|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Advance Product Information April 28, 2003 Ka Band 2W Power Amplifier Key Features * * * * * * * * TGA4514-EPU Typical Frequency Range: 31 - 35 GHz 33.5 dBm Nominal Psat @ Vd = 7V 31.5 dBm Nominal P1dB IMD3: 31dBc at Pout/tone=22dBm 19 dB Nominal Gain Bias 6 - 7 V, 1150 mA 0.25 um 2MI pHEMT Technology Chip Dimensions 4.0 x 3.2 x 0.1 mm (0.161 x 0.128 x 0.004) in Preliminary Measured Data 30 Gain & Return Loss (dB ) 20 10 0 -10 -20 -30 28 29 30 31 32 33 34 35 36 37 38 Frequency (GHz) Bias Conditions: Vd = 6 V, Id = 1150 mA Primary Applications * * * Point-to-Point Radio Military Radar Systems Ka Band Sat-Com GAIN ORL IRL 35 Psat @ Pin= 20dBm (dBm) 34 33 32 31 30 29 28 30 Bias Conditions: Vd = 6/7 V, Id = 1150 mA Vd = 7 V Vd = 6 V 31 32 33 34 35 Frequency (GHz) 36 37 Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 1 Advance Product Information April 28, 2003 TGA4514-EPU TABLE I MAXIMUM RATINGS 1/ SYMBOL Vd Vg Id 1/2Ig1/2 PIN PD T CH TM TSTG 1/ 2/ 3/ 4/ 5/ Drain Voltage Gate Voltage Range Drain Current Gate Current Input Continuous Wave Power Power Dissipation Operating Channel Temperature Mounting Temperature (30 Seconds) Storage Temperature PARAMETER VALUE 8V -5 TO 0 V 2.5 A 70 mA 27 dBm TBD 150 C 320 C -65 to 150 C 0 0 0 NOTES 2/ 2/ 3/ 3/ 2/ 4/ 5/ 6/ These ratings represent the maximum operable values for this device. Combinations of supply voltage, supply current, input power, and output power shall not exceed PD. Total current for the entire MMIC. When operated at this bias condition with a base plate temperature of TBD, the median life is reduced from TBD to TBD hrs. Junction operating temperature will directly affect the device median time to failure (MTTF). For maximum life, it is recommended that junction temperatures be maintained at the lowest possible levels. These ratings apply to each individual FET. 6/ Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 2 Advance Product Information April 28, 2003 TGA4514-EPU TABLE II DC PROBE TESTS (Ta = 25 0C, Nominal) SYMBOL IDSS,Q1 G M,Q1 V BVGS,Q1-Q6 V BVGD,Q1-Q6 V P,Q1-Q6 PARAMETER Saturated Drain Current Transconductance Breakdown Voltage gate-source Breakdown Voltage gate-drain Pinch-off Voltage MIN. TYP. 114 150 -16 -16 -1 MAX. UNITS mA mS V V V Q1- Q4 are 400 um FETs, Q5 is 3200 um FET, Q6 is 4000 um FET TABLE III ELECTRICAL CHARACTERISTICS (Ta = 25 0C, Nominal) PAR AM E TE R Frequenc y R ange D rain Voltage, Vd D rain C urrent, Id G ate V oltage, V g Sm all S ignal G ain, S 21 Input R eturn Loss, S11 O utput R eturn Loss, S22 O utput Pow er @ 1 dB C om pression G ain, P1dB Saturated Pow er @ P in = 20 dBm , Psat IM D 3, Freq = 33 G H z, P out/T one = 22 dBm TYPIC AL 31 - 35 6 1150 -0.5 19 -7 -10 31.5 32.5 31 UNITS GHz V mA V dB dB dB dBm dBm dBc Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 3 Advance Product Information April 28, 2003 Preliminary Measured Data 22 Bias Conditions: Vd = 6 V, Id = 1150 mA, Room Temp. TGA4514-EPU 20 18 Gain (dB) 16 14 12 10 28 29 30 31 32 33 34 35 36 37 38 Fre que ncy (GHz) Bias Conditions: Vd = 6/7 V, Id = 1150 mA, Room Temp. 35 34 Psat @ Pin = 20dBm (dBm) 33 32 31 30 29 28 30 31 Vd = 7 V Vd = 6 V 32 33 34 35 36 37 Frequency (GHz) Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 4 Advance Product Information April 28, 2003 Preliminary Measured Data Bias Conditions: Vd = 6 V, Id = 1150 mA, Room Temp. TGA4514-EPU 0 -5 -10 -15 -20 -25 -30 -35 28 29 30 31 32 33 34 35 36 37 38 Fre que ncy (GHz) 0 -5 O utput Return Loss (dB) -10 -15 -20 -25 -30 -35 28 29 30 31 32 33 34 35 36 37 38 Fre que ncy (GHz) Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice Input Return Loss (dB) TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 5 Advance Product Information April 28, 2003 Preliminary Measured Data 35 34 33 32 Pout (dBm) 31 30 29 28 27 26 25 30 31 32 33 Freque ncy (GHz) 34 35 Bias Conditions: Vd = 6 V, Id = 1150 mA, Room Temp. TGA4514-EPU Psat @ Pin=20dBm P1dB 36 35 34 33 32 Pout (dBm ) 31 30 29 28 27 26 25 31 Bias Conditions: Vd = 7 V, Id = 1150 mA, Room Temp. Psat @ Pin=20dBm P1dB 32 33 34 Frequency (GHz) 35 36 37 Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 6 Advance Product Information April 28, 2003 TGA4514-EPU Preliminary Measured Data Bias Conditions: Vd = 6 V, Id = 1150 mA, Freq = 33 GHz, Room Temp. 35 30 25 20 15 10 5 0 -5 -3 -1 1 3 5 7 9 11 13 15 17 19 21 23 Pin (dBm) 1600 Pout Pout (dBm) & Power Gain (dB) 1400 1200 Id (mA) 7 Id 1000 Gain 800 600 400 200 Bias Conditions: Vd = 6 V, Id = 1150 mA, Freq = 33 GHz, Room Temp. 60 50 40 IMD3 (dBc) 30 20 10 0 6 8 10 12 14 16 18 20 22 24 26 28 30 Pout pe r tone (dBm) Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com Advance Product Information April 28, 2003 TGA4514-EPU Preliminary Measured Data Bias Conditions: Vd = 6 V, Id = 920 mA 25 20 -40 0C +25 0C +85 0C 15 Gain (dB) 10 5 0 -5 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Fre quency (GHz) Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 8 Advance Product Information April 28, 2003 TGA4514-EPU Mechanical Drawing GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 9 Advance Product Information April 28, 2003 TGA4514-EPU Chip Assembly Diagram Note: Apply bias for Vd on both sides. Bias may be applied for Vg from either side. GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 10 Advance Product Information April 28, 2003 TGA4508-EPU Assembly Process Notes Reflow process assembly notes: * * * * * Use AuSn (80/20) solder with limited exposure to temperatures at or above 300C (30 seconds max). An alloy station or conveyor furnace with reducing atmosphere should be used. No fluxes should be utilized. Coefficient of thermal expansion matching is critical for long-term reliability. Devices must be stored in a dry nitrogen atmosphere. Component placement and adhesive attachment assembly notes: * * * * * * * Vacuum pencils and/or vacuum collets are the preferred method of pick up. Air bridges must be avoided during placement. The force impact is critical during auto placement. Organic attachment can be used in low-power applications. Curing should be done in a convection oven; proper exhaust is a safety concern. Microwave or radiant curing should not be used because of differential heating. Coefficient of thermal expansion matching is critical. Interconnect process assembly notes: * * * * Thermosonic ball bonding is the preferred interconnect technique. Force, time, and ultrasonics are critical parameters. Aluminum wire should not be used. Maximum stage temperature is 200C. GaAs MMIC devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. Note: Devices designated as EPU are typically early in their characterization process prior to finalizing all electrical and process specifications. Specifications are subject to change without notice TriQuint Semiconductor Texas: Phone (972)994-8465 Fax (972)994 8504 Web: www.triquint.com 11 |
Price & Availability of TGA4514-EPU |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |