Part Number Hot Search : 
02584 TS3843B 1N4959D TS3843B LL5221 UMTS125 PG2017 SFD342
Product Description
Full Text Search
 

To Download TS79M24CZ Datasheet File
  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
　
 

  Datasheet File OCR Text:
 TS79M00 series
3-Terminal Medium Current Negative Voltage Regulator
Pin assignment: 1. Ground 2. Input 3. Output (Heatsink surface connected to Pin 2)
Voltage Range - 5V to - 24V Output Current up to 0.5A
General Description
The TS79M00 Series negative voltage regulators are identical to the popular TS7900 Series devices, except that they are specified for only half the output current. Like the TS7900 devices, the TS79M00 Series 3-Terminal regulators are intended for local, on-card voltage regulation. Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions. Maximum output current with adequate heatsink is 500mA This series is offered in 3-pin TO-220, TO-252 package.
Features
Output current up to 0.5A No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 4% tolerance
Standard Application
Ordering Information
Part No.
TS79MxxCZ TS79MxxCP
Operating Temp.
-20 ~ +125 C
o
Package
TO-220 TO-252
Note: Where xx denotes voltage option.
A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response.
Absolute Maximum Rating
Input Voltage Input Voltage Power Dissipation TO-220 TO-220 TO-252 Operating Junction Temperature Range Storage Temperature Range Note : * TS79M05 to TS79M18 ** TS79M24 *** Follow the derating curve Vin * Vin ** Without heatsink Pt *** Without heatsink TJ TSTG - 35 - 40 2 15 1 -20 ~ +125 -65 ~ +150
o o
V V
W
C C
TS79M00 series
1-7
2003/12 rev. A
TS79M05 Electrical Characteristics
(Vin= -10V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output voltage
Symbol
o
Test Conditions
Tj=25 C -7.5VVin -20V, 5mAIout350mA, PD5W -7.5VVin -25V, Io=200mA 5mAIout500mA 5mAIout200mA
o
Min
- 4.80 - 4.75 -------
Typ
-5 -5 3 20 10 4 --40 66 2 0.7 -0.2
Max
- 5.20 - 5.25 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGline REGload Iq Iq Vn RR Vdrop Io peak Vout/ Tj
Tj=25 oC Tj=25 C
o
mV 100 50 8 0.5 0.5 -----uV dB V A mV/
o
Iout=0, Tj=25 C -7.5VVin -25V 5mAIout350mA 10Hzf100KHz, Tj=25 C f=120Hz, -8VVin -18V Iout=350mA, Tj=25 oC Tj=25 C Iout=5mA, 0 CTj125 C
o o o o
mA
-54 ----
C
TS79M06 Electrical Characteristics
(Vin= -11V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -8.5VVin -21V, 5mAIout350mA, PD5W -8.5VVin -25V, Io=200mA 5mAIout500A 5mAIout200mA
Min
- 5.75 - 6.3 -------
Typ
-6 -6 3 20 10 4 --40 66 2 0.7
Max
- 6.25 - 6.3 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of
REGline REGload Iq Iq Vn RR Vdrop Io peak
Tj=25 C Tj=25 oC
o
mV 120 60 8 0.5 0.5 ----uV dB V A mV/
o
Iout=0, Tj=25 oC -8.5VVin -25V 5mAIout350mA 10Hzf100KHz, Tj=25 C f=120Hz, -9VVin -19V Iout=350mA, Tj=25 C Tj=25 C
o o o o o
mA
-54 ---
Vout/ Tj Iout=5mA, 0 CTj125 C --0.2 -Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
C
TS79M00 series
2-7
2003/12 rev. A
TS79M08 Electrical Characteristics
(Vin= -14V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -10.5VVin -23V, 5mAIout350mA, PD5W -10.5VVin -25V, Io=200mA 5mAIout500mA 5mAIout200mA
o
Min
- 7.69 - 7.61 -------
Typ
-8 -8 6 25 10 4 --60 63 2 0.7 -0.4
Max
- 8.32 - 8.40 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGline REGload Iq Iq Vn RR Vdrop Io peak Vout/ Tj
Tj=25 oC Tj=25 C
o
mV 160 80 8 0.5 0.5 -----uV dB V A mV/
o
Iout=0, Tj=25 C -10.5VVin -25V 5mAIout350mA 10Hzf100KHz, Tj=25 C f=120Hz, -11VVin -21V Iout=350mA, Tj=25 oC Tj=25 C Iout=5mA, 0 CTj125 C
o o o o
mA
-54 ----
C
TS79M09 Electrical Characteristics
(Vin= -15V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -11.5VVin -23V, 5mAIout350mA, PD5W -11.5VVin -26V Io=200mA 5mAIout500mA 5mAIout200mA
Min
- 8.65 - 8.57 -------
Typ
-9 -9 6 25 10 4 --60 63 2 0.7
Max
- 9.36 - 9.45 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of
REGline REGload Iq Iq Vn RR Vdrop Io peak
Tj=25 C Tj=25 oC
o
mV 180 90 8 0.5 0.5 ----uV dB V A mV/
o
Iout=0, Tj=25 oC -11.5VVin -26V 5mAIout350mA 10Hzf100KHz, Tj=25 C f=120Hz, -12VVin -22V Iout=350mA, Tj=25 C Tj=25 C
o o o o o
mA
-54 ---
Vout/ Tj Iout=5mA, 0 CTj125 C --0.4 -Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
C
TS79M00 series
3-7
2003/12 rev. A
TS79M12 Electrical Characteristics
(Vin= -19V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -14.5VVin -27V, 5mAIout350mA, PD 5W -14.5VVin -30V, Io=200mA 5mAIout500mA 0mAIout200mA
Min
- 11.53 - 11.42 -------
Typ
- 12 - 12 8 25 10 4 --70 60 2 0.7 -0.8
Max
- 12.48 - 12.60 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGline REGload Iq Iq Vn RR Vdrop Io peak Vout/ Tj
Tj=25 oC Tj=25 C
o o
mV 240 120 8 0.5 0.5 -----uV dB V A mV/
o
Tj=25 C, Iout=0 -14.5VVin -30V 5mAIout200mA 10Hzf100KHz, Tj=25 C f=120Hz, -15VVin -25V Iout=350mA, Tj=25 oC Tj=25 C Iout=5mA, 0 CTj125 C
o o o o
mA
-54 ----
C
TS79M15 Electrical Characteristics
(Vin= -23V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Tj=25 C Output Voltage Vout
o
Test Conditions
-17.5VVin -30V, 5mAIout350mA, PD 5W Tj=25
o
Min
- 14.42 - 14.28 -------
Typ
- 15 - 15 8 25 10 5 --90 60 2 0.7
Max
- 15.60 - 15.75 50
Unit
V
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of
REGline REGload Iq Iq Vn RR Vdrop Io peak
-17.5VVin -30V, Io=200mA 5mAIout500mA 5mAIout200mA
C C
mV 300 150 8 0.5 0.5 ----uV dB V A mV/
o
Tj=25
o
Tj=25 oC, Iout=0 -17.5VVin -30V 5mAIout350mA 10Hzf100KHz, Tj=25 C f=120Hz, -18VVin -28V Iout=350mA, Tj=25 C Tj=25 C
o o o o o
mA
-54 ---
Vout/ Tj Iout=5mA, 0 CTj125 C --1.0 -Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
C
TS79M00 series
4-7
2003/12 rev. A
TS79M18 Electrical Characteristics
(Vin= -27V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -21VVin -33V, 5mAIout350mA, PD 5W -21VVin -33V, Io=200mA 5mAIout500mA 5mAIout200mA
Min
- 17.30 - 17.14 -------
Typ
- 18 - 18 8 25 10 5 --110 60 2 0.7 -1.0
Max
- 18.72 - 18.90 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage
REGline REGload Iq Iq Vn RR Vdrop Io peak Vout/ Tj
Tj=25 oC Tj=25 C
o o
mV 360 180 8 0.5 0.5 -----uV dB V A mV/
o
Tj=25 C, Iout=0 -21VVin -33V 5mAIout350nA 10Hzf100KHz, Tj=25 C f=120Hz, -21VVin -31V Iout=350mA, Tj=25 oC Tj=25 C Iout=5mA, 0 CTj125 C
o o o o
mA
-54 ----
C
TS79M24 Electrical Characteristics
(Vin=- 33V, Iout=350mA, 0 CTj125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
o o
Parameter
Output Voltage
Symbol
o
Test Conditions
Tj=25 C -27VVin -38V, 5mAIout350mA, PD 5W -27VVin -38V, Io=200mA 5mAIout500mA 5mAIout200mA
Min
- 23.07 - 22.85 -------
Typ
- 24 - 24 10 30 10 5 --170 60 2 0.7
Max
- 24.96 - 25.20 50
Unit
V
Vout
Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of
REGline REGload Iq Iq Vn RR Vdrop Io peak
Tj=25 C Tj=25 oC
o
mV 480 240 9 0.5 0.5 ----uV dB V A mV/
o
Iout=0, Tj=25 oC -27VVin -38V 5mAIout350mA 10Hzf100KHz, Tj=25 C f=120Hz, -27VVin -37V Iout=350mA, Tj=25 C Tj=25 C
o o o o o
mA
-50 ---
Vout/ Tj Iout=5mA, 0 CTj125 C --1.0 -Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings.
C
TS79M00 series
5-7
2003/12 rev. A
Electrical Characteristics Curve
FIGURE 1 - Worst Case Power Dissipation v.s. Ambient Temperature FIGURE 2 - Peak Output Current v.s. Dropout Voltage
FIGURE 3 - Quiescent Current v.s. Input Voltage
FIGURE 4 -Dropout Voltage v.s. Junction Temperature
FIGURE 5 - Quiescent Current v.s. Output Current
FIGURE 6 - TO-252 Thermal Resistance and Pd(max) v.s. P.C.B Copper Length
TS79M00 series
6-7
2003/12 rev. A
TO-220 Mechanical Drawing
A
B
C
K L
DIM
TO-220 DIMENSION MILLIMETERS MIN MAX 10.000 3.240 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 10.500 4.440 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 INCHES MIN MAX 0.394 0.128 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 0.413 0.175 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270
P
A B C D
J I
M
E F G H I J K L M N
D H F G E
O N
J A E F I B G D C H
TS79M00 series 7-7
O P
TO-252 Mechanical Drawing
TO-252 DIMENSION DIM A B C D E F G H I J MILLIMETERS MIN MAX 6.570 9.250 0.550 2.560 2.300 0.490 1.460 0.520 5.340 1.460 6.840 10.400 0.700 2.670 2.390 0.570 1.580 0.570 5.550 1.640 INCHES MIN MAX 0.259 0.364 0.022 0.101 0.090 0.019 0.057 0.020 0.210 0.057 0.269 0.409 0.028 0.105 0.094 0.022 0.062 0.022 0.219 0.065
2003/12 rev. A


▲Up To Search▲   

 
Price & Availability of TS79M24CZ

All Rights Reserved © IC-ON-LINE 2003 - 2022  
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]
 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X