 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MC74VHC1G66/D Product Preview Analog Switch The MC74VHC1G66 is an advanced high speed CMOS bilateral analog switch fabricated with silicon gate CMOS technology. It achieves high speed propagation delays and low ON resistances while maintaining CMOS low power dissipation. This bilateral switch controls analog and digital voltages that may vary across the full power-supply range (from VCC to GND). The MC74VHC1G66 is compatible in function to a single gate of the High Speed CMOS MC74VHC4066 and the metal-gate CMOS MC14066. The device has been designed so that the ON resistances (RON) are much lower and more linear over input voltage than RON of the metal-gate CMOS or High Speed CMOS analog switches. The ON/OFF control inputs are compatible with standard CMOS outputs; with pull-up resistors, it is compatible with LSTTL outputs. * * * * * * * * High Speed: tPD = TBD (Typ) at VCC = 5 V Low Power Dissipation: ICC = 2 mA (Max) at TA = 25C Diode Protection Provided on Inputs and Outputs Improved Linearity and Lower ON Resistance over Input Voltage than the MC14066 or the HC4066 Pin and Function Compatible with Other Standard Logic Families Latchup Performance Exceeds 300 mA ESD Performance: HBM > 2000 V; MM > 200 V, CDM > 1500 V Chip Complexity: 11 FETs or 3 Equivalent Gates MC74VHC1G66 DF SUFFIX 5-LEAD SOT-353 PACKAGE SC-88A CASE 419A-01 FUNCTION TABLE On/Off Control Input L H State of Analog Switch Off On IN/OUT XA 1 OUT/IN YA 2 GND 3 5 VCC 4 ON/OFF CONTROL 5-Lead SOT-353 Pinout (Top View) V9d ON/OFF CONTROL IN/OUT XA U X1 1 1 U OUT/IN YA Pin 1 d = Date Code Logic Symbol DEVICE ORDERING INFORMATION Device Nomenclature Motorola Circuit Indicator MC Temp Range Identifier 74 Device Function 66 Package Suffix DF Marking Diagram Device Order Number D i Od N b MC74VHC1G66DFT1 Technology VHC1G Tape and Reel Suffix T1 Package Pk Type SC-88A Tape and R l T d Reel Size 7-Inch/3000 Unit This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. 8/98 (c) Motorola, Inc. 1998 1 REV 0 MC74VHC1G66 ABSOLUTE MAXIMUM RATINGS Characteristics DC Supply Voltage Digital Input Voltage Analog Output Voltage Digital Input Diode Current DC Supply Current, VCC and GND Power dissipation in still air, SC-88A Lead temperature, 1 mm from case for 10 s Storage temperature Derating -- SC-88A Package: -3 mW/_C from 65_ to 125_C Symbol VCC VIN VIS IIK ICC PD TL Tstg Value -0.5 to +7.0 -0.5 to VCC +0.5 -0.5 to VCC + 0.5 -20 +25 200 260 -65 to +150 Unit V V V mA mA mW C C RECOMMENDED OPERATING CONDITIONS Characteristics DC Supply Voltage Digital Input Voltage Analog Input Voltage Static or Dynamic Voltage Across Switch Operating Temperature Range Input Rise and Fall Time ON/OFF Control Input Symbol VCC VIN VIS VIO* TA -55 Min 4.5 GND GND Max 5.5 VCC VCC 100 +125 Unit V V V mV C tr , tf ns/V VCC = 3.3V 0.3V 0 100 VCC = 5.0V 0.5V 0 20 * For voltage drops across the switch greater than 100mV (switch on), excessive VCC current may be drawn; i.e. the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded. MOTOROLA 2 VHC Data - Advanced CMOS Logic DL203 -- Rev 1 MC74VHC1G66 DC ELECTRICAL CHARACTERISTICS VCC Symbol VIH Parameter Minimum High-Level Input Voltage ON/OFF Control Input Maximum Low-Level Input Voltage ON/OFF Control Input Maximum Input Leakage Current ON/OFF Control Input Maximum Quiescent Supply Current Maximum "ON" Resistance Test Conditions RON = Per Spec (V) 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 0 to 5.5 5.5 2.0 3.0 4.5 2.0 3.0 4.5 5.5 25 12 8 25 12 8 Min 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 0.1 TA = 25C Typ Max TA 85C Min 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 1.0 Max TA 125C Min 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 1.0 Max Unit V VIL RON = Per Spec V IIN VIN = VCC or GND A ICC RON VIN = VCC or GND VIO = 0V VIN = VIH VIS = VCC or GND IIS 20mA (Figure 1) Endpoints VIN = VIH VIS = VCC or GND IIS 20mA (Figure 1) 2.0 50 20 15 50 20 15 0.1 20 70 30 25 65 26 23 0.5 40 100 45 35 90 40 32 1.0 A W W A IOFF Maximum Off-Channel Leakage Current Maximum On-Channel Leakage Current VIN = VIL VIO = VCC or GND Switch Off (Figure 2) VIN = VIH VIS = VCC or GND Switch On (Figure 3) ION 5.5 0.1 0.5 1.0 A II I I I I I I I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIII IIIIIIII I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII I I I I II I I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII I I IIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIII II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III I II I I I I I I I I III I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII III I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS (Cload = 50 pF, Input tr/tf = 3.0ns) Symbol S bl Parameter P Test C di i T Conditions VCC (V) 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 0.0 5.0 TA = 25C Typ 1 0 0 0 TA 85C TA 125C Min Max 5 2 1 1 Min Max 6 3 1 1 Min Max 7 4 2 1 Unit Ui ns tPLH, tPHL Maximum Propogation Delay, Input X to Y Maximum Propogation Delay, ON/OFF Control to Analog Output Maximum Propogation Delay, ON/OFF Control to Analog Output Maximum Input Capacitance YA = Open Figure 4 tPLZ, tPHZ RL = 1000 W Figure 5 15 8 6 4 15 8 6 4 3 4 4 35 15 10 7 35 15 10 7 10 10 10 46 20 13 9 46 20 13 9 10 10 10 57 25 17 11 57 25 17 11 10 10 10 ns tPZL, tPZH RL = 1000 W Figure 5 ns CIN ON/OFF Control Input Contol Input = GND Analog I/O Feedthrough pF Typical @ 25C, VCC = 5.0V 18 CPD Power Dissipation C P Di i i Capacitance (N i (Note 1 ) 1.) pF F 1. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. VHC Data - Advanced CMOS Logic DL203 -- Rev 1 3 MOTOROLA MC74VHC1G66 II II I I I I II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I II II I II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II I I III I I I II II I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II I II I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II II I I I III I I I II I II I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I III I I I II I I II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIII I II I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I II II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted) Symbol Parameter Test Conditions VCC 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 Limit 25C 150 175 200 -50 -50 -50 -40 -40 -40 Unit BW Maximum On-Channel Bandwidth or Minimum Frequency Response Figure 7 fin = 1 MHz Sine Wave Adjust fin voltage to obtain 0 dBm at VOS Increase fin = frequency until dB meter reads -3dB RL = 50W, CL = 10 pF fin = Sine Wave Adjust fin voltage to obtain 0 dBm at VIS fin = 10 kHz, RL = 600W, CL = 50 pF fin = 1.0 kHz, RL = 50W, CL = 10 pF MHz ISOoff Off-Channel Feedthrough Isolation Figure 8 dB NOISEfeed Feedthrough Noise Control to Switch Figure 9 Vin 1 MHz Square Wave (tr = tf = 2ns) Adjust RL at setup so that Is = 0 A RL = 600W, CL = 50 pF RL = 50W, CL = 10 pF 45 60 130 25 30 60 mVPP THD Total Harmonic Distortion Figure 10 fin = 1 kHz, RL = 10kW, CL = 50 pF THD = THDMeasured - THDSource VIS = 3.0 VPP sine wave VIS = 4.0 VPP sine wave VIS = 5.0 VPP sine wave % 3.3 4.5 5.5 0.20 0.10 0.06 1. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. MOTOROLA 4 VHC Data - Advanced CMOS Logic DL203 -- Rev 1 MC74VHC1G66 PLOTTER POWER SUPPLY - + VCC 1 2 VCC 3 4 A 3 4 5 VCC 1 2 5 VIL VCC DC PARAMETER ANALYZER COMPUTER Figure 1. On Resistance Test Set-Up Figure 2. Maximum Off-Channel Leakage Current Test Set-Up VCC A N/C 1 2 3 4 5 VCC 1 VIH TEST POINT 2 3 4 5 VCC VCC Figure 3. Maximum On-Channel Leakage Current Test Set-Up Figure 4. Propagation Delay Test Set-Up Switch to Position 1 when testing tPLZ and tPZL Switch to Position 2 when testing tPHZ and tPZH TEST POINT VCC 1 1 2 VCC 1 2 *Includes all probe and jig capacitance. RL 2 CL* 3 4 N/C 2 3 4 5 VCC N/C 1 5 VCC A Figure 5. Propagation Delay Output Enable/Disable Test Set-Up Figure 6. Power Dissipation Capacitance Test Set-Up VHC Data - Advanced CMOS Logic DL203 -- Rev 1 5 MOTOROLA MC74VHC1G66 VOS 0.1 mF fin 1 2 dB Meter CL* 3 4 dB Meter RL CL* 5 VCC fin 0.1 mF 1 2 3 4 5 VIS VOS VCC *Includes all probe and jig capacitance. *Includes all probe and jig capacitance. Figure 7. Maximum On-Channel Bandwidth Test Set-Up Figure 8. Off-Channel Feedthrough Isolation Test Set-Up (VCC)/2 To Distortion Meter (VCC)/2 VIS 0.1 mF RL VOS CL* fin 1 2 3 4 5 VCC RL RL VOS CL* IS 1 2 3 4 5 VCC v 1 MHz IN t r + t + 2 ns f V VCC GND *Includes all probe and jig capacitance. *Includes all probe and jig capacitance. Figure 9. Feedthrough Noise, ON/OFF Control to Analog Out, Test Set-Up Figure 10. Total Harmonic Distortion Test Set-Up tr Control 90% 10% tPZL 50% VCC Analog Out 50% VCC tPZH 90% 50% VCC tPLZ High Impedance 10% VOL VOH tf VCC XA VCC 50% tPLH 50% VCC tPHL VOH YA 50% VCC VOL High tPHZ Impedance Figure 11. Propagation Delay, Analog In to Analog Out Waveforms Figure 12. Propagation Delay, ON/OFF Control MOTOROLA 6 VHC Data - Advanced CMOS Logic DL203 -- Rev 1 MC74VHC1G66 OUTLINE DIMENSIONS DF SUFFIX 5-LEAD SOT-353 PACKAGE SC-88A CASE 419A-01 ISSUE B G V DIM A B C D G H J K N S V A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --- 0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 0.012 0.016 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --- 0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 0.30 0.40 5 4 S 1 2 3 -B- D 5 PL 0.2 (0.008) M B M N 0.5 mm (min) J C SOT-353 H K 0.4 mm (min) 1.9 mm VHC Data - Advanced CMOS Logic DL203 -- Rev 1 7 MOTOROLA 0.65 mm 0.65 mm EE EE EE EE EE EE EE EE EE EE EE MC74VHC1G66 10 PITCHES CUMULATIVE TOLERANCE ON TAPE 0.2 mm (0.008") E A0 SEE NOTE 1 B1 K0 SEE NOTE 1 K t TOP COVER PLATE D P2 P0 F W + B0 P + + D1 FOR COMPONENTS 2.0 mm x 1.2 mm AND LARGER FOR MACHINE REFERENCE ONLY INCLUDING DRAFT AND RADII CONCENTRIC AROUND B0 EMBOSSMENT USER DIRECTION OF FEED CENTER LINES OF CAVITY *TOP COVER TAPE THICKNESS (t1) 0.10 mm (0.004") MAX. R MIN. TAPE AND COMPONENTS SHALL PASS AROUND RADIUS "R" WITHOUT DAMAGE BENDING RADIUS EMBOSSED CARRIER EMBOSSMENT 10 MAXIMUM COMPONENT ROTATION TYPICAL COMPONENT CAVITY CENTER LINE 100 mm (3.937") 1 mm MAX TAPE 1 mm (0.039") MAX 250 mm (9.843") TYPICAL COMPONENT CENTER LINE CAMBER (TOP VIEW) ALLOWABLE CAMBER TO BE 1 mm/100 mm NONACCUMULATIVE OVER 250 mm Figure 13. Carrier Tape Specifications EMBOSSED CARRIER DIMENSIONS (See Notes 1 and 2) Tape Size 8 mm B1 Max 4.55 mm (0.179") D 1.5 +0.1/ -0.0 mm (0.059 +0.004/ -0.0") D1 1.0 mm Min (0.039") E 1.75 0.1 mm (0.069 0.004") F 3.5 0.5 mm (1.38 0.002") K 2.4 mm (0.094") P 4.0 0.10 mm (0.157 0.004") P0 4.0 0.1 mm (0.156 0.004") P2 2.0 0.1 mm (0.079 0.002") R 25 mm (0.98") T 0.3 0.05 mm (0.01 +0.0038/ -0.0002") W 8.0 0.3 mm (0.315 0.012") 1. Metric Dimensions Govern-English are in parentheses for reference only. 2. A0, B0, and K0 are determined by compnent size. The clearance between the components and the cavity must be within 0.05 mm min to 0.50 mm max. The component cannot rotate more than 10 within the determined cavity MOTOROLA 8 VHC Data - Advanced CMOS Logic DL203 -- Rev 1 MC74VHC1G66 t MAX 1.5 mm MIN (0.06") A 20.2 mm MIN (0.795") 13.0 mm 0.2 mm (0.512" 0.008") 50 mm MIN (1.969") FULL RADIUS G Figure 14. Reel Dimensions REEL DIMIENSIONS Tape Size 8 mm A Max 330 mm (14.1") G 8.400 mm, +1.5 mm, -0.0 (0.33", +0.059", -0.00) t Max 14.4 mm (0.56") DIRECTION OF FEED BARCODE LABEL POCKET HOLE Figure 15. Reel Winding Direction VHC Data - Advanced CMOS Logic DL203 -- Rev 1 9 MOTOROLA MC74VHC1G66 CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN COMPONENTS TAPE LEADER NO COMPONENTS 400 mm MIN DIRECTION OF FEED Figure 16. Tape Ends for Finished Goods "T1" PIN ONE TOWARDS SPROCKET HOLE SOT-353 (5 Pin) DEVICE User Direction of Feed Figure 17. Reel Configuration Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 Customer Focus Center: 1-800-521-6274 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 - http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ JAPAN: Nippon Motorola Ltd.; SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan. 81-3-5487-8488 MOTOROLA 10 MC74VHC1G66/D VHC Data - Advanced CMOS Logic DL203 -- Rev 1 |
Price & Availability of ON1680
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |