Part Number Hot Search : 
RT1P144S BZ5221 VTP8651 39109E3 PACUS U4065B PB0108SS TMP47C
Product Description
Full Text Search
 

To Download TTS3816B4E-7 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 M.tec
2M x 16Bit x 4 Banks synchronous DRAM
TTS3816B4E
GENERAL DESCRIPTION
The TTS3816B4E is 134,217,728 bits synchronous high data rate Dynamic RAM organized as 8 x 1,048,576 words by 16 bits, fabricated with M'tec high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth, high performance memory system applications.
FEATURES
* JEDEC standard 3.3V power supply * LVTTL compatible with multiplexed address * Four-banks operation * MRS cycle with address key programs -. CAS latency (2 & 3) -. Burst length (1, 2, 4, 8 & Full page) -. Burst type (Sequential & Interleave) * All inputs are sampled at the positive going edge of the system clock. * Burst read single-bit write operation * DQM for masking * Auto & self refresh * 64ms refresh period (4K cycle)
ORDERING INFORMATION
Part No. TTS3816B4E-7 TTS3816B4E-6 TTS3816B4E-6A TTS3816B4E-6B TTS3816B4E-6C TTS3816B4E-6D TTS3816B4E-6E Max Freq. 100MHz 2-2-2 133MHz 3-3-3 100MHz 2-3-3 133MHz 2-3-2 133MHz 2-2-2 150MHz 3-3-3 166MHz 3-3-3 LVTTL 54 TSOP(II) Interface Package
Revision_1.1
1
TwinMOS Technologies Inc.
Sep. 2000
M.tec
PIN CONFIGURATION (Top View)
TTS3816B4E
54Pin TSOP (II) (400mil x 875mil) (0.8 mm Pin pitch)
Revision_1.1
2
TwinMOS Technologies Inc.
Sep. 2000
M.tec
PIN FUNCTION DESCRIPTION
Pin Name
A0~ A11 BS0, BS1 DQ0 ~DQ15 /CS /RAS /CAS /WE UDQM/LDQM CLK CKE Vcc Vss Vcc Vss NC Address Bank Data Input / Output Chip Select Row Address Strobe Column Address Strobe Write Enable Input /output mask Clock Input Clock Enable Power (+3.3 V) Ground
TTS3816B4E
Function
Description
Multiplexed pins for row and column address Row address: A0 ~ A11. Column address: A0 ~ A8. Select bank to activate during row address latch time, or bank to read/write during address latch time. Multiplexed pins for data output and input. Disable or enable the command decoder. When command decoder is disabled, new command is ignored and previous operation continues. Command input. When sampled at the rising edge of the clock, /RAS, /CAS and /WE define the operation to be executed. Referred to /RAS Referred to /RAS The output buffer is placed at Hi-Z (with latency of 2) when DQM is sampled high in read cycle. In write cycle, sampling DQM high will block the write operation with zero latency. System clock used to sample inputs on the rising edge of clock. CKE controls the clock activation and deactivation. When CKE is low, Power Down mode, Suspend mode, or Self Refresh mode is entered. Power for input buffers and logic circuit inside DRAM. Ground for input buffers and logic circuit inside DRAM.
Q Power (+ 3.3 V) for I/O Separated power from VCC , used for output buffers to improve noise. buffer Q Ground for I/O buffer No Connection Separated ground from VSS , used for output buffers to improve noise. No connection
Revision_1.1
3
TwinMOS Technologies Inc. Sep. 2000
M.tec
BLOCK DIAGRAM
TTS3816B4E
Bank Select
Data Input
Sse AMP
Address
ADD
Buffer
Row Decoder &
Refresh Counter
2MX16 2MX16 2MX16 2MX16
Column Decoder
Output Buffer
DQ
Column Buffer /CS / RAS / CAS / WE CLK CKE Latency & Burst Length
Commend Decoder & Clock Buffer
Programming Register
Revision_1.1
4
TwinMOS Technologies Inc.
Sep. 2000
M.tec
ABSOLUTE MAXIMUM RATING
Parameter
Voltage on any pin relative to VSS Voltage on VCC supply relative to VSS Storage temperature Power dissipation Short circuit current
TTS3816B4E
Symbol
VIN, VOUT VCC, VCCQ TSTG PD IOS
Value
-1.0 ~ 4.6 -1.0 ~ 4.6 -55 ~ +150 1 50
Unit
V V W mA
Note:
Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to the recommended operating conditions. Exposure to higher voltage than recommended for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to VSS = 0V, TA = 0 to 70C)
Parameter
Supply voltage Input logic high voltage Input logic low voltage Output logic high voltage Output logic low voltage Input leakage current (Input) Input leakage current (I/O pins)
Symbol
VCC, VCCQ VIH VIL VOH VOL IIL IIL
Min
3.0 2.0 -0.3 2.4 -1 -1.5
Typ
3.3 3.0 0 -
Max
3.6 VCCQ+0.3 0.8 0.4 1 1.5
Unit
V V V V V uA uA
Note
1 2 IOH=-2mA IOL=2mA 3 3,4
Notes:
1. VIH (max) = 5.6V AC. The overshoot voltage duration is 3ns. 2. VIL (min) = -2.0V AC. The undershoot voltage duration is 3ns. 3. Any input 0V VIN VCCQ, Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs. 4. Dout is disabled, 0V Vout VCCQ
Revision_1.1
5
TwinMOS Technologies Inc.
Sep. 2000
M.tec
DC CHARACTERISTICS
(Recommended operating condition unless otherwise noted, TA = 0 to 70C)
TTS3816B4E
Parameter
Operating current (One bank active)
Symbol
Test Condition
Burst length = 1 tRCtRC(min) IOL = 0mA CKEVIL(max), tCC = 15 ns
TTS3816B4E
Unit
Note
ICC1
100
mA
1
ICC2P Pre-charge standby current in power- down mode ICC2PS
2 mA
CKE&CLKVIL(max), tCC = CKEVIH(min), /CSVIH(min) , tCC = 15ns Input signals are stable CKEVIH(min), CLKVIL(Max) , tCC = Input signals are stable CKEVIL(max), tCC = 15 ns
2
ICC2N Pre-charge standby current in non power-down mode ICC2NS
30 mA 10
ICC3P Active standby current in power-down mode ICC3PS
5 mA
CKE&CLKVIL(max), tCC = CKEVIH(min), /CSVIH(min) , tCC = 15ns Input signals are stable CKEVIH(min), CLKVIL(Max) , tCC = Input signals are stable IOL=0 mA Page burst 2Banks activated tCCD = 2CLKS tRCtRC(min) CL = 3 CL = 2
5
Active standby current in non power-down mode (One bank active)
ICC3N
40 mA 20 150 mA 140 mA 2 1
ICC3NS
Operating current (Burst mode)
ICC4
Refresh current
ICC5
160
Self refresh current
ICC6
CKE0.2V
1
mA
Note: 1.Measured with outputs open.
2.Refresh period is 64 ms.
Revision_1.1
6
TwinMOS Technologies Inc. Sep. 2000
M.tec
AC CHARACTERISTICS AND OPERATING (Vcc=3.3V0.3V, Ta=0 to 70C)
Parameter
Row active to row active delay /RAS to /RAS delay Row pre-charge time Row active time Row cycle time Col. Address to col. Address delay Write Recovery Time CLK Cycle Time CLK High Level width CLK Low Level width Access Time from CLK Output Data Hold Time Data-in Set-up Time Data-in Hold Time Address Set-up Time Address Hold Time CKE Set-up Time CKE Hold Time Command Set-up Time Command Hold Time Refresh Time Mode register Set Cycle Time
TTS3816B4E
Symbol
tRRD tRCD tRP tRAS tRC tCCD tWR tCK tCH tCL tAC tOH tDS tDH tAS tAH tCKS tCKH tCMS tCMH tREF tRSC CL=2 CL=3
-7
-6
-6A
-6B
-6C
-6D
-6E
Min Max Min Max Min Max Min Max Min Max Min Max Min Max 20 20 20 48 70 1 20
100K
Unit
ns ns ns
15 20 20 45
67.5
100K
20 30 30 48 70 1 20
1000 1000 100K
14 20 15 45 63 1 14
1000 1000 100K
14 15 15 45 63 1 14
1000 1000 100K
14 20 20 45 63 1 13
1000 1000 100K
12 18 18 42 60 1 12 1000 100K
ns ns CLK ns ns
1 15
1000 1000
CL=2 10 CL=3 8 3 3
10 7.5 2.5 2.5
10 8 3 3
7.5 7.5 2.5 2.5
7.5 7.5 2.5 2.5
6.5 2 2
6 2 2
1000
ns ns 5 ns ns ns ns ns ns ns ns ns ns 64 ms
6 6 3 2 1 2 1 2 1 2 1 64 20 15 2.7 1.5 1 1.5 1 1.5 1 1.5 1
6 5.4 3 2 1 2 1 2 1 2 1 64 20
8 6 2.7 1.5 1 1.5 1 1.5 1 1.5 1 64 14
5.4 5.4 2.7 1.5 1 1.5 1 1.5 1 1.5 1 64 14
5.4 5.4 2.5 1.5 1 1.5 1 1.5 1 1.5 1 64 12
5.4 2 1.5 1 1.5 1 1.5 1 1.5 1 64 12
ns
Revision_1.1
7
TwinMOS Technologies Inc. Sep. 2000
M.tec
54PIN PLASTIC TSOP(II) (400mil)
54 28
TTS3816B4E
detail of lead end
F P
E 1 2 A H G I 7
J
C D
NOTE
N
M
L K B
ITEM A B C D E F G H I J K L M N P MILLIMETERS 22.62 MAX. 0.91 MAX. 0.80 (T.P.) 0.32 +0.08 -0.07 0.100.05 1.20 MAX. 1.00 11.760.20 10.160.10 0.800.20 0.145 +0.025 -0.015 0.500.10 0.13 0.10 3 +7 -3 INCHES 0.891 MAX. 0.036 MAX. 0.031 (T.P.) 0.0130.003 0.0040.002 0.048 MAX. 0.039 0.4630.008 0.4000.004 0.031 +0.009 -0.008 0.0060.001 0.020 +0.004 -0.005 0.005 0.004 3 +7 -3
M
Each lead centerline is located within 0.13 mm (0.005 inch) of its true position (T.P.) at maximum material condition.
Revision_1.1
8
TwinMOS Technologies Inc.
Sep. 2000


▲Up To Search▲   

 
Price & Availability of TTS3816B4E-7

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X