 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Micrel, Inc. PROTOCOL TRANSPARENT 3.3V 10MHz to 729MHz FRACTIONAL-N SYNTHESIZER DESCRIPTION SY87739L SY87739L FEATURES Protocol transparent fractional-N synthesizer from 10MHz to 729MHz from a single 27MHz reference oscillator Generates exactly the correct frequency for common transport protocols with or without FEC Directly enables SY87721L CDR to lock onto any data rate within its range Exceeds BellCore and ITU jitter generation specifications Programmable via MicroWireTM interface Available in 32-Pin EPAD-TQFP package APPLICATIONS Metro access system Transponders Multiplexers: access, Add Drop Mux SONET/SDH/ATM-based transmission systems, modules and test equipment Broadband cross-connects Fiber optic test equipment Protocols supported: OC-1, OC-3, OC-12, OC-48, ATM, Gigabit Ethernet, Fast Ethernet, Fibre Channel, 2X Fibre Channel, 1394, InfiniBand, Proprietary Optical Transport The SY87739L is a complete rate independent frequency synthesizer integrated circuit. From a single reference source, this device generates a differential PECL output frequency from 10MHz up to 729MHz. The SY87739L generates an exactly correct reference frequency for common data transport protocols. This is especially important in transponder applications, where a standards compliant protocol data unit must be generated downstream, even in the absence of any signal from the associated upstream interface. In addition, the SY87739L will generate exactly correct reference frequencies for common data transport protocols augmented by forward error correction codes. The SY87739L accepts configuration via a MicroWireTM interface. For proprietary applications, the SY87739L generates reference frequencies guaranteed to enable the SY87721L CDR to lock to any possible baud rate from 28Mbps to 2.7Gbps. TYPICAL APPLICATIONS CIRCUIT 0.1F 2k 31 30 TYPICAL PERFORMANCE 0.1F 2k 26 25 FNVCF+ FNVCF- WRVCF+ WRVCF- Cycle-to-Cycle Jitter vs. Frequency 6 5 22 21 VCC 14 Saronix SEL-2431C 27.0000MHz 7 8 3 4 REFCLK+ REFCLKSY87739L CLKOUT+ CLKOUT- RMS JITTER (ps) 4 3 2 1 0 0 100 200 300 400 500 600 700 800 OUTPUT FREQUENCY (MHz) 1 121 121 PROGCS PROGDI PROGSK LOCKED 121 121 VCC 10, 25, 32 1, 9, 17, 18, 24 6 7 8 14 Microcontroller AnyClock and AnyRate are registered trademarks of Micrel, Inc. MicroWire is a trademark of National Semiconductor. M9999-111406 hbwhelp@micrel.com or (408) 955-1690 Rev.: D Amendment: /0 OUT OUT OUT IN 1 Issue Date: November 2006 Micrel, Inc. SY87739L PACKAGE/ORDERING INFORMATION GNDA FNVCF+ FNVCFNC NC WRVCF+ WRVCFGNDA Ordering Information(1) Part Number 24 23 22 21 20 19 18 17 VCCA NC CLKOUT+ CLKOUTNC NC VCCO VCC 32 31 30 29 28 27 26 25 VCCA NC REFCLK+ REFCLKNC PROGCS PROGDI PROGSK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Package Type H32-2 H32-2 H32-2 H32-2 Operating Range Industrial Industrial Industrial Industrial Package Marking SY87739LHI SY87739LHI SY87739LHY with Pb-Free bar line indicator SY87739LHY with Pb-Free bar line indicator Lead Finish Sn-Pb Sn-Pb Matte-Sn Pb-Free Matte-Sn Pb-Free SY87739LHI SY87739LHITR(2) SY87739LHY SY87739LHYTR(2, 3) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. EPAD-TQFP (H32-2) PIN DESCRIPTION Pin Number 1, 24 2, 5, 11, 12, 13, 15, 16, 19, 20 23, 28, 29 3, 4 Pin Name VCCA NC Pin Function Analog Supply (Power). Set to same voltage as VCC. No Connect. These pins are to be left unconnected. VCC GND NC NC NC LOCKED NC NC REFCLK Reference Clock Input (Differential PECL Input): This is a clock derived from an oscillator or other sufficiently accurate frequency source. The frequency provided at this input determines, along with the programming, the output frequency at REFOUT. Micrel recommends using a 27.000MHz frequency source. Program Interface Chip Select (TTL Input): This signal forms part of the MicroWireTM interface. When active high, this signal permits the acquisition of serial data. A falling edge on this input causes SY87739L to re-acquire lock to a new frequency, based on the program downloaded to it. Program Interface Data In (TTL Input): One data bit is sampled on each rising edge of PRGSK, while PROGCS is active high. Program Interface Serial Clock (TTL Input): One bit of configuration data is read in each clock cycle. Supply (Power): +3.15V to +3.45V. Ground. Lock Output (TTL Output): This indicates proper operation of all the blocks in the clock synthesis chain. Logic high indicates that SY87739L is generating the expected frequency at the CLKOUT output. Logic low indicates that one or more PLL in the clock synthesis chain has yet to achieve proper lock. Output Supply (Power). Set to same voltage as VCC. Reference Clock Output (Differential PECL Output): This is the synthesized clock generated from REFCLK. It can be used to supply a reference clock to a data recovery device, such as Micrel's SY87721L. Analog Ground. Wrapper Filter (Analog I/O): These pins connect to the output from the wrapper synthesizer charge pump, as well as the input to the corresponding VCO. A filter network, as described below, converts the charge pump current to a voltage, and adjusts loop bandwidth. Fractional-N Filter (Analog I/O): These pins connect to the output from the fractional-N synthesizer charge pump, as well as the input to the corresponding Voltage Controlled Oscillator (VCO). A filter network, as described below, converts the charge pump current to a voltage, and adjusts loop bandwidth. 2 6 PROGCS 7 8 9, 17, 10 14 PROGDI PROGSK VCC GND LOCKED 18 21, 22 VCCO CLKOUT 25, 32 26, 27 GNDA WRVCF 30, 31 FNVCF M9999-111406 hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY87739L Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) .................................. -0.5V to +5.0V Input Voltage(VIN) ...................................... -0.5V to VCC ECL Output Current (IOUT) Continuous ......................................................... 50mA Surge ................................................................ 100mA Lead Temperature (soldering, 10 sec.) ..................... 220C Storage Temperature (TS) ....................... -65C to +150C Note 1. Operating Ratings(Note 2) Supply Voltage (VIN) ............................... +3.15V to +3.45V Ambient Temperature (TA) ......................... -40C to +85C Junction Temperature (TJ) ........................................ 125C Package Thermal Resistance EPAD-TQFP (JA), (Note 3) Still-Air .......................................................... 27.6C/W 500lfpm ......................................................... 20.7C/W Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. Measured with die attach pad soldered to PCB, JEDEC standard multi-layer board. Note 2. Note 3. DC ELECTRICAL CHARACTERISTICS VCC = VCCO = VCCA = 3.3V 5%; GND = GNDA = 0V; TA = -40C to +85C Symbol VCC ICC Parameter Power Supply Voltage Power Supply Current Condition Min 3.15 Typ 3.3 210 Max 3.45 280 Units V mA PECL DC ELECTRICAL CHARACTERISTICS VCC = VCCO = VCCA = 3.3V 5%; GND = GNDA = 0V; TA = -40C to +85C Symbol VIH VIL VOH VOL IIL Note 1. Note 2. Parameter Input HIGH Voltage Input LOW Voltage Output HIGH Voltage Output LOW Voltage Input LOW Current Condition Min VCC-1.165 VCC-1.810 Typ Max VCC-0.880 VCC-1.475 VCC-0.830 VCC-1.570 Units V V V V A 50 to VCC-2V 50 to VCC-2V VIN = VIL(Min.), Note 1, 2 VCC-1.075 VCC-1.860 -1.5 The REFCLK+ pin has a nominal 75k pull-down resistor connected to ground. The RECLK- pin has a nominal 75k pull-down resistor connected to ground and a nominal 75k pull-up resistor connected to VCC. TTL DC ELECTRICAL CHARACTERISTICS VCC = VCCO = VCCA = 3.3V 5%; GND = GNDA = 0V; TA = -40C to +85C Symbol VIH VIL VOH VOL IIH IIL IOS Parameter Input HIGH Voltage Input LOW Voltage Output HIGH Voltage Output LOW Voltage Input HIGH Current Input LOW Current Output Short Circuit Current IOH = -2mA IOL = 4mA VIN = 2.7V, VCC = Max. VIN = VCC, VCC = Max. VIN = 0.5V, VCC = Max. VOUT = 0V, (1 sec. Max.) -100 2.0 0.5 +20 +100 -300 -250 Condition Min 2.0 0.8 Typ Max Units V V V V A A A mA M9999-111406 hbwhelp@micrel.com or (408) 955-1690 3 Micrel, Inc. SY87739L AC ELECTRICAL CHARACTERISTICS VCC = VCCO = VCCA = 3.3V 5%; GND = GNDA = 0V; TA = -40C to +85C Symbol tIRF tREFPWH tREFPWL tCSSK tSKCS tSKP tSKPWH tSKPWL tDIS tDIH Parameter REFCLK Input Rise/Fall Times REFCLK Pulse Width High REFCLK Pulse Width Low PROGCS to PROGSK Preset PROGSK to PROGCS Recovery PROGSK Period PROGSK Pulse Width High PROGSK Pulse Width Low PROGDI Data Setup PROGDI Data Hold CLKOUT Duty Cycle CLKOUT Maximum Frequency Aquisition Lock Time Fractional-N VCO Operating Range Wrapper VCO Operating Range 27MHz Reference Clock tCLKPWH / (tCLKPWH + tCLKPWL) Condition Min -- 5 5 100 100 200 70 70 20 20 25 729 -- 540 540 Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Max 2.0 -- -- -- -- -- -- -- -- -- 75 -- 0.1 729 729 Units ns ns ns ns ns ns ns ns ns ns % of UI MHz sec MHz MHz TIMING WAVEFORMS tREFPWH REFCLK tCLKPWH CLKOUT tREFPWL tCLKPWL tCSSK PROGCS tSKPWH PROGSK PROGDI Valid Valid tSKP tSKPWL tDIS tDIH tSKCS Valid M9999-111406 hbwhelp@micrel.com or (408) 955-1690 4 Micrel, Inc. SY87739L FUNCTIONAL DESCRIPTION General The SY87739L AnyClockTM Fractional-N Synthesizer is used in serial data streaming applications, where the incoming data rate on a channel may vary, or where the incoming data rate on a channel is unknown ahead of time. In these situations, a valid output stream must still be generated even in the absence of any edges on the corresponding input stream. Up until now, designers had to resort to sub-optimal solutions such as providing multiple reference oscillators. Beyond the potential noise and EMI issues, the designer has no way to future proof his circuit, as it would prove near impossible to pre-provision all the reference frequencies that might be needed after deployment, yet are unknown at this time. The SY87739L solves this problem by generating exact frequencies for common data streaming protocols, all from one 27MHz reference. If any of these protocols include overhead due to use of common digital wrappers, The SY87739L still generates the exact frequency required, including the overhead. Besides generating reference rates for common protocols directly, the SY87739L also generates reference frequencies for Micrel's SY87721L CDR/CMU, such that it will reliably recover data at any rate between 28Mbps and 2,700Mbps without any gaps. A simple 3-wire MicroWireTM bit-serial interface loads a configuration that describes the desired output reference frequency. All common microcontrollers support this MicroWireTM interface. Those microcontrollers that don't support this interface in hardware can easily emulate the interface in firmware. The large set of possible frequencies that the SY87739L generates, are divided into three classes. First, the sets of frequencies that match a particular data streaming protocol are in the "protocol" category. Second, the set of frequencies that are guaranteed to be near enough to any arbitrary data rate such that the SY87721L will lock are in the "picket fence" category. Third, the set of frequencies that do not fit into either of the first two categories is in the third category, The SY87739L generates these important reference frequencies through two tandem PLL circuits. The first PLL uses a modified fractional-N approach to generate a rational ratio frequency. This PLL is capable of generating all protocol data rates, except for those that include FEC or digital wrapper overhead. A second, more traditional P/Q synthesizer optionally adjusts the output frequency of the first, fractional-N synthesizer, to accommodate these FEC or digital wrapper data rates. The bit serial interface conveys 32 bits of configuration data from a microcontroller to SY87739L. This simple interface consists of an active high chip select, a serial clock (2MHz or less) and a serial data input. Each clock cycle one bit of configuration data transfers to SY87739L. M9999-111406 hbwhelp@micrel.com or (408) 955-1690 Circuit Description The heart of SY87739L is its fractional-N synthesizer, as shown in Figure 1. Loop Filter Input Reference Frequency (fREF) PhaseFrequency Detector/ Charge Pump VCO Output Frequency (fFNOUT) /P Mux /P-1 Control Figure 1. Fractional-N Synthesizer Architecture The two dividers in the feedback path always differ by one count. That is, if one divider is set to divide by P = 5, then the other divider divides by P-1 = 4 . The mux choses between the two based on the control circuit. The idea behind the fractional-N approach is that every input reference edge is used. Only those output edges that are nearest to an input edge get fed back to the phasefrequency comparator. In addition, the nearest output edges are chosen in such a way that the net offset, over a number of edges, zeroes out. It is the control circuit's job to drive the mux such that only the "correct" edges get fed back. In the above fractional-N circuit, if the output frequency should be, for example, 5 times the input frequency, then P is set to 5, and the control circuit sets the mux to only feed back the output of the P divider. If the output frequency should be, for example, 41/2 times the input frequency, then the control circuit alternates evenly between the P and the P-1 divider output. For every two input edges (one to compare against P, and another to compare against P-1), you will get 5 + 4 output edges, yielding an output frequency 9/2 the input frequency. Whereas P sets the integer part of the multiplication factor from input to output frequency, the control circuit determines the fractional part. By mixing the output of the P and P-1 dividers correctly, the control circuit can fashion any output frequency from P-1 times the input to P times the input, as long as that ratio can be expressed as a ratio of integers. 5 Micrel, Inc. SY87739L 1 2 3 1 below, so that its center frequency rests near the target frequency to generate. The fine adjustment forms part of the closed loop. VCO gain is nominally 200MHz per Volt. Fractional-N P/P-1 Divider This is the main divider for the fractional-N loop. The logical value of the output of the control block (Figure 1) defines whether the divider divides by P (values shown in Table 1) or by P-1. The expression for the fractional division becomes: QP1 Fractional division = P QP1 + QP 1 2 3 4 1 2 3 1 2 3 4 1 Figure 2. 11/3 Example Figure 2 shows an example generating an output frequency 3 2/3 times the input frequency. Since the output frequency is between 3 and 4 times the input, P is set to 4. We need to select the P divider twice, and select the P-1 divider once. Multiplying by 4 two times out of three, and multiplying by 3 one time out of three, averages to a multiplication of 32/3 . The top waveform is the reference input. The bottom waveform is the multiplied output. The waveform in the middle shows those edges from the output that most closely matches a corresponding reference waveform edge. The control circuit must generate a repeating pattern to the mux of something like "101", so that the P divider is selected twice, and the P-1 divider is selected once, every three reference edges. Fractional-N Phase-Frequency Detector This circuit, besides generating "pump up" and "pump down" signals, also generates delta phase signals for use by the lock detect circuit. This detector circuit also accepts a gating signal from the fractional-N control block. When gated, the phase detector generates neither pump up nor pump down pulses. Fractional-N Charge Pump This circuit converts the "pump up" and "pump down" signals from the phase-frequency detector into current pulses. An external loop filter integrates these current pulses into a control voltage. Charge pump current is selectable. This modifies loop gain as follows: During acquisition of the reference, the charge pump current is fixed at 20A. Once the acquisition sequencer has completed center frequency trimming, then it changes the current of this charge pump to 50A. Fractional-N VCO This circuit converts the voltage integrated by the external loop filter into a digital clock stream. The frequency of this clock varies based on this control voltage. This VCO has a coarse and a fine input, with a combined range of 540MHz to 729MHz. The coarse input trims the VCO, as described ( ) Where QP is the number of reference clock periods during which the divider must divide by P and QP-1 is the number of reference clock periods during which the divider must divide by P-1. Care should be exercised when selecting the value of P (Table 1) so that the voltage-controlled oscillator (VCO) of the fractional-N PLL is not driven out of range. The following conditions must be met: fVCO (min) < fREF x Fractional division < fVCO (max) or QP1 fVCO (min) < fREF x P < fVCO (max) (QP1 + QP ) Where, fVCO (min) = 540MHz fVCO (max) = 729MHz fREF = frequency of the reference clock. DivSel3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 DivSel2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 DivSel1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 DivSel0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 P 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Table 1. DivSel Divider Setting M9999-111406 hbwhelp@micrel.com or (408) 955-1690 6 Micrel, Inc. SY87739L Fractional-N Control This circuit controls the P/P-1 divider, selecting the appropriate divide ratio, either P or P-1, in the correct pattern. As explained in the example of Figure 2 above, controlling the P/P-1 divider amounts to generating a repeating binary bit stream. In that example, a "1" represents dividing by 4, and a "0" represents dividing by 3. The full cycle, "101", says to divide by 4 twice, and to divide by 3 once. In the general case, the pattern "101" need not change based on the P divider value. To multiply by 14/3 instead of 11/3, for example, the same "101" pattern would be used, but we would alternate dividing by 5 and 4, instead of dividing by 4 and 3. The P value, in effect, represents the integer part of the multiplication factor. The repeating binary bit pattern really depends only on the number of times to divide by P, and the number of times to divide by P-1. We label the number of times to divide by P as QP, and the number of times to divide by P-1 as QP-1. The fractional-N synthesizer generates its output frequency as per this formula: fFNOUT QP1 = P xf QP + QP1 REF 11110 11110 1110 11110 1110 Table 2 shows how Bresenham's algorithm works. The first column is an accumulator. It starts at zero, but otherwise takes the result from the fourth column of the previous row. The second column is the value to add to the accumulator at each step. In the general case, this is always QP-1. The third column forms the sum. The fourth column takes the sum modulo (QP + QP-1). The last column is "0" whenever the modulo changes the sum. Note that the Table has 23 rows, before the sum is zero, and the entire algorithm repeats itself. Accum 0 5 10 15 20 2 7 12 17 22 4 9 14 19 1 6 11 16 21 3 8 13 18 Add 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Sum 5 10 15 20 25 7 12 17 22 27 9 14 19 24 6 11 16 21 26 8 13 18 23 Modulo 5 10 15 20 2 7 12 17 22 4 9 14 19 1 6 11 16 21 3 8 13 18 0 Bit 1 1 1 1 0 1 1 1 1 0 1 1 1 0 1 1 1 1 0 1 1 1 0 In our figure two example, we multiply by 11/3, or 41/3. Matching against the formula, P = 4, QP-1 = 1, and QP = 2. The SY87739L accepts QP and QP-1 values from its MicroWireTM interface, where they exist as the 5-bit values "qp" and "qpm1." Both values are unsigned binary numbers. QP and QP-1 are both constrained to be 31 or less, and their sum is also constrained to be 31 or less. That means that the denominator in the above formula must be 31 or less. As would be expected from the formula, setting QP to zero causes frequency multiplication exactly by P-1. Setting QP-1 to zero causes frequency multiplication exactly by P. The SY87739L behavior is undefined if both QP and QP-1 are both set to zero. In the general case, the length of the repeating binary bit pattern is QP + QP-1. It consists of QP "1", and QP-1 "0." The SY87739L accomplishes this by implementing Bresenham's algorithm in hardware. To see how this works, we need a more complicated example. Let's say we need to multiply by 110/23, or 5 - 5/23. In this example, P = 5, QP-1 = 5, and QP = 18. The naive approach would generate a bit pattern of: 11111 11111 11111 11100 000 The spaces between groups of five digits are added for readability only. This pattern is 23 bits long, with QP (that is, 18) "1" and QP-1 (that is, 5) "0", so it will multiply correctly, but it doesn't match P/P-1 divider edges to input edges in the best way possible. In fact, the best pattern, in terms of minimizing distance between divider and reference input edges, is: M9999-111406 hbwhelp@micrel.com or (408) 955-1690 Table 2. 5/23 Example Note that the sequence of bits in the last column, reading down, is the optimal pattern to generate. The choice of repeating bit pattern reduces jitter because a fractional-N synthesizer relies on edges temporarily not matching, but averaging out over some time interval. Anything that reduces the timing disparity between edges arriving at the phase-frequency comparator will reduce jitter. Center Frequency Trim This circuit block generates two identical reference voltages for the two VCO on the SY87739L. This voltage pair can be digitally trimmed. Trimming occurs under control of the acquisition sequencer, which trims for center frequency of the fractional-N synthesizer only. The wrapper synthesizer VCO is matched to the fractional-N VCO. Both VCO are fed 7 Micrel, Inc. SY87739L the same coarse adjustment voltage, and so both center nominally at the same frequency. An 8-bit counter implements the voltage steps. The acquisition sequencer steps through this counter, which changes its voltage by about 12mV per step. The coarse input to the VCO is nominally set at 500MHz per Volt. The acquisition sequencer exercises the center frequency trim circuit so that the VCO control voltage ends up within about 12mV of where it should be, were it exactly centered for the desired output frequency. Lock Detector The SY87739L ensures proper operation of both synthesizers by verifying that both PLL have achieved lock. The LOCKED output asserts active high only when this is the case, that is, both PLL are locked. The SY87739L implements a digital lock detector that is both simple and robust. Each phase-frequency detector provides a charge pump output that is the logical OR of pump up and pump down pulses. The lock detect circuit processes this charge pump output with a pulse width discriminator. Once each reference clock rising edge, the discriminator will produce a pulse, only if the phase difference between the feedback divider and the reference input is too large. These pulses are subsequently processed digitally. A PLL that is out of lock, is declared to be in lock only if 256 consecutive reference clocks have NO large phase errors, as reported by the pulse width discriminator. Any large phase error event, even a single one, that arrives before lock is declared, will reset the circuit. Once in lock, a PLL is declared out of lock if more largephase-difference than small-phase-difference events occur that is, if over time, a net of 256 large-phase-difference events occur. That is accomplished by counting up when large-phase-difference events occur and counting down in the case of small-phase events. Wrapper Synthesizer The frequency generated by the fractional-N PLL is further processed by a more classical PLL circuit, as shown in Figure 3. Loop Filter Input Frequency (fFNOUT) PhaseFrequency Detector/ Charge Pump synthesizer generates just a few ratios near 1. The wrapper modifies the frequency based on the values of M and N, the dividers, as per: 540MHz fWROUT = QP1 N N x fFNOUT = x P M M QP1 + QP x fREF 729MHz Wrapper Phase-Frequency Detector This circuit generates pump up and pump down signals for the charge pump, and also generates delta phase for the lock detector. Wrapper Charge Pump This circuit converts the pump signals from the phasefrequency detector into current pulses. Charge pump current is fixed at about 20A. An external loop filter integrates these current pulses into a control voltage. Wrapper VCO This circuit matches the fractional-N VCO in construction and operation, so that the center frequency trim circuit can center both the fractional-N VCO and the wrapper VCO at about the same frequency. Wrapper M Divider This circuit forms the denominator of the ratio by which the wrapper synthesizer modifies the fractional-N output frequency. The division ratio is selected via MicroWireTM, as the 3-bit MdivSel register, as per Table 3 . MdivSel2 0 0 0 0 1 1 1 1 MdivSel1 0 0 1 1 0 0 1 1 MdivSel0 0 1 0 1 0 1 0 1 Divisor 16 16 18 17 31 14 32 15 Table 3. MdivSel Divisor Control The divisors are in two sets. The first set consists of the divisors 14, 15, 16, 17, and 18. The second set consists of 31 and 32. Both M and N must be chosen from the same set. For example, an N divisor of 31 and an M divisor of 17 results in undefined behavior. The ratio must be kept M N /M VCO Output Frequency (fWROUT) /N smaller than 17 18 , that is, is not allowed. 14 14 Figure 3. Wrapper Architecture This circuit further modifies the frequency generated by the fractional-N loop. This comes in handy where digital wrapper and/or FEC is implemented. The wrapper M9999-111406 hbwhelp@micrel.com or (408) 955-1690 Wrapper N Divider This circuit forms the numerator of the ratio by which the wrapper synthesizer modifies the fractional-N output frequency. The division ratio is selected via MicroWireTM, as the 3-bit NdivSel register, as per Table 4. 8 Micrel, Inc. NdivSel2 0 0 0 0 1 1 1 1 NdivSel1 0 0 1 1 0 0 1 1 NdivSel0 0 1 0 1 0 1 0 1 Divisor 16 16 18 17 31 14 32 15 SY87739L The divisor value is selected via MicroWireTM. The 5-bit PostDivSel register determines the divisor value. It is set as per Table 5. The SY87739L does not guarantee a 50% duty cycle output. It is designed to provide well timed rising edges only. MicroWireTM Interface This standard bit-serial interface eases interfacing the SY87739L to microcontrollers. The SY87739L accepts one data bit on PROGDI per rising edge on PROGSK. The data is ignored when PROGCS is inactive low. When PROGCS is active high, bits are shifted into the SY87739L. The falling edge of PROGCS then initiates acquisition of the output frequency defined by the 32-bit program just loaded into the SY87739L. This means that, if the user wishes to re-acquire based on the same program, PROGCS needs to toggle high then low. Programming To program the SY87739L to generate a certain frequency: 1. Determine the required values of the programming parameters, as summarized in Table 6. 2. Set PROGCS active high. 3. Shift in each of the 32 bits, as per Table 6. The fields are loaded in sequence, from the first row to the last row. For each multi-bit field, the most significant bit is shifted in first. Shift the bits in through PROGDI, clocking them with PROGSK edges. 4. Set PROGCS inactive low. 5. Wait for LOCKED to assert high. Field Preamble qp qpm1 divsel mfg. PostDivSel NdivSel MdivSel # Bits 4 5 5 4 3 5 3 3 Reference always "0000" Section: Gating the P/P-1 Divider Section: Gating the P/P-1 Divider Table 1 always "000" Table 5 Table 4 Table 3 Table 4. NdivSel Divisor Control P Divider The output of the wrapper synthesizer is post divided down before appearing at the CLKOUT pins. Notice that, given the range of the wrapper VCO (540MHz to 729MHz) and the maximum and minimum division ratios of the P divider (1 to 60, as shown in Table 5), the minimum and maximum frequency of CLKOUT is 10MHz and 729MHz respectively. 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 PostDivSel Bit 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Divisor 1 3 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 20 22 24 26 28 30 32 36 40 44 48 52 56 60 Table 6. Programming Sequence The SY87739L generates exact frequencies for common serial data streaming protocols. Summary programming information appears in the next section. The SY87739L also enables Micrel's SY87721L AnyRateTM CDR to decode virtually anything within its range of operation, all from a 27.000MHz reference. Details about how to program the SY87739L in the general case, including derivation of programs for both the standard protocols and the AnyRateTM application, appear in an applications note. Table 5. Setting to Program the Division Ratio of the P Divider M9999-111406 hbwhelp@micrel.com or (408) 955-1690 9 Micrel, Inc. SY87739L Standard Protocol Applications From a single 27.000MHz reference input, the SY87739L can generate exactly correct frequencies for at least the 18 protocols listed in Table 7. This table also shows how to program the SY87739L for each protocol listed. This table assumes no digital wrapper. If your system includes such a wrapper, then modify the NdivSel and MdivSel bits accordingly. Protocol ETR OC-1 Fast Ethernet FDDI 1/8 Fibre Channel General OC-3/STM-1 ESCON 1/4 Fibre Channel 1/2 Fibre Channel OC-12/STM-4 Fibre Channel Gigabit Ethernet D1 Video HDTV Infiniband 2x Fibre Channel OC-48/STM-16 OC-48/STM-16 SY87739L Fout (MHz) 32 51.84 50 125 13.28125 150 155.52 50 26.5625 53.125 622.08 106.25 156.25 69 92.8125 125 212.5 155.52 622 Programming Bits 0000 10011 01000 0111 000 10010 101 101 0000 00001 11000 0111 000 01100 101 101 0000 00010 11001 1000 000 01101 101 101 0000 00100 10111 0111 000 00101 101 101 0000 01011 00111 0111 000 11100 101 101 0000 00010 00111 0110 000 00100 101 101 0000 00001 11000 0111 000 00100 101 101 0000 00010 11001 1000 000 01101 101 101 0000 01011 00111 0111 000 10100 101 101 0000 01011 00111 0111 000 01100 101 101 0000 00011 11000 0111 000 00000 101 101 0000 01011 00111 0111 000 00110 101 101 0000 00100 10111 0111 000 00100 101 101 0000 00001 00000 0110 000 01001 101 101 0000 00001 01111 1000 000 00111 101 101 0000 00100 10111 0111 000 00100 101 101 0000 01011 00111 0111 000 00011 101 101 0000 00001 11000 0111 000 00100 101 101 0000 00001 11000 0111 000 00000 101 101 Table 7. Protocol Listings Loop Filter Values Each PLL in the SY87739L adjusts its loop gain through an external loop filter. Figure 4 shows Micrel's recommended values for these. 2k 0.1F FNCVF+ or WRVCF+ FNCVF- or WRVCF- Figure 4. Recommended Loop Filter Values M9999-111406 hbwhelp@micrel.com or (408) 955-1690 10 Micrel, Inc. SY87739L SYSTEM BLOCK DIAGRAM SY889x3 FIBER PIN DIODE TIA POST AMP SY87721L RDATA SY87724L 4, 5, 8, 10 bits RCLK DEMUX AnyRate CDR TCLK One REF_OSC MUX 4, 5, 8, 10 bits SY87739L REF_CLK CMU AnyClock Fractional-N Synthesizer 8 bits P LOCK SY889x2 FIBER LASER DIODE LASER DIODE DRIVER M9999-111406 hbwhelp@micrel.com or (408) 955-1690 11 Micrel, Inc. SY87739L FUNCTIONAL BLOCK DIAGRAM Center Frequency Trim FN VCF Loop Filter REFCLK PhaseFrequency Detector Charge Pump VCO Fine FN Delta Phase P/(P-1) Divider Fractional-N Control WR Delta Phase Lock Detector Locked WR VCF Loop Filter M Divider PhaseFrequency Detector Charge Pump VCO PROGCS PROGDI PROGSK MicroWire Interface N Divider Aquisition Sequencer P Divider CLKOUT RELATED PRODUCT AND SUPPORT DOCUMENTATION Part Number SY87739L-EVAL Function Fractional-N Synthesizer Evaluation Board Data Sheet Link www.micrel.com/product-info/eval_boards.shtml M9999-111406 hbwhelp@micrel.com or (408) 955-1690 12 Micrel, Inc. SY87739L 32 LEAD EPAD-TQFP 7mm X 7mm (DIE UP) (H32-2) Package EP- Exposed Pad Rev. 01 Die CompSide Island Heat Dissipation Heat Dissipation VEE Heavy Copper Plane VEE Heavy Copper Plane PCB Thermal Consideration for 32-Pin EPAD-TQFP Package MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2006 Micrel, Incorporated. M9999-111406 hbwhelp@micrel.com or (408) 955-1690 13 |
Price & Availability of SY87739LHY
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |