priority setting. If interrupts are setting to same priority, then it is decided by hardware internal checking rule. After Interrupt of EXTINT1, EXTINT2, EXTINT3, SMBUS1, SMBUS2, FAN1 and FAN2 is produced, can't be interrupt by other Interrupt source, so should set as High Propriety. Table 6-11 Internal Interrupt Controller Register Define
INTERRUPT BLOCK(17) INTADDR NAME 7 6 5 4 3 2 1 0
E1 E2 E3 E4 E9 EA EB EC F1 F2 F3 F4
IE1 IE2 IE3 IE4 IREQ1 IREQ2 IREQ3 IREQ4 IPRO1 IPRO2 IPRO3 IPRO4
TimerY CNTR1 FAN2 R TimerY CNTR1 FAN2 R TimerY CNTR1 FAN2 R
TimerX CNTR0 FAN1 R TimerX CNTR0 FAN1 R TimerX CNTR0 FAN1 R
Timer2 ADC CIR R Timer2 ADC CIR R Timer2 ADC CIR R
Timer1 RTC APS2 R Timer1 RTC APS2 R Timer1 RTC APS2 R
OBE1 KEYWP MPS2 R OBE1 KEYWP MPS2 R OBE1 KEYWP MPS2 R
IBF1 EXINT3 KPS2 R IBF1 EXINT3 KPS2 R IBF1 EXINT3 KPS2 R
OBE0 EXTINT2 SMBUS2 UARTRX OBE0 EXTINT2 SMBUS2 UARTRX OBE0 EXTINT2 SMBUS2 UARTRX
IBF0 EXTINT1 SMBUS1 UARTTX IBF0 EXTINT1 SMBUS1 UARTTX IBF0 EXTINT1 SMBUS1 UARTTX
- 53 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Table 6-12 Internal Interrupt Vector & Trigger Type Table
SOURCE VECTOR ADDRESS TRIGGER TYPE
Non-mask Interrupt LPC Power Fail Interrupt Input Buffer 0 Full Interrupt Output Buffer 0 Empty Interrupt Input Buffer 1 Full Interrupt Output Buffer 1 Empty Interrupt Timer 1 Interrupt Timer 2 Interrupt Timer X Interrupt Timer Y Interrupt External Interrupt Group 1 External Interrupt Group 2 External Interrupt Group 3 Key Interrupt Real Time Clock Alarm Interrupt ADC Interrupt CNTR0 Interrupt CNTR1 Interrupt SMBUS 1 Interrupt SMBUS 2 Interrupt Keyboard PS2 Interrupt Mouse PS2 Interrupt Auxiliary PS2 Interrupt CIR Interrupt FAN 1 Interrupt FAN 2 Interrupt UART Tx Interrupt UART Rx Interrupt Reserved Reserved Reserved Reserved
0x0003 0x000b 0x0013 0x001b 0x0023 0x002b 0x0033 0x003b 0x0043 0x004b 0x0053 0x005b 0x0063 0x006b 0x0073 0x007b 0x0083 0x008b 0x0093 0x009b 0x00a3 0x00ab 0x00b3 0x00bb 0x00c3 0x00cb 0x00d3 0x00db 0x00e3 0x00eb 0x00f3 0x00fb
Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Level Trigger Level Trigger Level Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Level Trigger Level Trigger Edge Trigger Edge Trigger Edge Trigger Edge Trigger Level Trigger Level Trigger Edge Trigger Edge Trigger N/A N/A N/A N/A
6.5.1 6.5.1.1
Register Description Interrupt Enable 1 Register (IE1) (Default Value: 0000_0000)
1: Enable. It produces Interrupt Request to Micro-Processor that Interrupt will be produced, and write down in Interrupt Request 1 Register. 0: Disable. It does not produce Interrupt Request to Micro-Processor that Interrupt will be produced, but write down in Interrupt Request 1 Register.
6.5.1.2
Interrupt Enable 2 Register (IE2) (Default Value: 0000_0000)
1: Enable. It produces Interrupt Request to Micro-Processor that Interrupt will be produced, and write down in Interrupt Request 2 Register. - 54 -
W83L951DG/W83L951FG
0: Disable. It does not produce Interrupt Request to Micro-Processor that Interrupt will be produced, but write down in Interrupt Request 2 Register.
6.5.1.3
Interrupt Enable 3 Register (IE3) (Default Value: 0000_0000)
1: Enable. It produces Interrupt Request to Micro-Processor that Interrupt will be produced, and write down in Interrupt Request 3 Register. 0: Disable. It does not produce Interrupt Request to Micro-Processor that Interrupt will be produced, but write down in Interrupt Request 3 Register.
6.5.1.4
Interrupt Enable 4 Register (IE4) (Default Value: 0000_0000)
1: Enable. It produces Interrupt Request to Micro-Processor that Interrupt will be produced, and write down in Interrupt Request 4 Register. 0: Disable. It does not produce Interrupt Request to Micro-Processor that Interrupt will be produced, but write down in Interrupt Request 4 Register.
6.5.1.5
Read:
Interrupt Request 1 Register (IREQ1) (Default Value: 0000_0000)
1: Requested 0: No Requested
Write:
1: Clear 0: No Change 6.5.1.6
Read:
Interrupt Request 2 Register (IREQ2) (Default Value: 0000_0000)
1: Requested 0: No Requested
Write:
1: Clear 0: No Change
- 55 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.5.1.7
Read:
Interrupt Request 3 Register (IREQ3) (Default Value: 0000_0000)
1: Requested 0: No Requested
Write:
1: Clear 0: No Change 6.5.1.8
Read:
Interrupt Request 4 Register (IREQ4) (Default Value: 0000_0000)
1: Requested 0: No Requested
Write:
1: Clear 0: No Change 6.5.1.9 Interrupt Priority 1 Register (IPRO1) (Default Value: 0000_0000)
1: High Priority 0: Low Priority 6.5.1.10 Interrupt Priority 2 Register (IPRO2) (Default Value: 0000_0000)
1: High Priority 0: Low Priority 6.5.1.11 Interrupt Priority 3 Register (IPRO3) (Default Value: 0000_0000)
1: High Priority 0: Low Priority 6.5.1.12 Interrupt Priority 4 Register (IPRO4) (Default Value: 0000_0000)
1: High Priority 0: Low Priority
- 56 -
W83L951DG/W83L951FG
6.6 GPIOs Block
W83L951DG/FG provides 13 GPIO blocks, and every GPIO block has 8 GPIO that can set individually. I/O Pad has three states by data register and direction register setting. Input register always reads current pad status.
Figure 6-1 GPIO Block Diagram Table 6-13 GPIOs Type Setup Define
TYPE OUTPUT REGISTER(WRITE) DIRECTION REGISTER
Input Output Open-Drain
Don't Care Output Data 0
0 1 Output Data'
Table 6-14.GPIOs Control Register Define
GPIO BLOCK(26) INTADDR NAME 7 6 5 4 3 2 1 0
80 88 90 98 A0 A8 B0 B8 C0 C8 D8 E8 F8
GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8 GPIO9 GPIOA GPIOB GPIOC
GPIO 0 Input/Output Register[7:0] GPIO 1 Input/Output Register[7:0] GPIO 2 Input/Output Register[7:0] GPIO 3 Input/Output Register[7:0] GPIO 4 Input/Output Register[7:0] GPIO 5 Input/Output Register[7:0] GPIO 6 Input/Output Register[7:0] GPIO 7 Input/Output Register[7:0] GPIO 8 Input/Output Register[7:0] GPIO 9 Input/Output Register[7:0] GPIO A Input/Output Register[7:0] GPIO B Input/Output Register[7:0] GPIO C Input/Output Register[7:0]
- 57 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Continued.
GPIO BLOCK(26) INTADDR NAME 7 6 5 4 3 2 1 0
D1 D2 D3 D4 D5 D6 D7 D9 DA DB DC DD DE
GPIOD0 GPIOD1 GPIOD2 GPIOD3 GPIOD4 GPIOD5 GPIOD6 GPIOD7 GPIOD8 GPIOD9 GPIODA GPIODB GPIODC
GPIO 0 Direction Register[7:0] GPIO 1 Direction Register[7:0] GPIO 2 Direction Register[7:0] GPIO 3 Direction Register[7:0] GPIO 4 Direction Register[7:0] GPIO 5 Direction Register[7:0] GPIO 6 Direction Register[7:0] GPIO 7 Direction Register[7:0] GPIO 8 Direction Register[7:0] GPIO 9 Direction Register[7:0] GPIO A Direction Register[7:0] GPIO B Direction Register[7:0] GPIO C Direction Register[7:0]
6.6.1 6.6.1.1
Write:
GPIO Data Register Description GPIO 0 Input/Output Register (GPIO0) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result. For example "CPL Bit" Instruction Read Pin Status into temp Register. Invert temp register. Write Result to Output Data Register according for bit address, and not influence the value of other
bit.
6.6.1.2
Write: Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
GPIO 1 Input/Output Register (GPIO1) (Default Value: 0000_0000)
- 58 -
W83L951DG/W83L951FG
6.6.1.3
Write: Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
GPIO 2 Input/Output Register (GPIO2) (Default Value: 0000_0000)
6.6.1.4
Write:
GPIO 3 Input/Output Register (GPIO3) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
6.6.1.5
Write:
GPIO 4 Input/Output Register (GPIO4) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
6.6.1.6
Write:
GPIO 5 Input/Output Register (GPIO5) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
6.6.1.7
Write:
GPIO 6 Input/Output Register (GPIO6) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
- 59 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.6.1.8
Write: Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
GPIO 7 Input/Output Register (GPIO7) (Default Value: 0000_0000)
6.6.1.9
Write:
GPIO 8 Input/Output Register (GPIO8) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
6.6.1.10
Write:
GPIO 9 Input/Output Register (GPIO9) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
6.6.1.11
Write:
GPIO A Input/Output Register (GPIOA) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
6.6.1.12
Write:
GPIO B Input/Output Register (GPIOB) (Default Value: 0000_0000)
Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
- 60 -
W83L951DG/W83L951FG
6.6.1.13
Write: Output data register Read: GPIO pin status whether GPIO function is active or not. Note: bit command and byte command have same result
GPIO C Input/Output Register (GPIOC) (Default Value: 0000_0000)
6.6.2 6.6.2.1
GPIO Direction Register Description GPIO 0 Direction Register (GPIOD0) (Default Value: 0000_0000)
1: Output, 0: Input.
6.6.2.2
1: Output, 0: Input.
GPIO 1 Direction Register (GPIOD1) (Default Value: 0000_0000)
6.6.2.3
1: Output, 0: Input.
GPIO 2 Direction Register (GPIOD2) (Default Value: 0000_0000)
6.6.2.4
1: Output, 0: Input.
GPIO 3 Direction Register (GPIOD3) (Default Value: 0000_0000)
6.6.2.5
1: Output, 0: Input.
GPIO 4 Direction Register (GPIOD4) (Default Value: 0000_0000)
6.6.2.6
1: Output, 0: Input.
GPIO 5 Direction Register (GPIOD5) (Default Value: 0000_0000)
6.6.2.7
1: Output, 0: Input.
GPIO 6 Direction Register (GPIOD6) (Default Value: 0000_0000)
- 61 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.6.2.8
1: Output, 0: Input.
GPIO 7 Direction Register (GPIOD7) (Default Value: 0000_0000)
6.6.2.9
1: Output, 0: Input.
GPIO 8 Direction Register (GPIOD8) (Default Value: 0000_0000)
6.6.2.10
1: Output, 0: Input.
GPIO 9 Direction Register (GPIOD9) (Default Value: 0000_0000)
6.6.2.11
1: Output, 0: Input.
GPIO A Direction Register (GPIODA) (Default Value: 0000_0000)
6.6.2.12
1: Output, 0: Input.
GPIO B Direction Register (GPIODB) (Default Value: 0000_0000)
6.6.2.13
1: Output, 0: Input.
GPIO C Direction Register (GPIODC) (Default Value: 0000_0000)
- 62 -
W83L951DG/W83L951FG
6.7 Watch Dog Block
The watchdog timer gives a mean of returning to the reset state when a program cannot run on a normal loop (for example, because of a software run-away). The watchdog timer consists of an 8-bit timer L and an 8-bit timer H. At reset or writing to the watchdog timer control register WDTCON [7] (START), each watchdog timer H and L is set to 0FFh. About Watchdog timer H count size selection, we can use Bit 5 of the watchdog timer control register (SIZE) permits selecting a watchdog timer H count source. When this bit is set to LOW, the count source becomes the underflow signal of watchdog timer L. Table 6-15.Watch Dog Register Define
WATCH DOG BLOCK(1) EXTADDR NAME 7 6 5 4 3 2 1 0
00 01
WDTCON WDTSTS
START Reserved
INTTYPE
SIZE
Clock Prescale Number[4:0] +WDT
Gray: Only with System Reset (Pin Reset + WDT Reset) to Initial. +: Only with Pin Reset to Initial
6.7.1 6.7.1.1
Register Description Watch Dog Control Register (WDTCON) (Default Value: 0000_0000)
Reset with Power Reset & Pin Reset.
Bit 7: Start 1: Start / Reload 0: Stop This Bit permits enable/disable the watchdog timer. Write LOW to this bit, the watchdog timer is stopped. Write HIGH to this bit will reload the watchdog timer (watchdog timer H and L is set to 0FFh) even this bit is already be HIGH. After written HIGH, the watchdog timer is running. Once this timer is timed-out the chip is reset. Also the watchdog timer is stopped to prevent the next time-out. Bit 6: Interrupt Type 1: NMI 0: Hardware reset Bit 5: Size Select the counter size. The counter starts from low to overflow. Then generate interrupt or hardware reset. 1: One Byte Counter. WDT Timeout Limit 256 Count Frequency . 0: Two Byte Counter. WDT Timeout Limit 65536 Count Frequency .
- 63 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit 4~0: Clock Prescale Number Input clock=24MHz : Count frequency is 1MHz / 2(Clock Prescale Number +1). Input clock=12MHz : Count frequency is 1MHz / 4(Clock Prescale Number +1).
6.7.1.2
Watch Dog Status Register (WDTSTS) (Default Value: 0000_0000)
Reset with Power Reset.
Bit 7~1: Reserved Bit 0: WDT Reset Finished 1: Finished, 0: No Happened.
- 64 -
W83L951DG/W83L951FG
6.8 Timer Block
The Keyboard controller has four timers: timer X, timer Y, timer 1, and timer 2. The division ratio of each timer or pre-scalar is given by 1/n + 1, where n is the value in the corresponding timer or prescalar latch. All timers are count down. When the timer reaches "00H", an underflow occurs at the next count pulse and the corresponding timer latch is reloaded into the timer and the count is continued. When a timer is underflow, the corresponding interrupt request bit is set to 1. In Timer 1 and Timer 2, the count source of pre-scalar 1/2 is the oscillator frequency divided by 16. The output of pre-scalar 1/2 is counted for both timer 1 and 2, and a timer underflow sets the interrupt request bit. Timer X and Timer Y can works in one of four operating modes by setting the timer XY mode register. Table 6-16.Timer Register Define
TIMER BLOCK(9) EXTADDR NAME 7 6 5 4 3 2 1 0
10 11 12 13 18 19 1A 1B 1C
PRE1 T1 PRE2 T2 TM PREX TX PREY TY
TM1ST TM2ST TMYST
Prescale 1 [6:0] Prescale 2 [6:0] CNTR1 TMYMODE TMXST CNTR0 TMXMODE
Timer 1 [7:0] Timer 2 [7:0] Prescale X [7:0] Timer X[7:0] Prescale Y [7:0] Timer Y [7:0]
6.8.1 6.8.1.1
Register Description Clock Prescale Number of Timer 1 (PRE1) (Default Value: 0111_1111)
Bit 7: Timer 1 Start Bit Write: Start Timer 1 counter. 1: Enable (Prescale Counter Reload & Start, but Timer 1 Data Keep) 0: Disable Read: Always Read `LOW'.
- 65 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Bit 6~0: Clock Prescale Number Write: Prescale Counter Reload. Read: Current Prescale Counter Value
6.8.1.2
Bit 7~0:
Timer 1 Register (T1) (Default Value: 1111_1111)
Write: Timer 1 Counter Reload. Read: Current Timer 1 Counter Value Note: In writing, due to the effect of internal frequency XIN/16, 0~16 system clock error occurs in first prescale period width.
6.8.1.3
Clock Prescale Number of Timer 2 (PRE2) (Default Value: 0111_1111)
Bit 7: Timer 2 Start Bit 1: Start (Prescale Counter Reload & Start, but Timer 2 Data Keep) 0: Stop Bit 6~0: Clock Prescale Number Write: Prescale Counter Reload.
6.8.1.4
Bit 7~0:
Timer 2 Register (T2) (Default Value: 1111_1111)
Write: Timer 2 Reload. Note: In writing, due to the effect of internal frequency XIN/16, 0~16 system clock error occurs in first prescale period width.
6.8.1.5
Timer X/Y Mode Register (TM) (Default Value: 0000_0000)
Bit 7: Timer Y Start Bit Start internal Time Y counter and 1: Enable (Prescale Y & Timer Y Data Keep after Stop) 0: Disable Bit 6: CNTR1 active edge selection bit 0: Interrupt at falling edge Count at rising edge in event counter mode. 1: Interrupt at rising edge Count at falling edge in event counter mode. Bit 5-4: Timer Y operating bit 00: Timer mode The Timer Y can select the count by XIN/16. 01: Pulse output mode (Disable GP83 Function, Pin Direct Force "Output") Timer Y counts XIN/16. Whenever the contents of the timer reach "00H", the signal output from the CNTR1 pin is inverted. If the CNTR1 active edge selection bit is 0, the pin is "H" after initial. If it is 1, the pin is `L' after initial. When using a timer in this mode, set the corresponding direction register of port GP83 to output mode. 10: Event count mode (Disable GP83 Function, Pin Direct Force "Input") - 66 -
W83L951DG/W83L951FG
Operating on event counter mode is the almost same as in timer mode, except that the timer counts signals input through the CNTR1. When the CNTR1 active edge selection bit is 0, the rising edge on the CNTR1 pin is counted. When the CNTR1 active edge selection bit is 1, the falling edge on the CNTR1 pin is counted. 11: Pulse width measurement mode (Disable GP83 Function, Direct Force "Input") If the CNTR1 active edge selection bit is 0, the timer counts XlN/16 while the CNTR1 pin is H. If the CNTR1 active edge selection bit is 1, the timer counts while the CNTR1 pin is `L'. Bit 3: Timer X Start Bit 1: Enable (Prescale X & Timer X Data Keep) 0: Disable Bit 2: CNTR0 active edge selection bit 0: Interrupt at falling edge Count at rising edge in event counter mode. 1: Interrupt at rising edge Count at falling edge in event counter mode. Bit 1-0: Timer X operating bit 00: Timer mode The Timer X only counts XIN/16. 01: Pulse output mode (Disable GP82 Function, Direct Force "Output") Timer X counts XIN/16. Whenever the contents of the timer reach "00H", the signal output from the CNTR0 pin is inverted. If the CNTR0 active edge selection bit is 0, the pin is "H" after initial. If it is 1, the pin is `L' after initial. When using a timer in this mode, set the corresponding direction register of port GP82 to output mode. 10: Event count mode (Disable GP82 Function, Direct Force "Input") Operating on event counter mode is the almost same as in timer mode, except that the timer counts signals input through the CNTR0. When the CNTR0 active edge selection bit is 0, the rising edge on the CNTR0 pin is counted. When the CNTR0 active edge selection bit is 1, the falling edge on the CNTR0 pin is counted. 11: Pulse width measurement mode (Disable GP82 Function, Direct Force "Input") If the CNTR0 active edge selection bit is 0, the timer counts XlN/16 while the CNTR0 pin is H. If the CNTR0 active edge selection bit is 1, the timer counts while the CNTR0 pin is `L'. Note: The count can be stopped by setting a "0" to the timer X (or timer Y) count start bit in any mode. The corresponding interrupt request bit is set each time a timer underflows.
6.8.1.6
Clock Prescale Number of Timer X (PREX) (Default Value: 1111_1111)
Bit 7~0: Clock Prescale Number Write: Prescale Counter Reload. Read: Current Prescale Counter Value Note: In writing, due to the effect of internal frequency XIN/16, 0~16 system clock error occurs in first prescale period width.
- 67 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.8.1.7
Bit 7~0: Write: Timer X Reload. Read: Current Timer X Counter Value Note: In writing, due to the effect of internal frequency XIN/16, 0~16 system clock error occurs in first prescale period width.
Timer X Register (TX) (Default Value: 1111_1111)
6.8.1.8
Clock Prescale Number of Timer Y (PREY) (Default Value: 1111_1111)
Bit 7~0: Clock Prescale Number Write: Prescale Counter Reload. Note: In writing, due to the effect of internal frequency XIN/16, 0~16 system clock error occurs in first prescale period width. Read: Current Prescale Counter Value
6.8.1.9
Bit 7~0:
Timer Y Register (TY) (Default Value: 1111_1111)
Write: Timer Y Reload. Read: Current Timer X Counter Value
- 68 -
W83L951DG/W83L951FG
6.9 Pulse Width Modulator Block
W83L 951D provides 4 Pulse Width Modulator Output. 8-bit PWM has two: PWM1 and PWM2. The fixed resolution is about 64us(Input clock=24MHz) or 128us(Input clock=12MHz). 16-bit PWM has two: PWM3 and PWM4. The minimum resolution can be selected by frequency select in PWM Control Register. Table 6-17.Pulse Width Modulator Register Define
PULSE WIDTH MEASURER BLOCK(13) EXTADDR NAME 7 6 5 4 3 2 1 0
20 21 22 23 24 25 26 27 28 29 2A 2B 2C
PWMCON PWM1P PWM1H PWM2P PWM2H PWM3PL PWM3PH PWM3HL PWM3HH PWM4PL PWM4PH PWM4HL PWM4HH
Reserved
PWM4 Freq. Select
Reserved
PWM3 Freq. Select
PWM 1 Period Register [7:0] PWM 1 High Level Register [7:0] PWM 2 Period Register [7:0] PWM 2 High Level Register [7:0] PWM 3 Period Register [7:0] PWM 3 Period Register [15:8] PWM 3 High Level Register [7:0] PWM 3 High Level Register [15:8] PWM 4 Period Register [7:0] PWM 4 Period Register [15:8] PWM 4 High Level Register [7:0] PWM 4 High Level Register [15:8]
Gray: Only with System Reset to initial. Note: If {PWM High Level Register} = 0, the output keeps in low level. If {PWM High Level Register} >= {PWM Period Register} ,the PWM1/PWM2 output will keep in high level with 1us low pulse , PWM3/PWM4 output will keep in high level without pulse. If PWM1/PWM2 is {PWM Period Level Register} > {PWM High Level Register} >0, then Period Width: 64 x {PWM Period Level Register} + 4units. Low Width : 64 x ({PWM Period Level Register} {PWM High Level Register}) 1unit. High Width : 64 x {PWM High Level Register} 3 units. Publication Release Date: August 2006 Revision 1.0
- 69 -
W83L951DG/W83L951FG
The unit is 1us in PWM1/PWM2. PWM 3/PWM4 is {PWM Period Level Register} > {PWM High Level Register} >0, then Period Width: {PWM Period Level Register} + 4units. Low Width : {PWM Period Level Register} {PWM High Level Register} 1unit. High Width : {PWM High Level Register} 3units. The unit is 1/F in PWM 3/PWM4. And F is defined in PWM Control Register. PWM 1/PWM2/PWM3/PWM4 is default low.
6.9.1 6.9.1.1
Register Description PWM Control Register (PWMCON) (Default Value: 0000_0000)
Bit 7: Reserved Bit 6~4: PWM 4 Frequency Select Input clock=24MHz : 111: Reserved, 110: 375 KHz, 101: 750 KHz, 100: 1.5 MHz. 011: 3 MHz, 010: 6 MHz, 001: 12 MHz, 000: 24 MHz. Input clock=12MHz : 111: Reserved, 110: Reserved, 101: 375 KHz, 100: 750KHz. 011: 1.5 MHz, 010: 3 MHz, 001: 6 MHz, 000: 12 MHz. Bit 3: Reserved Bit 2~0: PWM 3 Frequency Select Input clock=24MHz : 111: Reserved, 110: 375 KHz, 101: 750 KHz, 100: 1.5 MHz. 011: 3 MHz, 010: 6 MHz, 001: 12 MHz, 000: 24 MHz. Input clock=12MHz : 111: Reserved, 110: Reserved, 101: 375 KHz, 100: 750KHz. 011: 1.5 MHz, 010: 3 MHz, 001: 6 MHz, 000: 12 MHz.
6.9.1.2
PWM 1 Period Register (PWM1P) (Default Value: 0000_0000)
Use the 8-bit register to control width of a full period output.
- 70 -
W83L951DG/W83L951FG
6.9.1.3 PWM 2 Period Register (PWM2P) (Default Value: 0000_0000)
Use the 8-bit register to control width of a full period output.
6.9.1.4
PWM 3 Period Register (PWM3PH, PWM3PL) (Default Value: 0000h)
Use the 16-bit register to control width of a full period output.
6.9.1.5
PWM 4 Period Register (PWM4PH, PWM4PL) (Default Value: 0000h)
Use the 16-bit register to control width of a full period output.
6.9.1.6
PWM 1 High Level Register (PWM1H) (Default Value: 0000_0000)
PWM1H is defined as high signal width for PWM1 output. It is an 8-bit register.
6.9.1.7
PWM 2 High Level Register (PWM2H) (Default Value: 0000_0000)
PWM2H is defined as high signal width for PWM2 output. It is an 8-bit register.
6.9.1.8
PWM 3 High Level Register (PWM3HH, PWM3HL) (Default Value: 0000_0000)
(PWM3HH, PWM3HL) is defined as high signal width for PWM3 output. It is a 16-bit register.
6.9.1.9
PWM 4 High Level Register (PWM4HH, PWM4HL) (Default Value: 0000_0000)
(PWM4HH, PWM4HL) is defined as high signal width for PWM4 output. It is a 16-bit register.
- 71 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.10 UART Block
W83L951DG/FG supports one Universal asynchronous serial I/O mode (UART) .Eight serial data transfer formats can be selected, for vary selection of Stop bit, Parity, Parity check, Data length, and the transfer formats used by a transmitter and receiver must be identical. The transmitter and receiver shift registers each have a buffer, but the two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive buffer register can hold a byte while the next byte is being received. Table 6-18.UART Register Define UART Block(5) ExtAddr 30 31 32 33 34 Name UARTCON UARTSTS BRGH BRGL UARTBUF 7 TxEn 6 TS 5 RxEn OverErr 4 3 2 1 RxBFull 0 Reserved TxBFull PARE PARS STPS CHAS Reserved
ParErr FrameErr
Baud Rate Generator High Byte[7:0] Baud Rate Generator Low Byte[7:0] UART Transmit / Receive Buffer[7:0]
Gray: Only with System Reset to initial.
6.10.1 Register Description 6.10.1.1 UART Control Register (UARTCON) (Default Value: 0000_0000)
Bit 7: Transmit enable bit (TE) 0: Transmit disabled. 1: Transmit enable. Bit 6: Transmit Speed up bit (TS) (Reserved) 0: Disable. 1: Enable. Bit 5: Receive enable bit (RE) 0: Receive disable. 1: Receive enable. Bit 4: Parity enable bit (PARE). 0: Parity Bit disable. 1: Parity Bit enable. Bit 3: Parity selection bit (PARS). 0: Odd parity. 1: Even parity. Bit 2: Stop bit length selection bit (STPS) 0: 1 stop bit. 1: 2 stop bits.
- 72 -
W83L951DG/W83L951FG
Bit 1: Character length selection bit (CHAS) . 0: 8 bits 1: 7 bits. Bit 0: User Define Register
6.10.1.2
UART Status Register (UARTSTS) (Default Value: 0000_0000)
Bit 7: Parity Error Status for Packet at Receive Buffer (PE) Read: 0 - No error, 1 - Parity error Bit 6: Framing Error Status for Packet at Receive Buffer (FE) Read: 0 - No error, 1 - Framing error Bit 5: Overrun Error Interrupt (OE) For UART Rx Interrupt, users need to write this bit to clear. Read: 0 - No error 1 - Overrun error Write: 0 - No Chang 1 - Clear Bit 4~2: No use (return `L' when read) Bit 1: Receive Buffer Full Status Flag (RBF) Receive Buffer Full generates the interrupt. Read buffer can clear the flag. 0: Buffer empty 1: Buffer full Bit 0: Transmit Buffer Full Status Flag (TBF) Transmit Buffer Empty generates the interrupt. Write buffer can clear the flag. And next byte is allowed to write into the buffer. 0: Buffer empty 1: Buffer full
- 73 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.10.1.3 Baud Rate Generator High/Low Byte Register (BRGH/BRGL) (Default Value: 0000_0000_0000_0000)
Input clock=24MHz : Baud Rate Period Width = (N+1) / 3MHz. And N = {BRGH, BRGL} Input clock=12MHz : Baud Rate Period Width = 2(N+1) / 3MHz. And N = {BRGH, BRGL}
6.10.1.4
UART Transmit / Receive Buffer (UARTBUF) (Default Value: 0000_0000)
Read: Receive Buffer Write: Transmit Buffer
- 74 -
W83L951DG/W83L951FG
6.11 Consumer Infrared Communications Receiver Block
The CIrCC implements hardware-level decoding for the NEC Consumer IR Remote Control format. The hardware decoder may be used to generate a wake-up event or to send parts of the received message frame to the FIFO. The No Care Custom Code (NCCC), No Care Data Code (NCDC), PME Wake and Frame bits of the Consumer IR Control register configure the hardware decoder. About NEC Consumer IR Format, the NEC Consumer IR Remote Control format specifies a 38 kHz carrier, 13ms of sync framing, and 32 bits of pulse-position modulated (PPM) message data. The message data includes an 8 bit Custom Code field, an 8 bit Custom Code' field, an 8 bit Data Code field, and an 8 bit Data Code' field. A single frame of the NEC PPM Consumer Remote Control signal is shown in Figure 14-1. The Custom Code fields in this protocol uniquely address message frames for specific devices. The Custom Code fields can be used as a 16 bit address or as an 8 bit address followed by the bit-wise complement of the Custom Code field Custom Code. The Data Code field is an 8 bit command code, Data Code' is the bit-wise complement of Data Code. Note: The CIrCC hardware can decode NEC protocol framing (sync pulse, 32 bit PPM message data) at any data rate, depending on the programmed Bit Rate Divider (BRD). Table 6-19.Consumer Infrared Communications Receiver Register Define
CIR BLOCK(3) EXTADDR NAME 7 6 5 4 3 2 1 0
40 41 42 43 44 45
CIRCON CIRBRD CIRDATA1 CIRDATA2 CIRDATA3 CIRDATA4
DFE
SFE
REP
FINISH
DM
SM
RM
RXINV
Baud Rate Divider[7:0] CIR Receive Data 1[7:0] CIR Receive Data 2[7:0] CIR Receive Data 3[7:0] CIR Receive Data 4[7:0]
Gray: Only with System Reset to initial.
6.11.1 Register Description 6.11.1.1 CIR Configure Register (CIRCON) (Default Value: 0000_0000)
Bit 7: Data Frame Error Status Flag (Write `HIGH' to Clear) When Data Frame Error flag occurs, CIR Interrupt is generated. Write the bit can clear Data Frame Error Flag. Read: 0 - No error 1 - Data frame Error
- 75 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Write: 0 - No Change
1 - Clear
Bit 6: Start Frame Error Status Flag (Write `HIGH' to Clear) When Start Frame Error flag occurs, CIR Interrupt is generated. Write the bit can clear Start Frame Error Flag. Read: 0 - No error 1 - Start Frame Error Write: 0 - No Change 1 - Clear Bit 5: Repeat Status Flag (Write `HIGH' to Clear) When Repeat Flag occurs, CIR Interrupt is generated. Write the bit can clear Repeat Flag. Read: 0 - No happened 1 - Repeat Packet Received. Write: 0 - No Change 1 - Clear Bit 4: Finish Status Flag (Write `HIGH' to Clear) When Finish Flag occurs, CIR Interrupt is generated. Write the bit can clear Finish Flag. Read: 0 - No happened 1 - Packet Received is finish. Write: 0 - No Chang 1 - Clear Bit 3: Data Frame Error Interrupt Mask Enable 0 - Enable. 1 - Disable. Bit 2: Start Frame Error Interrupt Mask Enable 0 - Enable. 1 - Disable.
- 76 -
W83L951DG/W83L951FG
Bit 1: Repeat Interrupt Mask Enable 0 - Enable. 1 - Disable. Bit 0: Rx Signal Invert Enable Enable CIR Rx signal Convert Function 0 - Enable. 1 - Disable.
6.11.1.2
Baud Rate Divider (CIRBRD) (Default Value: 0101_0101)
Input clock=24MHz : The Transmit and Receive Bit Rate Divider register is used to extract a serial NRZ data stream for the CIrCC SCE. The divider is eight bits wide. The input clock to the Bit Rate Divider is 100 KHz (Carrier Frequency Divider input clock 16). The relationship between the Bit Rate Divider (BRD) and the Bit Rate (Fb) is as follows: BRD = (.1MHz/Fb) - 1 For example, program the Bit Rate Divider with 55 ('37'Hex) for a .562ms Remote Control bit cell like for the NEC remote control frame format: Fb = 1.786 KHz. This is ~.5% accuracy. Table 9 contains representative BRD vs. BitRate relationships. The Bit Rate range is 100 KHz to 390.625Hz. Input clock=12MHz : The Transmit and Receive Bit Rate Divider register is used to extract a serial NRZ data stream for the CIrCC SCE. The divider is eight bits wide. The input clock to the Bit Rate Divider is 50 KHz (Carrier Frequency Divider input clock 16). The relationship between the Bit Rate Divider (BRD) and the Bit Rate (Fb) is as follows: BRD = (.05MHz/Fb) - 1 For example, program the Bit Rate Divider with 55 ('37'Hex) for a .562ms Remote Control bit cell like for the NEC remote control frame format: Fb = 0.893 KHz. This is ~.5% accuracy. Table 9 contains representative BRD vs. BitRate relationships. The Bit Rate range is 50 KHz to 190Hz.
- 77 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Figure 6-2.NEC CIR Frame Format Table 6-20.Bit Rate Divider (BRD) V.S Bit Rate (Fb)
INPUT CLOCK=12MHZ BRD FB (KHZ) BRD FB (KHZ) BRD FB (KHZ) BRD FB (KHZ)
003 007 011 015 019 023 027 031 035 039 043 047 051 055 059 063
12.5 6.25 4.1665 3.125 2.5 2.0835 1.7855 1.5625 1.389 1.25 1.1365 1.0415 0.9615 0.893 0.8335 12.5
067 071 075 079 083 087 091 095 099 103 107 111 115 119 123 127
0.7355 0.6945 0.658 0.625 0.595 0.568 0.5435 0.521 0.5 0.481 0.463 0.4465 0.431 0.4165 0.403 0.781
131 135 139 143 147 151 155 159 163 167 171 175 179 183 187 191
0.379 0.3675 0.357 0.347 0.338 0.329 0.3205 0.3125 0.305 0.2975 0.2905 0.284 0.278 0.2715 0.266 0.521
195 199 203 207 211 215 219 223 227 231 235 239 243 247 251 255
0.255 0.25 0.245 0.2405 0.236 0.2315 0.2275 0.223 0.2195 0.2155 0.212 0.2085 0.205 0.2015 0.1985 0.19
- 78 -
W83L951DG/W83L951FG
Continued.
INPUT CLOCK=24MHZ BRD FB (KHZ) BRD FB (KHZ) BRD FB (KHZ) BRD FB (KHZ)
BRD 003 007 011 015 019 023 027 031 035 039 043 047 051 055 059 063
Fb (kHz) 25.000 12.500 8.333 6.250 5.000 4.167 3.571 3.125 2.778 2.500 2.273 2.083 1.923 1.786 1.667 1.563
BRD 067 071 075 079 083 087 091 095 099 103 107 111 115 119 123 127
Fb (kHz) 1.471 1.389 1.316 1.250 1.190 1.136 1.087 1.042 1.000 0.962 0.926 0.893 0.862 0.833 0.806 0.781
BRD 131 135 139 143 147 151 155 159 163 167 171 175 179 183 187 191
Fb (kHz) 0.758 0.735 0.714 0.694 0.676 0.658 0.641 0.625 0.610 0.595 0.581 0.568 0.556 0.543 0.532 0.521
BRD 195 199 203 207 211 215 219 223 227 231 235 239 243 247 251 255
Fb (kHz) 0.510 0.500 0.490 0.481 0.472 0.463 0.455 0.446 0.439 0.431 0.424 0.417 0.410 0.403 0.397 0.391
6.11.1.3 6.11.1.4 6.11.1.5 6.11.1.6
CIR Receive Data 1(CIRDATA1) (Default Value: 0000_0000) CIR Receive Data 1/2/3/4(CIRDATA1/2/3/4) (Default Value: 0000_0000) CIR Receive Data 1/2/3/4(CIRDATA1/2/3/4) (Default Value: 0000_0000) CIR Receive Data 1/2/3/4(CIRDATA1/2/3/4) (Default Value: 0000_0000)
Read: CIR 1st Received Data Buffer
Read: CIR 2nd Received Data Buffer
Read: CIR 3rd Received Data Buffer
Read: CIR 4th Received Data Buffer
- 79 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.12 A/D Converter Block
W83L951DG/FG provides 8 A/D inputs. Analog input pin is selected in A/D Converter Register 0. The A-D conversion register is a read-only register that stores the result of an A-D conversion. When reading this register during an A-D conversion, the previous conversion result is read. Table 6-21 A/D Convert Register Define
A/D CONVERT BLOCK(4) EXTADDR NAME 7 6 5 4 3 2 1 0
50 51 54
AD1 AD2 PADMODE
ADCST AD7
Analog Input Select AD6 AD5 AD4
ADCC AD3
Reserved AD2
Analog [1:0] AD1 AD0
Analog [9:2]
Gray: Only with System Reset to initial.
6.12.1 Register Description
A/D converter is 10-bit converter. The VREF is Input of VREF pin. The formula: A/D converter result= (Analog [9:0] / 1024) x VREF
6.12.1.1
A/D Converter Register 1 (AD1) (Default Value: 0000_00??)
Bit 7: ADC Start Bit 1: Start (Only one time) 0: No change. When A/D Conversion Complete Status Bit is high, write 1 to this bit to start A/D convert. And ADC Start Bit keeps low until hardware receives this request and can receive next request. And ADC Start Bit changes from low to high at the time. Bit 6~4: Analog Input Pin Select 000: GP60, 001: GP61, 010: GP62, 011: GP63, 100: GP64, 101: GP65, 110: GP66, 111: GP67. Bit 3: A/D Conversion Complete Status Bit (Read Only) 0: Conversion in progress. 1: Conversion completed. Bit 2: Reserved Bit 1~0: A/D Converter Result [1:0] A/D converter result bit1 is LSB. When A/D Conversion Complete Status Bit is high, A/D Converter Result is valid.
- 80 -
W83L951DG/W83L951FG
6.12.1.2 A/D Converter Register 2 (AD2) (Default Value: ????_????)
Bit 7~0: A/D Converter Result [9:2] A/D Converter Result bit 9 is MSB. When A/D Conversion Complete Status Bit is high, A/D Converter Result is valid.
6.12.1.3
Pad Mode Register (PADMODE) (Default Value: 0000_0000)
Bit 7~0: Pad mode select 0: Normal Mode 1: AD Mode
6.13 D/A Converter Block
The keyboard controller has two internal D-A converters (DA2 and DA1) with 8-bit resolution. The result of D-A conversion is output to the DA2 or DA1 pin. Table 6-22.D/A Converter Register Define
A/D CONVERT BLOCK(4) EXTADDR NAME 7 6 5 4 3 2 1 0
52 53 Note:
DA1 DA2
D/A 1 Convert Register [7:0] D/A 2 Convert Register [7:0]
Gray: Only with System Reset to initial.
6.13.1 Register Description 6.13.1.1 D-A conversion register 1(DA1) (Default Value: 0000_0000)
VGP 57 = VREF x (N 256)
VREF is the reference voltage. 6.13.1.2 D-A conversion register 2(DA2) (Default Value: 0000_0000)
VGP 56 = VREF x ( N 256)
VREF is the reference voltage.
- 81 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.14 Fan Tachometer Block
Fan Tachometer Block provides two groups of Fan Tachometer, can be by GP40, GP41 inputs the wave form and calculates automatically that corresponding Count of cycle of rotational speed is counted. When real RPM is lower than setting value, interrupt request will occur. Table 6-23.Fan Tachometer Register Define
FAN BLOCK(2) EXTADDR NAME 7 6 5 4 3 2 1 0
00 01 Note:
FAN1 FAN2
Fan 1 Count[7:0] Fan 2 Count[7:0]
Gray: Only with System Reset to initial.
6.14.1 Register Description 6.14.1.1
Read: Input clock=24MHz : Current Count. RPM = (60 x 1 x 10e6) / (2 x Count x 256) = 117187.5/Count Input clock=12MHz : Current Count. RPM = (60 x 1 x 10e6) / (4 x Count x 256) = 58593/Count. Write: Set Count of tolerance of minimum RPM. When real RPM is lower than setting value, interrupt request will occur. The relation between RPM and Count is as follows: Input clock=24MHz : RPM = (60 x 1 x 10e6) / (2 x Count x 256) = 117187.5/Count. Count = 117187.5/RPM. Input clock=12MHz : RPM = (60 x 1 x 10e6) / (4 x Count x 256) = 58593/Count. Count= 58593/RPM.
FAN 1/2 Count/Limit Register (FAN1/2) (Default Value: ????_????)
- 82 -
W83L951DG/W83L951FG
6.15 Real Time Clock Generator Block
Base on 32.768KHz, Real Time Clock Generator Block finishes counts which include seconds, minutes, and hours automatically. It also provides alarm function. When {RTCHR, RTCMIN, RTCSEC} and {RTCHRAL, RTCMINAL, RTCSECAL} are equal, interrupt will occur to Microprocessor automatically. Table 6-24.Real Time Clock Generator Register Define
REAL TIME CLOCK BLOCK(6) EXTADDR NAME 7 6 5 4 3 2 1 0
70 71 72 73 74 75 Note:
RTCSEC RTCSECAL RTCMIN RTCMINAL RTCHR RTCHRAL
RTC Seconds Register[7:0] RTC Seconds Alarm Register[7:0] RTC Minutes Register[7:0] RTC Minutes Alarm Register[7:0] RTC Hours Register[7:0] RTC Hours Alarm Register[7:0]
Gray: Only with System Reset to initial. RTCSEC, RTCMIN, RTCHR should initial after local reset.
6.15.1 Register Description 6.15.1.1 RTC Second Register (RTCSEC) (Default Value: 0000_0000)
Read: Indicate RTC second value at present. Write: Set RTC second value at present.
6.15.1.2
RTC Second Alarm Register (RTCSECAL) (Default Value: 0000_0000)
Read: Indicate RTC second alarm at present. Write: Set RTC second alarm value at present.
6.15.1.3
RTC Minute Register (RTCMIN) (Default Value: 0000_0000)
Read: Indicate RTC minute value at present. Write: Set RTC minute value at present.
- 83 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.15.1.4 RTC Minute Alarm Register (RTCMINAL) (Default Value: 0000_0000)
Read: Indicate RTC minute alarm value at present. Write: Set RTC minute alarm value at present.
6.15.1.5
RTC Hour Register (RTCHR) (Default Value: 0000_0000)
Read: Indicate RTC hour value at present. Write: Set RTC hour value at present.
6.15.1.6
RTC Hour Alarm Register (RTCHRAL) (Default Value: 0000_0000)
Read: Indicate RTC hour alarm minute value at present. Write: Set RTC hour alarm value at present.
- 84 -
W83L951DG/W83L951FG
6.16 External Interrupt Control Block
About External Interrupt, in W83L951DG/FG, External Interrupt Group1 (EXTINT1[7:0]), External Interrupt Group2 (EXTINT2[7:0]) and External Interrupt Group3 (EXTINT3[7:0]) interrupt source pins are same as GPA[7:0], GPB[7:0] and GPC[7:0]. Table 6-25.External Interrupt Control Register Define
INTERRUPT BLOCK(17) EXTADDR NAME 7 6 5 4 3 2 1 0
80 81 82 83 84 85 88 89 8A 8B
EXTINTE1 EXTINTE2 EXTINTE3 EXTINTREQ1 EXTINTREQ2 EXTINTREQ3 EXTINTT1 EXTINTT2 EXTINTT3 EXTINTT4
INT17 INT27 INT37 INT17 INT27 INT37 INT17 INT27 INT33 INT37
INT16 INT26 INT36 INT16 INT26 INT36 INT16 INT26
INT15 INT25 INT35 INT15 INT25 INT35 INT15 INT25 INT32 INT36
INT14 INT24 INT34 INT14 INT24 INT34 INT14 INT24
INT13 INT23 INT33 INT13 INT23 INT33 INT13 INT23 INT31 INT35
INT12 INT22 INT32 INT12 INT22 INT32 INT12 INT22
INT11 INT21 INT31 INT11 INT21 INT31 INT11 INT21 INT30 INT34
INT10 INT20 INT30 INT10 INT20 INT30 INT10 INT20
Note: All register initial after system reset.
6.16.1 Register Description 6.16.1.1 External Interrupt Enable 1/2/3 Register (EXTINTE1/2/3) (Default Value: 0000_0000)
1: Enable. In enable state, external interrupt source will cause external interrupt request to generate the interrupt to Microprocessor. 0: Disable.
6.16.1.2 External Interrupt Request 1/2/3 Register (EXTINTREQ1/2/3) (Default Value: 0000_0000)
Bit7~0: External Interrupt Request Read: 1: Requested, 0: No Requested. Write: 1: Clear Request, 0: No Change
- 85 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.16.1.3 External Interrupt Trigger Select 1 Register (EXTINTT1) (Default Value: 0000_0000)
Bit 7~0:INT17~10 Trigger Type Indicate the trigger type of External Interrupt 17~10. 1: Rising Edge 0: Falling Edge.
6.16.1.4 External Interrupt Trigger Select 2 Register (EXTINTT2) (Default Value: 0000_0000)
Bit 7~0:INT27~20 Trigger Type Indicate the trigger type of External Interrupt 27~20. 1: Rising Edge 0: Falling Edge.
6.16.1.5 External Interrupt Trigger Select 3 Register (EXTINTT3) (Default Value: 0000_0000)
Bit 7~6:INT33 Trigger Type Indicate the trigger type of External Interrupt 33. 1x: Rising Edge& Falling Edge, 01: Rising Edge, 00: Falling Edge Bit 5~4:INT32 Trigger Type Indicate the trigger type of External Interrupt 32. 1x: Rising Edge& Falling Edge, 01: Rising Edge, 00: Falling Edge Bit 3~2:INT31 Trigger Type Indicate the trigger type of External Interrupt 31. 1x: Rising Edge& Falling Edge, 01: Rising Edge, 00: Falling Edge Bit 1~0:INT30 Trigger Type Indicate the trigger type of External Interrupt 30. 1x: Rising Edge& Falling Edge, 01: Rising Edge 00: Falling Edge
- 86 -
W83L951DG/W83L951FG
6.16.1.6 External Interrupt Trigger Select 4 Register (EXTINTT4) (Default Value: 0000_0000)
Bit 7~6:INT37 Trigger Type Indicate the trigger type of External Interrupt 37. 1x: Rising Edge& Falling Edge, 01: Rising Edge 00: Falling Edge Bit 5~4:INT36 Trigger Type Indicate the trigger type of External Interrupt 36. 1x: Rising Edge& Falling Edge, 01: Rising Edge 00: Falling Edge Bit 3~2:INT35 Trigger Type Indicate the trigger type of External Interrupt 35. 1x: Rising Edge& Falling Edge, 01: Rising Edge 00: Falling Edge Bit 1~0:INT34 Trigger Type Indicate the trigger type of External Interrupt 34. 1x: Rising Edge& Falling Edge, 01: Rising Edge 00: Falling Edge
- 87 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.17 Flash Memory
The W83L951DG/FG has a 64KByte, 3.3-volt only CMOS flash memory. The byte-wide (x 8) data appears on DQ7-DQ0. The device can be programmed and erased in-system with a standard 3.3V power supply. A 12-volt VPP is not required. The unique cell architecture of the Flash results in fast program/erase operations with extremely low current consumption (compared to other comparable 3.3-volt flash memory products). The device can also be programmed and erased by using standard EPROM programmers.
6.17.1 External Programming Mode
The context of flash in Winbond Keyboard controller is empty by default. At the first use, you must program the flash by external writer device. For programming the flash by external device, the Winbond Keyboard controller must enter the flash-programming mode by TEST# Pin is connected to GND. RESET# Pin is connected to GND. FA [7:0] and FD [7:0] port is combined to GP07 to GP00. FA [7:0] is latched by the ALE (GP34). In External Programming Mode, W83L951DG/FG protects Internal Flash data, so W83L951DG/FG will close "Read Command". Under this condition, users must run "Erase Command" to use "Read Command".
6.17.2 Internal Programming Mode
In W83L951DG/FG, in addition to access internal flash by outside, it provides to access SFR by Microprocessor. When Enable Memory Bit of Memory Mapping Control Register is high, and PC is F800~FFFFh, Microprocessor can access Internal Flash by SFR. Table 6-26.Internal Programming Flash Register Define
INTERNAL PROGRAMMING FLASH INTADDR NAME 7 6 5 4 3 2 1 0
F9 FA FB FC
FCON FADDH FADDL FDATA
CEB A[15:8] A[7:0] DQ[7:0]
OEB
WEB
Reserved
EXCHANG_GP
6.17.2.1 6.17.2.2
Flash Control Register (FCON) (Default Value: 0000_0000) Bit7: Flash Chip Select Enable (CEB)
Like CE# Pin. Refer to next section for further details. Bit6: Flash Output Enable (OEB) Like OE# Pin. Refer to next section for further details. Bit5: Flash Write Enable (WEB) Like WE# Pin. Refer to next section for further details. Bit4~Bit1: Reserved Bit0: Exchange GPIOA/B/C to GPIO1/0/3 Function (Reserved)
- 88 -
W83L951DG/W83L951FG
6.17.2.3 6.17.2.4 6.17.2.5 Flash Address High Byte Register (FADDH) (Default Value: 0000_0000) Flash Address Low Byte Register (FADDL) (Default Value: 0000_0000) Flash Data Register (FDATA) (Default Value: 0000_0000)
Address [15:8] Input, Like A [15:8] Pin. Refer to next section for further details.
Address [7:0] Input, Like A [7:0] Pin. Refer to next section for further details.
Write: Data Input Read: Data Output Like DQ [7:0] Pin. Refer to next section for further details.
6.17.3 Device Bus Operation 6.17.3.1 Read Mode
The read operation of the Internal Flash is controlled by #CE and #OE, both of which have to be low for the host to obtain data from the outputs. #CE is used for device selection. When #CE is high, the chip is de-selected and only standby power will be consumed. #OE is the output control and is used to gate data from the output pins. The data bus is in high impedance state when either #CE or #OE is high. Refer to the timing waveforms for further details.
6.17.3.2
Write Mode
Device erasure and programming are accomplished via the command register. The contents of the register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The command register is written by bringing #WE to logic low state, while #CE is at logic low state and #OE is at logic high state. Addresses are latched on the falling edge of #WE or #CE, whichever happens later; while data is latched on the rising edge of #WE or #CE, whichever happens first. Standard microprocessor write timings are used. Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
6.17.3.3
Output Disable Mode
With the #OE input at a logic high level (VIH), output from the device is disabled. This will cause the output pins to be in a high impedance state.
6.17.3.4
Write Pulse "Glitch" Protection
Noise pulses of less than 10 ns (typical) on #OE, #CE, or #WE will not initiate a write cycle.
6.17.4 Command Definitions
Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in the improper sequence will reset the device to the read mode. "Command Definitions" defines the valid register command sequences.
- 89 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.17.4.1 Read Command
The device will automatically power-up in the read state. In this case, a command sequence is not required to read data. Standard microprocessor read cycles will retrieve array data. This default value ensures that no spurious alteration of the memory content occurs during the power transition. The device will automatically returns to read state after completing an Embedded Program or Embedded Erase algorithm. Refer to the AC Read Characteristics and Waveforms for the specific timing parameters.
6.17.4.2
Byte Program Command
The device is programmed on a byte-by-byte basis. Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two "unlock" write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the embedded program algorithm. Addresses are latched on the falling edge of #CE or #WE, whichever happens later and the data is latched on the rising edge of #CE or #WE, whichever happens first. The rising edge of #CE or #WE (whichever happens first) begins programming using the Embedded Program Algorithm. Upon executing the algorithm, the system is not required to provide further controls or timings. The device will automatically provide adequate internally generated program pulses and verify the programmed cell margin. The automatic programming operation is completed when the data on DQ7 (also used as Data Polling) is equivalent to the data written to this bit at which time the device returns to the read mode and addresses are no longer latched (see "Hardware Sequence Flags"). Therefore, the device requires that a valid address to the device be supplied by the system at this particular instance of time for Data Polling operations. Data Polling must be performed at the memory location which is being programmed. Any commands written to the chip during the Embedded Program Algorithm will be ignored. If a hardware reset occurs during the programming operation, the data at that particular location will be corrupted. Programming is allowed in any sequence and across sector boundaries. Beware that a data "0" cannot be programmed back to a "1". Attempting to program 0 back to 1, the toggle bit will stop toggling. Only erase operations can convert "0"s to "1"s. Refer to the Programming Command Flow Chart using typical command strings and bus operations.
6.17.4.3
Chip Erase Command
Chip erase is a six-bus-cycle operation. There are two "unlock" write cycles, followed by writing the "set-up" command. Two more "unlock" write cycles are asserted, followed by the chip erase command. Chip erase does not require the user to program the device prior to erase. Upon executing the Embedded Erase Algorithm command sequence the device will automatically erase and verify the entire memory for an all one data pattern. The erase is performed sequentially on each sectors at the same time (see "Feature"). The system is not required to provide any controls or timings during these operations. The automatic erase begins on the rising edge of the last #WE pulse in the command sequence and terminates when the data on DQ7 is "1" at which time the device returns to read the mode. Refer to the Erase Command Flow Chart using typical command strings and bus operations.
- 90 -
W83L951DG/W83L951FG
6.17.5 Write Operation Status 6.17.5.1 DQ7: Data Polling
The W39L040 device features Data Polling as a method to indicate to the host that the embedded algorithms are in progress or completed. During the Embedded Program Algorithm, an attempt to read the device will produce the complement of the data last written to DQ7. Upon completion of the Embedded Program Algorithm, an attempt to read the device will produce the true data last written to DQ7. During the Embedded Erase Algorithm, an attempt to read the device will produce a "0" at the DQ7 output. Upon completion of the Embedded Erase Algorithm, an attempt to read the device will produce a "1" at the DQ7 output. For chip erase, the Data Polling is valid after the rising edge of the sixth pulse in the six #WE write pulse sequences. For sector erase, the Data Polling is valid after the last rising edge of the sector erase #WE pulse. Data Polling must be performed at sector addresses within any of the sectors being erased. Otherwise, the status may not be valid. Just prior to the completion of Embedded Algorithm operations DQ7 may change asynchronously while the output enable (#OE) is asserted low. This means that the device is driving status information on DQ7 at one instant of time and then that bytes valid data at the next instant of time. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the Embedded Algorithm operations and DQ7 has a valid data, the data outputs on DQ0- DQ6 may be still invalid. The valid data on DQ0-DQ7 will be read on the successive read attempts. The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase Algorithm, or sector erase time-out (see "Command Definitions").
6.17.5.2
DQ6: Toggle Bit
The Flash also features the "Toggle Bit" as a method to indicate to the host system that the embedded algorithms are in progress or completed. During an Embedded Program or Erase Algorithm cycle, successive attempts to read (#OE toggling) data from the device at any address will result in DQ6 toggling between one and zero. Once the Embedded Program or Erase Algorithm cycle is completed, DQ6 will stop toggling and valid data will be read on the next successive attempt. During programming, the Toggle Bit is valid after the rising edge of the fourth #WE pulse in the four write pulse sequence. For chip erase, the Toggle Bit is valid after the rising edge of the sixth #WE pulse in the six write pulse sequence. For sector/page erase, the Toggle Bit is valid after the last rising edge of the sector/page erase #WE pulse. The Toggle Bit is active during the sector/page erase time-out. Either #CE or #OE toggling will cause DQ6 to toggle.
- 91 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.17.6 Table of Operating Modes
Table 6-27.Device Bus Operations MODE Read Write Standby Output Disable Table 6-28.Command Define
COMMAND DESCRIPTION NO. OF CYCLE 1ST 2ND 3RD 4TH 5TH 6TH ADDR,DATA
#CE VIL VIL VIH VIL
#OE VIL VIH X VIH
#WE VIH VIL X VIH
A0 A0 A0 X X
A1 A1 A1 X X
DQ0~DQ7 Dout Din High Z High Z
Read Byte Program Chip Erase Page Erase Product ID Entry Product ID Exit 1 Product ID Exit 2
Notes:
1 4 6 6 3 3 1
Ain, Dout 5555,AA 5555,AA 5555 AA 5555 AA 5555 AA XXXX F0
.
2AAA,55 2AAA,55 2AAA 55 2AAA 55 2AAA 55
5555,A0 5555,80 5555 80 5555 90 5555 F0
Ain, Din 5555,AA 5555 AA 2AAA,55 2AAA 55 5555,10 PA 50
1. Address Format: A14 ~ A0(Hex); Data Format: DQ7 ~ DQ0(Hex) 2. Either one the two Product ID Exit commands can be used. 3. PA: Page Address = FXXXh to 0XXXh for page 15 to page 0.
- 92 -
W83L951DG/W83L951FG
6.17.7 Embedded Algorithm 6.17.7.1 Embedded Programming Algorithm
Figure 6-3.Embedded Programming Algorithm State Diagram
- 93 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.17.7.2 Embedded Erase Algorithm
Figure 6-4.Embedded Erase Algorithm State Diagram
- 94 -
W83L951DG/W83L951FG
6.17.7.3 Embedded #Data Polling Algorithm
Figure 6-5.Embedded #Data Polling Algorithm State Diagram Note: VA = Byte Address for programming = Any Group Address during chip erase
6.17.7.4
Embedded Toggle Bit Algorithm
Figure 6-6.Embedded Toggle Bit Algorithm State Diagram
- 95 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
6.17.8 Timing Parameters
Table 6-29.Read Cycle Timing Parameters Table
PARAMETER SYMBOL MIN. MAX. UNIT
Read Cycle Time Chip Enable Access Time Address Access Time Output Enable Access Time #CE Low to Active Output #OE Low to Active Output #CE High to High-Z Output #OE High to High-Z Output Output Hold from Address Change
TRC TCE TAA TOE TCLZ TOLZ TCHZ TOHZ TOH
90 0 0 0
90 90 45 25 25 -
ns ns ns ns ns ns ns ns ns
Note: (VDD = 3.3V 0.3V, VSS = 0V, TA = 0 to 70 C or -40 to 85 C)
Table 6-30.Write Cycle Timing Parameters Table
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
Address Setup Time Address Hold Time #WE and #CE Setup Time #WE and #CE Hold Time #OE High Setup Time #OE High Hold Time #CE Pulse Width #WE Pulse Width #WE High Width Data Setup Time Data Hold Time Byte Programming Time Chip Erase Cycle Time Sector/Page Erase Cycle Time
TAS TAH TCS TCH TOES TOEH TCP TWP TWPH TDS TDH TBP TEC TEP
0 40 0 0 0 0 100 100 100 40 10 -
35 50 12.5
50 100 25
nS nS nS nS nS nS nS nS nS nS nS S mS mS
- 96 -
W83L951DG/W83L951FG
Table 6-31.Power-up Timing Parameters Table
PARAMETER SYMBOL TYPICAL UNIT
Power-up to Read Operation Power-up to Write Operation
TPU. READ TPU. WRITE
100 5
S mS
6.17.9 Timing Waveforms
The Timing Waveforms don't contain ALE(GP34 and TS(GP33). If using External Mode to access, TS pin must keep low. And use ALE(GP34) to do Low Address Byte(GP0) latch. ALE is high active and pulse width is at least 50ns. Low Address Byte(GP0) must be stable before ALE changes state from high to low.
Figure 6-7.Read Cycle Timing Diagram
- 97 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Figure 6-8.#WE Controlled Command Write Cycle Timing Diagram
Figure 6-9.#CE Controlled Command Write Cycle Timing Diagram
- 98 -
W83L951DG/W83L951FG
Figure 6-10.Chip Erase Timing Diagram
Figure 6-11.Data Polling Timing Diagram
- 99 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Figure 6-12.Toggle Bit Timing Diagram
- 100 -
W83L951DG/W83L951FG
7. SPECIFICATIONS
7.1 Absolute Maximum Ratings
PARAMETER RATING UNIT
Table 7-1 Absolute Maximum Rating Table Power Supply Voltage Input Voltage Operating Temperature Storage Temperature -0.5 to +4.6 3.3 10% 0 to +70 -55 to +125 V V C C
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device.
7.2
7.2.1
Analog Characteristics
ADC Characteristics
PARAMETER MIN TYP MAX UNIT
Resolution Input Accuracy Input Voltage Range Voltage Conversion Duration
10 3 AVcc 1
Bit LSB V ms
7.2.2
DAC Characteristics
PARAMETER MIN TYP MAX UNIT
Resolution Offset Error Output Voltage Range DAC Enable Delay
8 2 AVcc 10
Bit LSB V s
7.3
Power Supply Current Consumption
PARAMETER TYPICAL UNIT PIN CONDITIONS
Table 7-2 Power Supply Current Consumption Table Normal Mode Power Down Mode 30 10 mA uA
Output , No Load
- 101 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
7.4 DC Characteristics
(Ta = 0 C to 70 C, VDD = 3.3V 10%, VSS = 0V) I/O12tsm--Bi-directional pin, TTL level, Schmitt-trigger input, selectable 250uA/12mA sink capability, 12mA source capability
PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage Output Low Voltage Output High Voltage
VIL VIH ILIH ILIL VOL VOH 2.4 2.0
0.8 +1 -1 0.4
V V A A V V VIN = VDD VIN = 0 V IOL = 12 mA IOH = -12 mA / -250uA
(Ta = 0 C to 70 C, VDD = 3.3V 10%, VSS = 0V) I/O12tsai -- Bi-directional pin, TTL level, Schmitt-trigger input, Analog Input, 12mA source-sink capability
PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage Output Low Voltage Output High Voltage
VIL VIH ILIH ILIL VOL VOH 2.4 2.0
0.8 +1 -1 0.4
V V A A V V VIN = VDD VIN = 0 V IOL = 12 mA IOH = -12 mA
(Ta = 0 C to 70 C, VDD = 3.3V 10%, VSS = 0V) I/O12tsao -- Bi-directional pin, TTL level, Schmitt-trigger input, Analog Output, 12mA source-sink capability
PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage Output Low Voltage Output High Voltage
VIL VIH ILIH ILIL VOL VOH 2.4 2.0
0.8 +1 -1 0.4
V V A A V V VIN = VDD VIN = 0 V IOL = 12 mA IOH = -12 mA
- 102 -
W83L951DG/W83L951FG
(Ta = 0 C to 70 C, VDD = 3.3V 10%, VSS = 0V) I/O16tsh -- Bi-directional pin, TTL level, Schmitt-trigger input, 5V Tolerant, 16mA source-sink capability
PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage Output Low Voltage Output High Voltage
VIL VIH ILIH ILIL VOL VOH 2.4 2.0
0.8 +1 -1 0.4
V V A A V V VIN = VDD VIN = 0 V IOL = 16 mA IOH = -16 mA
(Ta = 0 C to 70 C, VDD = 3.3V 10%, VSS = 0V) I/O24ts -- Bi-directional pin, TTL level, Schmitt-trigger input, 16mA source-sink capability
PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage Output Low Voltage Output High Voltage
VIL VIH ILIH ILIL VOL VOH 2.4 2.0
0.8 +1 -1 0.4
V V A A V V VIN = VDD VIN = 0 V IOL = 24 mA IOH = -24 mA
(Ta = 0 C to 70 C, VDD = 3.3V 10%, VSS = 0V) Its -- Input pin, TTL level, Schmitt-trigger input
PARAMETER SYM. MIN. TYP. MAX. UNIT CONDITIONS
Input Low Voltage Input High Voltage Input High Leakage Input Low Leakage
VIL VIH ILIH ILIL 2.0
0.8 +1 -1
V V A A VIN = VDD VIN = 0 V
- 103 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
8. ORDERING INSTRUCTION
PART NUMBER PACKAGE TYPE PRODUCTION FLOW
W83L951DG W83L951FG
128PIN LQFP (LEADFREE) 128PIN QFP (LEADFREE)
Commercial, 0C to +70C Commercial, 0C to +70C
- 104 -
W83L951DG/W83L951FG
9. HOW TO READ THE TOP MARKING
inbond
W83L951DG 22299460-N1 504AAAB
1st line: Winbond logo 2nd line: W83L951DG, chip part number for Leadfree product 3rd line: Manufacture tracking code 22299460-N1 4th line: Tracking code 504 A A AB 504: Packages made in '03, week 04 A: Assembly house ID; A means ASE, O means OSE, G means GR... A: IC revision AB: Internal version
inbond
W83L951FG 22299460-N1 504AAAB
1st line: Winbond logo 2nd line: W83L951FG, chip part number for Leadfree product 3rd line: Manufacture tracking code 22299460-N1 4th line: Tracking code 504 A A AB 504: Packages made in '03, week 04 A: Assembly house ID; A means ASE, O means OSE, G means GR... A: IC revision AB: Internal version
- 105 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
10. PACKAGE DIMENSIONS
Winbond provides two packages for customers that contain 128- pin LQFP and 128-pin QFP.
128-pin LQFP
128pin- QFP
Dimension in mm Dimension in inch
HE E
102 65
Symbol
Min
0.25 2.57 0.10 0.10 13.90 19.90
Nom
0.35 2.72 0.20 0.15 14.00 20.00 0.50
Max
0.45 2.87 0.30 0.20 14.10 20.10
Min
0.010 0.101 0.004 0.004 0.547 0.783
Nom
0.014 0.107 0.008 0.006 0.551 0.787 0.020
Max
0.018 0.113 0.012 0.008 0.555 0.791
103
64
D
HD
128
39
1
e
b
38
A1 A2 b c D E e HD HE L L1 y 0
c
17.00 23.00 0.65
17.20 23.20 0.80 1.60
17.40 23.40 0.95
0.669 0.905 0.025
0.677 0.913 0.031 0.063
0.685 0.921 0.037
0.08 0 7 0
0.003 7
Note:
1.Dimension D & E do not include interlead flash. 2.Dimension b does not include dambar protrusion/intrusion . 3.Controlling dimension : Millimeter 4.General appearance spec. should be based on final visual inspection spec.
A A2 See Detail F Seating Plane A1 L L1 Detail F
y
5. PCB layout please use the "mm".
- 106 -
W83L951DG/W83L951FG
11. DEMO CIRCUITS
Matrix_Column[19..0] KC19 KC18 KC17 KC16 KC15 KC14 KC13 KC12 KC11 KC10 KC9 KC8 KC7 KC6 KC5 KC4 KC3 KC2 KC1 KC0 KR7 KR6 VCC1 C1 0.1U C2 10U
Matrix Keyboard Row Input Pull-High
RP1 KR7 KR6 KR5 KR4 1 2 3 4 4.7K RP2 KR3 KR2 KR1 KR0 1 2 3 4 4.7K 8 7 6 5 8 7 6 5
UART for Debug
For Firmware debug , suggest to keep the Pin65,Pin66 to UART function , and add test point for using. JP1 1 2 HEADER 2
VCC1
Matrix Keyboard
You can select 8x16 or 8x20 matrix keyboard. Pin73~77 can be KC16~19 of 8x20 matrix keyboard or GPIO20~23.
PWM0 PWM1 PWM2 PWM3 FAN0 FAN1 RXD TXD 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
PWM Fan Tachometer UART
RXD TXD
Matrix_Row[7..0]
951_Flash Switch
U1 VCC2 VCC1 R1 10K R17 4.7K 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 KBRST# GATE_A20 CLKRUN# LPCPD# LAD3 LAD2 LAD1 LAD0 SERIRQ LRESET# LFRAME# R4 R5 PS2_1CLK PS2_1DAT PS2_2CLK PS2_2DAT PS2_3CLK PS2_3DAT SDA0 SCL0 SDA1 SCL1 CNTR0 CNTR1 CIR_RX GP85 GP86 GP87 RESET# C11 1U VCC1 JP2 1 2 HEADER 2
VREF
KR5 KR4 KR3 KR2 KR1 KR0
System Clock
XOUT Q1 24MHZ 1M R16 C3 22P C4 22P XIN AVCC
AD
AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 DA2 DA1
DA
RTC Clock
XCOUT Q2 32.768KHZ C7 22P R2 10M~20M C8 22P XCIN
EXTINT35/GPC5 EXTINT34/GPC4 EXTINT33/GPC3 EXTINT32/GPC2 EXTINT31/GPC1 EXTINT30/GPC0 EXTINT27/GPB7 EXTINT26/GPB6 EXTINT25/GPB5 EXTINT24/GPB4 EXTINT23/GPB3 EXTINT22/GPB2 EXTINT21/GPB1 EXTINT20/GPB0 EXTINT17/GPA7 EXTINT16/GPA6 EXTINT15/GPA5 EXTINT14/GPA4 EXTINT13/GPA3 EXTINT12/GPA2 EXTINT11/GPA1 EXTINT10/GPA0 VCC1 GP97 GP96 GP95 GP94 GP93 GP92 GP91 GP90 GND
GP55 GP54 GP53 GP52 GP51 GP50 XOUT XIN TEST# XCOUT XCIN GPC7 GPC6
97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
GP35/M_KR5/FPEN# GP34/M_KR4/FLATCH GP33/M_KR3/FCTRL3 GP32/M_KR2/FCTRL2 GP31/M_KR1/FCTRL1 GP30/M_KR0/FCTRL0 VREF AD7/GP67 AD6/GP66 AD5/GP65 AD4/GP64 AD3/GP63 AD2/GP62 AD1/GP61 AD0/GP60 AVCC DA2/GP57 DA1/GP56 AGND GP55 GP54 GP53 GP52 GP51 GP50 XOUT XIN TEST# XCOUT XCIN EXTINT37/GPC7 EXTINT36/GPC6
GP36/M_KR6/FOEN# GP37/M_KR7/FCEN# GP00/M_KC0/FA0/FD0 GP01/M_KC1/FA1/FD1 GP02/M_KC2/FA2/FD2 GP03/M_KC3/FA3/FD3 GP04/M_KC4/FA4/FD4 GP05/M_KC5/FA5/FD5 GP06/M_KC6/FA6/FD6 GP07/M_KC7/FA7/FD7 GP10/M_KC8/FA8 GP11/M_KC9/FA9 GP12/M_KC10/FA10 GP13/M_KC11/FA11 GP14/M_KC12/FA12 GP15/M_KC13/FA13 GP16/M_KC14/FA14 GP17/M_KC15/FA15 VCC1 GP20/nM_KC16 GP21/nM_KC17 GP22/nM_KC18 GP23/nM_KC19 GP24/PWM0 GP25/PWM1 GP26/PWM2 GP27/PWM3 GND GP40/FAN_TACH0 GP41/FAN_TACH1 GP42/RXD GP43/TXD
Remark: GP30~GP37(pin95~pin102) should to pull up VCC . If design for S3,S5 wake up by matrix keyboard, please pull up to standby VCC.
W83L951D
GP44/KBRST# GP45/GATE_A20 GP46/CLKRUN# GP47 VCC2 LAD3 LAD2 LAD1 LAD0 GND SERIRQ LRESET# LFRAME# LCLK RESET# VCC1 GP70/PS2_1CLK GP71/PS2_1DAT GP72/PS2_2CLK GP73/PS2_2DAT GP74/PS2_3CLK GP75/PS2_3DAT GP76/SDA0 GP77/SCL0 GP80/SDA1 GP81/SCL1 CNTR0/GP82 CNTR1/GP83 CIR_RX/GP84 GP85 GP86 GP87
LPC Interface
TEST# 33 0 VCC1
R3 4.7K JP3 1 2 HEADER 2
PCICLK RESET# C5 10U
C6 0.1U
TEST# RESET# 0 0 0 1 0 1
Chip Status
PS2 Interface SMBUS CIR Receiver
Internal flash access enable Normal operation by direct external rom Normal reset Normal operation
1 1
PS2 Interface and SMBUS Pull-high
Please select 3.3V or 5V pull-high based on your request in PS2 device. VCC1 VCC1
R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K W83L951D PS2_1CLK PS2_1DAT PS2_2CLK PS2_2DAT PS2_3CLK PS2_3DAT SDA0 SCL0 SDA1 SCL1 VCC1 Winbond Electronic Corp. Title C9 10U C10 0.1U W83L951D SCHEMATIC Size B Date: Document Number Wednesday , June 15, 2005 Sheet 1 of 1 Rev 0.52
VCC1 and VCC2:
VCC1 is W83L951D normal power input, it can be 3.3VCC or 3.3VSB or 3.3Vbat based on customer's design. VCC2 is power status that indicates power status of LPC interface. Please connect it to 3.3VCC from LPC interface.
GPC5 GPC4 GPC3 GPC2 GPC1 GPC0 GPB7 GPB6 GPB5 GPB4 GPB3 GPB2 GPB1 GPB0 GPA7 GPA6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
GP90 GP91 GP92 GP93 GP94 GP95 GP96 GP97 GPA0 GPA1 GPA2 GPA3 GPA4 GPA5
- 107 -
Publication Release Date: August 2006 Revision 1.0
W83L951DG/W83L951FG
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales.
Headquarters
No. 4, Creation Rd. III, Science-Based Industrial Park, Hsinchu, Taiwan TEL: 886-3-5770066 FAX: 886-3-5665577 http://www.winbond.com.tw/
Winbond Electronics Corporation America
2727 North First Street, San Jose, CA 95134, U.S.A. TEL: 1-408-9436666 FAX: 1-408-5441798
Winbond Electronics (Shanghai) Ltd.
27F, 2299 Yan An W. Rd. Shanghai, 200336 China TEL: 86-21-62365999 FAX: 86-21-62365998
Taipei Office
9F, No.480, Rueiguang Rd., Neihu District, Taipei, 114, Taiwan, R.O.C. TEL: 886-2-8177-7168 FAX: 886-2-8751-3579
Winbond Electronics Corporation Japan
7F Daini-ueno BLDG, 3-7-18 Shinyokohama Kohoku-ku, Yokohama, 222-0033 TEL: 81-45-4781881 FAX: 81-45-4781800
Winbond Electronics (H.K.) Ltd.
Unit 9-15, 22F, Millennium City, No. 378 Kwun Tong Rd., Kowloon, Hong Kong TEL: 852-27513100 FAX: 852-27552064
Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners.
- 108 -

▲Up To Search▲

Price & Availability of W83L951FG

	To Download W83L951FG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .