![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Ordering number : ENA0294 LB8682PL Overview Monolithic Digital IC For Camera Cell Phone Motor Driver Two Saturated Drive Channels and One Constant-Current Drive Channel The LB8682PL is a motor driver IC that has a two saturated drive channels and one constant-current drive channel. Its compact, low-profile package makes it ideal for use in cell phone cameras. Using direct microcontroller drive, and the control of the shutter and the motor for the AF(Auto-Focus) drive, etc.. Functions * Constant voltage control for AF (H-Bridge x 2ch) * Constant current control for shutter. (H-Bridge x 1ch) * Built-in thermal protection circuit * Built-in reference voltage circuit (0.2V typical) * Built-in spark killer diodes Specifications Absolute Maximum Ratings at Ta = 25C Parameter Maximum supply voltage Output voltage Input voltage GND pin source current Allowable power dissipation Operating temperature Storage temperature Symbol VCC max VOUT max VIN max IGND Pd max Topr Tstg 3 Conditions Ratings -0.3 to +0.8 Unit V V V mA mW C C OUT1 to OUT6 ENA1 to ENA2, IN1 to IN4 Per channel When mounted on a circuit board* VCC+VSF -0.3 to +0.8 300 830 -20 to +75 -40 to +125 *: On the specified circuit board (40.0x50.0x0.8mm four-layer glass-epoxy board) Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. 31407 MS OT 20051221-S00001 No.A0294-1/5 LB8682PL Allowable Operating Ranges at Ta = 25C Parameter Supply voltage Constant-current setting range High-level input voltage Low-level input voltage Symbol VCC IOUT VIH VIL ENA1 to ENA2, IN1 to IN4 Conditions Ratings 2.2 to 7.5 50 to 200 1.5 to 7.5 -0.3 to +0.5 Unit V mA V V Electrical Characteristics at Ta = 25C, VCC = 3.3V Parameter Current drain Symbol ICC0 ICC1 ICC2 Input current IIN Conditions min ENA1 = ENA2 = IN3 = IN4 = 0V ENA1 = ENA2 = 3V IN3orIN4 = 3V IO = 200mA RF = 1 VIN = 3V Ratings typ 0.1 13.5 5.0 60 max 1 20.0 8.5 90 A mA mA A Unit Saturated drive driver (OUT1, OUT2, OUT3, and OUT4) Output saturation voltage1 VSAT11 VSAT12 Constant-Current drive driver (OUT5 and OUT6) Constant-current output1 Constant-current output2 Output saturation voltage IOUT1 IOUT2 VSAT21 VSAT22 Spark killer diode Reverse current Forward voltage Other circuits Thermal protection detection temperature TTSD (Design specification) 160 180 200 C IS (leak) VSF IOUT = 200mA 1 1.7 A V Between RFG and ground: 2 Between RFG and ground: 0.8, VCC = 5V IOUT = 100mA IOUT = 200mA 95 238 100 250 0.18 0.35 105 262 0.27 0.53 mA mA V V IOUT = 100mA IOUT = 200mA 0.22 0.42 0.32 0.62 V V Package Dimensions unit : mm 3321 TOP VIEW 3.5 13 12 BOTTOM VIEW Pin Assignment SGND RFG1 RFG2 VCC (NC) (NC) 18 0.35 17 16 15 14 13 12 IN4 11 IN3 10 IN2 9 8 7 ENA2 IN1 ENA1 0.35 18 19 OUT6 19 OUT5 20 3.5 0.4 0.75 24 7 6 0.2 1 OUT4 21 OUT3 22 OUT2 23 0.75 0.0NOM 0.85MAX TOP VIEW OUT1 24 1 PGND SANYO : VQLP24(3.5X3.5) 2 (NC) 3 VCC 4 (NC) 5 (NC) 6 (NC) No.A0294-2/5 Top view LB8682PL Block Diagram 1F VCC VCC OUT1 Logic and control block Stepping Motor OUT2 60k 80k ENA1 60k IN1 80k OUT3 Logic and control block 60k ENA2 CPU 80k Logic block OUT4 60k 80k IN2 Thermal shutdoun circuit 60k 80k VCC OUT5 RL IN3 0.2V Reference voltage Constant current control amplifier OUT6 4700pF 60k 80k IN4 S-GND P-GND RFG2 RFG1 RF This capacitor may be required depending on the mechanical shutter used. Usage Notes * The constant-current level is set with the resistor RF. The formula for calculating the current is shown below. Constant-current level = 0.2 / RF * Connect capacitors between VCC and ground to reduce the amount of motor noise that enters the power supply. No.A0294-3/5 LB8682PL Truth Table Input ENA1 Low High IN1 * Low High High Low High Low Low High High Low High Low High ENA2 Low IN2 * IN3 IN4 OUT1 OFF High Low OUT2 OFF Low High High Low Low High OFF Low High OFF OFF Constant High Low OFF current Standby Forward Reverse OFF Output OUT3 OFF OUT4 OFF Saturated OUT5 OUT6 Mode Standby *: don't care, OFF: hi-impedance. Timing Chart ENA IN1 IN2 IN3 IN4 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 * The waveforms shown for OUT1 to OUT4 are for a 2-phase excitation stepping motor driver. * In the constant-current driver waveforms for OUT5 and OUT6, the high-side transistor is saturated and the low-side transistor is not saturated. * The broken lines in the figure represent the off state. No.A0294-4/5 LB8682PL SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of March, 2007. Specifications and information herein are subject to change without notice. PS No.A0294-5/5 |
Price & Availability of LB8682PL
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |