|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
e5130 Low Voltage CMOS Driver Circuit Description The e5130 contains 4 independent driver outputs with an ON resistance of typ. 25 W (15 W) tor the P-channel output transistors and typ. 20 W (13 W) for the N-channel output transistors; at a supply voltage of 1.5 V (3 V). To obtain a fast transition of the outputs, even for slow rise/-fall time input signals, all digital inputs (IN1 ... IN4) have a schmitt-trigger characteristic; with a hysteresis of typ. 50 mV. If a higher driving capability is needed, all inputs and outputs may be connected in parallel. In this case the rise/-fall time of the input signals IN1 ... IN4 must be less than 200 nsec. Due to the fast switching characteristic of the tristatable output drivers, the circuit is also suited as low voltage bus driver. Features D 1.1 - 3.6 V operating voltage range D 4 non-inverting, tristatable drivers for the following applications: - Motor driver for bipolar stepper motors in watch/clock applications - Driver for piezoelectric transducers (buzzer) - LED Driver - Line driver for medium speed applications Advantages D High load current at low supply voltage D Replaces several discrete transistors D Tri-state operation possible D Possible applications: - Motor driver - Radio controlled clock/watch - Line driver for mini-computer, laptop - LED driver - Relay driver Pad Configuration OUT1 OUT2 OUT3 OUT4 VDD VSS VDD IN1 ... IN4 TRI Name Description Positive supply voltage Negative supply voltage Digital inputs Tristate input Drive outputs e5130 TRI 94 8178 OUT1 ... OUT4 Chipsize: x = 1.08 mm, y = 1.42 mm, Padwindow: 90 x 90 m IN1 IN2 IN3 IN4 VSS Ordering Information Extended Type Number E5130A-DIT Die Package Die in Trays Remarks Rev. A2, 13-Mar-01 1 (4) e5130 Absolute Maximum Ratings Absolute maximum ratings define parameter limits which, it exceeded, may permanently change or damage the device. All inputs and outputs on circuits are highly protected against electrostatic discharges. However, precautions to minimize build-up of electrostatic charges during handling are recommended. The circuits are protected against supply voltage reversal for typically 5 minutes, if the current is limited to 120 mA. Parameters Supply voltage Input voltage range, all inputs Operating ambient temperature range Storage temperature range Lead temperature during soldering at 2 mm distance, 10 s Symbol VDD - VSS VI Value - 0.3 to + 5 VSS - 0.3 to VDD + 0.3 - 20 to + 70 - 40 to + 125 260 Unit V V C C C Operating Characteristics VSS = 0 V, VDD = + 1.5 V, Tamb = + 25 C, unless otherwise specified. All voltage levels are measured with reference to VSS. Parameters Operating voltage Operating temperature Operating current (standby) VDD = 3.6 V, RL12 = RL34 = R, IN1 to IN4 at VDD or VSS, TRI at VSS Drive output OUT1 to OUT4 Output current Output current Output current Delay time Delay time Rise/-fall time Rise/-fall time Digital input IN1 to IN4 Input current Input current Threshold Hysteresis Tristate input TRI Input current TRI VIH = VDD IIH 0.15 0.4 1.2 mA VIL = 0 V VIH = VDD V mV IIL IIH VTH VHYST VDD/2 50 -100 100 nA nA V mV VDD = 1.2 V, RL12 = RL34 = 200 W VDD = 1.5 V, RL12 = RL34 = 200 W VDD = 3.0 V, RL12 = RL34 = 200 W VDD = 3 V, CL = 50 pF VDD = 1.5 V, CL = 50 pF, see figure 2, note 1 VDD = 3 V, CL = 50 pF VDD = 1.5 V, CL = 50 pF, see figure 2, note 2 IOUT IOUT IOUT TDr, TDf TDr, TDf tr, tf tr, tf " 4.3 " 5.7 " 12 " 4.75 " 6.20 " 13 35 80 8 12 60 150 15 25 mA mA mA ns ns ns ns Test Conditions / Pin Symbol VDD Tamb IDD Min 1.1 - 10 0.05 Typ Max 3.6 60 1 Unit V C mA 2 (4) Rev. A2, 13-Mar-01 e5130 RL12 RL34 15 VDD TRI IN1 e5130 IN2 IN3 IN4 VSS 94 8179 I RL ( mA ) OUT1 OUT2 OUT3 OUT4 10 5 0 1.0 94 8192 1.5 2.0 VDD ( V ) 2.5 3.0 Figure 1. Test circuit 94 8181 Figure 3. Typical current into 200 W load resistor, condition as per figure 1 50 IN1...4 tr tf RON ( W ) 40 P-CH Transistor 30 OUT1...4 tDr Figure 2. 20 10 0 1.0 1.5 2.0 VDD ( V ) 2.5 3.0 N-CH Transistor tDf Note 1: tDr, tDf is defined at 50% of supply voltage Note 2: tr, tf is defined from 10% to 90%, resp. 90% to 10% of supply voltage 94 8193 Figure 4. Typical output on-resistance vs. supply voltage at VDS = 0.2 V 0 1014.0 851.0 118.0 366.0 534.0 782.0 1014.0 447.5 e5130 0 10 0 221.0 389.0 610.0 778.0 0 94 8180 Figure 5. Pad coordinates Rev. A2, 13-Mar-01 3 (4) e5130 Application Circuit Line Driver Micro-Motor or Stepper Motor M Load 4.8 mA @ 1.5 V 12 mA @ 3.0 V OUT1 OUT2 OUT3 OUT4 VDD TRI e5130 IN2 IN3 IN4 VSS from logic or mP IN1 We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Atmel Wireless & Microcontrollers products for any unintended or unauthorized application, the buyer shall indemnify Atmel Wireless & Microcontrollers against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Data sheets can also be retrieved from the Internet: http://www.atmel-wm.com Atmel Germany GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2594, Fax number: 49 (0)7131 67 2423 4 (4) Rev. A2, 13-Mar-01 |
Price & Availability of E5130A-DIT |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |